PDF Data Sheet Rev. C

FEATURES
FUNCTIONAL BLOCK DIAGRAM
1.8 V to 5.5 V single supply
5 Ω (maximum) on resistance
0.75 Ω (typical) on resistance flatness
Automotive temperature range: −40°C to +125°C
–3 dB bandwidth > 200 MHz
Rail-to-rail operation
6-lead SC70 package
Fast switching times
tON = 12 ns
tOFF = 6 ns
Typical power consumption (< 0.01 μW)
TTL/CMOS compatible
ADG749
S2
D
S1
IN
SWITCH SHOWN FOR
A LOGIC 1 INPUT
02075-001
Data Sheet
CMOS 1.8 V to 5.5 V, 2.5 Ω
2:1 Mux/SPDT Switch in SC70 Package
ADG749
Figure 1.
APPLICATIONS
Battery-powered systems
Communication systems
Sample-and-hold systems
Audio signal routing
Video switching
Mechanical reed relay replacement
GENERAL DESCRIPTION
The ADG749 is a monolithic CMOS SPDT switch. This switch
is designed on a submicron process that provides low power
dissipation yet gives high switching speed, low on resistance,
and low leakage currents.
PRODUCT HIGHLIGHTS
1.
1.8 V to 5.5 V Single-Supply Operation. The ADG749
offers high performance, including low on resistance and
fast switching times, and is fully specified and guaranteed
with 3 V and 5 V supply rails.
2.
Very Low RON (5 Ω Maximum at 5 V and 10 Ω Maximum
at 3 V). At 1.8 V operation, RON is typically 40 Ω over the
temperature range.
Each switch of the ADG749 conducts equally well in both
directions when on. The ADG749 exhibits break-before-make
switching action.
3.
Automotive Temperature Range: −40°C to +125°C.
4.
On Resistance Flatness (RFLAT(ON)) (0.75 Ω typical).
Because of the advanced submicron process, −3 dB bandwidths
of greater than 200 MHz can be achieved.
5.
−3 dB Bandwidth > 200 MHz.
6.
Low Power Dissipation. CMOS construction ensures low
power dissipation.
7.
Fast tON/tOFF.
8.
Tiny, 6-lead SC70 Package.
The ADG749 can operate from a single-supply range of 1.8 V to
5.5 V, making it ideal for use in battery-powered instruments
and with the new generation of DACs and ADCs from Analog
Devices, Inc.
The ADG749 is available in a 6-lead SC70 package.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2001–2011 Analog Devices, Inc. All rights reserved.
ADG749
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Terminology .......................................................................................7
Applications ....................................................................................... 1
Typical Performance Characteristics ..............................................8
Functional Block Diagram .............................................................. 1
Test Circuits ..................................................................................... 10
General Description ......................................................................... 1
Applications Information .............................................................. 11
Product Highlights ........................................................................... 1
ADG749 Supply Voltages .......................................................... 11
Revision History ............................................................................... 2
On Response vs. Frequency ...................................................... 11
Specifications..................................................................................... 3
Off Isolation ................................................................................ 11
Absolute Maximum Ratings............................................................ 5
Outline Dimensions ....................................................................... 12
ESD Caution .................................................................................. 5
Ordering Guide .......................................................................... 12
Pin Configuration and Function Descriptions ............................. 6
REVISION HISTORY
12/11—Rev. B to Rev. C
Deleted Endnote 1 from Leakage Currents Parameter, Table 1 . 3
Deleted Endnote 1 from Leakage Currents Parameter, Table 2 . 4
10/09—Rev. A to Rev. B
Updated Format .................................................................. Universal
Added Pb-Free Information to Table 3 .......................................... 5
Added Table 4.................................................................................... 6
Updated Outline Dimensions ....................................................... 12
Changes to Ordering Guide .......................................................... 12
7/02—Rev. 0 to Rev. A.
Changes to Features.......................................................................... 1
Additions to Product Highlights .................................................... 1
Changes to Specifications ................................................................ 2
Edits to Absolute Maximum Ratings ............................................. 4
Changes to Terminology.................................................................. 4
Edits to Ordering Guide .................................................................. 4
Added new TPCs 4 and 5 ................................................................ 5
Added TPC 10 ................................................................................... 6
Test Circuits 6, 7, and 8 replaced .................................................... 7
Updated KS-6 Package Drawing..................................................... 9
1/01—Revision 0: Initial Version
Rev. C | Page 2 of 12
Data Sheet
ADG749
SPECIFICATIONS
VDD = 5 V ± 10% and GND = 0 V; TA= −40°C to +125°C unless otherwise stated.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
25°C
2.5
5
On Resistance Match Between
Channels (ΔRON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage IS (Off )
Channel On Leakage ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
DYNAMIC CHARACTERISTICS 1
tON
−40°C to +85°C
−40°C to +125°C
Unit
Test Conditions/Comments
0 V to VDD
V
Ω typ
Ω max
VS = 0 V to VDD, IS = −10 mA;
see Figure 13
6
7
0.1
0.8
0.8
1.2
1.5
0.75
±0.01
±0.25
±0.01
±0.25
8
±0.35
5
2.4
0.8
V min
V max
μA typ
μA max
VIN = VINL or VINH
±0.1
ns typ
ns max
ns typ
ns max
ns typ
ns min
dB typ
dB typ
dB typ
dB typ
MHz typ
pF typ
pF typ
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 16
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 16
RL = 300 Ω, CL = 35 pF,
VS1 = VS2 = 3 V; see Figure 17
RL = 50 Ω, CL = 5 pF, f = 10 MHz
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 18
RL = 50 Ω, CL = 5 pF, f = 10 MHz
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 19
RL = 50 Ω, CL = 5 pF; see Figure 20
6
1
Off Isolation
Channel-to-Channel Crosstalk
Bandwidth −3 dB
CS (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
−67
−87
−62
−82
200
7
27
VDD = 5.5 V
Digital inputs = 0 V or 5.5 V
0.001
1.0
1
VDD = 5.5 V
VS = 4.5 V/1 V, VD = 1 V/4.5 V;
see Figure 14
VS = VD = 1 V or VS = VD = 4.5 V;
see Figure 15
nA typ
nA max
nA typ
nA max
12
Break-Before-Make Time Delay, tD
VS = 0 V to VDD, IS = −10 mA
1
7
3
VS = 0 V to VDD, IS = −10 mA
±0.35
0.005
tOFF
Ω typ
Ω max
Ω typ
Ω max
Guaranteed by design, not subject to production test.
Rev. C | Page 3 of 12
μA typ
μA max
ADG749
Data Sheet
VDD = 3 V ± 10% and GND = 0 V; TA= −40°C to +125°C unless otherwise stated
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
25°C
−40°C to +85°C
6
7
10
On Resistance Match Between
Channels (ΔRON)
On Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage IS (Off )
Channel On Leakage ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
±0.01
±0.25
±0.01
±0.25
−40°C to +125°C
Unit
Test Conditions/Comments
0 V to VDD
V
Ω typ
Ω max
VS = 0 V to VDD, IS = –10 mA;
see Figure 13
12
0.1
0.8
2.5
0.8
±0.35
1
±0.35
5
2.0
0.8
0.005
10
15
tOFF
4
Break-Before-Make Time Delay,
8
nA typ
nA max
nA typ
nA max
VS = 0 V to VDD, IS = –10 mA
VS = 0 V to VDD, IS = –10 mA
VDD = 3.3 V
VS = 3 V/1 V, VD = 1 V/3 V;
see Figure 14
VS = VD = 1 V or VS = VD = 3 V;
see Figure 15
V min
V max
±0.1
DYNAMIC CHARACTERISTICS 1
tON
Ω typ
Ω max
Ω typ
8
μA typ
μA max
VIN = VINL or VINH
ns typ
ns max
ns typ
ns max
ns typ
RL = 300 Ω, CL = 35 pF
VS = 2 V; see Figure 16
RL = 300 Ω, CL = 35 pF
VS = 2 V; see Figure 16
RL = 300 Ω, CL = 35 pF
tD
Off Isolation
–67
–87
1
ns min
dB typ
dB typ
VS1 = VS2 = 2 V; see Figure 17
RL = 50 Ω, CL = 5 pF, f = 10 MHz
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 18
Channel-to-Channel Crosstalk
–62
–82
200
7
27
dB typ
dB typ
MHz typ
pF typ
pF typ
RL = 50 Ω, CL = 5 pF, f = 10 MHz
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 19
RL = 50 Ω, CL = 5 pF; see Figure 20
Bandwidth −3 dB
CS (Off )
CD, CS (On)
POWER REQUIREMENTS
IDD
VDD = 3.3 V
Digital inputs = 0 V or 3.3 V
0.001
1.0
1
Guaranteed by design, not subject to production test.
Rev. C | Page 4 of 12
μA typ
μA max
Data Sheet
ADG749
ABSOLUTE MAXIMUM RATINGS
TA = 25°C unless otherwise noted.
Table 3.
Parameter
VDD to GND
Analog, Digital Input 1
Peak Current, S or D
Continuous Current, S or D
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Junction Temperature
SC70 Package, Power
Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
Pb-free Reflow Soldering
Peak Temperature
Time at Peak Temperature
1
Ratings
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V or 30 mA,
whichever occurs first
100 mA (pulsed at 1 ms, 10%
duty cycle max)
30 mA
−40°C to +125°C
−65°C to +150°C
150°C
315 mW
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating can be applied at any
one time.
ESD CAUTION
332°C/W
120°C/W
215°C
220°C
260(+0/–5)°C
10 sec to 40 sec
Overvoltage at IN, S or D will be clamped by internal diodes. Current should
be limited to the maximum ratings given.
Rev. C | Page 5 of 12
ADG749
Data Sheet
IN 1
VDD
2
GND
3
ADG749
TOP VIEW
(Not to Scale)
6
S2
5
D
4
S1
02075-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin Number
1
2
3
4
5
6
Mnemonic
IN
VDD
GND
S1
D
S2
Description
Digital control input pin.
Most positive power supply pin.
Ground (0 V) reference pin.
Source terminal of the multiplexer. Can be used as input or output.
Drain terminal of the multiplexer. Can be used as input or output.
Source terminal of the multiplexer. Can be used as input or output.
Table 5. Truth Table
ADG749 IN
0
1
Switch S1
ON
OFF
Switch S2
OFF
ON
Rev. C | Page 6 of 12
Data Sheet
ADG749
TERMINOLOGY
tON
Delay between applying the digital control input and the output
switching on.
RON
Ohmic resistance between D and S.
ΔRON
On resistance match between any two channels, such as: RON
max − RON min.
tOFF
Delay between applying the digital control input and the output
switching off.
RFLAT(ON)
Flatness is defined as the difference between the maximum and
minimum value of on resistance as measured over the specified
analog signal range.
tD
Off time or on time measured between the 90% points of both
switches, when switching from one address state to another.
IS (Off)
Source leakage current with the switch off.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance.
ID, IS (On)
Channel leakage current with the switch on.
VD (VS)
Analog voltage on Terminals D and S.
CS (Off)
Off switch source capacitance.
CD, CS (On)
On switch capacitance.
Off Isolation
A measure of unwanted signal coupling through an off switch.
Bandwidth
The frequency at which the output is attenuated by −3 dBs.
On Response
The frequency response of the on switch.
Insertion Loss
Loss due to on resistance of the switch.
Rev. C | Page 7 of 12
ADG749
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
0.15
6.0
TA = 25°C
VDD = 2.7V
5.5
VDD = 5V
VD = 4.5V/1V
VS = 1V, 4.5V
5.0
4.5
0.10
VDD = 4.5V
VDD = 3.0V
3.5
CURRENT (nA)
3.0
2.5
VDD = 5.0V
2.0
1.5
0.05
ID, IS (ON)
0
1.0
IS (OFF)
02075-003
0.5
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
02075-006
RON (Ω)
4.0
–0.05
5.0
0
10
20
VD OR VS, DRAIN OR SOURCE VOLTAGE (V)
30
40
50
60
70
80
90
80
90
TEMPERATURE (°C)
Figure 3. On Resistance vs. VD (VS) Single Supplies
Figure 6. Leakage Currents vs. Temperature
6.0
0.15
VDD = 3V
5.5
5.0
VDD = 3V
VD = 3V/1V
VS = 1V, 3V
+85°C
4.5
0.10
+25°C
CURRENT (nA)
4.0
3.0
2.5
2.0
1.5
0.05
ID, IS (ON)
0
1.0
IS (OFF)
02075-004
0.5
0
0
0.5
1.0
1.5
2.0
2.5
02075-007
RON (Ω)
–40°C
3.5
–0.05
3.0
0
10
20
VD OR VS, DRAIN OR SOURCE VOLTAGE (V)
30
40
50
60
70
TEMPERATURE (°C)
Figure 4. On Resistance vs. VD (VS) for Different Temperature, VDD = 3 V
Figure 7. Leakage Currents vs. Temperature
6.0
10m
VDD = 5V
5.5
VDD = 5V
1m
5.0
4.5
100µ
+85°C
3.0
2.5
+25°C
2.0
–40°C
1.0
10n
02075-005
0.5
0
0.5
1.0
1.5
2.0
2.5
1µ
100n
1.5
0
10µ
3.0
3.5
4.0
4.5
02075-008
3.5
ISUPPLY (A)
RON (Ω)
4.0
1n
5.0
1
VD OR VS, DRAIN OR SOURCE VOLTAGE (V)
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 5. On Resistance vs. VD (VS) for Different Temperatures, VDD = 5 V
Rev. C | Page 8 of 12
Figure 8. Supply Current vs. Input Switching Frequency
100M
Data Sheet
ADG749
–30
0
VDD = 5V, 3V
VDD = 5V
–40
–60
ON RESPONSE (dB)
OFF ISOLATION (dB)
–50
–70
–80
–90
–100
–2
–4
–120
–130
10k
100k
1M
10M
–6
10k
100M
02075-011
02075-009
–110
100k
FREQUENCY (Hz)
1M
10M
100M
FREQUENCY (Hz)
Figure 9. Off Isolation vs. Frequency
Figure 11. On Response vs. Frequency
12
–30
VDD = 5V, 3V
–40
10
–50
VDD = 5V
8
6
QINJ (pC)
–70
–80
–90
VDD = 3V
4
2
–100
0
–110
100k
1M
10M
02075-012
–120
–130
10k
–2
02075-010
CROSSTALK (dB)
–60
–4
0
100M
1
2
3
4
VS (V)
FREQUENCY (Hz)
Figure 10. Crosstalk vs. Frequency
Figure 12. Charge Injection vs. Source Voltage
Rev. C | Page 9 of 12
5
ADG749
Data Sheet
TEST CIRCUITS
S
A
VD
VS
V1
S
ID (OFF)
D
D
ID (ON)
A
VD
VS
02075-015
S
A
02075-014
IS (OFF)
IDS
D
02075-013
VS
RON = V1/IDS
Figure 14. Off Leakage
Figure 13. On Resistance
0.1µF
VDD
VDD
S
VS
Figure 15. On Leakage
VIN
50%
VOUT
D
RL
300Ω
IN
50%
90%
90%
VOUT
CL
35pF
tON
tOFF
02075-016
GND
Figure 16. Switching Times
0.1µF
VDD
S1
VS1
VDD
VIN
VOUT
D2
S2
VS2
RL2
300Ω
IN
VIN
CL2
35pF
VOUT
50%
0V
50%
50%
50%
0V
tD
tD
02075-017
GND
Figure 17. Break-Before-Make Time Delay, tD
NETWORK
ANALYZER
VDD
50Ω
S
IN
50Ω
0.1µF
VOUT RL
50Ω
VS
D
D
VOUT
VS
Figure 18. Off Isolation
50Ω
VOUT
VS
02075-018
OFF ISOLATION = 20 log
RL
50Ω
VDD
IN
CROSSTALK = 20 log
50Ω
S
S2
GND
NETWORK
ANALYZER
S1
IN
R
50Ω
GND
GND
CHANNEL-TO-CHANNEL
VOUT
VS
Figure 19. Channel-to-Channel Crosstalk
Rev. C | Page 10 of 12
VS
D
VIN
02075-019
NETWORK
ANALYZER
VDD
VIN
VDD
VDD
0.1µF
INSERTION LOSS = 20 log
RL
50Ω
VOUT
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Figure 20. Bandwidth
02075-020
VDD
0.1µF
Data Sheet
ADG749
APPLICATIONS INFORMATION
The ADG749 belongs to Analog Devices’ new family of CMOS
switches. This series of general-purpose switches has improved
switching times, offering lower on resistance, higher bandwidths, low power consumption, and low leakage currents.
ADG749 SUPPLY VOLTAGES
Functionality of the ADG749 extends from 1.8 V to 5.5 V single
supply, which makes it ideal for battery-powered instruments,
where power efficiency and performance are important design
parameters.
It is important to note that the supply voltage affects the input
signal range, the on resistance, and the switching times of the
part. By taking a look at the typical performance characteristics
and the specifications, the effects of the power supplies can be
clearly seen.
For VDD = 1.8 V operation, RON is typically 40 Ω over the
temperature range.
zero in the numerator of the transfer function A(s). Because the
switch on resistance is small, this zero usually occurs at high
frequencies. The bandwidth is a function of the switch output
capacitance combined with CDS and the load capacitance. The
frequency pole corresponding to these capacitances appears in
the denominator of A(s).
The dominant effect of the output capacitance, CD, causes the
pole breakpoint frequency to occur first. Therefore, in order
to maximize bandwidth, a switch must have a low input and
output capacitance and low on resistance. The on response vs.
frequency plot for the ADG749 is shown in Figure 11.
OFF ISOLATION
Off isolation is a measure of the input signal coupled through
an off switch to the switch output. The capacitance, CDS, couples
the input signal to the output load when the switch is off, as
shown in Figure 22.
ON RESPONSE VS. FREQUENCY
CDS
CDS
D
S
VIN
CD
CLOAD
RLOAD
02075-021
VOUT
RON
Figure 21. Switch Represented by Equivalent Parasitic Components
The transfer function that describes the equivalent diagram of
the switch (Figure 21) is of the form A(s) shown below.
 s (RON CDS ) + 1 
A(s) = RT 

 s (RT RON CDS ) + 1 
where:
D
S
Figure 21 illustrates the parasitic components that affect the
ac performance of CMOS switches (the switch is shown
surrounded by a box). Additional external capacitances will
further degrade some performance. These capacitances affect
feedthrough, crosstalk, and system bandwidth.
VIN
CLOAD
RLOAD
02075-022
VOUT
CD
Figure 22. Off Isolation is Affected by External Load Resistance
and Capacitance
The larger the value of CDS, the larger the values of feedthrough that will be produced. The typical performance
characteristic graph of Figure 9 illustrates the drop in off
isolation as a function of frequency. From dc to roughly
200 kHz, the switch shows better than −95 dB isolation. Up to
frequencies of 10 MHz, the off isolation remains better than
−67 dB. As the frequency increases, more and more of the input
signal is coupled through to the output. Off isolation can be
maximized by choosing a switch with the smallest CDS possible.
The values of load resistance and capacitance also affect off
isolation, since they contribute to the coefficients of the poles
and zeros in the transfer function of the switch when open.


s (RLOAD CDS )
A(s) = 

 s (RLOAD ) (CLOAD + CD + CDS ) + 1 
RT = RLOAD/(RLOAD + RON)
CT = CLOAD + CD + CDS
The signal transfer characteristic is dependent on the switch
channel capacitance, CDS. This capacitance creates a frequency
Rev. C | Page 11 of 12
ADG749
Data Sheet
OUTLINE DIMENSIONS
2.20
2.00
1.80
6
5
4
1
2
3
0.65 BSC
1.30 BSC
1.00
0.90
0.70
0.10 MAX
COPLANARITY
0.10
2.40
2.10
1.80
1.10
0.80
0.30
0.15
SEATING
PLANE
0.40
0.10
0.22
0.08
0.46
0.36
0.26
COMPLIANT TO JEDEC STANDARDS MO-203-AB
072809-A
1.35
1.25
1.15
Figure 23. 6-Lead Thin Shrink Small Outline Transistor Package [SC70]
(KS-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADG749BKSZ-R2
ADG749BKSZ-REEL
ADG749BKSZ-REEL7
1
2
Temperature range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
6-Lead Thin Shrink Small Outline Transistor Package [SC70]
Z= RoHS Compliant Part.
Branding on this package is limited to three characters due to space constraints.
©2001–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02075-0-12/11(C)
Rev. C | Page 12 of 12
Package Option
KS-6
KS-6
KS-6
Branding 2
S1M
S1M
S1M