587b120v.pdf

05016
587B051 - 587B301
Only One Name Means ProTek’Tion™
120v ac power line surge suppressor
Description
The 587B Series of 120 Volt AC Surge Suppressors is designed for use by the OEM, equipment installer and or maintenance contractor. These modules employ a three stage technology proven to be the most cost effective and reliable
method in protecting sensitive electronic equipment from over voltage transients. This series is designed to protect AC
powered equipment from the 6,000 volt peak open circuit voltage and 3,000 Amp short circuit current as defined in
ANSI/IEEE C62.41, Category C1.
The 587B Series offers a high degree of protection against 120 VAC EMI line noise. It is ideal for protecting 400 Volt
components because the solid state TVS technology assures that the line-to-neutral voltage will not exceed 400
Volts. While the modules are designed for transient voltage protection, the advanced circuitry will also attenuate the
amplitude and slow the rate of rise of high frequency noise acting as an EMI filter. The 587B Series includes differential mode protection, which is effective in reducing interference from line to equipment and are effective in reducing
equipment generated noise to meet FCC, VDE and CSA interference requirements.
587B
Features
applications
• Compatible with IEC 61000-4-5 (Surge): 1kA, 8/20µs, Level 4 (LineGnd) & 333A, Level 4 (Line-Line)
• Meets ANSI/IEEE C62.41 Requirements
• Listed to CSA, File LR65240
• Differential and Common Mode Protection
• Low Clamping Voltage
• Nanosecond Response Time
• Long Life and Maintenance Free
• Hard Wired Equipment AC Power Protection
• Load Side Distribution Systems
• Secondary Protection for Light Industrail AC Power
Mechanical characteristics
• Plastic Package
• Approximate Weight: 485 grams
• Flammability Rating UL 94V-0
figure 2
typical clamping action of a 16a module
8
6
6
4
Kilovolts
Kilovolts
figure 1
transient voltage threat condition
4
2
0
2
0
0
10
20
30
40
50
60
0
t - Time - µs
10
20
30
40
50
60
t - Time - µs
Figures 1 and 2 are photographs of digitized waveforms showing the typical clamping action of a 16A module. A 12 Ohm resistor is used to represent a 10A equipment load. The load is then subjected to the ANSI/IEEE C62.41 Catagory CI test conditions (6000V/3000A). These photographes
contrast the effect on equipment with and without the protector.
05016.R7 9/12
Page 1
www.protekdevices.com
05016
587B051 - 587B301
Only One Name Means ProTek’Tion™
typical device characteristics
MAXIMUM RATINGS @ 25°C Unless Otherwise Specified
PARAMETER
SYMBOL
VALUE
UNITS
VO
130
Volts AC
Operating Line Voltage: +10%
Line Current: 587B051/587B151/587B201/587B301
-
5/15/20/30
Amps
Peak Transient Voltage
-
6000
Volts
Peak Transient Current
-
3000
Amps
Current Leakage @ 130 Volts AC: Line-to-Neutral & Neutral-to-Ground
-
1 & 0.5
mA
Operating Temperature - Note 1
TA
-40 to 85
°C
TSTG
-40 to 85
°C
Storage Temperature - Note 1
Notes
1. Measured at the center of the mounting surface.
ELECTRICAL CHARACTERISTICS @ 25°C Unless Otherwise Specified
Protection
mode
(Note 1)
maximum
clamping voltage
(Note 2)
open circuit
voltage
(Note 2)
short circuit
current
(Note 2)
volts
@1.2/50µs
volts
@ 8/20µs
amps
295
1000
500
Line to Neutral
Line to Neutral
350
6000
3000
Neutral to Ground
500
1000
500
Neutral to Ground
650
6000
3000
Notes
1. Differential Mode Protection: Line to Neutral. Common Mode Protection: Neutral to Ground.
2. Test condition responses to transient voltages.
filter characteristics (Noise Attenuation db)
Frequency (MHz)
0.15
0.5
1.0
5.0
10
30
Common Mode Attenuation
10
25
35
55
50
40
Differential Mode Attenuation
30
55
55
55
50
45
05016.R7 9/12
Page 2
www.protekdevices.com
05016
587B051 - 587B301
Only One Name Means ProTek’Tion™
typical device characteristics
arrestor definitions
Clamping Voltage: The clamping voltage of an arrester is the voltage that appears across its terminals during conduction of a transient current.
Standard Wave Form: The waveform of a surge current or voltage is designated by a combination of two numbers. The first number is for the time of the wave front
expressed in microseconds from zero to the peak of the wave. The second number is for the time of the wavetail also expressed in microseconds from zero to the
instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 µs waveform.
Transient Current: The transient current of an arrestor is the peak surge current which flows through the arrester when voltage clamping occurs.
operation
For maximum effectiveness, the protector should be installed directly after the AC line on/off switch and fuse. This will protect the electronics from the AC line switch
arcing and the severe transients caused by a fuse clearing.
Some heat is produced when operating at full current load, and heat sinking may be required to maintain case temperature below 85°C. The case temperature is
measured at the center of the mounting surface. The unit should not be mounted to a low combusting temperature material such as wood.
High energy transients will cause a large circulating current in the AC input line (2,500A is possible). To prevent electromagnetic coupling, the AC line on the input side
of the protector must be dressed away from other wiring, magnetic shielding may be required. In addition, the electrical service must be connected to a low impedance earth ground.
05016.R7 9/12
Page 3
www.protekdevices.com
05016
587B051 - 587B301
Only One Name Means ProTek’Tion™
package information
OUTLINE DIMENSIONS
INCHES
MILLIMETERS
p/n
wEIGHT
A
B
C
D
E
F
G
A
B
C
D
E
F
g
587B051
250
2.00
2.00
2.50
3.00
1.50
0.60
0.169
50.8
50.8
63.5
76.2
38.2
15.2
4.29
587B151
500
3.00
2.00
3.50
4.00
1.50
0.60
0.169
76.2
50.8
89.0
102.0
38.2
15.2
4.29
587B201
750
3.00
3.00
3.50
4.00
1.50
0.60
0.169
76.2
76.2
89.0
102.0
38.2
15.2
4.29
587B301
850
3.00
3.00
3.50
4.00
1.50
0.60
0.169
76.2
76.2
89.0
102.0
38.2
15.2
4.29
D
F
C
LINE IN
LINE OUT
DEVICE
MARKING
G
E
NEUTRAL
B
GROUND
A
ORDERING INFORMATION
base PART NUMBER
(xx = Voltage)
MARKING
587Bxxx
Part Number, Date Code, Voltage, Logo, Current Rating, CSA Logo
05016.R7 9/12
Page 4
www.protekdevices.com
05016
587B051 - 587B301
Only One Name Means ProTek’Tion™
company information
COMPANY PROFILE
In business more than 20 years, ProTek Devices™ is a privately-held company located in Tempe, Arizona, that offers a product line of transient voltage suppressors (TVS); avalanche breakdown diodes; steering diode TVS arrays and other surge suppressor component products.
These TVS devices protect electronic systems from the effects of lightning, electrostatic discharge (ESD), nuclear electromagnetic pulses
(NEMP), inductive switching and EMI / RFI. ProTek Devices also offers high performance interface and linear products that include analog
switches; multiplexers; LED drivers; audio control ICs; RF and related high frequency products. The analog devices work in a host of consumer; industrial; automotive and other applications.
CONTACT US
Corporate Headquarters
2929 South Fair Lane
Tempe, Arizona 85282
USA
By Telephone
General: 602-431-8101
Sales: & Marketing: 602-414-5109
Customer Service: 602-414-5114
Product Technical Support: 602-414-5107
By Fax
General: 602-431-2288
By E-mail:
Sales: [email protected]
Customer Service: [email protected]
Technical Support: [email protected]
ProTek Devices (Asia Pacific) Pte. Ltd.
8 Ubi Road 2, #06-19
Zervex
Singapore - 408538
Tel: +65-67488312
Fax: +65-67488313
Web
www.protekdevices.com
COPYRIGHT © ProTek Devices 1998 - This literature is subject to all applicable copyright laws and is not for resale in any manner.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice.
DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of
its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special,
consequential or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory.
PATENT INFORMATION: This device is patented under U.S. Patent No. 4,563,720
05016.R7 9/12
Page 5
www.protekdevices.com
Similar pages