4 ADC/8 DAC with PLL, 192 kHz, 24-Bit Codec AD1939 Data Sheet FEATURES GENERAL DESCRIPTION PLL generated or direct master clock Low EMI design 112 dB DAC/107 dB ADC dynamic range and SNR −94 dB THD + N Single 3.3 V supply Tolerance for 5 V logic inputs Supports 24-bits and 8 kHz to 192 kHz sample rates Differential ADC input Differential DAC output Log volume control with autoramp function SPI controllable for flexibility Software-controllable clickless mute Software power-down Right-justified, left-justified, I2S, and TDM modes Master and slave modes up to 16-channel input/output 64-lead LQFP package Qualified for automotive applications The AD1939 is a high performance, single-chip codec that provides four analog-to-digital converters (ADCs) with differential input, and eight digital-to-analog converters (DACs) with differential output using the Analog Devices, Inc. patented multibit sigma-delta (Σ-Δ) architecture. An SPI port is included, allowing a microcontroller to adjust volume and many other parameters. The AD1939 operates from 3.3 V digital and analog supplies. The AD1939 is available in a 64-lead (differential output) LQFP package. The AD1939 is designed for low EMI. This consideration is apparent in both the system and circuit design architectures. By using the on-board PLL to derive the master clock from the LR clock or from an external crystal, the AD1939 eliminates the need for a separate high frequency master clock and can also be used with a suppressed bit clock. The DACs and ADCs are designed using the latest Analog Devices continuous time architectures to further minimize EMI. By using 3.3 V supplies, power consumption is minimized, further reducing emissions. APPLICATIONS Automotive audio systems Home Theater Systems Set-top boxes Digital audio effects processors FUNCTIONAL BLOCK DIAGRAM DIGITAL AUDIO INPUT/OUTPUT AD1939 SERIAL DATA PORT DAC DAC SDATA OUT ADC ANALOG AUDIO INPUTS ADC CLOCKS DIGITAL FILTER ADC SDATA IN TIMING MANAGEMENT AND CONTROL (CLOCK AND PLL) ADC DAC DIGITAL FILTER AND VOLUME CONTROL DAC DAC ANALOG AUDIO OUTPUTS DAC DAC DAC CONTROL DATA INPUT/OUTPUT 06071-001 PRECISION VOLTAGE REFERENCE SPI CONTROL PORT Figure 1. Rev. E Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2006–2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD1939 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Analog-to-Digital Converters (ADCs) .................................... 13 Applications ....................................................................................... 1 Digital-to-Analog Converters (DACs) .................................... 13 General Description ......................................................................... 1 Clock Signals ............................................................................... 13 Functional Block Diagram .............................................................. 1 Reset and Power-Down ............................................................. 14 Revision History ............................................................................... 2 Serial Control Port ..................................................................... 14 Specifications..................................................................................... 3 Power Supply and Voltage Reference....................................... 15 Test Conditions ............................................................................. 3 Serial Data Ports—Data Format ............................................... 15 Analog Performance Specifications ........................................... 3 Time-Division Multiplexed (TDM) Modes ............................ 15 Crystal Oscillator Specifications................................................. 4 Daisy-Chain Mode ..................................................................... 19 Digital Input/Output Specifications........................................... 5 Control Registers ............................................................................ 24 Power Supply Specifications........................................................ 5 Definitions ................................................................................... 24 Digital Filters ................................................................................. 6 PLL and Clock Control Registers ............................................. 24 Timing Specifications .................................................................. 6 DAC Control Registers .............................................................. 25 Absolute Maximum Ratings............................................................ 8 ADC Control Registers .............................................................. 27 Thermal Resistance ...................................................................... 8 Additional Modes ....................................................................... 29 ESD Caution .................................................................................. 8 Application Circuits ....................................................................... 30 Pin Configuration and Function Descriptions ............................. 9 Outline Dimensions ....................................................................... 31 Typical Performance Characteristics ........................................... 11 Ordering Guide .......................................................................... 31 Theory of Operation ...................................................................... 13 Automotive Products ................................................................. 31 REVISION HISTORY 2/13—Rev. D to Rev. E Change to tCLH Parameter, Table 7 ................................................... 7 Changes to Serial Control Port Section ........................................14 7/11—Rev. C to Rev. D Changes to Pin 15, Pin 18, Pin 19, and Pin 20 Descriptions ...... 9 Changes to Pin 26 and Pin 27 Descriptions ................................ 10 9/10—Rev. B to Rev. C Added Qualified for Automotive Applications to the Features Section ................................................................................................ 1 Changed Case Temperature from 130°C to 125°C ...................... 4 Changed TA from −40°C to +130°C to −40°C to +105°C ........... 5 Changed TA from −40°C to +130°C to −40°C to +105°C ........... 7 Changes to Ordering Guide .......................................................... 31 Added Automotive Products Section .......................................... 31 Changes to Ordering Guide .......................................................... 31 6/07—Rev. 0 to Rev. A Deleted I2C References....................................................... Universal Change to Figure 1 ............................................................................1 Changes to Figure 2 ...........................................................................9 Changes to Table 10 ..........................................................................9 Changes to Table 11 ....................................................................... 14 Changes to Table 12 ....................................................................... 16 Changes to Figure 24 and Figure 25............................................. 22 Changes to Table 13 ....................................................................... 23 Change to Figure 26 ....................................................................... 23 Changes to Table 15 and Table 16 ................................................ 24 Changes to Figure 27 and Figure 28............................................. 29 Change to Figure 30 ....................................................................... 30 Updated Outline Dimensions ....................................................... 31 Changes to Ordering Guide .......................................................... 31 7/06—Revision 0: Initial Version 3/10—Rev. A to Rev. B Rev. E | Page 2 of 32 Data Sheet AD1939 SPECIFICATIONS TEST CONDITIONS Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications. Supply voltages (AVDD, DVDD) Temperature range1 Master clock Input sample rate Measurement bandwidth Word width Load capacitance (digital output) Load current (digital output) Input voltage high Input voltage low 1 3.3 V As specified in Table 1 and Table 2 12.288 MHz (48 kHz fS, 256 × fS mode) 48 kHz 20 Hz to 20 kHz 24 bits 20 pF ±1 mA or 1.5 kΩ to ½ DVDD supply 2.0 V 0.8 V Functionally guaranteed at −40°C to +125°C case temperature. ANALOG PERFORMANCE SPECIFICATIONS Specifications guaranteed at an ambient temperature of 25°C. Table 1. Parameter ANALOG-TO-DIGITAL CONVERTERS ADC Resolution Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) Total Harmonic Distortion + Noise Full-Scale Input Voltage (Differential) Gain Error Interchannel Gain Mismatch Offset Error Gain Drift Interchannel Isolation CMRR Input Resistance Input Capacitance Input Common-Mode Bias Voltage DIGITAL-TO-ANALOG CONVERTERS Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) With A-Weighted Filter (Average) Total Harmonic Distortion + Noise Conditions/Comments Min All ADCs 20 Hz to 20 kHz, −60 dB input 96 98 −1 dBFS −10 −0.25 −10 100 mV rms, 1 kHz 100 mV rms, 20 kHz Typ Max Unit 24 Bits 102 105 −96 1.9 dB dB dB V rms % dB mV ppm/°C dB dB dB kΩ pF V 0 100 −110 55 55 14 10 1.5 −87 +10 +0.25 +10 20 Hz to 20 kHz, −60 dB input 102 105 0 dBFS Two channels running Eight channels running Full-Scale Output Voltage Gain Error Interchannel Gain Mismatch Offset Error Gain Drift Interchannel Isolation 107 110 112 −94 −86 1.76 (4.96) −10 −0.2 −25 −30 −6 100 Rev. E | Page 3 of 32 dB dB dB −76 +10 +0.2 +25 +30 dB dB V rms (V p-p) % dB mV ppm/°C dB AD1939 Parameter Interchannel Phase Deviation Volume Control Step Volume Control Range De-emphasis Gain Error Output Resistance at Each Pin REFERENCE Internal Reference Voltage External Reference Voltage Common-Mode Reference Output REGULATOR Input Supply Voltage Regulated Output Voltage Data Sheet Conditions/Comments Min Typ 0 0.375 95 Max ±0.6 100 Unit Degrees dB dB dB Ω FILTR pin FILTR pin CM pin 1.32 1.50 1.50 1.50 1.68 V V V VSUPPLY pin VSENSE pin 4.5 3.19 5 3.37 5.5 3.55 V V Min Typ Specifications measured at a case temperature of 125°C. Table 2. Parameter ANALOG-TO-DIGITAL CONVERTERS ADC Resolution Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) Total Harmonic Distortion + Noise Full-Scale Input Voltage (Differential) Gain Error Interchannel Gain Mismatch Offset Error DIGITAL-TO-ANALOG CONVERTERS Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) With A-Weighted Filter (Average) Total Harmonic Distortion + Noise Full-Scale Output Voltage Gain Error Interchannel Gain Mismatch Offset Error Gain Drift REFERENCE Internal Reference Voltage External Reference Voltage Common-Mode Reference Output REGULATOR Input Supply Voltage Regulated Output Voltage Conditions/Comments All ADCs 20 Hz to 20 kHz, −60 dB input 93 96 −1 dBFS −10 −0.25 −10 Max 24 Bits 102 104 −96 1.9 dB dB dB V rms % dB mV 0 −87 +10 +0.25 +10 20 Hz to 20 kHz, −60 dB input 101 104 0 dBFS Two channels running Eight channels running 107 110 112 −94 −86 1.76 (4.96) −10 −0.2 −25 −30 −6 dB dB dB −70 +10 +0.2 +25 +30 dB dB V rms (V p-p) % dB mV ppm/°C FILTR pin FILTR pin CM pin 1.32 1.50 1.50 1.50 1.68 V V V VSUPPLY pin VSENSE pin 4.5 3.2 5 3.43 5.5 3.65 V V CRYSTAL OSCILLATOR SPECIFICATIONS Table 3. Parameter Transconductance Unit Min Typ 3.5 Rev. E | Page 4 of 32 Max Unit mmhos Data Sheet AD1939 DIGITAL INPUT/OUTPUT SPECIFICATIONS −40°C < TA < +105°C, DVDD = 3.3 V ± 10%. Table 4. Parameter High Level Input Voltage (VIH) Conditions/Comments MCLKI/XI pin Low Level Input Voltage (VIL) Input Leakage High Level Output Voltage (VOH) Low Level Output Voltage (VOL) Input Capacitance IIH @ VIH = 2.4 V IIL @ VIL = 0.8 V IOH = 1 mA IOL = 1 mA Min 2.0 2.2 Typ Max 0.4 5 Unit V V V µA µA V V pF 0.8 10 10 DVDD − 0.60 POWER SUPPLY SPECIFICATIONS Table 5. Parameter SUPPLIES Voltage Digital Current Normal Operation Power-Down Analog Current Normal Operation Power-Down DISSIPATION Operation All Supplies Digital Supply Analog Supply Power-Down, All Supplies POWER SUPPLY REJECTION RATIO Signal at Analog Supply Pins Conditions/Comments Min Typ Max Unit DVDD AVDD VSUPPLY Master clock = 256 fS fS = 48 kHz fS = 96 kHz fS = 192 kHz fS = 48 kHz to 192 kHz 3.0 3.0 4.5 3.3 3.3 5.0 3.6 3.6 5.5 V V V 56 65 95 2.0 mA mA mA mA 74 23 mA mA 429 185 244 83 mW mW mW mW 50 50 dB dB Master clock = 256 fS, 48 kHz 1 kHz, 200 mV p-p 20 kHz, 200 mV p-p Rev. E | Page 5 of 32 AD1939 Data Sheet DIGITAL FILTERS Table 6. Parameter ADC DECIMATION FILTER Pass Band Pass-Band Ripple Transition Band Stop Band Stop-Band Attenuation Group Delay DAC INTERPOLATION FILTER Pass Band Pass-Band Ripple Transition Band Stop Band Stop-Band Attenuation Group Delay Mode All modes, typical @ 48 kHz Factor Min 0.4375 fS Typ Max Unit 21 ±0.015 24 27 0.5 fS 0.5625 fS kHz dB kHz kHz dB µs 79 22.9844/fS 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 48 kHz mode, typical @ 48 kHz 96 kHz mode, typical @ 96 kHz 192 kHz mode, typical @ 192 kHz 0.4535 fS 0.3646 fS 0.3646 fS 479 22 kHz kHz kHz dB dB dB kHz kHz kHz kHz kHz kHz dB dB dB µs µs µs 35 70 ±0.01 ±0.05 ±0.1 0.5 fS 0.5 fS 0.5 fS 0.5465 fS 0.6354 fS 0.6354 fS 24 48 96 26 61 122 70 70 70 25/fS 11/fS 8/fS 521 115 42 TIMING SPECIFICATIONS −40°C < TA < +105°C, DVDD = 3.3 V ± 10%. Table 7. Parameter INPUT MASTER CLOCK (MCLK) AND RESET tMH Condition Comments Min Max Unit MCLK duty cycle DAC/ADC clock source = PLL clock @ 256 fS, 384 fS, 512 fS, and 768 fS DAC/ADC clock source = direct MCLK @ 512 fS (bypass on-chip PLL) PLL mode, 256 fS reference Direct 512 fS mode 40 60 % 40 60 % 6.9 13.8 27.6 MHz MHz ns tMCLK 10 60 ms % tMH fMCLK fMCLK tPDR tPDRR PLL Lock Time 256 fS VCO Clock, Output Duty Cycle, MCLKO/XO Pin MCLK frequency Low Recovery Reset to active output 15 4096 MCLK and LRCLK input 40 Rev. E | Page 6 of 32 Data Sheet Parameter SPI PORT tCCH tCCL fCCLK tCDS tCDH tCLS tCLH tCLHIGH tCOE tCOD tCOH tCOTS DAC SERIAL PORT tDBH tDBL tDLS tDLH tDLS tDDS tDDH ADC SERIAL PORT tABH tABL tALS tALH tALS tABDD AUXILIARY INTERFACE tAXDS tAXDH tDXDD tXBH tXBL tDLS tDLH AD1939 Condition CCLK high CCLK low CCLK frequency CIN setup CIN hold CLATCH setup CLATCH hold CLATCH high COUT enable COUT delay COUT hold COUT tristate DBCLK high DBCLK low DLRCLK setup DLRCLK hold DLRCLK skew DSDATA setup DSDATA hold ABCLK high ABCLK low ALRCLK setup ALRCLK hold ALRCLK skew ASDATA delay AAUXDATA setup AAUXDATA hold DAUXDATA delay AUXBCLK high AUXBCLK low AUXLRCLK setup AUXLRCLK hold Comments See Figure 11 Min Max 35 35 fCCLK = 1/tCCP; only tCCP shown in Figure 11 To CCLK rising From CCLK rising To CCLK rising From CCLK falling Not shown in Figure 11 From CCLK falling From CCLK falling From CCLK falling, not shown in Figure 11 From CCLK falling See Figure 24 Slave mode Slave mode To DBCLK rising, slave mode From DBCLK rising, slave mode From DBCLK falling, master mode To DBCLK rising From DBCLK rising See Figure 25 Slave mode Slave mode To ABCLK rising, slave mode From ABCLK rising, slave mode From ABCLK falling, master mode From ABCLK falling To AUXBCLK rising From AUXBCLK rising From AUXBCLK falling To AUXBCLK rising From AUXBCLK rising Rev. E | Page 7 of 32 10 10 10 10 10 10 30 30 30 30 10 10 10 5 −8 10 5 10 10 10 5 −8 +8 +8 18 10 5 18 10 10 10 5 Unit ns ns MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns AD1939 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 8. Parameter Analog (AVDD) Digital (DVDD) VSUPPLY Input Current (Except Supply Pins) Analog Input Voltage (Signal Pins) Digital Input Voltage (Signal Pins) Operating Temperature Range (Case) Storage Temperature Range Rating −0.3 V to +3.6 V −0.3 V to +3.6 V −0.3 V to +6.0 V ±20 mA –0.3 V to AVDD + 0.3 V −0.3 V to DVDD + 0.3 V −40°C to +125°C −65°C to +150°C θJA represents thermal resistance, junction-to-ambient; θJC represents the thermal resistance, junction-to-case. All characteristics are for a 4-layer board. Table 9. Thermal Resistance Package Type 64-Lead LQFP ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. E | Page 8 of 32 θJA 47 θJC 11.1 Unit °C/W Data Sheet AD1939 51 50 49 AGND 1 48 AGND MCLKI/XI 2 47 FILTR MCLKO/XO 3 46 AGND AGND 4 45 AVDD AVDD 5 44 AGND OL3P 6 43 OR2N OL3N 7 AD1939 42 OR2P OR3P 8 OL2N OR3N TOP VIEW (Not to Scale) 41 9 40 OL2P DIFFERENTIAL OUTPUT OL4P 10 39 OR1N OL4N 11 38 OR1P NC = NO CONNECT 22 23 24 25 26 27 28 29 30 31 32 DVDD 21 CIN 20 COUT 19 ABCLK 18 ALRCLK DVDD 17 ASDATA1 DGND VDRIVE 33 ASDATA2 CCLK DGND 16 VSENSE 34 VSUPPLY CLATCH DSDATA4 15 DLRCLK 35 DBCLK OL1P PD/RST 14 DSDATA1 OL1N 36 DSDATA2 37 DSDATA3 OR4P 12 OR4N 13 06071-021 52 NC 53 AVDD 54 NC 55 ADC1LP 56 CM 57 ADC1RP 58 ADC1LN 59 ADC1RN 60 ADC2LN 61 ADC2LP 62 ADC2RN LF 63 ADC2RP NC 64 AVDD NC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 2. 64-Lead LQFP, Differential Output, Pin Configuration Table 10. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 In/Out I I O I I O O O O O O O O I I/O Mnemonic AGND MCLKI/XI MCLKO/XO AGND AVDD OL3P OL3N OR3P OR3N OL4P OL4N OR4P OR4N PD/RST DSDATA4 16 17 18 I I I/O DGND DVDD DSDATA3 19 I/O DSDATA2 20 21 22 I I/O I/O DSDATA1 DBCLK DLRCLK Description Analog Ground. Master Clock Input/Crystal Oscillator Input. Master Clock Output/Crystal Oscillator Output. Analog Ground. Analog Power Supply. Connect to analog 3.3 V supply. DAC 3 Left Positive Output. DAC 3 Left Negative Output. DAC 3 Right Positive Output. DAC 3 Right Negative Output. DAC 4 Left Positive Output. DAC 4 Left Negative Output. DAC 4 Right Positive Output. DAC 4 Right Negative Output Power-Down Reset (Active Low). DAC Serial Data Input 4. Data input to DAC4 data in/TDM DAC2 data out (dual-line mode)/AUX DAC2 data out (to external DAC2). Digital Ground. Digital Power Supply. Connect to digital 3.3 V supply. DAC Serial Data Input 3. Data input to DAC3 data in/TDM DAC2 data in (dual-line mode)/AUX ADC2 data in (from external ADC2). DAC Serial Data Input 2. Data input to DAC2 data in/TDM DAC data out/AUX ADC1 data in (from external ADC1). DAC Serial Data Input 1. Data input to DAC1 data in/TDM DAC data in/TDM data in. Bit Clock for DACs. LR Clock for DACs. Rev. E | Page 9 of 32 AD1939 Data Sheet Pin No. 23 24 25 26 In/Out I I O I/O Mnemonic VSUPPLY VSENSE VDRIVE ASDATA2 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 O I/O I/O I I/O I I I I O O O O O O O O I I I O I ASDATA1 ABCLK ALRCLK CIN COUT DVDD DGND CCLK CLATCH OL1P OL1N OR1P OR1N OL2P OL2N OR2P OR2N AGND AVDD AGND FILTR AGND NC NC AVDD CM 53 54 55 56 57 58 59 60 61 62 63 64 I I I I I I I I O I I O ADC1LP ADC1LN ADC1RP ADC1RN ADC2LP ADC2LN ADC2RP ADC2RN LF AVDD NC NC Description 5 V Input to Regulator, Emitter of Pass Transistor. 3.3 V Output of Regulator, Collector of Pass Transistor. Drive for Base of Pass Transistor. ADC Serial Data Output 2. Data Output from ADC2/TDM ADC data in/AUX DAC1 data out (to external DAC1). ADC Serial Data Output 1. Data Output from ADC1/TDM ADC data out/TDM data out. Bit Clock for ADCs. LR Clock for ADCs. Control Data Input (SPI). Control Data Output (SPI). Digital Power Supply. Connect to digital 3.3 V supply. Digital Ground. Control Clock Input (SPI). Latch Input for Control Data (SPI). DAC 1 Left Positive Output. DAC 1 Left Negative Output. DAC 1 Right Positive Output. DAC 1 Right Negative Output. DAC 2 Left Positive Output. DAC 2 Left Negative Output. DAC 2 Right Positive Output. DAC 2 Right Negative Output. Analog Ground. Analog Power Supply. Connect to analog 3.3 V supply. Analog Ground. Voltage Reference Filter Capacitor Connection. Bypass with 10 µF||100 nF to AGND. Analog Ground. No Connect. No Connect. Analog Power Supply. Connect to analog 3.3 V supply. Common-Mode Reference Filter Capacitor Connection. Bypass with 47 µF||100 nF to AGND. ADC1 Left Positive Input. ADC1 Left Negative Input. ADC1 Right Positive Input. ADC1 Right Negative Input. ADC2 Left Positive Input. ADC2 Left Negative Input. ADC2 Right Positive Input. ADC2 Right Negative Input. PLL Loop Filter, Return to AVDD. Analog Power Supply. Connect to analog 3.3 V supply. No Connect. No Connect. Rev. E | Page 10 of 32 Data Sheet AD1939 TYPICAL PERFORMANCE CHARACTERISTICS 0.10 0 0.08 0.06 MAGNITUDE (dB) MAGNITUDE (dB) 0.04 0.02 0 –0.02 –0.04 –50 –100 –0.06 –150 0 2 4 6 8 10 12 14 16 06071-002 –0.10 18 FREQUENCY (kHz) 0 12 24 36 48 FREQUENCY (kHz) Figure 3. ADC Pass-Band Filter Response, 48 kHz 06071-005 –0.08 Figure 6. DAC Stop-Band Filter Response, 48 kHz 0 0.10 –10 –20 0.05 MAGNITUDE (dB) MAGNITUDE (dB) –30 –40 –50 –60 –70 0 –0.05 –80 5 10 15 20 25 30 35 –0.10 06071-003 0 40 FREQUENCY (kHz) 0 24 48 72 96 FREQUENCY (kHz) Figure 4. ADC Stop-Band Filter Response, 48 kHz 06071-006 –90 –100 Figure 7. DAC Pass-Band Filter Response, 96 kHz 0.06 0 MAGNITUDE (dB) 0.02 0 –0.02 –50 –100 –150 –0.06 0 8 16 FREQUENCY (kHz) 24 Figure 5. DAC Pass-Band Filter Response, 48 kHz 0 24 48 72 FREQUENCY (kHz) Figure 8. DAC Stop-Band Filter Response, 96 kHz Rev. E | Page 11 of 32 96 06071-007 –0.04 06071-004 MAGNITUDE (dB) 0.04 AD1939 Data Sheet 0.5 0 0.4 0.3 –2 MAGNITUDE (dB) 0.1 0 –0.1 –4 –6 –0.2 –8 –0.3 –0.5 0 8 16 32 64 FREQUENCY (kHz) –10 48 64 80 FREQUENCY (kHz) Figure 10. DAC Stop-Band Filter Response, 192 kHz Figure 9. DAC Pass-Band Filter Response, 192 kHz Rev. E | Page 12 of 32 96 06071-009 –0.4 06071-008 MAGNITUDE (dB) 0.2 Data Sheet AD1939 THEORY OF OPERATION ANALOG-TO-DIGITAL CONVERTERS (ADCS) There are four analog-to-digital converter (ADC) channels in the AD1939 configured as two stereo pairs with differential inputs. The ADCs can operate at a nominal sample rate of 48 kHz, 96 kHz, or 192 kHz. The ADCs include on-board digital antialiasing filters with 79 dB stop-band attenuation and linear phase response, operating at an oversampling ratio of 128 (48 kHz, 96 kHz, and 192 kHz modes). Digital outputs are supplied through two serial data output pins (one for each stereo pair) and a common frame clock (ALRCLK) and bit clock (ABCLK). Alternatively, one of the TDM modes can be used to access up to 16 channels on a single TDM data line. The ADCs must be driven from a differential signal source for best performance. The input pins of the ADCs connect to internal switched capacitors. To isolate the external driving op amp from the glitches caused by the internal switched capacitors, each input pin should be isolated by using a series-connected external 100 Ω resistor together with a 1 nF capacitor connected from each input to ground. This capacitor must be of high quality, for example, ceramic NP0 or polypropylene film. The differential inputs have a nominal common-mode voltage of 1.5 V. The voltage at the common-mode reference pin (CM) can be used to bias external op amps to buffer the input signals (see the Power Supply and Voltage Reference section). The inputs can also be ac-coupled and do not need an external dc bias to CM. A digital high-pass filter can be switched in line with the ADCs under serial control to remove residual dc offsets. It has a 1.4 Hz, 6 dB per octave cutoff at a 48 kHz sample rate. The cutoff frequency scales directly with sample frequency. DIGITAL-TO-ANALOG CONVERTERS (DACS) slew rate or low bandwidth can cause high frequency noise and tones to fold down into the audio band; exercise care in selecting these components. The voltage at CM, the common-mode reference pin, can be used to bias the external op amps that buffer the output signals (see the Power Supply and Voltage Reference section). CLOCK SIGNALS The on-chip phase-locked loop (PLL) can be selected to reference the input sample rate from either of the LRCLK pins or 256, 384, 512, or 768 times the sample rate, referenced to the 48 kHz mode from the MCLKI/XI pin. The default at power-up is 256 × fS from the MCLKI/XI pin. In 96 kHz mode, the master clock frequency stays at the same absolute frequency; therefore, the actual multiplication rate is divided by 2. In 192 kHz mode, the actual multiplication rate is divided by 4. For example, if a device in the AD1939 family is programmed in 256 × fS mode, the frequency of the master clock input is 256 × 48 kHz = 12.288 MHz. If the AD1939 is then switched to 96 kHz operation (by writing to the SPI port), the frequency of the master clock should remain at 12.288 MHz, which is 128 × fS in this example. In 192 kHz mode, this becomes 64 × fS. The internal clock for the ADCs is 256 × fS for all clock modes. The internal clock for the DACs varies by mode: 512 × fS (48 kHz mode), 256 × fS (96 kHz mode), or 128 × fS (192 kHz mode). By default, the on-board PLL generates this internal master clock from an external clock. A direct 512 × fS (referenced to 48 kHz mode) master clock can be used for either the ADCs or DACs if selected in the PLL and Clock Control 1 register. Note that it is not possible to use a direct clock for the ADCs set to the 192 kHz mode. It is required that the on-chip PLL be used in this mode. The AD1939 digital-to-analog converter (DAC) channels are arranged as differential, four stereo pairs giving eight analog outputs for improved noise and distortion performance. The DACs include on-board digital reconstruction filters with 70 dB stop-band attenuation and linear phase response, operating at an oversampling ratio of 4 (48 kHz or 96 kHz modes) or 2 (192 kHz mode). Each channel has its own independently programmable attenuator, adjustable in 255 steps in increments of 0.375 dB. Digital inputs are supplied through four serial data input pins (one for each stereo pair) and a common frame clock (DLRCLK) and bit clock (DBCLK). Alternatively, one of the TDM modes can be used to access up to 16 channels on a single TDM data line. The PLL can be powered down in the PLL and Clock Control 0 register. To ensure reliable locking when changing PLL modes, or if the reference clock is unstable at power-on, power down the PLL and then power it back up when the reference clock stabilizes. Each output pin has a nominal common-mode dc level of 1.5 V and swings ±1.27 V for a 0 dBFS digital input signal. A single op amp, third-order, external, low-pass filter is recommended to remove high frequency noise present on the output pins, as well as to provide differential-to-single-ended conversion in the case of the differential output. Note that the use of op amps with low To maintain the highest performance possible, limit the clock jitter of the internal master clock signal to less than a 300 ps rms time interval error (TIE). Even at these levels, extra noise or tones can appear in the DAC outputs if the jitter spectrum contains large spectral peaks. If the internal PLL is not used, it is best to use an independent crystal oscillator to generate the The internal master clock (MCLK) can be disabled in the PLL and Clock Control 0 register to reduce power dissipation when the AD1939 is idle. The clock should be stable before it is enabled. Unless a standalone mode is selected (see the Serial Control Port section), the clock is disabled by reset and must be enabled by writing to the SPI port for normal operation. Rev. E | Page 13 of 32 AD1939 Data Sheet master clock. In addition, it is especially important that the clock signal not pass through an FPGA, CPLD, or other large digital chip (such as a DSP) before being applied to the AD1939. In most cases, this induces clock jitter due to the sharing of common power and ground connections with other unrelated digital output signals. When the PLL is used, jitter in the reference clock is attenuated above a certain frequency depending on the loop filter. RESET AND POWER-DOWN The function of the RST pin sets all the control registers to their default settings. To avoid pops, reset does not power down the analog outputs. After RST is deasserted and the PLL acquires lock condition, an initialization routine runs inside the AD1939. This initialization lasts for approximately 256 master clock cycles. The power-down bits in the PLL and Clock Control 0, DAC Control 1, and ADC Control 1 registers power down the respective sections. All other register settings are retained. To guarantee proper startup, the RST pin should be pulled low by an external resistor. SERIAL CONTROL PORT for operation without serial control; standalone is configured at reset by connecting CIN, CCLK, and CLATCH to ground. In standalone mode, all registers are set to default, except the internal MCLK enable, which is set to 1. The ADC, ABCLK, and ALRCLK clock ports are set to master/slave by the connecting the COUT pin to either DVDD or ground. Standalone mode only supports stereo mode with an I2S data format and 256 fS MCLK rate. Refer to Table 11 for details. If CIN, CCLK, and CLATCH are not grounded, the AD1939 SPI port is active. It is recommended to use a weak pull-up resistor on CLATCHin applications that have a microcontroller. This pull-up resistor ensures that the AD1939 recognizes the presence of a microcontroller. The SPI control port of the AD1939 is a 4-wire serial control port. The format is similar to the Motorola SPI format except the input data-word is 24 bits wide. The serial bit clock and latch can be completely asynchronous to the sample rate of the ADCs and DACs. Figure 11 shows the format of the SPI signal. The first byte is a global address with a read/write bit. For the AD1939, the address is 0x04, shifted left one bit due to the R/W bit. The second byte is the AD1939 register address and the third byte is the data. The AD1939 has an SPI control port that permits programming and reading back of the internal control registers for the ADCs, DACs, and clock system. A standalone mode is also available Table 11. Standalone Mode Selection ADC Clocks Slave Master CIN 0 0 COUT 0 1 tCLS CLATCH 0 0 tCLH tCCH tCCL tCCP CLATCH CCLK 0 0 tCOTS CCLK tCDS tCDH COUT D23 D22 D9 tCOE D9 D8 D0 D8 D0 06071-010 CIN tCOD Figure 11. Format of the SPI Signal Rev. E | Page 14 of 32 Data Sheet AD1939 POWER SUPPLY AND VOLTAGE REFERENCE The AD1939 is designed for 3.3 V supplies. Separate power supply pins are provided for the analog and digital sections. To minimize noise pickup, these pins should be bypassed with 100 nF ceramic chip capacitors placed as close to the pins as possible. A bulk aluminum electrolytic capacitor of at least 22 μF should also be provided on the same PC board as the codec. For critical applications, improved performance is obtained with separate supplies for the analog and digital sections. If this is not possible, it is recommended that the analog and digital supplies be isolated by means of a ferrite bead in series with each supply. It is important that the analog supply be as clean as possible. The AD1939 includes a 3.3 V regulator driver that only requires an external pass transistor and bypass capacitors to make a 5 V to 3.3 V regulator. If the regulator driver is not used, connect VSUPPLY, VDRIVE, and VSENSE to DGND. polarity of DBCLK and DLRCLK is programmable according to the DAC Control 1 register. The ADC serial formats and serial clock polarity are programmable according to the ADC Control 1 register. Both DAC and ADC serial ports are programmable to become the bus masters according to DAC Control 1 register and ADC Control 2 register. By default, both ADC and DAC serial ports are in the slave mode. TIME-DIVISION MULTIPLEXED (TDM) MODES The AD1939 serial ports also have several different TDM serial data modes. The first and most commonly used configurations are shown in Figure 12 and Figure 13. In Figure 12, the ADC serial port outputs one data stream consisting of four on-chip ADCs followed by four unused slots. In Figure 13, the eight onchip DAC data slots are packed into one TDM stream. In this mode, both DBCLK and ABCLK are 256 fS. LRCLK 256 BCLKs BCLK All digital inputs are compatible with TTL and CMOS levels. All outputs are driven from the 3.3 V DVDD supply and are compatible with TTL and 3.3 V CMOS levels. DATA 32 BCLKs SLOT 1 LEFT 1 SLOT 2 RIGHT 1 SLOT 3 LEFT 2 SLOT 4 RIGHT 2 SLOT 5 SLOT 6 SLOT 7 SLOT 8 LRCLK The ADC and DAC internal voltage reference (VREF) is brought out on FILTR and should be bypassed as close as possible to the chip with a parallel combination of 10 μF and 100 nF. Any external current drawn should be limited to less than 50 μA. The internal reference can be disabled in the PLL and Clock Control 1 register and FILTR can be driven from an external source. This can be used to scale the DAC output to the clipping level of a power amplifier based on its power supply voltage. The ADC input gain varies by the inverse ratio. The total gain from ADC input to DAC output remains constant. MSB MSB–1 MSB–2 06071-016 BCLK DATA Figure 12. ADC TDM (8-Channel I2S Mode) LRCLK 256 BCLKs BCLK DATA 32 BCLKs SLOT 1 LEFT 1 SLOT 2 RIGHT 1 SLOT 3 LEFT 2 SLOT 4 RIGHT 2 SLOT 5 LEFT 3 SLOT 6 RIGHT 3 SLOT 7 LEFT 4 SLOT 8 RIGHT 4 LRCLK SERIAL DATA PORTS—DATA FORMAT The eight DAC channels use a common serial bit clock (DBCLK) and a common left-right framing clock (DLRCLK) in the serial data port. The four ADC channels use a common serial bit clock (ABCLK) and left-right framing clock (ALRCLK) in the serial data port. The clock signals are all synchronous with the sample rate. The normal stereo serial modes are shown in Figure 23. The ADC and DAC serial data modes default to I2S. The ports can also be programmed for left-justified, right-justified, and TDM modes. The word width is 24 bits by default and can be programmed for 16 or 20 bits. The DAC serial formats are programmable according to the DAC Control 0 register. The BCLK MSB MSB–1 MSB–2 DATA 06071-017 The CM pin is the internal common-mode reference. It should be bypassed as close as possible to the chip, with a parallel combination of 47 μF and 100 nF. This voltage can be used to bias external op amps to the common-mode voltage of the input and output signal pins. The output current should be limited to less than 0.5 mA source and 2 mA sink. Figure 13. DAC TDM (8-Channel I2S Mode) The I/O pins of the serial ports are defined according to the serial mode that is selected. For a detailed description of the function of each pin in TDM and AUX modes, see Table 12. The AD1939 allows systems with more than eight DAC channels to be easily configured by the use of an auxiliary serial data port. The DAC TDM-AUX mode is shown in Figure 14. In this mode, the AUX channels are the last four slots of the TDM data stream. These slots are extracted and output to the AUX serial port. It should be noted that due to the high DBCLK frequency, this mode is available only in the 48 kHz/44.1 kHz/32 kHz sample rate. The AD1939 also allows system configurations with more than four ADC channels as shown in Figure 15 (using 8 ADCs) and Figure 16 (using 16 ADCs). Again, due to the high ABCLK frequency, this mode is available only in the 48 kHz/44.1 kHz/32 kHz sample rate. Rev. E | Page 15 of 32 AD1939 Data Sheet Combining the AUX ADC and DAC modes results in a system configuration of 8 ADCs and 12 DACs. The system, then, consists of two external stereo ADCs, two external stereo DACs, and one AD1939. This mode is shown in Figure 17 (combined AUX DAC and ADC modes). Table 12. Pin Function Changes in TDM and AUX Modes Pin Mnemonic ASDATA1 ASDATA2 DSDATA1 DSDATA2 DSDATA3 DSDATA4 ALRCLK ABCLK DLRCLK DBCLK Stereo Modes ADC1 Data Out ADC2 Data Out DAC1 Data In DAC2 Data In DAC3 Data In DAC4 Data In ADC LRCLK In/ADC LRCLK Out ADC BCLK In/ADC BCLK Out DAC LRCLK In/DAC LRCLK Out DAC BCLK In/DAC BCLK Out TDM Modes ADC TDM Data Out ADC TDM Data In DAC TDM Data In DAC TDM Data Out DAC TDM Data In 2 (Dual-Line Mode) DAC TDM Data Out 2 (Dual-Line Mode) ADC TDM Frame Sync In/ADC TDM Frame Sync Out ADC TDM BCLK In/ADC TDM BCLK Out DAC TDM Frame Sync In/DAC TDM Frame Sync Out DAC TDM BCLK In/DAC TDM BCLK Out AUX Modes TDM Data Out AUX Data Out 1 (to Ext. DAC 1) TDM Data In AUX Data In 1 (from Ext. ADC 1) AUX Data In 2 (from Ext. ADC 2) AUX Data Out 2 (to Ext. DAC 2) TDM Frame Sync In/TDM Frame Sync Out TDM BCLK In/TDM BCLK Out AUX LRCLK In/AUX LRCLK Out AUX BCLK In/AUX BCLK Out ALRCLK ABCLK DSDATA1 (TDM_IN) UNUSED SLOTS EMPTY EMPTY EMPTY AUXILIARY DAC CHANNELS APPEAR AT AUX DAC PORTS 8 ON-CHIP DAC CHANNELS EMPTY DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2 32 BITS MSB DLRCLK (AUX PORT) LEFT RIGHT ASDATA2 (AUX1_OUT) MSB MSB DSDATA4 (AUX2_OUT) MSB MSB Figure 14. 16-Channel DAC TDM-AUX Mode Rev. E | Page 16 of 32 06071-051 DBCLK (AUX PORT) Data Sheet AD1939 ALRCLK ABCLK 8 ON-CHIP DAC CHANNELS DSDATA1 (TDM_IN) DAC L1 ASDATA1 (TDM_OUT) ADC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 ADC R2 AUX L1 AUX R1 4 ON-CHIP ADC CHANNELS ADC R1 DAC L4 DAC R4 4 AUX ADC CHANNELS ADC L2 AUX L2 AUX R2 32 BITS MSB DLRCLK (AUX PORT) LEFT RIGHT DSDATA2 (AUX1_IN) MSB MSB DSDATA3 (AUX2_IN) MSB MSB 06071-050 DBCLK (AUX PORT) Figure 15. 8-Channel AUX ADC Mode ALRCLK ABCLK ASDATA1 (TDM_OUT) 4 ON-CHIP ADC CHANNELS ADC L1 ADC R1 ADC L2 AUXILIARY ADC CHANNELS ADC R2 AUX L1 AUX R1 AUX L2 UNUSED SLOTS AUX R2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 32 BITS MSB DLRCLK (AUX PORT) LEFT RIGHT DBCLK (AUX PORT) MSB DSDATA3 (AUX2_IN) MSB MSB MSB Figure 16. 16-Channel AUX ADC Mode Rev. E | Page 17 of 32 06071-052 DSDATA2 (AUX1_IN) AD1939 Data Sheet ALRCLK ABCLK UNUSED SLOTS DSDATA1 (TDM_IN) EMPTY ASDATA1 (TDM_OUT) ADC L1 DLRCLK (AUX PORT) EMPTY EMPTY EMPTY 4 ON-CHIP ADC CHANNELS ADC R1 ADC L2 AUXILIARY DAC CHANNELS APPEAR AT AUX DAC PORTS 8 ON-CHIP DAC CHANNELS ADC R2 DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 AUXILIARY ADC CHANNELS AUX L1 AUX R1 AUX L2 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2 UNUSED SLOTS AUX R2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED LEFT RIGHT DSDATA2 (AUX1_IN) MSB MSB DSDATA3 (AUX2_IN) MSB MSB ASDATA2 (AUX1_OUT) MSB MSB DSDATA4 (AUX2_OUT) MSB MSB Figure 17. Combined AUX DAC and ADC Mode Rev. E | Page 18 of 32 06071-053 DBCLK (AUX PORT) Data Sheet AD1939 There are two configurations for the ADC port to work in daisy-chain mode. The first one is with an ABCLK at 256 fS shown in Figure 21. The second configuration is shown in Figure 22. Note that in the 512 fS ABCLK mode, the ADC channels occupy the first eight slots; the second eight slots are empty. The TDM_IN of the first AD1939 must be grounded in all modes of operation. DAISY-CHAIN MODE The AD1939 also allows a daisy-chain configuration to expand the system to 8 ADCs and 16 DACs (see Figure 18). In this mode, the DBCLK frequency is 512 fS. The first eight slots of the DAC TDM data stream belong to the first AD1939 in the chain and the last eight slots belong to the second AD1939. The second AD1939 is the device attached to the DSP TDM port. The I/O pins of the serial ports are defined according to the serial mode selected. See Table 13 for a detailed description of the function of each pin. See Figure 26 for a typical AD1939 configuration with two external stereo DACs and two external stereo ADCs. To accommodate 16 channels at a 96 kHz sample rate, the AD1939 can be configured into a dual-line, TDM mode as shown in Figure 19. This mode allows a slower DBCLK than normally required by the one-line TDM mode. Again, the first four channels of each TDM input belong to the first AD1939 in the chain and the last four channels belong to the second AD1939. Figure 23 through Figure 25 show the serial mode formats. For maximum flexibility, the polarity of LRCLK and BCLK are programmable. In these figures, all of the clocks are shown with their normal polarity. The default mode is I2S. The dual-line TDM mode can also be used to send data at a 192 kHz sample rate into the AD1939 as shown in Figure 20. DLRCLK DBCLK 8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN DSDATA1 (TDM_IN) OF THE SECOND AD1939 DAC L1 DAC R1 DAC L2 DSDATA2 (TDM_OUT) OF THE SECOND AD1939 THIS IS THE TDM TO THE FIRST AD1939 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 8 UNUSED SLOTS FIRST AD1939 SECOND AD1939 DSP MSB Figure 18. Single-Line DAC TDM Daisy-Chain Mode (Applicable to 48 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain) Rev. E | Page 19 of 32 06071-054 32 BITS AD1939 Data Sheet DLRCLK DBCLK 8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN DSDATA1 (IN) DAC L1 DAC R1 DAC L2 8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN DAC R2 DSDATA2 (OUT) DSDATA3 (IN) DAC L3 DAC R3 DAC L4 DAC R4 DSDATA4 (OUT) DAC L1 DAC R1 DAC L2 DAC R2 DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 DAC L3 DAC R3 DAC L4 DAC R4 32 BITS FIRST AD1939 SECOND AD1939 06071-055 MSB DSP Figure 19. Dual-Line DAC TDM Mode (Applicable to 96 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain); DSDATA3 and DSDATA4 Are the Daisy Chain DLRCLK DBCLK DSDATA1 DAC L1 DAC R1 DAC L2 DAC R2 DSDATA2 DAC L3 DAC R3 DAC L4 DAC R4 06071-058 32 BITS MSB Figure 20. Dual-Line DAC TDM Mode (Applicable to 192 kHz Sample Rate, 8-Channel Mode) ALRCLK ABCLK 4 ADC CHANNELS OF SECOND IC IN THE CHAIN ASDATA1 (TDM_OUT OF THE SECOND AD1939 IN THE CHAIN) ADC L1 ADC R1 ADC L2 ADC R2 ASDATA2 (TDM_IN OF THE SECOND AD1939 IN THE CHAIN) ADC L1 ADC R1 ADC L2 ADC R2 4 ADC CHANNELS OF FIRST IC IN THE CHAIN ADC L1 ADC R1 ADC L2 ADC R2 32 BITS SECOND AD1939 DSP MSB Figure 21. ADC TDM Daisy-Chain Mode (256 fS ABCLK, Two-AD1939 Daisy Chain) Rev. E | Page 20 of 32 06071-056 FIRST AD1939 Data Sheet AD1939 ALRCLK ABCLK 4 ADC CHANNELS OF SECOND IC IN THE CHAIN 4 ADC CHANNELS OF FIRST IC IN THE CHAIN ASDATA1 (TDM_OUT OF THE SECOND AD1939 IN THE CHAIN) ADC L1 ADC R1 ADC L2 ADC R2 ASDATA2 (TDM_IN OF THE SECOND AD1939 IN THE CHAIN) ADC L1 ADC R1 ADC L2 ADC R2 ADC L1 ADC R1 ADC L2 ADC R2 32 BITS SECOND AD1939 DSP 06071-057 FIRST AD1939 MSB Figure 22. ADC TDM Daisy-Chain Mode (512 fS ABCLK, Two-AD1939 Daisy Chain) LEFT CHANNEL LRCLK RIGHT CHANNEL BCLK SDATA LSB MSB LSB MSB LEFT-JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL LEFT CHANNEL LRCLK RIGHT CHANNEL BCLK SDATA LSB MSB LSB MSB I2S-JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL LEFT CHANNEL LRCLK RIGHT CHANNEL BCLK SDATA MSB LSB MSB LSB RIGHT-JUSTIFIED MODE—SELECT NUMBER OF BITS PER CHANNEL LRCLK BCLK MSB MSB LSB LSB DSP MODE—16 BITS TO 24 BITS PER CHANNEL 1/fS NOTES 1. DSP MODE DOES NOT IDENTIFY CHANNEL. 2. LRCLK NORMALLY OPERATES AT fS EXCEPT FOR DSP MODE, WHICH IS 2 × fS. 3. BCLK FREQUENCY IS NORMALLY 64 × LRCLK BUT MAY BE OPERATED IN BURST MODE. Figure 23. Stereo Serial Modes Rev. E | Page 21 of 32 06071-013 SDATA AD1939 Data Sheet tDBH DBCLK tDBL tDLH tDLS DLRCLK tDDS DSDATAx LEFT-JUSTIFIED MODE MSB MSB–1 tDDH tDDS DSDATAx I2S-JUSTIFIED MODE MSB tDDH tDDS MSB LSB tDDH tDDH 06071-014 tDDS DSDATAx RIGHT-JUSTIFIED MODE Figure 24. DAC Serial Timing tABH ABCLK tABL tALH tALS ALRCLK tABDD ASDATAx LEFT-JUSTIFIED MODE MSB MSB–1 tABDD ASDATAx I2S-JUSTIFIED MODE MSB ASDATAx RIGHT-JUSTIFIED MODE MSB Figure 25. ADC Serial Timing Rev. E | Page 22 of 32 LSB 06071-015 tABDD Data Sheet AD1939 Table 13. Pin Function Changes in TDM and AUX Modes (Replication of Table 12) Stereo Modes ADC1 Data Out ADC2 Data Out DAC1 Data In DAC2 Data In DAC3 Data In DAC4 Data In ADC LRCLK In/ADC LRCLK Out ADC BCLK In/ADC BCLK Out DAC LRCLK In/DAC LRCLK Out DAC BCLK In/DAC BCLK Out TDM Modes ADC TDM Data Out ADC TDM Data In DAC TDM Data In DAC TDM Data Out DAC TDM Data In 2 (Dual-Line Mode) DAC TDM Data Out 2 (Dual-Line Mode) ADC TDM Frame Sync In/ADC TDM Frame Sync Out ADC TDM BCLK In/ADC TDM BCLK Out DAC TDM Frame Sync In/DAC TDM Frame Sync Out DAC TDM BCLK In/DAC TDM BCLK Out TxDATA TxCLK TFS (NC) RxDATA SHARC® RxCLK 12.288MHz LRCLK AUX ADC 1 LRCLK BCLK DATA MCLK AUX Modes TDM Data Out AUX Data Out 1 (to Ext. DAC 1) TDM Data In AUX Data In 1 (from Ext. ADC 1) AUX Data In 2 (from Ext. ADC 2) AUX Data Out 2 (to Ext. DAC 2) TDM Frame Sync In/TDM Frame Sync Out TDM BCLK In/TDM BCLK Out AUX LRCLK In/AUX LRCLK Out AUX BCLK In/AUX BCLK Out SHARC IS RUNNING IN SLAVE MODE (INTERRUPT-DRIVEN) 30MHz FSYNC-TDM (RFS) BCLK ASDATA1 ALRCLK ABCLK DSDATA1 AUX DATA DAC 1 MCLK DBCLK DLRCLK LRCLK AUX ADC 2 BCLK DSDATA2 DATA DSDATA3 MCLK MCLKI/XI AD1939 TDM MASTER AUX MASTER LRCLK ASDATA2 DSDATA4 BCLK AUX DATA DAC 2 MCLK Figure 26. Example of AUX Mode Connection to SHARC (AD1939 as TDM Master/AUX Master Shown) Rev. E | Page 23 of 32 06071-019 Pin Mnemonic ASDATA1 ASDATA2 DSDATA1 DSDATA2 DSDATA3 DSDATA4 ALRCLK ABCLK DLRCLK DBCLK AD1939 Data Sheet CONTROL REGISTERS DEFINITIONS The global address for the AD1939 is 0x04, shifted left one bit due to the R/W bit. All registers are reset to 0, except for the DAC volume registers that are set to full volume. Note that the first setting in each control register parameter is the default setting. Table 14. Register Format Bit Global Address R/W Register Address Data 23:17 16 15:8 7:0 Table 15. Register Addresses and Functions Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Function PLL and Clock Control 0 PLL and Clock Control 1 DAC Control 0 DAC Control 1 DAC Control 2 DAC individual channel mutes DAC L1 volume control DAC R1 volume control DAC L2 volume control DAC R2 volume control DAC L3 volume control DAC R3 volume control DAC L4 volume control DAC R4 volume control ADC Control 0 ADC Control 1 ADC Control 2 PLL AND CLOCK CONTROL REGISTERS Table 16. PLL and Clock Control 0 Register Bit 0 2:1 4:3 6:5 7 Value 0 1 00 01 10 11 00 01 10 11 00 01 10 11 0 1 Function Normal operation Power-down INPUT 256 (× 44.1 kHz or 48 kHz) INPUT 384 (× 44.1 kHz or 48 kHz) INPUT 512 (× 44.1 kHz or 48 kHz) INPUT 768 (× 44.1 kHz or 48 kHz) XTAL oscillator enabled 256 × fS VCO output 512 × fS VCO output Off MCLKI/XI DLRCLK ALRCLK Reserved Disable: ADC and DAC idle Enable: ADC and DAC active Description PLL power-down MCLKI/XI pin functionality (PLL active), master clock rate setting MCLKO/XO pin, master clock rate setting PLL input Internal master clock enable Rev. E | Page 24 of 32 Data Sheet AD1939 Table 17. PLL and Clock Control 1 Register Bit 0 1 2 3 7:4 Value 0 1 0 1 0 1 0 1 0000 Function PLL clock MCLK PLL clock MCLK Enabled Disabled Not locked Locked Reserved Description DAC clock source select ADC clock source select On-chip voltage reference PLL lock indicator (read only) DAC CONTROL REGISTERS Table 18. DAC Control 0 Register Bit 0 2:1 5:3 7:6 Value 0 1 00 01 10 11 000 001 010 011 100 101 110 111 00 01 10 11 Function Normal Power-down 32 kHz/44.1 kHz/48 kHz 64 kHz/88.2 kHz/96 kHz 128 kHz/176.4 kHz/192 kHz Reserved 1 0 8 12 16 Reserved Reserved Reserved Stereo (normal) TDM (daisy chain) DAC AUX mode (ADC-, DAC-, TDM-coupled) Dual-line TDM Description Power-down Sample rate SDATA delay (BCLK periods) Serial format Table 19. DAC Control 1 Register Bit 0 2:1 3 4 5 6 7 Value 0 1 00 01 10 11 0 1 0 1 0 1 0 1 0 1 Function Latch in mid cycle (normal) Latch in at end of cycle (pipeline) 64 (2 channels) 128 (4 channels) 256 (8 channels) 512 (16 channels) Left low Left high Slave Master Slave Master DBCLK pin Internally generated Normal Inverted Description BCLK active edge (TDM in) BCLKs per frame LRCLK polarity LRCLK master/slave BCLK master/slave BCLK source BCLK polarity Rev. E | Page 25 of 32 AD1939 Data Sheet Table 20. DAC Control 2 Register Bit 0 2:1 4:3 5 7:6 Value 0 1 00 01 10 11 00 01 10 11 0 1 00 Function Unmute Mute Flat 48 kHz curve 44.1 kHz curve 32 kHz curve 24 20 Reserved 16 Noninverted Inverted Reserved Description Master mute De-emphasis (32 kHz/44.1 kHz/48 kHz mode only) Word width DAC output polarity Table 21. DAC Individual Channel Mutes Bit 0 1 2 3 4 5 6 7 Value 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Function Unmute Mute Unmute Mute Unmute Mute Unmute Mute Unmute Mute Unmute Mute Unmute Mute Unmute Mute Description DAC 1 left mute DAC 1 right mute DAC 2 left mute DAC 2 right mute DAC 3 left mute DAC 3 right mute DAC 4 left mute DAC 4 right mute Table 22. DAC Volume Controls Bit 7:0 Value 0 1 to 254 255 Function No attenuation −3/8 dB per step Full attenuation Description DAC volume control Rev. E | Page 26 of 32 Data Sheet AD1939 ADC CONTROL REGISTERS Table 23. ADC Control 0 Register Bit 0 1 2 3 4 5 7:6 Value 0 1 0 1 0 1 0 1 0 1 0 1 00 01 10 11 Function Normal Power down Off On Unmute Mute Unmute Mute Unmute Mute Unmute Mute 32 kHz/44.1 kHz/48 kHz 64 kHz/88.2 kHz/96 kHz 128 kHz/176.4 kHz/192 kHz Reserved Description Power-down High-pass filter ADC 1L mute ADC 1R mute ADC 2L mute ADC 2R mute Output sample rate Table 24. ADC Control 1 Register Bit 1:0 4:2 6:5 7 Value 00 01 10 11 000 001 010 011 100 101 110 111 00 01 10 11 0 1 Function 24 20 Reserved 16 1 0 8 12 16 Reserved Reserved Reserved Stereo TDM (daisy chain) ADC AUX mode (ADC-, DAC-, TDM-coupled) Reserved Latch in mid cycle (normal) Latch in at end of cycle (pipeline) Rev. E | Page 27 of 32 Description Word width SDATA delay (BCLK periods) Serial format BCLK active edge (TDM in) AD1939 Data Sheet Table 25. ADC Control 2 Register Bit 0 1 2 3 5:4 6 7 Value 0 1 0 1 0 1 0 1 00 01 10 11 0 1 0 1 Function 50/50 (allows 32, 24, 20, or 16 bit clocks (BCLKs) per channel) Pulse (32 BCLKs per channel) Drive out on falling edge (DEF) Drive out on rising edge Left low Left high Slave Master 64 128 256 512 Slave Master ABCLK pin Internally generated Rev. E | Page 28 of 32 Description LRCLK format BCLK polarity LRCLK polarity LRCLK master/slave BCLKs per frame BCLK master/slave BCLK source Data Sheet AD1939 ADDITIONAL MODES The AD1939 offers several additional modes for board level design enhancements. To reduce the EMI in board level design, serial data can be transmitted without an explicit BCLK. See Figure 27 for an example of a DAC TDM data transmission mode that does not require high speed DBCLK. This configuration is applicable when the AD1939 master clock is generated by the PLL with the DLRCLK as the PLL reference frequency. To relax the requirement for the setup time of the AD1939 in cases of high speed TDM data transmission, the AD1939 can latch in the data using the falling edge of DBCLK. This effectively dedicates the entire BCLK period to the setup time. This mode is useful in cases where the source has a large delay time in the serial data driver. Figure 28 shows this pipeline mode of data transmission. Both the BCLK-less and pipeline modes are available on the ADC serial data port. DLRCLK 32 BITS INTERNAL DBCLK DSDATAx DLRCLK 06071-059 INTERNAL DBCLK TDM-DSDATAx Figure 27. Serial DAC Data Transmission in TDM Format Without DBCLK (Applicable Only If PLL Locks to DLRCLK, This Mode Is Also Available in the ADC Serial Data Port) DLRCLK DBCLK DSDATAx 06071-060 DATA MUST BE VALID AT THIS BCLK EDGE MSB Figure 28. I2S Pipeline Mode in DAC Serial Data Transmission (Applicable in Stereo and TDM, Useful for High Frequency TDM Transmission, This Mode Is Also Available in the ADC Serial Data Port) Rev. E | Page 29 of 32 AD1939 Data Sheet APPLICATION CIRCUITS Typical application circuits are shown in Figure 29 through Figure 32. Figure 29 shows a typical ADC input filter circuit. Recommended loop filters for LR clock and master clock as the PLL reference are shown in Figure 30. Output filters for the DAC outputs are shown in Figure 31 and a regulator circuit is shown in Figure 32. 120pF 5.76kΩ 5.76kΩ 100pF 3 11kΩ – 1 OP275 DAC OUTN + 4.7µF 237Ω 5.76kΩ + 120pF 6 5 OP275 ADCxN DAC OUTP 1nF NPO 1nF NPO 4.7µF 237Ω 7 270pF NPO 5.62kΩ + 2.2nF AVDD2 604Ω + + AUDIO OUTPUT 2.2nF NPO 10µF 5V 1kΩ E B VDRIVE 390pF 562Ω 1 VSUPPLY 5.6nF 3.32kΩ AVDD2 MCLK FZT953 C 06071-030 + LF 39nF 3 – OP275 1.50kΩ 100nF LF 2 Figure 31. Typical DAC Output Filter Circuit (Differential) Figure 29. Typical ADC Input Filter Circuit LRCLK 68pF NPO 5.62kΩ ADCxP + 3.01kΩ 560pF NPO 100pF 5.76kΩ – 11kΩ 06071-031 2 3.3V VSENSE 100nF Figure 30. Recommended Loop Filters for LRCLK or MCLK PLL Reference Rev. E | Page 30 of 32 + 10µF 06071-032 600Z 06071-029 AUDIO INPUT Figure 32. Recommended 3.3 V Regulator Circuit Data Sheet AD1939 OUTLINE DIMENSIONS 0.75 0.60 0.45 12.20 12.00 SQ 11.80 1.60 MAX 64 49 1 48 PIN 1 10.20 10.00 SQ 9.80 TOP VIEW (PINS DOWN) 0.15 0.05 SEATING PLANE 0.20 0.09 7° 3.5° 0° 0.08 COPLANARITY VIEW A 16 33 32 17 VIEW A 0.50 BSC LEAD PITCH 0.27 0.22 0.17 ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BCD 051706-A 1.45 1.40 1.35 Figure 33. 64-Lead Low Profile Quad Flat Package [LQFP] (ST-64-2) Dimensions shown in millimeters ORDERING GUIDE Model 1, 2 AD1939YSTZ AD1939YSTZRL AD1939WBSTZ AD1939WBSTZ-RL EVAL-AD1939AZ 1 2 Temperature Range –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C Package Description 64-Lead LQFP 64-Lead LQFP, 13” Tape and Reel 64-Lead LQFP 64-Lead LQFP, 13” Tape and Reel Evaluation Board Package Option ST-64-2 ST-64-2 ST-64-2 ST-64-2 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD1939W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. E | Page 31 of 32 AD1939 Data Sheet NOTES ©2006–2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06071-0-2/13(E) Rev. E | Page 32 of 32