WRD-YKD-5W Series 5W, WIDE INPUT ISOLATED & REGULATED TWIN OUTPUT DIP 24 DC-DC CONVERTER DIP24 PRODUCT PROGRAM Input Part 2:1 wide input voltage range ◆ Twin output ◆ Operating temperature: -40℃ to + 85℃ ◆ UL94-V0 package ◆ No external component required ◆ Industry standard pin out ◆ Short circuit protection(automatic recovery) ◆ ◆ Five-sided metal shielding Efficiency Nomina Range Max* WRD120505YKD-5W l 12 9.0-18 22 25 5/5 500/500 50/50 76 WRD120909YKD-5W 12 9.0-18 22 25 9/9 278/278 28/28 78 WRD121212YKD-5W 12 9.0-18 22 25 12/12 208/208 21/21 80 WRD121515YKD-5W 12 9.0-18 22 25 15/15 167/167 17/17 81 WRD122424YKD-5W 12 9.0-18 22 25 24/24 104/104 10/10 82 WRD240505YKD-5W 24 18-36 40 15 5/5 500/500 50/50 76 WRD240512YKD-5W 24 18-36 40 15 5/12 500/208 50/21 77 WRD241212YKD-5W 24 18-36 40 15 12/12 208/208 21/21 80 WRD241515YKD-5W 24 18-36 40 15 15/15 167/167 17/17 79 WRD242405YKD-5W 24 18-36 40 15 24/05 104/500 10/50 81 WRD242424YKD-5W 24 18-36 40 15 24/24 104/104 10/10 81 WRD480505YKD-5W 48 36-72 80 10 5/5 500/500 50/50 76 WRD480512YKD-5W 48 36-72 80 10 5/12 500/208 50/21 78 WRD480909YKD-5W 48 36-72 80 10 9/9 278/278 28/28 78 WRD481212YKD-5W 48 36-72 80 10 12/12 208/208 21/21 80 WRD481515YKD-5W 48 36-72 80 10 15/15 167/167 17/17 81 48 36-72 80 10 24/24 104/104 10/10 82 Number FEATURES Output No-load Current (mA,Typ) Voltage(VDC) Voltage (VDC) Current(MA) Max Min. (%,Typ) ◆ MTBF>1,000,000 hours WRD482424YKD-5W ◆ No heat sink required *Input voltage can't exceed this value, or will cause the permanent damage. ◆ RoHS Compliance MODEL SELECTION WR D①12②05③05④Y⑤ KD⑥-5W⑦ WRD ①Product Series ②Input Voltage ③1st Output Voltage ④2nd Output Voltage ⑤Wide (2:1) Input Range ⑥Package Style ⑦Rated Power APPLICATIONS The WRD_YKD-5W series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1)Where the voltage of the input power supply is wide range (voltage range≤2:1); 2)Where isolation is necessary between input and output (Isolation Voltage≤1500VDC); 3)Where isolation is necessary between Vout1 and Vout2 (Isolation Voltage≤1000VDC); 4)Where the regulation of the output voltage and the output ripple noise are demanded. PRODUCT ID DESCRIPTION COMMON SPECIFICATIONS Item Test Conditions Min. Typ. Storage humidity Max. Units 95 % Operating temperature -40 85 Storage Temperature -55 125 Temp. rise at full load Lead temperature Cooling Case Material Short circuit protection MTBF 1.5mm from case for 10 seconds 300 Free Air Convection Plastic (UL94-V0) Continuous, Automatic Recovery 1000 Weight K hours 15 MICRODC R ESERVES THE COPYRIGHT http://www.microdc.cn ℃ 15 Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 3 g WRD-YKD-5W Series TYPICAL CHARACTERISTICS ISOLATION SPECIFICATIONS Item Test Conditions Min. Isolation voltage Tested for 1 minute and 1mA max 1500 Isolation resistance Test at 500VDC 1000 Isolation capacitance Input/Output, 100KHz/1V Typ. Max. Units VDC MΩ 100 pF *Supply voltage must be discontinued at the end of short circuit duration. OUTPUT SPECIFICATIONS Item Test Conditions Min. 0.5 Typ. Max. Units 5 W ±1 ±3 Output power Refer to product program Main output voltage accuracy Refer to recommended circuit Vice-output voltage accuracy Refer to recommended circuit ±3 ±5 Load regulation From 10% to 100% load ±0.5 ±1* ±0.2 % ±0.5 Line regulation Input voltage from low to high Temperature drift (Vout) Refer to recommended circuit Ripple** 20MHz Bandwidth 20 50 Noise** 20MHz Bandwidth 75 150 Switching frequency 100% load, input voltage range 300 ±0.03 %/℃ mVp-p KHz *Dual output models unbalanced load: ±5%. RECOMMENDED CIRCUIT **Test ripple and noise by “ parallel cable ” method. See detailed operation instructions at Testing of PoweConverter section, application notes. APPLICATION NOTE 1) Requirement On Output Load In order to ensure the product operate efficiently and reliably, in addition to a max load (namely full load), a minimum load is specified for this kind of DC/DC converter. Make sure the specified range of input voltage is not exceeded, the minimum output load no less than 10% load. If the actual load is less than the specified minimum load, the output ripple may increase sharply while its efficiency and reliability will reduce greatly. If the actual output power is very small, please add an appropriate resistor as extra loading, or contact our company for other lower output power products. 2) Recommended Circuit All the WRD-YKD-5W Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load (see Figure 1). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high, or may cause start-up problem. If you want to use the products in high EMI, please choose our metal packaged products. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). General: Cin: 5V,12V 100µF 24V&48V 22µF/10µF Cout: 10µF/100mA 3) Input Current While using unstable power source, please ensure the output voltage and ripple voltage do not exceed indexes of the converter. The preceding power source must be able to provide for converter sufficient starting current Ip (Figure 2). General: Ip≤1.4*Iin-max 4) No parallel connection or plug and play http://www.microdc.cn EXTERNAL CAPACITOR TABLE (TABLE 1) Output External Capacitor Table (Table 1) Vout(VDC) Cout(uF) 5 680 9 470 12 330 15 220 24 100 Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 3 WRD-YKD-5W Series OUTLINE DIMENSIONS ＆ FOOTPRINT DETAILS MECHANICAL DIMENSIONS RECOMMENDED FOOTPRINT(TOP VIEW) TUBE OUTLINE DIMENSIONS RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 REACH COMPLIANT INFORMATION E-mail:[email protected] Website: www.microdc.cn http://www.microdc.cn This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 3