Datenblatt

For more information, please visit the product page.
Part No: CEP-4411AC
Date: 2/06/2007
Unit: mm
Description: piezo audio indicator
Page No: 1 of 4
Specifications
Resonant frequency
Operating voltage
Current consumption
Sound pressure level
Rated Voltage
Tone
Operating tempurature
Storage tempurature
Dimensions
Weight
Material
Terminal
RoHS
2.8 ± 0.5 KHz
30 ~ 120.0 V ac/V dc
7 mA max.
88 db min.
110 V ac
Continuous
-20 ~ +60° C
-30 ~ +70° C
ø41.8 x H22.0 mm
22.2 g max.
ABS UL-94 1/16” HB High
Wire type
yes
non-polarized
at 110 V ac
at 30 cm / 110 V ac
See attached drawing
Heat (Black)
See attached drawing
Appearance Drawing
Tolerance: ±0.5
Phone: 800.275.4899
Fax: 503.612.2383
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
For more information, please visit the product page.
Part No: CEP-4411AC
Date: 2/06/2007
Unit: mm
Description: piezo audio indicator
Page No: 2 of 4
Measurement Method
S.P.L. Measuring Circuit
Mic: RION S.P.L. meter UC 30 or equivalent
S.G.: Hewlett Packard 33120A Function Generator or equivalent
Mechanical Characteristics
Item
Solderability
Terminal Mechanical Strength
Vibration
Drop Test
Phone: 800.275.4899
Evaluation Standard
Test Condition
90% min. of the stripped wires
Stripped wires of lead wires are immersed in
will be wet with solder.
rosin for 5 seconds and then immersed in
a solder bath of +270 ±5°C for 3 ±0.5 seconds. (Except the edge of the terminal)
The pull force should be applied to the double
No damage or cutting off.
lead wire:
Horizontal 3.0N (0.306kg) for 30 seconds
Vertical 2.0N (0.204kg) for 30 seconds
The value of oscillation
The buzzer will be measured after applying
frequency/current consumption
a vibration amplitude of 1.5 mm with 10 to
should be ±10% of the initial
55 Hz band of vibration frequency to each of
measurements. The SPL should
the 3 perpendicular directions for 2 hours.
The part will be dropped from a height of 75 cm be within ±10dB compared with
the initial measurement.
onto a 40 mm thick wooden board 3 times in
3 axis (X, Y, Z) for a total of 9 drops.
Fax: 503.612.2383
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
For more information, please visit the product page.
Date: 2/06/2007
Part No: CEP-4411AC
Unit: mm
Description: piezo audio indicator
Page No: 3 of 4
Environment Test
Item
High temp. test
Low temp. test
Humidity test
Temp. cycle test
Test Condition
After being placed in a chamber at +70°C for
240 hours.
After being placed in a chamber at -30°C for
240 hours.
After being placed in a chamber at +40°C and
90±5% relative humidity for 240 hours.
The part shall be subjected to 5 cycles. One
cycle will consist of:
Evaluation Standard
Test Condition
1. Continuous life test:
The part will be subjected to 48 hours of
continuous operation at +45°C with rated
voltage applied.
Evaluation Standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be ±10dB compared to the initial
measurements.
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be within
±10% compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
Reliability Test
Item
Operating (Life Test)
2. Intermittent life test:
A duty cycle of 1 minute on, 1 minute off, a
minimum of 5,000 times at room temp
(+25±2°C) with rated voltage applied.
Test Conditions
Standard Test Condition
Judgement Test Condition
Phone: 800.275.4899
a) Tempurature: +5 ~ +35°C
a) Tempurature: +25 ±2°C
Fax: 503.612.2383
b) Humidity: 45 - 85%
b) Humidity: 60 - 70%
www.cui.com
c) Pressure: 860 - 1060 mbar
c) Pressure: 860 - 1060 mbar
20050 SW 112th Ave.
Tualatin, OR 97062
For more information, please visit the product page.
Part No: CEP-4411AC
Date: 2/06/2007
Unit: mm
Description: piezo audio indicator
Page No: 4 of 4
Packaging
Phone: 800.275.4899
Fax: 503.612.2383
www.cui.com
20050 SW 112th Ave.
Tualatin, OR 97062
Similar pages