Datenblatt

For more information, please visit the product page.
PART NUMBER: CPE-267
page
1 of 5
date
02/2010
DESCRIPTION: piezo audio transducer
SPECIFICATONS
operating frequency
rated voltage
operating voltage range
current consumption
sound pressure level
tone
operating tempurature
storage tempurature
dimensions
weight
material
terminal
RoHS
dustproof/waterproof level
2.8 ± 0.5 kHz
12 V dc
6 ~ 14 V dc
35 mA max.
at 12 V dc
85 dB min.
at 30 cm/12 V dc
continuous
at 12 V dc
-30 ~ +85° C
-40 ~ +95° C
ø25 x H16 mm
41 g max.
ABS UL-94 1/16” HB high heat (black)
wire type
yes
IP67
IEC standard 529 edition 2.0(1989)
APPEARANCE DRAWING
tolerance: ±0.5
units: mm
CUI,INC. G
˨˟˄˃˃ˊ˟˙ʳ˅˅˔˪˚
˥˸˷
˕˿˴˶˾
ʻ˦˸˴˿˸˷ʳ˧̌̃˸ʼ
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
For more information, please visit the product page.
page
2 of 5
date
02/2010
DESCRIPTION: piezo audio transducer
PART NUMBER: CPE-267
VOLTAGE: SOUND PRESSURE LEVEL / CURRENT CONSUMPTION CHARACTERISTICS
˄˃ˈ
˄˃˃
ˣ
ˌ˃
ˋˈ
ˋ˃
ˊˈ
ˆˈ
˜
ˊ˃
ˆ˃
˅ˈ
˅˃
˄ˈ
˄˃
ˉ
ˋ
˄˃
˄˅
˄ˇ
˩̂˿̇˴˺˸ʻ˩˗˖ʼ
MEASUREMENT METHOD
S.P.L. Measuring Circuit
Mic: RION S.P.L. meter UC30 or equivalent
S.G.: Hewlett Packard 33120A function generator or equivalent
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
˄ˉ
˖̈̅̅˸́̇ʳ˖̂́̆̈̀̃̇˼̂́ʻ̀˔ʼ
˦̂̈́˷ʳˣ̅˸̆̆̈̅˸ʳ˟˸̉˸˿ʻ˷˕ʼʳʳ
ˌˈ
For more information, please visit the product page.
page
3 of 5
date
02/2010
DESCRIPTION: piezo audio transducer
PART NUMBER: CPE-267
MECHANICAL CHARACTERISTICS
item
solderability
(connector excepted)
lead wire pull strength
vibration
drop test
test condition
Lead terminals are immersed in rosin for
5 seconds and then immersed in solder bath
of 270 ±5°C for 3 ±0.5 seconds.
The pull force shall be applied to double lead
wire:
Horizontal 3.0N (0.306 kg) for 30 seconds
Vertical 2.0N (0.204 kg) for 30 seconds
The buzzer shall be measured after applying
a vibration amplitude of 1.5 mm with 10 to
55 Hz band of vibration frequency to each of
the 3 perpendicular directions for 2 hours.
The part will be dropped from a height of
75 cm onto a 40 mm thick wooden board 3
times in 3 axes (X, Y, Z) for a total of 9 drops.
evaluation standard
90% min. of the lead terminals
will be wet with solder
(except the edge of the terminal).
test condition
After being placed in a chamber at +95°C for
240 hours.
After being placed in a chamber at -40°C for
240 hours.
After being placed in a chamber at +40°C and
90±5% relative humidity for 240 hours.
The part shall be subjected to 5 cycles. One
cycle will consist of:
evaluation standard
No damage or cutting off.
The value of oscillation
frequency/current consumption
should be ±10% of the initial
measurements. The SPL should
be within ±10dB compared with
the initial measurement.
ENVIRONMENT TEST
item
high temp. test
low temp. test
humidity test
temp. cycle test
+95к
+25к
+25кʳ
-40к
0.5hr
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
0.5hr 0.25 0.5hr 0.5hr 0.5hr 0.25
3hours
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
For more information, please visit the product page.
page
4 of 5
date
02/2010
DESCRIPTION: piezo audio transducer
PART NUMBER: CPE-267
RELIABILITY TEST
item
operating (life test)
test condition
1. Continuous life test:
The part will be subjected to 48 hours of
continuous operation at +70°C with rated
voltage applied.
2. Intermittent life test:
A duty cycle of 1 minute on, 1 minute off, a
minimum of 5,000 times at room temp
(+25 ±2°C) with rated voltage applied.
evaluation standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to
the initial measurements.
TEST CONDITIONS
standard test condition
judgement test condition
a) tempurature: +5 ~ +35°C
a) tempurature: +25 ±2°C
b) humidity: 45 - 85%
b) humidity: 60 - 70%
c) pressure: 860-1060 mbar
c) pressure: 860-1060 mbar
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
For more information, please visit the product page.
PART NUMBER: CPE-267
page
5 of 5
date
02/2010
DESCRIPTION: piezo audio transducer
PACKAGING
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
Similar pages