EZ-BLE™ PSOC® EVALUATION BOARD CYBLE-014008-EVAL The EZ-BLE™ PSoC® Evaluation Board (CYBLE-014008-EVAL) enables you to evaluate and develop applications on the EZ-BLE PSoC Module (CYBLE-014008-00). The EZ-BLE PSoC Module is a fully-integrated, fully-certified, 11 mm x 11 mm x 1.8 mm, programmable, Bluetooth® Smart module designed to reduce your time-to-market. For more information visit: www.cypress.com/EZ-BLEModule - The EZ-BLE Module home page. www.cypress.com/EZ-BLEEval - The EZ-BLE PSoC Evaluation Board kit page. www.cypress.com/go/AN96841 - The getting started guide. EZ-BLE PSOC Module J6 Header GND VDD P3_6 P3_7 P3_4 P3_5 P3_2 P3_3 P3_0 P3_1 J1 Header (Bottom Side) J2 Header (Bottom Side) P0_5 P0_4 P1_0 VREF P1_2 P1_1 P0_6 P1_4 P0_7 P1_3 XRES P1_5 GND VDD P2_6 P2_4 P2_2 P0_1 VDDR P3_5 P2_5 P2_3 P2_1 GND J5 Header J4 MiniProg3 10-Pin Programming Header J3 Header VDDA VDD VDDR VDD Fig 1: CYBLE-014008-00-EVAL Pinout Description Note: To use the CYBLE-014008-EVAL you must separately purchase either the CY8CKIT-002 MINIPROG3 or the CY8CKIT-042-BLE BLE PIONEER KIT. EZ-BLETM PSOC® EVALUATION BOARD 1: Connect the CYBLE-014008-00-EVAL to the CY8CKIT-002 (MiniProg3) Connect a jumper on the J3 and J5 headers Connect the MiniProg3 to the J4 10-pin header J3 J4 J5 Fig 2: J3 and J5 Headers Fig 3: Programming/Debugging with MiniProg3 OR Plug the CYBLE-014008-EVAL on the CY8CKIT-042-BLE baseboard. Note: Jumpers on CYBLE-014008-EVAL’s J3 or J5 headers can be connected or disconnected. Fig 4: Programming and debugging with CY8CKIT-042-BLE BLE Pioneer Kit Baseboard Pin Mapping between CY8CKIT-042-BLE (Base) and CYBLE-014008-00 EVAL (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) GND GND P0_7 P0_7 P2_1 P2_1 P3_1 P3_1 VDD P1_0 P1_0 P2_2 P2_2 P3_2 P3_2 VDDR VDDR P1_1 P2_3 P2_3 P3_3 P3_3 XRES XRES P1_1 P1_2 P1_2 P2_4 P2_4 P3_4 P3_4 VREF VREF P1_3 P1_3 P2_5 P3_51 P3_7 VDDD, VDDA P0_4 P0_4 P1_4 P1_4 P2_5 P2_6 P2_6 P3_51 P3_6 P0_5 P0_5 P1_5 P1_5 P2_71 P3_51 P3_7 P0_6 P0_6 P2_0 P0_1 P3_0 P3_0 P3_6 1 The J6 header provides flexibility to route P3_5 of the EZ-BLE Module to the P2_7 and/or P3_5 connections of the Pioneer Baseboard. 2: Create a project using the CYBLE-014008-00 MPN and program/debug using PSoC® Creator™ 3.3 The EZ-BLE PSoC Module is qualified for the Bluetooth 4.1 specification and is certified for the 2.4 GHz unlicensed frequency range in USA (FCC), Canada (IC), Europe (CE), Japan (TELEC) and Korea (KC). Visit www.cypress.com/go/support for technical support © 2015 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-03253 Rev.*B