WT51F116/108 Starter Kit Board Operation Manual WT51F116/108 EVB Starter Kit Board Operation Manual REV. 1.0 September 24, 2014 本文件為偉詮電子股份有限公司機密資料 , 未經許可不得擅自複印或備份。 WT51F116/108 Starter Kit Board Operation Manual Ver. 1.0 Date 2014/09/24 Applicant Louis 1st version This document is Weltrend confidential information. Do not copy. 2 Description WT51F116/108 Starter Kit Board Operation Manual Table of contents CHAPTER 1 WT51F116/108 STARTER KIT BOARD HARDWARE DESCRIPTION..................................................4 1.1 SYSTEM BLOCK DIAGRAM ......................................................................................................................................4 1.2 STARTER KIT BOARD COMPONENTS LOCATION .......................................................................................................5 CHAPTER 2 2.1 2.2 2.3 2.4 DC INPUT CONNECTOR (J1)...................................................................................................................................6 SWUT (SINGLE-WIRE UART) PROGRAMMING INTERFACE PORT (J2) ......................................................................6 WT51F116/108 I2C INTERFACE PORT ...................................................................................................................7 TESTING PINS (J6/J7)............................................................................................................................................8 CHAPTER 3 3.1 3.2 3.3 3.4 WT51F116/108 STARTER KIT BOARD I/O PORT DESCRIPTION........................................................6 WT51F116/108 STARTER KIT BOARD CIRCUIT DESCRIPTION.........................................................9 VDD POWER SELECTION .......................................................................................................................................9 POWER CIRCUIT.....................................................................................................................................................9 RESET CIRCUIT .................................................................................................................................................10 OSCILLATE CIRCUIT .............................................................................................................................................10 CHAPTER 4 WT51F116/108 STARTER KIT BOARD OPERATION MANUAL ..........................................................11 4.1 WT51F116/108 TESTING AND DEMO PLATFORM ...................................................................................................11 4.2 LED DISPLAY ......................................................................................................................................................12 CHAPTER 5 DRIVER MODULE.........................................................................................................................................13 5.1 DRIVER MODULE SUMMARY .................................................................................................................................13 5.2 MAIN PROGRAM <MAIN.C> ..................................................................................................................................13 CHAPTER 6 APPENDIX......................................................................................................................................................14 6.1 CIRCUIT ..............................................................................................................................................................14 6.2 BOM ..................................................................................................................................................................16 6.3 ORDERING INFORMATION .....................................................................................................................................17 This document is Weltrend confidential information. Do not copy. 3 WT51F116/108 Starter Kit Board Operation Manual Chapter 1 1.1 WT51F116/108 Starter Kit Board Hardware Description System Block Diagram WT51F116/108 is an enhanced 8052 Micro Controller with LCD Driver functions, and the Starter Kit Board is designed for 32-pin QFN type IC to demonstrate its functions. System structure is as the figure below. VDD VDD 47uF SCL I2C SDA 0.1uF WT51F116/108 20pF OSCI 12MHz 5V OSCO 20pF LED GPIOB0 GPIOB1 VDD GPIOB2 10K RST / SWUT 4.7uF GPIOB3 GPIOB4 GPIOB5 SWUT AD_ADJ ADC 2 5V VR This document is Weltrend confidential information. Do not copy. 4 WT51F116/108 Starter Kit Board Operation Manual 1.2 Starter Kit Board Components Location Testing Area LED Display Area J3 External Reset Pin / SWUT Option Jump U1 WT51F116/108 J2 Single-wire Programming Interface Port SWB1 Reset Key J1 DC 5 V Power J5 I2C Port J6/ J7 WT51F116/108 Test Pin This document is Weltrend confidential information. Do not copy. 5 VR1 Adjust AD Voltage VR WT51F116/108 Starter Kit Board Operation Manual Chapter 2 2.1 WT51F116/108 Starter Kit Board I/O Port Description DC Input Connector (J1) This is DC input connector for Starter Kit Board (supporting voltage: DC 5V). 2.2 Pad Number Description 1 Positive Input Pin 2 -- 3 Negative Input Pin SWUT (Single-wire UART) Programming Interface Port (J2) WT51F116/108 Single-wire programming port as below: Pitch (1.25 mm) This document is Weltrend confidential information. Do not copy. 6 WT51F116/108 Starter Kit Board Operation Manual 2.3 Pad Number Description 1 VDD 2 SWUT 3 GND WT51F116/108 I2C Interface Port Components Location (J5): Slave I2C Interface Port. Pitch (1.25 mm) Pad Number Description 1 VDD 2 Slave_SCL 3 Slave_SDA 4 GND This document is Weltrend confidential information. Do not copy. 7 WT51F116/108 Starter Kit Board Operation Manual 2.4 Testing Pins (J6/J7) These are testing signal pins. Pitch (2.54 mm) J6 J7 Pad Number Description Pad Number Description 1-2 GPIOA5DH/IRQ15/ADC15/OSCI/PWM1B/P00 1-2 GPIOC2D/ PWM2C/P06 3-4 GPIOA4DH/IRQ14/ADC14/OSCO/PWM0B/P01 3-4 GPIOC1D/IRQ7/ADC7/P05 5-6 GPIOB5D/IRQ12/ADC12/RXA/PWM1A/P02 5-6 GPIOC0D/IRQ6/ADC6/PWM3B/P04 7-8 GPIOB4D/IRQ11/ADC11/TXA/PWM1D/P03 7-8 GPIOB2D/IRQ5/ADC5/STB/PWM0D 9-10 GPIOB3D/IRQ10/ADC10/PWM0A 9-10 GPIOB1D/IRQ4/ADC4/MOSI/PWM3A 11-12 GPIOC5D/IRQ9/ADC9 11-12 GPIOB0D/IRQ3/ADC3/PWM2A 13-14 GPIOC4D/IRQ8/ADC8 13-14 GPIOA2DH/IRQ2/ADC2/CMPO/PWM1C 15-16 GPIOC3D/PWM3C/P07 15-16 GPIOA1DHIRQ1/ADC1/VREF/CMPN/SCKA/ MISOB/RXA/SCL/PWM2B 17-18 GPIOA7DH 17-18 GPIOD5 19-20 GPIOA6DH 19-20 GPIOD4 21-22 GPIOB7D 21-22 GPIOA0DH//IRQ0/ADC0/CMPP/MISOA/ SCKB/TXA/SDA/PWM0D 23-24 GPIOB6D 23-24 VSS 25-26 GPIOC7D 25-26 VDD 27-28 GPIOC6D 27-28 GPIA3D/IRQ13/ADC13/NRST/SWUT 29-30 GPIOD1 29-30 GPIOD3 31-32 GPIOD0 31-32 GPIOD2 This document is Weltrend confidential information. Do not copy. 8 WT51F116/108 Starter Kit Board Operation Manual Chapter 3 3.1 WT51F116/108 Starter Kit Board Circuit Description VDD Power Selection There are three main power options for WT51F116/108 Starter Kit Board. (External power input cannot exceed Max. 5.5V as spec definition). 1. 5V adapter, J1 DC Jack (VDD). 2. External VDD: PO1 positive input, PO2 negative power, external VDD cannot exceed Max 5.5V as spec definition. 3. WLINK-SWUT VDD: Using WLINK-SWUT VDD supplies WT51F116/108 VDD power. If power works normally, DB1 LED will light up. 3.2 Power circuit VDD power input should be with filter capacitance, this is best that the layout is close to the pin. This document is Weltrend confidential information. Do not copy. 9 WT51F116/108 Starter Kit Board Operation Manual 3.3 RESET Circuit WT51F116/108 RESET circuit and SWUT (Single-wire programming) use the same pin, the related circuit description as below. When SWUT on programming, J3 JUMP should be removed, and disconnect from the external RC RESET. After programming finished, J2 JUMP should be plugged back, if the REST function had been used. 3.4 Oscillate Circuit WT51F116/108 oscillates circuit as bellow: This document is Weltrend confidential information. Do not copy. 10 WT51F116/108 Starter Kit Board Operation Manual Chapter 4 4.1 WT51F116/108 Starter Kit Board Operation Manual WT51F116/108 testing and demo platform WT51F116/108 Starter Kit Board built in a single and easy led flash to display functions, and reserved some pins for testing usage. Add Function Testing Area WT51F116 /108 Test Pin 5V Power Indicator WT51F116 /108 Reset key DC 5V Input AD Voltage LED Indicator Adjust Button (VR1) This document is Weltrend confidential information. Do not copy. 11 WT51F116/108 Starter Kit Board Operation Manual 4.2 LED display After Power on, LED will alternately blink on the EVB board. Meanwhile, adjusting VR1 can change LED blinking speed. LED Indicator This document is Weltrend confidential information. Do not copy. 12 AD Voltage Adjust Button (VR1) WT51F116/108 Starter Kit Board Operation Manual Chapter 5 5.1 Driver Module Driver Module Summary Please refer to the Driver module display, as below: 5.2 Main Program <Main.c> Function Description void INIT_LED(void) Initialize “LED port” (Driver layer) void LED_SHIFT (void) Rotate “LED” light (Application layer) This document is Weltrend confidential information. Do not copy. 13 WT51F116/108 Starter Kit Board Operation Manual Chapter 6 6.1 Appendix Circuit 1. Power This document is Weltrend confidential information. Do not copy. 14 WT51F116/108 Starter Kit Board Operation Manual 2. WT51F116/108 (MCU) This document is Weltrend confidential information. Do not copy. 15 WT51F116/108 Starter Kit Board Operation Manual 6.2 BOM This document is Weltrend confidential information. Do not copy. 16 WT51F116/108 Starter Kit Board Operation Manual 6.3 Ordering Information 1. WT51F116/108 Development Kit Kit WT51F116/108 Development Kit Product Name Number Single-wire Programming Board PL-2303 (WLINK-SWUT) x 1 WA000 Simple Version (WT51F116/108 Starter Kit Board) x 1 WB010 SWUT Programming Wire x 1 2. WT51F116/108 Starter Kit Board (Simple Version) Kit WT51F116/108 Simple Version 3. Product Name Number Simple Version (WT51F116/108 Starter Kit Board) WB010 EVB Operation Manual DOC28 Single-wire Programming Board (WLINK-SWUT) Kit Single-wire Programming Board WLINK-SWUT Product Name Number Single-wire Programming Board PL-2303 (WLINK-SWUT) WA000 WLINK-SWUT Operation Manual DOC2 This document is Weltrend confidential information. Do not copy. 17