LTC1043 - Dual Precision Instrumentation Switched-Capacitor Building Block

LTC1043
Dual Precision
Instrumentation Switched Capacitor
Building Block
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
The LTC®1043 is a monolithic, charge-balanced, dual
switched capacitor instrumentation building block. A pair
of switches alternately connects an external capacitor to
an input voltage and then connects the charged capacitor
across an output port. The internal switches have a
break-before-make action. An internal clock is provided
and its frequency can be adjusted with an external
capacitor. The LTC1043 can also be driven with an external
CMOS clock.
Instrumentation Front End with 120dB CMRR
Precise, Charge-Balanced Switching
Operates from 3V to 18V
Internal or External Clock
Operates up to 5MHz Clock Rate
Low Power
Two Independent Sections with One Clock
U
APPLICATIO S
■
■
■
■
■
The LTC1043, when used with low clock frequencies,
provides ultra precision DC functions without requiring
precise external components. Such functions are
differential voltage to single-ended conversion, voltage
inversion, voltage multiplication and division by 2, 3, 4, 5,
etc. The LTC1043 can also be used for precise V–F and
F–V circuits without trimming, and it is also a building
block for switched capacitor filters, oscillators and
modulators.
Precision Instrumentation Amplifiers
Ultra Precision Voltage Inverters, Multipliers
and Dividers
V–F and F–V Converters
Sample-and-Hold
Switched Capacitor Filters
The LTC1043 is manufactured using Linear Technology’s
enhanced LTCMOSTM silicon gate process.
, LTC and LT are registered trademarks of Linear Technology Corporation.
LTCMOS is a trademark of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Instrumentation Amplifier
5V
4
140
5V
3
8
1µF
CH
11
1µF
(EXTERNAL)
CS
+
1/2 LTC1013
2
–
CS = CH = 1µF
120
8
1
VOUT
4
–5V
100
CMRR (dB)
7
DIFFERENTIAL
INPUT
CMRR vs Frequency
80
60
12
1µF
13
14
R1
16
1/2 LTC1043
0.01µF
17
LTC1043 • TA01
–5V
R2
CMRR > 120dB AT DC
CMRR > 120dB AT 60Hz
DUAL SUPPLY OR SINGLE 5V
GAIN = 1 + R2/R1
VOS ≈ 150µV
40
20
100
1k
10k
100k
FREQUENCY OF COMMON MODE SIGNAL
LTC1043 • TA02
∆ VOS
≈ 2µV/°C
∆T
COMMON MODE INPUT VOLTAGE INCLUDES THE SUPPLIES
1043fa
1
LTC1043
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
ORDER PART
NUMBER
TOP VIEW
Supply Voltage ........................................................ 18V
Input Voltage at Any Pin .......... –0.3V ≤ VIN ≤ V+ + 0.3V
Operating Temperature Range
LTC1043C ................................... –40°C ≤ TA ≤ 85°C
LTC1043M (OBSOLETE).............– 55°C ≤ TA ≤ 125°C
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
SH B
1
18 S3B
CB+
2
17 V –
CB–
3
16 COSC
V+
4
15 S4B
S2B
5
14 S4A
S1B
6
13 S3A
S1A
7
12 CA–
S2A
8
11 CA+
NC
9
10 SHA
LTC1043CN
LTC1043CSW
N PACKAGE
18-LEAD PDIP
SW PACKAGE
18-LEAD PLASTIC SO
TJMAX = 100°C, θJA = 100°C/W PACKAGE (N)
TJMAX = 150°C, θJA = 85°C/W PACKAGE (SW)
LTC1043MD
D PACKAGE
18-LEAD SIDE BRAZED (HERMETIC)
OBSOLETE PACKAGE
Consider the N18 Package as an Alternate Source
LTC1043 • POI01
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
+
The ● denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. V = 10V, V– = 0V, LTC1043M operates from –55°C ≤ TA ≤ 125°C; LTC1043C operates from
–40°C ≤ TA ≤ 85°C, unless otherwise noted.
SYMBOL PARAMETER
IS
Power Supply Current
CONDITIONS
MIN
Pin 16 Connected High or Low
LTC1043M
TYP MAX
OFF Leakage Current
Any Switch, Test Circuit 1 (Note 2)
●
RON
RON
fOSC
IOSC
ON Resistance
ON Resistance
Internal Oscillator Frequency
Pin Source or Sink Current
Test Circuit 2, VIN = 7V, 1 = ±0.5mA
V+ = 10V, V – = 0V
●
Test Circuit 2, VIN = 3.1V, 1 = ±0.5mA
V + = 5V, V – = 0V
●
COSC (Pin 16 to V –) = 0pF
COSC (Pin 16 to V –) = 100pF
Test Circuit 3
●
Pin 16 at V+ or V –
20
15
0.25
0.4
0.7
mA
mA
0.4
0.65
1
0.4
0.65
1
mA
mA
6
6
100
500
6
6
100
pA
nA
240
400
700
240
400
700
Ω
Ω
400
700
1
400
700
1
Ω
kΩ
50
75
kHz
kHz
kHz
70
100
µA
µA
185
34
40
●
Break-Before-Make Time
UNITS
0.4
0.7
●
II
LTC1043C
TYP MAX
0.25
●
COSC (Pin 16 to V –) = 100pF
MIN
50
75
70
100
20
15
185
34
40
25
25
ns
Clock to Switching Delay
COSC Pin Externally Driven
75
75
ns
fM
Max External CLK Frequency
COSC Pin Externally Driven with CMOS Levels
5
5
MHz
CMRR
Common Mode Rejection Ratio
V+ = 5V, V – = –5V, –5V < VCM < 5V
DC to 400Hz
120
120
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
2
dB
Note 2: OFF leakage current is guaranteed but not tested at 25°C.
1043fa
LTC1043
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Power Supply Current vs
Power Supply Voltage
RON vs VIN
1.6
550
TA = –55°C
COSC = 0pF
1.4
COSC = 0.0047pF
RON vs VIN
RON (PEAK)
500
I = 100µA
450 V
IN
1.2
TA = 25°C
COSC = 0pF
1.0
COSC = 0.0047pF
0.8
TA = 125°C
COSC = 0pF
0.6
COSC = 0.0047pF
0.4
280
V+ = 5V
V – = 0V
TA = 25°C
0.2
V+ = 10V
V – = 0V
TA = 25°C
RON (PEAK)
260
240 VIN
I = 100µA
220
400
350
300
I = 100µA
250
200
RON (Ω)
RON (Ω)
SUPPLY CURRENT (mA)
(Test Circuits 2 through 4)
180
I = 100µA
160
I = mA
200
140
150
120
100
100
I = mA
0
2
4
6
1
0
8 10 12 14 16 18 20
VSUPPLY (V)
3
2
4
LTC1043 • TPC01
180
160
I = 100µA
140
800
600
700
500
200
80
100
8
0
10 12 14 16 18 20
VIN (V)
VIN ≈ 3.2V
400
300
6
VIN ≈ 7V
3V ≤ V+ + ≤18V
V – = 0V
TA = 25°C
0
2
4
6
250
225
VIN ≈ 15.1V
fOSC (kHz)
fOSC (Hz)
TA = 125°C
TA = 70°C
TA = –55°C
200
100
8 10 12 14 16 18 20
VSUPPLY (V)
0
V+ = 15V, V – = 0V
2
4
6
8 10 12 14 16 18 20
VSUPPLY (V)
LTC1043 • TPC06
Normalized Oscillator Frequency,
fOSC vs Supply Voltage
2.0
COSC = 0pF
175
V+ = 10V, V – = 0V
V+ = 5V, V – = 0V
150
125
100
75
1k
50
10
300
TA = 25°C
200
100k
9
500
Oscillator Frequency, fOSC
vs Supply Voltage
TA = 25°C
10k
600
LTC1043 • TPC05
Oscillator Frequency, fOSC
vs COSC
8
I = 100µA
VIN
400
VIN ≈ 11V
LTC1043 • TPC04
1M
900
I = 100µA
VIN
800
100
4
7
RON (PEAK)
1000
700
120
2
5 6
VIN (V)
1100
RON (PEAK)
VIN = 1.6V
900
I = mA
0
4
RON (Peak) vs Power Supply
Voltage and Temperature
RON (Ω)
I = 100µA
1000
RON (Ω)
RON (Ω)
220 V
IN
200
V+ = 15V
V – = 0V
TA = 25°C
3
LTC1043 • TPC03
RON (Peak) vs Power Supply
Voltage
RON (PEAK)
240
2
LTC1043 • TPC02
RON vs VIN
260
1
0
5
VIN (V)
OSCILLATOR FREQUENCY
NORMALIZED TO fOSC AT 5V SUPPLY
0
COSC = 100pF
25
0pF < COSC < 0.01µF
TA = 25°C
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
100
0
2k
4k
6k
COSC (pF)
8k
10k
LTC1043 • TPC07
0
2
4
6
8 10 12 14 16 18 20
VSUPPLY (V)
LTC1043 • TPC08
0
2
4
6
8 10 12 14 16 18 20
VSUPPLY (V)
LTC1043 • TPC09
1043fa
3
LTC1043
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Oscillator Frequency, fOSC
vs Ambient Temperature, TA
COSC Pin ISINK, ISOURCE
vs Supply Voltage
350
fOSC (kHz)
275
250
225
200
V+ = 10V, V– = 0V
175
125
V+
–
= 5V, V = 0V
V+ = 15V, V– = 0V
100
50
25
0
75 100
–50 –25
AMBIENT TEMPERATURE (°C)
80
ISINK, TA = –55°C
75
60
ISINK, TA = 25°C
ISOURCE, TA = –55°C
50
ISOURCE, TA = 25°C
50
40
30
25
ISINK, TA = 125°C
20
ISOURCE, TA = 125°C
0
0
125
TA = 25°C
70
tNOV (ns)
300
150
Break-Before-Make Time, tNOV,
vs Supply Voltage
100
COSC = 0pF
PIN 16 SOURCE OR SINK CURRENT (µA)
325
(Test Circuits 2 through 4)
2
4
6
8
10
12
14
16
10
18
0
LTC1043 • TPC11
LTC1043 • TPC10
2
4
6
8 10 12 14 16 18 20
VSUPPLY (V)
LTC1043 • TPC12
W
BLOCK DIAGRA
S1A
7
S2A
8
SHA 10
11 CA+
12 CA–
S3A
13
S4A
14
CHARGE
BALANCING
CIRCUITRY
S1B
6
SHB 1
S2B
5
2 CB+
3 CB–
S3B
18
S4B
15
CHARGE
BALANCING
CIRCUITRY
NON-OVERLAPPING
CLOCK
V+
V–
COSC
16
OSCILLATOR
V+
4
V–
17
THE CHARGE BALANCING CIRCUITRY SAMPLES THE VOLTAGE
AT S3 WITH RESPECT TO S4 (PIN 16 HIGH) AND INJECTS A
SMALL CHARGE AT THE C+ PIN (PIN 16 LOW).
THIS BOOSTS THE CMRR WHEN THE LTC1043 IS USED AS AN
INSTRUMENTATION AMPLIFIER FRONT END.
FOR MINIMUM CHARGE INJECTION IN OTHER TYPES OF
APPLICATIONS, S3A AND S3B SHOULD BE GROUNDED
THE SWITCHES ARE TIMED AS SHOWN WITH PIN 16 HIGH
LTC1043 • BD01
1043fa
4
LTC1043
TEST CIRCUITS
Test Circuit 1. Leakage Current Test
(7, 13, 6, 18)
(7, 13, 6, 18)
(8, 14, 5, 15)
A
0V TO 10V
Test Circuit 2. RON Test
+
(11, 12, 2, 3)
NOTE: TO OPEN SWITCHES,
S1 AND S3
SHOULD BE CONNECTED
TO V –. TO OPEN S2, S4,
COSC PIN SHOULD BE
TO V+ COSC
+
(8, 14, 5, 15)
VIN
(11, 12, 2, 3)
100µA to 1mA
CURRENT SOURCE
LTC1043 • TC01
A
LTC1043 • TC02
Test Circuit 3. Oscillator Frequency, fOSC
Test Circuit 4. CMRR Test
7
V–
(TEST PIN) 2
17
10
COSC
V+
4
+
LTC1043
VOUT
8
11
+
16
1µF
1µF
CAPACITORS ARE
NOT ELECTROLYTIC
5
12
+
6
IV
13
14
LTC1043 • TC03
+
V– ≤ VCM ≤ V+
CMRR = 20 LOG
( )
VCM
VOUT
NOTE: FOR OPTIMUM CMRR, THE COSC SHOULD
BE LARGER THAN 0.0047µF, AND
THE SAMPLING CAPACITOR ACROSS
PINS 11 AND 12 SHOULD BE PLACED
OVER A SHIELD TIED TO PIN 10
LTC1043 • TC04
U
W
U U
APPLICATIO S I FOR ATIO
Common Mode Rejection Ratio (CMRR)
The LTC1043, when used as a differential to single-ended
converter rejects common mode signals and preserves
differential voltages (Figure 1). Unlike other techniques,
the LTC1043’s CMRR does not degrade with increasing
common mode voltage frequency. During the sampling
mode, the impedance of Pins 2, 3 (and 11, 12) should be
reasonably balanced, otherwise, common mode signals
will appear differentially. The value of the CMRR depends
on the value of the sampling and holding capacitors
(CS, CH) and on the sampling frequency. Since the
common mode voltages are not sampled, the
common mode signal frequency can well exceed the
sampling frequency without experiencing aliasing
phenomena. The CMRR of Figure 1 is measured by
1/2 LTC1043
7
8
C+ 11
VD
+
+
CS
VD
CH
C– 12
13
VCM
14
+
CS, CH ARE MYLAR OR POLYSTRENE
LTC1043 • AI01
Figure 1. Differential to Single-Ended Converter
1043fa
5
LTC1043
U
W
U U
APPLICATIO S I FOR ATIO
shorting Pins 7 and 13 and by observing, with a precision
DVM, the change of the voltage across CH with respect to
an input CM voltage variation. During the sampling and
holding mode, charges are being transferred and minute
voltage transients will appear across the holding capacitor. Although the RON on the switches is low enough to
allow fast settling, as the sampling frequency increases,
the rate of charge transfer increases and the average
voltage measured with a DVM across it will increase
proportionally; this causes the CMRR of the sampled data
system, as seen by a “continuous” instrument (DVM), to
decrease (Figure 2).
Switch Charge Injection
Figure 3 shows one out of the eight switches of the
LTC1043, configured as a basic sample-and-hold circuit.
When the switch opens, a ‘‘hold step’’ is observed and its
magnitude depends on the value of the input voltage.
Figure 4 shows charge injected into the hold capacitor. For
instance, a 2pCb of charge injected into a 0.01µF capacitor
causes a 200µV hold step. As shown in Figure 4, there is
a predictable and repeatable charge injection cancellation
when the input voltage is close to half the supply voltage
of the LTC1043. This is a unique feature of this product,
containing charge-balanced switches fabricated with a
self-aligning gate CMOS process. Any switch of the
LTC1043, when powered with symmetrical dual supplies,
will sample-and-hold small signals around ground without any significant error.
Shielding the Sampling Capacitor for Very High CMRR
Internal or external parasitic capacitors from the C + pin(s)
to ground affect the CMRR of the LTC1043 (Figure 1).
The common mode error due to the internal junction
capacitances of the C + Pin(s) 2 and 11 is cancelled through
internal circuitry. The C + pin, therefore, should be used as
the top plate of the sampling capacitor. The interpin
capacitance between pin 2 and dummy Pin 1 (11 and 10)
appears in parallel with the sampling capacitor so it does
not degrade the CMRR. A shield placed underneath
the sampling capacitor and connected to either Pin 1 or 3
helps to boost the CMRR in excess of 120dB (Figure 5).
Excessive external parasitic capacitance between the C –
pins and ground indirectly degrades CMRR; this becomes
visible especially when the LTC1043 is used with clock
frequencies above 2kHz. Because of this, if a shield is
used, the parasitic capacitance between the shield and
circuit ground should be minimized.
It is recommended that the outer plate of the sampling
capacitor be connected to the C – pin(s).
Input Pins, SCR Sensitivity
An internal 60Ω resistor is connected in series with the
input of the switches (Pins 5, 6, 7, 8, 13, 14, 15, 18) and
it is included in the RON specification. When the input
voltage exceeds the power supply by a diode drop, current
will flow into the input pin(s). The LTC1043 will not latch
until the input current reaches 2mA–3mA. The device will
140
120
CS = CH = 1µF
5V
CS = 1µF, CZH = 0.1µF
2
+
6
CMRR (dB)
100
1/2 LTC1013
1/8 LTC1043
VOUT
–
80
VIN
1000pF
–5V
60
V+
40
SAMPLE
HOLD TO PIN 16
0V
LTC1043 • AI03
20
100
1k
10k
100k
fOSC (Hz)
LTC1043 • AI02
Figure 2. CMRR vs Sampling Frequency
Figure 3
1043fa
6
LTC1043
U
W
U U
APPLICATIO S I FOR ATIO
recover from the latch mode when the input drops 3V to 4V
below the voltage value which caused the latch. For
instance, if an external resistor of 200Ω is connected in
series with an input pin, the input can be taken 1.3V above
the supply without latching the IC. The same applies for the
C + and C – pins.
COSC Pin (16), Figure 6
The Cosc pin can be used with an external capacitor, Cosc,
connected from Pin 16 to Pin 17, to modify the internal
oscillator frequency. If Pin 16 is floating, the internal 24pF
capacitor, plus any external interpin capacitance, set the
oscillator frequency around 190kHz with ±5V supply. The
typical performance characteristics curves provide the
necessary information to set the oscillator frequency for
various power supply ranges. Pin 16 can also be driven
with an external clock to override the internal oscillator.
Although standard 7400 series CMOS gates do not
guarantee CMOS levels with the current source and sink
requirements of Pin 16, they will in reality drive the Cosc
pin. CMOS gates conforming to standard B series output
drive have the appropriate voltage levels and more than
enough output current to simultaneously drive several
LTC1043 COSC pins. The typical trip levels of the Schmitt
trigger (Figure 6) are given below.
SUPPLY
V+ = 5V,
TRIP LEVELS
V – = 0V
VH = 3.4VVL = 1.35V
V+ = 10V, V – = 0V
VH = 6.5VVL = 2.8V
V+ = 15V, V – = 0V
VH = 9.5VVL = 4.1V
12
V+ = 15V
V– = 0V
CHARGE INJECTION (pCb)
10
8
V+ = 10V
V– = 0V
6
1
OUTSIDE FOIL
4
V+ = 5V
V– = 0V
2
CS
2
3
0
0
2
4
6
10
8
VIN (V)
12
14
PRINTED CIRCUIT
BOARD AREA
16
LTC1043
LTC1043 • AI05
LTC1043 • AI04
Figure 5. Printed Circuit Board Layout
Showing Shielding the Sampling Capacitor
Figure 4. Individual Switch Charge Injection
vs Input Voltage
V+
4
38µF
COSC
16
COSC
(EXTERNAL)
TO CLK GENERATOR
24pF
17
fOSC = 190kHz •
V–
(24pF)
(24pF + COSC)
LTC1043 * AI06
Figure 6. Internal Oscillator
1043fa
7
LTC1043
U
TYPICAL APPLICATIO S
Divide by 2
Multiply by 2
Ultra Precision Voltage Inverter
1/2 LTC1043
1/2 LTC1043
VIN
1/2 LTC1043
7
8
VOUT
VOUT = VIN /2
7
7
8
VOUT = –VIN
8
VIN
1µF
11
11
11
1µF
1µF
1µF
1µF
1µF
12
12
12
VIN
13
14
13
17
16
13
14
14
16
16
17
17
0.01µF
0.01µF
0.01µF
VOUT = VIN /2 ± 1ppm
0 ≤ VIN ≤ V+
3 ≤ V+ ≤ 18V
VOUT = 2VIN ± 5ppm
0 ≤ VIN ≤ V+ /2
3 ≤ V+ ≤ 18V
LTC1043 • A01
Precision Multiply by 3
VOUT = –VIN ±2ppm
V – < VIN < V +
V + = +5V, V – = –5V
LTC1043 * A03
LTC1043 • A02
Precision Multiply by 4
Divide by 3
VIN
LTC1043
LTC1043
LTC1043
7
8
7
11
8
VIN
VIN
7
11
11
1µF
1µF
1µF
12
12
12
13
8
13
14
14
13
14
6
5
VOUT
VOUT
2VIN
5
6
2
1µF
5
6
VOUT = 4VIN
1µF
2
2
1µF
1µF
1µF
3
18
1µF
1µF
1µF
3
3
15
18
VOUT
15
18
15
1µF
16
17
0.01µF
VOUT = 3VIN ±10ppm
0 < VIN < V+/3
3V < V+ < 18V
17
16
16
LTC1043 • A04
VOUT = 4VIN ±40ppm
0 ≤ VIN ≤ V+/4
3V < V+ < 18V
17
0.01µF
0.01µF
VOUT = VIN /3 ±3ppm
0 ≤ VIN ≤ V+
LTC1043 • A05
LTC1043 • A06
1043fa
8
LTC1043
U
TYPICAL APPLICATIO S
Divide by 4
0.005% V/F Converter
–5V
VIN
7
LT1009
2.5k
1k
LTC1043
8
17
5V
1/2 LTC1043
11
8
1µF
1µF
7
1µF
12
11
fOUT: 0kHz TO 30kHz
14
13
13
14
4
VIN
0V TO 3V
VOUT
5
6
6.19k
12
5V
GAIN
2.5k
16
0.01µF
–
1µF
LF356
+
2
1µF
1µF
–5V
3
30pF
22k
18
15
16
17
330k
Q1
2N2907A
0.01µF
1µF
–5V
LTC1043 • A08
0 ≤ VIN ≤ V+
VOUT = VIN /4 ±5ppm
LTC1043 • A07
0.01% Analog Multiplier
1/4 LTC1043
14
1k
–5V
13
LT1004-1.2V
1µF
12
5V
YINPUT
7.5k*
2
1µF
–
+
†
80.6k*
0.01µF
6
16
4
XINPUT
30pF
6
2
5
–
7
LT1056
3
330k
OPERATE LTC1043 FROM ±5V
POLYSTYRENE, MOUNT CLOSE
*1% FILM RESISTOR
ADJUST OUTPUT TRIM
SO X • Y = OUTPUT ±0.01%
†
2N2907A
(FOR START-UP)
1µF
–5V
5V
1/4 LTC1043
–5V
22k
20k
OUTPUT
TRIM
7
LT1056
3
0.001µF
2
0.001µF
†
+
6
OUTPUT
XY ±0.01%
4
–5V
LTC1043 • A09
1043fa
9
LTC1043
U
TYPICAL APPLICATIO S
Voltage Controlled Current Source with
Ground Referred Input and Output
Single 5V Supply, Ultra Precision
Instrumentation Amplifier
5V
5V
+
LTC1043
7
3
8
7
+
6
LTC1052
2
4
1µF
INPUT
8
+
1/2 LT1013
OUTPUT
AV = 1000
8
–
11
3
INPUT
0V TO 2V
2
–
1
4
1
0.1µF 0.1µF
1µF
0.68µF
12
–
99.9k
100Ω
13
5V
14
1k
4
V+ = 5V
43k
5
6
8
0.22µF
7
10k
2
11
1µF
NONPOLARIZED
1µF
1N914
1µF
1µF
3
18
100Ω
12
15
14
≈ –0.5V
13
1/2 LTC1043
16
17
4
INPUT AND OUTPUT VOLTAGE RANGE INCLUDES GROUND.
INPUT REFERRED OFFSET ERRORS ARE TYPICALLY 3µV WITH
1µV OF NOISE
CMRR ~ 120dB
5V
0.0047
1OUT =
VIN
100Ω
16
17
0.001µF
LTC1043 • A10
OPERATES FROM A SINGLE 5V SUPPLY
LTC1043 • A11
Precision Instrumentation Amplifier
5V
CHOPPER
4
1/2 LTC1043
+ INPUT
6
AC AMPLIFIER
1/4 LTC1043
11
8
2
1µF
1µF
5V
1µF
7
5
PHASE
SENSITIVE
DEMODULATOR
3
1M 2
+
7
LT1056
–
1/4 LTC1043
1µF
6
13
100k
12
4
100k
2
–
100k
5V
7
LT1056
14
–5V
DC
OUTPUT AMPLIFIER
1µF
3
3
+
6
OUTPUT
4
–5V
100Ω
– INPUT
18
15
16
17
0.01µF
0.01
–5V
OFFSET = 10µV
DRIFT = 0.1µV/°C
FULL DIFFERENTIAL INPUT
CMRR = 140dB
OPEN LOOP GAIN > 10 8
GAIN = R2/R1 + 1
IBIAS = 1nA
R2
100k
R1
100Ω
LTC1043 • A12
1043fa
10
LTC1043
U
TYPICAL APPLICATIO S
Lock-In Amplifier (= Extremely Narrow-Band Amplifier)
THERMISTOR BRIDGE
IS THE SIGNAL SOURCE
SYNCHRONOUS
DEMODULATOR
10k*
10k*
T1
500Hz
SINE DRIVE
4
1
6.19k
3
3
6.19k 2
RT
5V
5V
6.19k
2
+
1/4 LTC1043
6
LT1007
–
3
12
–
5V
LM301A
13
+
2
8
1
100k
1M
–
LT1012
–5V
14
3
–5V
16
30pF
+
T1 = TF5SX17ZZ, TOROTEL
RT = YSI THERMISTOR 44006
≈ 6.19k AT 37.5°C
*MATCH 0.05%
6.19k = VISHAY S-102
OPERATE LTC1043 WITH
±5V SUPPLIES
47µF
PHASE TRIM
5V
0.002
4
–5V
+
50k
VOUT = 1000 • DC
BRIDGE SIGNAL
1µF
100Ω
0.01µF
6
5V
10k
2
7
LT1011
3
–
LOCK-IN AMPLIFIER TECHNIQUE
USED TO EXTRACT VERY SMALL
SIGNALS BURIED INTO NOISE
1k
8
+
LTC1043 • A013
4
1
–5V
ZERO CROSSING DETECTOR
50MHz Termal RMS/DC Converter
5V
5V
4
30k*
30k*
5V
1/2 LTC1043
6
3
5
8
+
10k
LT1013
2
2
1µF
1µF
1µF
3
–
18
15
0.01µF
1µF
5V
+
LT1013
100k*
301Ω*
10k
6
–
7
DC OUTPUT
0V TO 3.5V
10k
10k
10k
17
BRN
RED
N
CALIBRATION ADJUST
20k
5
16
0.01µF
300mV
10VRMS
INPUT
4
1
RED
T2
T2A
1A
GRN
T1B
T2B
*1% RESISTOR
GRN
2% ACCURACY DC 50MHZ
100:1 CREST FACTOR CAPABILITY
T1 TO T2 = YELLOW SPRINGS INST. CO.
THERMISTOR COMPOSITE
ENCLOSE T1 AND T2 IN STYROFOAM
LTC1043 • A14
1043fa
11
LTC1043
U
TYPICAL APPLICATIO S
Quad Single 5V Supply, Low Hold Step, Sample-and-Hold
5V
2
1/4 LT1014
NC
7
3
8
13
4
–
+
1
OUTPUT
1/4 LT1014
NC
11
6
14
OUTPUT
+
CL
0.01µF
2
VIN
VIN
6
9
–
1/4 LT1014
NC
12
5
CL
0.01µF
11
–
13
5
14
7
OUTPUT
1/4 LT1014
+
NC
18
10
15
CL
0.01µF
12
OUTPUT
+
VIN
HOLD
LTC1043 • A15
16
SAMPLE
8
CL
0.01µF
3
VIN
–
17
4
– 5V
FOR 1V ≤ VIN ≤ 4V, THE HOLD STEP IS ≤ 300µV
ACQUISITION TIME ~ 8 • RON CH FOR 10-BIT ACCURACY
LTC1043 • A16
Single Supply Precision Linearized Platinum RTD Signal Conditioner
250k*
(LINEARITY CORRECTION LOOP)
5V
3
10k*
+
8
1/2 LT1013
2
–
5V
2.4k
1
2.74k*
4
LT1009
2.5V
50k
ZERO
ADJUST
8.25k*
0.1µF
4
2k
1/2 LTC1043
7
0V TO 4V = 0°C TO 400°C
±0.05°C
1/2 LTC1043
8
5
5
6
+
1/2 LT1013
6
11
1µF
2
1µF
13
8.06k*
3
14
1mA
Rp
100Ω
AT 0°C
15
16
Rp = ROSEMOUNT 118MFRTD
* 1% FILM RESISTOR
TRIM SEQUENCE:
SET SENSOR TO 0°C VALUE. ADJUST ZERO FOR 0V OUT
SET SENSOR TO 100°C VALUE. ADJUST GAIN FOR 1,000V OUT
SET SENSOR TO 400°C VALUE. ADJUST LINEARITY FOR 4,000V OUT
REPEAT AS REQUIRED
5k
1µF
1µF
887Ω
12
–
7
1k
GAIN
ADJUST
18
1k*
17
0.01µF
LTC1043 • A17
1043fa
12
LTC1043
U
TYPICAL APPLICATIO S
0.005% F/V Converter
75k*
10k
GAIN TRIM
1µF
1/4 LTC1043
1k
5V
13
–5V
–
14
1µF
LT1004-1.2C
12
–5V
1000pF
FREQUENCY IN
0kHz TO 30kHz
0V TO 3V OUTPUT
LF356
+
4
5V
17
–5V
*75k = TRW # MTR-5/120ppm
16
LTC1043 • A18
High Frequency Clock Tunable Bandpass Filter
R1
10k
R2
10k
10k
RIN
VIN
5V
–
1/2 LTC1043
LT1056
7
8
+
–5V
CLOCK
INPUT
11
16
1000pF
200pF
BANDPASS
OUTPUT
12
5V
13
14
4
–
1/2 LTC1043
LT1056
RQ = 10k
5V
5
6
+
–5V
2
1000pF
200pF
3
fCLK
•
BANDPASS CENTER FREQUENCY fO =
31.4
BANDPASS GAIN AT fO IS: RQ /RIN
RQ
R2
Q=
R2
R1
fO MAX ≤ 100kHz
QMAX AT 100kHz fO IS ≤10
(fO • Q) MAX ≤ 1MHz
fCLK MAX ≤ 3MHz, Q < 2
R2
R1
5V
15
18
–
LT1056
17
–5V
+
– 5V
LTC1043 • A19
1043fa
13
LTC1043
U
TYPICAL APPLICATIO S
Frequency-Controlled Gain Amplifier
13A 1/2 LTC1043A
12A
16A
GAIN CONTROL
0kHz TO 10kHz = GAIN 0 TO 1000
13B 1/2 LTC1043B
14A
14B
12B
16B
0.01µF
100pF
11A
11B
7A
7B
8A
8B
VIN
5V
2
–
0.01µF
7
6
LT1056
3
FOR DIFFERENTIAL INPUT, GROUND PIN 8A AND USE PINS 13A AND 7A FOR INPUTS
fIN • 0.01µF
GAIN =
; GAIN IS NEGATIVE AS SHOWN
1kHz • 100pF
FOR SINGLE-ENDED INPUT AND POSITIVE GAIN, GROUND PIN 8A AND USE PIN 7A FOR INPUT
USE ± 5V SUPPLIES FOR LTC1043
+
VOUT
4
–5V
LTC1043 • A20
Relative Humidity Sensor Signal Conditioner
0.01µF
1/4 LTC1043
8
7
16
–5V
17
11
470k
100pF
1k*
500
90%
RH TRIM
5V
1/4 LTC1043
13
2
14
–
7
LT1056
3
12
1µF
+
4
–5V
1µF
6
10k
3
+
6
LM301A
2
8
–
OUTPUT
0V TO 1V = 0% TO 100%
1
LT1004
1.2V
SENSOR
9k*
22M
100pF
10k
5% RH TRIM
33k
* = 1% FILM RESISTOR
SENSOR = PANAMETRICS # RHS
≈ 500pF AT RH = 76%
1.7 pF/%RH
1k*
LTC1043 • A21
1043fa
14
LTC1043
U
TYPICAL APPLICATIO S
Linear Variable Differential Transformer (LVDT), Signal Conditioner
1/4 LTC1043
0.005µF
0.005µF
30k
7
5V
5V
30k
3
4
11
8
+
1.5kHz
1
LT1013
2
8
RD-BLUE
YEL-BLK
–
4
100k
5
– 5V
BLUE
GRN
AMPLITUDE STABLE
SINE WAVE SOURCE
6
10k
1N914
4.7k
LT1004
1.2V
Q1
2N4338
1.2k
+
1/2 LT1013
1µF
–
10µF
OUTPUT
0V ±2.5V
0M 2.50M
200k
YEL-RED
BLK
10k GAIN TRIM
LVDT
+
7
12
7.5k
–5V
17
13
14
1/4 LTC1043
LVDT = SCHAEVITZ E-100
5V
100k
5V
0.01µF
3
100k
PHASE
TRIM
1k
8
+
7
LT1011
2
TO PIN 16, LTC1043
1
–
4
–5V
LTC1043 • A22
Precision Current Sensing in Supply Rails
IIN
SHUNT CAN BE IN POSITIVE
OR NEGATIVE SUPPLY LEAD
RSHUNT
1/2 LTC1043
7
VOUT
8
11
+
1µF
1µF
12
13
14
16
17
0.01µF
LTC1043 • A23
1043fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LTC1043
U
PACKAGE DESCRIPTIO
D Package
18-Lead Side Brazed (Hermetic)
(Reference LTC DWG # 05-08-1210)
.165
(4.191)
MAX
.485
(12.319)
MAX
.020 – .060
(0.508 – 1.524)
.910
(23.114)
MAX
.005
(0.127)
MIN
17
18
16
15
14
13
12
11
10
.290
(7.366)
TYP
.008 – .015
(0.203 – 0.381)
.100
(2.54)
BSC
.125
(3.175)
MIN
.300
(7.620)
REF
PIN NO. 1
IDENT
.054
(1.372)
TYP
.015 – .023
(0.381 – 0.584)
3
2
1
4
5
7
6
8
9
D18 0801
OBSOLETE PACKAGE
N Package
18-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.900*
(22.860)
MAX
18
17
16
15
14
.130 ± .005
(3.302 ± 0.127)
.300 – .325
(7.620 – 8.255)
13
12
11
10
.045 – .065
(1.143 – 1.651)
.020
(0.508)
MIN
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
.255 ± .015*
(6.477 ± 0.381)
+.035
.325 –.015
1
2
3
5
4
6
8
7
(
9
8.255
+0.889
–0.381
.120
(3.048)
MIN
)
.005
(0.127)
MIN
.018 ± .003
(0.457 ± 0.076)
.100
(2.54)
BSC
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
N18 1002
SW Package
18-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 ±.005
.030 ±.005
TYP
.447 – .463
(11.354 – 11.760)
NOTE 4
N
18
17
16
15
14
13
12
11
10
N
.325 ±.005
.420
MIN
.394 – .419
(10.007 – 10.643)
NOTE 3
1
2
3
N/2
NOTE:
1. DIMENSIONS IN
N/2
RECOMMENDED SOLDER PAD LAYOUT
.005
(0.127)
RAD MIN
.009 – .013
(0.229 – 0.330)
.291 – .299
(7.391 – 7.595)
NOTE 4
.010 – .029 × 45°
(0.254 – 0.737)
1
3
.093 – .104
(2.362 – 2.642)
0° – 8° TYP
.050
(1.270)
BSC
NOTE 3
.016 – .050
(0.406 – 1.270)
16
2
Linear Technology Corporation
.014 – .019
(0.356 – 0.482)
TYP
4
5
6
7
8
9
.037 – .045
(0.940 – 1.143)
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES
ON THE BOTTOM OF PACKAGES ARE THE
MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR
WITHOUT ANY OF THE OPTIONS
4. THESE DIMENSIONS DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT
EXCEED .006" (0.15mm)
.004 – .012
(0.102 – 0.305)
S18 (WIDE) 0502
1043fa
LW/TP 1202 1K REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 1985