PC3SH13YFZAX

PC3SH13YFZAX
PC3SH13YFZAX
VDRM : 600V, Reinforced insulation type
Non-zero cross type
DIP 4 pin
Phototriac Coupler for triggering
■Description
■Agency approvals/Compliance
PC3SH13YFZAX reinforced insulation type
Phototriac Coupler include an infrared emitting diode
(IRED) optically coupled to an output Phototriac.
These devices feature full wave control and are ideal
isolated drivers for medium to high current Triacs.
DIP package provides 5.0kV isolation from input to
output with superior commutative noise immunity.
1. Recognized by UL1577 (Double protection
isolation), file No. E64380 (as model No. 3SH13)
2. Approved by CSA, file No. CA95323
(as model No. 3SH13)
3. Approved by BSI : file No.6690/7421
(BS EN60065/BS EN60950-1),
(as model No. 3SH13)
4. Approved by SEMKO, EN60065/EN60335-1/
EN60950-1 (as model No. 3SH13)
5. Approved by DEMKO, EN60065/EN60335-1/
EN60950-1 (as model No. 3SH13)
6. Approved by FIMKO, EN60065/EN60335-1/
EN60950-1 (as model No. 3SH13)
7. Approved by VDE
(DIN EN 60747-5-5), file No. 40008087
(as model No. 3SH13)
8. Package resin : UL flammability grade (94V-0)
■Features
1. High repetitive peak off-state voltage
(VDRM : 600V)
2. Non-zero crossing functionality
3. 4 pin DIP package
4. Reinforced insulation type
(MIN. 0.4mm internal separation)
5. Double transfer mold construction
(Ideal for Flow Soldering)
6. High isolation voltage between input and
output
(Viso(rms) : 5.0kV)
7. RoHS directive compliant
Notice
■Applications
1. Triggering for Triacs used to switch on and off
devices which require AC loads.
For example heaters, fans, motors, solenoids, and
valves.
2. Triggering for Triacs used for implementing phase
control in applications such as lighting control and
temperature control (HVAC).
3. AC line control in power supply applications.
The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: OP14020EN
1
PC3SH13YFZAX
■Outline
Rank mark *3
Factory identification mark *2
Pin-Number and internal
connection diagram
３ＳＨ１３
1.0 ±0.1
４
4.58 ±0.30
2.54 ±0.25
Date code *1
0.6 ±0.2
1.2 ±0.3
Anode mark
1
4
2
3
6.5 ±0.3
VDE identification mark *4
1. Anode
2. Cathode
3. Anode/Cathode
4. Cathode/Anode
4.58 ±0.30
2.7MIN.
3.5 ±0.5
7.62 ±0.30
Epoxy resin
0.26 ±0.10
0.5 ±0.1
10.16 ±0.50
*1) 2-digit number shall be marked according to OLD DIN standard.
*2) Factory identification mark applies to the below.
or
:
SUN-S Electronic Technology (KUNSHAN) Co., Ltd (China)
*3) Rank mark : "A"
*4) VDE identification mark shall be marked "4".
*5) Pin material : Copper Alloy
Pin finish : SnCu plating (Cu : TYP. 2%)
Product mass
:
Approx.0.23g
Unit : 1/1mm
Name
3SH13 Outline Dimensions
(Business dealing name : PC3SH13YFZAX)
Sheet No.: OP14020EN
2
PC3SH13YFZAX
■Absolute maximum ratings
Symbol
Rating
Ta=25°C
Unit
IF
50
mA
VR
6
V
IT(rms)
0.1
A
Isurge
1.2
A
VDRM
600
V
Viso(rms)
5
kV
Operating temperature
Topr
-30 to +100
°C
Storage temperature
Tstg
-55 to +125
°C
Parameter
Input
Forward current
*1
Reverse voltage
RMS on-state current
Output
*1
Peak one cycle surge current
*2
Repetitive peak off-state voltage
Isolation voltage
*3
Soldering temperature *4
Tsol
270
°C
*1 The derating factors of absolute maximum rating due to ambient temperature are shown in Fig.3, 4.
*2 50Hz sine wave
*3 AC for 1min, 40 to 60%RH, f=60Hz
*4 For 10s
■Electrical characteristics
Input
Output
Ta=25°C
Conditions
IF=20mA
VR=3V
Parameter
Forward voltage
Reverse current
Symbol
VF
IR
MIN.
-
TYP.
1.2
-
MAX.
1.4
10-5
Unit
V
A
Repetitive peak
off-state current
IDRM
-
-
10-6
A
On-state voltage
Holding current
VT
IH
0.1
-
3.0
3.5
V
mA
IT=0.1A
VD=6V
dv/dt
500
-
-
V/μs
VD=1/√2・VDRM
IFT
RISO
5×1010
1011
10
-
mA
Ω
VD=6V, RL=100Ω
DC500V 40 to 60%RH
tON
-
-
100
μs
VD=6V, RL=100Ω,
IF=20mA
Critical rate of rise
of off-state voltage
Minimum trigger current
Transfer Isolation resistance
characteristics Turn on time
VD=VDRM
Sheet No.: OP14020EN
3
PC3SH13YFZAX
Fig.3 Forward current vs. ambient temperature
70
Forward current IF (mA)
60
50
40
30
20
10
0
-30 -20 -10 0
10 20 30 40 50 60 70 80 90 100
Ambient temperature Ta (°C)
Fig.4 RMS on-state current vs. ambient temperature
(mA)
150
RMS on-state current IT(rms)
175
125
100
75
50
25
0
-30 -20 -10 0
10 20
30 40 50 60 70 80 90 100
Ambient temperature Ta (°C)
Sheet No.: OP14020EN
4
PC3SH13YFZAX
■Supplement
● Business dealing name
The business dealing name used for this product when ordered or delivered shall be PC3SH13YFZAX.
● Package specification
Refer to the attached sheet, page 8 to 9.
● Isolation voltage shall be measured in the following method.
(1) Short between pins 1 to 2 on the primary side and between pins 3 to 4 on the secondary side.
(2) The dielectric withstanding tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
● The relevant models are the models Approved by VDE according to DIN EN 60747-5-5.
Approved Model No. : 3SH13
VDE approved No. : 40008087 (According to the specification DIN EN 60747-5-5 )
・Operating isolation voltage
VIORM (Peak)
: 1140V
・Transient voltage
: 9000V
・Pollution
: 2
・Clearances distance (Between input and output)
: 8.0 mm (MIN.)
・Creepage distance (Between input and output)
: 8.0 mm (MIN.)
・Isolation thickness between input and output
: 0.4 mm (MIN.)
・Tracking-proof
: CTI 175
・Safety limit values
Current (Isi)
: 200mA (Diode side)
Power (Psi)
: 400mW (Phototransistor side)
Temperature (Tsi)
: 150°C
In order to keep safety electric isolation of photocoupler, please set the protective circuit to keep within safety
limit values when the actual application equipment troubled.
・Indication of VDE approval " DVE
" is printed on minimum unit package.
Isolation specification according to EN 60747-5-5.
Parameter
Symbol
Class of environmental test
Pollution
Maximum operating isolation voltage
VIORM(PEAK)
Conditions
-
Rating
40/100/21
2
1140
Unit
V
tm=10s, qc＜5pC
1830
V
tst1=1s, qc＜5pC
tini=60 s
2140
V
9000
V
Partial discharge test voltage
(Between input and output)
Diagram 1
Diagram 2
Maximum over-voltage
Safety maximum ratings
Vm(PEAK)
Vini,a(PEAK)
1)
Case temperature
Tsi
IF=0, Pc=0
150
°C
2)
Input current
Isi
Pc=0
200
mA
400
mW
3) Electric power
(Output or Total power dissipation)
Isolation resistance
(Test voltage between input and output ;
DC 500V)
Psi
-
RISO
Tamb=Tsi
MIN. 109
Tamb=100°C
Tamb= 25°C
MIN. 1011
MIN. 1012
Remark
Refer to
the Diagram 1, 2
(Page 8/11)
Refer to
Fig.1, 2
(Page 8/11)
Ω
Precautions in performing isolation test
(1) Partial discharge test methods shall be the ones according to the specifications of EN 60747-5-5
(2) Please don't carry out isolation test (Viso) over Vini,a.
This product deteriorates isolation characteristics by partial discharge due to applying high voltage (ex. Vini,a).
And there is possibility that partial discharge occurs in operating isolation voltage. (VIORM).
Sheet No.: OP14020EN
5
PC3SH13YFZAX
● This Model is approved by UL, CSA.
Approved Model No. : 3SH13
UL file No. : E64380
CSA file No. : CA95323
CSA approved mark “
” shall be indicated on minimum unit package.
● This product is approved by BSI.
Approved Model No. : 3SH13
BSI Certificate No. : file No.6690/7421(BS EN60065/BS EN60950-1)
● This product is approved by SEMKO, DEMKO and FIMKO.
● This product is not designed against irradiation.
This product incorporates non-coherent light emitting diode.
This product is assembled with electrical input and output.
● ODS materials
(1) This product shall not contain the following materials.
(2) The following materials shall not be used in the production process for this product.
Materials for ODS : CFCS, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
● Specific brominated flame retardants (PBB and PBDE) are not used in this device at all.
● Compliance with each regulation
(1) The RoHS directive(2002/95/EC)
This product complies with the RoHS directive(2002/95/EC) .
Object substances: mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and
polybrominated diphenyl ethers (PBDE)
(2) Content of six substances specified in Management Methods for Control of Pollution Caused
by Electronic Information Products Regulation (Chinese : 电子信息产品污染控制管理办法).
Toxic and hazardous substances
Hexavalent
Polybrominated Polybrominated
Category
Lead
Mercury
Cadmium
chromium
biphenyls
diphenyl ethers
(Pb)
(Hg)
(Cd)
(Cr6+)
(PBB)
(PBDE)
Phototriac coupler
✓
✓
✓
✓
✓
✓
✓: indicates that the content of the toxic and hazardous substance in all the homogeneous materials of the
part is below the concentration limit requirement as described in SJ/T 11363-2006 standard.
Sheet No.: OP14020EN
6
PC3SH13YFZAX
■Notes
● Circuit design
(1) The LED used in the Phototriac coupler generally decreases the light emission power by operation.
In case of long operation time, please decide IF value so that IF is more than 2 times of the Maximum value
of the Minimum triggering current at circuit design with considering the decreases of the light emission power
of the LED. (50% / 5years)
(2) Input current (IF) at off-state shall be set 0.1mA or less.
(3) In case that pulse drive is carried out, the pulse width of input signal should be 1ms or more
● Usage
Triggering medium power triac and high power triac.
(This model shall be used under the conditions on which power triac turns on.)
● Cleaning
(1) Solvent cleaning : Solvent temperature 45°C or less, Immersion for 3 min or less
(2) Ultrasonic cleaning : The effect to device by ultrasonic cleaning differs by cleaning bath size,
ultrasonic power output, cleaning time, PCB size or device mounting condition etc.
Please test it in actual using condition and confirm that any defect doesn’t occur
before starting the ultrasonic cleaning.
(3) Applicable solvent : Ethyl alcohol, Methyl alcohol, Isopropyl alcohol
When the other solvent is used, there are cases that the packaging resin is eroded.
Please use the other solvent after thorough confirmation is performed in actual using condition.
● Precautions for Soldering Phototriac couplers
(1) In case of flow solder (Whole dipping is possible)
It is recommended that flow soldering be carried out at 270°C or less and within 10s
(Pre-heating : 100 to 150°C, 30 to 80s) : Within 2 times
(2) It is recommended that hand soldering be carried out at 400°C or less and within 3s: Within 2 times
(3) Other notes
Depending on equipment and soldering conditions (temperature, Using solder etc.),
the effect to the device and the PCB is different.
Please confirm that there is no problem on the actual use conditions in advance.
Sheet No.: OP14020EN
7
PC3SH13YFZAX
Method of Diagram 1: Breakdown test (Apply to type test and sampling test)
UIOTM
V
t1 , t2
t3 , t4
tp (Partial discharge
(9000V)
= 1 to 10s
= 1s
= 10s
measuring time)
tb
tINI
= 12s
= 60s
t3 , t4
tp (Partial discharge
= 0.1s
= 1s
Upr (1340V)
UIORM (890V)
t3
t1
tINI
t2
tP
t
t4
tb
Method of Diagram 2 : Non breakdown test (Apply to all device test)
V
Upr (1670V)
UIORM (890V)
measuring time)
tb
t3
tp
= 1.2s
t
t4
Fig. 2 Safety maximum forward current
vs. ambient temperature
(When failed)
400
300
200
100
0
0
25
50
75
100
Ambient temperature
125
150
Ta (°C)
250
200
150
100
Isi (mA)
Fig. 1 Safety maximum power dissipation
vs. ambient temperature
(When failed)
500
Safety maximum forward current
Isi (mA)
Safety maximum power dissipation
Psi (mW)
tb
50
0
0
25
50
75
100
Ambient temperature
125
150
Ta (°C)
Sheet No.: OP14020EN
8
PC3SH13YFZAX
■Package specification
● Package materials
No.
Name
Materials
Purposes
①
Sleeve
HIPS or ABS with preventing
Products packaged
static electricity
②
③
④
⑤
Stopper
Packing case
Styrene-Elastomer
Corrugated cardboard
Products fixed
Sleeve packaged
Cushioning material
Kraft tape
Urethane
Paper
Sleeve fixed
Lid of packaged case fixed
⑥
Label
Paper
Model No.,(Business dealing name),
Lot No., Quantity, Country of origin,
Company name and Inspection date specified
● Package method
(1) MAX. 100pcs. of products shall be packaged in a sleeve ① and both of sleeve edges shall be fixed by stoppers ②.
(2) MAX. 20 sleeves (product : 2000pcs.) above shall be packaged in a packing case ③ and pack a sheet of
cushioning material ④ at one side.
(3) The label ⑥ shall be put on the side of the packing case.
(4) Case shall be closed with the lid and enclosed with kraft tape ⑤.
● Sleeve package ① outline dimensions
5.9
10.8
15
8-R0.5
6.35
520±2
(Unit : mm)
Note
1) Thickness : 0.5±0.2mm
2) Process with applying antistatic agent.
3) Unless otherwise specified tolerances shall be ±0.5mm.
(However except for deformation due to the stopper in sleeve.)
Sheet No.: OP14020EN
9
PC3SH13YFZAX
● Packing case outline dimensions
Product
Sleeve ①
Anode mark
Stopper ②
Anode mark shall be
arranged at stopper side
without pulled portion.
Stopper ②
(Without pulled portion)
(With pulled portion)
Cushioning material ④
(1 sheet)
20sleeves (4lines × 5stairs) * MAX
It is disapproved to mix
different model or different
rank model in one case.
Packing case ③
Kraft tape ⑤
Label ⑥
(63mm)
(564mm)
(70mm)
Regular packing mass : Approx. 910g
( ) : Reference dimensions
Sheet No.: OP14020EN
10
PC3SH13YFZAX
■Important Notices
· The circuit application examples in this publication are
provided to explain representative applications of SHARP
devices and are not intended to guarantee any circuit
design or license any intellectual property rights. SHARP
takes no responsibility for any problems related to any
intellectual property right of a third party resulting from
the use of SHARP's devices.
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connection
with equipment that requires an extremely high level of
reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the
specifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability.
Manufacturing locations are also subject to change without
notice.
· If the SHARP devices listed in this publication fall within
the scope of strategic products described in the Foreign
Exchange and Foreign Trade Law of Japan, it is necessary
to obtain approval to export such SHARP devices.
· Observe the following points when using any devices in
this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which does
not meet the conditions and absolute maximum ratings to
be used specified in the relevant specification sheet nor
meet the following conditions:
(i) The devices in this publication are designed for use in
general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
· This publication is the proprietary product of SHARP and
is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be
reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any use
of this publication may be made by a third party.
· Contact and consult with a SHARP representative if there
are any questions about the contents of this publication.
Sheet No.: OP14020EN
11