100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 1 EFFECTIVE THERMAL MANAGEMENT by knürr www.knuerr.com ® ® CoolBlast Large Airflow Volumes for optimised Heat Dissipation W NE CoolBlast® - Top-Mounting Fan 100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 2 THERMAL MANAGEMENT CoolBlast®: “Power up – Cool down!“ W NE Modularity Selection according to the required volume flow. Adaption is made specifically via fan selection according to three performance classes: • Standard Performance (axial fan) • High Performance (axial fan with high speed rate) • Ultra High Performance (diagonal fan) W NE Grid (optimised according to airflow) • With very low pressure loss, so that high cooling power of the modules is guaranteed • Contributes to considerable noise reduction (depending on design and construction) W NE Thermostat • Unit is switched on and off thermostat-controlled • Adjustable according to required temperature 2 100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 3 THERMAL MANAGEMENT CoolBlast® fan unit Strong points 1 LUF20125 The constantly increasing power losses of electronic modules make high demands on the effective cooling of electronic modules. rature is also detected in the same way. The fault signal can be connected with the rack monitoring system (RMS). Large airflow volumes ensure secured heat dissipation, whereby higher airflow speeds reach the components, which leads to better heat transfer. A simple thermostat-controlled model is also available. 4 Optimum heat dissipation of the cooled module is attained with the high airflow volumes and pressure springs in the CoolBlast® fan unit. Buildingspecific CFD simulations can optimise each customer thermal management application. 5 Air conduction components, optional with filter, round off the product range. The filter mats protect the electronic components in use from dirt build-ups and dust and can be changed during running operation. The packing density of the electronics in the racks is also increasing. Fans with high pressure jump overcome the resulting higher pressure loss. The space-saving 1 HU construction guarantees maximum installation space for our customers' equipment. 1 LUF20140 1 2 3 4 LUF20056 The CoolBlast® fan unit from Knürr is available as fan plug-in for vertical cooling of modules with 3 and 6 fans. The airflow required for cooling is primarily determined by the fan selection. Fans in three different performance classes are available (Standard, High, and Ultra High Performance). Selection can be made between quiet axial fans and special diagonal fans with an especially high support rate for cooling air. 2 To ensure that plenty of cooling air reaches the electronic components, CoolBlast® has an IP protective grid with high free cross-section surface. The grid form minimises the pressure loss of the streaming airflow and reduces the streaming noise. 3 The Knürr CoolBlast® adjusts its cooling airflow to the power loss to be cooled. The temperatureregulated control of the fan rotation optimises the noise emission and the lifespan of the fans. The maximum reference temperature is set at the front. In addition to the CoolBlast® fan unit, a number of other components and accessory parts are also available for rack thermal management. LUF20054 LUF20077 A fan failure detector ensures high operational security. Exceeding the reference tempe- 5 LUF20133 3 100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 4 THERMAL MANAGEMENT CoolBlast® fan unit Uncontrolled Approvals CE mark in accordance with the low voltage directive 73/23/EEC and EMC directive 89/366/EEC - Fan unit for vertical cooling of modules in 19” racks - Chassis rails are recommended for mounting. Chassis rails are required with CoolBlast 6-fan. LUF20125 Supply schedule 1 CoolBlast® fan unit, packed, incl. operating instructions Material Sheet steel, high-grade steel grid Only with DC devices: 1 connection cable, 2m, with connector plug and free ends Finish / Colour Housing: zinc-passivated Front panel, powder-coated, smooth in RAL 7035 light-grey Only with 230V AC devices: 1 connection cable, 2m, Schuko-plug for low voltage devices How supplied Assembled, wired and tested LUF20139 W • V (m3/h) Name W H D kg n Elec. connection dB(A)) Order no. CoolBlast 230V 3-fan 440 43.6 230 3 3 207 ... 253VAC; 50/60Hz 45 495 Pa 74 45.2 03.027.001.1 CoolBlast 230V 6-fan 440 43.6 390 6 6 207 ... 253VAC; 50/60Hz 90 990 74 48.8 03.027.002.1 CoolBlast 115V 3-fan 440 43.6 230 3 3 103.5 ... 126.5VAC; 50/60Hz 44 576 88 47.3 03.027.004.1 CoolBlast 115V 6-fan 440 43.6 390 6 6 103.5 ... 126.5VAC; 50/60Hz 88 1152 88 50.8 03.027.005.1 CoolBlast 24V 3-fan SP 440 43.6 230 2.5 3 12 ... 27VDC 23 553 68 49.6 03.027.031.1 CoolBlast 24V 6-fan SP 440 43.6 390 5 6 12 ... 27VDC 46 1106 68 53.3 03.027.032.1 CoolBlast 24V 3-fan HP 440 43.6 230 3 3 12 ... 25VDC 30 711 160 55.8 03.027.034.1 CoolBlast 24V 6-fan HP 440 43.6 390 6 6 12 ... 25VDC 60 1422 160 59.1 03.027.035.1 CoolBlast 24V 3-fan UP 440 43.6 230 3 3 16 ... 26VDC 62 825 310 61.8 03.027.037.1 CoolBlast 24V 6-fan UP 440 43.6 390 6 6 16 ... 26VDC 123 1650 310 65.1 03.027.038.1 CoolBlast 48V 3-fan SP 440 43.6 230 3 3 36 ... 55VDC 24 553 68 49.6 03.027.041.1 CoolBlast 48V 6-fan SP 440 43.6 390 6 6 36 ... 55VDC 48 1106 68 53.2 03.027.042.1 CoolBlast 48V 3-fan HP 440 43.6 230 3 3 36 ... 55VDC 54 826 160 58.6 03.027.044.1 CoolBlast 48V 6-fan HP 440 43.6 390 6 6 36 ... 55VDC 108 1652 160 62 03.027.045.1 CoolBlast 48V 3-fan UP 440 43.6 230 3 3 36 ... 53VDC 60 825 310 61.9 03.027.047.1 CoolBlast 48V 6-fan UP 440 43.6 390 6 6 36 ... 53VDC 119 1650 310 65.3 03.027.048.1 CoolBlast® fan unit Thermostat-controlled Approvals CE label in accordance with low voltage directive 73/23/EEC EMC directive 89/366/EEC - Fan unit for vertical cooling of modules in 19” racks - Fan function (ON/OFF) thermostatcontrolled, setting from 0°C to 60°C - Chassis rails are recommended for mounting. Chassis rails are required with CoolBlast 6-fan. LUF20127 Supply schedule 1 CoolBlast® fan unit, packed, incl. operating instructions Material Sheet steel, high-grade steel grid Only with DC devices: 1 connection cable, 2m, with connector plug and free ends Finish / Colour Housing: zinc-passivated Front panel, powder-coated, smooth in RAL 7035 light-grey How supplied Assembled, wired and tested LUF20138 4 Only with 230V AC devices: 1 connection cable, 2m, Schuko-plug for low voltage devices • V (m3/h) Name W H D kg n Elec. connection W Pa dB(A)) Order no. CoolBlast 230V 3-fan Thermostat 440 43.6 230 3 3 207 ... 253VAC; 50/60Hz 45 495 74 45.2 03.027.011.1 CoolBlast 230V 6-fan Thermostat 440 43.6 390 6 6 207 ... 253VAC; 50/60Hz 90 990 74 48.8 03.027.012.1 CoolBlast 115V 3-fan Thermostat 440 43.6 230 3 3 103.5 ... 126.5VAC; 50/60Hz 44 576 88 47.3 03.027.014.1 CoolBlast 115V 6-fan Thermostat 440 43.6 390 6 6 103.5 ... 126.5VAC; 50/60Hz 88 1152 88 50.8 03.027.015.1 100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 5 THERMAL MANAGEMENT CoolBlast® fan unit Speed-controlled Approvals CE label in accordance with low voltage directive 73/23/EEC EMC directive 89/366/EEC - Fan unit for vertical cooling of modules in 19” racks - Reference temperature can be set (20°C to 55°C) - Speed regulation 30% to 100%of the nominal speed, with sensor failure 100% speed - Monitoring of individual fans - Floating common alarm output for excess temperature alarm and fan failure - Optical status display for O.K., excess temperature and fan failure - Acoustic warning - Chassis rails are recommended for mounting. Chassis rails are required with CoolBlast 6-fan. LUF20128 Supply schedule 1 CoolBlast® fan unit, packed, incl. operating instructions 1 Sensor cable, 2m (plug-in) 1 Signal cable, 2m (plug-in) Only with DC devices: 1 connection cable, 2m, with connector plug and free ends Only with 230V AC devices: 1 connection cable, 2m, Schuko-plug for low voltage devices Material Sheet steel, high-grade steel grid LUF20140 How supplied Assembled, wired and tested Finish / Colour Housing: zinc-passivated Front panel, powder-coated, smooth in RAL 7035 light-grey LUF20179 W • V (m3/h) Name W H D kg n Elec. connection CoolBlast 115/230V, 3-fan controlled SP 440 43.6 230 3.2 3 100 to 253VAC; 50/60Hz 25 553 CoolBlast 115/230V, 6-fan controlled SP Pa dB(A)) Order no. 68 49.6 03.027.021.1 440 43.6 390 6.2 6 100 to 253VAC; 50/60Hz 48 1106 68 53.3 03.027.022.1 CoolBlast 115/230V, 3-fan controlled HP 440 43.6 230 3.2 3 100 to 253VAC; 50/60Hz 32 711 173 55.8 03.027.024.1 CoolBlast 115/230V, 6-fan controlled HP 440 43.6 390 6.2 6 100 to 253VAC; 50/60Hz 62 1422 173 59.1 03.027.025.1 CoolBlast 115/230V, 3-fan controlled UP 440 43.6 230 3.4 3 100 to 253VAC; 50/60Hz 64 825 310 61.8 03.027.027.1 CoolBlast 115/230V, 6-fan controlled UP 440 43.6 390 6.4 6 100 to 253VAC; 50/60Hz 125 1650 310 65.1 03.027.028.1 CoolBlast 24/48V, 3-fan controlled SP 440 43.6 230 3.1 3 20 to 60VDC 25 553 68 49.6 03.027.051.1 CoolBlast 24/48V, 6-fan controlled SP 440 43.6 390 6.1 6 20 to 60VDC 48 1106 68 53.3 03.027.052.1 CoolBlast 24/48V, 3-fan controlled HP 440 43.6 230 3.1 3 20 to 60VDC 32 711 173 55.8 03.027.054.1 CoolBlast 24/48V, 6-fan controlled HP 440 43.6 390 6.1 6 20 to 60VDC 62 1422 173 59.1 03.027.055.1 CoolBlast 24/48V, 3-fan controlled UP 440 43.6 230 3.3 3 20 to 60VDC 64 825 310 61.8 03.027.057.1 CoolBlast 24/48V, 6-fan controlled UP 440 43.6 390 6.3 6 20 to 60VDC 125 1650 310 65.1 03.027.058.1 Dimensions in mm: W = Width H = Height D = Depth h = Installation height d = Usable depth L = Length HU = Standard height of unit 1HU=66.65mm UP = Unit of packaging Kg = Weight Conversion: 1mm = 0.03937 inch = Express Item 1 kg = 2.2046 pounds SP = Standard Performance HP= High Performance UP = Ultra High Performance n W V ∆V • • = = = = Number of fans Power consumption [W] Air volume stream (m3/h) Loss of air volume stream (%) Pa l nom l max V dB[A] = = = = = Pressure increase Nominal current [A] Residual current [A]) Voltage [400V-3-phase] Sound pressure 1mm distance from the rack (600mmx600mm, raised cover) 5 100904_CoolBlast_E_f 23.08.2006 15:03 Uhr Seite 6 THERMAL MANAGEMENT CoolBlast® Airflow Routing via Front Intake Strong points The CoolBlast® “front intake unit” is specifically designed for cooling the modular chassis (heat sources). 1 LUF20148 3 The filter mat protects electronics in use against dust and dirt. It may be replaced during operation. LUF20056 MR MR MR MR MR MR MR MR LUF20136 LUF20156 2 The front panel is available as optional equipment and can be installed at a later stage. It is often used for appearance reasons. LUF20157 1 Optimised airflow routing channels warm air selectively towards the back (see figure 1), thereby avoiding the accumulative warming of vertical air streams from one module rack (MR) to the other (see figure 2). 2 3 Optimum level LUF20146 Negligible effect Optional Combinations: Order from Figure Airflow router 1 Airflow router 1 + 2 plus front panel Airflow router 6 + + Order no., 3-fan 6-fan Loss of Airflow Volume 3-fan 6-fan 03.027.094.1 03.027.095.1 30 % 45 % 03.027.094.1 03.027.095.1 40 % 55 % 03.027.097.1 03.027.097.1 50 % 60 % 03.027.094.1 03.027.095.1 plus front panel 03.027.097.1 03.027.097.1 and filter 03.027.098.1 03.027.099.1 1 2 3 100904_CoolBlast_E_f 23.08.2006 15:04 Uhr Seite 7 THERMAL MANAGEMENT Airflow Router for Front Intake, 1 HU CoolBlast® Finish / Colour Powder-coated RAL 7035, light-grey textured - For fan insert CoolBlast® 3-fan and 6-fan and front intake - Used as air baffle - Upgradeable with front panel and filter mat Supply schedule 1 airflow router Material Sheet steel LUF20131 D How supplied By unit W H Design Order no. UP 19” 43.6 230 For 3-fan 03.027.094.1 1 Set 19” 43.6 390 For 6-fan 03.027.095.1 1 Set LUF20142 Front Panel for Airflow Router and Front Intake, 1 HU CoolBlast® Supply schedule 1 Front panel - Use in combination with vent airflow for front intake - Later mounting optional How supplied By unit Material Sheet steel Finish / Colour Powder-coated RAL 7035 Light-grey, smooth LUF20136 W H 19” 43.6 D Design Order no. UP 03.027.097.1 1 Set Filter Unit for Front Intake CoolBlast® Supply schedule 1 Filter - Use in combination with vent airflow for front intake - Later mounting and/or filter replacement during operation optional How supplied By unit Filter class G2 LUF20135 Material Viledon K15/150 D Design Order no. UP 400 W H 160 For 3-fan 03.027.098.1 1 Set 400 320 For 6-fan 03.027.099.1 1 Set 7 100904_CoolBlast_E_f 23.08.2006 15:04 Uhr Seite 8 THERMAL MANAGEMENT 19” Plug-in Filter Unit, 1 HU Finish / Colour Housing: powder-coated - RAL 9011 black textured Front panel: RAL 7035 - Light-grey Handle: powder-coated RAL 5008, grey-blue textured - Suitable for use with plug-in fan unit CoolBlast® - Adjusted to the respective depth of insertion Material Housing: sheet steel Front panel: ABS (UL94 V-0) Handle: extruded aluminium profile Filter: Viledon P 15/150 LUF00205 Supply schedule 1 Plug-in filter unit 1 Filter Filter class G2 How supplied By unit W H Order no. Up 19” 43.6 282 D 2.0 kg W n Design 03.025.250.1 1 Set 19” 43.6 660 4.0 03.025.253.1 1 Set Replacement Filter Unit Supply schedule 1 Filter unit - For 19” plug-in filter Material Filter: Viledon P 15/150 How supplied By unit Filter class G2 LUF00280 8 W H Order no. Up 282 D kg W n Design 03.025.246.9 1 Set 660 03.025.249.9 1 Set 100904_CoolBlast_E_f 23.08.2006 15:04 Uhr Seite 9 THERMAL MANAGEMENT CoolBlast® Filter Units: Technical Data Item Number Dimensions L x W x H CoolBlast® CoolBlast® CoolBlast® CoolBlast® 01.914.070.9 01.914.075.9 01.914.090.9 01.914.071.9 119 x 119 x 38 119 x 119 x 38 119 x 119 x 38 119 x 119 x 38 184.2 m3/h 237 m3/h 275 m3/h 184.2 m3/h 24 VDC 24 VDC 24 VDC 48 VDC Max. Volume flow Free blowing Voltage Frequency Power consumption 7,4 W 11 W 20,5 W 7,7 W Noise free-blowing 43 dB(A) 59 dB(A) 60 dB(A) 43 dB(A) Bearing system Ball bearing Ball bearing Ball bearing Ball bearing Nominal rotation speed 2950 min-1 4400 min-1 6000 min-1 2950 min-1 Ambient temperature -10 °C to +70 °C -30 °C to +55 °C -20 °C to +65 °C -10 °C to +70 °C Life-span L 10 at 40˚C 75,000 h 70,000 h 70,000 h 75,000 h Approvals CE, VDE CE, VDE CE, VDE CE, VDE 03.027.031.1 03.027.034.1 03.027.037.1 03.027.041.1 03.027.032.1 03.027.035.1 03.027.038.1 03.027.042.1 03.027.021.1 03.027.024.1 03.027.027.1 03.027.022.1 03.027.025.1 03.027.028.1 03.027.051.1 03.027.054.1 03.027.057.1 03.027.052.1 03.027.055.1 03.027.058.1 CoolBlast® CoolBlast® CoolBlast® permissible. Insert into CoolBlast®: Item Number Dimensions L x W x H CoolBlast® 01.914.076.9 01.914.091.9 01.914.050.9 01.914.051.9 119 x 119 x 38 119 x 119 x 38 119 x 119 x 38 119 x 119 x 38 275.4 m3/h 275 m3/h 192 m3/h 165 m3/h 48 VDC 48 VDC 115 VAC 230 VAC 50 Hz 50 Hz Max. Volume flow Free blowing Voltage Frequency Power consumption 17,8 W 19,7 W 14,5 W 15 W Noise free-blowing 57 dB(A) 60 dB(A) 41 dB(A) 38 dB(A) Bearing system Ball bearing Ball bearing Ball bearing Ball bearing Nominal rotation speed 4200 min-1 6000 min-1 2900 min-1 2600 min-1 Ambient temperature -10 °C to +70 °C -20 °C to +65 °C -40 °C to +60 °C -40 °C to +60 °C Life-span L 10 at 40˚C 105,000 h 70,000 h 43,500 h 43,500 h CE, VDE CE, VDE CE, VDE CE, VDE 03.027.044.1 03.027.047.1 03.027.004.1 03.027.001.1 03.027.045.1 03.027.048.1 03.027.005.1 03.027.002.1 03.027.014.1 03.027.011.1 03.027.015.1 03.027.012.1 permissible. Approvals Insert into CoolBlast®: 9 100904_CoolBlast_E_f 23.08.2006 15:04 Uhr Seite 10 THERMAL MANAGEMENT New: CoolBlast ® Top-Mounting Fan 10 100904_CoolBlast_E_f 23.08.2006 15:04 Uhr Seite 11 THERMAL MANAGEMENT CoolBlast® Top-Mounting Fan Strong points 1 1 3 An optional ventilation dome or optional filters (see chart) avoid the intrusion of dust if a fan is not active. 4 The CoolBlast® top-mounting fan and its recently developed protective grid minimize the air streams’ pressure loss and reduce airflow noises. The CoolBlast® top-mounting fan is a system with a notably low noise level. LUF20124 2 2 The ever-increasing dissipation loss of electronic components continues to increase the thermal load within the rack. CoolBlast® features a modular structure that offers the right solution for any thermal load. The CoolBlast® top-mounting fan from Knürr is therefore available in different designs with two, three or six fans. The product range contains controlled, thermostat-controlled and uncontrolled model types. LUF20162 Cable entry Fan top Fan unit 3 LUF20121 LUF20175 Optional combinations: Order form 4 LUF20124 Top-mounting fan Checklist for installation into miracle Chart 1. What is the rack’s width and depth? 1 2. Fan unit with 2, 3 or 6 fans? 3. What is the required supply voltage? 4. What is the target flow rate? Top-mounting fan 5. What pressure is there? plus CoolBlast® 6. CoolBlast® with or without controls and/or thermostat controlled design? 7. Is it the right network cable? Top-mounting fan plus filter 1 + 2 + 3 8. Do you require particular protection from particles (ventilation dome and / or filter)? 11 100904_CoolBlast_E_f 23.08.2006 15:05 Uhr Seite 12 THERMAL MANAGEMENT CoolBlast® Top-Mounting Fan Supply schedule 1 CoolBlast® fan unit 1 Network cable, 3m, with shock-proof plug (230 VAC) Accessories for assembly Operating instructions - DC model types and designs for 115 VAC upon request (see CoolBlast® fan plug-ins) Material Housing: sheet steel, stainless steel grid Front panel: sheet steel How supplied Assembled, wired and tested Finish / Colour Housing: zinc-passivated Front panel (only controlled designs): Powder-coated RAL 7035 Light-grey textured LUF20160 Note Please order specific mains cable (see page 15) extra! Cable entry Fan top LUF20161 Fan unit LUF20175 LUF20124 Name Design CoolBlastT 230V 2-fan Electrical connection 207...253VAC; 50/60 Hz 30 • V (m3/h) ∆P(Pa) 330 74 p(dB(A)) Order No. UP 43.4 03.027.300.1 1 Set CoolBlastT 230V 3-fan 207...253VAC; 50/60 Hz 45 495 74 45.2 03.027.301.1 1 Set CoolBlastT 230V 6-fan 207...253VAC; 50/60 Hz 90 990 74 48.8 03.027.302.1 1 Set CoolBlastT 230V 2-fan Thermostat 207...253VAC; 50/60 Hz 30 330 74 43.4 03.027.310.1 1 Set CoolBlastT 230V 3-fan Thermostat 207...253 VAC; 50/60 Hz 45 495 74 45.2 03.027.311.1 1 Set CoolBlastT 230V 6-fan Thermostat 207...253 VAC; 50/60 Hz 90 990 74 48.8 03.027.312.1 1 Set CoolBlastT 230V 3-fan Controlled SP 100...253 VAC; 50/60 Hz 25 553 68 49.6 03.027.321.1 1 Set CoolBlastT 230V 6-fan Controlled SP 100...253 VAC; 50/60 Hz 48 1106 68 53.3 03.027.322.1 1 Set CoolBlastT 230V 3-fan Controlled HP 100...253 VAC; 50/60 Hz 32 711 173 55.8 03.027.324.1 1 Set CoolBlastT 230V 6-fan Controlled HP 100...253 VAC; 50/60 Hz 62 1422 173 59.1 03.027.325.1 1 Set CoolBlastT 230V 3-fan Controlled UP 100...253 VAC; 50/60 Hz 64 825 310 61.8 03.027.327.1 1 Set CoolBlastT 230V 6-fan Controlled UP 100...253 VAC; 50/60 Hz 125 1650 310 65.1 03.027.328.1 1 Set Dimensions in mm: W = Width H = Height D = Depth h = Installation height d = Usable depth L = Length Conversion: 12 P(W) 1mm = 0.03937 inch HU = Standard height of unit 1HU=66.65mm UP = Unit of packaging Kg = Weight = Express Item 1 kg = 2.2046 pounds SP = Standard Performance HP= High Performance UP = Ultra High Performance n W V ∆V • • = = = = Number of fans Power consumption [W] Air volume stream (m3/h) Loss of air volume stream (%) Pa l nom l max V dB[A] = = = = = Pressure increase Nominal current [A] Residual current [A]) Voltage [400V-3-phase] Sound pressure 1mm distance from the rack (600mmx600mm, raised cover) 100904_CoolBlast_E_f 23.08.2006 15:05 Uhr Seite 13 THERMAL MANAGEMENT Top Cover for CoolBlast® - For use in combination with CoolBlast® fan unit - Suitable for installation into miracle - With cable entry point (sliding panel) - Two-piece cover for subsequent assembly or service Supply schedule 1 fan roof with cable entry (three-part sliding section, can be completely opened) 2 covers Accessories for assembly Material Sheet steel LUF20163 How supplied Pre-assembled Finish / Colour Final digit of order number .1: - Powder-coated RAL 7035 - Light-grey textured Final digit of order number .8: - Powder-coated RAL 7021 -Black grey textured Fan top Covers LUF20176 (Without fan) LUF20169 W H 600 D 600 Design Order No. UP For 2- or 3-fans 01.149.031.X 1 unit 700 600 For 2- or 3-fans 01.149.041.X 1 unit 800 600 For 2- or 3-fans 01.149.051.X 1 unit 600 800 For 2-/3-or 6-fans 01.149.033.X 1 unit 700 800 For 2-/3-or 6-fans 01.149.043.X 1 unit 800 800 For 2-/3-or 6-fans 01.149.053.X 1 unit 600 900 For 2-/3-or 6-fans 01.149.034.X 1 unit 700 900 For 2-/3-or 6-fans 01.149.044.X 1 unit 800 900 For 2-/3-or 6-fans 01.149.054.X 1 unit 600 1000 For 2-/3-or 6-fans 01.149.035.X 1 unit 700 1000 For 2-/3-or 6-fans 01.149.045.X 1 unit 800 1000 For 2-/3-or 6-fans 01.149.055.X 1 unit 600 1200 For 2-/3-or 6-fans 01.149.037.X 1 unit 800 1200 For 2-/3-or 6-fans 01.149.057.X 1 unit Dust and Particle Protection for CoolBlast® Solution no. 1: Filter mat LUF20121 - For use in combination with CoolBlast® roof mounted fan - Simple filter cover protecting against the intrusion of dust when fan is not active (controlled or thermostat-controlled design) - For all roof sizes; filter and adhesive velcro tape may be cut to fit the required dimensions W H D kg Material Viledon (Filter Class G2) Supply schedule 1 Filter Adhesive velcro tape How supplied By set Design Order No. UP Fan units, 2, 3 01.149.101.9 1 Set or 6 fans LUF20168 13 100904_CoolBlast_E_f 23.08.2006 15:05 Uhr Seite 14 THERMAL MANAGEMENT Dust and Particle Protection for CoolBlast® Solution no. 2: Ventilation dome - For use in combination with CoolBlast® roof mounted fan - Closed top cover with cable entry point for protection against contaminants and dust - Mounted on spacers on the standard top cover Material Sheet steel Finish / Colour Final digit of order number .1: - Powder-coated RAL 7035 - Light-grey textured Final digit of order number .8: - Powder-coated t RAL 7021 - Dark-grey textured Supply schedule 1 cover with cable entry point Accessories for assembly LUF20174 How supplied By set W 600 LUF20172 H D 600 Design Order No. UP With cable entry point 01.149.031.X 1 Set 700 600 With cable entry point 01.149.041.X 1 Set 800 600 With cable entry point 01.149.051.X 1 Set 600 800 With cable entry point 01.149.033.X 1 Set 700 800 With cable entry point 01.149.043.X 1 Set 800 800 With cable entry point 01.149.053.X 1 Set 600 900 With cable entry point 01.149.034.X 1 Set 700 900 With cable entry point 01.149.044.X 1 Set 800 900 With cable entry point 01.149.054.X 1 Set 600 1000 With cable entry point 01.149.035.X 1 Set 700 1000 With cable entry point 01.149.045.X 1 Set 800 1000 With cable entry point 01.149.055.X 1 Set 600 600 Closed 01.130.690.X 1 Set 700 600 Closed 01.130.694.X 1 Set 800 600 Closed 01.130.691.X 1 Set 600 800 Closed 01.130.691.X 1 Set 700 800 Closed 01.130.695.X 1 Set 800 800 Closed 01.130.699.X 1 Set 600 900 Closed 01.130.692.X 1 Set 700 900 Closed 01.130.696.X 1 Set 800 900 Closed 01.130.700.X 1 Set 600 1000 Closed 01.127.700.X 1 Set 700 1000 Closed 01.127.701.X 1 Set 800 1000 Closed 01.127.702.X 1 Set Additional fan top as protection from particles, with spacers Additional top (closed) as protection from particles, with spacers Fan top Fan top Fan unit LUF20177 14 LUF20178 100904_CoolBlast_E_f 23.08.2006 15:05 Uhr Seite 15 THERMAL MANAGEMENT Mains Cable for Euro Sockets DIN 49 440 and French/Belgian Standard Mains voltage 250 VAC - Mains plug: CEE/VII - Euro socket IEC 320 - Cable: conduction H05VV-F 3G 1 mm2 Nominal current 10 A L DOS00076 Order No. UP 2000 S n F1 F2 19” safe Design 04.000.054.9 1 Set 5000 04.000.050.9 1 Set Mains Cable for Euro Sockets Swiss Standard Mains voltage 250 VAC - Mains plug: type 12 - Euro socket IEC 320 - Cable: conduction H05VV-F 3G 1 mm2 Nominal current 10 A L DOS00077 S n F1 F2 19” safe Design 2000 Order No. UP 04.000.055.9 1 Set Mains Cable for Euro Sockets British Standard Mains voltage 250 VAC - Mains plug: type BS 1363 - Euro socket IEC 320 - Cable: conduction H05VV-F 3G 1mm2 Nominal current 10 A L DOS00078 S n F1 F2 19” safe Design 2000 Order No. UP 04.000.056.9 1 Set Euro Socket Connection Cable Mains voltage EU: 250 VAC USA: 125 VAC - Mains plug: IEC 320 - Euro socket IEC 320 - Cable: EU: H05VV-F 3G 1 mm2 USA: SJT AWG18 Nominal current 10 A DOS00519 Design Order No. UP 900 L S n F1 F2 19” safe EU 04.000.051.9 1 Set 990 USA 04.000.052.9 1 Set 15 100904_CoolBlast_E_f 23.08.2006 15:05 Uhr Seite 16 World-wide Australia Norway Tel. +61 (0) 2 96 66 - 48 66 Fax +61 (0) 2 96 66 - 48 68 Tel. +47 ( ) 64 83 84 40 Fax +47 ( ) 64 83 84 50 Austria Poland Tel. +43 (0) 1 - 9 70 22 - 0 Fax +43 (0) 1 - 9 70 22 - 29 Tel. +48 (22) 6 76 94 62 Fax +48 (22) 6 76 98 10 Belgium Portugal Tel. +32 (0) 3 - 450 7777 Fax +31 (0) 76 - 542 1015 Tel. +351 (21) 3 22 41 63 Fax +351 (21) 3 22 41 69 Brazil Russia Tel. +55 (0) 15 - 3263 - 2444 Fax +55 (0) 15 - 3263 - 1024 Tel. +7 (095) - 517 88 39 Tel. +7 (812) - 783 55 08 China Russia UNI Tel. +86 (0) 10 62 38 58 28 Fax +86 (0) 10 62 38 58 29 Tel. +7 (095) - 780 95 55 Fax +7 (095) - 780 95 56 Czech Republic Russia ICS Tel. +420 (0) 595 691 192 Fax +420 (0) 595 691 199 Tel. +7 (095) - 755 68 19 Fax +7 (095) - 913 99 87 Czech Republic Russia OCS Tel. +420 (0) 737 211 711 Tel. +7 (095) - 995 25 75 Tel. +7 (812) - 324 28 70 Denmark Singapore Tel. +45 (0) 44 85 04 85 Fax +45 (0) 44 94 99 89 Tel. +65 ( ) 67 73 - 1583 Fax +65 ( ) 67 73 - 1582 Finland Slovakia Tel. +358 (0) 19 - 8711 1 Fax +358 (0) 19 - 8711 500 Tel. +421 (0) 2 - 64 28 78 81 Fax +421 (0) 2 - 64 28 78 91 France Spain Tel. +33 (0) 1 43 77 85 85 Fax +33 (0) 1 43 39 02 10 Tel. +34 91 - 8 89 89 61 Fax +34 91 - 8 89 84 92 Greece Sweden Tel. +30 2310 - 50 04 43 Fax +30 2310 - 52 59 82 Tel. +46 (0) 8 - 59 47 07 50 Fax +46 (0) 8 - 59 47 07 69 Hong Kong Regional Sales Offices Sweden LBW Hamburg Tel. +852 28 51 22 11 Fax +852 28 51 20 60 Tel. +46 (0) 8 - 58 41 08 80 Fax +46 (0) 8 - 58 02 67 69 Tel. +49 (0) 41 01 / 40 01-0 Fax +49 (0) 41 01 / 40 01-99 Hungary Switzerland Cologne Tel. +36 (0) 1 4 21 - 30 08 Fax +36 (0) 1 4 21 - 30 00 Tel. +41 (0) 44 806 54 54 Fax +41 (0) 44 806 54 64 Tel. +49 (0) 22 36 / 89 00-0 Fax +49 (0) 22 36 / 89 00-99 India Taiwan Leipzig Tel. +91 (0) 802 - 3 38 03 47 Fax +91 (0) 802 - 34 05 65 Tel. +886 (0) 2 - 2276 - 10 19 Fax +886 (0) 2 - 2279 - 88 83 Tel. +49 (0) 3 41 / 2 45 15-0 Fax +49 (0) 3 41 / 2 45 15-99 Israel United Arab Emirates Munich Tel. +972 (0) 9 - 892 44 44 Fax +972 (0) 9 - 892 44 55 Tel. +971 (0) 4 - 335 29 95 Fax +971 (0) 4 - 334 99 51 Tel. +49 (0) 89 - 4 20 04-200 Fax +49 (0) 89 - 4 20 04-199 Italy United Kingdom Stuttgart Tel. +390 (0) 2 95 34 30 80 Fax +390 (0) 2 95 34 31 04 Tel. +44 (0) 1480 49 61 25 Fax +44 (0) 1480 49 63 73 Tel. +49 (0) 71 52 / 93 67-0 Fax +49 (0) 71 52 / 93 67-99 Japan USA Tel. +81 (0) 4 26 - 56 - 58 11 Fax +81 (0) 4 26 - 56 - 58 08 Tel. +1 (805) 534 - 28 40 Fax +1 (805) 534 - 28 41 Netherlands Tel. +31 (0) 76 - 54 22 92 2 Fax +31 (0) 76 - 54 21 01 5 www.knuerr.com Knürr AG Global Headquarters Mariakirchener Straße 38 94424 Arnstorf • Germany Tel. +49 (0) 87 23 / 27 - 0 Fax +49 (0) 87 23 / 27 - 154 www.knuerr.com 09.997.677.9 • II 10GG306 • Printed in Germany • Idea, Graphics, Editorial: Gropp/Huber • Subject to technical changes, errors and omissions. … and close to the customer!