CSM1800 High Speed Optocoupler

ISOCOM LTD
®
PART NUMBER
CSM1800/1801/L2S
COMPONENT
ISSUE 1
SPECIFICATION
September 2013
Component Specification
For Ceramic Hermetically Sealed, Radiation Hard
High Speed Optocoupler
M1077 IECQ
Further copies of this document may be obtained from:
ISOCOM LIMITED
WASHINGTON, UK
NE38 0AH
www.isocom.uk.com
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 1 of 10
ISOCOM LTD
®
Ceramic Hermetically Sealed, Radiation Hard
High Speed Optocoupler
■ CSM1800/1801
■ CSM1800/1801/L2
■ CSM1800/1801/L2S
Features
Applications
▪ Released to European Standard
and Complies to Mil Std
▪ Space Radiation Equipment
▪ Military, high reliability system
▪ Total Ionizing Dose Tested to 1MRad(si)
▪ Medical instruments
▪ Displacement Damage Tested to 3 MEV x10¹²
▪ Mos, Cmos Applications
▪ Hermetically Sealed
▪ Logic Interfacing
▪ High Isolation Voltage
▪ Data Transmission
▪ 6 Pin LCC Package
▪ Power Supply
▪ Low Input Requirements
▪ Modems
▪ High Speed; Typically 2Mhz
Description
These devices are single, hermetically sealed optically coupled isolators. Each channel is composed of a Gallium
Arsenide infra-red emitting diode and a silicon phototransistor. The CSM1800 series are being used in environments
encounted by space applications. It is manufactured to meet the JANS standard in conjunction with MIL-PRF-19500
procedures (please see next page for all other applicable specifications). Package styles for this device include 6 Pin
LCC Package with surface mount, solder dip option available. These packages have a shield effect to cut off ambient light
as they are designed for high density mounting applications.
Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance
characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 2 of 10
ISOCOM LTD
®
Standards
The following specifications have been included in the manufacturing of this product:
Military Compliance Specifications
MIL-PRF-19500 – General Specification for Discrete Semiconductor Devices
IECQ – M1077
Military Compliance Standards
MIL-STD-202 – Test Method Standard Electronic and Electrical Component Parts
MIL-STD-883 – Test Method Standard Microcircuits
MIL-STD-750 – Test Methods for Semiconductor Devices
ISO 9001:2008 – Manufacturing of Optocouplers and Optoelectronic components.
Single Channel Schematic
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 3 of 10
ISOCOM LTD
®
Selection Guide Package Styles and Configuration Options
Package
6 pin LCC
Lead Style
Channels
Common Channel Wiring
Isocom Part Number and Options
Commercial
Defense Screen Level
Space Screen Level
Standard Gold Plate Finish
Solder Dipped
1
CSM1800/1801
CSM1800/1801/L2
CSM1800/1801/L2S
Gold Plate
Option 20
Functional Diagrams
CSM1800/1801
6 pin LCC
1 Channel
Device Marking
ISOCOM
XXXXXXX
XXXX
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 4 of 10
Manufacturer
Isocom Part Number
Date Code (XX year XX week)
ISOCOM LTD
®
Outline Drawings
Absolute Maximum Ratings
TA = 25°C U.O.S.
Storage Temperature
Operating Temperature
Lead Soldering Temperature
Input-to-Output Isolation Voltage
-65°C to +150°C
-55°C to +125°C
260°C 1.6mm from case for 10S
1500VDC
Input Diode
Average Forward Current
Reverse Voltage
Peak forward Current
Power Dissipation
20mA
7V
40mA
36mW
1mS,
Output Transistor
Supply Voltage
Average Current
Collector Current
Power Dissipation
0.5V to 20V
8mA
16mA
50mW
Electrical Characteristics
Input Diode Electrical Characteristics TA = 25°C U.O.S.
Parameter
Symbol
Test Conditions
Current Transfer Ratio
hf (CTR)
Logic low output voltage
Logic high output current
Logic high supply current
VOL
IoH
ICCH
Logic low supply current
ICCL
Input forward voltage
Input reverse breakdown
Input-Output Insulation
Leakage Current
Propagation Delay
H-L
Propagation Delay
L-H
VF
VBR
Vcc =4.5V, Vo=0.4V
IF = 16mA, TA =25°C
Vcc =4.5V, IF = 16mA, Io=1.44mA
IF = 0, Vo= Vcc=15V
IF = 0, Vo= OPEN
Vcc=15V
Vcc=15V, IF = 16mA
IF = 0
IF = 16mA
IR = 10µA
RH = 45%, TA = 25°C, t = 5S
VIO = 1500VDC
IIO
tPHL
tPLH
RL = 1.9KOhms
Vcc = 5V
IF = 16mA
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 5 of 10
Min
-
Type
Max
Units
17
-
%
-
0.3
0.05
0.05
0.4
250
5
V
µA
µA
-
60
400
µA
3
1.45
12
1.7
1.0
V
V
µA
-
0.3
0.8
µS
-
0.1
0.8
µS
ISOCOM LTD
®
Electrical Characteristics
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 6 of 10
ISOCOM LTD
®
GROUP TESTING to MIL-STD 750
GROUP
Group A
SG1
SG2
SG3
SG4
Group B
SG 1
SG 2
SG 3
TEST
MIL-STD-750
Visual inspection & mechanical
dimensions
DC static test at 25°C
DC static test at 125°C and ‐55°C
Dynamic test at 25°C
Method 2071
Physical dimensions
Solderability
Resistance to solvents
Thermal Shock
Electrical measurement
Bond strength
Acc. steady‐state operation life
Method 2066
Method 2026
Method 1022
Method 1056 Cond. B,
25 cycles
Method 1051, 100
cycles, -55/+125°C
Method 1071, Cond. H
(fine), Cond. C (gross)
pre and post
2075
Method 2037, Cond. D
Method 2017
Method 1037, 1042,
Cond D, Tab.5-5
Method 1071, Cond. H
(fine), Cond. C (gross)
pre and post
Method 2037, Cond. D
Method 1027
Electrical measurement
Bond strength
pre and post
Method 2037, Cond. D
Thermal Shock
Method 1056, Cond. B,
25 shocks
Method 1051, Cond. C,
‐55/+125°C , 25 cycles
(total 45 cycles
including screening)
Method 1071, Cond. H
(fine), Cond. C (gross)
Method 1021
pre and post
Method 2016,
non‐operating, 1500 G,
0.5 ms, 5 blows in each
orientation (X1,Y1,Z1)
Method 2056
Method 2006, at a peak
level of 5000 G
pre and post
Temperature cycling
Hermetic seal fine and gross leak
SG 4
Electrical measurement
Decap internal visual inspection
Bond strength
Die shear
Intermittent operation life
Hermetic seal fine and gross leak
SG 5
Group C
SG 2
Temperature cycling
Hermetic seal fine and gross leak
SG 3
Moisture resistance
Electrical measurement
Mechanical shock
Vibration
Constant acceleration
SG 6
Electrical measurement
Steady state operating life Not
required as B5 is available on same
lot
yes
yes
yes
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 7 of 10
READ AND
RECORD
yes
yes
yes
yes
yes
yes
yes
yes
yes
ISOCOM LTD
®
100% SCREENING to MIL-STD 750
TEST
MIL-STD-750
Internal Visual
2072
READ AND RECORD?
Sealing
(Fine Leak)
(Gross Leak)
Temp Cycling
Const. Acceler
PIND
Radiography
Initial Electrical
HTRB
Interim Electrical
Burn-In
Final Electrical
PDA
(Fine Leak)
(Gross Leak)
1071, Condition H1
1071, Condition C
1051, Condition
B‐55/+125°C, 20 Cycles.
2006, 5000G, Y1 only.
2052, Condition A
2076
125°C, ‐55°C, 25°C
1039
25°C only
1039
125°C, ‐55°C, 25°C
Max. 5%, pre/post B1
electrical and delta at RT
only
1071, Condition H1
1071, Condition C
Solder Dip
Fine Leak
Gross Leak
1071, Condition H1
1071, Condition C
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 8 of 10
R&R
R&R
R&R
Calculate & R
ISOCOM LTD
®
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 9 of 10
ISOCOM LTD
®
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 10 of 10
ISOCOM LTD
®
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 11 of 10
Similar pages