PDF Data Sheet Rev. D

12-Bit, 160 MSPS, 2×/4×/8× Interpolating
Dual TxDAC D/A Converter
AD9773
FEATURES
Versatile input data interface
Twos complement/straight binary data coding
Dual-port or single-port interleaved input data
Single 3.3 V supply operation
Power dissipation: typical 1.2 W @ 3.3 V
On-chip 1.2 V reference
80-lead thin quad flat package, exposed pad (TQFP_EP)
12-bit resolution, 160 MSPS/400 MSPS
input/output data rate
Selectable 2×/4×/8× interpolating filter
Programmable channel gain and offset adjustment
fS/2, fS/4, fS/8 digital quadrature modulation capability
Direct IF transmission mode for 70 MHz + IFs
Enables image rejection architecture
Fully compatible SPI port
Excellent ac performance
SFDR −69 dBc @ 2 MHz to 35 MHz
WCDMA ACPR −69 dB @ IF = 19.2 MHz
Internal PLL clock multiplier
Selectable internal clock divider
Versatile clock input
Differential/single-ended sine wave or
TTL/CMOS/LVPECL compatible
APPLICATIONS
Communications
Analog quadrature modulation architecture
3G, multicarrier GSM, TDMA, CDMA systems
Broadband wireless, point-to-point microwave radios
Instrumentation/ATE
FUNCTIONAL BLOCK DIAGRAM
IDAC
COS
AD9773
I AND Q
NONINTERLEAVED
OR INTERLEAVED
DATA
12
WRITE
SELECT
GAIN
DAC
OFFSET
DAC
SIN
I
LATCH
16
Q
LATCH
16
MUX
CONTROL
HALFBAND
FILTER3*
16
16
16
fDAC/2, 4, 8
16
16
SIN
16
FILTER
BYPASS
MUX
IMAGE
REJECTION/
DUAL DAC
MODE
BYPASS
MUX
I/Q DAC
GAIN/OFFSET
REGISTERS
IOFFSET
12
HALFBAND
FILTER2*
VREF
DATA
ASSEMBLER
HALFBAND
FILTER1*
COS
IDAC
/2
IOUT
(fDAC)
CLOCK OUT
/2
/2
/2
SPI INTERFACE AND
CONTROL REGISTERS
DIFFERENTIAL
CLK
PHASE DETECTOR
AND VCO
PLL CLOCK MULTIPLIER AND CLOCK DIVIDER
02857-001
* HALF-BAND FILTERS ALSO CAN BE
CONFIGURED FOR ZERO STUFFING ONLY
PRESCALER
Figure 1.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
AD9773
TABLE OF CONTENTS
Features .............................................................................................. 1
Two-Port Data Input Mode ...................................................... 30
Applications....................................................................................... 1
One-/Two-Port Input Modes.................................................... 30
Functional Block Diagram .......................................................... 1
PLL Enabled, Two-Port Mode .................................................. 30
Table of Contents .............................................................................. 2
DATACLK Inversion.................................................................. 31
Revision History ........................................................................... 2
DATACLK Driver Strength....................................................... 31
General Description ......................................................................... 4
PLL Enabled, One-Port Mode .................................................. 31
Product Highlights ....................................................................... 4
ONEPORTCLK Inversion......................................................... 31
Specifications..................................................................................... 5
ONEPORTCLK Driver Strength.............................................. 32
DC Specifications ......................................................................... 5
IQ Pairing .................................................................................... 32
Dynamic Specifications ............................................................... 6
PLL Disabled, Two-Port Mode................................................. 32
Digital Specifications ................................................................... 7
PLL Disabled, One-Port Mode ................................................. 32
Digital Filter Specifications ......................................................... 8
Digital Filter Modes ................................................................... 33
Absolute Maximum Ratings............................................................ 9
Amplitude Modulation.............................................................. 33
Thermal Characteristics .............................................................. 9
Modulation, No Interpolation .................................................. 34
ESD Caution.................................................................................. 9
Modulation, Interpolation = 2× ............................................... 35
Pin Configuration and Function Descriptions........................... 10
Modulation, Interpolation = 4× ............................................... 36
Typical Performance Characteristics ........................................... 12
Modulation, Interpolation = 8× ............................................... 37
Terminology .................................................................................... 17
Zero Stuffing ............................................................................... 38
Mode Control (Via SPI Port) .................................................... 18
Interpolating (Complex Mix Mode)........................................ 38
Register Description................................................................... 20
Operations on Complex Signals............................................... 38
Functional Description .................................................................. 22
Complex Modulation and Image Rejection of Baseband
Signals .......................................................................................... 39
Serial Interface for Register Control ........................................ 22
General Operation of the Serial Interface ............................... 22
Instruction Byte .......................................................................... 23
Serial Interface Port Pin Descriptions ..................................... 23
MSB/LSB Transfers..................................................................... 23
Notes on Serial Port Operation ................................................ 25
DAC Operation........................................................................... 25
Image Rejection and Sideband Suppression of Modulated
Carriers ........................................................................................ 41
Applying the Output Configurations........................................... 46
Unbuffered Differential Output, Equivalent Circuit ............. 46
Differential Coupling Using a Transformer............................ 46
Differential Coupling Using an Op Amp................................ 47
1R/2R Mode ................................................................................ 26
Interfacing the AD9773 with the AD8345 Quadrature
Modulator.................................................................................... 47
Clock Input Configurations ...................................................... 27
Evaluation Board ............................................................................ 48
Programmable PLL .................................................................... 27
Outline Dimensions ....................................................................... 58
Power Dissipation....................................................................... 29
Ordering Guide .......................................................................... 58
Sleep/Power-Down Modes........................................................ 29
REVISION HISTORY
10/07—Rev. C to Rev. D
Updated Formatting ........................................................ Universal
Changes to Figure 32 .................................................................... 22
Changes to Figure 108 .................................................................. 54
Updated Outline Dimensions ..................................................... 58
Changes to Ordering Guide......................................................... 58
Rev. D | Page 2 of 60
AD9773
1/06—Rev. B to Rev. C
Updated Formatting .........................................................Universal
Changes to Figure 32 .................................................................... 22
Changes to Figure 108 .................................................................. 55
Updated Outline Dimensions ..................................................... 58
Changes to Ordering Guide......................................................... 58
4/04—Data Sheet Changed from Rev. A to Rev. B.
Update Layout....................................................................Universal
Changes to DC Specifications ....................................................... 5
Changes to Absolute Maximum Ratings...................................... 9
Changes to DAC Operation Section........................................... 25
Inserted Figure 38.......................................................................... 25
Changes to Figure 40 .................................................................... 26
Changes to Table 11 ...................................................................... 28
Changes to Programmable PLL Section..................................... 29
Changes to Power Dissipation Section....................................... 29
Changes to Figures 49, 50, and 51............................................... 29
Changes to PLL Enabled, One-Port Mode Section .................. 31
Changes to PLL Disabled, One-Port Mode Section ................. 32
Changes to Figure 102 .................................................................. 49
Changes to Figure 104 .................................................................. 50
Updated Ordering Guide ............................................................. 58
Updated Outline Dimensions...................................................... 58
3/03—Data Sheet Changed from Rev. 0 to Rev. A.
Edits to Features ...............................................................................1
Edits to DC Specifications ..............................................................3
Edits to Dynamic Specifications ....................................................4
Edits to Pin Function Descriptions ...............................................7
Edits to Table I ............................................................................... 14
Edits to Register Description—Address 02h Section............... 15
Edits to Register Description—Address 03h Section............... 16
Edits to Register Description—Address 07h, 0Bh Section...... 16
Edits to Equation 1........................................................................ 16
Edits to MSB/LSB Transfers Section........................................... 18
Changes to Figure 8 ...................................................................... 20
Edits to Programmable PLL Section........................................... 21
Added New Figure 14 ................................................................... 22
Renumbered Figures 15 through 69 ........................................... 22
Add Two-Port Data Input Mode Section................................... 23
Edits to PLL Enabled, Two-Port Mode Section ........................ 24
Edits to Figure 19 .......................................................................... 24
Edits to Figure 21 .......................................................................... 25
Edits to PLL Disabled, Two-Port Mode Section ....................... 25
Edits to Figure 22 .......................................................................... 25
Edits to Figure 23 .......................................................................... 26
Edits to Figure 26a ........................................................................ 27
Edits to Complex Modulation and Image Rejection of
Baseband Signals Section ............................................................. 31
Changes to Figures 53 and 54...................................................... 38
Edits to Evaluation Board Section .............................................. 39
Changes to Figures 56 through 59 .............................................. 40
Replaced Figures 60 through 69.................................................. 42
Updated Outline Dimensions...................................................... 49
Rev. D | Page 3 of 60
AD9773
GENERAL DESCRIPTION
The AD9773 1 is the 12-bit member of the AD977x pincompatible, high performance, programmable 2×/4×/8×
interpolating TxDAC+® family. The AD977x family features
a serial port interface (SPI) that provides a high level of
programmability, thus allowing for enhanced system-level
options. These options include selectable 2×/4×/8× interpolation filters; fS/2, fS/4, or fS/8 digital quadrature modulation
with image rejection; a direct IF mode; programmable channel
gain and offset control; programmable internal clock divider;
straight binary or twos complement data interface; and a singleport or dual-port data interface.
The selectable 2×/4×/8× interpolation filters simplify the
requirements of the reconstruction filters while simultaneously
enhancing the TxDAC+ family’s pass-band noise/distortion
performance. The independent channel gain and offset adjust
registers allow the user to calibrate LO feedthrough and sideband suppression errors associated with analog quadrature
modulators. The 6 dB of gain adjustment range can also be
used to control the output power level of each DAC.
The AD9773 features the ability to perform fS/2, fS/4, and fS/8
digital modulation and image rejection when combined with an
analog quadrature modulator. In this mode, the AD9773
accepts I and Q complex data (representing a single or multicarrier waveform), generates a quadrature modulated IF signal
along with its orthogonal representation via its dual DACs, and
presents these two reconstructed orthogonal IF carriers to an
analog quadrature modulator to complete the image rejection
upconversion process. Another digital modulation mode (for
example, the direct IF mode) allows the original baseband
signal representation to be frequency translated such that pairs
of images fall at multiples of one-half the DAC update rate.
The AD977x family includes a flexible clock interface accepting
differential or single-ended sine wave or digital logic inputs.
An internal PLL clock multiplier is included and generates the
necessary on-chip high frequency clocks. It can also be disabled
to allow the use of a higher performance external clock source.
An internal programmable divider simplifies clock generation
in the converter when using an external clock source. A flexible
data input interface allows for straight binary or twos complement
formats and supports single-port interleaved or dual-port data.
1
Protected by U.S. Patent Numbers 5,568,145; 5,689,257; and 5,703,519. Other
patents pending.
Dual high performance DAC outputs provide a differential
current output programmable over a 2 mA to 20 mA range. The
AD9773 is manufactured on an advanced 0.35 micron CMOS
process, operates from a single supply of 3.1 V to 3.5 V, and
consumes 1.2 W of power.
Targeted at a wide dynamic range, multicarrier, and multistandard systems, the superb baseband performance of the
AD9773 is ideal for wide band CDMA, multicarrier CDMA,
multicarrier TDMA, multicarrier GSM, and high performance
systems employing high order QAM modulation schemes. The
image rejection feature simplifies and can help to reduce the
number of signal band filters needed in a transmit signal chain.
The direct IF mode helps to eliminate a costly mixer stage for a
variety of communications systems.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Rev. D | Page 4 of 60
The AD9773 is the 12-bit member of the AD977x pin
compatible, high performance, programmable 2×/4×/8×
interpolating TxDAC+ family.
Direct IF transmission is possible for 70 MHz + IFs
through a novel digital mixing process.
fS/2, fS/4, and fS/8 digital quadrature modulation and user
selectable image rejection simplify/remove cascaded SAW
filter stages.
A 2×/4×/8× user selectable interpolating filter eases data
rate and output signal reconstruction filter requirements.
User selectable twos complement/straight binary
data coding.
User programmable channel gain control over 1 dB range
in 0.01 dB increments.
User programmable channel offset control ±10% over
the FSR.
Ultrahigh speed 400 MSPS DAC conversion rate.
Internal clock divider provides data rate clock for
easy interfacing.
Flexible clock input with single-ended or differential input,
CMOS, or 1 V p-p LO sine wave input capability.
Low power: Complete CMOS DAC operates on 1.2 W from a
3.1 V to 3.5 V single supply. The 20 mA full-scale current can
be reduced for lower power operation, and several sleep
functions reduce power during idle periods.
On-chip voltage reference: The AD9773 includes a 1.20 V
temperature compensated band gap voltage reference.
80-lead thin quad flat package, exposed pad (TQFP_EP).
AD9773
SPECIFICATIONS
DC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
DC Accuracy 1
Integral Nonlinearity
Differential Nonlinearity
Monotonicity
ANALOG OUTPUT (for IR and 2R Gain Setting Modes)
Offset Error
Gain Error (with Internal Reference)
Gain Matching
Full-Scale Output Current 2
Output Compliance Range
Output Resistance
Output Capacitance
Gain, Offset Cal DACs, Monotonicity Guaranteed
REFERENCE OUTPUT
Reference Voltage
Reference Output Current 3
REFERENCE INPUT
Input Compliance Range
Reference Input Resistance
Small Signal Bandwidth
TEMPERATURE COEFFICIENTS
Offset Drift
Gain Drift (With Internal Reference)
Reference Voltage Drift
POWER SUPPLY
AVDD
Voltage Range
Analog Supply Current (IAVDD) 4
IAVDD in Sleep Mode
CLKVDD
Voltage Range
Clock Supply Current (ICLKVDD)4
CLKVDD (PLL ON)
Clock Supply Current (ICLKVDD)
DVDD
Voltage Range
Digital Supply Current (IDVDD)4
Nominal Power Dissipation
PDIS 5
PDIS in PWDN
Power Supply Rejection Ratio—AVDD
OPERATING RANGE
Min
12
−1.5
−1
−0.02
−1.0
−1.0
2
−1.0
Typ
Max
±0.4
+1.5
LSB
±0.2
+1
LSB
Guaranteed over specified temperature range
±0.01
+0.02
+1.0
+1.0
20
+1.25
% of FSR
% of FSR
% of FSR
mA
V
kΩ
pF
1.26
V
nA
1.25
7
0.5
V
kΩ
MHz
0
50
±50
ppm of FSR/°C
ppm of FSR/°C
ppm/°C
±0.1
200
3
1.14
Unit
Bits
1.20
100
0.1
3.1
3.3
72.5
23.3
3.5
76
26
V
mA
mA
3.1
3.3
8.5
3.5
10.0
V
mA
23.5
3.1
−40
1
Measured at IOUTA driving a virtual ground.
Nominal full-scale current, IOUTFS, is 32× the IREF current.
3
Use an external amplifier to drive any external load.
4
100 MSPS fDAC with fOUT = 1 MHz, all supplies = 3.3 V, no interpolation, no modulation.
5
400 MSPS fDAC, fDATA = 50 MSPS, fS/2 modulation, PLL enabled.
2
Rev. D | Page 5 of 60
3.3
34
380
1.75
6.0
±0.4
mA
3.5
41
410
+85
V
mA
mW
W
mW
% of FSR/V
°C
AD9773
DYNAMIC SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, PLLVDD = 0 V, IOUTFS = 20 mA, interpolation = 2×, differential
transformer-coupled output, 50 Ω doubly terminated, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
Maximum DAC Output Update Rate (fDAC)
Output Settling Time (tST) (to 0.025%)
Output Rise Time (10% to 90%) 1
Output Fall Time (10% to 90%)1
Output Noise (IOUTFS = 20 mA)
AC LINEARITY—BASEBAND MODE
Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS)
fDATA = 100 MSPS, fOUT = 1 MHz
fDATA = 65 MSPS, fOUT = 1 MHz
fDATA = 65 MSPS, fOUT = 15 MHz
fDATA = 78 MSPS, fOUT = 1 MHz
fDATA = 78 MSPS, fOUT = 15 MHz
fDATA = 160 MSPS, fOUT = 1 MHz
fDATA = 160 MSPS, fOUT = 15 MHz
Spurious-Free Dynamic Range Within a 1 MHz Window
fOUT = 0 dBFS, fDATA = 100 MSPS, fOUT = 1 MHz
Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = −6 dBFS)
fDATA = 65 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 65 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
fDATA = 78 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 78 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
fDATA = 160 MSPS, fOUT1 = 10 MHz; fOUT2 = 11 MHz
fDATA = 160 MSPS, fOUT1 = 20 MHz; fOUT2 = 21 MHz
Total Harmonic Distortion (THD)
fDATA = 100 MSPS, fOUT = 1 MHz; 0 dBFS
Signal-to-Noise Ratio (SNR)
fDATA = 78 MSPS, fOUT = 5 MHz; 0 dBFS
fDATA = 160 MSPS, fOUT = 5 MHz; 0 dBFS
Adjacent Channel Power Ratio (ACPR)
WCDMA with 3.84 MHz BW, 5 MHz Channel Spacing
IF = Baseband, fDATA = 76.8 MSPS
IF = 19.2 MHz, fDATA = 76.8 MSPS
Four-Tone Intermodulation
21 MHz, 22 MHz, 23 MHz, and 24 MHz at −12 dBFS (fDATA = MSPS, Missing Center)
AC LINEARITY—IF MODE
Four-Tone Intermodulation at IF = 200 MHz
201 MHz, 202 MHz, 203 MHz, and 204 MHz at −12 dBFS (fDATA = 160 MSPS, fDAC = 320 MHz)
1
Measured single-ended into 50 Ω load.
Rev. D | Page 6 of 60
Min
Typ
400
Max
Unit
11
0.8
0.8
50
MSPS
ns
ns
ns
pA√Hz
70
84.5
83
79
83
77
75
77
dBc
dBc
dBc
dBc
dBc
dBc
dBc
72
92.6
dBc
80
75
80
75
80
75
dBc
dBc
dBc
dBc
dBc
dBc
−82.4
dB
70
69
dB
dB
69
69
dBc
dBc
73
dBFS
69
dBFS
−70
AD9773
DIGITAL SPECIFICATIONS
TMIN to TMAX, AVDD = 3.3 V, CLKVDD = 3.3 V, PLLVDD = 0 V, DVDD = 3.3 V, IOUTFS = 20 mA, unless otherwise noted.
Table 3.
Parameter
DIGITAL INPUTS
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Input Capacitance
CLOCK INPUTS
Input Voltage Range
Common-Mode Voltage
Differential Voltage
SERIAL CONTROL BUS
Maximum SCLK Frequency (fSLCK)
Minimum Clock Pulse Width High (tPWH)
Minimum Clock Pulse Width Low (tPWL)
Maximum Clock Rise/Fall Time
Minimum Data/Chip Select Setup Time (tDS)
Minimum Data Hold Time (tDH)
Maximum Data Valid Time (tDV)
RESET Pulse Width
Inputs (SDI, SDIO, SCLK, CSB)
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Input Capacitance
SDIO Output
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Min
Typ
2.1
3
0
−10
−10
Max
Unit
0.9
+10
+10
V
V
μA
μA
pF
5
0
0.75
0.5
1.5
1.5
3
2.25
15
30
30
1
25
0
30
1.5
2.1
3
0
−10
−10
0.9
+10
+10
5
DRVDD − 0.6
0.4
30
30
Rev. D | Page 7 of 60
50
50
V
V
V
MHz
ns
ns
ms
ns
ns
ns
ns
V
V
μA
μA
pF
V
V
mA
mA
AD9773
DIGITAL FILTER SPECIFICATIONS
20
Table 4. Half-Band Filter No. 1 (43 Coefficients)
0
ATTENUATION (dBFS)
–20
–40
–60
–80
–100
0.5
1.0
1.5
2.0
02857-002
0
2.0
02857-003
–120
8
02857-004
Coefficient
8
0
−29
0
67
0
−134
0
244
0
−414
0
673
0
−1079
0
1772
0
−3280
0
10,364
16,384
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 2. 2× Interpolating Filter Response
20
0
ATTENUATION (dBFS)
Tap
1, 43
2, 42
3, 41
4, 40
5, 39
6, 38
7, 37
8, 36
9, 35
10, 34
11, 33
12, 32
13, 31
14, 30
15, 29
16, 28
17, 27
18, 26
19, 25
20, 24
21, 23
22
–20
–40
–60
–80
–100
Table 5. Half-Band Filter No. 2 (19 Coefficients)
Coefficient
19
0
−120
0
438
0
−1288
0
5047
8192
–120
0
0.5
1.0
1.5
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 3. 4× Interpolating Filter Response
20
0
ATTENUATION (dBFS)
Tap
1, 19
2, 18
3, 17
4, 16
5, 15
6, 14
7, 13
8, 12
9, 11
10
–20
–40
–60
–80
Table 6. Half-Band Filter No. 3 (11 Coefficients)
Tap
1, 11
2, 10
3, 9
4, 8
5, 7
6
–100
Coefficient
7
0
−53
0
302
512
–120
0
2
4
6
fOUT (NORMALIZED TO INPUT DATA RATE)
Figure 4. 8× Interpolating Filter Response
Rev. D | Page 8 of 60
AD9773
ABSOLUTE MAXIMUM RATINGS
Table 7.
Parameter
AVDD, DVDD, CLKVDD
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
REFIO, FSADJ1/FSADJ2
IOUTA, IOUTB
P1B11 to P1B0, P2B11 to P2B0, RESET
DATACLK, PLL_LOCK
CLK+, CLK−
LPF
SPI_CSB, SPI_CLK, SPI_SDIO, SPI_SDO
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
With Respect To
AGND, DGND, CLKGND
AVDD, DVDD, CLKVDD
AGND, DGND, CLKGND
AGND
AGND
DGND
DGND
CLKGND
CLKGND
DGND
Min
−0.3
−4.0
−0.3
−0.3
−1.0
−0.3
−0.3
−0.3
−0.3
−0.3
−65
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum ratings for extended periods may affect
device reliability.
Max
+4.0
+4.0
+0.3
AVDD + 0.3
AVDD + 0.3
DVDD + 0.3
DVDD + 0.3
CLKVDD + 0.3
CLKVDD + 0.3
DVDD + 0.3
125
+150
300
Unit
V
V
V
V
V
V
V
V
V
V
°C
°C
°C
THERMAL CHARACTERISTICS
Thermal Resistance
80-lead thin quad flat package, exposed pad (TQFP_EP)
θJA = 23.5°C/W (with thermal pad soldered to PCB)
ESD CAUTION
Rev. D | Page 9 of 60
AD9773
AVDD
AGND
AVDD
AGND
AVDD
AGND
AGND
IOUTB2
IOUTA2
AGND
AGND
IOUTB1
IOUTA1
AGND
AGND
AVDD
AGND
AVDD
AGND
AVDD
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
CLKVDD
1
LPF
2
CLKVDD
60
FSADJ1
59
FSADJ2
3
58
REFIO
CLKGND
4
57
RESET
CLK+
5
56
SPI_CSB
CLK–
6
55
SPI_CLK
CLKGND
7
54
SPI_SDIO
DATACLK/PLL_LOCK
8
53
SPI_SDO
DGND
9
52
DGND
51
DVDD
P1B11 (MSB) 11
50
NC
P1B10 12
49
NC
P1B9 13
48
NC
P1B8 14
47
NC
P1B7 15
46
P2B0 (LSB)
P1B6 16
45
P2B1
DGND 17
44
DGND
DVDD 18
43
DVDD
P1B5 19
42
P2B2
P1B4 20
41
P2B3
PIN 1
AD9773
TxDAC+
TOP VIEW
(Not to Scale)
DVDD 10
Figure 5. Pin Configuration
Rev. D | Page 10 of 60
02857-005
P2B4
P2B5
P2B6
P2B7
DVDD
DGND
P2B8
P2B9
ONEPORTCLK/P2B10
IQSEL/P2B11 (MSB)
NC
NC
NC
NC
DVDD
DGND
P1B0 (LSB)
P1B1
P1B2
P1B3
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
AD9773
Table 8. Pin Function Descriptions
Pin No.
1, 3
2
4, 7
5
6
8
Mnemonic
CLKVDD
LPF
CLKGND
CLK+
CLK−
DATACLK/PLL_LOCK
9, 17, 25,
35, 44, 52
10, 18, 26,
36, 43, 51
11 to 16,
19 to 24,
27 to 30,
47 to 50
31
DGND
Description
Clock Supply Voltage.
PLL Loop Filter.
Clock Supply Common.
Differential Clock Input.
Differential Clock Input.
With the PLL enabled, this pin indicates the state of the PLL. A read of a Logic 1 indicates the
PLL is in the locked state. Logic 0 indicates the PLL has not achieved lock. This pin can also be
programmed to act as either an input or output (Address 02h, Bit 3) DATACLK signal running
at the input data rate.
Digital Common.
DVDD
Digital Supply Voltage.
P1B11 (MSB) to P1B0 (LSB)
Port 1 Data Inputs.
NC
No Connect.
IQSEL/P2B11 (MSB)
32
ONEPORTCLK/P2B10
33, 34, 37 to
42, 45, 46
53
P2B9 to P2B0 (LSB)
In one-port mode, IQSEL = 1 followed by a rising edge of the differential input clock latches
the data into the I channel input register. IQSEL = 0 latches the data into the Q channel input
register. In two-port mode, this pin becomes the Port 2 MSB.
With the PLL disabled and the AD9773 in one-port mode, this pin becomes a clock output
that runs at twice the input data rate of the I and Q channels. This allows the AD9773 to
accept and demux interleaved I and Q data to the I and Q input registers.
Port 2 Data Inputs.
SPI_SDO
54
SPI_SDIO
55
SPI_CLK
56
SPI_CSB
57
RESET
58
59
60
61, 63, 65,
76, 78, 80
62, 64, 66,
67, 70, 71,
74, 75, 77,
79
68, 69
72, 73
REFIO
FSADJ2
FSADJ1
AVDD
In the case where SDIO is an input, SDO acts as an output. When SDIO becomes an output,
SDO enters a high-Z state. This pin can also be used as an output for the data rate clock. For
more information, see the Two-Port Data Input Mode section.
Bidirectional Data Pin. Data direction is controlled by Bit 7 of Register Address 00h. The
default setting for this bit is 0, which sets SDIO as an input.
Data input to the SPI port is registered on the rising edge of SPI_CLK. Data output on the SPI
port is registered on the falling edge.
Chip Select/SPI Data Synchronization. On momentary logic high, resets SPI port logic and
initializes instruction cycle.
Logic 1 resets all of the SPI port registers, including Address 00h, to their default values. A
software reset can also be done by writing a Logic 1 to SPI Register 00h, Bit 5. However, the
software reset has no effect on the bits in Address 00h.
Reference Output, 1.2 V Nominal.
Full-Scale Current Adjust, Q Channel.
Full-Scale Current Adjust, I Channel.
Analog Supply Voltage.
AGND
Analog Common.
IOUTB2, IOUTA2
IOUTB1, IOUTA1
Differential DAC Current Outputs, Q Channel.
Differential DAC Current Outputs, I Channel.
Rev. D | Page 11 of 60
AD9773
TYPICAL PERFORMANCE CHARACTERISTICS
10
10
0
0
–10
–10
–20
–20
AMPLITUDE (dBm)
–30
–40
–50
–60
–30
–40
–50
–60
–70
–70
–80
–80
–90
130
FREQUENCY (MHz)
0
50
100
150
FREQUENCY (MHz)
Figure 6. Single-Tone Spectrum @ fDATA = 65 MSPS with fOUT = fDATA/3
Figure 9. Single-Tone Spectrum @ fDATA = 78 MSPS with fOUT = fDATA/3
90
90
85
85
0dBFS
0dBFS
80
80
75
SFDR (dBc)
–6dBFS
70
–12dBFS
65
75
–6dBFS
70
–12dBFS
65
60
60
55
55
50
0
10
20
30
FREQUENCY (MHz)
02857-007
50
0
10
20
30
02857-010
SFDR (dBc)
02857-009
65
02857-006
–90
0
30
02857-011
AMPLITUDE (dBm)
T = 25°C, AVDD = 3.3 V, CLKVDD = 3.3 V, DVDD = 3.3 V, IOUTFS = 20 mA, interpolation = 2×, differential transformer-coupled output,
50 Ω doubly terminated, unless otherwise noted.
FREQUENCY (MHz)
Figure 7. In-Band SFDR vs. fOUT @ fDATA = 65 MSPS
Figure 10. In-Band SFDR vs. fOUT @ fDATA = 78 MSPS
90
90
0dBFS
85
85
0dBFS
80
75
75
70
SFDR (dBc)
80
–12dBFS
65
–6dBFS
70
–12dBFS
65
60
60
55
55
50
50
0
10
20
FREQUENCY (MHz)
30
02857-008
SFDR (dBc)
–6dBFS
Figure 8. Out-of-Band SFDR vs. fOUT @ fDATA = 65 MSPS
0
10
20
FREQUENCY (MHz)
Figure 11. Out-of-Band SFDR vs. fOUT @ fDATA = 78 MSPS
Rev. D | Page 12 of 60
AD9773
90
10
–6dBFS
–3dBFS
0
85
–10
–30
IMD (dBc)
AMPLITUDE (dBm)
80
–20
–40
–50
75
0dBFS
70
65
–60
60
–70
55
–80
100
200
02857-012
0
300
FREQUENCY (MHz)
0
10
20
30
FREQUENCY (MHz)
02857-015
50
–90
Figure 15. Third-Order IMD Products vs. fOUT @ fDATA = 65 MSPS
Figure 12. Single-Tone Spectrum @ fDATA = 160 MSPS with fOUT = fDATA/3
90
90
85
85
–6dBFS
0dBFS
0dBFS
80
75
75
IMD (dBc)
70
–6dBFS
–3dBFS
70
65
65
60
60
55
55
10
20
30
40
50
FREQUENCY (MHz)
0
02857-013
0
10
20
Figure 13. In-Band SFDR vs. fOUT @ fDATA = 160 MSPS
Figure 16. Third-Order IMD Products vs. fOUT @ fDATA = 78 MSPS
90
90
85
85
80
80
–6dBFS
–3dBFS
–6dBFS
IMD (dBc)
75
0dBFS
70
75
0dBFS
70
65
65
60
60
–12dBFS
55
55
50
50
0
10
20
30
40
50
FREQUENCY (MHz)
02857-014
SFDR (dBc)
30
FREQUENCY (MHz)
02857-016
50
50
Figure 14. Out-of-Band SFDR vs. fOUT @ fDATA = 160 MSPS
0
20
40
60
FREQUENCY (MHz)
Figure 17. Third-Order IMD Products vs. fOUT @ fDATA = 160 MSPS
Rev. D | Page 13 of 60
02857-017
SFDR (dBc)
–12dBFS
80
AD9773
90
90
–3dBFS
8×
–6dBFS
85
85
4×
80
80
75
75
1×
70
2×
65
70
65
60
60
55
55
50
3.1
0
20
40
02857-018
50
60
FREQUENCY (MHz)
4×
3.3
3.4
3.5
AVDD (V)
Figure 21. Third-Order IMD Products vs. AVDD @ fOUT = 10 MHz,
fDAC = 320 MSPS, fDATA = 160 MSPS
Figure 18. Third-Order IMD Products vs. fOUT and Interpolation Rate,
1× fDATA = 160 MSPS, 2× fDATA = 160 MSPS, 4× fDATA = 80 MSPS,
8× fDATA = 50 MSPS
90
3.2
02857-021
SFDR (dBc)
IMD (dBc)
0dBFS
8×
90
85
85
80
PLL OFF
75
2×
1×
SNR (dB)
IMD (dBc)
80
70
65
75
70
PLL ON
65
60
60
55
–5
0
AOUT (dBFS)
50
0
50
100
150
INPUT DATA RATE (MSPS)
Figure 19. Third-Order IMD Products vs. AOUT and Interpolation Rate,
fDATA = 50 MSPS for All Cases, 1× fDAC = 50 MSPS, 2× fDAC = 100 MSPS,
4× fDAC = 200 MSPS, 8× fDAC = 400 MSPS
Figure 22. SNR vs. Data Rate for fOUT = 5 MHz
90
90
80
80
SFDR (dBc)
75
70
–6dBFS
65
70
65
55
55
3.3
3.4
AVDD (V)
3.5
Figure 20. SFDR vs. AVDD @ fOUT = 10 MHz,
fDAC = 320 MSPS, fDATA = 160 MSPS
78MSPS
160MSPS
60
3.2
fDATA = 65MSPS
75
60
02857-020
SFDR (dBc)
85
0dBFS
–12dBFS
50
–50
0
50
TEMPERATURE (°C)
Figure 23. SFDR vs. Temperature @ fOUT = fDATA/11
Rev. D | Page 14 of 60
100
02857-023
85
50
3.1
02857-022
–10
02857-019
55
50
–15
AD9773
0
0
–10
–20
–30
AMPLITUDE (dBm)
AMPLITUDE (dBm)
–20
–40
–50
–60
–70
–40
–60
–80
–80
–90
–100
100
FREQUENCY (MHz)
0
10
15
20
25
30
35
40
FREQUENCY (MHz)
Figure 27. Two-Tone IMD Performance, fDATA = 150 MSPS, Interpolation = 4×
Figure 24. Single-Tone Spurious Performance, fOUT = 10 MHz,
fDATA = 150 MSPS, No Interpolation
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBm)
–40
–50
–60
–40
–50
–60
–70
–70
–80
–80
–90
–90
–100
–100
10
20
30
40
FREQUENCY (MHz)
0
02857-025
0
50
100
150
200
250
FREQUENCY (MHz)
Figure 25. Two-Tone IMD Performance, fDATA = 150 MSPS, No Interpolation
02857-028
AMPLITUDE (dBm)
5
02857-027
50
02857-024
–100
0
Figure 28. Single-Tone Spurious Performance, fOUT = 10 MHz,
fDATA = 80 MSPS, Interpolation = 4×
0
–10
0
–30
–20
AMPLITUDE (dBm)
–40
–50
–60
–70
–80
–40
–60
–90
–80
–100
50
100
150
200
250
FREQUENCY (MHz)
–100
0
5
10
15
20
25
FREQUENCY (MHz)
Figure 26. Single-Tone Spurious Performance, fOUT = 10 MHz,
fDATA = 150 MSPS, Interpolation = 2×
Figure 29. Two-Tone IMD Performance, fOUT = 10 MHz, fDATA = 50 MSPS,
Interpolation = 8×
Rev. D | Page 15 of 60
02857-029
0
02857-026
AMPLITUDE (dBm)
–20
0
–10
–20
–20
–30
–30
AMPLITUDE (dBm)
0
–10
–40
–50
–60
–70
–40
–50
–60
–70
–90
–90
–100
–100
0
100
200
300
FREQUENCY (MHz)
0
20
40
60
FREQUENCY (MHz)
Figure 31. Eight-Tone IMD Performance, fDATA = 160 MSPS,
Interpolation = 8×
Figure 30. Single-Tone Spurious Performance, fOUT = 10 MHz,
fDATA = 50 MSPS, Interpolation = 8×
Rev. D | Page 16 of 60
02857-031
–80
–80
02857-030
AMPLITUDE (dBm)
AD9773
AD9773
TERMINOLOGY
Adjacent Channel Power Ratio (ACPR)
A ratio, in dBc, between the measured power within a channel
relative to its adjacent channel.
Complex Image Rejection
In a traditional two-part upconversion, two images are created
around the second IF frequency. These images are redundant
and have the effect of wasting transmitter power and system
bandwidth. By placing the real part of a second complex
modulator in series with the first complex modulator, either
the upper or lower frequency image near the second IF can be
rejected.
Complex Modulation
The process of passing the real and imaginary components of a
signal through a complex modulator (transfer function = ejωt =
cosωt + jsinωt) and realizing real and imaginary components
on the modulator output.
Differential Nonlinearity (DNL)
DNL is the measure of the variation in analog value, normalized
to full scale, associated with a 1 LSB change in digital input code.
Gain Error
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to 1 minus the output when all inputs are set to 0.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV-s.
Group Delay
Number of input clocks between an impulse applied at the
device input and the peak DAC output current. A half-band FIR
filter has constant group delay over its entire frequency range.
Impulse Response
Response of the device to an impulse applied to the input.
Interpolation Filter
If the digital inputs to the DAC are sampled at a multiple rate of
fDATA (interpolation rate), a digital filter can be constructed with
a sharp transition band near fDATA/2. Images that would typically
appear around fDAC (output data rate) can be greatly suppressed.
Linearity Error
Also called integral nonlinearity (INL), linearity error is defined
as the maximum deviation of the actual analog output from the
ideal output, determined by a straight line drawn from 0 to full
scale.
Offset Error
The deviation of the output current from the ideal of 0 is called
offset error. For IOUTA, 0 mA output is expected when the inputs
are all 0s. For IOUTB, 0 mA output is expected when all inputs are
set to 1.
Output Compliance Range
The range of allowable voltage at the output of a current output
DAC. Operation beyond the maximum compliance limits may
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Pass Band
Frequency band in which any input applied therein passes
unattenuated to the DAC output.
Power Supply Rejection
The maximum change in the full-scale output as the supplies
are varied from minimum to maximum specified voltages.
Settling Time
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.
Spurious-Free Dynamic Range
The difference, in dB, between the rms amplitude of the output
signal and the peak spurious signal over the specified bandwidth.
Stop-Band Rejection
The amount of attenuation of a frequency outside the pass band
applied to the DAC, relative to a full-scale signal applied at the
DAC input within the pass band.
Temperature Drift
It is specified as the maximum change from the ambient (25°C)
value to the value at either TMIN or TMAX. For offset and gain
drift, the drift is reported in ppm of full-scale range (FSR) per
°C. For reference drift, the drift is reported in ppm per °C.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured fundamental. It is
expressed as a percentage or in decibels (dB).
Monotonicity
A DAC is monotonic if the output either increases or remains
constant as the digital input increases.
Rev. D | Page 17 of 60
AD9773
MODE CONTROL (VIA SPI PORT)
Table 9. Mode Control via SPI Port 1
Address
00h
Bit 7
SDIO
Bidirectional
0 = Input
1 = I/O
Bit 6
LSB, MSB First
0 = MSB
1 = LSB
Bit 5
Software
Reset
on Logic 1
01h
Filter
Interpolation
Rate
(1×, 2×, 4×, 8×)
Filter
Interpolation
Rate
(1×, 2×, 4×, 8×)
Modulation
Mode
(None, fS/2,
fS/4, fS/8)
02h
0 = Signed
Input Data
1 = Unsigned
0 = Two-Port
Mode
1 = One-Port
Mode
DATACLK
Driver
Strength
03h
Data Rate 2
Output Clock
04h
0 = PLL OFF2
1 = PLL ON
05h
IDAC
Fine Gain
Adjustment
Bit 4
Sleep
Mode
Logic 1
Shuts
Down the
DAC
Output
Currents
Modulation
Mode
(None, fS/2,
fS/4, fS/8)
08h
09h
IDAC Offset
Adjustment
Bit 9
IDAC IOFFSET
Direction
0 = IOFFSET
on IOUTA
1 = IOFFSET
on IOUTB
QDAC
Fine Gain
Adjustment
Bit 2
1R/2R Mode
DAC Output
Current Set by
One or Two
External
Resistors
0 = 2R, 1 = 1R
Bit 1
PLL_LOCK
Indicator
Bit 0
0 = No Zero
Stuffing on
Interpolation
Filters, Logic 1
Enables Zero
Stuffing
1 = Real Mix
Mode
0 = Complex
Mix Mode
0 = e–jωt
1 = e+jωt
ONEPORTCLK
Invert
0 = No Invert
1 = Invert
IQSEL
Invert
0 = No
Invert
1 = Invert
PLL Divide
(Prescaler)
Ratio
PLL Charge
Pump
Control
DATACLK/
PLL_LOCK2
Select
0=
PLLLOCK
1=
DATACLK
Q First
0 = I First
1 = Q First
PLL Divide
(Prescaler)
Ratio
PLL Charge
Pump
Control
IDAC
Fine Gain
Adjustment
IDAC
Coarse
Gain
Adjustment
IDAC Offset
Adjustment
Bit 3
IDAC Offset
Adjustment
Bit 1
IDAC
Fine Gain
Adjustment
IDAC
Coarse
Gain
Adjustment
IDAC Offset
Adjustment
Bit 2
IDAC Offset
Adjustment
Bit 0
QDAC
Fine Gain
Adjustment
QDAC
Fine Gain
Adjustment
DATACLK
Invert
0 = No
Invert
1 = Invert
PLL Charge
Pump
Control
0 = Automatic
Charge Pump
Control
1=
Programmable
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Coarse Gain
Adjustment
IDAC
Fine Gain
Adjustment
IDAC
Coarse Gain
Adjustment
IDAC Offset
Adjustment
Bit 8
IDAC Offset
Adjustment
Bit 7
IDAC Offset
Adjustment
Bit 6
IDAC Offset
Adjustment
Bit 5
IDAC Offset
Adjustment
Bit 4
QDAC
Fine Gain
Adjustment
QDAC
Fine Gain
Adjustment
QDAC
Fine Gain
Adjustment
QDAC
Fine Gain
Adjustment
QDAC
Fine Gain
Adjustment
06h
07h
Bit 3
Power-Down
Mode Logic 1
Shuts Down
All Digital and
Analog
Functions
Rev. D | Page 18 of 60
AD9773
Address
0Ah
Bit 7
Bit 6
Bit 5
Bit 4
0Bh
QDAC
Offset
Adjustment
Bit 9
QDAC IOFFSET
Direction
0 = IOFFSET
on IOUTA
1 = IOFFSET
on IOUTB
QDAC
Offset
Adjustment
Bit 8
QDAC
Offset
Adjustment
Bit 7
QDAC
Offset
Adjustment
Bit 6
0Ch
0Dh
1
2
Bit 3
QDAC
Coarse Gain
Adjustment
QDAC
Offset
Adjustment
Bit 5
Bit 2
QDAC
Coarse Gain
Adjustment
QDAC
Offset
Adjustment
Bit 4
Bit 1
QDAC
Coarse Gain
Adjustment
QDAC
Offset
Adjustment
Bit 3
QDAC
Offset
Adjustment
Bit 1
Bit 0
QDAC
Coarse Gain
Adjustment
QDAC
Offset
Adjustment
Bit 2
QDAC
Offset
Adjustment
Bit 0
Version
Register
Version
Register
Version
Register
Version
Register
Default values are shown in bold.
See the Two-Port Data Input Mode section for more information.
Rev. D | Page 19 of 60
AD9773
Bit 3: Logic 1 enables zero stuffing mode for interpolation
filters.
REGISTER DESCRIPTION
Address 00h
Bit 7: Logic 0 (default) causes the SPI_SDIO pin to act as an
input during the data transfer (Phase 2) of the communications
cycle. When set to 1, SPI_SDIO can act as an input or output,
depending on Bit 7 of the instruction byte.
Bit 6: Logic 0 (default) determines the direction (LSB/MSB
first) of the communications and data transfer communications
cycles. Refer to the MSB/LSB Transfers section for more details.
Bit 5: Writing a 1 to this bit resets the registers to their default
values and restarts the chip. The RESET bit always reads back 0.
Register Address 00h bits are not cleared by this software reset.
However, a high level at the RESET pin forces all registers,
including those in Address 00h, to their default state.
Bit 4: Sleep Mode. A Logic 1 to this bit shuts down the DAC
output currents.
Bit 3: Power-Down Mode. Logic 1 shuts down all analog and
digital functions except for the SPI port.
Bit 2: 1R/2R Mode. The default (0) places the AD9773 in tworesistor mode. In this mode, the IREF currents for the I and Q
DAC references are set separately by the RSET resistors on
FSADJ1 and FSADJ2 (Pin 59 and Pin 60). In 2R mode,
assuming the coarse gain setting is full scale and the fine gain
setting is zero, IFULLSCALE1 = 32 × VREF/FSADJ1 and IFULLSCALE2 =
32 × VREF/FSADJ2. With this bit set to 1, the reference currents
for both I and Q DACs are controlled by a single resistor on
Pin 60. IFULLSCALE in one-resistor mode for both I and Q DACs is
half of what it would be in 2R mode, assuming all other
conditions (RSET, register settings) remain unchanged. The fullscale current of each DAC can still be set to 20 mA by choosing
a resistor of half the value of the RSET value used in 2R mode.
Bit 1: PLL_LOCK Indicator. When the PLL is enabled, reading
this bit gives the status of the PLL. A Logic 1 indicates the PLL
is locked. A Logic 0 indicates an unlocked state.
Address 01h
Bit 7 and Bit 6: This is the filter interpolation rate according to
Table 10.
Table 10.
00
01
10
11
1×
2×
4×
8×
Bit 5 and Bit 4: This is the modulation mode according to
Table 11.
Table 11.
00
01
10
11
Bit 2: Default (1) enables the real mix mode. The I and Q data
channels are individually modulated by fS/2, fS/4, or fS/8 after
the interpolation filters. However, no complex modulation is
done. In the complex mix mode (Logic 0), the digital modulators on the I and Q data channels are coupled to create a
digital complex modulator. When the AD9773 is applied in
conjunction with an external quadrature modulator, rejection
can be achieved of either the higher or lower frequency image
around the second IF frequency (that is, the LO of the analog
quadrature modulator external to the AD9773) according to the
bit value of Register 01h, Bit 1.
Bit 1: Logic 0 (default) causes the complex modulation to be of
the form e−jωt, resulting in the rejection of the higher frequency
image when the AD9773 is used with an external quadrature
modulator. A Logic 1 causes the modulation to be of the form
e+jωt, which causes rejection of the lower frequency image.
Bit 0: In two-port mode, a Logic 0 (default) causes Pin 8 to act
as a lock indicator for the internal PLL. A Logic 1 in this register
causes Pin 8 to act as a DATACLK. For more information, see
the Two-Port Data Input Mode section.
Address 02h
Bit 7: Logic 0 (default) causes data to be accepted on the inputs
as twos complement. Logic 1 causes data to be accepted as
straight binary.
Bit 6: Logic 0 (default) places the AD9773 in two-port mode. I
and Q data enters the AD9773 via Port 1 and Port 2,
respectively. A Logic 1 places the AD9773 in one-port mode in
which interleaved I and Q data is applied to Port 1. See Table 8
for detailed information on the DATACLK/PLL_LOCK, IQSEL,
and ONEPORTCLK modes.
Bit 5: DATACLK Driver Strength. With the internal PLL
disabled and this bit set to Logic 0, it is recommended that
DATACLK be buffered. When this bit is set to Logic 1,
DATACLK acts as a stronger driver capable of driving small
capacitive loads.
Bit 4: Logic 0 (default). A value of 1 inverts DATACLK at Pin 8.
Bit 2: Logic 0 (default). A value of 1 inverts ONEPORTCLK
at Pin 32.
Bit 1: The Logic 0 (default) causes IQSEL = 0 to direct input
data to the I channel, while IQSEL = 1 directs input data to the
Q channel.
Bit 0: The Logic 0 (default) defines IQ pairing as IQ, IQ, ...
while programming a Logic 1 causes the pair ordering to
be QI, QI, ....
none
fS/2
fS/4
fS/8
Rev. D | Page 20 of 60
AD9773
Address 03h
Address 05h, 09h
Bit 7: Allows the data rate clock (divided down from the DAC
clock) to be output at either the DATACLK pin (Pin 8) or at the
SPI_SDO pin (Pin 53). The default of 0 in this bit enables the
data rate clock at DATACLK, while a 1 in this bit causes the data
rate clock to be output at SPI_SDO. For more information, see
the Two-Port Data Input Mode section.
Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0: These bits
represent an 8-bit binary number (Bit 7 MSB) that defines the
fine gain adjustment of the I (05h) and Q (09h) DAC according
to Equation 1.
Bit 1 and Bit 0: Setting this divide ratio to a higher number
allows the VCO in the PLL to run at a high rate (for best performance), while the DAC input and output clocks run substantially
slower. The divider ratio is set according to Table 12.
Table 12.
00
01
10
11
Address 07h, 0Bh
Address 08h, 0Ch
Bit 1 and Bit 0: The 10 bits from these two address pairs (07h,
08h and 0Bh, 0Ch) represent a 10-bit binary number that
defines the offset adjustment of the I and Q DACs according to
Equation 1: (07h, 0Bh: Bit 7 MSB; 08h, 0Ch: Bit 0 LSB).
Address 04h
Bit 7: Logic 0 (default) disables the internal PLL. Logic 1
enables the PLL.
Address 08h, 0Ch
Bit 6: Logic 0 (default) sets the charge pump control to
automatic. In this mode, the charge pump bias current is
controlled by the divider ratio defined in Address 03h, Bits 1
and 0. Logic 1 allows the user to manually define the charge
pump bias current using Address 04h, Bits 2, 1, and 0. Adjusting
the charge pump bias current allows the user to optimize the
noise/settling performance of the PLL.
Table 13.
000
001
010
011
111
Bit 3, Bit 2, Bit 1, and Bit 0: These bits represent a 4-bit binary
number (Bit 3 MSB) that defines the coarse gain adjustment of
the I (06h) and Q (0Ah) DACs according to Equation 1.
Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0: These bits
are used in conjunction with Address 08h, Address 0Ch, Bits [1:0].
÷1
÷2
÷4
÷8
Bit 2, Bit 1, and Bit 0: With the charge pump control set to
manual, these bits define the charge pump bias current
according to Table 13.
Address 06h, 0Ah
Bit 7: This bit determines the direction of the offset of the I (08h)
and Q (0Ch) DACs. A Logic 0 applies a positive offset current to
IOUTA, while a Logic 1 applies a positive offset current to IOUTB.
The magnitude of the offset current is defined by the bits in
Addresses 07h, 0Bh, 08h, and 0Ch according to Equation 1.
Equation 1 shows IOUTA and IOUTB as a function of fine gain,
coarse gain, and offset adjustment when using 2R mode. In 1R
mode, the current IREF is created by a single FSADJ1 resistor
(Pin 60). This current is divided equally into each channel so
that a scaling factor of one-half must be added to these
equations for full-scale currents for both DACs and the offset.
50 μA
100 μA
200 μA
400 μA
800 μA
⎡⎛ 6 × I REF ⎞⎛ COARSE + 1 ⎞ ⎛ 3 × I REF ⎞⎛ FINE ⎞⎤ ⎡⎛ 1024 ⎞⎛ DATA ⎞⎤
I OUTA = ⎢⎜
⎟−⎜
⎟⎜
⎟⎜
⎟⎥ × ⎢⎜
⎟⎜ 12 ⎟⎥( A)
16
⎠ ⎝ 32 ⎠⎝ 256 ⎠⎦ ⎣⎝ 24 ⎠⎝ 2
⎠⎦
⎣⎝ 8 ⎠⎝
⎡⎛ 6 × I REF ⎞⎛ COARSE + 1 ⎞ ⎛ 3 × I REF ⎞⎛ FINE ⎞⎤ ⎡⎛ 1024 ⎞⎛ 212 − DATA − 1 ⎞⎤
⎟⎟⎥( A)
I OUTB = ⎢⎜
⎟−⎜
⎟⎜
⎟⎜
⎟⎥ × ⎢⎜
⎟⎜
16
212
⎠ ⎝ 32 ⎠⎝ 256 ⎠⎦ ⎣⎢⎝ 24 ⎠⎜⎝
⎣⎝ 8 ⎠⎝
⎠⎦⎥
⎛ OFFSET ⎞
I OFFSET = 4 × I REF ⎜
⎟( A)
⎝ 1024 ⎠
Rev. D | Page 21 of 60
(1)
AD9773
FUNCTIONAL DESCRIPTION
The AD9773 dual interpolating DAC consists of two data
channels that can be operated completely independently or
coupled to form a complex modulator in an image reject
transmit architecture. Each channel includes three FIR filters,
making the AD9773 capable of 2×, 4×, or 8× interpolation.
High speed input and output data rates can be achieved within
the limitations shown in Table 14.
Table 14.
SDO (PIN 53)
AD9773 SPI PORT
INTERFACE
02857-032
SDIO (PIN 54)
SPI_CLK (PIN 55)
CSB (PIN 56)
Figure 32. SPI Port Interface
SERIAL INTERFACE FOR REGISTER CONTROL
Interpolation Rate
(MSPS)
Input Data Rate
(MSPS)
DAC Sample Rate
(MSPS)
1×
2×
4×
8×
160
160
100
50
160
320
400
400
Both data channels contain a digital modulator capable of
mixing the data stream with an LO of fDAC/2, fDAC/4, or fDAC/8,
where fDAC is the output data rate of the DAC. A zero stuffing
feature is also included and can be used to improve pass-band
flatness for signals being attenuated by the SIN(x)/x characteristic of the DAC output. The speed of the AD9773, combined
with its digital modulation capability, enables direct IF
conversion architectures at 70 MHz and higher.
The digital modulators on the AD9773 can be coupled to form
a complex modulator. By using this feature with an external
analog quadrature modulator, such as Analog Devices’ AD8345,
an image rejection architecture can be enabled. To optimize the
image rejection capability, as well as LO feedthrough in this
architecture, the AD9773 offers programmable (via the SPI
port) gain and offset adjust for each DAC.
Also included on the AD9773 are a phase-locked loop (PLL)
clock multiplier and a 1.20 V band gap voltage reference. With
the PLL enabled, a clock applied to the CLK+/CLK− inputs is
frequency multiplied internally and generates all necessary
internal synchronization clocks. Each 12-bit DAC provides two
complementary current outputs whose full-scale currents can
be determined either from a single external resistor or independently from two separate resistors (see the 1R/2R Mode
section). The AD9773 features a low jitter, differential clock
input that provides excellent noise rejection while accepting a
sine or square wave input. Separate voltage supply inputs are
provided for each functional block to ensure optimum noise
and distortion performance.
Sleep and power-down modes can be used to turn off the DAC
output current (sleep) or the entire digital and analog sections
(power-down) of the chip. An SPI-compliant serial port is used
to program the many features of the AD9773. Note that in
power-down mode, the SPI port is the only section of the chip
still active.
The AD9773 serial port is a flexible, synchronous serial
communications port that allows an easy interface to many
industry-standard microcontrollers and microprocessors.
The serial I/O is compatible with most synchronous transfer
formats, including both the Motorola SPI and Intel® SSR
protocols. The interface allows read/write access to all registers
that configure the AD9773. Single- or multiple-byte transfers
are supported as well as MSB first or LSB first transfer formats.
The AD9773’s serial interface port can be configured as a single
pin I/O (SDIO) or two unidirectional pins for I/O (SDIO/SDO).
GENERAL OPERATION OF THE SERIAL INTERFACE
There are two phases to a communication cycle with the
AD9773. Phase 1 is the instruction cycle, which is the writing of
an instruction byte into the AD9773 coincident with the first
eight SCLK rising edges. The instruction byte provides the
AD9773 serial port controller with information regarding the
data transfer cycle, which is Phase 2 of the communication
cycle. The Phase 1 instruction byte defines whether the upcoming data transfer is read or write, the number of bytes in the
data transfer, and the starting register address for the first byte
of the data transfer. The first eight SCLK rising edges of each
communication cycle are used to write the instruction byte into
the AD9773.
A Logic 1 on the SPI_CSB pin, followed by a logic low, resets
the SPI port timing to the initial state of the instruction cycle.
This is true regardless of the present state of the internal
registers or the other signal levels present at the inputs to the
SPI port. If the SPI port is in the middle of an instruction cycle
or a data transfer cycle, none of the present data is written.
The remaining SCLK edges are for Phase 2 of the communication
cycle. Phase 2 is the actual data transfer between the AD9773 and
the system controller. Phase 2 of the communication cycle is a
transfer of one to four data bytes, as determined by the instruction
byte. Normally, using one multibyte transfer is the preferred
method. However, single byte data transfers are useful to reduce
CPU overhead when register access requires one byte only.
Registers change immediately upon writing to the last bit of each
transfer byte.
Rev. D | Page 22 of 60
AD9773
The SPI_SDO and SPI_SDIO pins go to a high impedance state
when this input is high. Chip select should stay low during the
entire communication cycle.
INSTRUCTION BYTE
The instruction byte contains the information shown in
Table 15.
SPI_SDIO (Pin 54)—Serial Data I/O
Table 15.
N1
0
0
1
1
N0
0
1
0
1
Data is always written into the AD9773 on this pin. However,
this pin can be used as a bidirectional data line. The configuration of this pin is controlled by Bit 7 of Register Address 00h.
The default is Logic 0, which configures the SDIO pin as
unidirectional.
Description
Transfer 1 Byte
Transfer 2 Bytes
Transfer 3 Bytes
Transfer 4 Bytes
SPI_SDO (Pin 53)—Serial Data Out
R/W
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. In the case where the
AD9773 operates in a single bidirectional I/O mode, this pin
does not output data and is set to a high impedance state.
Bit 7 of the instruction byte determines whether a read or a
write data transfer occurs after the instruction byte write.
Logic 1 indicates read operation. Logic 0 indicates a write
operation.
MSB/LSB TRANSFERS
N1, N0
Bits 6 and 5 of the instruction byte determine the number of
bytes to be transferred during the data transfer cycle. The bit
decodes are shown in the following table.
MSB
I7
R/W
I6
N1
I5
N0
I4
A4
I3
A3
I2
A2
I1
A1
LSB
I0
A0
A4, A3, A2, A1, and A0
Bits 4, 3, 2, 1, and 0 of the instruction byte determine which
register is accessed during the data transfer portion of the
communications cycle. For multibyte transfers, this address is
the starting byte address. The remaining register addresses are
generated by the AD9773.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
SPI_CLK (Pin 55)—Serial Clock
The serial clock pin is used to synchronize data to and from the
AD9773 and to run the internal state machines. The SPI_CLK
maximum frequency is 15 MHz. All data input to the AD9773
is registered on the rising edge of SPI_CLK. All data is driven
out of the AD9773 on the falling edge of SPI_CLK.
The AD9773 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by the first LSB bit in Register 0. The
default is MSB first.
When this bit is set active high, the AD9773 serial port is in LSB
first format. In LSB first mode, the instruction byte and data
bytes must be written from LSB to MSB. In LSB first mode, the
serial port internal byte address generator increments for each
byte of the multibyte communication cycle.
When this bit is set default low, the AD9773 serial port is
in MSB first format. In MSB first mode, the instruction byte
and data bytes must be written from MSB to LSB. In MSB
first mode, the serial port internal byte address generator
decrements for each byte of the multibyte communication cycle.
When incrementing from 1Fh, the address generator changes to
00h. When decrementing from 00h, the address generator
changes to 1Fh.
SPI_CSB (Pin 56)—Chip Select
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial
communications lines.
Rev. D | Page 23 of 60
AD9773
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
SDIO
I6(N)
R/W
I5(N)
I4
I3
I2
I1
I0
SDO
D7N
D6N
D20
D10
D00
D7N
D6N
D20
D10
D00
02857-033
SCLK
Figure 33. Serial Register Interface Timing MSB First
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CS
I0
I1
I2
I3
I4
I5(N)
I6(N)
R/W
SDO
D00
D10
D20
D6N
D7N
D00
D10
D20
D6N
D7N
Figure 34. Serial Register Interface Timing LSB First
tSCLK
tDS
CS
tPWH
tPWL
SCLK
SDIO
tDH
INSTRUCTION BIT 7
T6
INSTRUCTION BIT
02857-035
tDS
Figure 35. Timing Diagram for Register Write to AD9773
CS
SCLK
tDV
SDIO
DATA BIT N
DATA BIT N–1
SDO
Figure 36. Timing Diagram for Register Read from AD9773
Rev. D | Page 24 of 60
02857-036
SDIO
02857-034
SCLK
AD9773
NOTES ON SERIAL PORT OPERATION
GAIN
CONTROL
REGISTERS
FINE
GAIN
DAC
1.2VREF
IDAC
IOUTB1
REFIO
COARSE
GAIN
DAC
0.1μF
The same considerations apply to setting the reset bit in
Register Address 00h. All other registers are set to their default
values, but the software reset does not affect the bits in
Register Address 00h.
COARSE
GAIN
DAC
QDAC
IOUTA2
IOUTB2
FSADJ1
RSET2
02857-037
OFFSET
OFFSET
CONTROL
DAC
GAIN
REGISTERS
CONTROL
REGISTERS
FSADJ2
RSET1
Figure 37. DAC Outputs, Reference Current Scaling,
and Gain/Offset Adjust
It is recommended to use only single-byte transfers when changing
serial port configurations or initiating a software reset.
A write to Bit 1, Bit 2, and Bit 3 of Address 00h with the same
logic levels as for Bit 7, Bit 6, and Bit 5 (bit pattern: XY1001YX
binary) allows the user to reprogram a lost serial port configuration and to reset the registers to their default values. A
second write to Address 00h with reset bit low and serial port
configuration as previously specified (XY) reprograms the OSC
IN multiplier setting. A changed fSYSCLK frequency is stable after
a maximum of 200 fMCLK cycles (equals wake-up time).
AVDD
84μA
REFIO
7kΩ
02857-038
0.7V
DAC OPERATION
Figure 38. Internal Reference Equivalent Circuit
25
COARSE REFERENCE CURRENT (mA)
The dual 12-bit DAC output of the AD9773, along with the
reference circuitry, gain, and offset registers, is shown in Figure 37
and Figure 38. Note that an external reference can be used by
simply overdriving the internal reference with the external
reference. Referring to the transfer functions in Equation 1, a
reference current is set by the internal 1.2 V reference, the
external RSET resistor, and the values in the coarse gain register.
The fine gain DAC subtracts a small amount from this and the
result is input to IDAC and QDAC, where it is scaled by an
amount equal to 1024/24. Figure 39 and Figure 40 show the
scaling effect of the coarse and fine adjust DACs. IDAC and
QDAC are PMOS current source arrays, segmented in a 5-4-3
configuration. The five most significant bits control an array of
31 current sources. The next four bits consist of 15 current
sources whose values are all equal to 1/16 of an MSB current
source. The three LSBs are binary weighted fractions of the
middle bits’ current sources. All current sources are switched to
either IOUTA or IOUTB, depending on the input code.
IOUTA1
The fine adjustment of the gain of each channel allows for
improved balance of QAM modulated signals, resulting in
improved modulation accuracy and image rejection. In the
Interfacing the AD9773 with the AD8345 Quadrature
Modulator section, the performance data shows to what degree
image rejection can be improved when the AD9773 is used with
an AD8345 quadrature modulator from Analog Devices Inc.
Rev. D | Page 25 of 60
20
2R MODE
15
10
1R MODE
5
0
0
5
10
15
COARSE GAIN REGISTER CODE
(ASSUMING RSET 1, RSET 2 = 1.9kΩ)
Figure 39. Coarse Gain Effect on IFULLSCALE
20
02857-039
The AD9773 serial port configuration bits reside in Bits 6 and 7
of Register Address 00h. It is important to note that the configuration changes immediately upon writing to the last bit of the
register. For multibyte transfers, writing to this register can
occur during the middle of the communication cycle. Care
must be taken to compensate for this new configuration for the
remaining bytes of the current communication cycle.
OFFSET
CONTROL OFFSET
DAC
REGISTERS
FINE
GAIN
DAC
AD9773
5
–0.5
4
1R MODE
OFFSET CURRENT (mA)
–1.0
2R MODE
–1.5
–2.0
3
2R MODE
2
1R MODE
1
–2.5
–3.0
400
600
800
FINE GAIN REGISTER CODE
(ASSUMING RSET 1, RSET 2 = 1.9kΩ)
1000
0
200
02857-040
200
400
600
800
1000
COARSE GAIN REGISTER CODE
(ASSUMING RSET1, RSET2 = 1.9kΩ)
Figure 40. Fine Gain Effect on IFULLSCALE
02857-041
0
0
Figure 41. DAC Output Offset Current
In Figure 42, the negative scale represents an offset added to
IOUTB, while the positive scale represents an offset added to IOUTA
of the respective DAC. Offset Register 1 corresponds to IDAC,
while Offset Register 2 corresponds to QDAC. Figure 42
represents the AD9773 synthesizing a complex signal that is
then dc-coupled to an AD8345 quadrature modulator with an
LO of 800 MHz. The dc coupling allows the input offset of the
AD8345 to be calibrated out as well. The LO suppression at the
AD8345 output was optimized first by adjusting Offset Register 1
in the AD9773. When an optimal point was found (roughly
Code 54), this code was held in Offset Register 1, and Offset
Register 2 was adjusted. The resulting LO suppression is
70 dBFS. These are typical numbers, and the specific code for
optimization varies from part to part.
0
–10
OFFSET REGISTER 1 ADJUSTED
LO SUPPRESSION (dBFS)
The offset control defines a small current that can be added
to IOUTA or IOUTB (not both) on the IDAC and QDAC. The
selection in which IOUT for this offset current is directed toward
is programmable via Register 08h, Bit 7 (IDAC) and Register
0Ch, Bit 7 (QDAC). Figure 41 shows the scale of the offset
current that can be added to one of the complementary outputs
on the IDAC and QDAC. Offset control can be used for
suppression of LO leakage resulting from modulation of dc
signal components. If the AD9773 is dc-coupled to an external
modulator, this feature can be used to cancel the output offset
on the AD9773 as well as the input offset on the modulator.
Figure 42 shows a typical example of the effect that the offset
control has on LO suppression.
–20
–30
–40
–50
–60
OFFSET REGISTER 2
ADJUSTED, WITH OFFSET
REGISTER 1 SET
TO OPTIMIZED VALUE
–70
–80
–1024
–768
–512
–256
0
256
512
768
1024
DAC1, DAC2 (OFFSET REGISTER CODES)
02857-042
FINE REFERENCE CURRENT (mA)
0
Figure 42. Offset Adjust Control, Effect on LO Suppression
1R/2R MODE
In 2R mode, the reference current for each channel is set
independently by the FSADJ resistor on that channel. The
AD9773 can be programmed to derive its reference current
from a single resistor on Pin 60 by putting the part into 1R
mode. The transfer functions in Equation 1 are valid for 2R
mode. In 1R mode, the current developed in the single FSADJ
resistor is split equally between the two channels. The result is
that in 1R mode, a scale factor of 1/2 must be applied to the
formulas in Equation 1. The full-scale DAC current in 1R mode
can still be set to as high as 20 mA by using the internal 1.2 V
reference and a 950 Ω resistor instead of the 1.9 kΩ resistor
typically used in 2R mode.
Rev. D | Page 26 of 60
AD9773
CLOCK INPUT CONFIGURATIONS
The clock inputs to the AD9773 can be driven differentially or
single-ended. The internal clock circuitry has supply and
ground (CLKVDD, CLKGND) separate from the other supplies
on the chip to minimize jitter from internal noise sources.
Figure 43 shows the AD9773 driven from a single-ended clock
source. The CLK+/CLK− pins form a differential input
(CLKIN) so that the statically terminated input must be dcbiased to the midswing voltage level of the clock driven input.
AD9773
RSERIES
CLK+
CLKVDD
CLK–
VTHRESHOLD
0.1μF
Figure 43. Single-Ended Clock Driving Clock Inputs
A configuration for differentially driving the clock inputs is
given in Figure 44. DC-blocking capacitors can be used to
couple a clock driver output whose voltage swings exceed
CLKVDD or CLKGND. If the driver voltage swings are within
the supply range of the AD9773, the dc-blocking capacitors and
bias resistors are not necessary.
AD9773
0.1μF
1kΩ
CLK+
1kΩ
ECL/PECL
0.1μF
0.1μF
CLKVDD
1kΩ
CLK–
02857-044
1kΩ
CLKGND
The quality of the clock and data input signals is important in
achieving optimum performance. The external clock driver
circuitry should provide the AD9773 with a low jitter clock
input that meets the minimum/maximum logic levels while
providing fast edges. Although fast clock edges help minimize
any jitter that manifests itself as phase noise on a reconstructed
waveform, the high gain bandwidth product of the AD9773’s
clock input comparator can tolerate differential sine wave inputs
as low as 0.5 V p-p, with minimal degradation of the output
noise floor.
PROGRAMMABLE PLL
02857-043
CLKGND
These networks depend on the assumed transmission line
impedance and power supply voltage of the clock driver.
Optimum performance of the AD9773 is achieved when the
driver is placed very close to the AD9773 clock inputs, thereby
negating any transmission line effects such as reflections due to
mismatch.
Figure 44. Differential Clock Driving Clock Inputs
A transformer, such as the T1-1T from Mini-Circuits®, can also be
used to convert a single-ended clock to differential. This method is
used on the AD9773 evaluation board so that an external sine wave
with no dc offset can be used as a differential clock.
PECL/ECL drivers require varying termination networks, the
details of which are left out of Figure 43 and Figure 44 but can
be found in application notes such as the AND8020/D from On
Semiconductor®.
CLKIN can function either as an input data rate clock (PLL
enabled) or as a DAC data rate clock (PLL disabled) according
to the state of Address 02h, Bit 7 in the SPI port register. The
internal operation of the AD9773 clock circuitry in these two
modes is illustrated in Figure 45 and Figure 46.
The PLL clock multiplier and distribution circuitry produce the
necessary internal synchronized 1×, 2×, 4×, and 8× clocks for
the rising edge triggered latches, interpolation filters, modulators, and DACs. This circuitry consists of a phase detector,
charge pump, voltage controlled oscillator (VCO), prescaler,
clock distribution, and SPI port control. The charge pump,
VCO, differential clock input buffer, phase detector, prescaler,
and clock distribution are all powered from CLKVDD. PLL lock
status is indicated by the logic signal at the DATACLK_PLL_LOCK
pin, as well as by the status of Bit 1, Register 00h. To ensure
optimum phase noise performance from the PLL clock
multiplier and distribution, CLKVDD should originate from a
clean analog supply. The VCO speed is a function of the input
data rate, the interpolation rate, and the VCO prescaler,
according to the following function:
VCO Speed ( MHz ) =
Input Data Rate( MHz ) × Interpolation Rate × Prescaler
Table 16 defines the minimum input data rates vs. the
interpolation and PLL divider setting. If the input data rate
drops below the defined minimum rates under these
conditions, VCO phase noise may increase significantly.
Rev. D | Page 27 of 60
AD9773
CLK+
PLLVDD
PLL_LOCK
1 = LOCK
0 = NO LOCK
AD9773
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
2
4
However, maximum rates of less than 160 MSPS and all
minimum fDATA rates are due to the maximum and minimum
speeds of the internal PLL VCO. Figure 48 shows typical
performance of the PLL lock signal (Pin 8 or Pin 53) when the
PLL is in the process of locking.
CLK–
PHASE
DETECTOR
CHARGE
PUMP
Table 16. PLL Optimization
LPF
8
1
CLOCK
DISTRIBUTION
CIRCUITRY
INTERPOLATION
RATE
CONTROL
PRESCALER
VCO
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
REGISTERS
MODULATION
RATE
CONTROL
SPI PORT
PLL
CONTROL
(PLL ON)
02857-045
INPUT
DATA
LATCHES
Figure 45. PLL and Clock Circuitry with PLL Enabled
CLK+
CLK–
PLL_LOCK
1 = LOCK
0 = NO LOCK
INTERPOLATION
FILTERS,
MODULATORS,
AND DACS
2
4
AD9773
PHASE
DETECTOR
CHARGE
PUMP
PRESCALER
VCO
Maximum
fDATA
160
160
112
56
160
112
56
28
100
56
28
14
50
28
14
7
Minimum
fDATA
32
16
8
4
24
12
6
3
24
12
6
3
24
12
6
3
Table 17. Required PLL Prescaler Ratio vs. fDATA
PLL DIVIDER
(PRESCALER)
CONTROL
INTERNAL SPI
CONTROL
REGISTERS
SPI PORT
MODULATION
RATE
CONTROL
PLL
CONTROL
(PLL ON)
02857-046
CLOCK
DISTRIBUTION
CIRCUITRY
INTERPOLATION
RATE
CONTROL
Divider
Setting
1
2
4
8
1
2
4
8
1
2
4
8
1
2
4
8
8
1
INPUT
DATA
LATCHES
Interpolation
Rate
1
1
1
1
2
2
2
2
4
4
4
4
8
8
8
8
fDATA
125 MSPS
125 MSPS
100 MSPS
75 MSPS
50 MSPS
PLL
Disabled
Enabled
Enabled
Enabled
Enabled
Prescaler Ratio
Div 1
Div 2
Div 2
Div 4
Figure 46. PLL and Clock Circuitry with PLL Disabled
0
–10
–20
–30
PHASE NOISE (dBFS)
–40
–50
–60
–70
–80
–90
–100
–110
0
1
2
3
4
FREQUENCY OFFSET (MHz)
Figure 47. Phase Noise Performance
Rev. D | Page 28 of 60
5
02857-047
In addition, if the zero stuffing option is enabled, the VCO
doubles its speed again. Phase noise may be slightly higher with
the PLL enabled. Figure 47 illustrates typical phase noise
performance of the AD9773 with 2× interpolation and various
input data rates. The signal synthesized for the phase noise
measurement was a single carrier at a frequency of fDATA/4. The
repetitive nature of this signal eliminates quantization noise and
distortion spurs as a factor in the measurement. Although the
curves blend together in Figure 47, the different conditions are
given for clarity in Table 17. Table 16 details PLL divider
settings vs. interpolation rate and maximum and minimum
fDATA rates. Note that the maximum fDATA rates of 160 MSPS are
due to the maximum input data rate of the AD9773.
AD9773
76.0
4×, (MOD. ON)
8×, (MOD. ON)
75.5
2×, (MOD. ON)
IAVDD (mA)
75.0
74.5
4×
8×
74.0
73.5
2×
73.0
1×
02857-048
72.5
0
50
100
Figure 48. PLL_LOCK Output Signal (Pin 8) in the
Process of Locking (Typical Lock Time)
35
8×
30
4×
2×, (MOD. ON)
4×, (MOD. ON)
4×
2×
200
150
1×
0
100
150
50
100
150
200
fDATA (MHz)
Figure 51. ICLKVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
SLEEP/POWER-DOWN MODES
(Control Register 00h, Bit 3 and Bit 4)
200
fDATA (MHz)
Figure 49. IDVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
Rev. D | Page 29 of 60
02857-051
0
0
50
1×
5
50
0
15
10
02857-049
IDVDD (mA)
300
100
20
The AD9773 provides two methods for programmable
reduction in power savings. The sleep mode, when activated,
turns off the DAC output currents but the rest of the chip
remains functioning. When coming out of sleep mode, the
AD9773 immediately returns to full operation. Power-down
mode, on the other hand, turns off all analog and digital
circuitry in the AD9773 except for the SPI port. When
returning from power-down mode, enough clock cycles must
be allowed to flush the digital filters of random data acquired
during the power-down cycle.
400
350
ICLKVDD (mA)
The AD9773 has three voltage supplies: DVDD, AVDD, and
CLKVDD. Figure 49, Figure 50, and Figure 51 show the current
required from each of these supplies when each is set to the
3.3 V nominal specified for the AD9773. Power dissipation (PD)
can easily be extracted by multiplying the given curves by 3.3.
As Figure 49 shows, IDVDD is very dependent on the input data
rate, the interpolation rate, and the activation of the internal
digital modulator. IDVDD, however, is relatively insensitive to the
modulation rate by itself. In Figure 50, IAVDD shows the same
type of sensitivity to the data, the interpolation rate, and the
modulator function but to a much lesser degree (<10%). In
Figure 51, ICLKVDD varies over a wide range yet is responsible for
only a small percentage of the overall AD9773 supply current
requirements.
8×
2×
25
POWER DISSIPATION
8×, (MOD. ON)
200
Figure 50. IAVDD vs. fDATA vs. Interpolation Rate, PLL Disabled
It is important to note that the resistor/capacitor needed for the
PLL loop filter is internal on the AD9773. This suffices unless the
input data rate is below 10 MHz, in which case an external series
RC is required between the LPF and CLKVDD pins.
250
150
fDATA (MHz)
02857-050
72.0
AD9773
TWO-PORT DATA INPUT MODE
ONE-PORT/TWO-PORT INPUT MODES
The digital data input ports can be configured as two
independent ports or as a single (one-port mode) port. In the
two-port mode, data at the two input ports is latched into the
AD9773 on every rising edge of the data rate clock (DATACLK).
Also, in the two-port mode, the AD9773 can be programmed to
generate an externally available DATACLK for the purpose of
data synchronization. This data rate clock can be programmed to
be available at either Pin 8 (DATACLK/PLL_LOCK) or Pin 53
(SPI_SDO). Because Pin 8 can also function as a PLL lock
indicator when the PLL is enabled, there are several options for
configuring Pin 8 and Pin 53. The following information
describes the options.
The digital data input ports can be configured as two
independent ports or as a single (one-port mode) port. In twoport mode, the AD9773 can be programmed to generate an
externally available data rate clock (DATACLK) for the purpose
of data synchronization. Data at the two input ports can be
latched into the AD9773 on every rising clock edge of
DATACLK. In one-port mode, P2B10 and P2B11 from Input
Data Port 2 are redefined as IQSEL and ONEPORTCLK,
respectively. The input data in one-port mode is steered to one
of the two internal data channels based on the logic level of
IQSEL. A clock signal, ONEPORTCLK, is generated by the
AD9773 in this mode for the purpose of external data
synchronization. ONEPORTCLK runs at the input interleaved
data rate, which is 2× the data rate at the internal input to either
channel.
PLL Off (Register 4, Bit 7 = 0)
Register 4, Bit 7 = 0; DATACLK out of Pin 8.
Register 4, Bit 7 = 1; DATACLK out of Pin 53.
PLL On (Register 4, Bit 7 = 1)
Register 4, Bit 7 = 0, Register 1, Bit 0 = 0; PLL lock indicator out
of Pin 8.
Register 4, Bit 7 = 1, Register 1, Bit 0 = 0; PLL lock indicator out
of Pin 53.
Register4, Bit 7 = 0, Register 1, Bit 0 = 1; DATACLK out of Pin 8.
Register 4, Bit 7 = 1, Register 1, Bit 0 = 1; DATACLK out of Pin 53.
In one-port mode, P2B14 and P2B15 from input data port two
are redefined as IQSEL and ONEPORTCLK, respectively. The
input data in one-port mode is steered to one of the two internal
data channels based on the logic level of IQSEL. A clock signal,
ONEPORTCLK, is generated by the AD9773 in this mode for
the purpose of data synchronization. ONEPORTCLK runs at
the input interleaved data rate, which is 2× the data rate at the
internal input to either channel.
Test configurations showing the various clocks that are required
and generated by the AD9773 with the PLL enabled/disabled
and in the one-port/two-port modes are given in Figure 101 to
Figure 104. Jumper positions needed to operate the AD9773
evaluation board in these modes are given as well.
Test configurations showing the various clocks required and
produced by the AD9773 in the PLL and one-port/two-port
modes are given in Figure 101 to Figure 104. Jumper positions
needed to operate the AD9773 evaluation board in these modes
are given as well.
PLL ENABLED, TWO-PORT MODE
(Control Register 02h, Bits [6:0] and 04h, Bits [7:1]
With the phase-locked loop (PLL) enabled and the AD9773 in
two-port mode, the speed of CLKIN is inherently that of the
input data rate. In two-port mode, Pin 8 (DATACLK/PLL_
LOCK) can be programmed (Control Register 01h, Bit 0) to
function as either a lock indicator for the internal PLL or as a
clock running at the input data rate. When Pin 8 is used as a
clock output (DATACLK), its frequency is equal to that of
CLKIN. Data at the input ports is latched into the AD9773 on
the rising edge of the CLKIN. Figure 52 shows the delay, tOD,
inherent between the rising edge of CLKIN and the rising edge
of DATACLK, as well as the setup and hold requirements for
the data at Ports 1 and 2. The setup and hold times given in
Figure 52 are the input data transitions with respect to CLKIN.
Note that in two-port mode (PLL enabled or disabled), the data
rate at the interpolation filter inputs is the same as the input
data rate at Ports 1 and 2.
The DAC output sample rate in two-port mode is equal to the
clock input rate multiplied by the interpolation rate. If zero
stuffing is used, another factor of 2 must be included to
calculate the DAC sample rate.
Rev. D | Page 30 of 60
AD9773
DATACLK INVERSION
PLL ENABLED, ONE-PORT MODE
(Control Register 02h, Bit 4)
(Control Register 02h, Bits [6:1] and 04h, Bits [7:1]
By programming this bit, the DATACLK signal shown in
Figure 52 can be inverted. With inversion enabled, tOD refers to
the time between the rising edge of CLKIN and the falling edge
of DATACLK. No other effect on timing occurs.
In one-port mode, the I and Q channels receive their data from
an interleaved stream at Digital Input Port 1. The function of
Pin 32 is defined as an output (ONEPORTCLK) that generates a
clock at the interleaved data rate, which is 2× the internal input
data rate of the I and Q channels. The frequency of CLKIN is
equal to the internal input data rate of the I and Q channels.
The selection of the data for the I or Q channel is determined by
the state of the logic level at Pin 31 (IQSEL when the AD9773 is
in one-port mode) on the rising edge of ONEPORTCLK. Under
these conditions, IQSEL = 0 latches the data into the I channel
on the clock rising edge, while IQSEL = 1 latches the data into
the Q channel. It is possible to invert the I and Q selection by
setting Control Register 02h, Bit 1 to the invert state (Logic 1).
Figure 54 illustrates the timing requirements for the data inputs
as well as the IQSEL input. Note that the 1× interpolation rate is
not available in the one-port mode.
tOD
CLKIN
DATACLK
DATA AT PORTS
1 AND 2
tH
02857-052
tS
tS = 0.0ns (MAX)
tH = 2.5ns (MAX)
Figure 52. Timing Requirements in Two-Port
Input Mode with PLL Enabled
The DAC output sample rate in one port mode is equal to
CLKIN multiplied by the interpolation rate. If zero stuffing is
used, another factor of 2 must be included to calculate the DAC
sample rate.
ONEPORTCLK INVERSION
DATACLK DRIVER STRENGTH
(Control Register 02h, Bit 2)
(Control Register 02h, Bit 5)
By programming this bit, the ONEPORTCLK signal shown in
Figure 54 can be inverted. With inversion enabled, tOD refers to
the delay between the rising edge of the external clock and the
falling edge of ONEPORTCLK. The setup and hold times, tS
and tH, are with respect to the falling edge of ONEPORTCLK.
There is no other effect on timing.
The DATACLK output driver strength is capable of driving
>10 mA into a 330 Ω load while providing a rise time of 3 ns.
Figure 53 shows DATACLK driving a 330 Ω resistive load at a
frequency of 50 MHz. By enabling the drive strength option
(Control Register 02h, Bit 5), the amplitude of DATACLK under
these conditions increases by approximately 200 mV.
3.0
2.5
1.5
1.0
0.5
0
DELTA APPROX. 2.8ns
–0.5
0
10
20
30
40
50
TIME (ns)
02857-053
AMPLITUDE (V)
2.0
Figure 53. DATACLK Driver Capability into 330 Ω at 50 MHz
Rev. D | Page 31 of 60
AD9773
ONEPORTCLK DRIVER STRENGTH
PLL DISABLED, TWO-PORT MODE
The drive capability of ONEPORTCLK is identical to that of
DATACLK in the two-port mode. Refer to Figure 53 for
performance under load conditions.
With the PLL disabled, a clock at the DAC output rate must be
applied to CLKIN. Internal clock dividers in the AD9773
synthesize the DATACLK signal at Pin 8, which runs at the
input data rate and can be used to synchronize the input data.
Data is latched into input Ports 1 and 2 of the AD9773 on the
rising edge of DATACLK. DATACLK speed is defined as the
speed of CLKIN divided by the interpolation rate. With zero
stuffing enabled, this division increases by a factor of 2. Figure 55
illustrates the delay between the rising edge of CLKIN and the
rising edge of DATACLK, as well as tS and tH in this mode.
tOD
tOD = 4.0ns (MIN)
TO 5.5ns (MAX)
CLKIN
tS = 3.0ns (MAX)
tH = –0.5ns (MAX)
tIQS = 3.5ns (MAX)
tIQH = –1.5ns (MAX)
ONEPORTCLK
The programmable modes DATACLK inversion and DATACLK
driver strength described in the previous section (PLL Enabled,
Two-Port Mode) have identical functionality with the PLL
disabled.
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
The data rate clock created by dividing down the DAC clock in
this mode can be programmed (via Register 03h, Bit 7) to be
output from the SPI_SDO pin, rather than the DATACLK pin.
In some applications, this may improve complex image
rejection. When SPI_SDO is used as data rate clock out, tOD
increases by 1.6 ns.
tS tH
tIQS
02857-054
IQSEL
tIQH
tOD
Figure 54. Timing Requirements in One-Port
Input Mode with the PLL Enabled
CLKIN
IQ PAIRING
(Control Register 02h, Bit 0)
DATACLK
DATA AT PORTS
1 AND 2
Given the following interleaved data stream, where the data
indicates the value with respect to full scale:
I
0.5
Q
0.5
I
1
Q
1
I
0.5
Q
0.5
I
0
Q
0
I
0.5
tS
Q
0.5
With the control register set to 0 (I first), the data appears at the
internal channel inputs in the following order in time:
I Channel
Q Channel
0.5
0.5
1
1
0.5
0.5
0
0
0.5
0.5
With the control register set to 1 (Q first), the data appears at
the internal channel inputs in the following order in time:
I Channel
Q Channel
0.5
y
1
0.5
0.5
1
0
0.5
0.5
0
x
0.5
The values x and y represent the next I value and the previous
Q value in the series.
tH
tOD = 6.5ns (MIN) TO 8.0ns (MAX)
tS = 5.0ns (MAX)
tH = –3.2ns (MAX)
02857-055
In one-port mode, the interleaved data is latched into the
AD9773 internal I and Q channels in pairs. The order of how
the pairs are latched internally is defined by this control register.
The following is an example of the effect this has on incoming
interleaved data.
Figure 55. Timing Requirements in Two-Port
Input Mode with PLL Disabled
PLL DISABLED, ONE-PORT MODE
In one-port mode, data is received into the AD9773 as an
interleaved stream on Port 1. A clock signal (ONEPORTCLK),
running at the interleaved data rate, which is 2× the input data
rate of the internal I and Q channels, is available for data
synchronization at Pin 32.
With PLL disabled, a clock at the DAC output rate must be
applied to CLKIN. Internal dividers synthesize the ONEPORTCLK
signal at Pin 32. The selection of the data for the I or Q channel
is determined by the state of the logic level applied to Pin 31
(IQSEL when the AD9773 is in one-port mode) on the rising
edge of ONEPORTCLK.
Rev. D | Page 32 of 60
AD9773
One-port mode is very useful when interfacing with devices
such as the Analog Devices AD6622 or AD6623 transmit signal
processors, in which two digital data channels have been
interleaved (multiplexed).
AMPLITUDE MODULATION
Given two sine waves at the same frequency, but with a 90°
phase difference, a point of view in time can be taken such that
the waveform that leads in phase is cosinusoidal and the
waveform that lags is sinusoidal. Analysis of complex variables
states that the cosine waveform can be defined as having real
positive and negative frequency components, while the sine
waveform consists of imaginary positive and negative frequency
images. This is shown graphically in the frequency domain in
Figure 57.
e–jωt/2j
The programmable modes’ ONEPORTCLK inversion,
ONEPORTCLK driver strength and IQ pairing described in the
PLL Enabled, Two-Port Mode section have identical
functionality with the PLL disabled.
SINE
DC
e–jωt/2j
tOD
e–jωt/2
e–jωt/2
COSINE
CLKIN
DC
02857-057
Under these conditions, IQSEL = 0 latches the data into the I
channel on the clock rising edge, while IQSEL = 1 latches the
data into the Q channel. It is possible to invert the I and Q
selection by setting Control Register 02h, Bit 1 to the invert
state (Logic 1). Figure 56 illustrates the timing requirements for
the data inputs as well as the IQSEL input. Note that the
1× interpolation rate is not available in the one-port mode.
Figure 57. Real and Imaginary Components of
Sinusoidal and Cosinusoidal Waveforms
Amplitude modulating a baseband signal with a sine or a cosine
convolves the baseband signal with the modulating carrier in
the frequency domain. Amplitude scaling of the modulated
signal reduces the positive and negative frequency images by a
factor of 2. This scaling is very important in the discussion of
the various modulation modes. The phase relationship of the
modulated signals is dependent on whether the modulating
carrier is sinusoidal or cosinusoidal, again with respect to the
reference point of the viewer. Examples of sine and cosine
modulation are given in Figure 58.
ONEPORTCLK
I AND Q INTERLEAVED
INPUT DATA AT PORT 1
tS tH
IQSEL
Ae–jωt/2j
tOD = 4.0ns (MIN)
tIQH
SINUSOIDAL
MODULATION
Figure 56. Timing Requirements in One-Port
Input Mode with DLL Disabled
DC
Ae–jωt/2j
Ae–jωt/2
DIGITAL FILTER MODES
The I and Q data paths of the AD9773 have their own
independent half-band FIR filters. Each data path consists of
three FIR filters, providing up to 8× interpolation for each
channel. The rate of interpolation is determined by the state of
Control Register 01h, Bits 7 and 6. Figure 2 to Figure 4 show the
response of the digital filters when the AD9773 is set to 2×, 4×,
and 8× modes. The frequency axes of these graphs have been
normalized to the input data rate of the DAC. As the graphs
show, the digital filters can provide greater than 75 dB of
out-of-band rejection.
An online tool is available for quick and easy analysis of the
AD9773 interpolation filters in the various modes.
Rev. D | Page 33 of 60
Ae–jωt/2
COSINUSOIDAL
MODULATION
DC
Figure 58. Baseband Signal, Amplitude Modulated
with Sine and Cosine Carriers
02857-058
tIQS
02857-056
TO 5.5ns (MAX)
tS = 3.0ns (MAX)
tH = –1.0ns (MAX)
tIQS = 3.5ns (MAX)
tIQH = –1.5ns (MAX)
AD9773
MODULATION, NO INTERPOLATION
With Control Register 01h, Bit 7 and Bit 6 set to 00, the
interpolation function on the AD9773 is disabled. Figure 59 to
Figure 62 show the DAC output spectral characteristics of the
AD9773 in the various modulation modes, all with the
interpolation filters disabled. The modulation frequency is
determined by the state of Control Register 01h, Bits 5 and 4.
The tall rectangles represent the digital domain spectrum of a
baseband signal of narrow bandwidth.
By comparing the digital domain spectrum to the DAC SIN(x)/x
roll-off, an estimate can be made for the characteristics required
for the DAC reconstruction filter. Note also, per the previous
discussion on amplitude modulation, that the spectral components (where modulation is set to fS/4 or fS/8) are scaled by a
factor of 2. In the situation where the modulation is fS/2, the
modulated spectral components add constructively, and there is
no scaling effect.
0
0
–20
–20
AMPLITUDE (dBFS)
–40
–60
–40
–60
–80
–80
0.2
0.4
0.6
0.8
1.0
fOUT (×fDATA)
02857-059
0
0
0.4
0.6
0.8
1.0
1.0
fOUT (×fDATA)
Figure 59. No Interpolation, Modulation Disabled
Figure 61. No Interpolation, Modulation = fDAC/4
0
–20
–20
AMPLITUDE (dBFS)
0
–40
–60
–40
–60
–80
–80
–100
–100
0
0.2
0.4
0.6
0.8
fOUT (×fDATA)
1.0
02857-060
AMPLITUDE (dBFS)
0.2
02857-061
–100
–100
02857-062
AMPLITUDE (dBFS)
The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation Disabled
Figure 60. No Interpolation, Modulation = fDAC/2
0
0.2
0.4
0.6
0.8
fOUT (×fDATA)
Figure 62. No Interpolation, Modulation = fDAC/8
Rev. D | Page 34 of 60
AD9773
MODULATION, INTERPOLATION = 2×
With Control Register 01h, Bit 7 and Bit 6 set to 01, the interpolation rate of the AD9773 is 2×. Modulation is achieved by
multiplying successive samples at the interpolation filter output
by the sequence (+1, −1). Figure 63 to Figure 66 represent
the spectral response of the AD9773 DAC output with 2×
interpolation in the various modulation modes to a narrow
band baseband signal (again, the tall rectangles in the graphic).
The advantage of interpolation becomes clear in Figure 63 to
Figure 66, where it can be seen that the images that would
normally appear in the spectrum around the input data rate
frequency are suppressed by >70 dB.
Another significant point is that the interpolation filtering is
done previous to the digital modulator. For this reason, as
Figure 63 to Figure 66 show, the pass band of the interpolation
filters can be frequency shifted, giving the equivalent of a highpass digital filter.
Note that when using the fS/4 modulation mode, there is no
true stop band as the band edges coincide with each other. In
the fS/8 modulation mode, amplitude scaling occurs over only
a portion of the digital filter pass band due to constructive
addition over just that section of the band.
0
0
–20
–20
AMPLITUDE (dBFS)
–40
–60
–40
–60
–80
–80
0.5
1.0
1.5
2.0
fOUT (×fDATA)
0
1.0
1.5
2.0
2.0
fOUT (×fDATA)
Figure 63. 2x Interpolation, Modulation = Disabled
Figure 65. 2x Interpolation, Modulation = fDAC/4
0
–20
–20
AMPLITUDE (dBFS)
0
–40
–60
–40
–60
–80
–80
–100
0
0.5
1.0
1.5
fOUT (×fDATA)
2.0
02857-064
AMPLITUDE (dBFS)
0.5
02857-065
–100
0
02857-063
–100
02857-066
AMPLITUDE (dBFS)
The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 2×
–100
Figure 64. 2x Interpolation, Modulation = fDAC/2
0
0.5
1.0
1.5
fOUT (×fDATA)
Figure 66. 2x Interpolation, Modulation = fDAC/8
Rev. D | Page 35 of 60
AD9773
MODULATION, INTERPOLATION = 4×
With Control Register 01h, Bit 7 and Bit 6 set to 10, the interpolation rate of the AD9773 is 4×. Modulation is achieved by
multiplying successive samples at the interpolation filter output
by the sequence (0, +1, 0, −1).
Figure 67 to Figure 70 represent the spectral response of the
AD9773 DAC output with 4× interpolation in the various
modulation modes to a narrow band baseband signal.
0
0
–20
–20
AMPLITUDE (dBFS)
–40
–60
–40
–60
–80
–80
1
2
3
4
fOUT (×fDATA)
0
2
3
4
4
fOUT (×fDATA)
Figure 67. 4x Interpolation, Modulation Disabled
Figure 69. 4x Interpolation, Modulation = fDAC/4
0
0
–20
AMPLITUDE (dBFS)
–20
–40
–60
–40
–60
–80
–80
–100
0
1
2
3
fOUT (×fDATA)
4
02857-068
AMPLITUDE (dBFS)
1
02857-069
–100
0
02857-067
–100
02857-070
AMPLITUDE (dBFS)
The Effects of the Digital Modulation on the DAC Output Spectrum Interpolation = 4×
–100
Figure 68. 4x Interpolation, Modulation = fDAC/2
0
1
2
3
fOUT (×fDATA)
Figure 70. 4x Interpolation, Modulation = fDAC/8
Rev. D | Page 36 of 60
AD9773
MODULATION, INTERPOLATION = 8×
With Control Register 01h, Bit 7 and Bit 6 set to 11, the
interpolation rate of the AD9773 is 8×. Modulation is achieved
by multiplying successive samples at the interpolation filter
output by the sequence (0, +0.707, +1, +0.707, 0, −0.707, −1,
+0.707). Figure 71 to Figure 74 represent the spectral response
of the AD9773 DAC output with 8× interpolation in the various
modulation modes to a narrow band baseband signal.
Looking at Figure 63 to Figure 74, the user can see how higher
interpolation rates reduce the complexity of the reconstruction
filter needed at the DAC output. It also becomes apparent that
the ability to modulate by fS/2, fS/4, or fS/8 adds a degree of
flexibility in frequency planning.
0
0
–20
–20
AMPLITUDE (dBFS)
–40
–60
–40
–60
–80
–80
1
2
3
4
fOUT (×fDATA)
02857-071
0
0
2
3
4
5
6
7
8
8
fOUT (×fDATA)
Figure 71. 8x Interpolation, Modulation Disabled
Figure 73. 8x Interpolation, Modulation = fDAC/4
0
0
–20
AMPLITUDE (dBFS)
–20
–40
–60
–40
–60
–80
–80
–100
0
1
2
3
fOUT (×fDATA)
4
02857-072
AMPLITUDE (dBFS)
1
02857-073
–100
–100
02857-074
AMPLITUDE (dBFS)
The Effects of the Digital Modulation on the DAC Output Spectrum, Interpolation = 8×
–100
Figure 72. 8x Interpolation, Modulation = fDAC/2
0
1
2
3
4
5
6
7
fOUT (×fDATA)
Figure 74. 8x Interpolation, Modulation = fDAC/8
Rev. D | Page 37 of 60
AD9773
ZERO STUFFING
(Control Register 01h, Bit 3)
As shown in Figure 75, a 0 or null in the output frequency
response of the DAC (after interpolation, modulation, and DAC
reconstruction) occurs at the final DAC sample rate (fDAC). This
is due to the inherent SIN(x)/x roll-off response in the digitalto-analog conversion. In applications where the desired
frequency content is below fDAC/2, this may not be a problem.
Note that at fDAC/2, the loss due to SIN(x)/x is 4 dB. In direct RF
applications, this roll-off may be problematic due to the
increased pass-band amplitude variation as well as the reduced
amplitude of the desired signal.
Consider an application where the digital data into the AD9773
represents a baseband signal around fDAC/4 with a pass band of
fDAC/10. The reconstructed signal out of the AD9773 would
experience only a 0.75 dB amplitude variation over its pass
band. However, the image of the same signal occurring at
3 × fDAC/4 suffers from a pass-band flatness variation of 3.93 dB.
This image may be the desired signal in an IF application using
one of the various modulation modes in the AD9773. This rolloff of image frequencies can be seen in Figure 59 to Figure 74,
where the effect of the interpolation and modulation rate is
apparent as well.
10
It is important to realize that the zero stuffing option by itself
does not change the location of the images but rather their
amplitude, pass-band flatness, and relative weighting. For
instance, in the previous example, the pass-band amplitude
flatness of the image at 3 × fDATA/4 is now improved to 0.59 dB
while the signal level has increased slightly from −10.5 dBFS to
−8.1 dBFS.
INTERPOLATING (COMPLEX MIX MODE)
(Control Register 01h, Bit 2)
In the complex mix mode, the two digital modulators on the
AD9773 are coupled to provide a complex modulation function.
In conjunction with an external quadrature modulator, this
complex modulation can be used to realize a transmit image
rejection architecture. The complex modulation function can
be programmed for e+jωt or e−jωt to give upper or lower image
rejection. As in the real modulation mode, the modulation
frequency ω can be programmed via the SPI port for fDAC/2,
fDAC/4, and fDAC/8, where fDAC represents the DAC output rate.
OPERATIONS ON COMPLEX SIGNALS
Truly complex signals cannot be realized outside of a computer
simulation. However, two data channels, both consisting of real
data, can be defined as the real and imaginary components of a
complex signal. I (real) and Q (imaginary) data paths are often
defined this way. By using the architecture defined in Figure 76,
a system can be realized that operates on complex signals,
giving a complex (real and imaginary) output.
ZERO STUFFING
ENABLED
0
SIN (X)/X ROLL-OFF (dBFS)
The net effect is to increase the DAC output sample rate by a
factor of 2× with the 0 in the SIN(x)/x DAC transfer function
occurring at twice the original frequency. A 6 dB loss in
amplitude at low frequencies is also evident, as can be seen in
Figure 76.
–10
–20
ZERO STUFFING
DISABLED
–30
–40
0
0.5
1.0
1.5
2.0
fOUT, NORMALIZED TO fDATA WITH ZERO STUFFING DISABLED (Hz)
02857-075
–50
If a complex modulation function (e+jωt) is desired, the real and
imaginary components of the system correspond to the real and
imaginary components of e+jωt or cosωt and sinωt. As Figure 77
shows, the complex modulation function can be realized by
applying these components to the structure of the complex
system defined in Figure 76.
Figure 75. Effect of Zero Stuffing on DAC’s SIN(x)/x Response
Rev. D | Page 38 of 60
a(t)
INPUT
OUTPUT
c(t) × b(t) + d × b(t)
COMPLEX FILTER
= (c + jd)
b(t)
IMAGINARY
INPUT
OUTPUT
b(t) × a(t) + c × b(t)
Figure 76. Realization of a Complex System
02857-076
To improve upon the pass-band flatness of the desired image,
the zero stuffing mode can be enabled by setting the control
register bit to Logic 1. This option increases the ratio of
fDAC/fDATA by a factor of 2 by doubling the DAC sample rate and
inserting a midscale sample (that is, 1000 0000 0000 0000) after
every data sample originating from the interpolation filter. This
is important as it affects the PLL divider ratio needed to keep
the VCO within its optimum speed range. Note that the zero
stuffing takes place in the digital signal chain at the output of
the digital modulator, before the DAC.
AD9773
INPUT
(REAL)
OUTPUT
(REAL)
INPUT
(IMAGINARY)
OUTPUT
INPUT
(IMAGINARY)
SINωt
90°
90°
COSωt
02857-078
INPUT
(REAL)
Figure 78. Quadrature Modulator
e–jωt = COSωt + jSINωt
02857-077
OUTPUT
(IMAGINARY)
Figure 77. Implementation of a Complex Modulator
COMPLEX MODULATION AND IMAGE REJECTION
OF BASEBAND SIGNALS
In traditional transmit applications, a two-step upconversion is
done in which a baseband signal is modulated by one carrier to
an intermediate frequency (IF) and then modulated a second
time to the transmit frequency. Although this approach has
several benefits, a major drawback is that two images are
created near the transmit frequency. Only one image is needed,
the other being an exact duplicate. Unless the unwanted image
is filtered, typically with analog components, transmit power is
wasted and the usable bandwidth available in the system is
reduced.
The entire upconversion from baseband to transmit frequency is
represented graphically in Figure 79. The resulting spectrum
shown in Figure 79 represents the complex data consisting of the
baseband real and imaginary channels, now modulated onto
orthogonal (cosine and negative sine) carriers at the transmit
frequency. It is important to remember that in this application (two
baseband data channels) the image rejection is not dependent on
the data at either of the AD9773 input channels. In fact, image
rejection still occurs with either one or both of the AD9773 input
channels active. Note that by changing the sign of the sinusoidal
multiplying term in the complex modulator, the upper sideband
image could be suppressed while passing the lower one. This is
easily done in the AD9773 by selecting the e+jωt bit (Register 01h, Bit
1). In purely complex terms, Figure 79 represents the two-stage
upconversion from complex baseband to carrier.
A more efficient method of suppressing the unwanted image
can be achieved by using a complex modulator followed by a
quadrature modulator. Figure 78 is a block diagram of a
quadrature modulator. Note that it is in fact the real output
half of a complex modulator. The complete upconversion can
actually be referred to as two complex upconversion stages,
the real output of which becomes the transmitted signal.
Rev. D | Page 39 of 60
AD9773
REAL CHANNEL (OUT)
A/2
A/2
–fC1
fC
–B/2J
B/2J
– fC
fC
REAL CHANNEL (IN)
A
DC
COMPLEX
MODULATOR
TO QUADRATURE
MODULATOR
IMAGINARY CHANNEL (OUT)
–A/2J
A/2J
– fC
–fC
IMAGINARY CHANNEL (IN)
B
DC
B/2
B/2
– fC
fC
A/4 + B/4J
A/4 – B/4J
A/4 + B/4J
–fQ2
–fQ – fC
A/4 – B/4J
fQ
–fQ + fC
fQ – fC
fQ + fC
OUT
REAL
–A/4 – B/4J A/4 – B/4J
A/4 + B/4J –A/4 + B/4J
QUADRATURE
MODULATOR
–fQ
IMAGINARY
fQ
REJECTED IMAGES
–fQ
1f
C = COMPLEX MODULATION FREQUENCY
2f
Q = QUADRATURE MODULATION FREQUENCY
A/2 – B/2J
fQ
Figure 79. Two-Stage Upconversion and Resulting Image Rejection
Rev. D | Page 40 of 60
02857-079
A/2 + B/2J
AD9773
A system in which multiple baseband signals are complex
modulated and then applied to the AD9773 real and imaginary
inputs followed by a quadrature modulator is shown in
Figure 82, which also describes the transfer function of this
system and the spectral output. Note the similarity of the
transfer functions given in Figure 82 and Figure 80. Figure 82
adds an additional complex modulator stage for the purpose of
summing multiple carriers at the AD9773 inputs. Also, as in
Figure 79, the image rejection is not dependent on the real or
imaginary baseband data on any channel. Image rejection on a
channel occurs if either the real or imaginary data, or both, is
present on the baseband channel.
COMPLEX BASEBAND
SIGNAL
1
×
ej(ω1 + ω2)t
1/2
–ω1 – ω2
DC
ω1 + ω2
FREQUENCY
Figure 80. Two-Stage Complex Upconversion
IMAGE REJECTION AND SIDEBAND SUPPRESSION
OF MODULATED CARRIERS
As shown in Figure 79, image rejection can be achieved by
applying baseband data to the AD9773 and following the
AD9773 with a quadrature modulator. To process multiple
carriers while still maintaining image reject capability, each
carrier must be complex modulated. As Figure 81 shows, single
or multiple complex modulators can be used to synthesize
complex carriers. These complex carriers are then summed and
applied to the real and imaginary inputs of the AD9773.
R(1)
COMPLEX
MODULATOR 1
BASEBAND CHANNEL 2
REAL INPUT
R(2)
COMPLEX
MODULATOR 2
IMAGINARY INPUT
BASEBAND CHANNEL N
REAL INPUT
MULTICARRIER
REAL OUTPUT =
R(1) + R(2) + . . .R(N)
(TO REAL INPUT OF AD9773)
R(1)
IMAGINARY INPUT
MULTICARRIER
IMAGINARY OUTPUT =
I(1) + I(2) + . . .I(N)
(TO IMAGINARY INPUT OF AD9773)
R(2)
R(N)
COMPLEX
MODULATOR N
R(N) = REAL OUTPUT OF N
I(N) = IMAGINARY OUTPUT OF N
02857-081
BASEBAND CHANNEL 1
REAL INPUT
It is important to remember that the magnitude of a complex
signal can be 1.414× the magnitude of its real or imaginary
components. Due to this 3 dB increase in signal amplitude, the
real and imaginary inputs to the AD9773 must be kept at least
3 dB below full scale when operating with the complex
modulator. Overranging in the complex modulator results in
severe distortion at the DAC output.
R(N)
IMAGINARY INPUT
Figure 81. Synthesis of Multicarrier Complex Signal
MULTIPLE
BASEBAND
CHANNELS
REAL
IMAGINARY
MULTIPLE
COMPLEX
MODULATORS
FREQUENCY = ω1, ω2...ωN
REAL
AD9773
COMPLEX
MODULATOR
FREQUENCY = ωC
IMAGINARY
REAL
IMAGINARY
REAL
QUADRATURE
MODULATOR
FREQUENCY = ωQ
COMPLEX BASEBAND
SIGNAL
×
OUTPUT = REAL
–ω1 – ωC – ωQ
ej(ωN + ωC + ωQ)t
ω1 + ωC + ωQ
DC
REJECTED IMAGES
Figure 82. Image Rejection with Multicarrier Signals
Rev. D | Page 41 of 60
02857-082
= REAL
1/2
02857-080
OUTPUT = REAL
AD9773
The complex carrier synthesized in the AD9773 digital modulator is accomplished by creating two real digital carriers in
quadrature. Carriers in quadrature cannot be created with the
modulator running at fDAC/2. As a result, complex modulation
only functions with modulation rates of fDAC/4 and fDAC/8.
Regions A and B of Figure 83 to Figure 88 are the result of the
complex signal described previously, when complex modulated
in the AD9773 by +ejωt. Regions C and D are the result of the
complex signal described previously, again with positive frequency components only, modulated in the AD9773 by −ejωt.
The analog quadrature modulator after the AD9773 inherently
modulates by +ejωt.
Region A
Region A is a direct result of the upconversion of the complex
signal near baseband. If viewed as a complex signal, only the
images in Region A remain. The complex Signal A, consisting
of positive frequency components only in the digital domain,
has images in the positive odd Nyquist zones (1, 3, 5, …), as
well as images in the negative even Nyquist zones. The
appearance and rejection of images in every other Nyquist
zone becomes more apparent at the output of the quadrature
modulator. The A images appear on the real and the imaginary
outputs of the AD9773, as well as on the output of the quadrature
modulator, where the center of the spectral plot now represents
the quadrature modulator LO and the horizontal scale now
represents the frequency offset from this LO.
Region B
Region B is the image (complex conjugate) of Region A. If a
spectrum analyzer is used to view the real or imaginary DAC
outputs of the AD9773, Region B appears in the spectrum.
However, on the output of the quadrature modulator, Region B
is rejected.
Region C
Region C is most accurately described as a downconversion, as
the modulating carrier is −ejωt. If viewed as a complex signal, only
the images in Region C remain. This image appears on the real
and imaginary outputs of the AD9773, as well as on the output of
the quadrature modulator, where the center of the spectral plot
now represents the quadrature modulator LO and the horizontal
scale represents the frequency offset from this LO.
Region D
Region D is the image (complex conjugate) of Region C. If a
spectrum analyzer is used to view the real or imaginary DAC
outputs of the AD9773, Region D appears in the spectrum.
However, on the output of the quadrature modulator, Region D
is rejected.
Figure 89 to Figure 96 show the measured response of the AD9773
and AD8345 given the complex input signal to the AD9773 in
Figure 89. The data in these graphs was taken with a data rate of
12.5 MSPS at the AD9773 inputs. The interpolation rate of 4× or 8×
gives a DAC output data rate of 50 MSPS or 100 MSPS. As a result,
the high end of the DAC output spectrum in these graphs is the
first null point for the SIN(x)/x roll-off, and the asymmetry of the
DAC output images is representative of the SIN(x)/x roll-off over
the spectrum. The internal PLL was enabled for these results. In
addition, a 35 MHz third-order low-pass filter was used at the
AD9773/AD8345 interface to suppress DAC images.
An important point can be made by looking at Figure 91 and
Figure 93. Figure 91 represents a group of positive frequencies
modulated by complex +fDAC/4, while Figure 93 represents a
group of negative frequencies modulated by complex −fDAC/4.
When looking at the real or imaginary outputs of the AD9773,
as shown in Figure 91 and Figure 93, the results look identical.
However, the spectrum analyzer cannot show the phase
relationship of these signals. The difference in phase between
the two signals becomes apparent when they are applied to
the AD8345 quadrature modulator, with the results shown in
Figure 92 and Figure 94.
Rev. D | Page 42 of 60
AD9773
0
0
–20
–20
A
B
C
D
A
B
C
–40
–40
–60
–60
–80
–80
D
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
–100
–2.0
2.0
–1.5
B
–1.0
02857-083
–100
–2.0
A
(LO)
fOUT (×fDATA)
–0.5
A
0
0.5
B
1.0
C
1.5
2.0
(LO)
fOUT (×fDATA)
Figure 83. 2x Interpolation, Complex fDAC/4 Modulation
Figure 86. 2x Interpolation, Complex fDAC/8 Modulation
0
0
–20
–20
A
B
C
D
A
B
C
–40
–40
–60
–60
–80
–80
D A
–3.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
02857-084
–100
–4.0
(LO)
fOUT (×fDATA)
–100
–4.0
–3.0
B
–2.0
C D
–1.0
A
0
1.0
B
2.0
C
3.0
4.0
02857-087
D
(LO)
fOUT (×fDATA)
Figure 84. 4x Interpolation, Complex fDAC/4 Modulation
Figure 87. 4x Interpolation, Complex fDAC/8 Modulation
0
0
–20
–20
A
B
C
D
A
B
C
DA
–40
–40
–60
–60
–80
–80
–4.0
–2.0
0
2.0
4.0
6.0
8.0
(LO)
fOUT (×fDATA)
02857-085
–6.0
–100
–8.0
Figure 85. 8x Interpolation, Complex fDAC/4 Modulation
BC
–6.0
–4.0
–2.0
DA
0
BC
2.0
4.0
6.0
8.0
(LO)
fOUT (×fDATA)
Figure 88. 8x Interpolation, Complex fDAC/8 Modulation
Rev. D | Page 43 of 60
02857-088
D
–100
–8.0
CD
02857-086
D
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBm)
–40
–50
–60
–70
–50
–60
–70
–90
–100
–100
0
10
20
30
40
FREQUENCY (MHz)
02857-089
–90
0
20
30
40
FREQUENCY (MHz)
Figure 91. AD9773 Real DAC Output of Complex Input Signal Near
Baseband (Positive Frequencies Only), Interpolation = 4x,
Complex Modulation in AD9773 = +fDAC/4
Figure 89. AD9773 Real DAC Output of Complex Input Signal Near Baseband
(Positive Frequencies Only), Interpolation = 4x, No Modulation in AD9773
0
0
–10
–10
–20
–20
AMPLITUDE (dBm)
–30
–40
–50
–60
–70
–80
–30
–40
–50
–60
–70
–80
–90
–90
760
770
780
790
800
FREQUENCY (MHz)
810
820
830
–100
750
02857-090
–100
750
10
02857-091
–80
–80
AMPLITUDE (dBm)
–40
Figure 90. AD9773 Complex Output from Figure 89, Now Quadrature Modulated
by AD8345 (LO = 800 MHz)
760
770
780
790
800
FREQUENCY (MHz)
810
820
830
02857-092
AMPLITUDE (dBm)
AD9773
Figure 92. AD9773 Complex Output from Figure 91, Now Quadrature Modulated
by AD8345 (LO = 800 MHz)
Rev. D | Page 44 of 60
0
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBm)
–40
–50
–60
–70
–50
–60
–70
–90
–100
–100
0
10
20
30
02857-093
–90
40
FREQUENCY (MHz)
0
40
60
80
FREQUENCY (MHz)
Figure 95. AD9773 Real DAC Output of Complex Input Signal Near
Baseband (Positive Frequencies Only), Interpolation = 8x,
Complex Modulation in AD9773 = +fDAC/8
Figure 93. AD9773 Real DAC Output of Complex Input Signal Near
Baseband (Negative Frequencies Only), Interpolation = 4x,
Complex Modulation in AD9773 = −fDAC/4
0
–10
–10
–20
–20
–30
–30
AMPLITUDE (dBm)
0
–40
–50
–60
–70
–40
–50
–60
–70
–80
–80
–90
–90
760
770
780
790
800
FREQUENCY (MHz)
810
820
830
–100
700
02857-094
–100
750
20
02857-095
–80
–80
AMPLITUDE (dBm)
–40
Figure 94. AD9773 Complex Output from Figure 93, Now Quadrature Modulated
by AD8345 (LO = 800 MHz)
720
740
760
780
800
FREQUENCY (MHz)
820
840
860
02857-096
AMPLITUDE (dBm)
AD9773
Figure 96. AD9773 Complex Output from Figure 95, Now Quadrature Modulated
by AD8345 (LO = 800 MHz)
Rev. D | Page 45 of 60
AD9773
APPLYING THE OUTPUT CONFIGURATIONS
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if IOUTA and/or IOUTB is connected to a load resistor, RLOAD,
referred to AGND. This configuration is most suitable for a
single-supply system requiring a dc-coupled, ground-referred
output voltage. Alternatively, an amplifier could be configured
as an I-V converter, thus converting IOUTA or IOUTB into a
negative unipolar voltage. This configuration provides the best
DAC dc linearity as IOUTA or IOUTB are maintained at ground or
virtual ground.
In many applications, it may be necessary to understand the
equivalent DAC output circuit. This is especially useful when
designing output filters or when driving inputs with finite input
impedances. Figure 97 illustrates the output of the AD9773 and
the equivalent circuit. A typical application where this information
may be useful is when designing an interface filter between
the AD9773 and the Analog Devices AD8345 quadrature
modulator.
AD9773
VOUT+
IOUTB
VOUT–
RA
VSOURCE = 2 V p-p
ROUT = 100 Ω
Note that the output impedance of the AD9773 DAC itself
is greater than 100 kΩ and typically has no effect on the
impedance of the equivalent output circuit.
DIFFERENTIAL COUPLING USING A
TRANSFORMER
An RF transformer can be used to perform a differential-tosingle-ended signal conversion, as shown in Figure 98. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s pass band. An RF transformer such as
the Mini-Circuits T1-1T provides excellent rejection of commonmode distortion (that is, even-order harmonics) and noise over a
wide frequency range. It also provides electrical isolation and the
ability to deliver twice the power to the load. Transformers with
different impedance ratios may also be used for impedance
matching purposes.
IOUTA
DAC
IOUTB
RB
02857-097
VOUT
(DIFFERENTIAL)
RLOAD
The center tap on the primary side of the transformer must be
connected to AGND to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages appearing
at IOUTA and IOUTB (that is, VOUTA and VOUTB) swing symmetrically
around AGND and should be maintained within the specified
output compliance range of the AD9773. A differential resistor,
RDIFF, may be inserted in applications where the output of the
transformer is connected to the load, RLOAD, via a passive
reconstruction filter or cable. RDIFF is determined by the
transformer’s impedance ratio and provides the proper source
termination that results in a low VSWR. Note that approximately
half the signal power dissipates across RDIFF.
RA + RB
VSOURCE =
IOUTFS × (RA + RB)
p-p
MINI-CIRCUITS
T1-1T
Figure 98. Transformer-Coupled Output Circuit
UNBUFFERED DIFFERENTIAL OUTPUT,
EQUIVALENT CIRCUIT
IOUTA
For the typical situation, where IOUTFS = 20 mA and RA and RB
both equal 50 Ω, the equivalent circuit values become
02857-098
The following sections illustrate typical output configurations
for the AD9773. Unless otherwise noted, it is assumed that
IOUTFS is set to a nominal 20 mA. For applications requiring
optimum dynamic performance, a differential output
configuration is suggested. A simple differential output can be
achieved by converting IOUTA and IOUTB to a voltage output by
terminating them to AGND via equal value resistors. This type of
configuration may be useful when driving a differential voltage
input device such as a modulator. If a conversion to a singleended signal is desired and the application allows for ac coupling,
an RF transformer may be useful, or if power gain is required, an
op amp may be used. The transformer configuration provides
optimum high frequency noise and distortion performance. The
differential op amp configuration is suitable for applications
requiring dc coupling, signal gain, and/or level shifting within the
bandwidth of the chosen op amp.
Figure 97. DAC Output Equivalent Circuit
Rev. D | Page 46 of 60
AD9773
DIFFERENTIAL COUPLING USING AN OP AMP
DAC Compliance Voltage/Input Common-Mode Range
An op amp can also be used to perform a differential-to-singleended conversion, as shown in Figure 99. This has the added
benefit of providing signal gain as well. In Figure 99, the
AD9773 is configured with two equal load resistors, RLOAD, of
25 Ω. The differential voltage developed across IOUTA and IOUTB is
converted to a single-ended signal via the differential op amp
configuration. An optional capacitor can be installed across
IOUTA and IOUTB, forming a real pole in a low-pass filter. The
addition of this capacitor also enhances the op amp’s distortion
performance by preventing the DAC’s fast slewing output from
overloading the input of the op amp.
The dynamic range of the AD9773 is optimal when the DAC
outputs swing between ±1.0 V. The input common-mode range
of the AD8345, at 0.7 V, allows optimum dynamic range to be
achieved in both components.
500Ω
225Ω
AD8021
COPT
225Ω
25Ω
500Ω
ROPT
225Ω
02857-099
AVDD
25Ω
Figure 99. Op Amp-Coupled Output Circuit
The common-mode (and second-order distortion) rejection of
this configuration is typically determined by the resistor
matching. The op amp used must operate from a dual supply
since its output is approximately ±1.0 V. A high speed amplifier,
such as the AD8021, capable of preserving the differential
performance of the AD9773 while meeting other system level
objectives (for example, cost, power) is recommended. The op
amp’s differential gain, its gain setting resistor values, and fullscale output swing capabilities should all be considered when
optimizing this circuit. ROPT is necessary only if level shifting is
required on the op amp output. In Figure 99, AVDD, which is
the positive analog supply for both the AD9773 and the op amp,
is also used to level shift the differential output of the AD9773
to midsupply (for example, AVDD/2).
INTERFACING THE AD9773 WITH THE AD8345
QUADRATURE MODULATOR
The AD9773 evaluation board includes an AD8345 and
recommended interface (Figure 105 and Figure 106). On the
output of the AD9773, R9 and R10 convert the DAC output
current to a voltage. R16 may be used to execute a slight
common-mode shift if necessary. The (now voltage) signal is
applied to a low-pass reconstruction filter to reject DAC images.
The components installed on the AD9773 provide a 35 MHz
cutoff but may be changed to fit the application. A balun (MiniCircuits ADTL1-12) is used to cross the ground plane boundary
to the AD8345. Another balun (Mini-Circuits ETC1-1-13) is
used to couple the LO input of the AD8345. The interface
requires a low ac impedance return path from the AD8345, so a
single connection between the AD9773 and AD8345 ground
planes is recommended.
The performance of the AD9773 and AD8345 in an image
reject transmitter, reconstructing three WCDMA carriers, can
be seen in Figure 100. The LO of the AD8345 in this application
is 800 MHz. Image rejection (50 dB) and LO feedthrough
(−78 dBFS) have been optimized with the programmable
features of the AD9773. The average output power of the digital
waveform for this test was set to −15 dBFS to account for the
peak-to-average ratio of the WCDMA signal.
0
The AD9773 architecture was defined to operate in a transmit
signal chain using an image reject architecture. A quadrature
modulator is also required in this application and should be
designed to meet the output characteristics of the DAC as much
as possible. The AD8345 from Analog Devices meets many of
the requirements for interfacing with the AD9773. As with any
DAC output interface, there are a number of issues that have to
be resolved. The following sections list some of these major issues.
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
762.5
782.5
802.5
FREQUENCY (MHz)
822.5
842.5
Figure 100. AD9773/AD8345 Synthesizing a Three-Carrier
WCDMA Signal at an LO of 800 MHz
Rev. D | Page 47 of 60
02857-100
IOUTB
The matching of the DAC output to the common-mode input
of the AD8345 allows the two components to be dc-coupled,
with no level shifting necessary. The combined voltage offset of
the two parts can therefore be compensated via the AD9773
programmable offset adjust. This allows excellent LO cancellation at the AD8345 output. The programmable gain adjust
allows for optimal image rejection as well.
AMPLITUDE (dBm)
IOUTA
DAC
Gain/Offset Adjust
AD9773
EVALUATION BOARD
The AD9773 evaluation board allows easy configuration of the
various modes, programmable via the SPI port. Software is
available for programming the SPI port from Windows 95®,
Windows 98®, or Windows NT®/2000. The evaluation board
also contains an AD8345 quadrature modulator and support
circuitry that allows the user to optimally configure the AD9773
in an image reject transmit signal chain.
Figure 101 through Figure 104 describe how to configure the
evaluation board in the one-port and two-port input modes
with the PLL enabled and disabled. Refer to Figure 105 through
Figure 114, the schematics, and the layout for the AD9773
evaluation board for the jumper locations described below. The
AD9773 outputs can be configured for various applications by
referring to the following instructions.
DAC DIFFERENTIAL OUTPUTS
Transformers T2 and T3 should be in place. Note that the lower
band of operation for these transformers is 300 kHz to 500 kHz.
Jumpers 4, 8, 13 to 17, and 28 to 30 should remain unsoldered.
The outputs are taken from S3 and S4.
USING THE AD8345
Remove Transformers T2 and T3. Jumpers JP4 and Jumpers 28
to 30 should remain unsoldered. Jumpers 13 to 16 should be
soldered. The desired components for the low-pass interface
filters L6, L7, C55, and C81 should be in place. The LO drive is
connected to the AD8345 via J10 and the balun T4; AD8345
output is taken from J9.
DAC SINGLE-ENDED OUTPUTS
Remove transformers T2 and T3. Solder jumper link JP4 or
JP28 to look at the DAC1 outputs. Solder jumper link JP29 or
JP30 to look at the DAC2 outputs. Jumper 8 and Jumpers 13 to
17 should remain unsoldered. Jumpers JP35 to JP38 may be
used to ground one of the DAC outputs while the other is
measured single-ended. Optimum single-ended distortion
performance is typically achieved in this manner. The outputs
are taken from S3 and S4.
Rev. D | Page 48 of 60
AD9773
LECROY
TRIG
PULSE
INP
GENERATOR
SIGNAL GENERATOR
DATACLK
INPUT CLOCK
AWG2021
OR
DG2020
CLK+/CLK–
40-PIN RIBBON CABLE
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9773
JUMPER CONFIGURATION FOR TWO-PORT MODE, PLL ON
SOLDERED/IN
×
UNSOLDERED/OUT
×
×
×
×
×
×
×
×
×
×
×
×
NOTES
1. TO USE PECL DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25
AND JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT
PIN 53, JP46 AND JP47 SHOULD BE SOLDERED. FOR MORE INFORMATION, SEE THE
TWO-PORT DATA INPUT MODE SECTION.
02857-101
JP1 –
JP2 –
JP3 –
JP5 –
JP6 –
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
Figure 101. Test Configuration for AD9773 in Two-Port Mode with PLL Enabled, Signal Generator Frequency = Input Data Rate,
DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate
LECROY
TRIG
PULSE
INP
GENERATOR
SIGNAL GENERATOR
ONEPORTCLK
INPUT CLOCK
AWG2021
OR
DG2020
CLK+/CLK–
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9773
JUMPER CONFIGURATION FOR ONE-PORT MODE, PLL ON
SOLDERED/IN
×
UNSOLDERED/OUT
×
×
×
×
×
×
×
×
×
×
×
×
NOTES
1. TO USE PECL DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
02857-102
JP1 –
JP2 –
JP3 –
JP5 –
JP6 –
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
Figure 102. Test Configuration for AD9773 in One-Port Mode with PLL Enabled, Signal Generator Frequency = One-Half Interleaved Input Data Rate,
ONEPORTCLK = Interleaved Input Data Rate, DAC Output Data Rate = Signal Generator Frequency × Interpolation Rate
Rev. D | Page 49 of 60
AD9773
LECROY
TRIG
PULSE
INP
GENERATOR
SIGNAL GENERATOR
DATACLK
INPUT CLOCK
AWG2021
OR
DG2020
CLK+/CLK–
40-PIN RIBBON CABLE
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9773
JUMPER CONFIGURATION FOR TWO-PORT MODE, PLL OFF
SOLDERED/IN
×
UNSOLDERED/OUT
×
×
×
×
×
×
×
×
×
×
×
×
NOTES
1. TO USE PECL DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
2. IN TWO-PORT MODE, IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT PIN 8, JP25
AND JP39 SHOULD BE SOLDERED. IF DATACLK/PLL_LOCK IS PROGRAMMED TO OUTPUT
PIN 53, JP46 AND JP47 SHOULD BE SOLDERED. FOR MORE INFORMATION, SEE THE
TWO-PORT DATA INPUT MODE SECTION.
02857-103
JP1 –
JP2 –
JP3 –
JP5 –
JP6 –
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
Figure 103. Test Configuration for AD9773 in Two-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency,
DATACLK = Signal Generator Frequency/Interpolation Rate
LECROY
TRIG
PULSE
INP
GENERATOR
SIGNAL GENERATOR
ONEPORTCLK
INPUT CLOCK
AWG2021
OR
DG2020
CLK+/CLK–
DAC1, DB11–DB0
DAC2, DB11–DB0
AD9773
JUMPER CONFIGURATION FOR ONE-PORT MODE, PLL OFF
SOLDERED/IN
×
UNSOLDERED/OUT
×
×
×
×
×
×
×
×
×
×
×
×
NOTES
1. TO USE PECL DRIVER (U8), SOLDER JP41 AND JP42 AND REMOVE TRANSFORMER T1.
02857-104
JP1 –
JP2 –
JP3 –
JP5 –
JP6 –
JP12 –
JP24 –
JP25 –
JP26 –
JP27 –
JP31 –
JP32 –
JP33 –
Figure 104. Test Configuration for AD9773 in One-Port Mode with PLL Disabled, DAC Output Data Rate = Signal Generator Frequency,
ONEPORTCLK = Interleaved Input Data Rate = 2x Signal Generator Frequency/Interpolation Rate
Rev. D | Page 50 of 60
Figure 105. AD8345 Circuitry on AD9773 Evaluation Board
O1P
O1N
2
+ C72
10V
10μF
02857-105
BCASE
VDDM
O2P
C54
DNP
CC0603
C78
0.1μF
C75
0.1μF
LC0805
C73
L5 DNP
DNP
CC0805
LC0805
L4
DNP
C35
100pF CC0603
L7
DNP
LC0805
3
P
1
T6
S
6
4
2
2
12
11 10
R34
DNP
R33
51Ω
AD8345
3
4
RC0603
R36
51Ω
1
C77
100pF
CC0603
RC0603
7
8
P
CC0603
C80
DNP
T4
R37
DNP
RC0603
JP20
S
5
4
JP18
R26
1kΩ
VDDM
2
9
C76
100pF
3 ETC1-1-13
6
CC0603
R35
51Ω
5
U2
CC0603
C74
100pF
RC0603
JP19
CC0603
RC0603
RC0603
15 14 13
4
1
16
6
S
T5
P
3
1
CC0805
QBBP
IBBP
C81
DNP
G4B
CC0805
QBBN
IBBN
LC0805
G1B
C55
DNP
LOIN
G2
O2N
G4A
G1A
C79
DNP
RC0603
ENBL
ADTL1-12
CC0603
VOUT
LOIP
G3
VPS1
VPS2
ADTL1-12
Rev. D | Page 51 of 60
CC0805
R32
51Ω
RC0603
L6
DNP
2
R30
DNP
2
2
J9
DGND2; 3, 4, 5
JP21
JP7
2
2
LOCAL OSC INPUT
R28 DGND2; 3, 4, 5
0Ω
J10
RC0603
RC0603
R23
0Ω
MODULATED OUTPUT
J7
J3
J6
J4
J5
J8
W12
W11
CGND
DCASE
CLKVDD_IN
AGND
DCASE
AVDD_IN
DGND
DCASE
DVDD_IN
DGND2
DCASE
VDDMIN
+ C63
16V
22μF
+ C64
16V
22μF
+ C65
16V
22μF
+ C28
16V
22μF
2
c
LC1210
L1
FERRITE
LC1210
L2
FERRITE
LC1210
L3
FERRITE
LC1210
L8
FERRITE
CC0805
CC0805
CC0805
CC0805
POWER INPUT FILTERS
DCASE
DCASE
C69
0.1μF
DCASE
JP11
C68
0.1μF
JP10
C67
0.1μF
JP9
C32
0.1μF
+ C62
16V
22μF
TP5
BLK
+ C61
16V
22μF
TP3
BLK
+ C66
16V
22μF
JP43
VDDM
JP44
TP7
BLK
TP6
RED
CLKVDD
TP4
RED
AVDD
TP2
RED
DVDD
JP45
AD9773
Figure 106. AD9773 Clock, Power Supplies, and Output Circuitry
JP12
CX2
CX1
02857-106
13
12
JP3
IQ
JP40
JP27
JP5
C29
0.1μF
JP24
JP39
JP25
RC0603
R39
1kΩ JP32
R5
49.9Ω
TP14
WHT
DVDD; 14
DGND; 7
11
DVDD; 14
DGND; 7
RC0603
R1
200Ω
DVDD
DVDD
DVDD
DVDD
c
+ C7
BCASE
10μF
6.3V
+ C8
10μF
6.3V
BCASE
+ C9
10μF
6.3V
BCASE
+ C10
10μF
6.3V
C42
0.1μF
CC0603
0.001μF
CC0603
C23
0.001μF
CC0603
C24
0.001μF
CC0603
C25
0.001μF
CC0603
C26
CLKN
CLKP
0.1μF
C11
CC0603
0.1μF
C12
BCASE
BCASE
C1 +
10μF
6.3V
R38 10kΩ
JP26
BD14
74VCX86
JP31
12
11
U4 13
U3
RC0603
JP23
74VCX86 CX3
C45
0.01μF
JP34
OPCLK
AGND; 3, 4, 5
OPCLK
S5
IQ
S6
DGND; 3, 4, 5
OPCLK_3
BD15
1
2
3
JP22
T1
T1-1T
JP33
ADCLK
6
5
4
ACLKX c CGND; 3, 4, 5
S1
CLKIN
JP2
JP1
C13
0.1μF
CC0603
R40
DVDD
5kΩ
DGND; 3, 4, 5
DATACLK
S2
c
TP15
WHT
R3
1kΩ
BD11
BD10
BD09
BD08
BD13
BD12
AD03
AD02
AD01
AD00
AD09
AD08
AD07
AD06
AD05
AD04
AD10
AD13
AD12
AD11
AD15
AD14
c
CC0603
1pF
C27
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
P2D1
P2D2
P2D3
P2D4
P2D5
VSSD5
VDDD5
P2D6
P2D7
RESET
SP-CSB
SP-CLK
SP-SDI
SP-SDO
VSSD6
VDDD6
P2D0
AD9773+TSP
CC0805
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
0.1μF
C36
VDDA6
VSSA10
VDDA5
VSSA9
VDDA4
VSSA8
VSSA7
IOUT1P
IOUT1N
VSSA6
VSSA5
IOUT2P
IOUT2N
VSSA4
VSSA3
VDDA3
VSSA2
VDDA2
VSSA1
VDDA1
FSADJ1
FSADJ2
REFOUT
CC0805
DVDD
VDDC1
LF
VDDC2
VSSC1
CLKP
CLKN
VSSC2
DCLK-PLLL
VSSD1
VDDD1
P1D15
P1D14
P1D13
P1D12
P1D11
P1D10
VSSD2
VDDD2
U1
P1D9
P1D8
P1D7
P1D6
P1D5
P1D4
VSSD3
VDDD3
P1D3
P1D2
P1D1
P1D0
P2D15-IQSEL
P2D14-OPCLK
P2D13
P2D12
VSSD4
VDDD4
P2D11
P2D10
P2D9
P2D8
CC0603
CLKVDD
CC0603
0.1μF
CC0805
C37
CC0603
BD07
BD06
C22
CC0603
0.001μF
CC0805
0.1μF
CC0603
C16
TP8
WHT
C6 +
10μF
6.3V
C5 +
10μF
6.3V
BCASE
DVDD
BCASE
JP38
JP36
J35
J37
IQ
JP46
R7
R8
2kΩ
1kΩ
0.01% 0.01%
+ C3
10μF
6.3V
DVDD
BCASE
0.1μF
+ C2
10μF
6.3V
AVDD
0.1μF
C41
AVDD
BCASE
C15
C4 +
10μF
6.3V
TP9
WHT
0.1μF
0.1μF
BCASE
C14
C58
DNP
CC0603
C17
CC0603
CC0805
0.1μF
C40
C58
DNP
CC0603
C19
0.1μF
C39
R6 0.1μF
1kΩ
BD00
C21
BD01
CC0603
BD02 0.001μF
BD03
BD04
BD05
SPCSP
SPCLK
SPSDI
SPSDO
TP10
WHT
0.1μF
C18
C59
DNP
C57
DNP
0.1μF
CC0603
C20
TP11
WHT
CC0805
CC0805
0.1μF
C38
CC0603
CC0603
RC0603
RC0603
CC0605
Rev. D | Page 52 of 60
CC0805
RC1206
CC0603
R2
1kΩ
5
6
2
1
U4
9
10
RC0603
RC0603
74VCX86
R11
51kΩ
JP47
R17
10kΩ
O1N
O1P
O2N
O2P
AGND; 3, 4, 5
OUT 2
S4
R42
49.9kΩ
RC1206
AGND; 3, 4, 5
OUT1
S3
RC0603
CC0603
JP8
SPSDO
RC0603
CC0603
R43
49.9kΩ
T1-1T
JP17
R12
C70
51kΩ
0.1μF
4
3
T3
JP30
DVDD; 14
DGND; 7
8
JP14
JP15
JP29
JP16
JP13
5
6
2
1
R16
10kΩ
4
T1-1T
T2
JP28
JP4
RC0603
RC0603
C70
0.1μF
3
R9
51kΩ
R10
51kΩ
AD9773
02857-107
RIBBON
J1
Rev. D | Page 53 of 60
31
33
35
37
39
32
34
36
38
40
RC1206
R15
220Ω
29
30
21
22
27
19
20
28
17
18
25
15
16
26
13
14
23
11
12
24
9
10
5
6
7
3
4
8
1
2
DATA-A
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
RP1
1
RP1
2
RP1
3
RP1
4
RP1
5
RP1
6
RP1
7
RP1
8
RP2
1
RP2
2
RP2
3
RP2
4
RP2
5
RP2
6
RP2
7
RP2
8
22Ω
16
22Ω
15
22Ω
14
22Ω
13
22Ω
12
22Ω
11
22Ω
10
22Ω
9
22Ω
16
22Ω
15
22Ω
14
22Ω
13
22Ω
12
22Ω
11
22Ω
10
22Ω
9
RCOM
RP5
50Ω
10
1
R1 R2 R3 R4 R5 R6 R7 R8 R9
2
3
4
5
6
7
8
9
ADCLK
OPCLK
Figure 107. AD9773 Evaluation Board Input (A Channel) and Clock Buffer Circuitry
K
2
74LCX112
U7
15
CLR
CLK
J
Q 5
1
OPCLK_2
Q 6
2
U4
OPCLK_3
3
DVDD; 14
AGND; 7
74VCX86
11
J
K
14
CLR
CLK
74LCX112
U7
13
12
10
PRE
1
3
6
C52 +
4.7μF
6.3V
DVDD
C31 +
4.7μF
6.3V
DVDD
CX3
C30 +
4.7μF
6.3V
DVDD
AGND; 8
DVDD; 16
Q 7
Q 9
DVDD; 14
AGND; 7
74VCX86
U4
8
DVDD; 14
AGND; 7
PRE
5
4
U3
6
DVDD; 14
AGND; 7
74VCX86
U3
3
DVDD; 14
AGND; 7
74VCX86
U3
74VCX86
4
DVDD
RP8
DNP
AD00
AD01
AD02
AD03
AD04
AD05
AD06
9
10
5
4
2
1
AD07
CX2
CX1
AD08
AD09
AD10
AD11
AD12
AD13
AD14
AD15
RP7
10 DNP
R1 R2 R3 R4 R5 R6 R7 R8 R9
9 10 RP6
1 2 3 4 5 6 7 8 9 10
50Ω
RCOM
RCOM
R1 R2 R3 R4 R5 R6 R7 R8 R9
R1 R2 R3 R4 R5 R6 R7 R8 R9
1
1
RCOM
ACASE
ACASE
ACASE
C53
0.1μF
C34
0.1μF
C33
0.1μF
CC0805
CC0805
CC0805
AD9773
Rev. D | Page 54 of 60
02857-108
33
35
37
39
34
36
38
40
RIBBON
J2
31
32
23
24
29
21
22
30
19
20
27
17
18
28
15
16
25
13
14
26
11
7
8
12
5
6
9
3
4
10
1
2
DATA-B
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP4 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
RP3 22Ω
9
10
11
12
13
14
15
16
9
10
11
12
13
14
15
2
3
4
5
6
7
8
9
BD00
BD01
BD02
BD03
BD04
BD05
BD06
BD07
BD08
BD09
BD10
BD11
BD12
BD13
BD14
BD15
RP9
10 DNP
R1 R2 R3 R4 R5 R6 R7 R8 R9
16
RCOM
RP12
10 50Ω
1
R1 R2 R3 R4 R5 R6 R7 R8 R9
Figure 108. AD9773 Evaluation Board Input (B Channel) and SPI Port Circuitry
ACASE
DVDD
SPSDO
SPSDI
SPCLK
SPCSB
+
C43
4.7μF CC805
6.3V
9 10 RP11
1 2 3 4 5 6 7 8 9 10
RP10
50Ω
RCOM
DNP
RCOM
R1 R2 R3 R4 R5 R6 R7 R8 R9
R1 R2 R3 R4 R5 R6 R7 R8 R9
1
1
RCOM
C50
0.1μF
2
c
U5
+ C49
4.7μF
6.3V
U5
U5
U5
10
U5
74AC14
8
U5
U6
12
DGND; 7
DVDD; 14
U6
6
U6
DGND; 7
74AC14 DVDD; 14
5
DGND; 7
74AC14 DVDD; 14
3
U6
8
U6
DGND; 7
74AC14 DVDD; 14
9
DGND; 7
74AC14 DVDD; 14
11
10
13
9
DGND; 7
DVDD; 14
11
DGND; 7
DVDD; 14
12
RC0805
ACASE
DVDD
+
RC0805
C44
4.7μF
6.3V
RC0805
R24
DNP RC0805
R22
DNP
JP41
JP42
RC0805
R20
DNP
R21
DNP RC0805
RC0805
R45
9kΩ
R48
9kΩ
R50
9kΩ
CLKVDD; 8
CGND; 5
4
2
DGND; 7
DVDD; 14 74AC14
5
CC805
C48
1nF
R19
100Ω
CC805
MC100EPT22
3
6 U8
4
R18
200Ω
RC0805
DGND; 7
74AC14
DVDD; 14
3
c
1
2
CGND; 5
CLKVDD; 8
U8
13
c
RC0805
MC100EPT22
c
C47
1nF
DGND; 7
74AC14 DVDD; 14
U6
C60
0.1μF
c
7
R13
120Ω
DGND; 7
DVDD; 14
1
CC805
RC0805
R4
120Ω
R14
200Ω
DGND; 7
74AC14 DVDD; 14
1
74AC14
6
74AC14
4
74AC14
ACASE
CLKDD
ACLKX
CC805
C46
0.1μF
RC0805
CLKVDD
CLKVDD
CLKN
CLKP
CLKVDD
CC805
6
5
4
3
2
C51
0.1μF
SPI PORT
P1
1
c
c
AD9773
02857-109
AD9773
02857-110
Figure 109. AD9773 Evaluation Board Components, Top Side
Figure 110. AD9773 Evaluation Board Components, Bottom Side
Rev. D | Page 55 of 60
02857-111
AD9773
02857-112
Figure 111. AD9773 Evaluation Board Layout, Layer One (Top)
Figure 112. AD9773 Evaluation Board Layout, Layer Two (Ground Plane)
Rev. D | Page 56 of 60
02857-113
AD9773
02857-114
Figure 113. AD9773 Evaluation Board Layout, Layer Three (Power Plane)
Figure 114. AD9773 Evaluation Board Layout, Layer Four (Bottom)
Rev. D | Page 57 of 60
AD9773
OUTLINE DIMENSIONS
14.20
14.00 SQ
13.80
1.20
MAX
0.75
0.60
0.45
12.20
12.00 SQ
11.80
61
61
80
60
1
80
1
60
PIN 1
EXPOSED
PAD
TOP VIEW
(PINS DOWN)
BOTTOM VIEW
0° MIN
1.05
1.00
0.95
0.15
0.05
SEATING
PLANE
6.00
BSC SQ
0.20
0.09
7°
3.5°
0°
0.08 MAX
COPLANARITY
(PINS UP)
20
41
40
21
VIEW A
20
41
21
40
0.50 BSC
LEAD PITCH
0.27
0.22
0.17
COMPLIANT TO JEDEC STANDARDS MS-026-ADD-HD
060806-A
VIEW A
ROTATED 90° CCW
`
Figure 115. 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
(SV-80-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9773BSV
AD9773BSVRL
AD9773BSVZ1
AD9773BSVZRL1
AD9773-EB
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
Evaluation Board
Z = RoHS Compliant Part.
Rev. D | Page 58 of 60
Package Option
SV-80-1
SV-80-1
SV-80-1
SV-80-1
AD9773
NOTES
Rev. D | Page 59 of 60
AD9773
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02857-0-10/07(D)
Rev. D | Page 60 of 60