INFINEON TDK5100

Wireless Components
ASK/FSK Transmitter 868/433 MHz
TDK 5100 Version 1.0
Specification October 2002
Preliminary
Preliminary
Revision History
Current Version: Version 1.0 as of 31.10.2002
Previous Version: Version 0.1 as of 19.04.2002
Page
(in previous
Version)
Page
(in current
Version)
Subjects (major changes since last revision)
5-2
4-2
ESD-specification added
5-3, 5-6
4-3, 4-6
VCO-frequency range specified
5-4, 5-7
4-4, 4-7
Tolerances of Lcosc specified
Value of Iclkout corrected
5-5, 5-8
4-5, 4-8
Tolerances of output power specified
ABM®, AOP®, ARCOFI®, ARCOFI®-BA, ARCOFI®-SP, DigiTape®, EPIC®-1, EPIC®-S, ELIC®, FALC®54, FALC®56, FALC®-E1, FALC®-LH, IDEC®, IOM®,
IOM®-1, IOM®-2, IPAT®-2, ISAC®-P, ISAC®-S, ISAC®-S TE, ISAC®-P TE, ITAC®, IWE®, MUSAC®-A, OCTAT®-P, QUAT®-S, SICAT®, SICOFI®, SICOFI®2, SICOFI®-4, SICOFI®-4µC, SLICOFI® are registered trademarks of Infineon Technologies AG.
Edition 31.10.2002
Published by Infineon Technologies AG,
Balanstraße 73,
81541 München
© Infineon Technologies AG 2002.
All Rights Reserved.
Attention please!
As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and circuits implemented within components or assemblies.
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved.
Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest
Infineon Technologies Office.
Infineon Technologies AG is an approved CECC manufacturer.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing
material back, if it is sorted. You must bear the costs of transport.
For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose!
Critical components1 of the Infineon Technologies AG, may only be used in life-support devices or systems2 with the express written approval of the
Infineon Technologies AG.
1 A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that lifesupport device or system, or to affect its safety or effectiveness of that device or system.
2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they
fail, it is reasonable to assume that the health of the user may be endangered.
TDK 5100
Product Info
Product Info
General Description
Features
Applications
Ordering Information
The TDK 5100 is a single chip ASK/ Package
FSK transmitter for the frequency
bands 433-435 and 868-870 MHz. The
IC offers a high level of integration and
needs only a few external components.
The device contains a fully integrated
PLL synthesizer and a high efficiency
power amplifier to drive a loop antenna.
A special circuit design and an unique
power amplifier design are used to
save current consumption and therefore to save battery life. Additionally
features like a power down mode, a low
power detect, a selectable crystal oscillator frequency and a divided clock output are implemented. The IC can be
used for both ASK and FSK modulation.
■
temperature range −40 ... +125°C
■
power down mode
■
low voltage sensor
■
selectable crystal oscillator
6.78 MHz / 13.56 MHz
■
programmable divided clock output
for µC
■
low external component count
Keyless entry systems
■
Alarm systems
Remote control systems
■
Communication systems
■
fully integrated frequency synthesizer
■
VCO without external components
■
ASK and FSK modulation
■
switchable frequency range
433-435 MHz / 868-870 MHz
■
high efficiency power amplifier
(typically 5 dBm / 2 dBm)
■
low supply current (typically 7mA)
■
voltage supply range 2.1 - 4 V
■
■
Type
Ordering Code
Package
TDK 5100
Q67100-H2060
P-TSSOP-16
available on tape and reel
Wireless Components
Product Info
Specification, October 2002
1
Product Description
Contents of this Chapter
1.1
1.2
1.3
1.4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
TDK 5100
Product Description
1.1 Overview
The TDK 5100 is a single chip ASK/FSK transmitter for the frequency bands
433-435 MHz and 868-870 MHz. The IC offers a high level of integration and
needs only a few external components. The device contains a fully integrated
PLL synthesizer and a high efficiency power amplifier to drive a loop antenna.
A special circuit design and an unique power amplifier design are used to save
current consumption and therefore to save battery life. Additional features like
a power down mode, a low power detect, a selectable crystal oscillator frequency and a divided clock output are implemented. The IC can be used for
both ASK and FSK modulation.
1.2 Applications
■
Keyless entry systems
■
Remote control systems
■
Alarm systems
■
Communication systems
1.3 Features
Wireless Components
■
fully integrated frequency synthesizer
■
VCO without external components
■
ASK and FSK modulation
■
switchable frequency range 433-435 MHz / 868-870 MHz
■
high efficiency power amplifier (typically 5 dBm / 2 dBm)
■
low supply current (typically 7 mA)
■
voltage supply range 2.1 - 4 V
■
temperature range −40°C ... 125°C
■
power down mode
■
low voltage sensor
■
selectable crystal oscillator 6.78 MHz / 13.56 MHz
■
programmable divided clock output for µC
■
low external component count
1-2
Specification, October 2002
TDK 5100
Product Description
1.4 Package Outlines
Figure 1-1
Wireless Components
P-TSSOP-16
1-3
Specification, October 2002
2
Functional Description
Contents of this Chapter
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.5.1
2.4.5.2
2.4.5.3
2.4.6
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Functional Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Functional Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
PLL Synthesizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Low Power Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Power Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Power Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
PLL Enable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Transmit Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Recommended timing diagrams for ASK- and FSK-Modulation . . 2-12
TDK 5100
Functional Description
2.1 Pin Configuration
PDWN
1
16
CSEL
LPD
2
15
FSEL
VS
3
14
PAOUT
LF
4
13
PAGND
GND
5
12
FSKGND
ASKDTA
6
11
FSKOUT
FSKDTA
7
10
COSC
CLKOUT
8
9
TDK 5100
CLKDIV
Pin_config.wmf
Figure 2-1
IC Pin Configuration
Table 2-1
Wireless Components
Pin No.
Symbol
Function
1
PDWN
Power Down Mode Control
2
LPD
Low Power Detect Output
3
VS
Voltage Supply
4
LF
Loop Filter
5
GND
6
ASKDTA
Amplitude Shift Keying Data Input
7
FSKDTA
Frequency Shift Keying Data Input
8
CLKOUT
Clock Driver Output
9
CLKDIV
Clock Divider Control (847.5 kHz or 3.34 MHz)
10
COSC
11
FSKOUT
Frequency Shift Keying Switch Output
12
FSKGND
Frequency Shift Keying Ground
13
PAGND
Power Amplifier Ground
14
PAOUT
Power Amplifier Output
15
FSEL
Frequency Range Selection (433 or 868 MHz)
16
CSEL
Crystal Frequency Selection (6.78 or 13.56 MHz)
Ground
Crystal Oscillator Input
2-2
Specification, October 2002
TDK 5100
Functional Description
2.2 Pin Definitions and Functions
Table 2-2
Pin
No.
Symbol
1
PDWN
Function
Interface Schematic1)
Disable pin for the complete transmitter circuit.
VS
40 µA ∗ (ASKDTA+FSKDTA)
A logic low (PDWN < 0.7 V) turns off all
transmitter functions.
5 kΩ
A logic high (PDWN > 1.5 V) gives access to
all transmitter functions.
1
"ON"
150 kΩ
PDWN input will be pulled up by 40 µA internally by either setting FSKDTA or ASKDTA
to a logic high-state.
250 kΩ
2
LPD
This pin provides an output indicating the
low-voltage state of the supply voltage VS.
VS
VS < 2.15 V will set LPD to the low-state.
40 µA
2
300 Ω
3
VS
Wireless Components
An internal pull-up current of 40 µA gives the
output a high-state at supply voltages above
2.15 V.
This pin is the positive supply of the transmitter electronics.
An RF bypass capacitor should be connected directly to this pin and returned to
GND (pin 5) as short as possible.
2-3
Specification, October 2002
TDK 5100
Functional Description
4
LF
Output of the charge pump and input of the
VCO control voltage.
The loop bandwidth of the PLL is 150 kHz
when only the internal loop filter is used.
The loop bandwidth may be reduced by
applying an external RC network referencing
to the positive supply VS (pin 3).
VS
140 pF
15 pF
35 kΩ
10 kΩ
4
5
GND
6
ASKDTA
VS
General ground connection.
VS
Digital amplitude modulation can be
imparted to the Power Amplifier through this
pin.
+1.2 V
A logic high (ASKDTA > 1.5 V or open)
enables the Power Amplifier.
60 kΩ
6
+1.1 V
90 kΩ
50 pF
7
30 µA
FSKDTA
VS
A logic low (ASKDTA < 0.5 V)
disables the Power Amplifier.
Digital frequency modulation can be
imparted to the Xtal Oscillator by this pin.
The VCO-frequency varies in accordance to
the frequency of the reference oscillator.
+1.2 V
60 kΩ
7
+1.1 V
90 kΩ
30 µA
A logic high (FSKDTA > 1.5V or open)
sets the FSK switch to a high impedance
state.
A logic low (FSKDTA < 0.5 V)
closes the FSK switch
from FSKOUT (pin 11) to FSKGND (pin 12).
A capacitor can be switched to the reference
crystal network this way. The Xtal Oscillator
frequency will be shifted giving the designed
FSK frequency deviation.
Wireless Components
2-4
Specification, October 2002
TDK 5100
Functional Description
8
CLKOUT
Clock output to supply an external device.
An external pull-up resistor has to be added
in accordance to the driving requirements of
the external device.
A clock frequency of 3.39 MHz is selected
by a logic low at CLKDIV input (pin9).
A clock frequency of 847.5 kHz is selected
by a logic high at CLKDIV input (pin9).
VS
8
300 Ω
9
CLKDIV
VS
+1.2 V
VS
5 µA
60 kΩ
9
+0.8 V
60 kΩ
10
COSC
VS
VS
6 kΩ
10
This pin is used to select the desired clock
division rate for the CLKOUT signal.
A logic low (CLKDIV < 0.2 V) applied to this
pin selects the 3.39 MHz output signal at
CLKOUT (pin 8).
A logic high (CLKDIV open) applied to this
pin selects the 847.5 kHz output signal at
CLKOUT (pin 8).
This pin is connected to the reference oscillator circuit.
The reference oscillator is working as a negative impedance converter. It presents a
negative resistance in series to an inductance at the COSC pin.
100 µA
11
FSKOUT
This pin is connected to a switch to
FSKGND (pin 12).
VS
VS
The switch is closed when the signal at
FSKDTA (pin 7) is in a logic low state.
The switch is open when the signal at
FSKDTA (pin 7) is in a logic high state.
200 µA
1.5 kΩ
11
FSKOUT can switch an additional capacitor
to the reference crystal network to pull the
crystal frequency by an amount resulting in
the desired FSK frequency shift of the transmitter output frequency.
12
12
FSKGND
Wireless Components
Ground connection for FSK modulation output FSKOUT.
2-5
Specification, October 2002
TDK 5100
Functional Description
13
PAGND
Ground connection of the power amplifier.
The RF ground return path of the power
amplifier output PAOUT (pin 14) has to be
concentrated to this pin.
14
PAOUT
RF output pin of the transmitter.
14
A DC path to the positive supply VS has to
be supplied by the antenna matching network.
13
15
FSEL
This pin is used to select the desired transmitter frequency.
+1.2 V
VS
A logic low (FSEL < 0.5 V) applied to this pin
sets the transmitter to the 433 MHz frequency range.
30 kΩ
15
+1.1 V
90 kΩ
30 µA
16
CSEL
VS
+1.2 V
A logic high (FSEL open) applied to this pin
sets the transmitter to the 868 MHz frequency range.
This pin is used to select the desired reference frequency.
VS
5 µA
60 kΩ
16
A logic low (CSEL < 0.2 V) applied to this pin
sets the internal frequency divider to accept
a reference frequency of 6.78 MHz.
+0.8 V
60 kΩ
A logic high (CSEL open) applied to this pin
sets the internal frequency divider to accept
a reference frequency of 13.56 MHz.
1) Indicated voltages and currents apply for PLL Enable Mode and Transmit Mode.
In Power Down Mode, the values are zero or high-ohmic.
Wireless Components
2-6
Specification, October 2002
Wireless Components
7
2-7
Functional Block diagram
FSK
Ground
12
FSK
Switch
11
Crystal
6.78/13.56 MHz
Clock Output
Frequency
Select
0.85/3.39 MHz
ASK
Data
Input
Power
Down
Control
Positive
Supply
VS
1
3
6
OR
Low Power
Detect Output
2
Power
Supply
Low Voltage
Sensor 2.2V
On
10
9
XTAL
Osc
PFD
:128/64
Power
AMP
16
Crystal
Select
6.78/13.56 MHz
4
Loop
Filter
15
Frequency
Select
434/868 MHz
14
Power
Amplifier
Output
13
Power
Amplifier
Ground
5
Ground
TDK 5100
Functional Description
Block_diagram.wmf
Specification, October 2002
Clock
Output
:1/2
LF
:2/8
:4/16
8
VCO
2.3 Functional Block diagram
Figure 2-2
FSK
Data
Input
TDK 5100
Functional Description
2.4 Functional Blocks
2.4.1 PLL Synthesizer
The Phase Locked Loop synthesizer consists of a Voltage Controlled Oscillator
(VCO), an asynchronous divider chain, a phase detector, a charge pump and a
loop filter. It is fully implemented on chip. The tuning circuit of the VCO consisting of spiral inductors and varactor diodes is on chip, too. Therefore no additional external components are necessary. The nominal center frequency of the
VCO is 869 MHz. The oscillator signal is fed both, to the synthesizer divider
chain and to the power amplifier. The overall division ratio of the asynchronous
divider chain is 128 in case of a 6.78 MHz crystal or 64 in case of a 13.56 MHz
crystal and can be selected via CSEL (pin 16). The phase detector is a Type IV
PD with charge pump. The passive loop filter is realized on chip.
2.4.2 Crystal Oscillator
The crystal oscillator operates either at 6.78 MHz or at 13.56 MHz.
The reference frequency can be chosen by the signal at CSEL (pin 16).
Table 2-3
CSEL (pin 16)
1)
6.78 MHz
13.56 MHz
Low
Open2)
1) Low:
2) Open:
Crystal Frequency
Voltage at pin < 0.2 V
Pin open
For both quartz frequency options, 847.5 kHz or 3.39 MHz are available as output frequencies of the clock output CLKOUT (pin 8) to drive the clock input of a
micro controller.
The frequency at CLKOUT (pin 8) is controlled by the signal at CLKDIV (pin 9)
Table 2-4
CLKDIV (pin 9)
1)
3.39 MHz
847.5 kHz
Low
Open2)
1) Low:
2) Open:
Wireless Components
CLKOUT Frequency
Voltage at pin < 0.2 V
Pin open
2-8
Specification, October 2002
TDK 5100
Functional Description
To achieve FSK transmission, the oscillator frequency can be detuned by a
fixed amount by switching an external capacitor via FSKOUT (pin 11).
The condition of the switch is controlled by the signal at FSKDTA (pin 7).
Table 2-5
FSKDTA (pin7)
FSK Switch
1)
CLOSED
OPEN
Low
Open2), High3)
1) Low:
2) Open:
3) High:
Voltage at pin < 0.5 V
Pin open
Voltage at pin > 1.5 V
2.4.3 Power Amplifier
In case of operation in the 868-870 MHz band, the power amplifier is fed directly
from the voltage controlled oscillator. In case of operation in the 433-435 MHz
band, the VCO frequency is divided by 2. This is controlled by FSEL (pin 15) as
described in the table below.
Table 2-6
FSEL (pin 15)
Radiated Frequency Band
1)
433 MHz
868 MHz
Low
Open2)
1) Low:
2) Open:
Voltage at pin < 0.5 V
Pin open
The Power Amplifier can be switched on and off
by the signal at ASKDTA (pin 6).
Table 2-7
ASKDTA (pin 6)
1)
Low
Open2), High3)
1) Low:
2) Open:
3) High:
Power Amplifier
OFF
ON
Voltage at pin < 0.5 V
Pin open
Voltage at pin > 1.5 V
The Power Amplifier has an Open Collector output at PAOUT (pin 14) and
requires an external pull-up coil to provide bias. The coil is part of the tuning and
matching LC circuitry to get best performance with the external loop antenna.
To achieve the best power amplifier efficiency, the high frequency voltage swing
at PAOUT (pin 14) should be twice the supply voltage.
The power amplifier has its own ground pin PAGND (pin 13) in order to reduce
the amount of coupling to the other circuits.
Wireless Components
2-9
Specification, October 2002
TDK 5100
Functional Description
2.4.4 Low Power Detect
The supply voltage is sensed by a low power detector. When the supply voltage
drops below 2.15 V, the output LPD (pin 2) switches to the low-state. To minimize the external component count, an internal pull-up current of 40 µA gives
the output a high-state at supply voltages above 2.15 V.
The output LPD (pin 2) can either be connected to ASKDTA (pin 6) to switch off
the PA as soon as the supply voltage drops below 2.15 V or it can be used to
inform a micro-controller to stop the transmission after the current data packet.
2.4.5 Power Modes
The IC provides three power modes, the POWER DOWN MODE, the PLL
ENABLE MODE and the TRANSMIT MODE.
2.4.5.1 Power Down Mode
In the POWER DOWN MODE the complete chip is switched off.
The current consumption is typically 0.3 nA at 3 V 25°C.
This current doubles every 8°C. The values for higher temperatures are
typically 14 nA at 85°C and typically 600 nA at 125°C.
2.4.5.2 PLL Enable Mode
In the PLL ENABLE MODE the PLL is switched on but the power amplifier is
turned off to avoid undesired power radiation during the time the PLL needs to
settle. The turn on time of the PLL is determined mainly by the turn on time of
the crystal oscillator and is less than 1 msec when the specified crystal is used.
The current consumption is typically 3.5 mA.
2.4.5.3 Transmit Mode
In the TRANSMIT MODE the PLL is switched on and the power amplifier is
turned on too.
The current consumption of the IC is typically 7 mA when using a proper transforming network at PAOUT, see Figure 3-1.
2.4.5.4 Power mode control
The bias circuitry is powered up via a voltage V > 1.5 V at the pin PDWN (pin 1).
When the bias circuitry is powered up, the pins ASKDTA and FSKDTA are
pulled up internally.
Forcing the voltage at the pins low overrides the internally set state.
Alternatively, if the voltage at ASKDTA or FSKDTA is forced high externally, the
PDWN pin is pulled up internally via a current source. In this case, it is not necessary to connect the PDWN pin, it is recommended to leave it open.
Wireless Components
2 - 10
Specification, October 2002
TDK 5100
Functional Description
The principle schematic of the power mode control circuitry is shown in
Figure 3-5.
PDWN
ASKDTA
OR
FSKDTA
On
Bias
Source
Bias Voltage
120 kΩ
120 kΩ
FSKOUT
FSK
On
PLL
868
MHz
PA
PAOUT
IC
Power_Mode.wmf
Figure 2-5
Power mode control circuitry
Table 3-8 provides a listing of how to get into the different power modes
Table 2-8
PDWN
FSKDTA
ASKDTA
Low1)
Low, Open
Low, Open
Open2)
Low
Low
High3)
Low, Open, High
Low
Open
High
Low
High
Low, Open, High
Open, High
Open
High
Open, High
Open
Low, Open, High
High
1) Low:
2) Open:
3) High:
MODE
POWER DOWN
PLL ENABLE
TRANSMIT
Voltage at pin < 0.7 V (PDWN)
Voltage at pin < 0.5 V (FSKDTA, ASKDTA)
Pin open
Voltage at pin > 1.5 V
Other combinations of the control pins PDWN, FSKDTA and ASKDTA are not
recommended.
Wireless Components
2 - 11
Specification, October 2002
TDK 5100
Functional Description
2.4.6 Recommended timing diagrams for ASK- and FSK-Modulation
ASK Modulation using FSKDTA and ASKDTA, PDWN not connected
Modes:
Power Down
PLL Enable
Transmit
High
FSKDTA
Low
to
t
DATA
Open, High
ASKDTA
Low
to
t
min. 1 msec.
ASK_mod.wmf
Figure 2-6
ASK Modulation
FSK Modulation using FSKDTA and ASKDTA, PDWN not connected
Modes:
Power Down
PLL Enable
Transmit
DATA
High
FSKDTA
Low
to
t
to
t
High
ASKDTA
Low
min. 1 msec.
FSK_mod.wmf
Figure 2-7
Wireless Components
FSK Modulation
2 - 12
Specification, October 2002
TDK 5100
Functional Description
Alternative ASK Modulation, FSKDTA not connected.
Modes:
Power Down
PLL Enable
Transmit
High
PDWN
Low
to
t
DATA
Open, High
ASKDTA
Low
to
t
min. 1 msec.
Alt_ASK_mod.wmf
Figure 2-8
Alternative ASK Modulation
Alternative FSK Modulation
Modes:
Power Down
PLL Enable
Transmit
High
PDWN
Low
to
t
to
t
Open, High
ASKDTA
Low
DATA
Open, High
FSKDTA
Low
to
t
min. 1 msec.
Alt_FSK_mod.wmf
Figure 2-9
Wireless Components
Alternative FSK Modulation
2 - 13
Specification, October 2002
3
Applications
Contents of this Chapter
3.1
3.2
3.3
3.4
3.5
3.6
3.7
50 Ohm-Output Testboard Schematic . . . . . . . . . . . . . . . . . . . . . . . . 3-2
50 Ohm-Output Testboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Bill of material (50 Ohm-Output Testboard) . . . . . . . . . . . . . . . . . . . . 3-4
50 Ohm-Output Testboard: Measurement results . . . . . . . . . . . . . . . 3-5
Application Hints on the Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . 3-7
Design Hints on the Clock Output (CLKOUT). . . . . . . . . . . . . . . . . . . 3-9
Application Hints on the Power-Amplifier . . . . . . . . . . . . . . . . . . . . . 3-10
TDK 5100
Applications
3.1 50 Ohm-Output Testboard Schematic
X2SMA
C8
C2
C4
L2
L1
VCC
C7
433 (868)
MHz
C6
C3
10
9
8
11
7
12
13
14
15
6.78 (13.56)
MHz
16
Q1
0.85 (3.4)
MHz
VCC
6
5
4
3
2
VCC
1
TDK 5100
C1
T1
R3A
R3F
R4
R2
FSK
ASK
R1
C5
X1SMA
50ohm_test_v5.wmf
Figure 3-1
Wireless Components
50Ω-output testboard schematic
3-2
Specification, October 2002
TDK 5100
Applications
3.2 50 Ohm-Output Testboard Layout
Wireless Components
Figure 3-2
Top Side of TDK 5100-Testboard with 50 Ω-Output
Figure 3-3
Bottom Side of TDK 5100-Testboard with 50 Ω-Output
3-3
Specification, October 2002
TDK 5100
Applications
3.3 Bill of material (50 Ohm-Output Testboard)
Table 3-1 Bill of material
Part
Value
R1
4.7 kΩ
434 MHz
869 MHz
ASK
FSK
Specification
0805, ± 5%
12 kΩ
R2
R3A
15 kΩ
R3F
0805, ± 5%
0805, ± 5%
15 kΩ
0805, ± 5%
R4
open
0805, ± 5%
C1
47 nF
0805, X7R, ± 10%
C2
39 pF
47 pF
0805, COG, ± 5%
C3
3.9 pF
1.8 pF
0805, COG, ± 0.1 pF
C4
330 pF
100 pF
0805, COG, ± 5%
C5
1 nF
0805, X7R, ± 10%
C6
8.2 pF
0805, COG, ± 0.1 pF
C7
0Ω
Jumper
434MHz: 22 pF
868MHz: 47pF
0805, COG, ± 5%
0805, 0Ω Jumper
C8
15 pF
8.2 pF
0805, COG, ± 5%
L1
100 nH
33 nH
TOKO LL2012-J
L2
39 nH
15 nH
39 nH: TOKO LL2012-J
15 nH: TOKO LL1608-J
Q1
13.56875 MHz,
CL=20pF
IC1
TDK5100
T1
Push-button
replaced by a short
X1
SMA-S
SMA standing
X2
SMA-S
SMA standing
Wireless Components
Tokyo Denpa TSS-3B
13568.75 kHz
Spec.No. 10-50205
3-4
Specification, October 2002
TDK 5100
Applications
3.4 50 Ohm-Output Testboard: Measurement results
Note the specified operating range: 2.1 V to 4.0 V and −40°C to +125°C.
Pout over temperature TD K 5100 434 MH z
8,00
7,00
6,00
Pout [dBm]
5,00
4,0V
4,00
3,0V
3,00
2,1V
2,0V
2,00
1,9V
1,00
0,00
-1,00
-2,00
-50
0
50
100
150
T [°C]
pout_over_temp_434.wmf
Figure 3-4
Output power over temperature of the 50Ω-testboard with
TDK 5100 at 434 MHz
Is over temperatu re TD K 5100 434 MH z
8,00
7,50
Is [mA]
7,00
4,0V
3,0V
2,1V
6,50
2,0V
1,9V
6,00
5,50
5,00
-50
0
50
100
150
T [°C]
Is_over_temp_434.wmf
Figure 3-5
Wireless Components
Supply current over temperature of the 50Ω-testboard with
TDK 5100 at 434 MHz
3-5
Specification, October 2002
TDK 5100
Applications
Note the specified operating range: 2.1 V to 4.0 V and −40°C to +125°C.
Pout over temperature TD K 5100 868 MH z
6,00
5,00
4,00
Pout [dBm]
3,00
4,0V
2,00
3,0V
1,00
2,1V
0,00
2,0V
1,9V
-1,00
-2,00
-3,00
-4,00
-50
0
50
100
150
T [°C]
pout_over_temp_868.wmf
Figure 3-6
Output power over temperature of the 50Ω-testboard with
TDK 5100 at 868 MHz
Is over temperature TDK5100 868 MH z
8,00
7,50
Is [mA]
7,00
4,0V
3,0V
2,1V
6,50
2,0V
1,9V
6,00
5,50
5,00
-50
0
50
100
150
T [°C]
is_over_temp_868.wmf
Figure 3-7
Wireless Components
Supply current over temperature of the 50Ω-testboard with
TDK 5100 at 868 MHz
3-6
Specification, October 2002
TDK 5100
Applications
3.5 Application Hints on the Crystal Oscillator
1. Application Hints on the crystal oscillator
The crystal oscillator achieves a turn on time less than 1 msec when the
specified crystal is used. To achieve this, a NIC oscillator type is implemented
in the TDK 5100. The input impedance of this oscillator is a negative resistance
in series to an inductance. Therefore the load capacitance of the crystal CL
(specified by the crystal supplier) is transformed to the capacitance Cv.
-R
L
f, CL Cv
IC
Cv =
1
1
+ω2L
CL
Formula 1)
CL:
crystal load capacitance for nominal frequency
ω:
angular frequency
L:
inductance of the crystal oscillator
Example for the ASK-Mode:
Referring to the application circuit, in ASK-Mode the capacitance C7 is replaced
by a short to ground. Assume a crystal frequency of 13.56 MHz and a crystal
load capacitance of CL = 20 pF. The inductance L at 13.5 MHz is about 4.6 µH.
Therefore C6 is calculated to 12 pF.
Cv =
Wireless Components
3-7
1
1
+ω 2L
CL
= C6
Specification, October 2002
TDK 5100
Applications
Example for the FSK-Mode:
FSK modulation is achieved by switching the load capacitance of the crystal as
shown below.
FSKDTA
FSKOUT
Csw
-R
L
Cv2
f, CL Cv1
COSC
IC
The frequency deviation of the crystal oscillator is multiplied with the divider
factor N of the Phase Locked Loop to the output of the power amplifier. In case
of small frequency deviations (up to +/- 1000 ppm), the two desired load
capacitances can be calculated with the formula below.
2(C 0 + CL )
∆f
)
(1 +
N * f1
C1
2(C 0 + CL )
∆f
)
1±
(1 +
N * f1
C1
CL # C 0
CL ± =
C L:
C 0:
f:
ω:
N:
df:
crystal load capacitance for nominal frequency
shunt capacitance of the crystal
frequency
ω = 2πf: angular frequency
division ratio of the PLL
peak frequency deviation
Because of the inductive part of the TDK 5100, these values must be corrected
by Formula 1). The value of Cv± can be calculated.
Wireless Components
3-8
Specification, October 2002
TDK 5100
Applications
If the FSK switch is closed, Cv_ is equal to Cv1 (C6 in the application diagram).
If the FSK switch is open, Cv2 (C7 in the application diagram) can be calculated.
Cv 2 = C 7 =
Csw ∗ Cv1 − (Cv + ) ∗ (Cv1 + Csw)
(Cv + ) − Cv1
Csw:
parallel capacitance of the FSK switch (3 pF incl. layout parasitics)
Remark:
These calculations are only approximations. The necessary values
depend on the layout also and must be adapted for the specific
application board.
3.6 Design Hints on the Clock Output (CLKOUT)
The CLKOUT pin is an open collector output. An external pull up resistor (RL)
should be connected between this pin and the positive supply voltage. The
value of RL is depending on the clock frequency and the load capacitance CLD
(PCB board plus input capacitance of the microcontroller). RL can be calculated
to:
RL =
1
fCLKOUT * 8 * CLD
Table 3-2
fCLKOUT=
847 kHz
CL[pF]
fCLKOUT=
3.39 MHz
RL[kOhm]
CL[pF]
RL[kOhm]
5
27
5
6.8
10
12
10
3.3
20
6.8
20
1.8
Remark:
To achieve a low current consumption and a low
spurious radiation, the largest possible RL should be chosen.
Even harmonics of the signal at CLKOUT can interact with the crystal oscillator
input COSC preventing the start-up of oscillation. Care must be taken in layout
by sufficient separation of the signal lines to ensure sufficiently small coupling.
Wireless Components
3-9
Specification, October 2002
TDK 5100
Applications
3.7 Application Hints on the Power-Amplifier
The power amplifier operates in a high efficient class C mode. This mode is
characterized by a pulsed operation of the power amplifier transistor at a current
flow angle of θ<<π. A frequency selective network at the amplifier output
passes the fundamental frequency component of the pulse spectrum of the
collector current to the load. The load and its resonance transformation to the
collector of the power amplifier can be generalized by the equivalent circuit of
Figure 3-8. The tank circuit L//C//RL in parallel to the output impedance of the
transistor should be in resonance at the operating frequency of the transmitter.
VS
L
C
RL
Equivalent_power_wmf.
Figure 3-8
Equivalent power amplifier tank circuit
The optimum load at the collector of the power amplifier for “critical” operation
under idealized conditions at resonance is:
R LC =
V S2
2 * PO
The theoretical value of RLC for an RF output power of Po= 5 dBm (3.16 mW) is:
R LC
32
=
= 1423 Ω
2 * 0 .00316
“Critical” operation is characterized by the RF peak voltage swing at the
collector of the PA transistor to just reach the supply voltage VS.
The high degree of efficiency under “critical” operating conditions can be
explained by the low power losses at the transistor. During the conducting
phase of the transistor, its collector voltage is very small. This way the power
loss of the transistor, equal to iC*uCE , is minimized. This is particularly true for
small current flow angles of θ<<π.
In practice the RF-saturation voltage of the PA transistor and other parasitics
reduce the “critical” RLC.
Wireless Components
3 - 10
Specification, October 2002
TDK 5100
Applications
The output power Po is reduced by operating in an “overcritical” mode
characterised by RL > RLC.
The power efficiency (and the bandwidth) increase when operating at a slightly
higher RL, as shown in Figure 3-9.
The collector efficiency E is defined as
E=
PO
VS I C
The diagram of Figure 3-9 was measured directly at the PA-output at VS = 3 V.
Losses in the matching circuitry decrease the output power by about 1.5 dB. As
can be seen from the diagram, 700 Ω is the optimum impedance for operation
at 3 V. For an approximation of ROPT and POUT at other supply voltages those
two formulas can be used:
ROPT ~ VS
and
POUT ~ ROPT
0 *E
o [m W ]
7
6
5
4
3
10*E
2
Po
1
0
0
1000
2000
3000
R L [O h m ]
Power_output.wmf
Figure 3-9
Output power Po (mW) and collector efficiency E vs. load resistor RL.
The DC collector current Ic of the power amplifier and the RF output power Po
vary with the load resistor RL. This is typical for overcritical operation of class C
amplifiers. The collector current will show a characteristic dip at the resonance
frequency for this type of “overcritical” operation. The depth of this dip will
increase with higher values of RL.
Wireless Components
3 - 11
Specification, October 2002
TDK 5100
Applications
As Figure 3-10 shows, detuning beyond the bandwidth of the matching circuit
results in an increase of the collector current of the power amplifier and in some
loss of output power. This diagram shows the data for the circuit of the test
board at the frequency of 434 MHz. The behaviour at 868 MHz is similar. The
effective load resistance of this circuit is RL = 700 Ω, which is the optimum
impedance for operation at 3 V. This will lead to a dip of the collector current of
approx. 40%.
Ic [mA ]
Po [d B m]
6
5
4
3
2
1
0
420
430
440
450
f [M H z ]
pout_vs_frequ.wmf
Figure 3-10
Output power and collector current vs. frequency
C3, L2-C2 and C8 are the main matching components which are used to
transform the 50 Ω load at the SMA-RF-connector to a higher impedance at the
PA-output (700 Ω @ 3 V). L1 can be used for some finetuning of the resonant
frequency but should not become too small in order to keep its losses low.
The transformed impedance of 700+j0 Ω at the PA-output-pin can be verified
with a network analyzer using the following measurement procedure:
1. Calibrate your network analyzer.
2. Connect some short, low-loss 50 Ω cable to your network analyzer with an
open end on one side. Semirigid cable works best.
3. Use the „Port Extension“ feature of your network analyzer to shift the reference plane of your network analyzer to the open end of the cable.
4. Connect the center-conductor of the cable to the solder pad of the pin „PA“
of the IC. The outer conductor has to be grounded. Very short connections
have to be used. Do not remove the IC or any part of the matching-components!
5. Screw a 50 Ω dummy-load on the RF-I/O-SMA-connector
6. Be sure that your network analyzer is AC-coupled and turn on the power
supply of the IC. The TDK5100 must not be in Transmit-Mode.
7. Measure the S-parameter S11
Wireless Components
3 - 12
Specification, October 2002
TDK 5100
Applications
LoadImpedance50ohmBoard.wmf
Figure 3-11
S-parameters of the load at the PA-output
Above you can see the measurement of the evalboard with a span of 100 MHz.
The evalboard has been optimized for 3 V. The load is about 700+j0 Ω at
the transmit frequency.
A tuning-free realization requires a careful design of the components within the
matching network. A simple linear CAE-tool will help to see the influence of
tolerances of matching components.
Suppression of spurious harmonics may require some additional filtering within
the antenna matching circuit. The total spectrum of a typical 50 Ω-Output
testboard can be summarized as:
Table 3-3
Frequency
Wireless Components
Output Power
434 MHz Testboard
Output Power
868 MHz Testboard
Fundamental
+5 dBm
+2 dBm
Fund − 13.56 MHz
-81 dBc
-78 dBc
Fund + 13.56 MHz
-88 dBc
-75 dBc
2nd harmonic
-40 dBc
-43 dBc
3rd harmonic
-52 dBc
-52 dBc
3 - 13
Specification, October 2002
4
Reference
Contents of this Chapter
4.1
4.2
4.3
4.3.1
4.3.2
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
AC/DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
AC/DC Characteristics at 3V, 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
AC/DC Characteristics at 2.1 V ... 4.0 V, -40°C ... +125°C. . . . . . . . . 4-6
TDK 5100
Reference
4.1 Absolute Maximum Ratings
The AC / DC characteristic limits are not guaranteed. The maximum ratings
must not be exceeded under any circumstances, not even momentarily and
individually, as permanent damage to the IC may result.
Table 4-1
Symbol
Parameter
Limit Values
Min
Max
Unit
Junction Temperature
TJ
−40
+150
°C
Storage Temperature
Ts
−40
+125
°C
230
K/W
Thermal Resistance
RthJA
Remarks
VS
−0.3
+4.0
V
Voltage at any pin
excluding pin 14
Vpins
-0.3
VS + 0.3
V
Voltage at pin 14
Vpin14
-0.3
2 * VS
V
Current into pin 11
Ipin11
-10
10
mA
ESD integrity, all pins
VESD
-1
+1
kV
JEDEC Standard
JESD22-A114-B
ESD integrity, all pins
excluding pin 14
VESD
-2
+2
kV
JEDEC Standard
JESD22-A114-B
Supply voltage
No ESD-Diode to
VS
Ambient Temperature under bias: TA = −40°C to +125°C
Note: All voltages referred to ground (pins) unless stated otherwise.
Pins 5, 12 and 13 are grounded.
4.2 Operating Range
Within the operational range the IC operates as described in the circuit
description.
Table 4-2
Parameter
Symbol
Limit Values
Min
Max
Unit
Supply voltage
VS
2.1
4.0
V
Ambient temperature
TA
-40
125
°C
Wireless Components
4-2
Test Conditions
Specification, October 2002
TDK 5100
Reference
4.3 AC/DC Characteristics
4.3.1
AC/DC Characteristics at 3V, 25°C
Table 4-3 Supply Voltage VS = 3 V, Ambient temperature Tamb = 25°C
Parameter
Symbol
Limit Values
Min
Unit
Typ
Max
Test Conditions
Current consumption
Power Down mode
IS PDWN
0.3
100
nA
PLL Enable mode
IS PLL_EN
3.5
4.2
mA
7
8.8
mA
7
9
mA
Transmit mode 434 MHz
Transmit mode 868 MHz
IS TRANSM
V (Pins 1, 6 and 7)
< 0.2 V
Load tank see
Figure 4-1 and 4-2
Power Down Mode Control (Pin 1)
Power Down mode
V PDWN
0
0.7
V
VASKDTA < 0.2 V
VFSKDTA < 0.2 V
PLL Enable mode
V PDWN
1.5
VS
V
VASKDTA < 0.5 V
Transmit mode
V PDWN
1.5
VS
V
VASKDTA > 1.5 V
Input bias current PDWN
IPDWN
30
µA
VPDWN = VS
Low Power Detect Output (Pin 2)
Internal pull up current
I LPD1
30
µA
VS = 2.3 V ... VS
Input current low voltage
I LPD2
1
mA
VS = 1.9 V ... 2.1 V
V
fVCO = 867.84 MHz
Loop Filter (Pin 4)
VCO tuning voltage
VLF
Output frequency range
868 MHz-band
fOUT, 868
854
869
884
MHz
VFSEL = VS
fOUT = fVCO
Output frequency range
433 MHz-band
fOUT, 433
427
434.5
442
MHz
VFSEL = 0 V
fOUT = fVCO / 2
VS - 1.5
VS - 0.7
ASK Modulation Data Input (Pin 6)
ASK Transmit disabled
VASKDTA
0
0.5
V
ASK Transmit enabled
VASKDTA
1.5
VS
V
Input bias current ASKDTA
IASKDTA
30
µA
VASKDTA = VS
Input bias current ASKDTA
IASKDTA
µA
VASKDTA = 0 V
ASK data rate
fASKDTA
Wireless Components
-20
20
4-3
kHz
Specification, October 2002
TDK 5100
Reference
Table 4-3 Supply Voltage VS = 3 V, Ambient temperature Tamb = 25°C
Parameter
Symbol
Limit Values
Min
Typ
Unit
Test Conditions
Max
FSK Modulation Data Input (Pin 7)
FSK Switch on
VFSKDTA
0
0.5
V
FSK Switch off
VFSKDTA
1.5
VS
V
Input bias current FSKDTA
IFSKDTA
30
µA
VFSKDTA = VS
Input bias current FSKDTA
IFSKDTA
µA
VFSKDTA = 0 V
FSK data rate
fFSKDTA
20
kHz
Output current (High)
ICLKOUT
5
µA
VCLKOUT = VS
Saturation Voltage (Low)1)
VSATL
0.56
V
ICLKOUT = 1 mA
0.2
V
-20
Clock Driver Output (Pin 8)
Clock Divider Control (Pin 9)
Setting Clock Driver output
frequency fCLKOUT=3.39 MHz
VCLKDIV
Setting Clock Driver output
frequency fCLKOUT=847.5kHz
VCLKDIV
Input bias current CLKDIV
ICLKDIV
Input bias current CLKDIV
ICLKDIV
0
30
-20
V
pin open
µA
VCLKDIV = VS
µA
VCLKDIV = 0 V
Crystal Oscillator Input (Pin 10)
Load capacitance
CCOSCmax
Serial Resistance of the crystal
3.25
Input inductance of the
COSC pin
4.25
Serial Resistance of the crystal
Input inductance of the
COSC pin
3.6
4.6
5
pF
100
Ω
f = 6.78 MHz
5.25
µH
f = 6.78 MHz
100
Ω
f = 13.56 MHz
5.6
µH
f = 13.56 MHz
FSK Switch Output (Pin 11)
On resistance
RFSKOUT
250
Ω
VFSKDTA = 0 V
On capacitance
CFSKOUT
6
pF
VFSKDTA = 0 V
Off resistance
RFSKOUT
kΩ
VFSKDTA = VS
Off capacitance
CFSKOUT
pF
VFSKDTA = VS
Wireless Components
10
1.5
4-4
Specification, October 2002
TDK 5100
Reference
Table 4-3 Supply Voltage VS = 3 V, Ambient temperature Tamb = 25°C
Parameter
Symbol
Limit Values
Unit
Test Conditions
Min
Typ
Max
POUT433
4
5
6
dBm
fOUT = 433 MHz
VFSEL = 0 V
POUT868
0
2
4
dBm
fOUT = 868 MHz
VFSEL = VS
Power Amplifier Output (Pin 14)
Output Power2)
transformed to 50 Ohm
Frequency Range Selection (Pin 15)
Transmit frequency 433 MHz
VFSEL
Transmit frequency 868 MHz
VFSEL
Input bias current FSEL
IFSEL
Input bias current FSEL
IFSEL
0
0.5
30
-20
V
V
pin open
µA
VFSEL = VS
µA
VFSEL = 0 V
Crystal Frequency Selection (Pin 16)
Crystal frequency 6.78 MHz
VCSEL
Crystal frequency 13.56 MHz
VCSEL
Input bias current CSEL
ICSEL
Input bias current CSEL
ICSEL
1)
2)
0
0.2
50
-25
V
V
pin open
µA
VCSEL = VS
µA
VCSEL = 0 V
Derating linearly to a saturation voltage of max. 140 mV at ICLKOUT = 0 mA
Power amplifier in overcritical C-operation
Matching circuitry as used in the 50 Ohm-Output Testboard at the specified frequency.
Tolerances of the passive elements not taken into account.
Wireless Components
4-5
Specification, October 2002
TDK 5100
Reference
4.3.2
AC/DC Characteristics at 2.1 V ... 4.0 V, -40°C ... +125°C
Table 4-4 Supply Voltage VS = 2.1 V ... 4.0 V, Ambient temperature Tamb = -40°C ... +125°C
Parameter
Symbol
Limit Values
Min
Typ
Unit
Test Conditions
Max
Current consumption
Power Down mode
IS PDWN
PLL Enable mode
IS PLL_EN
Transmit mode
IS TRANSM
4
µA
3.5
4.6
mA
7
9.5
mA
Load tank see
Figure 4-1 and 4-2
V (Pins 1, 6 and 7)
< 0.2 V
Power Down Mode Control (Pin 1)
Power Down mode
V PDWN
0
0.5
V
VASKDTA < 0.2 V
VFSKDTA < 0.2 V
PLL Enable mode
V PDWN
1.5
VS
V
VASKDTA < 0.5 V
Transmit mode
V PDWN
1.5
VS
V
VASKDTA > 1.5 V
Input bias current PDWN
IPDWN
38
µA
VPDWN = VS
Low Power Detect Output (Pin 2)
Internal pull up current
I LPD1
30
µA
VS = 2.3 V ... VS
Input current low voltage
I LPD2
0.5
mA
VS = 1.9 V ... 2.1 V
V
fVCO = 867.84 MHz
Loop Filter (Pin 4)
VCO tuning voltage
VLF
VS - 1.8
VS - 0.5
Output frequency range 1)
868 MHz-band
fOUT, 868
864
869
874
MHz
VFSEL = VS
fOUT = fVCO
Output frequency range
433 MHz-band
fOUT, 433
432
434.5
437
MHz
VFSEL = 0 V
fOUT = fVCO / 2
ASK Modulation Data Input (Pin 6)
ASK Transmit disabled
VASKDTA
0
0.5
V
ASK Transmit enabled
VASKDTA
1.5
VS
V
Input bias current ASKDTA
IASKDTA
33
µA
VASKDTA = VS
Input bias current ASKDTA
IASKDTA
µA
VASKDTA = 0 V
ASK data rate
fASKDTA
Wireless Components
-20
20
4-6
kHz
Specification, October 2002
TDK 5100
Reference
Table 4-4 Supply Voltage VS = 2.1 V ... 4.0 V, Ambient temperature Tamb = -40°C ... +125°C
Parameter
Symbol
Limit Values
Min
Typ
Unit
Test Conditions
Max
FSK Modulation Data Input (Pin 7)
FSK Switch on
VFSKDTA
0
0.5
V
FSK Switch off
VFSKDTA
1.5
VS
V
Input bias current FSKDTA
IFSKDTA
35
µA
VFSKDTA = VS
Input bias current FSKDTA
IFSKDTA
µA
VFSKDTA = 0 V
FSK data rate
fFSKDTA
20
kHz
Output current (High)
ICLKOUT
5
µA
VCLKOUT = VS
Saturation Voltage (Low)2)
VSATL
0.5
V
ICLKOUT = 0.6 mA
0.2
V
-20
Clock Driver Output (Pin 8)
Clock Divider Control (Pin 9)
Setting Clock Driver output
frequency fCLKOUT=3.39 MHz
VCLKDIV
Setting Clock Driver output
frequency fCLKOUT=847.5kHz
VCLKDIV
Input bias current CLKDIV
ICLKDIV
Input bias current CLKDIV
ICLKDIV
0
30
-20
V
pin open
µA
VCLKDIV = VS
µA
VCLKDIV = 0 V
Crystal Oscillator Input (Pin 10)
Load capacitance
CCOSCmax
Serial Resistance of the crystal
2.9
Input inductance of the
COSC pin
4.25
Serial Resistance of the crystal
Input inductance of the
COSC pin
3.2
4.6
5
pF
100
Ω
f = 6.78 MHz
6
µH
f = 6.78 MHz
100
Ω
f = 13.56 MHz
6.3
µH
f = 13.56 MHz
FSK Switch Output (Pin 11)
On resistance
RFSKOUT
280
Ω
VFSKDTA = 0 V
On capacitance
CFSKOUT
6
pF
VFSKDTA = 0 V
Off resistance
RFSKOUT
kΩ
VFSKDTA = VS
Off capacitance
CFSKOUT
pF
VFSKDTA = VS
Wireless Components
10
1.5
4-7
Specification, October 2002
TDK 5100
Reference
Table 4-4 Supply Voltage VS = 2.1 V ... 4.0 V, Ambient temperature Tamb = -40°C ... +125°C
Parameter
Symbol
Limit Values
Min
Typ
Unit
Test Conditions
dBm
VS = 2.1 V
dBm
VS = 3.0 V
Max
Power Amplifier Output (Pin 14)
Output Power 3) at 434 MHz
transformed to 50 Ohm.
POUT, 434
-0.5
2.4
POUT, 434
0.5
5
VFSEL = 0 V
POUT, 434
1.5
6.6
dBm
VS = 4.0 V
Output Power 4) at 868 MHz
transformed to 50 Ohm.
POUT, 868
-4
0
dBm
VS = 2.1 V
POUT, 868
-3.6
2
dBm
VS = 3.0 V
VFSEL = VS
POUT, 868
-3
3.2
dBm
VS = 4.0 V
7
5
Frequency Range Selection (Pin 15)
Transmit frequency 434 MHz
VFSEL
Transmit frequency 868 MHz
VFSEL
Input bias current FSEL
IFSEL
Input bias current FSEL
IFSEL
0
0.5
35
-20
V
V
pin open
µA
VFSEL = VS
µA
VFSEL = 0 V
Crystal Frequency Selection (Pin 16)
Crystal frequency 6.78 MHz
VCSEL
Crystal frequency 13.56 MHz
VCSEL
Input bias current CSEL
ICSEL
Input bias current CSEL
ICSEL
0
0.2
55
-25
V
V
pin open
µA
VCSEL = VS
µA
VCSEL = 0 V
1) The output-frequency range can be increased by limiting the temperature and supply voltage
range.
Minimum fVCO − 1 MHz => Minimum Tamb + 5°C
Maximum fVCO + 1 MHz => Maximum Tamb − 5°C
Maximum fVCO + 1 MHz => Minimum VS + 25 mV, max. + 40 MHz.
2) Derating linearly to a saturation voltage of max. 140 mV at ICLKOUT = 0 mA
3) Matching circuitry as used in the 50 Ohm-Output Testboard for 434 MHz operation.
Tolerances of the passive elements not taken into account.
Range @ 2.1 V, +25°C: 2.4 dBm +/- 0.7 dBm
Typ. temperature dependency at 2.1 V: +0.4 dBm@-40°C and -1.4 dBm@+125°C, reference +25°C
Range @ 3.0 V, +25°C: 5.0 dBm +/- 1.0 dBm
Typ. temperature dependency at 3.0 V: +0.5 dBm@-40°C and -1.9 dBm@+125°C, reference +25°C
Range @ 4.0 V, +25°C: 6.6 dBm +/- 2.0 dBm
Typ. temperature dependency at 4.0 V: +0.6 dBm@-40°C and -3.1 dBm@+125°C, reference +25°C
4) Matching circuitry as used in the 50 Ohm-Output Testboard for 868 MHz operation.
Tolerances of the passive elements not taken into account.
Range @ 2.1 V, +25°C: 0.0 dBm +/- 1.0 dBm
Typ. temperature dependency at 2.1 V: +0.6 dBm@-40°C and -2.5 dBm@+125°C, reference +25°C
Range @ 3.0 V, +25°C: 2.0 dBm +/- 2.0 dBm
Typ. temperature dependency at 3.0 V: +0.9 dBm@-40°C and -3.6 dBm@+125°C, reference +25°C
Range @ 4.0 V, +25°C: 3.2 dBm +/- 2.7 dBm
Typ. temperature dependency at 4.0 V: +1.3 dBm@-40°C and -4.0 dBm@+125°C, reference +25°C
A smaller load impedance reduces the supply-voltage dependency.
A higher load impedance reduces the temperature dependency.
Wireless Components
4-8
Specification, October 2002