ACTP-1501

ACTP-1501
Coaxial Tunnel Diode Detector
Data Sheet Revision Date: 12/23/2015
The most important thing we build is trust
DESCRIPTION:
Superior performance and high reliability are designed into these detectors. They offer
extremely stable output voltage over wide temperature excursions, typically +/-0.15dB
from -65°C to +100°C at 1GHz and approx. +/-0.3dB at 18GHz. No bias is required for
operation. Designs are available, in selected frequency bands, from 100MHz (or lower)
to 18GHz. Typical output impedance is in the range of 95 to 125. This allows for fast
pulsed video response and use in wide bandwidth requirements. Video bandwidths may
be modified by selection of the RF bypass capacitor and load value. Square law typically
ranges from TSS up to -17dBm. The upper limit can be raised as high as -13dBm with
selected load values. The output polarity is usually negative but can be made positive if
requested.
SPECIFICATIONS:
Parameter
Specification
Unit of Measure
0.5 – 2
GHz
Sensitivity (min)
800
mV/mW
Flatness vs. Frequency (max)
0.35
±dB
Typical TSS
-51
dBm
2.3:1
Ratio
39
pF
Frequency Range (min)
Typical VSWR
Nominal Video Capacitance
OUTLINE DRAWING:
FEATURES:
•
Contains hermetically sealed modules, internal RF
matching, DC return, and RF bypass capacitor
•
Input impedance matching
•
Models may be chosen for broadband RF performance
of for optimized narrow bands
STANDARD CASE STYLE C3
(Optional Case Styles – C8, C15, C32)
Revised Date: 12/23/2015
(732) 460-0212
www.cobham.com/CSCS
1
ACTP-1501
Coaxial Tunnel Diode Detector
NOTES:
ENVIRONMENTAL SPECIFICATIONS*:
Maximum input power: +14 dBm (3 dB guardband
for +17 dBm possible burnout)
MIL-E-5400, MIL-STD-202, MIL-E-16400
Sensitivity is measured into an open circuit load
(>10k ohm).
Storage Temp: -65°C to +150°C
Operating Temp: -55°C to +125°C
VSWR is measured at or below -20 dBm input power level.
Video capacitance is used for RF bypass. This value can be
changed if required for video response time. Contact the
factory for more information.
SCREENING:
Humidity: MIL-STD-202F, M103, Cond B
Shock: MIL-STD-202F, M213, Cond B
Altitude: MIL-STD-202F, M105, Cond B
Vibration: MIL-STD-202F, M204, Cond B
Thermal Shock: MIL-STD-202F, M107, Cond A
* Compliant by design, verification optional
Internal Visual per MIL-STD-883, Method 2017
Temperature Cycle: -65°C to +100°C, 10 cycles
OPTIONAL HIGH-REL SCREENING
(Ref MIL-PRF-38534):
Stabilization Bake per MIL-STD-883, Method 1008
Temperature Cycle per MIL-STD-883, Method 1010
Constant Acceleration per MIL-STD-883, Method 2001
Burn-in per MIL-STD-883, Method 1015
Leak Test per MIL-STD-883, Method 1014
External Visual per MIL-STD-883, Method 2009
PART NUMBER ORDERING INFORMATION:
Add desired polarity suffix: “N” for Negative, “P” for Positive (Ex: ACTP-1501N)
Add desired case style suffix: “C3” (Ex: ACTP-1501NC3)
Add “R” suffix: Reverse Connector Configuration (Ex: ACTP-1501NC3R) (SMA Female Input/SMA Male Output)
Add “-RC” suffix: RoHS-compliant (Ex: ACTP-1501NZC3-RC)
ISO 9001:2008 and AS9100 certified
For further information please contact:
Aeroflex Control Components, DBA Cobham Signal & Control Solutions (CSCS) reserves the right to make
changes to any products and services herein at any time without notice. Consult CSCS or an authorized sales
representative to verify that the information in this data sheet is current before using this product. CSCS
does not assume any responsibility or liability arising out of the application or use of any product or service
described herein, except as expressly agreed to in writing by CSCS; nor does the purchase, lease, or use of a
product or service from CSCS convey a license under any patent rights, copyrights, trademark rights, or any
other of the intellectual rights of CSCS or of third parties.
Cobham Signal & Control Solutions
40 Industrial Way East
Eatontown , NJ 07724 [USA]
Phone: (732) 460-0212
Fax: (732) 460-0214
[email protected]
Copyright 2015, Cobham Signal & Control Solutions. All rights reserved.
Revised Date: 12/23/2015
(732) 460-0212
www.cobham.com/CSCS
2
Similar pages