PDF Data Sheet Rev. 0

a
FEATURES
PERFORMANCE
25 ns Instruction Cycle Time 40 MIPS Sustained
Performance
Single-Cycle Instruction Execution
Single-Cycle Context Switch
3-Bus Architecture Allows Dual Operand Fetches in
Every Instruction Cycle
Multifunction Instructions
Power-Down Mode Featuring Low CMOS Standby
Power Dissipation with 200 Cycle Recovery from
Power-Down Condition
Low Power Dissipation in Idle Mode
INTEGRATION
ADSP-2100 Family Code Compatible, with Instruction
Set Extensions
20K Bytes of On-Chip RAM, Configured as
4K Words On-Chip Program Memory RAM and
4K Words On-Chip Data Memory RAM
Dual Purpose Program Memory for Both Instruction
and Data Storage
Independent ALU, Multiplier/Accumulator and Barrel
Shifter Computational Units
Two Independent Data Address Generators
Powerful Program Sequencer Provides
Zero Overhead Looping Conditional Instruction
Execution
Programmable 16-Bit Interval Timer with Prescaler
100-Lead LQFP
SYSTEM INTERFACE
16-Bit Internal DMA Port for High Speed Access to
On-Chip Memory (Mode Selectable)
4 MByte Byte Memory Interface for Storage of Data
Tables and Program Overlays (Made Selectable)
8-Bit DMA to Byte Memory for Transparent Program
and Data Memory Transfers (Mode Selectable)
I/O Memory Interface with 2048 Locations Supports
Parallel Peripherals (Mode Selectable)
Programmable Memory Strobe and Separate I/O Memory
Space Permits “Glueless” System Design
(Mode Selectable)
Programmable Wait State Generation
Two Double-Buffered Serial Ports with Companding
Hardware and Automatic Data Buffering
Automatic Booting of On-Chip Program Memory from
Byte-Wide External Memory, e.g., EPROM, or
Through Internal DMA Port
ICE-Port is a trademark of Analog Devices, Inc.
All trademarks are the property of their respective holders.
DSP Microcomputer
ADSP-2184
FUNCTIONAL BLOCK DIAGRAM
POWER-DOWN
CONTROL
DATA ADDRESS
GENERATORS
PROGRAM
SEQUENCER
DAG 1 DAG 2
MEMORY
4K 3 24
4K 3 16
PROGRAM
DATA
MEMORY
MEMORY
FULL MEMORY
MODE
PROGRAMMABLE
I/O
AND
FLAGS
EXTERNAL
ADDRESS
BUS
EXTERNAL
DATA
BUS
PROGRAM MEMORY ADDRESS
DATA MEMORY ADDRESS
BYTE DMA
CONTROLLER
PROGRAM MEMORY DATA
OR
DATA MEMORY DATA
EXTERNAL
DATA
BUS
ARITHMETIC UNITS
ALU
MAC SHIFTER
SERIAL PORTS
SPORT 0 SPORT 1
ADSP-2100 BASE
ARCHITECTURE
TIMER
INTERNAL
DMA
PORT
HOST MODE
Six External Interrupts
13 Programmable Flag Pins Provide Flexible System
Signaling
UART Emulation through Software SPORT Reconfiguration
ICE-Port™ Emulator Interface Supports Debugging
in Final Systems
GENERAL DESCRIPTION
The ADSP-2184 is a single-chip microcomputer optimized for
digital signal processing (DSP) and other high speed numeric
processing applications.
The ADSP-2184 combines the ADSP-2100 family base architecture (three computational units, data address generators and
a program sequencer) with two serial ports, a 16-bit internal
DMA port, a byte DMA port, a programmable timer, Flag I/O,
extensive interrupt capabilities and on-chip program and data
memory.
The ADSP-2184 integrates 20K bytes of on-chip memory configured as 4K words (24-bit) of program RAM and 4K words
(16-bit) of data RAM. Power-down circuitry is also provided to
meet the low power needs of battery operated portable equipment. The ADSP-2184 is available in 100-lead LQFP package.
In addition, the ADSP-2184 supports instructions that include
bit manipulations—bit set, bit clear, bit toggle, bit test— ALU
constants, multiplication instruction (x squared), biased rounding, result free ALU operations, I/O memory transfers, and
global interrupt masking for increased flexibility.
Fabricated in a high speed, double metal, low power, CMOS
process, the ADSP-2184 operates with a 25 ns instruction cycle
time. Every instruction can execute in a single processor cycle.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
ADSP-2184
The EZ-ICE performs a full range of functions, including:
• In-target operation
• Up to 20 breakpoints
• Single-step or full-speed operation
• Registers and memory values can be examined and altered
• PC upload and download functions
• Instruction-level emulation of program booting and execution
• Complete assembly and disassembly of instructions
• C source-level debugging
The ADSP-21xx family DSPs contain a shadow bank register
that is useful for single cycle context switching of the processor.
The ADSP-2184’s flexible architecture and comprehensive
instruction set allow the processor to perform multiple operations in parallel. In one processor cycle the ADSP-2184 can:
• Generate the next program address
• Fetch the next instruction
• Perform one or two data moves
• Update one or two data address pointers
• Perform a computational operation
This takes place while the processor continues to:
• Receive and transmit data through the two serial ports
• Receive or transmit data through the internal DMA port
• Receive or transmit data through the byte DMA port
• Decrement timer
See Designing An EZ-ICE-Compatible Target System in the
ADSP-2100 Family EZ-Tools Manual (ADSP-2181 sections), as
well as the Target Board Connector for EZ-ICE Probe section
of this data sheet, for the exact specifications of the EZ-ICE
target board connector.
Additional Information
This data sheet provides a general overview of ADSP-2184
functionality. For additional information on the architecture and
instruction set of the processor, refer to the ADSP-2100 Family
User’s Manual, Third Edition. For more information about the
development tools, refer to the ADSP-2100 Family Development
Tools Data Sheet.
Development System
The ADSP-2100 Family Development Software, a complete set
of tools for software and hardware system development, supports the ADSP-2184. The System Builder provides a high level
method for defining the architecture of systems under development. The Assembler has an algebraic syntax that is easy to
program and debug. The Linker combines object files into an
executable file. The Simulator provides an interactive instructionlevel simulation with a reconfigurable user interface to display
different portions of the hardware environment. A PROM
Splitter generates PROM programmer compatible files. The
C Compiler, based on the Free Software Foundation’s GNU
C Compiler, generates ADSP-2184 assembly source code.
The source code debugger allows programs to be corrected in
the C environment. The Runtime Library includes over 100
ANSI-standard mathematical and DSP-specific functions.
ARCHITECTURE OVERVIEW
The ADSP-2184 instruction set provides flexible data moves
and multifunction (one or two data moves with a computation)
instructions. Every instruction can be executed in a single processor cycle. The ADSP-2184 assembly language uses an algebraic syntax for ease of coding and readability. A comprehensive
set of development tools supports program development.
POWER-DOWN
CONTROL
The EZ-KIT Lite is a hardware/software kit offering a complete
development environment for the entire ADSP-21xx family: an
ADSP-218x based evaluation board with PC monitor software
plus Assembler, Linker, Simulator and PROM Splitter software.
The ADSP-21xx EZ-KIT Lite is a low cost, easy to use hardware
platform on which you can quickly get started with your DSP software design. The EZ-KIT Lite includes the following features:
• 33 MHz ADSP-2181
• Full 16-bit Stereo Audio I/O with AD1847 SoundPort®
Codec
• RS-232 Interface to PC with Microsoft Windows® 3.1
Control Software
• EZ-ICE® Connector for Emulator Control
• DSP Demo Programs
DATA ADDRESS
GENERATORS
PROGRAM
SEQUENCER
DAG 1 DAG 2
MEMORY
4K 3 24
4K 3 16
PROGRAM
DATA
MEMORY
MEMORY
FULL MEMORY
MODE
PROGRAMMABLE
I/O
AND
FLAGS
EXTERNAL
ADDRESS
BUS
EXTERNAL
DATA
BUS
PROGRAM MEMORY ADDRESS
DATA MEMORY ADDRESS
BYTE DMA
CONTROLLER
PROGRAM MEMORY DATA
OR
DATA MEMORY DATA
EXTERNAL
DATA
BUS
ARITHMETIC UNITS
ALU
MAC SHIFTER
SERIAL PORTS
TIMER
SPORT 0 SPORT 1
ADSP-2100 BASE
ARCHITECTURE
INTERNAL
DMA
PORT
HOST MODE
Figure 1. Block Diagram
Figure 1 is an overall block diagram of the ADSP-2184. The
processor contains three independent computational units: the
ALU, the multiplier/accumulator (MAC) and the shifter. The
computational units process 16-bit data directly and have provisions to support multiprecision computations. The ALU performs a standard set of arithmetic and logic operations; division
primitives are also supported. The MAC performs single-cycle
multiply, multiply/add and multiply/subtract operations with
40 bits of accumulation. The shifter performs logical and arithmetic shifts, normalization, denormalization and derive exponent operations.
The ADSP-218x EZ-ICE Emulator aids in the hardware debugging of an ADSP-2184 system. The emulator consists of hardware, host computer resident software, and the target board
connector. The ADSP-2184 integrates on-chip emulation support with a 14-pin ICE-Port interface. This interface provides a
simpler target board connection that requires fewer mechanical
clearance considerations than other ADSP-2100 Family EZICEs. The ADSP-2184 device need not be removed from the
target system when using the EZ-ICE, nor are any adapters
needed. Due to the small footprint of the EZ-ICE connector,
emulation can be supported in final board designs.
The shifter can be used to efficiently implement numeric
format control including multiword and block floating-point
representations.
SoundPort and EZ-ICE are registered trademarks of Analog Devices, Inc.
Windows is a registered trademark of Microsoft Corporation.
–2–
REV. 0
ADSP-2184
The internal result (R) bus connects the computational units so
the output of any unit may be the input of any unit on the next
cycle.
A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these computational units. The sequencer supports conditional jumps, subroutine calls and returns in a single cycle. With internal loop
counters and loop stacks, the ADSP-2184 executes looped code
with zero overhead; no explicit jump instructions are required to
maintain loops.
Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches from data memory and program memory. Each DAG maintains and updates four address
pointers. Whenever the pointer is used to access data (indirect
addressing), it is post-modified by the value of one of four possible modify registers. A length value may be associated with
each pointer to implement automatic modulo addressing for
circular buffers.
Efficient data transfer is achieved with the use of five internal
buses:
• Program Memory Address (PMA) Bus
• Program Memory Data (PMD) Bus
• Data Memory Address (DMA) Bus
• Data Memory Data (DMD) Bus
• Result (R) Bus
The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip, and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.
Program memory can store both instructions and data, permitting the ADSP-2184 to fetch two operands in a single cycle, one
from program memory and one from data memory. The ADSP2184 can fetch an operand from program memory and the next
instruction in the same cycle.
When configured in host mode, the ADSP-2184 has a 16-bit
Internal DMA port (IDMA port) for connection to external
systems. The IDMA port is made up of 16 data/address pins
and five control pins. The IDMA port provides transparent,
direct access to the DSPs on-chip program and data RAM.
An interface to low cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.
The byte memory and I/O memory space interface supports
slow memories and I/O memory-mapped peripherals with
programmable wait state generation. External devices can
gain control of external buses with bus request/grant signals
(BR, BGH and BG). One execution mode (Go Mode) allows
the ADSP-2184 to continue running from on-chip memory.
Normal execution mode requires the processor to halt while
buses are granted.
The ADSP-2184 can respond to eleven interrupts. There are up
to six external interrupts (one edge-sensitive, two level-sensitive
and three configurable) and seven internal interrupts generated
by the timer, the serial ports (SPORTs), the Byte DMA port
and the power-down circuitry. There is also a master RESET
signal. The two serial ports provide a complete synchronous
serial interface with optional companding in hardware and a
REV. 0
wide variety of framed or frameless data transmit and receive
modes of operation.
Each port can generate an internal programmable serial clock or
accept an external serial clock.
The ADSP-2184 provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, eight
flags are programmable as inputs or outputs, and three flags are
always outputs.
A programmable interval timer generates periodic interrupts. A
16-bit count register (TCOUNT) decrements every n processor
cycle, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).
Serial Ports
The ADSP-2184 incorporates two complete synchronous serial
ports (SPORT0 and SPORT1) for serial communications and
multiprocessor communication.
Here is a brief list of the capabilities of the ADSP-2184 SPORTs.
For additional information on Serial Ports, refer to the ADSP2100 Family User’s Manual, Third Edition.
• SPORTs are bidirectional and have a separate, double-buffered transmit and receive section.
• SPORTs can use an external serial clock or generate their own
serial clock internally.
• SPORTs have independent framing for the receive and transmit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.
• SPORTs support serial data word lengths from 3 to 16 bits
and provide optional A-law and µ-law companding according
to CCITT recommendation G.711.
• SPORT receive and transmit sections can generate unique
interrupts on completing a data word transfer.
• SPORTs can receive and transmit an entire circular buffer of
data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.
• SPORT0 has a multichannel interface to selectively receive
and transmit a 24- or 32-word, time-division multiplexed,
serial bitstream.
• SPORT1 can be configured to have two external interrupts
(IRQ0 and IRQ1) and the Flag In and Flag Out signals. The
internally generated serial clock may still be used in this
configuration.
PIN DESCRIPTIONS
The ADSP-2184 is available in a 100-lead LQFP package. In
order to maintain maximum functionality and reduce package
size and pin count, some serial port, programmable flag, interrupt and external bus pins have dual, multiplexed functionality.
The external bus pins are configured during RESET only, while
serial port pins are software configurable during program execution. Flag and interrupt functionality is retained concurrently
on multiplexed pins. In cases where pin functionality is reconfigurable, the default state is shown in plain text; alternate
functionality is shown in italics.
–3–
ADSP-2184
Common-Mode Pins
Memory Interface Pins
Pin
Name(s)
#
Input/
of
OutPins put
Function
RESET
BR
BG
BGH
DMS
PMS
IOMS
BMS
CMS
RD
WR
IRQ2/
1
1
1
1
1
1
1
1
1
1
1
1
PF7
IRQL0/
PF5
IRQL1/
PF6
IRQE/
PF4
PF3
Mode C/
1
1
1
1
1
PF2
Mode B/
1
I
I/O
1
PF0
CLKIN, XTAL
CLKOUT
SPORT0
SPORT1/
IRQ1:0
FI, FO
PWD
PWDACK
FL0, FL1, FL2
VDD and GND
EZ-Port
I/O
I
I/O
I
I/O
I
I/O
I/O
I
I/O
PF1
Mode A/
I
I
O
O
O
O
O
O
O
O
O
I
I
I/O
2
1
5
5
I
O
I/O
I/O
1
1
3
16
9
I
O
O
I
I/O
The ADSP-2184 processor can be used in one of two modes:
Full Memory Mode, which allows BDMA operation with full
external overlay memory and I/O capability, or Host Mode,
which allows IDMA operation with limited external addressing
capabilities. The operating mode is determined by the state of
the Mode C pin during RESET and cannot be changed while
the processor is running.
Processor Reset Input
Bus Request Input
Bus Grant Output
Bus Grant Hung Output
Data Memory Select Output
Program Memory Select Output
I/O Memory Select Output
Byte Memory Select Output
Combined Memory Select Output
Memory Read Enable Output
Memory Write Enable Output
Edge- or Level-Sensitive
Interrupt Request1
Programmable I/O Pin
Level-Sensitive Interrupt Requests1
Programmable I/O Pin
Level-Sensitive Interrupt Requests1
Programmable I/O Pin
Edge-Sensitive Interrupt Requests1
Programmable I/O Pin
Programmable I/O Pin
Mode Select Input—Checked
only During RESET
Programmable I/O Pin During
Normal Operation
Mode Select Input—Checked
only During RESET
Programmable I/O Pin During
Normal Operation
Mode Select Input—Checked
only During RESET
Programmable I/O Pin During
Normal Operation
Clock or Quartz Crystal Input
Processor Clock Output
Serial Port I/O Pins
Serial Port I/O Pins
Edge- or Level-Sensitive Interrupts,
Flag In, Flag Out 2
Power-Down Control Input
Power-Down Control Output
Output Flags
Power and Ground
For Emulation Use
Full Memory Mode Pins (Mode C = 0)
Pin Name
#
of
Pins
Input/
Output
A13:0
14
O
D23:0
24
I/O
Function
Address Output Pins for Program, Data, Byte and I/O Spaces
Data I/O Pins for Program,
Data, Byte and I/O Spaces
(8 MSBs Are Also Used as
Byte Memory Addresses)
Host Mode Pins (Mode C = 1)
Pin Name
#
of
Pins
Input/
Output
IAD15:0
A0
16
1
I/O
O
D23:8
16
I/O
IWR
IRD
IAL
IS
IACK
1
1
1
1
1
I
I
I
I
O
Function
IDMA Port Address/Data Bus
Address Pin for External I/O,
Program, Data, or Byte Access
Data I/O Pins for Program,
Data Byte and I/O Spaces
IDMA Write Enable
IDMA Read Enable
IDMA Address Latch Pin
IDMA Select
IDMA Port Acknowledge
In Host Mode, external peripheral addresses can be decoded using the A0,
BMS, CMS, PMS, DMS, and IOMS signals.
Setting Memory Mode
Memory Mode selection for the ADSP-2184 is made during
chip reset through the use of the Mode C pin. This pin is multiplexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are passive and active.
Passive configuration involves the use a pull-up or pull-down
resistor connected to the Mode C pin. To minimize power
consumption, or if the PF2 pin is to be used as an output in the
DSP application, a weak pull-up or pull-down, on the order of
100 kΩ, can be used. This value should be sufficient to pull the
pin to the desired level and still allow the pin to operate as a
programmable flag output without undue strain on the processor’s
output driver. For minimum power consumption during
power-down, reconfigure PF2 to be an input, as the pull-up or
pull-down will hold the pin in a known state, and will not switch.
NOTES
1
Interrupt/Flag pins retain both functions concurrently. If IMASK is set to
enable the corresponding interrupts, the DSP will vector to the appropriate
interrupt vector address when the pin is asserted, either by external devices or
set as a programmable flag.
2
SPORT configuration determined by the DSP System Control Register. Software configurable.
Active configuration involves the use of a three-stateable external driver connected to the Mode C pin. A driver’s output enable should be connected to the DSP’s RESET signal such that
it only drives the PF2 pin when RESET is active (low). After
RESET is deasserted, the driver should three-state, thus allowing full use of the PF2 pin as either an input or output.
–4–
REV. 0
ADSP-2184
To minimize power consumption during power-down, configure
the programmable flag as an output when connected to a threestated buffer. This ensures that the pin will be held at a constant
level and not oscillate should the three-state driver’s level hover
around the logic switching point.
The IFC register is a write-only register used to force and clear
interrupts.
Interrupts
The following instructions allow global enable or disable servicing of the interrupts (including power-down), regardless of the
state of IMASK. Disabling the interrupts does not affect serial
port autobuffering or DMA.
The interrupt controller allows the processor to respond to the
eleven possible interrupts and reset with minimum overhead.
The ADSP-2184 provides four dedicated external interrupt
input pins, IRQ2, IRQL0, IRQL1 and IRQE (shared with the
PF7:4 pins). In addition, SPORT1 may be reconfigured for
IRQ0, IRQ1, FLAG_IN and FLAG_OUT, for a total of six
external interrupts. The ADSP-2184 also supports internal
interrupts from the timer, the byte DMA port, the two serial
ports, software and the power-down control circuit. The interrupt levels are internally prioritized and individually maskable
(except power-down and RESET). The IRQ2, IRQ0 and IRQ1
input pins can be programmed to be either level- or edge-sensitive.
IRQL0 and IRQL1 are level-sensitive and IRQE is edge-sensitive.
The priorities and vector addresses of all interrupts are shown in
Table I.
Table I. Interrupt Priority & Interrupt Vector Addresses
Source Of Interrupt
Interrupt Vector Address (Hex)
Reset (or Power-Up with
PUCR = 1)
Power-Down (Nonmaskable)
IRQ2
IRQL1
IRQL0
SPORT0 Transmit
SPORT0 Receive
IRQE
BDMA Interrupt
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
0000 (Highest Priority)
002C
0004
0008
000C
0010
0014
0018
001C
0020
0024
0028 (Lowest Priority)
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATION
The ADSP-2184 has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
• Power-Down
• Idle
• Slow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
Interrupt routines can either be nested, with higher priority
interrupts taking precedence, or processed sequentially. Interrupts can be masked or unmasked with the IMASK register.
Individual interrupt requests are logically ANDed with the bits
in IMASK; the highest priority unmasked interrupt is then
selected. The power-down interrupt is nonmaskable.
The ADSP-2184 masks all interrupts for one instruction cycle
following the execution of an instruction that modifies the
IMASK register. This does not affect serial port autobuffering
or DMA transfers.
The interrupt control register, ICNTL, controls interrupt nesting and defines the IRQ0, IRQ1 and IRQ2 external interrupts to
be either edge- or level-sensitive. The IRQE pin is an external
edge-sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level-sensitive interrupts.
REV. 0
On-chip stacks preserve the processor status and are automatically maintained during interrupt handling. The stacks are twelve
levels deep to allow interrupt, loop and subroutine nesting.
The ADSP-2184 processor has a low power feature that lets the
processor enter a very low power dormant state through hardware or software control. Following is a brief list of power-down
features. Refer to the ADSP-2100 Family User’s Manual, Third
Edition, “System Interface” chapter, for detailed information
about the power-down feature.
• Quick recovery from power-down. The processor begins
executing instructions in as few as 200 CLKIN cycles.
• Support for an externally generated TTL or CMOS processor clock. The external clock can continue running during
power-down without affecting the lowest power rating and
200 CLKIN cycle recovery.
• Support for crystal operation includes disabling the oscillator
to save power (the processor automatically waits approximately 4096 CLKIN cycles for the crystal oscillator to start
or stabilize), and letting the oscillator run to allow 200 CLKIN
cycle start-up.
• Power-down is initiated by either the power-down pin (PWD)
or the software power-down force bit.
• Interrupt support allows an unlimited number of instructions
to be executed before optionally powering down. The powerdown interrupt also can be used as a nonmaskable, edgesensitive interrupt.
• Context clear/save control allows the processor to continue
where it left off or start with a clean context when leaving the
power-down state.
• The RESET pin also can be used to terminate power-down.
• Power-down acknowledge pin indicates when the processor
has entered power-down.
–5–
ADSP-2184
Idle
FULL MEMORY MODE
When the ADSP-2184 is in the Idle Mode, the processor waits
indefinitely in a low power state until an interrupt occurs. When
an unmasked interrupt occurs, it is serviced; execution then
continues with the instruction following the IDLE instruction.
In Idle mode IDMA, BDMA and autobuffer cycle steals still
occur.
ADSP-2184
CLKIN
1/2x CLOCK
OR
CRYSTAL
14
ADDR13-0
XTAL
FL0-2
PF3
D23-16
24
A0-A21
BYTE
MEMORY
D15-8
DATA
DATA23-0
IRQ2/PF7
IRQE/PF4
IRQL0/PF5
IRQL1/PF6
Slow Idle
A13-0
BMS
CS
A10-0
ADDR
D23-8
MODE C/PF2
MODE B/PF1
MODE A/PF0
The IDLE instruction is enhanced on the ADSP-2184 to let the
processor’s internal clock signal be slowed, further reducing
power consumption. The reduced clock frequency, a programmable fraction of the normal clock rate, is specified by a selectable divisor given in the IDLE instruction. The format of the
instruction is
DATA
IOMS
CS
SERIAL
DEVICE
SERIAL
DEVICE
SCLK0
RFS0
TFS0
DT0
DR0
IDLE (n);
ADDR
OVERLAY
MEMORY
D23-0
DATA
CS
PMS
DMS
CMS
SPORT0
where n = 16, 32, 64 or 128. This instruction keeps the processor fully functional, but operating at the slower clock rate. While
it is in this state, the processor’s other internal clock signals,
such as SCLK, CLKOUT and timer clock, are reduced by the
same ratio. The default form of the instruction, when no clock
divisor is given, is the standard IDLE instruction.
2048 LOCATIONS
A13-0
SPORT1
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
I/O SPACE
(PERIPHERALS)
TWO 8K
PM SEGMENTS
TWO 8K
DM SEGMENTS
BR
BG
BGH
PWD
PWDACK
HOST MEMORY MODE
ADSP-2184
When the IDLE (n) instruction is used, it effectively slows down
the processor’s internal clock and thus its response time to incoming interrupts. The one-cycle response time of the standard
idle state is increased by n, the clock divisor. When an enabled
interrupt is received, the ADSP-2184 will remain in the idle
state for up to a maximum of n processor cycles (n = 16, 32, 64
or 128) before resuming normal operation.
CLKIN
1/2x CLOCK
OR
CRYSTAL
ADDR0
1
XTAL
FL0-2
PF3
IRQ2/PF7
IRQE/PF4
IRQL0/PF5
IRQL1/PF6
16
DATA23-8
BMS
MODE C/PF2
MODE B/PF1
MODE A/PF0
When the IDLE (n) instruction is used in systems that have an
externally generated serial clock (SCLK), the serial clock rate
may be faster than the processor’s reduced internal clock rate.
Under these conditions, interrupts must not be generated at a
faster rate than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of n
processor cycles).
SPORT1
SERIAL
DEVICE
SCLK1
RFS1 OR IRQ0
TFS1 OR IRQ1
DT1 OR FO
DR1 OR FI
SERIAL
DEVICE
SCLK0
RFS0
TFS0
DT0
DR0
SPORT0
IDMA PORT
SYSTEM INTERFACE
SYSTEM
INTERFACE
OR
mCONTROLLER
Figure 2 shows typical basic system configurations with the
ADSP-2184, two serial devices, a byte-wide EPROM and optional
external program and data overlay memories (mode selectable).
Programmable wait state generation allows the processor to
connect easily to slow peripheral devices. The ADSP-2184 also
provides four external interrupts and two serial ports or six
external interrupts and one serial port. Host Memory Mode
allows access to the full external data bus, but limits addressing
to a single address bit (A0). Additional system peripherals can
be added in this mode through the use of external hardware to
generate and latch address signals.
16
IRD/D6
IWR/D7
IS/D4
IAL/D5
IACK/D3
IAD15-0
IOMS
PMS
DMS
CMS
BR
BG
BGH
PWD
PWDACK
Figure 2. Basic System Configuration
–6–
REV. 0
ADSP-2184
Clock Signals
The ADSP-2184 can be clocked by either a crystal or a TTLcompatible clock signal.
The CLKIN input cannot be halted, changed during operation
or operated below the specified frequency during normal operation. The only exception is while the processor is in the powerdown state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual, Third Edition, for detailed
information on this power-down feature.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When RESET is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes. In an EZ-ICE-compatible system RESET and
ERESET have the same functionality. For complete information, see Designing an EZ-ICE-Compatible Systems section.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is connected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
MEMORY ARCHITECTURE
The ADSP-2184 uses an input clock with a frequency equal to
half the instruction rate; a 20.00 MHz input clock yields a 25 ns
processor cycle (which is equivalent to 40 MHz). Normally,
instructions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.
Program Memory (Full Memory Mode) is a 24-bit-wide space
for storing both instruction opcodes and data. The ADSP-2184
has 4K words of Program Memory RAM on chip, and the capability of accessing up to two 8K external memory overlay spaces using
the external data bus. Both an instruction opcode and a data value
can be read from on-chip program memory in a single cycle.
Because the ADSP-2184 includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be connected across the CLKIN and XTAL pins, with two capacitors
connected as shown in Figure 3. Capacitor values are dependent
on crystal type and should be specified by the crystal manufacturer. A parallel-resonant, fundamental frequency, microprocessor-grade crystal should be used.
Data Memory (Full Memory Mode) is a 16-bit-wide space
used for the storage of data variables and for memory-mapped
control registers. The ADSP-2184 has 4K words on Data
Memory RAM on chip. Support also exists for up to two 8K
external memory overlay spaces through the external data bus.
A clock output (CLKOUT) signal is generated by the processor at the processor’s cycle rate. This can be enabled and
disabled by the CLKODIS bit in the SPORT0 Autobuffer
Control Register.
CLKIN
XTAL
CLKOUT
DSP
The ADSP-2184 provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory and I/O.
Byte Memory (Full Memory Mode) provides access to an
8-bit wide memory space through the Byte DMA (BDMA) port.
The Byte Memory interface provides access to 4 MBytes of
memory by utilizing eight data lines as additional address lines.
This gives the BDMA Port an effective 22-bit address range. On
power-up, the DSP can automatically load bootstrap code from
byte memory.
I/O Space (Full Memory Mode) allows access to 2048 locations of 16-bit-wide data. It is intended to be used to communicate with parallel peripheral devices such as data converters and
external registers or latches.
Program Memory
Figure 3. External Crystal Connections
Reset
The RESET signal initiates a master reset of the ADSP-2184.
The RESET signal must be asserted during the power-up
sequence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The ADSP-2184 contains 4K × 24 of on-chip program RAM.
The on-chip program memory is designed to allow up to two
accesses each cycle so that all operations can complete in a
single cycle. In addition, the ADSP-2184 allows the use of 8K
external memory overlays.
The program memory space organization is controlled by the
Mode B pin and the PMOVLAY register. Normally, the ADSP2184 is configured with Mode B = 0 and program memory
organized as shown in Figure 4.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid VDD is
applied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked, but does
not include the crystal oscillator start-up time. During this
power-up sequence the RESET signal should be held low. On
any subsequent resets, the RESET signal must meet the minimum pulsewidth specification, tRSP .
PROGRAM MEMORY
The RESET input contains some hysteresis; however, if you use
an RC circuit is used to generate your RESET signal, the use of
an external Schmidt trigger is recommended.
4K INTERNAL
REV. 0
ADDRESS
0x3FFF
EXTERNAL 8K
(PMOVLAY = 1 or 2,
MODE B = 0)
0x2000
0x1FFF
RESERVED
MEMORY
RANGE
0x1000
0x0FFF
0x0000
Figure 4. Program Memory (Mode B = 0)
–7–
ADSP-2184
When PMOVLAY is set to 1 or 2, external accesses occur at
addresses 0x2000 through 0x3FFF. The external address is
generated as shown in Table II.
There are 4K words of memory accessible internally when the
DMOVLAY register is set to 0. When DMOVLAY is set to 1 or
2, external accesses occur at addresses 0x0000 through 0x1FFF.
The external address is generated as shown in Table III.
Table II.
PMOVLAY Memory
A13
0
1
Internal
External
Overlay 1
2
External
Overlay 2
Not Applicable Not Applicable
13 LSBs of Address
0
Between 0x2000
and 0x3FFF
13 LSBs of Address
1
Between 0x2000
and 0x3FFF
Table III.
A12:0
DMOVLAY Memory
A13
0
1
Internal
External
Overlay 1
2
External
Overlay 2
Not Applicable Not Applicable
13 LSBs of Address
0
Between 0x0000
and 0x1FFF
13 LSBs of Address
1
Between 0x0000
and 0x1FFF
NOTE: Addresses 0x2000 through 0x3FFF should not be accessed when
PMOVLAY = 0.
This organization allows for two external 8K overlays using only
the normal 14 address bits. All internal accesses complete in one
cycle. Accesses to external memory are timed using the wait
states specified by the DWAIT register.
This organization provides for two external 8K overlay segments
using only the normal 14 address bits, which allows for simple
program overlays using one of the two external segments in
place of the on-chip memory. Care must be taken in using this
overlay space in that the processor core (i.e., the sequencer)
does not take into account the PMOVLAY register value. For
example, if a loop operation is occurring on one of the external
overlays and the program changes to another external overlay or
internal memory, an incorrect loop operation could occur. In
addition, care must be taken in interrupt service routines as the
overlay registers are not automatically saved and restored on the
processor mode stack.
I/O Space (Full Memory Mode)
The ADSP-2184 supports an additional external memory space
called I/O space. This space is designed to support simple connections to peripherals or to bus interface ASIC data registers.
I/O space supports 2048 locations. The lower eleven bits of the
external address bus are used; the upper three bits are undefined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait state
registers, IOWAIT0-3, that specify up to seven wait states to be
automatically generated for each of four regions. The wait states
act on address ranges as shown in Table IV.
When Mode B = 1, booting is disabled and overlay memory is
disabled the 4K internal PM cannot be accessed with MODE
B = 1. Figure 5 shows the memory map in this configuration.
PROGRAM MEMORY
A12:0
ADDRESS
0x3FFF
Table IV.
RESERVED
0x2000
0x1FFF
8K EXTERNAL
0x0000
Figure 5. Program Memory (Mode B = 1)
0x000–0x1FF
0x200–0x3FF
0x400–0x5FF
0x600–0x7FF
IOWAIT0
IOWAIT1
IOWAIT2
IOWAIT3
The ADSP-2184 has a programmable memory select signal that
is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory select
signals (PMS, DMS, BMS, IOMS), but can combine their
functionality.
The ADSP-2184 has 4K 16-bit words of internal data memory. In
addition, the ADSP-2184 allows the use of 8K external memory
overlays. Figure 6 shows the organization of the data memory.
ADDRESS
0x3FFF
32 MEMORY–
MAPPED REGISTERS
Each bit in the CMSSEL register, when set, causes the CMS
signal to be asserted when the selected memory select is asserted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory and use either DMS or PMS as the additional
address bit.
0x3FEO
4064
RESERVED
WORDS
Wait State Register
Composite Memory Select (CMS)
Data Memory
DATA MEMORY
Address Range
0x3FDF
0x3000
0x2FFF
INTERNAL
4K WORDS
0x2000
0x1FFF
The CMS pin functions as the other memory select signals, with
the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits, except the BMS
bit, default to 1 at reset.
EXTERNAL 8K
(DMOVLAY = 1, 2)
0x0000
Figure 6. Data Memory
–8–
REV. 0
ADSP-2184
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space
consists of 256 pages, each of which is 16K × 8.
The byte memory space on the ADSP-2184 supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses
data bits 23:16 and address bits 13:0 to create a 22-bit address.
This allows up to a 4 meg × 8 (32 megabit) ROM or RAM to be
used without glue logic. All byte memory accesses are timed by
the BMWAIT register.
Byte Memory DMA (BDMA, Full Memory Mode)
The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.
The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number
of 8-bit accesses is done from the byte memory space to build
the word size selected. Table V shows the data formats supported by the BDMA circuit.
Table V.
BTYPE
Internal
Memory Space
Word Size
Alignment
00
01
10
11
Program Memory
Data Memory
Data Memory
Data Memory
24
16
8
8
Full Word
Full Word
MSBs
LSBs
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address for
the on-chip memory involved with the transfer. The 14-bit BEAD
register specifies the starting address for the external byte memory
space. The 8-bit BMPAGE register specifies the starting page for
the external byte memory space. The BDIR register field selects
the direction of the transfer. The 14-bit BWCOUNT register
specifies the number of DSP words to transfer and initiates the
BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is generated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory, regardless of the values of
Mode B, PMOVLAY or DMOVLAY.
REV. 0
When the BWCOUNT register is written with a nonzero value,
the BDMA circuit starts executing byte memory accesses with
wait states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
create a destination word, it is transferred to or from on-chip
memory. The transfer takes one DSP cycle. DSP accesses to
external memory have priority over BDMA byte memory
accesses.
The BDMA Context Reset bit (BCR) controls whether the
processor is held off while the BDMA accesses are occurring.
Setting the BCR bit to 0 allows the processor to continue operations. Setting the BCR bit to 1 causes the processor to stop
execution while the BDMA accesses are occurring, to clear the
context of the processor and start execution at address 0 when
the BDMA accesses have completed.
Internal Memory DMA Port (IDMA Port; Host Memory Mode)
The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2184. The port is used to
access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot, however, be used to write to the DSP’s memorymapped control registers.
The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is completely asynchronous and can be written to while the ADSP2184 is operating at full speed.
The DSP memory address is latched and then automatically
incremented after each IDMA transaction. An external device
can therefore access a block of sequentially addressed memory
by specifying only the starting address of the block. This increases throughput as the address does not have to be sent for
each memory access.
IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a 14-bit
address and 1-bit destination type can be driven onto the bus by
an external device. The address specifies an on-chip memory
location, the destination type specifies whether it is a DM or
PM access. The falling edge of the IDMA address latch signal
(IAL) or the missing edge of the IDMA select signal (IS) latches
this value into the IDMAA register.
Once the address is stored, data can then either be read from or
written to the ADSP-2184’s on-chip memory. Asserting the
select line (IS) and the appropriate read or write line (IRD and
IWR respectively) signals the ADSP-2184 that a particular
transaction is required. In either case, there is a one-processorcycle delay for synchronization. The memory access consumes
one additional processor cycle.
Once an access has occurred, the latched address is automatically incremented and another access can occur.
Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation.
–9–
ADSP-2184
Bootstrap Loading (Booting)
The ADSP-2184 has two mechanisms to allow automatic loading of the internal program memory after reset. The method for
booting is controlled by the Mode A, B and C configuration bits
as shown in Table VI. These four states can be compressed into
two-state bits by allowing an IDMA boot with Mode C = 1.
However, three bits are used to ensure future compatibility with
parts containing internal program memory ROM.
BDMA Booting
When the MODE pins specify BDMA booting, the ADSP-2184
initiates a BDMA boot sequence when RESET is released.
Table VI. Boot Summary Table
0
0
IDMA Port Booting
The ADSP-2184 can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2184 boots from the IDMA port. The IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
Bus Request and Bus Grant
The ADSP-2184 can relinquish control of the data and address
buses to an external device. When the external device requires
access to memory, it asserts the bus request (BR) signal. If the
ADSP-2184 is not performing an external memory access, it
responds to the active BR input in the following processor cycle
by:
MODE C MODE B MODE A Booting Method
0
The IDLE instruction can also be used to allow the processor to
hold off execution while booting continues through the BDMA
interface. For BDMA accesses while in Host Mode, the addresses to boot memory must be constructed externally to the
ADSP-2184. The only memory address bit provided by the
processor is A0.
BDMA feature is used to load
the first 32 program memory
words from the byte memory
space. Program execution is
held off until all 32 words have
been loaded. Chip is configured in Full Memory Mode.
• Three-stating the data and address buses and the PMS, DMS,
BMS, CMS, IOMS, RD, WR output drivers,
• Asserting the bus grant (BG) signal, and
0
1
1
1
0
0
0
0
1
No Automatic boot operations
occur. Program execution
starts at external memory
location 0. Chip is configured
in Full Memory Mode. BDMA
can still be used but the processor does not automatically
use or wait for these operations.
BDMA feature is used to load
the first 32 program memory
words from the byte memory
space. Program execution is
held off until all 32 words have
been loaded. Chip is configured in Host Mode. Additional
interface hardware is required.
IDMA feature is used to load
any internal memory as desired. Program execution is
held off until internal program
memory location 0 is written
to. Chip is configured in Host
Mode.
• Halting program execution.
If Go Mode is enabled, the ADSP-2184 will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2184 is performing an external memory access
when the external device asserts the BR signal, it will not threestate the memory interfaces or assert the BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
When the BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when RESET is active.
The BGH pin is asserted when the ADSP-2184 is ready to
execute an instruction but is stopped because the external bus is
already granted to another device. The other device can release
the bus by deasserting bus request. Once the bus is released, the
ADSP-2184 deasserts BG and BGH and executes the external
memory access.
The BDMA interface is set up during reset to the following defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD and BEAD registers are set to 0; the BTYPE register is
set to 0 to specify program memory 24-bit words; and the
BWCOUNT register is set to 32. This causes 32 words of onchip program memory to be loaded from byte memory. These
32 words are used to set up the BDMA to load in the remaining
program code. The BCR bit is also set to 1, which causes program execution to be held off until all 32 words are loaded into
on-chip program memory. Execution then begins at address 0.
Flag I/O Pins
The ADSP-2184 has eight general purpose programmable input/
output flag pins. They are controlled by two memory mapped
registers. The PFTYPE register determines the direction,
1 = output and 0 = input. The PFDATA register is used to read
and write the values on the pins. Data being read from a pin
configured as an input is synchronized to the ADSP-2184’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
–10–
REV. 0
ADSP-2184
In addition to the programmable flags, the ADSP-2184 has five
fixed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1 and
FL2. FL0-FL2 are dedicated output flags. FLAG_IN and
FLAG_OUT are available as an alternate configuration of
SPORT1.
Note: Pins PF0, PF1 and PF2 are also used for device configuration during reset.
ERESET
RESET
ADSP-2184
INSTRUCTION SET DESCRIPTION
The ADSP-2184 assembly language instruction set has an algebraic syntax that was designed for ease of coding and readability. The assembly language, which takes full advantage of the
processor’s unique architecture, offers the following benefits:
• The algebraic syntax eliminates the need to remember cryptic
assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.
• Every instruction assembles into a single, 24-bit word that
can execute in a single instruction cycle.
• The syntax is a superset ADSP-2100 Family assembly language and is completely source and object code compatible
with other family members. Programs may need to be relocated to utilize on-chip memory and conform to the ADSP2184’s interrupt vector and reset vector map.
• Sixteen condition codes are available. For conditional jump,
call, return or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.
• Multifunction instructions allow parallel execution of an
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2184 has on-chip emulation support and an
ICE-Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE’s in-circuit probe, a 14-pin plug.
Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface.
If using a passive method of maintaining mode information (as
discussed in Setting Memory Modes), it does not matter that
the mode information is latched by an emulator reset. However,
if using the RESET pin as a method of setting the value of the
mode pins, the effects of an emulator reset must be taken into
consideration.
1kV
MODE A/PFO
PROGRAMMABLE I/O
Figure 7.
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
The ICE-Port interface consists of the following ADSP-2184
pins:
EBR
EMS
ELIN
ERESET
ECLK
EE
These ADSP-2184 pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function
except during emulation, and do not require pull-up or
pull-down resistors. The traces for these signals between the
ADSP-2184 and the connector must be kept as short as possible, no longer than three inches.
The following pins are also used by the EZ-ICE:
BR
RESET
BG
GND
The EZ-ICE uses the EE (emulator enable) signal to take control of the ADSP-2184 in the target system. This causes the
processor to use its ERESET, EBR and EBG pins instead of
the RESET, BR and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 8. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
One method of ensuring that the values located on the mode
pins is the one that is desired to construct a circuit like the one
shown in Figure 7. This circuit will force the value located on
the Mode A pin to Logic Low, regardless if it latched via the
RESET or ERESET pin.
REV. 0
EBG
EINT
ELOUT
–11–
ADSP-2184
1
2
3
4
GND
EBG
BG
BR
5
6
7
8
EBR
EINT
KEY (NO PIN)
ELIN
9
10
11
12
13
14
Restriction: All memory strobe signals on the ADSP-2184 (RD,
WR, PMS, DMS, BMS, CMS and IOMS) used in your target
system must have 10 kΩ pull-up resistors connected when the
EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
ECLK
ELOUT
EE
RESET
Note: If your target does not meet the worst case chip specifications for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depending on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statistically vary in switching characteristics and timing requirements
within published limits.
EMS
ERESET
TOP VIEW
Target System Interface Signals
Figure 8. Target Board Connector for EZ-ICE
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
The 14-pin, 2-row pin strip header is keyed at the Pin 7 location—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spacing should be 0.1 × 0.1 inches. The pin strip header must have
at least 0.15-inch clearance on all sides to accept the EZ-ICE
probe plug. Pin strip headers are available from vendors such as
3M, McKenzie and Samtec.
• EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the RESET
signal.
Target Memory Interface
• EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the BR signal.
For your target system to be compatible with the EZ-ICE emulator, it must comply with the memory interface guidelines listed
below.
• EZ-ICE emulation ignores RESET and BR when singlestepping.
PM, DM, BM, IOM, and CM
• EZ-ICE emulation ignores RESET and BR when in Emulator
Space (DSP halted).
Design a Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM) and Composite Memory
(CM) external interfaces to comply with worst case device timing requirements and switching characteristics as specified in
this DSP’s data sheet. The performance of the EZ-ICE may approach published worst case specifications for some memory
access timing requirements and switching characteristics.
• EZ-ICE emulation ignores the state of target BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (BG) is asserted
by the EZ-ICE board’s DSP.
–12–
REV. 0
ADSP-2184
SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
B Grade
Parameter
Min
Max
Unit
VDD
TAMB
4.5
–40
5.5
+85
V
°C
ELECTRICAL CHARACTERISTICS
Parameter
VIH
VIH
VIL
VOH
1, 2
Hi-Level Input Voltage
Hi-Level CLKIN Voltage
Lo-Level Input Voltage1, 3
Hi-Level Output Voltage1, 4, 5
VOL
Lo-Level Output Voltage1, 4, 5
IIH
Hi-Level Input Current3
IIL
Lo-Level Input Current3
IOZH
Three-State Leakage Current7
IOZL
Three-State Leakage Current7
IDD
IDD
Supply Current (Idle)9
Supply Current (Dynamic)10, 11
CI
Input Pin Capacitance3, 6, 12
CO
Output Pin Capacitance6, 7, 12, 13
Test Conditions
Min
@ VDD = max
@ VDD = max
@ VDD = min
@ VDD = min
IOH = –0.5 mA
@ VDD = min
IOH = –100 µA6
@ VDD = min
IOL = 2 mA
@ VDD = max
VIN = VDD max
@ VDD = max
VIN = 0 V
@ VDD = max
VIN = VDD max8
@ VDD = max
VIN = 0 V8, tCK = 25 ns
@ VDD = 5.0
@ VDD = 5.0
TAMB = +25°C
tCK = 25 ns
@ VIN = 2.5 V,
fIN = 1.0 MHz,
TAMB = +25°C
@ VIN = 2.5 V,
fIN = 1.0 MHz,
TAMB = +25°C
2.0
2.2
B Grade
Typ
Max
Unit
0.8
V
V
V
2.4
V
VDD – 0.3
V
0.4
V
10
µA
10
µA
10
µA
10
14
µA
mA
60
mA
8
pF
8
pF
NOTES
1
Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.
2
Input only pins: RESET, BR, DR0, DR1, PWD.
3
Input only pins: CLKIN, RESET, BR, DR0, DR1, PWD.
4
Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2-0, BGH.
5
Although specified for TTL outputs, all ADSP-2184 outputs are CMOS-compatible and will drive to V DD and GND, assuming no dc loads.
6
Guaranteed but not tested.
7
Three-statable pins: A0–A13, D0–D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RSF1, PF0–PF7.
8
0 V on BR.
9
Idle refers to ADSP-2184 state of operation during execution of IDLE instruction. Deasserted pins are driven to either V DD or GND.
10
IDD measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are type 2
and type 6, and 20% are idle instructions.
11
VIN = 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.
12
Applies to LQFP package type.
13
Output pin capacitance is the capacitive load for any three-stated output pin.
Specifications subject to change without notice.
REV. 0
–13–
ADSP-2184
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Output Voltage Swing . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range (Ambient) . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 sec) LQFP . . . . . . . . . . . . . . . . +280°C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only; functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2184 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
TIMING PARAMETERS
GENERAL NOTES
MEMORY TIMING SPECIFICATIONS
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
The table below shows common memory device specifications
and the corresponding ADSP-2184 timing parameters, for your
convenience.
TIMING NOTES
Switching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the processor operates correctly with other devices.
Memory
Device
Specification
ADSP-2184 Timing
Timing
Parameter
Parameter Definition
Address Setup to
Write Start
Address Setup to
Write End
Address Hold Time
tASW
tAW
Data Setup Time
tDW
tWRA
Data Hold Time
tDH
OE to Data Valid
tRDD
Address Access Time tAA
A0–A13, xMS Setup
before WR Low
A0–A13, xMS Setup
before WR Deasserted
A0–A13, xMS Hold before
WR Low
Data Setup before WR
High
Data Hold after WR High
RD Low to Data Valid
A0–A13, xMS to Data
Valid
xMS = PMS, DMS, BMS, CMS, IOMS.
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS
tCK is defined as 0.5 tCKI. The ADSP-2184 uses an input clock
with a frequency equal to half the instruction rate: a 20 MHz
input clock (which is equivalent to 50 ns) yields a 25 ns processor cycle (equivalent to 40 MHz). tCK values within the range of
0.5 tCKI period should be substituted for all relevant timing parameters to obtain the specification value.
Example: tCKH = 0.5 tCK – 7 ns = 0.5 (25 ns) – 7 ns = 5.5 ns
–14–
REV. 0
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
Timing Requirements:
CLKIN Period
tCKI
tCKIL
CLKIN Width Low
tCKIH
CLKIN Width High
50
20
20
150
ns
ns
ns
Switching Characteristics:
tCKL
CLKOUT Width Low
tCKH
CLKOUT Width High
tCKOH
CLKIN High to CLKOUT High
0.5 tCK – 7
0.5 tCK – 7
0
Clock Signals and Reset
20
ns
ns
ns
Control Signals
Timing Requirements:
tRSP
RESET Width Low1
tMS
Mode Setup before RESET High
tMH
Mode Setup after RESET High
5 tCK
2
5
ns
ns
ns
NOTES
1Applies after power-up sequence is complete. Internal phase lock loop requires no more than 2000 CLKIN cycles assuming stable CLKIN (not including crystal
oscillator start-up time).
tCKI
tCKIH
CLKIN
tCKIL
tCKOH
tCKH
CLKOUT
tCKL
PF(2:0)*
tMS
tMH
RESET
*PF2 IS MODE C, PF1 IS MODE B, PF0 IS MODE A
Figure 9. Clock Signals
REV. 0
–15–
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
Interrupts and Flag
Timing Requirements:
tIFS
IRQx, FI, or PFx Setup before CLKOUT Low1, 2, 3, 4
tIFH
IRQx, FI, or PFx Hold after CLKOUT High1, 2, 3, 4
0.25 tCK + 15
0.25 tCK
Switching Characteristics:
tFOH
Flag Output Hold after CLKOUT Low5
tFOD
Flag Output Delay from CLKOUT Low5
ns
ns
0.25 tCK – 7
0.5 tCK + 6
ns
ns
NOTES
1 If IRQx and FI inputs meet t
IFS and tIFH setup/hold requirements, they will be recognized during the current clock cycle; otherwise the signals will be recognized on the
following cycle. (Refer to “Interrupt Controller Operation” in the Program Control chapter of the ADSP-2100 Family User’s Manual, Third Edition, for further information
on interrupt servicing.)
2 Edge-sensitive interrupts require pulsewidths greater than 10 ns; level-sensitive interrupts must be held low until serviced.
3 IRQx = IRQ0, IRQ1, IRQ2, IRQL0, IRQL1, IRQE.
4 PFx = PF0, PF1, PF2, PF3, PF4, PF5, PF6, PF7.
5 Flag outputs = PFx, FL0, FL1, FL2, Flag_out.
tFOD
CLKOUT
tFOH
FLAG
OUTPUTS
tIFH
IRQx
FI
PFx
tIFS
Figure 10.␣ Interrupts and Flags
–16–
REV. 0
ADSP-2184
Parameter
Min
Max
Unit
Bus Request–Bus Grant
Timing Requirements:
tBH
BR Hold after CLKOUT High1
tBS
BR Setup before CLKOUT Low1
0.25 tCK + 2
0.25 tCK + 17
Switching Characteristics:
tSD
CLKOUT High to xMS, RD, WR Disable
tSDB
xMS, RD, WR Disable to BG Low
tSE
BG High to xMS, RD, WR Enable
tSEC
xMS, RD, WR Enable to CLKOUT High
tSDBH
xMS, RD, WR Disable to BGH Low2
tSEH
BGH High to xMS, RD, WR Enable 2
0
0
0.25 tCK – 7
0
0
ns
ns
0.25 tCK + 10
ns
ns
ns
ns
ns
ns
NOTES
xMS = PMS, DMS, CMS, IOMS, BMS.
1BR is an asynchronous signal. If BR meets the setup/hold requirements, it will be recognized during the current clock cycle; otherwise the signal will be recognized on
the following cycle. Refer to the ADSP-2100 Family User’s Manual, Third Edition, for BR/BG cycle relationships.
2BGH is asserted when the bus is granted and the processor requires control of the bus to continue.
tBH
CLKOUT
BR
tBS
CLKOUT
PMS, DMS
BMS, RD
WR
BG
BGH
tSD
tSEC
tSDB
tSE
tSDBH
tSEH
Figure 11.␣ Bus Request–Bus Grant
REV. 0
–17–
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
0.5 tCK – 9 + w
0.75 tCK – 12.5 + w
ns
ns
ns
Memory Read
Timing Requirements:
RD Low to Data Valid
tRDD
tAA
A0–A13, xMS to Data Valid
tRDH
Data Hold from RD High
1
Switching Characteristics:
tRP
RD Pulsewidth
tCRD
CLKOUT High to RD Low
tASR
A0–A13, xMS Setup before RD Low
tRDA
A0–A13, xMS Hold after RD Deasserted
tRWR
RD High to RD or WR Low
0.5 tCK – 5 + w
0.25 tCK – 5
0.25 tCK – 6
0.25 tCK – 3
0.5 tCK – 5
0.25 tCK + 7
ns
ns
ns
ns
ns
w = wait states × t CK.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0 – A13
DMS, PMS,
BMS, IOMS,
CMS
tRDA
RD
tASR
tRP
tCRD
tRWR
D
tRDD
tAA
tRDH
WR
Figure 12.␣ Memory Read
–18–
REV. 0
ADSP-2184
Parameter
Min
Max
Unit
Memory Write
Switching Characteristics:
Data Setup before WR High
tDW
tDH
Data Hold after WR High
tWP
WR Pulsewidth
tWDE
WR Low to Data Enabled
A0–A13, xMS Setup before WR Low
tASW
tDDR
Data Disable before WR or RD Low
tCWR
CLKOUT High to WR Low
tAW
A0–A13, xMS, Setup before WR Deasserted
tWRA
A0–A13, xMS Hold after WR Deasserted
tWWR
WR High to RD or WR Low
0.5 tCK – 7+ w
0.25 tCK – 2
0.5 tCK – 5 + w
0
0.25 tCK – 6
0.25 tCK – 7
0.25 tCK – 5
0.75 tCK – 9 + w
0.25 tCK – 3
0.5 tCK – 5
0.25 tCK + 7
w = wait states × tCK.
xMS = PMS, DMS, CMS, IOMS, BMS.
CLKOUT
A0–A13
DMS, PMS,
BMS, CMS,
IOMS
tWRA
WR
tASW
tWWR
tWP
tAW
tDH
tCWR
D
tWDE
tDW
RD
Figure 13.␣ Memory Write
REV. 0
–19–
tDDR
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
Serial Ports
Timing Requirements:
SCLK Period
tSCK
tSCS
DR/TFS/RFS Setup before SCLK Low
tSCH
DR/TFS/RFS Hold after SCLK Low
tSCP
SCLKIN Width
50
4
8
20
Switching Characteristics:
tCC
CLKOUT High to SCLKOUT
tSCDE
SCLK High to DT Enable
tSCDV
SCLK High to DT Valid
tRH
TFS/RFSOUT Hold after SCLK High
TFS/RFSOUT Delay from SCLK High
tRD
tSCDH
DT Hold after SCLK High
tTDE
TFS (Alt) to DT Enable
tTDV
TFS (Alt) to DT Valid
tSCDD
SCLK High to DT Disable
tRDV
RFS (Multichannel, Frame Delay Zero) to DT Valid
CLKOUT
tCC
ns
ns
ns
ns
0.25 tCK
0
0.25 tCK + 10
15
0
15
0
0
14
15
15
tCC
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSCK
SCLK
tSCP
tSCS
tSCP
tSCH
DR
TFSIN
RFSIN
tRD
tRH
RFSOUT
TFSOUT
tSCDD
tSCDV
tSCDH
tSCDE
DT
tTDE
tTDV
TFSOUT
ALTERNATE
FRAME MODE
tRDV
RFSOUT
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
TFSIN
tTDE
tTDV
ALTERNATE
FRAME MODE
RFSIN
tRDV
MULTICHANNEL
MODE,
FRAME DELAY 0
(MFD = 0)
Figure 14. Serial Ports
–20–
REV. 0
ADSP-2184
Parameter
Min
Max
Unit
IDMA Address Latch
Timing Requirements:
Duration of Address Latch1, 2
tIALP
tIASU
IAD15–0 Address Setup before Address Latch End2
tIAH
IAD15–0 Address Hold after Address Latch End2
tIKA
IACK Low before Start of Address Latch2, 3
tIALS
Start of Write or Read after Address Latch End2, 3
10
5
3
0
3
NOTES
1Start of Address Latch = IS Low and IAL High.
2End of Address Latch = IS High or IAL Low.
3Start of Write or Read = IS Low and IWR Low or IRD Low.
IACK
tIKA
IAL
tIALP
IS
tIASU
tIAH
IAD 15–0
tIALS
IRD OR
IWR
Figure 15. IDMA Address Latch
REV. 0
–21–
ns
ns
ns
ns
ns
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
IDMA Write, Short Write Cycle
Timing Requirements:
IACK Low before Start of Write1
tIKW
tIWP
Duration of Write1, 2
tIDSU
IAD15–0 Data Setup before End of Write2, 3, 4
tIDH
IAD15–0 Data Hold after End of Write2, 3, 4
0
15
5
2
Switching Characteristic:
tIKHW
Start of Write to IACK High
ns
ns
ns
ns
15
ns
NOTES
1Start of Write = IS Low and IWR Low.
2End of Write = IS High or IWR High.
3If Write Pulse ends before IACK Low, use specifications t
IDSU, t IDH.
4If Write Pulse ends after IACK Low, use specifications t
IKSU, tIKH .
tIKW
IACK
tIKHW
IS
tIWP
IWR
tIDSU
IAD 15–0
tIDH
DATA
Figure 16. IDMA Write, Short Write Cycle
–22–
REV. 0
ADSP-2184
Parameter
Min
Max
Unit
IDMA Write, Long Write Cycle
Timing Requirements:
tIKW
IACK Low before Start of Write1
tIKSU
IAD15–0 Data Setup before IACK Low2, 3, 4
tIKH
IAD15–0 Data Hold after IACK Low2, 3, 4
0
0.5 tCK + 10
2
Switching Characteristics:
tIKLW
Start of Write to IACK Low4
tIKHW
Start of Write to IACK High
ns
ns
ns
1.5 tCK
15
ns
ns
NOTES
1Start of Write = IS Low and IWR Low.
2If Write Pulse ends before IACK Low, use specifications t
IDSU, t IDH.
3If Write Pulse ends after IACK Low, use specifications t
IKSU, tIKH .
4This is the earliest time for IACK Low from Start of Write. For IDMA Write cycle relationships, please refer to the ADSP-2100 Family User’s Manual, Third Edition.
tIKW
IACK
tIKHW
tIKLW
IS
IWR
tIKSU
tIKH
DATA
IAD 15–0
Figure 17. IDMA Write, Long Write Cycle
REV. 0
–23–
ADSP-2184
TIMING PARAMETERS
Parameter
Min
Max
Unit
IDMA Read, Long Read Cycle
Timing Requirements:
IACK Low before Start of Read1
tIKR
tIRK
End of Read after IACK Low
0
2
Switching Characteristics:
tIKHR
IACK High after Start of Read1
tIKDS
IAD15–0 Data Setup before IACK Low
IAD15–0 Data Hold after End of Read2
tIKDH
tIKDD
IAD15–0 Data Disabled after End of Read2
tIRDE
IAD15–0 Previous Data Enabled after Start of Read
tIRDV
IAD15–0 Previous Data Valid after Start of Read
tIRDH1
IAD15–0 Previous Data Hold after Start of Read (DM/PM1)3
tIRDH2
IAD15–0 Previous Data Hold after Start of Read (PM2)4
ns
ns
15
0.5 tCK – 10
0
10
0
15
2 tCK – 5
tCK – 5
ns
ns
ns
ns
ns
ns
ns
ns
NOTES
1Start of Read = IS Low and IRD Low.
2End of Read = IS High or IRD High.
3DM read or first half of PM read.
4Second half of PM read.
IACK
tIKHR
tIKR
IS
tIRK
IRD
tIKDH
tIKDS
tIRDE
PREVIOUS
DATA
IAD 15–0
READ
DATA
tIRDV
tIKDD
tIRDH
Figure 18. IDMA Read, Long Read Cycle
–24–
REV. 0
ADSP-2184
Parameter
Min
Max
Unit
IDMA Read, Short Read Cycle
Timing Requirements:
tIKR
IACK Low before Start of Read1
tIRP
Duration of Read
0
15
Switching Characteristics:
tIKHR
IACK High after Start of Read1
tIKDH
IAD15–0 Data Hold after End of Read2
tIKDD
IAD15–0 Data Disabled after End of Read2
tIRDE
IAD15–0 Previous Data Enabled after Start of Read
tIRDV
IAD15–0 Previous Data Valid after Start of Read
15
0
10
0
15
NOTES
1Start of Read = IS Low and IRD Low.
2End of Read = IS High or IRD High.
IACK
tIKR
tIKHR
IS
tIRP
IRD
tIKDH
tIRDE
PREVIOUS
DATA
IAD 15–0
tIRDV
tIKDD
Figure 19.␣ IDMA Read, Short Read Cycle
REV. 0
–25–
ns
ns
ns
ns
ns
ns
ns
ADSP-2184
OUTPUT DRIVE CURRENTS
2184 POWER, INTERNAL1, 2, 3
60
VDD = 5.0V @ +258C
VOH
SOURCE CURRENT – mA
40
VDD = 5.5V @ –408C
20
400
350
325
330mW
300
300mW
VDD = 5.0V
275
250
250mW
225
225mW
VDD = 4.5V
200
VDD = 4.5V @ +858C
175
150
0
180mW
33.33
40
1/tCYC – MHz
VDD = 4.5V @ +858C
–20
385mW
VDD = 5.5V
375
POWER (PINT) – mW
Figure 20 shows typical I-V characteristics for the output drivers
of the ADSP-2184. The curves represent the current drive
capability of the output drivers as a function of output voltage.
POWER, IDLE1, 2, 4
VDD = 5.0V @ +258C
VOL
95
91.52mW
VDD = 5.5V
90
–40
85
VDD = 5.5V @ –408C
0
10
20
30
40
SOURCE VOLTAGE – V
50
POWER (PIDLE) – mW
–60
60
Figure 20. Typical Drive Currents
POWER DISSIPATION
80
75
70
60
70.55mW
VDD = 4.5V
51.705mW
62.1mW
55
45
40
C × VDD2 × f
VDD = 5.0V
65
50
To determine total power dissipation in a specific application,
the following equation should be applied for each output:
44.73mW
33.33
40
1/tCYC – MHz
C = load capacitance, f = output switching frequency.
POWER, IDLE n MODES2
75
Example
• External data memory writes occur every other cycle with
50% of the data pins switching.
POWER (PIDLEn) – mW
• External data memory is accessed every cycle with 50% of the
address pins switching.
60
55
50
45
40
30
• The application operates at VDD = 5.0 V and tCK = 25 ns.
33.33
40
1POWER REFLECTS DEVICE OPERATING WITH NO OUTPUT LOADS.
2I
DD MEASUREMENT TAKEN WITH ALL INSTRUCTIONS EXECUTING FROM INTERNAL
MEMORY. 50% OF THE INSTRUCTIONS ARE MULTIFUNCTION (TYPES 1, 4, 5, 12, 13, 14)
30% ARE TYPE 2 AND TYPE 6, AND 20% ARE IDLE INSTRUCTIONS.
(C × VDD2 × f) is calculated for each output:
× 52 V
× 52 V
× 52 V
× 52 V
32.8mW
IDLE (16)
IDLE (128)
VALID FOR ALL TEMPERATURE GRADES.
PINT = internal power dissipation from Power vs. Frequency
graph (Figure 21).
× 10 pF
× 10 pF
× 10 pF
× 10 pF
34.3mW
1/tCYC – MHz
Total Power Dissipation = PINT + (C × VDD2 × f)
8
9
1
1
36.6mW
34.7mW
25
ⴛ VDD
62.1mW
35
• Each address and data pin has a 10 pF total load at the pin.
2
IDLE
65
Assumptions
# of
Pins ⴛ C
70.55mW
70
In an application where external data memory is used and no
other outputs are active, power dissipation is calculated as follows:
Address, DMS
Data Output, WR
RD
CLKOUT
82.28mW
3IDLE REFERS TO ADSP-2184 STATE OF OPERATION DURING EXECUTION OF IDLE
INSTRUCTION. DEASSERTED PINS ARE DRIVEN TO EITHER VDD OR GND.
4TYPICAL POWER DISSIPATION AT 5.0V V
DD AND TA = 258C EXCEPT WHERE SPECIFIED.
ⴛf
Figure 21. Power vs. Frequency
× 40 MHz = 80 mW
× 20 MHz = 45 mW
× 20 MHz = 5 mW
× 40 MHz = 10 mW
140 mW
Total power dissipation for this example is PINT + 40 mW.
–26–
REV. 0
ADSP-2184
CAPACITIVE LOADING
Figures 22 and 23 show the capacitive loading characteristics of
the ADSP-2184.
is calculated. If multiple pins (such as the data bus) are disabled, the measurement value is that of the last pin to stop
driving.
30
T = +858C
VDD = 4.5V
INPUT
OR
OUTPUT
RISE TIME (0.4V–2.4V) – ns
25
Output Enable Time
15
10
5
50
0
100
150
CL – pF
200
250
300
Figure 22. Typical Output Rise Time vs. Load Capacitance,
CL (at Maximum Ambient Operating Temperature)
Output pins are considered to be enabled when that have made
a transition from a high-impedance state to when they start
driving. The output enable time (tENA) is the interval from when
a reference signal reaches a high or low voltage level to when the
output has reached a specified high or low trip point, as shown
in the Output Enable/Disable diagram. If multiple pins (such as
the data bus) are enabled, the measurement value is that of the
first pin to start driving.
REFERENCE
SIGNAL
tMEASURED
18
tENA
VOH
(MEASURED)
16
VALID OUTPUT DELAY OR HOLD – ns
1.5V
Figure 24. Voltage Reference Levels for AC Measurements (Except Output Enable/Disable)
20
0
1.5V
14
12
tDIS
VOH
(MEASURED)
VOH (MEASURED) – 0.5V
2.0V
VOL (MEASURED) +0.5V
1.0V
OUTPUT
10
VOL
(MEASURED)
8
VOL
(MEASURED)
tDECAY
6
OUTPUT
STARTS
DRIVING
OUTPUT STOPS
DRIVING
4
2
HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.
NOMINAL
–2
Figure 25. Output Enable/Disable
–4
–6
0
50
100
150
200
IOL
250
CL – pF
Figure 23. Typical Output Valid Delay or Hold vs. Load
Capacitance, CL (at Maximum Ambient Operating
Temperature)
TO
OUTPUT
PIN
TEST CONDITIONS
Output Disable Time
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured
output high or low voltage to a high impedance state. The output disable time (tDIS) is the difference of tMEASURED and tDECAY,
as shown in the Output Enable/Disable diagram. The time is the
interval from when a reference signal reaches a high or low
voltage level to when the output voltages have changed by 0.5 V
from the measured output high or low voltage. The decay time,
tDECAY, is dependent on the capacitive load, CL, and the current
load, iL, on the output pin. It can be approximated by the following equation:
tDECAY =
IOH
Figure 26. Equivalent Device Loading for AC Measurements (Including All Fixtures)
CL × 0.5V
iL
from which
tDIS = tMEASURED – tDECAY
REV. 0
+1.5V
50pF
–27–
ADSP-2184
ENVIRONMENTAL CONDITIONS
10k
Ambient Temperature Rating:
=
=
=
=
=
=
TCASE – (PD ⫻ θ CA)
Case Temperature in °C
Power Dissipation in W
Thermal Resistance (Case-to-Ambient)
Thermal Resistance (Junction-to-Ambient)
Thermal Resistance (Junction-to-Case)
Package
␪JA
␪JC
␪CA
LQFP
50°C/W
2°C/W
48°C/W
5.6V
1k
IDD – mA
TAMB
TCASE
PD
θCA
θJA
θJC
5.0V
100
10
1
0
20
40
60
80
TEMPERATURE – 8C
100
120
Figure 27. Power-Down Supply Current
–28–
REV. 0
ADSP-2184
A4/IAD3
A5/IAD4
1
2
78 D18
77 D17
76 D16
80 GND
79 D19
82 D21
81 D20
84 D23
83 D22
86 FL1
85 FL2
87 FL0
89 PF2 [MODE C]
88 PF3
91 PWD
90 VDD
92 GND
94 PF0 [MODE A]
93 PF1 [MODE B]
95 BGH
96 PWDACK
98 A1/IAD0
97 A0
100 A3/IAD2
99 A2/IAD1
100-Lead LQFP Package Pinout
75 D15
74 D14
PIN 1
IDENTIFIER
GND
3
A6/IAD5
4
73 D13
72 D12
A7/IAD6
5
71 GND
A8/IAD7
A9/IAD8
6
70 D11
69 D10
A10/IAD9
8
7
68 D9
67 VDD
A11/IAD10 9
A12/IAD11 10
66 GND
A13/IAD12 11
GND 12
65 D8
64 D7/IWR
ADSP-2184
CLKIN 13
63 D6/IRD
TOP VIEW
(Not to Scale)
XTAL 14
VDD 15
62 D5/IAL
61 D4/IS
CLKOUT 16
GND 17
60 GND
59 VDD
58 D3/IACK
VDD 18
WR 19
RD 20
57 D2/IAD15
BMS 21
DMS 22
55 D0/IAD13
54 BG
PMS 23
53 EBG
52 BR
56 D1/IAD14
IOMS 24
CMS 25
–29–
EINT 50
ELIN 49
ELOUT 48
EMS 45
EE 46
ECLK 47
RESET 44
ERESET 43
GND 41
SCLK1 42
RFS1 39
DR1 40
DT1 37
TFS1 38
VDD 36
DR0 34
SCLK0 35
RFS0 33
TFS0 32
IRQ2+PF7 30
DT0 31
GND 28
IRQL1+PF6 29
IRQE+PF4 26
REV. 0
IRQL0+PF5 27
51 EBR
ADSP-2184
The ADSP-2184 package pinout is shown in the table below. Pin names in bold text replace the plain text named functions when
Mode C = 1. A + sign separates two functions when either function can be active for either major I/O mode. Signals enclosed in
brackets [␣ ] are state bits latched from the value of the pin at the deassertion of RESET.
LQFP Pin Configurations
LQFP
Number
Pin
Name
LQFP
Number
Pin
Name
LQFP
Number
Pin
Name
LQFP
Number
Pin
Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
A4/IAD3
A5/IAD4
GND
A6/IAD5
A7/IAD6
A8/IAD7
A9/IAD8
A10/IAD9
A11/IAD10
A12/IAD11
A13/IAD12
GND
CLKIN
XTAL
VDD
CLKOUT
GND
VDD
WR
RD
BMS
DMS
PMS
IOMS
CMS
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
IRQE + PF4
IRQL0 + PF5
GND
IRQL1 + PF6
IRQ2 + PF7
DT0
TFS0
RFS0
DR0
SCLK0
VDD
DT1
TFS1
RFS1
DR1
GND
SCLK1
ERESET
RESET
EMS
EE
ECLK
ELOUT
ELIN
EINT
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
EBR
BR
EBG
BG
D0/IAD13
D1/IAD14
D2/IAD15
D3/IACK
VDD
GND
D4/IS
D5/IAL
D6/IRD
D7/IWR
D8
GND
VDD
D9
D10
D11
GND
D12
D13
D14
D15
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
D16
D17
D18
D19
GND
D20
D21
D22
D23
FL2
FL1
FL0
PF3
PF2 [Mode C]
VDD
PWD
GND
PF1 [Mode B]
PF0 [Mode A]
BGH
PWDACK
A0
A1/IAD0
A2/IAD1
A3/IAD2
–30–
REV. 0
ADSP-2184
ORDERING GUIDE
Instruction
Rate
(MHz)
Package
Description
Package
Option*
ADSP-2184BST-160
–40°C to +85°C
40.0
100-Lead LQFP
ST-100
C3418–2–5/99
Part Number
Ambient
Temperature
Range
*ST = Plastic Thin Quad Flatpack (LQFP).
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
100-Lead Metric Thin Plastic Quad Flatpack (LQFP)
(ST-100)
0.640 (16.25)
0.630 (16.00) TYP SQ
0.620 (15.75)
0.553 (14.05)
0.551 (14.00) TYP SQ
0.549 (13.95)
0.063 (1.60) MAX
0.030 (0.75)
0.024 (0.60) TYP
128
0.020 (0.50)
TYP
SEATING
PLANE
0.472 (12.00) BSC
100
1
76
75
TOP VIEW
(PINS DOWN)
0.004
(0.102)
MAX LEAD
COPLANARITY
08 – 78
68 ± 48
25
26
0.007 (0.177)
0.005 (0.127) TYP
0.003 (0.077)
51
50
0.020 (0.50)
BSC
LEAD PITCH
0.011 (0.27)
0.009 (0.22) TYP
0.007 (0.17)
LEAD WIDTH
PRINTED IN U.S.A.
NOTE:
THE ACTUAL POSITION OF EACH LEAD IS WITHIN (0.08) 0.0032 FROM
ITS IDEAL POSITION WHEN MEASURED IN THE LATERAL DIRECTION.
CENTER FIGURES ARE TYPICAL UNLESS OTHERWISE NOTED
REV. 0
–31–