Download dac8563.pdf

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
DACxx6x Dual 16-, 14-, 12-Bit, Low-Power, Buffered, Voltage-Output
DACs With 2.5-V, 4-PPM/°C Internal Reference
1 Features
3 Description
•
The DAC756x, DAC816x, and DAC856x devices are
low-power, voltage-output, dual-channel, 16-, 14-,
and 12-bit digital-to-analog converters (DACs),
respectively. These devices include a 2.5-V,
4-ppm/°C internal reference, giving a full-scale output
voltage range of 2.5 V or 5 V. The internal reference
has an initial accuracy of ±5 mV and can source or
sink up to 20 mA at the VREFIN/VREFOUT pin.
1
•
•
•
•
•
•
•
•
•
•
Relative Accuracy:
– DAC756x (12-Bit): 0.3 LSB INL
– DAC816x (14-Bit): 1 LSB INL
– DAC856x (16-Bit): 4 LSB INL
Glitch Impulse: 0.1 nV-s
Bidirectional Reference: Input or 2.5-V Output
– Output Disabled by Default
– ±5-mV Initial Accuracy (Max)
– 4-ppm°C Temperature Drift (Typ)
– 10-ppm/°C Temperature Drift (Max)
– 20-mA Sink and Source Capability
Power-On Reset to Zero Scale or Mid-Scale
Low-Power: 4 mW (Typ, 5-V AVDD, Including
Internal Reference Current)
Wide Power-Supply Range: 2.7 V to 5.5 V
50-MHz SPI With Schmitt-Triggered Inputs
LDAC and CLR Functions
Output Buffer With Rail-to-Rail Operation
Packages: WSON-10 (3 mm × 3 mm), VSSOP-10
Temperature Range: –40°C to 125°C
2 Applications
•
•
•
•
•
•
Portable Instrumentation
PLC Analog Output Module
Closed-Loop Servo Control
Voltage Controlled Oscillator Tuning
Data Acquisition Systems
Programmable Gain and Offset Adjustment
These devices are monotonic, providing excellent
linearity and minimizing undesired code-to-code
transient voltages (glitch). They use a versatile threewire serial interface that operates at clock rates up to
50 MHz. The interface is compatible with standard
SPI™, QSPI™, Microwire, and digital signal
processor (DSP) interfaces. The DACxx62 devices
incorporate a power-on-reset circuit that ensures the
DAC output powers up and remains at zero scale
until a valid code is written to the device, whereas the
DACxx63 devices similarly power up at mid-scale.
These devices contain a power-down feature that
reduces current consumption to typically 550 nA at
5 V. The low power consumption, internal reference,
and small footprint make these devices ideal for
portable, battery-operated equipment.
The DACxx62 devices are drop-in and functioncompatible with each other, as are the DACxx63
devices. The entire family is available in MSOP-10
and SON-10 packages.
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
DAC8562
DAC8162
VSSOP (10),
WSON (10)
3.00 mm × 3.00 mm
DAC7562
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Block Diagram
GND
AVDD
DIN
SCLK
SYNC
LDAC
CLR
Buffer Control
Register Control
Input Control Logic
Control Logic
DAC756x (12-Bit)
DAC816x (14-Bit)
DAC856x (16-Bit)
VREFIN/VREFOUT
2.5-V
Reference
PowerDown
Control
Logic
Data Buffer B
DAC Register B
DAC
VOUTB
Data Buffer A
DAC Register A
DAC
VOUTA
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
7.1
7.2
7.3
7.4
7.5
7.6
7.7
8
1
1
1
2
3
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings ............................................................ 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 5
Electrical Characteristics........................................... 6
Timing Requirements ................................................ 9
Typical Characteristics ............................................ 10
Detailed Description ............................................ 28
8.1 Overview ................................................................. 28
8.2 Functional Block Diagram ....................................... 28
8.3 Feature Description................................................. 28
8.4 Device Functional Modes........................................ 32
8.5 Programming........................................................... 36
9
Application and Implementation ........................ 39
9.1 Application Information............................................ 39
9.2 Typical Applications ................................................ 41
9.3 System Examples ................................................... 45
10 Power Supply Recommendations ..................... 46
11 Layout................................................................... 46
11.1 Layout Guidelines ................................................. 46
11.2 Layout Example .................................................... 47
12 Device and Documentation Support ................. 48
12.1
12.2
12.3
12.4
12.5
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
48
48
48
48
48
13 Mechanical, Packaging, and Orderable
Information ........................................................... 48
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (August 2012) to Revision E
Page
•
Changed all instances of glitch energy in the data sheet to glitch impulse............................................................................ 1
•
Changed Applications list ...................................................................................................................................................... 1
•
Revised the Device Comparison Table ................................................................................................................................. 3
•
Added an I/O column to the Pin Functions table ................................................................................................................... 4
•
Added storage temperature to the Absolute Maximum Ratings table ................................................................................... 5
•
Added ESD Ratings table to the data sheet........................................................................................................................... 5
•
Added Recommended Operating Conditions table to the data sheet .................................................................................... 5
•
Deleted several notes following the Thermal Information table.............................................................................................. 5
•
Replaced the previous typical application ............................................................................................................................ 41
Changes from Revision C (June 2011, first official release) to Revision D
Page
•
Replaced text "QFN" with "SON" (name change only, package and orderable did not change) .......................................... 1
•
Typical power-down current consumption changed from 10 nA to 550 nA............................................................................ 1
•
Changed power requirements specifications.......................................................................................................................... 8
•
Power-down current vs Temperature typical characteristic plot updated, AVDD = 5.5 V...................................................... 16
•
Power-down current vs Power-supply voltage typical characteristic plot updated............................................................... 16
•
Added Power-On Reset (POR) Levels section .................................................................................................................... 31
2
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
5 Device Comparison Table
DEVICE
DAC7562
DAC7563
DAC8162
DAC8163
DAC8562
DAC8563
MAXIMUM RELATIVE
ACCURACY (LSB)
MAXIMUM
DIFFERENTIAL
NONLINEARITY (LSB)
MAXIMUM REFERENCE
DRIFT (ppm/°C)
±0.75
±0.25
10
±3
±0.5
10
±12
±1
10
Copyright © 2010–2015, Texas Instruments Incorporated
RESET TO
Zero
Mid-scale
Zero
Mid-scale
Zero
Mid-scale
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
3
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
6 Pin Configuration and Functions
10-Pin VSSOP
DGS Package
(Top View)
10-Pin WSON With Thermal Pad
DSC Package
(Top View)
VREFIN/VREFOUT
VOUTA
1
9
AVDD
VOUTB
2
3
8
DIN
LDAC
4
7
SCLK
CLR
5
6
SYNC
VOUTA
1
10
VOUTB
2
GND
(1)
10
(1)
VREFIN/VREFOUT
9
AVDD
8
DIN
GND
3
LDAC
4
7
SCLK
CLR
5
6
SYNC
Thermal Pad
TI recommends connecting the thermal pad to the ground plane for better thermal dissipation.
Pin Functions
PIN
NAME
NO.
I/O
DESCRIPTION
AVDD
9
I
Power-supply input, 2.7 V to 5.5 V
CLR
5
I
Asynchronous clear input. The CLR input is falling-edge sensitive. On activation of CLR, zero
scale (DACxx62) or mid-scale (DACxx63) is loaded to all input and DAC registers. This sets the
DAC output voltages accordingly. The device exits clear code mode on the 24th falling edge of the
next write to the device. Activating CLR during a write sequence aborts the write.
DIN
8
I
Serial data input. Data are clocked into the 24-bit input shift register on each falling edge of the
serial clock input. Schmitt-trigger logic input
GND
3
—
Ground reference point for all circuitry on the device
LDAC
4
I
In synchronous mode, data update occurs with the falling edge of the 24th SCLK cycle, which
follows a falling edge of SYNC. Such synchronous updates do not require the LDAC, which must
be connected to GND permanently or asserted and held low before sending commands to the
device.
In asynchronous mode, the LDAC pin is used as a negative edge-triggered timing signal for
simultaneous DAC updates. Multiple single-channel commands can be written in order to set
different channel buffers to desired values and then make a falling edge on the LDAC pin to
update the DAC output registers simultaneously.
SCLK
7
I
Serial clock input. Data can be transferred at rates up to 50 MHz. Schmitt-trigger logic input
SYNC
6
I
Level-triggered control input (active-low). This input is the frame synchronization signal for the
input data. When SYNC goes low, it enables the input shift register, and data are sampled on
subsequent falling clock edges. The DAC output updates following the 24th clock falling edge. If
SYNC is taken high before the 23rd clock edge, the rising edge of SYNC acts as an interrupt, and
the write sequence is ignored by the DAC756x, DAC816x, and DAC856x devices. Schmitt-trigger
logic input
VOUTA
1
O
Analog output voltage from DAC-A
VOUTB
2
O
Analog output voltage from DAC-B
VREFIN/VREFOUT
10
I/O
Bidirectional voltage reference pin. If internal reference is used, 2.5-V output.
4
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
7 Specifications
7.1 Absolute Maximum Ratings (1)
Over operating ambient temperature range (unless otherwise noted).
MIN
MAX
AVDD to GND
–0.3
6
V
CLR, DIN, LDAC, SCLK and SYNC input voltage to GND
–0.3
AVDD + 0.3
V
VOUT[A, B] to GND
–0.3
AVDD + 0.3
V
VREFIN/VREFOUT to GND
–0.3
AVDD + 0.3
V
Operating temperature range
–40
125
°C
150
°C
150
°C
Junction temperature, TJ
Storage temperature, Tstg
(1)
–65
UNIT
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±1000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating ambient temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
POWER SUPPLY
Supply voltage
AVDD to GND
2.7
5.5
V
0
AVDD
V
0
AVDD
V
–40
125
°C
DIGITAL INPUTS
Digital input voltage
CLR, DIN, LDAC, SCLK and SYNC
REFERENCE INPUT
VREFIN
Reference input voltage
TEMPERATURE RANGE
TA
Operating ambient temperature
7.4 Thermal Information
DAC756x, DAC816x, DAC856x
THERMAL METRIC
DSC (WSON)
DGS (VSSOP)
10 PINS
10 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
62.8
173.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
44.3
48.5
°C/W
RθJB
Junction-to-board thermal resistance
26.5
79.9
°C/W
ψJT
Junction-to-top characterization parameter
0.4
1.7
°C/W
ψJB
Junction-to-board characterization parameter
25.5
68.4
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
46.2
N/A
°C/W
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
5
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
7.5 Electrical Characteristics
At AVDD = 2.7 V to 5.5 V and TA = –40°C to 125°C (unless otherwise noted).
PARAMETER
STATIC PERFORMANCE
TEST CONDITIONS
MIN
Resolution
DAC856x
Using line passing through codes 512 and 65,024
Differential nonlinearity
16-bit monotonic
UNIT
±4
±12
LSB
±0.2
±1
LSB
±1
±3
LSB
±0.1
±0.5
LSB
±0.3
±0.75
LSB
±0.05
±0.25
LSB
±1
±4
Bits
14
Relative accuracy
Using line passing through codes 128 and 16,256
Differential nonlinearity
14-bit monotonic
Resolution
DAC756x
MAX
16
Relative accuracy
Resolution
DAC816x
TYP
(1)
Bits
12
Relative accuracy
Using line passing through codes 32 and 4,064
Differential nonlinearity
12-bit monotonic
Offset error
Extrapolated from two-point line
Bits
(1)
, unloaded
Offset error drift
±2
Full-scale error
DAC register loaded with all 1s
±0.03
±0.2
Zero-code error
DAC register loaded with all 0s
1
4
Zero-code error drift
±2
Extrapolated from two-point line (1), unloaded
Gain error
±0.01
Gain temperature coefficient
mV
µV/°C
% FSR
mV
µV/°C
±0.15
% FSR
ppm
FSR/°C
±1
OUTPUT CHARACTERISTICS (2)
Output voltage range
0
Output voltage settling time (3)
Slew rate
7
RL = 1 MΩ
10
Measured between 20%–80% of a full-scale transition
Capacitive load stability
AVDD
DACs unloaded
0.75
RL = ∞
1
RL = 2 kΩ
3
V
µs
V/µs
nF
Code-change glitch impulse
1-LSB change around major carry
0.1
nV-s
Digital feedthrough
SCLK toggling, SYNC high
0.1
nV-s
Power-on glitch impulse
RL = 2 kΩ, CL = 470 pF, AVDD = 5.5 V
40
mV
Full-scale swing on adjacent channel,
External reference
5
Full-scale swing on adjacent channel,
Internal reference
15
Channel-to-channel dc crosstalk
µV
DC output impedance
At mid-scale input
5
Ω
Short-circuit current
DAC outputs at full-scale, DAC outputs shorted to
GND
40
mA
Power-up time, including settling time
Coming out of power-down mode
50
µs
DAC output noise density
TA = 25°C, at mid-scale input, fOUT = 1 kHz
90
nV/√Hz
DAC output noise
TA = 25°C, at mid-scale input, 0.1 Hz to 10 Hz
2.6
µVPP
AC PERFORMANCE (2)
(1)
(2)
(3)
6
16-bit: codes 512 and 65,024; 14-bit: codes 128 and 16,256; 12-bit: codes 32 and 4,064
Specification based on design or characterization. Not production tested
Transition time between 1 / 4 scale and 3 / 4 scale, including settling to within ±0.024% FSR
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Electrical Characteristics (continued)
At AVDD = 2.7 V to 5.5 V and TA = –40°C to 125°C (unless otherwise noted).
PARAMETER
LOGIC INPUTS
TEST CONDITIONS
MIN
TYP
–1
±0.1
MAX
UNIT
(2)
Input-pin leakage current
Logic input LOW voltage VIL
Logic input HIGH voltage VIH
1
µA
0
0.8
V
0.7 ×
AVDD
AVDD
V
3
pF
Pin capacitance
REFERENCE
External VREF = 2.5 V (when internal reference is
disabled), all channels active using gain = 1
External reference current
Reference input impedance
15
Internal reference disabled, gain = 1
170
Internal reference disabled, gain = 2
85
µA
kΩ
REFERENCE OUTPUT
Output voltage
TA = 25°C
2.495
2.5
2.505
Initial accuracy
TA = 25°C
–5
±0.1
5
mV
4
10
ppm/°C
Output-voltage temperature drift
Output-voltage noise
f = 0.1 Hz to 10 Hz
Output-voltage noise density (highfrequency noise)
Load regulation, sourcing (4)
Load regulation, sinking
(4)
12
250
TA = 25°C, f = 1 MHz, CL = 0 µF
30
TA = 25°C, f = 1 MHz, CL = 4.7 µF
10
TA = 25°C
20
µV/mA
TA = 25°C
185
µV/mA
nV/√Hz
±20
mA
50
µV/V
ppm
Line regulation
TA = 25°C
Long-term stability or drift (aging) (4)
TA = 25°C, time = 0 to 1900 hours
100
First cycle
200
(4)
µVPP
TA = 25°C, f = 1 kHz, CL = 0 µF
Output-current load capability (2)
Thermal hysteresis (4)
V
Additional cycles
50
ppm
See the Application Information section of this data sheet.
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
7
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Electrical Characteristics (continued)
At AVDD = 2.7 V to 5.5 V and TA = –40°C to 125°C (unless otherwise noted).
PARAMETER
POWER REQUIREMENTS
TEST CONDITIONS
Power supply current (IDD)
Power dissipation
(5)
(6)
8
MIN
TYP
MAX
AVDD = 3.6 V to 5.5 V, normal mode, internal
reference off
0.25
0.5
AVDD = 3.6 V to 5.5 V, normal mode, internal
reference on
0.9
1.6
AVDD = 3.6 V to 5.5 V, power-down modes (6)
0.55
2
AVDD = 3.6 V to 5.5 V, power-down modes
0.55
4
AVDD = 2.7 V to 3.6 V, normal mode, internal
reference off
0.2
0.4
AVDD = 2.7 V to 3.6 V, normal mode, internal
reference on
0.73
1.4
AVDD = 2.7 V to 3.6 V, power-down modes (6)
0.35
2
AVDD = 2.7 V to 3.6 V, power-down modes
0.35
3
AVDD = 3.6 V to 5.5 V, normal mode, internal
reference off
0.9
2.75
AVDD = 3.6 V to 5.5 V, normal mode, internal
reference on
3.2
8.8
AVDD = 3.6 V to 5.5 V, power-down modes (6)
2
11
AVDD = 3.6 V to 5.5 V, power-down modes
2
22
AVDD = 2.7 V to 3.6 V, normal mode, internal
reference off
0.54
1.44
AVDD = 2.7 V to 3.6 V, normal mode, internal
reference on
1.97
5
AVDD = 2.7 V to 3.6 V, power-down modes (6)
0.95
7.2
AVDD = 2.7 V to 3.6 V, power-down modes
0.95
10.8
UNIT
(5)
mA
µA
mA
µA
mW
µW
mW
µW
Input code = mid-scale, no load, VINH = AVDD, and VINL = GND
TA = –40°C to 105°C
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
7.6 Timing Requirements (1) (2)
At AVDD = 2.7 V to 5.5 V and over –40°C to 125°C (unless otherwise noted).
DAC756x, DAC816x,
DAC856x
MIN
TYP
UNIT
MAX
f(SCLK)
Serial clock frequency
t(1)
SCLK falling edge to SYNC falling edge (for successful write operation)
10
ns
t(2)
SCLK cycle time
20
ns
t(3)
SYNC rising edge to 23rd SCLK falling edge (for successful SYNC interrupt)
13
ns
t(4)
Minimum SYNC HIGH time
80
ns
t(5)
SYNC to SCLK falling edge setup time
13
ns
t(6)
SCLK LOW time
8
ns
t(7)
SCLK HIGH time
8
ns
t(8)
SCLK falling edge to SYNC rising edge
10
ns
t(9)
Data setup time
6
ns
t(10)
Data hold time
5
ns
t(11)
SCLK falling edge to LDAC falling edge for asynchronous LDAC update mode
5
ns
t(12)
LDAC pulse duration, LOW time
10
ns
t(13)
CLR pulse duration, LOW time
80
t(14)
CLR falling edge to start of VOUT transition
(1)
(2)
50
MHz
ns
100
ns
All input signals are specified with tr = tf = 3 ns (10% to 90% of AVDD) and timed from a voltage level of (VIL + VIH) / 2.
See the Serial Write Operation timing diagram (Figure 1).
t(1)
t(2)
SCLK
t(6)
t(5)
t(3)
t(7)
t(8)
t(4)
SYNC
t(10)
t(9)
DIN
DB23
DB0
t(12)
t(11)
LDAC(1)
LDAC(2)
t(13)
CLR
t(14)
VOUTx
(1)
Asynchronous LDAC update mode. For more information, see the LDAC Functionality section.
(2)
Synchronous LDAC update mode; LDAC remains low. For more information, see the LDAC Functionality section.
Figure 1. Serial Write Operation
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
9
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
7.7 Typical Characteristics
Table 1. Typical Characteristics: Internal Reference Performance
POWER-SUPPLY
VOLTAGE
MEASUREMENT
FIGURE NUMBER
Internal Reference Voltage vs Temperature
Figure 2
Internal Reference Voltage Temperature Drift Histogram
Figure 3
Internal Reference Voltage vs Load Current
5.5 V
Figure 4
Internal Reference Voltage vs Time
Figure 5
Internal Reference Noise Density vs Frequency
Figure 6
Internal Reference Voltage vs Supply Voltage
2.7 V–5.5 V
Figure 7
Table 2. Typical Characteristics: DAC Static Performance
POWER-SUPPLY
VOLTAGE
MEASUREMENT
FIGURE NUMBER
FULL-SCALE, GAIN, OFFSET AND ZERO-CODE ERRORS
Full-Scale Error vs Temperature
Figure 16
Gain Error vs Temperature
5.5 V
Offset Error vs Temperature
Figure 17
Figure 18
Zero-Code Error vs Temperature
Figure 19
Full-Scale Error vs Temperature
Figure 63
Gain Error vs Temperature
2.7 V
Offset Error vs Temperature
Zero-Code Error vs Temperature
Figure 64
Figure 65
Figure 66
LOAD REGULATION
DAC Output Voltage vs Load Current
5.5 V
Figure 30
2.7 V
Figure 74
DIFFERENTIAL NONLINEARITY ERROR
Differential Linearity Error vs Digital Input Code
T = –40°C
Figure 9
T = 25°C
Figure 11
T = 125°C
5.5 V
Differential Linearity Error vs Temperature
Figure 15
T = –40°C
Differential Linearity Error vs Digital Input Code
Figure 13
T = 25°C
T = 125°C
Figure 56
2.7 V
Differential Linearity Error vs Temperature
Figure 58
Figure 60
Figure 62
INTEGRAL NONLINEARITY ERROR (RELATIVE ACCURACY)
T = –40°C
Linearity Error vs Digital Input Code
T = 25°C
T = 125°C
Figure 8
5.5 V
Linearity Error vs Temperature
T = 25°C
T = 125°C
Figure 55
2.7 V
Linearity Error vs Temperature
10
Submit Documentation Feedback
Figure 12
Figure 14
T = –40°C
Linearity Error vs Digital Input Code
Figure 10
Figure 57
Figure 59
Figure 61
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Table 2. Typical Characteristics: DAC Static Performance (continued)
MEASUREMENT
POWER-SUPPLY
VOLTAGE
FIGURE NUMBER
POWER-DOWN CURRENT
Power-Down Current vs Temperature
Power-Down Current vs Power-Supply Voltage
Power-Down Current vs Temperature
5.5 V
Figure 28
2.7 V – 5.5 V
Figure 29
2.7 V
Figure 73
POWER-SUPPLY CURRENT
Power-Supply Current vs Temperature
Power-Supply Current vs Digital Input Code
Power-Supply Current Histogram
Power-Supply Current vs Power-Supply Voltage
Power-Supply Current vs Temperature
Power-Supply Current vs Digital Input Code
Power-Supply Current Histogram
Power-Supply Current vs Temperature
Power-Supply Current vs Digital Input Code
Power-Supply Current Histogram
External VREF
Figure 20
Internal VREF
Figure 21
External VREF
Internal VREF
5.5 V
Figure 22
Figure 23
External VREF
Figure 24
Internal VREF
Figure 25
External VREF
Internal VREF
2.7 V – 5.5 V
Figure 26
Figure 27
External VREF
Figure 49
Internal VREF
Figure 50
External VREF
Internal VREF
3.6 V
Figure 51
Figure 52
External VREF
Figure 53
Internal VREF
Figure 54
External VREF
Figure 67
Internal VREF
Figure 68
External VREF
Internal VREF
2.7 V
Figure 69
Figure 70
External VREF
Figure 71
Internal VREF
Figure 72
Table 3. Typical Characteristics: DAC Dynamic Performance
MEASUREMENT
POWER-SUPPLY
VOLTAGE
FIGURE NUMBER
CHANNEL-TO-CHANNEL CROSSTALK
Channel-to-Channel Crosstalk
5-V Rising Edge
5-V Falling Edge
5.5 V
Figure 43
Figure 44
CLOCK FEEDTHROUGH
Clock Feedthrough
500 kHz, Midscale
5.5 V
Figure 48
2.7 V
Figure 87
GLITCH IMPULSE
Glitch Impulse, 1-LSB Step
Glitch Impulse, 4-LSB Step
Glitch Impulse, 16-LSB Step
Rising Edge, Code 7FFFh to 8000h
Figure 37
Falling Edge, Code 8000h to 7FFFh
Figure 38
Rising Edge, Code 7FFCh to 8000h
Falling Edge, Code 8000h to 7FFCh
5.5 V
Figure 39
Figure 40
Rising Edge, Code 7FF0h to 8000h
Figure 41
Falling Edge, Code 8000h to 7FF0h
Figure 42
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
11
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Table 3. Typical Characteristics: DAC Dynamic Performance (continued)
MEASUREMENT
Glitch Impulse, 1-LSB Step
Glitch Impulse, 4-LSB Step
Glitch Impulse, 16-LSB Step
POWER-SUPPLY
VOLTAGE
FIGURE NUMBER
Rising Edge, Code 7FFFh to 8000h
Figure 79
Falling Edge, Code 8000h to 7FFFh
Figure 80
Rising Edge, Code 7FFCh to 8000h
Falling Edge, Code 8000h to 7FFCh
2.7 V
Figure 81
Figure 82
Rising Edge, Code 7FF0h to 8000h
Figure 83
Falling Edge, Code 8000h to 7FF0h
Figure 84
NOISE
DAC Output Noise Density vs
Frequency
External VREF
DAC Output Noise 0.1 Hz to 10 Hz
External VREF
Internal VREF
Figure 45
5.5 V
Figure 46
Figure 47
POWER-ON GLITCH
Reset to Zero Scale
Power-On Glitch
Reset to Midscale
Reset to Zero Scale
Reset to Midscale
5.5 V
2.7 V
Figure 35
Figure 36
Figure 85
Figure 86
SETTLING TIME
Full-Scale Settling Time
Half-Scale Settling Time
Full-Scale Settling Time
Half-Scale Settling Time
12
Rising Edge, Code 0h to FFFFh
Falling Edge, Code FFFFh to 0h
Rising Edge, Code 4000h to C000h
Figure 31
5.5 V
Figure 32
Figure 33
Falling Edge, Code C000h to 4000h
Figure 34
Rising Edge, Code 0h to FFFFh
Figure 75
Falling Edge, Code FFFFh to 0h
Rising Edge, Code 4000h to C000h
2.7 V
Falling Edge, Code C000h to 4000h
Submit Documentation Feedback
Figure 76
Figure 77
Figure 78
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
7.7.1 Typical Characteristics: Internal Reference
At TA = 25°C, AVDD = 5.5 V, gain = 2, and VREFOUT unloaded, unless otherwise noted.
30
2.505
2.504
25
2.503
Population (%)
2.501
2.500
2.499
2.498
2.497
15
10
5
60 units shown
(30 MSOP, 30 SON-10)
2.496
0
2.495
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
Temperature Drift (ppm/ °C)
Figure 2. Internal Reference Voltage vs Temperature
Figure 3. Internal Reference Voltage, Temperature Drift
Histogram
400
Internal Reference Voltage Shift (ppm)
2.510
2.505
VREFOUT (V)
20
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
VREFOUT (V)
2.502
2.500
2.495
2.490
−20
−15
−10
−5
0
5
Load Current (mA)
10
15
300
200
100
0
−100
−200
−300
−400
20
Figure 4. Internal Reference Voltage vs Load Current
0
250
500
750
1000
Elapsed Time (Hours)
1250
1500
Figure 5. Internal Reference Voltage vs Time
400
2.505
No Load
4.7 µF Load
350
−40°C
+25°C
+125°C
2.504
2.503
300
2.502
250
VREFOUT (V)
Voltage Noise (nV/rt−Hz)
16 units shown (8 MSOP, 8 SON-10)
Average shown in dashed line
200
150
2.501
2.500
2.499
2.498
100
2.497
50
0
2.496
10
100
1k
10k
Frequency (Hz)
100k
1M
Figure 6. Internal Reference Noise Density vs Frequency
Copyright © 2010–2015, Texas Instruments Incorporated
2.495
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
AVDD (V)
Figure 7. Internal Reference Voltage vs Supply Voltage
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
13
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
7.7.2 Typical Characteristics: DAC at AVDD = 5.5 V
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
−40°C
0
Typical channel shown
−40°C
−0.8
−1.0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 8. Linearity Error vs Digital Input Code (–40°C)
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 9. Differential Linearity Error vs Digital Input Code
(–40°C)
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
25°C
0
Typical channel shown
25°C
−0.8
−1.0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 10. Linearity Error vs Digital Input Code (25°C)
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 11. Differential Linearity Error vs Digital Input Code
(25°C)
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
125°C
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 12. Linearity Error vs Digital Input Code (125°C)
14
Submit Documentation Feedback
Typical channel shown
125°C
−0.8
−1.0
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 13. Differential Linearity Error vs Digital Input Code
(125°C)
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
12
1.0
INL Max
INL Min
9
DNL Max
DNL Min
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
Typical channel shown
−12
−40 −25 −10 5
20 35 50 65
Temperature (°C)
−0.8
80
95
Typical channel shown
−1.0
−40 −25 −10 5
20 35 50 65
Temperature (°C)
110 125
Figure 14. Linearity Error vs Temperature
95
110 125
Figure 15. Differential Linearity Error vs Temperature
0.20
0.15
Ch A
Ch B
0.15
Ch A
Ch B
0.10
0.10
Gain Error (%FSR)
Full−Scale Error (%FSR)
80
0.05
0.00
−0.05
0.05
0.00
−0.05
−0.10
−0.10
−0.15
−0.20
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
−0.15
−40 −25 −10
110 125
Figure 16. Full-Scale Error vs Temperature
20 35 50 65
Temperature (°C)
80
95
110 125
Figure 17. Gain Error vs Temperature
4
4.0
Ch A
Ch B
3
1
0
−1
−2
−3
Ch A
Ch B
3.5
Zero−Code Error (mV)
2
Offset Error (mV)
5
3.0
2.5
2.0
1.5
1.0
0.5
−4
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
Figure 18. Offset Error vs Temperature
Copyright © 2010–2015, Texas Instruments Incorporated
110 125
0.0
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
Figure 19. Zero-Code Error vs Temperature
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
15
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
0.50
1.3
0.45
1.2
Power−Supply Current (mA)
0.40
0.35
0.30
0.25
0.20
0.15
0.10
1.1
1.0
0.9
0.8
0.7
0.6
0.05
0.00
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
0.5
−40 −25 −10
110 125
0.50
1.3
0.45
1.2
0.40
0.35
0.30
0.25
0.20
0.15
0.10
80
95
110 125
1.1
1.0
0.9
0.8
0.7
Internal reference enabled, Gain = 2
0
0.5
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 23. Power-Supply Current vs Digital Input Code
30
30
25
25
20
20
Population (%)
Figure 22. Power-Supply Current vs Digital Input Code
15
10
10
0.45
0.43
0.41
0.39
0.37
0.35
0.33
0.31
0.29
0.27
0.25
0.23
0
0.21
0
0.19
5
0.17
Internal reference enabled
Gain = 2
15
5
0.15
Population (%)
20 35 50 65
Temperature (°C)
0.6
0.05
16
5
Figure 21. Power-Supply Current vs Temperature
Power−Supply Current (mA)
Power−Supply Current (mA)
Figure 20. Power-Supply Current vs Temperature
0.00
Internal reference enabled
DACs at midscale code, Gain = 2
DACs at midscale code
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
Power−Supply Current (mA)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
Power Supply Current (mA)
Power Supply Current (mA)
Figure 24. Power-Supply Current Histogram
Figure 25. Power-Supply Current Histogram
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
0.50
1.3
VREFIN = 2.5 V
DACs at midscale code, Gain = 1
1.2
Power−Supply Current (mA)
Power−Supply Current (mA)
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
Internal reference enabled
DACs at midscale code, Gain = 1
1.1
1.0
0.9
0.8
0.7
0.6
0.05
0.00
2.7
3.1
3.5
3.9
4.3
4.7
5.1
0.5
2.7
5.5
3.1
3.5
AVDD (V)
4.7
5.1
5.5
Figure 27. Power-Supply Current vs Power-Supply Voltage
4.0
0.60
Power−Down Current (µA)
3.5
Power−Down Current (µA)
4.3
AVDD (V)
Figure 26. Power-Supply Current vs Power-Supply Voltage
3.0
2.5
2.0
1.5
1.0
0.5
0.0
−40 −25 −10
3.9
5
20 35 50 65
Temperature (°C)
80
95
IDD (µA)
IREFIN (µA)
0.50
0.40
0.30
0.20
0.10
0.00
2.7
110 125
3.1
3.5
G028
Figure 28. Power-Down Current vs Temperature
3.9
4.3
AVDD (V)
4.7
5.1
5.5
G029
Figure 29. Power-Down Current vs Power-Supply Voltage
7.0
Typical channel shown
Full scale
Mid scale
Zero scale
6.0
Output Voltage (V)
5.0
4.0
3.0
2.0
1.0
0.0
−1.0
−20
−15
−10
−5
0
5
10
15
20
ILOAD (mA)
Figure 30. DAC Output Voltage vs Load Current
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
17
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
Large Signal VOUT (2 V/div)
Large Signal VOUT (2 V/div)
Small Signal Settling
(1.22 mV/div = 0.024% FSR)
Small Signal Settling (1.22 mV/div = 0.024% FSR)
From Code: FFFFh
To Code: 0h
From Code: 0h
To Code: FFFFh
Time (5 μs/div)
Time (5 μs/div)
Figure 31. Full-Scale Settling Time, Rising Edge
Figure 32. Full-Scale Settling Time, Falling Edge
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
Large Signal VOUT (2 V/div)
Large Signal VOUT (2 V/div)
Small Signal Settling (1.22 mV/div = 0.024% FSR)
Small Signal Settling (1.22 mV/div = 0.024% FSR)
From Code: 4000h
To Code: C000h
Time (5 μs/div)
From Code: C000h
To Code: 4000h
Time (5 μs/div)
Figure 33. Half-Scale Settling Time, Rising Edge
AVDD (2 V/div)
Figure 34. Half-Scale Settling Time, Falling Edge
AVDD (2 V/div)
VOUTA (1 V/div)
VOUTB (1 V/div)
VOUTA (50 mV/div)
VOUTB (50 mV/div)
VREFIN shorted to AVDD
VREFIN shorted to AVDD
Time (1 ms/div)
Figure 35. Power-On Glitch, Reset to Zero Scale
18
Submit Documentation Feedback
Time (1 ms/div)
Figure 36. Power-On Glitch, Reset to Midscale
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
LDAC Feedthrough
Glitch Impulse » 0.1 nV-s
VOUT (100 μV/div)
VOUT (100 μV/div)
LDAC Feedthrough
Glitch Impulse » 0.12 nV-s
From Code: 7FFFh
To Code: 8000h
Time (5 μs/div)
From Code: 8000h
To Code: 7FFFh
Time (5 μs/div)
Figure 37. Glitch Impulse, Rising Edge, 1-LSB Step
Figure 38. Glitch Impulse, Falling Edge, 1-LSB Step
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
Glitch Impulse » 0.1 nV-s
LDAC Feedthrough
VOUT (100 μV/div)
VOUT (100 μV/div)
LDAC Feedthrough
Glitch Impulse » 0.14 nV-s
From Code: 8000h
To Code: 7FFCh
From Code: 7FFCh
To Code: 8000h
Time (5 μs/div)
Time (5 μs/div)
Figure 39. Glitch Impulse, Rising Edge, 4-LSB Step
Figure 40. Glitch Impulse, Falling Edge, 4-LSB Step
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
Glitch Impulse » 0.1 nV-s
VOUT (500 μV/div)
LDAC Feedthrough
LDAC Feedthrough
Glitch Impulse » 0.1 nV-s
VOUT (500 μV/div)
From Code: 7FF0h
To Code: 8000h
Time (5 μs/div)
Figure 41. Glitch Impulse, Rising Edge, 16-LSB Step
Copyright © 2010–2015, Texas Instruments Incorporated
From Code: 8000h
To Code: 7FF0h
Time (5 μs/div)
Figure 42. Glitch Impulse, Falling Edge, 16-LSB Step
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
19
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Characteristics: DAC at AVDD = 5.5 V (continued)
At TA = 25°C, 5-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
VOUTB (1 V/div)
6.4 μs
Glitch Area (Between Cursors) = 2 nV-s
VOUTA (500 μV/div)
VOUTA (500 μV/div)
VOUTA at Midscale Code
Internal Reference Enabled
Gain = 2
Glitch Area (Between Cursors) = 1.6 nV-s
7.3 μs
VOUTB (1 V/div)
VOUTA at Midscale Code
Internal Reference Enabled
Gain = 2
Time (5 μs/div)
Time (5 μs/div)
Figure 43. Channel-to-Channel Crosstalk, 5-V Rising Edge
Figure 44. Channel-to-Channel Crosstalk, 5-V Falling Edge
1400
1400
Voltage Noise (nV/rt−Hz)
1200
Full Scale
Mid Scale
Zero Scale
1000
800
600
400
200
0
Internal reference enabled
Gain = 2
1200
Voltage Noise (nV/rt−Hz)
Internal reference disabled
VREFIN = 5 V, Gain = 1
Full Scale
Mid Scale
Zero Scale
1000
800
600
400
200
10
100
1k
Frequency (Hz)
10k
100k
Figure 45. DAC Output Noise Density vs Frequency
0
10
100
1k
Frequency (Hz)
10k
100k
Figure 46. DAC Output Noise Density vs Frequency
VNOISE (1 μV/div)
SCLK (5 V/div)
VOUT (500 μV/div)
» 2.5 μVPP
Clock Feedthrough Impulse » 0.06 nV-s
DAC = Midscale
Time (500 ns/div)
Figure 47. DAC Output Noise, 0.1 Hz to 10 Hz
20
Submit Documentation Feedback
Figure 48. Clock Feedthrough, 500 kHz, Midscale
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
7.7.3 Typical Characteristics: DAC at AVDD = 3.6 V
0.50
1.3
0.45
1.2
Power−Supply Current (mA)
0.40
0.35
0.30
0.25
0.20
0.15
0.10
1.1
1.0
0.9
0.8
0.7
0.6
0.05
0.00
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
0.5
−40 −25 −10
110 125
0.50
1.3
0.45
1.2
0.40
0.35
0.30
0.25
0.20
0.15
0.10
20 35 50 65
Temperature (°C)
80
95
110 125
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.05
Internal reference enabled, Gain = 1
0
0.4
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 52. Power-Supply Current vs Digital Input Code
30
30
25
25
20
20
Population (%)
Figure 51. Power-Supply Current vs Digital Input Code
15
10
10
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.18
0
0.16
0
0.14
5
0.12
Internal reference enabled
Gain = 1
15
5
0.10
Population (%)
5
Figure 50. Power-Supply Current vs Temperature
Power−Supply Current (mA)
Power−Supply Current (mA)
Figure 49. Power-Supply Current vs Temperature
0.00
Internal reference enabled
DACs at midscale code, Gain = 1
DACs at midscale code
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
Power−Supply Current (mA)
At TA = 25°C, 3.3-V external reference used, gain = 1 and DAC output not loaded, unless otherwise noted.
Power Supply Current (mA)
Power Supply Current (mA)
Figure 53. Power-Supply Current Histogram
Figure 54. Power-Supply Current Histogram
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
21
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
7.7.4 Typical Characteristics: DAC at AVDD = 2.7 V
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
−40°C
0
Typical channel shown
−40°C
−0.8
−1.0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 55. Linearity Error vs Digital Input Code (–40°C)
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 56. Differential Linearity Error vs Digital Input Code
(–40°C)
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
25°C
0
Typical channel shown
25°C
−0.8
−1.0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 57. Linearity Error vs Digital Input Code (25°C)
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 58. Differential Linearity Error vs Digital Input Code
(25°C)
12
1.0
9
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
−12
Typical channel shown
125°C
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 59. Linearity Error vs Digital Input Code (125°C)
22
Submit Documentation Feedback
Typical channel shown
125°C
−0.8
−1.0
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 60. Differential Linearity Error vs Digital Input Code
(125°C)
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 2.7 V (continued)
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
12
1.0
INL Max
INL Min
9
DNL Max
DNL Min
0.8
0.6
DNL Error (LSB)
INL Error (LSB)
6
3
0
−3
0.4
0.2
0.0
−0.2
−0.4
−6
−0.6
−9
Typical channel shown
−12
−40 −25 −10 5
20 35 50 65
Temperature (°C)
−0.8
80
95
Typical channel shown
−1.0
−40 −25 −10 5
20 35 50 65
Temperature (°C)
110 125
Figure 61. Linearity Error vs Temperature
95
110 125
Figure 62. Differential Linearity Error vs Temperature
0.20
0.15
Ch A
Ch B
0.15
Ch A
Ch B
0.10
0.10
Gain Error (%FSR)
Full−Scale Error (%FSR)
80
0.05
0.00
−0.05
0.05
0.00
−0.05
−0.10
−0.10
−0.15
−0.20
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
−0.15
−40 −25 −10
110 125
Figure 63. Full-Scale Error vs Temperature
20 35 50 65
Temperature (°C)
80
95
110 125
Figure 64. Gain Error vs Temperature
4
4.0
Ch A
Ch B
3
1
0
−1
−2
−3
Ch A
Ch B
3.5
Zero−Code Error (mV)
2
Offset Error (mV)
5
3.0
2.5
2.0
1.5
1.0
0.5
−4
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
Figure 65. Offset Error vs Temperature
Copyright © 2010–2015, Texas Instruments Incorporated
110 125
0.0
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
Figure 66. Zero-Code Error vs Temperature
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
23
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Characteristics: DAC at AVDD = 2.7 V (continued)
0.40
1.3
0.35
1.2
Power−Supply Current (mA)
Power−Supply Current (mA)
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
0.30
0.25
0.20
0.15
0.10
0.05
1.1
1.0
0.9
0.8
0.7
0.6
Internal reference enabled
DACs at midscale code, Gain = 1
DACs at midscale code
0.00
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
0.5
−40 −25 −10
110 125
0.40
1.3
0.35
1.2
0.30
0.25
0.20
0.15
0.10
20 35 50 65
Temperature (°C)
80
95
110 125
Figure 68. Power-Supply Current vs Temperature
Power−Supply Current (mA)
Power−Supply Current (mA)
Figure 67. Power-Supply Current vs Temperature
5
0.05
1.1
1.0
0.9
0.8
0.7
0.6
0.5
Internal reference enabled, Gain = 1
24
0
0.4
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
0
8192 16384 24576 32768 40960 49152 57344 65536
Digital Input Code
Figure 70. Power-Supply Current vs Digital Input Code
30
30
25
25
20
20
15
10
15
10
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0
0.18
0
0.16
5
0.14
5
0.12
Internal reference enabled
Gain = 1
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
Population (%)
Figure 69. Power-Supply Current vs Digital Input Code
0.10
Population (%)
0.00
Power Supply Current (mA)
Power Supply Current (mA)
Figure 71. Power-Supply Current Histogram
Figure 72. Power-Supply Current Histogram
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 2.7 V (continued)
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
3.0
4
Full scale
Mid scale
Zero scale
3
2.0
Output Voltage (V)
Power−Down Current (µA)
Typical channel shown
2.5
1.5
1.0
0.5
2
1
0
0.0
−40 −25 −10
5
20 35 50 65
Temperature (°C)
80
95
110 125
G073
−1
−20
−15
−10
−5
0
5
10
15
20
ILOAD (mA)
Figure 73. Power-Down Current vs Temperature
LDAC Trigger (5 V/div)
Figure 74. DAC Output Voltage vs Load Current
LDAC Trigger (5 V/div)
Large Signal VOUT (1 V/div)
Large Signal VOUT (1 V/div)
Small Signal Settling (0.61 mV/div = 0.024% FSR)
Small Signal Settling (0.61 mV/div = 0.024% FSR)
From Code: FFFFh
To Code: 0h
From Code: 0h
To Code: FFFFh
Time (5 μs/div)
Time (5 μs/div)
Figure 75. Full-Scale Settling Time, Rising Edge
LDAC Trigger (5 V/div)
Figure 76. Full-Scale Settling Time, Falling Edge
LDAC Trigger (5 V/div)
Large Signal VOUT (1 V/div)
Large Signal VOUT (1 V/div)
Small Signal Settling (0.61 mV/div = 0.024% FSR)
Small Signal Settling (0.61 mV/div = 0.024% FSR)
From Code: 4000h
To Code: C000h
Time (5 μs/div)
Figure 77. Half-Scale Settling Time, Rising Edge
Copyright © 2010–2015, Texas Instruments Incorporated
From Code: C000h
To Code: 4000h
Time (5 μs/div)
Figure 78. Half-Scale Settling Time, Falling Edge
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
25
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Characteristics: DAC at AVDD = 2.7 V (continued)
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
LDAC Feedthrough
Glitch Impulse » 0.1 nV-s
VOUT (100 μV/div)
VOUT (100 μV/div)
LDAC Feedthrough
Glitch Impulse » 0.1 nV-s
From Code: 7FFFh
To Code: 8000h
From Code: 8000h
To Code: 7FFFh
Time (5 μs/div)
Time (5 μs/div)
Figure 79. Glitch Impulse, Rising Edge, 1-LSB Step
Figure 80. Glitch Impulse, Falling Edge, 1-LSB Step
LDAC Trigger (5 V/div)
LDAC Trigger (5 V/div)
Glitch Impulse » 0.1 nV-s
LDAC Feedthrough
VOUT (100 μV/div)
VOUT (100 μV/div)
LDAC Feedthrough
Glitch Impulse » 0.1 nV-s
From Code: 7FFCh
To Code: 8000h
From Code: 8000h
To Code: 7FFCh
Time (5 μs/div)
Time (5 μs/div)
Figure 81. Glitch Impulse, Rising Edge, 4-LSB Step
Figure 82. Glitch Impulse, Falling Edge, 4-LSB Step
LDAC Trigger (5 V/div)
Glitch Impulse » 0.1 nV-s
VOUT (200 μV/div)
LDAC Trigger (5 V/div)
LDAC Feedthrough
LDAC Feedthrough
VOUT (200 μV/div)
Glitch Impulse » 0.1 nV-s
From Code: 7FF0h
To Code: 8000h
Time (5 μs/div)
Figure 83. Glitch Impulse, Rising Edge, 16-LSB Step
26
Submit Documentation Feedback
From Code: 8000h
To Code: 7FF0h
Time (5 μs/div)
Figure 84. Glitch Impulse, Falling Edge, 16-LSB Step
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Characteristics: DAC at AVDD = 2.7 V (continued)
At TA = 25°C, 2.5-V external reference used, gain = 1, and DAC output not loaded, unless otherwise noted.
AVDD (2 V/div)
AVDD (2 V/div)
VOUTA (500 mV/div)
VOUTB (500 mV/div)
VOUTA (50 mV/div)
VOUTB (50 mV/div)
VREFIN shorted to AVDD
VREFIN shorted to AVDD
Time (1 ms/div)
Time (1 ms/div)
Figure 85. Power-On Glitch, Reset to Zero Scale
Figure 86. Power-On Glitch, Reset to Midscale
SCLK (2 V/div)
Clock Feedthrough Impulse » 0.02 nV-s
VOUT (500 μV/div)
Time (500 ns/div)
Figure 87. Clock Feedthrough, 500 kHz, Midscale
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
27
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
8 Detailed Description
8.1 Overview
The DAC756x, DAC816x, and DAC856x devices are low-power, voltage-output, dual-channel, 16-, 14-, and
12-bit digital-to-analog converters (DACs), respectively. These devices include a 2.5-V, 4-ppm/°C internal
reference, giving a full-scale output voltage range of 2.5 V or 5 V. The internal reference has an initial accuracy
of ±5 mV and can source or sink up to 20 mA at the VREFIN/VREFOUT pin.
8.2 Functional Block Diagram
GND
DIN
SCLK
SYNC
LDAC
AVDD
CLR
Buffer Control
VREFIN/VREFOUT
Register Control
2.5-V
Reference
Input Control Logic
Control Logic
DAC756x (12-Bit)
DAC816x (14-Bit)
DAC856x (16-Bit)
PowerDown
Control
Logic
Data Buffer B
DAC Register B
DAC
VOUTB
Data Buffer A
DAC Register A
DAC
VOUTA
8.3 Feature Description
8.3.1 Digital-to-Analog Converter (DAC)
The DAC756x, DAC816x, and DAC856x architecture consists of two string DACs, each followed by an output
buffer amplifier. The devices include an internal 2.5-V reference with 4-ppm/°C temperature drift performance.
Figure 88 shows a principal block diagram of the DAC architecture.
Gain
Register
DIN
n
DAC
Register
VREFIN/
VREFOUT
150 kW
REF(+)
Resistor String
REF(-)
150 kW
VOUT
GND
Figure 88. DAC Architecture
The input coding to the DAC756x, DAC816x, and DAC856x devices is straight binary, so the ideal output voltage
is given by Equation 1:
æD ö
VO UT = ç IN
´ VREF ´ Gain
n ÷
è 2 ø
(1)
where:
n = resolution in bits; either 12 (DAC756x), 14 (DAC816x) or 16 (DAC856x)
DIN = decimal equivalent of the binary code that is loaded to the DAC register. DIN ranges from 0 to 2n – 1.
VREF = DAC reference voltage; either VREFOUT from the internal 2.5-V reference or VREFIN from an
aaa external reference.
Gain = 1 by default when internal reference is disabled (using external reference), and gain = 2 by default
aaa when using internal reference. Gain can also be manually set to either 1 or 2 using the gain register.
aaa See the Gain Function section for more information.
28
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Feature Description (continued)
8.3.1.1 Resistor String
The resistor string section is shown in Figure 89. It is simply a string of resistors, each of value R. The code
loaded into the DAC register determines at which node on the string the voltage is tapped off to be fed into the
output amplifier by closing one of the switches connecting the string to the amplifier. The resistor string
architecture results in monotonicity. The RDIVIDER switch is controlled by the gain registers (see the Gain Function
section). Because the output amplifier has a gain of 2, RDIVIDER is not shorted when the DAC-n gain is set to 1
(default if internal reference is disabled), and is shorted when the DAC-n gain is set to 2 (default if internal
reference is enabled).
VREFIN/VREFOUT
RDIVIDER
VREF
2
R
R
To Output Amplifier
R
R
Figure 89. Resistor String
8.3.1.2 Output Amplifier
The output buffer amplifier is capable of generating rail-to-rail voltages on its output, giving a maximum output
range of 0 V to AVDD. It is capable of driving a load of 2 kΩ in parallel with 3 nF to GND. The typical slew rate is
0.75 V/µs, with a typical full-scale settling time of 14 µs as shown in Figure 31, Figure 32, Figure 75 and
Figure 76.
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
29
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
8.3.2 Internal Reference
The DAC756x, DAC816x, and DAC856x devices include a 2.5-V internal reference that is disabled by default.
The internal reference is externally available at the VREFIN/VREFOUT pin. The internal reference output voltage is
2.5 V and can sink and source up to 20 mA.
A minimum 150-nF capacitor is recommended between the reference output and GND for noise filtering.
The internal reference of the DAC756x, DAC816x, and DAC856x devices is a bipolar transistor-based precision
band-gap voltage reference. Figure 90 shows the basic band-gap topology. Transistors Q1 and Q2 are biased
such that the current density of Q1 is greater than that of Q2. The difference of the two base-emitter voltages
(VBE1 – VBE2) has a positive temperature coefficient and is forced across resistor R1. This voltage is amplified and
added to the base-emitter voltage of Q2, which has a negative temperature coefficient. The resulting output
voltage is virtually independent of temperature. The short-circuit current is limited by design to approximately
100 mA.
VREFIN/VREFOUT
Reference
Enable
Q1
Q2
R1
R2
Figure 90. Band-Gap Reference Simplified Schematic
8.3.3 Power-On Reset
8.3.3.1 Power-On Reset to Zero-Scale
The DAC7562, DAC8162, and DAC8562 devices contain a power-on-reset circuit that controls the output voltage
during power up. All device registers are reset as shown in Table 4. At power up, all DAC registers are filled with
zeros and the output voltages of all DAC channels are set to zero volts. Each DAC channel remains that way
until a valid load command is written to it. The power-on reset is useful in applications where it is important to
know the state of the output of each DAC while the device is in the process of powering up. No device pin should
be brought high before applying power to the device. The internal reference is disabled by default and remains
that way until a valid reference-change command is executed.
8.3.3.2 Power-On Reset to Mid-Scale
The DAC7563, DAC8163, and DAC8563 devices contain a power-on reset circuit that controls the output voltage
during power up. At power up, all DAC registers are reset to mid-scale code and the output voltages of all DAC
channels are set to VREFIN / 2 volts. Each DAC channel remains that way until a valid load command is written to
it. The power-on reset is useful in applications where it is important to know the state of the output of each DAC
while the device is in the process of powering up. No device pin should be brought high before applying power to
the device. The internal reference is powered off or down by default and remains that way until a valid referencechange command is executed. If using an external reference, it is acceptable to power on the VREFIN pin either at
the same time as or after applying AVDD.
30
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Table 4. DACxx62 and DACxx63 Power-On Reset Values
REGISTER
DEFAULT SETTING
DAC and input registers
DACxx62
Zero-scale
DACxx63
Mid-scale
LDAC registers
LDAC pin enabled for both channels
Power-down registers
DACs powered up
Internal reference register
Internal reference disabled
Gain registers
Gain = 1 for both channels
8.3.3.3 Power-On Reset (POR) Levels
When the device powers up, a POR circuit sets the device in default mode as shown in Table 4. The POR circuit
requires specific AVDD levels, as indicated in Figure 91, to ensure discharging of internal capacitors and to reset
the device on power up. In order to ensure a power-on reset, AVDD must be below 0.7 V for at least 1 ms. When
AVDD drops below 2.2 V but remains above 0.7 V (shown as the undefined region), the device may or may not
reset under all specified temperature and power-supply conditions. In this case, TI recommends a power-on
reset. When AVDD remains above 2.2 V, a power-on reset does not occur.
AVDD (V)
5.50
No Power-On Reset
Specified Supply
Voltage Range
2.70
2.20
Undefined
0.70
Power-On Reset
0.00
Figure 91. Relevant Voltage Levels for POR Circuit
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
31
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
8.4 Device Functional Modes
8.4.1 Power-Down Modes
The DAC756x, DAC816x, and DAC856x devices have two separate sets of power-down commands. One set is
for the DAC channels and the other set is for the internal reference. The internal reference is forced to a
powered-down state while both DAC channels are powered down, and is only enabled if any DAC channel is
also in the normal mode of operation. For more information on the internal reference control, see the Internal
Reference Enable Register section.
8.4.1.1 DAC Power-Down Commands
The DAC756x, DAC816x, and DAC856x DACs use four modes of operation. These modes are accessed by
setting the serial interface command bits to 100. Once the command bits are set correctly, the four different
power-down modes are software programmable by setting bits DB5 and DB4 in the shift register. Table 5 and
Table 6 show the different power-down options. For more information on how to set the DAC operating mode see
Table 17.
Table 5. DAC-n Operating Modes
DB5
DB4
0
0
Selected DACs power up (normal mode, default)
DAC Modes of Operation
0
1
Selected DACs power down, output 1 kΩ to GND
1
0
Selected DACs power down, output 100 kΩ to GND
1
1
Selected DACs power down, output Hi-Z to GND
Table 6. DAC-n Selection for Operating Modes
DAC-B (DB1), DAC-A (DB0)
Operating Mode
0
DAC-n does not change operating mode
1
DAC-n operating mode set to value on PD1 and PD0
It is possible to write to the DAC register or buffer of the DAC channel that is powered down. When the DAC
channel is then powered up, it powers up to this new value.
The advantage of the available power-down modes is that the output impedance of the device is known while it is
in power-down mode. As described in Table 5, there are three different power-down options. VOUT can be
connected internally to GND through a 1-kΩ resistor, a 100-kΩ resistor, or open-circuited (Hi-Z). The DAC
power-down circuitry is shown in Figure 92.
Resistor
String
DAC
Amplifier
Power-Down
Circuitry
VOUTX
Resistor
Network
Figure 92. Output Stage
32
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
8.4.2 Gain Function
The gain register controls the GAIN setting in the DAC transfer function:
æD ö
VO UT = ç IN
´ VREF ´ Gain
n ÷
è 2 ø
(2)
The DAC756x, DAC816x, and DAC856x devices have a gain register for each channel. The gain for each
channel, in Equation 2, is either 1 or 2. This gain is automatically set to 2 when using the internal reference, and
is automatically set to 1 when the internal reference is disabled (default). However, each channel can have either
gain by setting the registers appropriately. The gain registers are accessible by setting the serial interface
command bits to 000, address bits to 010, and using DB1 for DAC-B and DB0 for DAC-A. See Table 7 and
Table 17 for the full command structure. The gain registers are automatically reset to provide either gain of 1 or 2
when the internal reference is powered off or on, respectively. After the reference is powered off or on, the gain
register is again accessible to change the gain.
Table 7. DAC-n Selection for Gain Register Command
DB1, DB0
Value
DB0
0
DAC-A uses gain = 2 (default with internal reference)
1
DAC-A uses gain = 1 (default with external reference)
0
DAC-B uses gain = 2 (default with internal reference)
1
DAC-B uses gain = 1 (default with external reference)
DB1
Gain
8.4.3 Software Reset Function
The DAC756x, DAC816x, and DAC856x devices contain a software reset feature. The software reset function is
accessed by setting the serial interface command bits to 101. The software reset command contains two reset
modes which are software-programmable by setting bit DB0 in the shift register. Table 8 and Table 17 show the
available software reset commands.
Table 8. Software Reset
DB0
Registers Reset to Default Values
0
DAC registers
Input registers
1
DAC registers
Input registers
LDAC registers
Power-down registers
Internal reference register
Gain registers
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
33
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
8.4.4 Internal Reference Enable Register
The internal reference in the DAC756x, DAC816x, and DAC856x devices is disabled by default for debugging,
evaluation purposes, or when using an external reference. The internal reference can be powered up and
powered down by setting the serial interface command bits to 111 and configuring DB0 (see Table 9). The
internal reference is forced to a powered down state while both DAC channels are powered down, and can only
be enabled if any DAC channel is in normal mode of operation. During the time that the internal reference is
disabled, the DAC functions normally using an external reference. At this point, the internal reference is
disconnected from the VREFIN/VREFOUT pin (Hi-Z output).
Table 9. Internal Reference
DB0
Internal Reference Configuration
0
Disable internal reference and reset DACs to gain = 1
1
Enable internal reference and reset DACs to gain = 2
8.4.4.1 Enabling Internal Reference
To enable the internal reference, refer to the command structure in Table 17. When performing a power cycle to
reset the device, the internal reference is switched off (default mode). In the default mode, the internal reference
is powered down until a valid write sequence powers up the internal reference. However, the internal reference is
forced to a disabled state while both DAC channels are powered down, and remains disabled until either DAC
channel is returned to the normal mode of operation. See DAC Power-Down Commands for more information on
DAC channel modes of operation.
8.4.4.2 Disabling Internal Reference
To disable the internal reference, refer to the command structure in Table 17. When performing a power cycle to
reset the device, the internal reference is disabled (default mode).
8.4.5 CLR Functionality
The edge-triggered CLR pin can be used to set the input and DAC registers immediately according to Table 10.
When the CLR pin receives a falling edge signal the clear mode is activated and changes the DAC output
voltages accordingly. The device exits clear mode on the 24th falling edge of the next write to the device. If the
CLR pin receives a falling edge signal during a write sequence in normal operation, the clear mode is activated
and changes the input and DAC registers immediately according to Table 10.
Table 10. Clear Mode Reset Values
34
DEVICE
DAC Output Entering Clear Mode
DAC8562, DAC8162, DAC7562
Zero-scale
DAC8563, DAC8163, DAC7563
Mid-scale
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
8.4.6 LDAC Functionality
The DAC756x, DAC816x, and DAC856x devices offer both a software and hardware simultaneous update and
control function. The DAC double-buffered architecture has been designed so that new data can be entered for
each DAC without disturbing the analog outputs.
DAC756x, DAC816x, and DAC856x data updates can be performed either in synchronous or in asynchronous
mode.
In asynchronous mode, the LDAC pin is used as a negative edge-triggered timing signal for simultaneous DAC
updates. Multiple single-channel writes can be done in order to set different channel buffers to desired values
and then make a falling edge on LDAC pin to simultaneously update the DAC output registers. Data buffers of all
channels must be loaded with desired data before an LDAC falling edge. After a high-to-low LDAC transition, all
DACs are simultaneously updated with the last contents of the corresponding data buffers. If the content of a
data buffer is not changed, the corresponding DAC output remains unchanged after the LDAC pin is triggered.
LDAC must be returned high before the next serial command is initiated.
In synchronous mode, data are updated with the falling edge of the 24th SCLK cycle, which follows a falling edge
of SYNC. For such synchronous updates, the LDAC pin is not required, and it must be connected to GND
permanently or asserted and held low before sending commands to the device.
Alternatively, all DAC outputs can be updated simultaneously using the built-in software function of LDAC. The
LDAC register offers additional flexibility and control by allowing the selection of which DAC channel(s) should be
updated simultaneously when the LDAC pin is being brought low. The LDAC register is loaded with a 2-bit word
(DB1 and DB0) using command bits C2, C1, and C0 (see Table 17). The default value for each bit, and therefore
for each DAC channel, is zero. If the LDAC register bit is set to 1, it overrides the LDAC pin (the LDAC pin is
internally tied low for that particular DAC channel) and this DAC channel updates synchronously after the falling
edge of the 24th SCLK cycle. However, if the LDAC register bit is set to 0, the DAC channel is controlled by the
LDAC pin.
The combination of software and hardware simultaneous update functions is particularly useful in applications
when updating a DAC channel, while keeping the other channel unaffected; see Table 11 and Table 17 for more
information.
Table 11. DAC-n Selection for LDAC Register Command
DB1, DB0
Value
DB0
0
DAC-A uses LDAC pin
1
DAC-A operates in synchronous mode
0
DAC-B uses LDAC pin
1
DAC-B operates in synchronous mode
DB1
LDAC Pin Functionality
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
35
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
8.5 Programming
The DAC756x, DAC816x, and DAC856x devices have a three-wire serial interface (SYNC, SCLK, and DIN; see
the table) compatible with SPI, QSPI, and Microwire interface standards, as well as most DSPs. See the Serial
Write Operation timing diagram (Figure 1) for an example of a typical write sequence.
The DAC756x, DAC816x, or DAC856x input shift register is 24 bits wide, consisting of two don’t care bits (DB23
to DB22), three command bits (DB21 to DB19), three address bits (DB18 to DB16), and 16 data bits (DB15 to
DB0). All 24 bits of data are loaded into the DAC under the control of the serial clock input, SCLK. DB23 (MSB)
is the first bit that is loaded into the DAC shift register. DB23 is followed by the rest of the 24-bit word pattern,
left-aligned. This configuration means that the first 24 bits of data are latched into the shift register, and any
further clocking of data is ignored.
The write sequence begins by bringing the SYNC line low. Data from the DIN line are clocked into the 24-bit shift
register on each falling edge of SCLK. The serial clock frequency can be as high as 50 MHz, making the
DAC756x, DAC816x, and DAC856x devices compatible with high-speed DSPs. On the 24th falling edge of the
serial clock, the last data bit is clocked into the shift register and the shift register locks. Further clocking does not
change the shift register data.
After receiving the 24th falling clock edge, the DAC756x, DAC816x, and DAC856x devices decode the three
command bits, three address bits and 16 data bits to perform the required function, without waiting for a SYNC
rising edge. After the 24th falling edge of SCLK is received, the SYNC line may be kept low or brought high. In
either case, the minimum delay time from the 24th falling SCLK edge to the next falling SYNC edge must be met
in order to begin the next cycle properly; see the Serial Write Operation timing diagram (Figure 1).
A rising edge of SYNC before the 24-bit sequence is complete resets the SPI interface; no data transfer occurs.
A new write sequence starts at the next falling edge of SYNC. To assure the lowest power consumption of the
device, care should be taken that the levels are as close to each rail as possible.
8.5.1 SYNC Interrupt
In a normal write sequence, the SYNC line stays low for at least 24 falling edges of SCLK and the addressed
DAC register updates on the 24th falling edge. However, if SYNC is brought high before the 23rd falling edge, it
acts as an interrupt to the write sequence; the shift register resets and the write sequence is discarded. Neither
an update of the data buffer contents, DAC register contents, nor a change in the operating mode occurs (as
shown in Figure 93).
24th Falling Edge
24th Falling Edge
CLK
SYNC
DIN
DB23
DB23
DB0
Invalid/Interrupted Write Sequence:
Output/Mode Does Not Update on the Falling Edge
DB0
Valid Write Sequence:
Output/Mode Updates on the Falling Edge
Figure 93. SYNC Interrupt Facility
36
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Programming (continued)
8.5.2 DAC Register Configuration
When the DAC registers are being written to, the DAC756x, DAC816x, and DAC856x devices receive all 24 bits
of data, ignore DB23 and DB22, and decode the next three bits (DB21 to DB19) in order to determine the DAC
operating or control mode (see Table 12). Bits DB18 to DB16 are used to address the DAC channels (see
Table 13).
Table 12. Commands for the DAC756x, DAC816x, and DAC856x Devices
C2
(DB21)
C1
(DB20)
C0
(DB19)
0
0
0
Write to input register n (Table 13)
0
0
1
Software LDAC, update DAC register n (Table 13)
0
1
0
Write to input register n (Table 13) and update all DAC registers
0
1
1
Write to input register n and update DAC register n (Table 13)
1
0
0
Set DAC power up or -down mode
1
0
1
Software reset
1
1
0
Set LDAC registers
1
1
1
Enable or disable the internal reference
Command
Table 13. Address Select for the DAC756x, DAC816x, and DAC856x Devices
A2
(DB18)
A1
(DB17)
A0
(DB16)
0
0
0
DAC-A
0
0
1
DAC-B
0
1
0
Gain (only use with command 000)
0
1
1
Reserved
1
0
0
Reserved
1
0
1
Reserved
1
1
0
Reserved
1
1
1
DAC-A and DAC-B
Channel (n)
When writing to the DAC input registers the next 16, 14, or 12 bits of data that follow are decoded by the DAC to
determine the equivalent analog output (see Table 14 through Table 16) . The data format is straight binary, with
all 0s corresponding to 0-V output and all 1s corresponding to full-scale output. For all documentation purposes,
the data format and representation used here is a true 16-bit pattern (that is, FFFFh data word for full scale) that
the DAC756x, DAC816x, and DAC856x devices require.
Table 14. DAC856x Data Input Register Format
X (1) X
DB23
(1)
COMMAND
C2 C1 C0
ADDRESS
A2 A1 A0
D15 D14 D13 D12 D11 D10
D9
DATA
D8 D7
D6
D5
D4
D3
D2
D1
D0
DB0
D3
D2
D1
D0
X
X
DB0
D1
D0
X
X
X
X
DB0
X' denotes don't care bits.
Table 15. DAC816x Data Input Register Format
X
X
DB23
COMMAND
C2 C1 C0
ADDRESS
A2 A1 A0
COMMAND
C2 C1 C0
ADDRESS
A2 A1 A0
D13 D12 D11 D10
D9
D8
DATA
D7 D6
D5
D4
Table 16. DAC756x Data Input Register Format
X
X
DB23
D11 D10
Copyright © 2010–2015, Texas Instruments Incorporated
D9
D8
D7
DATA
D6 D5
D4
D3
D2
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
37
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
In additon to DAC input register updates, the DAC756x, DAC816x, and DAC856x devices support a number of
functional mode commands (such as write to LDAC register, power down DACs and so on). The complete set of
functional mode commands is shown in Table 17.
Table 17. Command Matrix for the DAC756x, DAC816x, and DAC856x Devices
Command
Address
DB23DB22
C2
C1
C0
X (1)
0
0
0
X
X
X
X
X
X
X
X
X
X
X
(1)
38
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
1
1
0
1
1
0
Data
DB15DB6
A0
0
0
0
16-, 14-, or 12-bit DAC data
Write to DAC-A input register
0
0
1
16-, 14-, or 12-bit DAC data
Write to DAC-B input register
1
1
1
16-, 14-, or 12-bit DAC data
Write to DAC-A and DAC-B input registers
0
0
0
16-, 14-, or 12-bit DAC data
Write to DAC-A input register and update all DACs
0
0
1
16-, 14-, or 12-bit DAC data
Write to DAC-B input register and update all DACs
1
1
1
16-, 14-, or 12-bit DAC data
Write to DAC-A and DAC-B input register and update all DACs
0
0
0
16-, 14-, or 12-bit DAC data
Write to DAC-A input register and update DAC-A
0
0
1
16-, 14-, or 12-bit DAC data
Write to DAC-B input register and update DAC-B
1
1
1
16-, 14-, or 12-bit DAC data
Write to DAC-A and DAC-B input register and update all DACs
0
0
0
X
Update DAC-A
0
0
1
X
Update DAC-B
1
1
1
X
0
1
X
0
X
0
X
0
X
1
X
0
X
1
X
0
DB4
DESCRIPTION
A1
0
DB5
DB3DB2
A2
DB1
DB0
Update all DACs
0
0
Gain: DAC-B gain = 2, DAC-A gain = 2 (default with internal VREF)
0
1
Gain: DAC-B gain = 2, DAC-A gain = 1
1
0
Gain: DAC-B gain = 1, DAC-A gain = 2
1
1
Gain: DAC-B gain = 1, DAC-A gain = 1 (power-on default)
0
1
Power up DAC-A
1
0
Power up DAC-B
1
1
Power up DAC-A and DAC-B
0
1
Power down DAC-A; 1 kΩ to GND
1
0
Power down DAC-B; 1 kΩ to GND
1
1
Power down DAC-A and DAC-B; 1 kΩ to GND
0
1
Power down DAC-A; 100 kΩ to GND
1
0
Power down DAC-B; 100 kΩ to GND
1
1
Power down DAC-A and DAC-B; 100 kΩ to GND
0
1
Power down DAC-A; Hi-Z
1
0
Power down DAC-B; Hi-Z
1
1
Power down DAC-A and DAC-B; Hi-Z
X
0
Reset DAC-A and DAC-B input register and update all DACs
X
1
Reset all registers and update all DACs (Power-on-reset update)
0
0
LDAC pin active for DAC-B and DAC-A
0
1
LDAC pin active for DAC-B; inactive for DAC-A
1
0
LDAC pin inactive for DAC-B; active for DAC-A
1
1
LDAC pin inactive for DAC-B and DAC-A
X
0
Disable internal reference and reset DACs to gain = 1
X
1
Enable internal reference and reset DACs to gain = 2
X
X
X
X
X
0
0
0
1
1
0
1
1
X
X
X
X
X
X
X
X denotes don't care bits.
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 DAC Internal Reference
The internal reference of the DAC756x, DAC816x, and DAC856x devices does not require an external load
capacitor for stability because it is stable without any capacitive load. However, for improved noise performance,
an external load capacitor of 150 nF or larger connected to the VREFIN/VREFOUT output is recommended. Figure 94
shows the typical connections required for operation of the DAC756x, DAC816x, and DAC856x internal
reference. A supply bypass capacitor at the AVDD input is also recommended.
DSC
DGS
150 nF
1
VOUTA
VREFIN/
10
VREFOUT
2
VOUTB
AVDD
9
3
GND
DIN
8
7
4
LDAC
SCLK
7
6
5
CLR
SYNC
6
1
VOUTA
VREFIN/VREFOUT
10
2
VOUTB
AVDD
9
3
GND
DIN
8
4
LDAC
SCLK
5
CLR
SYNC
AVDD
1 mF
150 nF
AVDD
1 mF
Figure 94. Typical Connections for Operating the DAC756x, DAC816x, and DAC856x Internal Reference
9.1.1.1 Supply Voltage
The internal reference features an extremely low dropout voltage. It can be operated with a supply of only 5 mV
above the reference output voltage in an unloaded condition. For loaded conditions, see the Load Regulation
section. The stability of the internal reference with variations in supply voltage (line regulation, dc PSRR) is also
exceptional. Within the specified supply voltage range of 2.7 V to 5.5 V, the variation at VREFIN/VREFOUT is
typically 50 μV/V; see Figure 7.
9.1.1.2 Temperature Drift
The internal reference is designed to exhibit minimal drift error, defined as the change in reference output voltage
over varying temperature. The drift is calculated using the box method described by Equation 3:
æ VREF _ MAX - VREF _ MIN ö
6
Drift Error = çç
÷÷ ´ 10 (ppm / °C )
´
V
T
REF
RANGE
è
ø
(3)
where:
VREF_MAX = maximum reference voltage observed within temperature range TRANGE.
VREF_MIN = minimum reference voltage observed within temperature range TRANGE.
VREF = 2.5 V, target value for reference output voltage.
TRANGE = the characterized range from –40°C to 125°C (165°C range)
The internal reference features an exceptional typical drift coefficient of 4 ppm/°C from –40°C to 125°C.
Characterizing a large number of units, a maximum drift coefficient of 10 ppm/°C is observed. Temperature drift
results are summarized in Figure 3.
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
39
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Application Information (continued)
9.1.1.3 Noise Performance
Typical 0.1-Hz to 10-Hz voltage noise and noise spectral density performance are listed in the Electrical
Characteristics. Additional filtering can be used to improve output noise levels, although care should be taken to
ensure the output impedance does not degrade the ac performance. The output noise spectrum at the
VREFIN/VREFOUT pin, both unloaded and with an external 4.7-µF load capacitor, is shown in Figure 6. Internal
reference noise impacts the DAC output noise when the internal reference is used.
9.1.1.4 Load Regulation
Load regulation is defined as the change in reference output voltage as a result of changes in load current. The
load regulation of the internal reference is measured using force and sense contacts as shown in Figure 95. The
force and sense lines reduce the impact of contact and trace resistance, resulting in accurate measurement of
the load regulation contributed solely by the internal reference. Measurement results are shown in Figure 4.
Force and sense lines should be used for applications that require improved load regulation.
Output Pin
Contact and
Trace Resistance
VOUT
Force Line
IL
Sense Line
Meter
Load
Figure 95. Accurate Load Regulation of the DAC756x, DAC816x, and DAC856x Internal Reference
9.1.1.4.1 Long-Term Stability
Long-term stability or aging refers to the change of the output voltage of a reference over a period of months or
years. This effect lessens as time progresses. The typical drift value for the internal reference is listed in the
Electrical Charateristics and measurement results are shown in Figure 5. This parameter is characterized by
powering up multiple devices and measuring them at regular intervals.
9.1.1.5 Thermal Hysteresis
Thermal hysteresis for a reference is defined as the change in output voltage after operating the device at 25°C,
cycling the device through the operating temperature range, and returning to 25°C. Hysteresis is expressed by
Equation 4:
é VREF_PRE - VREF_POST ù
6
VHYST = ê
ú ´ 10 (ppm/°C)
V
REF_NOM
ëê
ûú
(4)
where:
VHYST = thermal hysteresis.
VREF_PRE = output voltage measured at 25°C pre-temperature cycling.
VREF_POST = output voltage measured after the device cycles through the temperature range of –40°C to
aaa 125°C, and returns to 25°C.
VREF_NOM = 2.5 V, target value for reference output voltage.
9.1.2 DAC Noise Performance
Output noise spectral density at the VOUT-n pin versus frequency is depicted in Figure 45 and Figure 46 for fullscale, mid-scale, and zero-scale input codes. The typical noise density for mid-scale code is 90 nV/√Hz at 1 kHz.
High-frequency noise can be improved by filtering the reference noise. Integrated output noise between 0.1 Hz
and 10 Hz is close to 2.5 µVPP (mid-scale), as shown in Figure 47.
40
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
9.2 Typical Applications
9.2.1 Combined Voltage and Current Analog Output Module Using the XTR300
The design features two independent outputs that can source and sink voltage and current over the standard
industrial output ranges. The possible outputs of the design include: –24 mA to 24 mA, 4 mA–20 mA, 0 mA to 24
mA, 0 V to 5 V, 0 V to 10 V, –5 V to5 V, and –10 V to 10 V.
VREF R
SET
CCOMP
5.5 V
15 V
0.1 µF
–15 V
0.1 µF
0.1 µF
4.7 µF
RIMON
AVDD
LDAC
SCLK
VDAC
DAC8563
V+
V–
Current
Copy
ICOPY
RIN
IDRV DRV
VIN
VOUTA
DIN
XTR300
IMON
OPA
SET
SYNC
VOUTB
GND
+
CH2
VREFIN/
VREFOUT
VREF
RIA
IAOUT
IIA
IA
IAIN+
RG1
RG2
V or I OUTA
0 V to 5 V, 0 V to 10 V, –5 to 5 V,
–10 V to 10 V, –24 mA to 24 mA,
0 mA to 24 mA, 4mA to 20 mA
RG
GND
DGND
IAIN–
0.022 µF
Figure 96. DAC8563 and XTR300 Discrete Analog Output Module
9.2.1.1 Design Requirements
The design uses a DAC and a current-or-voltage output driver to create a discrete analog output design that can
output either voltage or current from the same pin while focusing on high-accuracy specifications. The choice of
the DAC8563 device takes advantage of its 16-bit resolution as well as its low typical offset error of 1 mV and
gain error of 0.01% FSR. The choice of the XTR300 device is based on its strong dc performance, having a
typical error of 400 µV and 0.04% FSR gain error. The XTR300 device allows a variety of both current and
voltage outputs on the same pin while providing load monitoring and error status pins.
The power-on reset-to-midscale feature of the DAC8563 makes the bipolar output of the XTR300 power up at 0
V or 0 A. If using a unipolar output, the recommended device to achieve a system power-on output of 0 V, 0 A or
4 mA is the DAC8562 device.
A recommendation for minimizing the introduction of errors into the system is to use ±0.01% tolerance RG and
RSET resistors. The bypass capacitors on AVDD, VREF, V+ and V– should have values between 100 nF and
10 µF. Smaller capacitors filter fast low-energy transients, whereas the large capacitors filter the slow highenergy transients. If there is an expectation of both types of signals in the system, the recommendation is to use
a pair of small and large values as shown on the AVDD pin of the DAC8563 device in Figure 96.
9.2.1.2 Detailed Design Procedure
When configured for voltage mode, the output of the instrumentation amplifier (IA), internal to the XTR300
device, is routed to the SET pin. The SET output provides feedback for the IA based on the IA input voltage. The
feedback from the IA provides high-impedance remote sensing of the voltage at the output load. Using the output
voltage can overcome errors from PCB traces and protection component impedances. The DAC provides a
unipolar input voltage to the VIN pin of the XTR300 device. The XTR300 device offsets the VDAC range by a
negative VREF and amplifies the difference by a value set by the RG and RSET resistors, as shown in Equation 5.
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
41
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Applications (continued)
VOUT =
æ VDAC - VREF
´ç
2 çè
R SET
RG
ö
÷
÷
ø
(5)
When configured for current mode, the XTR300 routes the internal output of its current copy circuitry to the SET
pin. This provides feedback for the internal OPA driver based on 1 / 10th of the output current, resulting in a
voltage-to-current transfer function. Generating bipolar current outputs from the single-ended DAC output
voltage, VDAC, requires the application of an offset to the XTR300 SET pin. Connect the RSET resistor from the
SET pin to VREF to apply the offset and obtain the transfer function shown in Equation 6.
æ VDAC - VREF ö
÷
I OUT = 10 ´ ç
ç
÷
R SET
è
ø
(6)
The desired output ranges for VDAC and VREF voltages determine the RSET and RG resistor values, calculated
using Equation 7 and Equation 8. The system design requires a VDAC voltage range of 0.04 V to 4.96 V in order
to operate the DAC8563 in the specified linear output range from codes 512 to 65 024.
æ V DAC - VREF ö
æ 4.96 V - 2.5 V ö
÷ = 10 ´ ç
RSET = 10 ´ ç
÷ = 1025 Ω
ç
÷
I OUT
0.024 A
è
ø
è
ø
(7)
2 ´ VOUT_MAX ´ R SET 2 ´ 10 V ´ 1020 Ω
RG =
=
= 8292 Ω
VDAC - VREF
4.96 V - 2.5 V
(8)
IMON and IAOUT accomplish load monitoring. The sizing of RIMON and RIA determine the monitoring output voltage
across the resistors. Size the resistors according to Equation 9 and Equation 10 and the expected output load
current IDRV.
10 ´ VIMON
R IMON =
IDRV
(9)
R IA =
10 ´ VIA
IIA
(10)
For more detailed information about the design procedure of this circuit and how to isolate it, see Two-Channel
Source/Sink Combined Voltage & Current Output, Isolated, EMC/EMI Tested Reference Design (TIDU434).
42
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
Typical Applications (continued)
9.2.1.3 Application Curves
Figure 97 shows the transfer function for the bipolar ±10 V voltage range. This design also supports output
voltage ranges of 0–5 V, 0–10 V and ±5 V. Figure 98 shows the transfer function for the unipolar 0–24 mA
current range. This design also supports output current ranges of ±24 mA and 4 mA–20 mA.
10
24
8
20
16
Output Current (mA )
Output Voltage (V )
6
4
2
0
-2
-4
-6
12
8
4
0
-4
-8
-12
-16
-8
-20
-24
-10
0
10k
20k
30k
40k
Input Code
50k
60k65535
Figure 97. Output Voltage vs Input Code
Copyright © 2010–2015, Texas Instruments Incorporated
D001
0
10k
20k
30k
40k
Input Code
50k
60k65535
D002
Figure 98. Output Current vs Input Code
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
43
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
Typical Applications (continued)
9.2.2 Up to ±15-V Bipolar Output Using the DAC8562
The DAC8562 is designed to be operate from a single power supply providing a maximum output range of AVDD
volts. However, the DAC can be placed in the configuration shown in Figure 99 in order to be designed into
bipolar systems. Depending on the ratio of the resistor values, the output of the circuit can range anywhere from
±5 V to ±15 V. The design example below shows that the DAC is configured to have its internal reference
enabled and the DAC8562 internal gain set to 2, however, an external 2.5-V reference could also be used (with
DAC8562 internal gain set to 2).
R
G´R
5.5 V
VREFOUT
18 V
R
+
DAC8562
VOUT
–
OPA140
G´R
–18 V
Figure 99. Bipolar Output Range Circuit Using DAC8562
The transfer function shown in Equation 5 can be used to calculate the output voltage as a function of the DAC
code, reference voltage and resistor ratio:
DIN
æ
ö
- 1÷
VOUT = G × VREFOUT ç 2 ×
65,536 ø
è
(11)
where:
DIN = decimal equivalent of the binary code that is loaded to the DAC register, ranging from 0 to 65,535 for
DAC8562 (16 bit).
VREFOUT = reference output voltage with the internal reference enabled from the DAC VREFIN/VREFOUT pin
G = ratio of the resistors
An example configuration to generate a ±10-V output range is shown below in Equation 6 with G = 4 and
VREFOUT = 2.5 V:
DIN
VOUT = 20 ×
- 10 V
65,536
(12)
In this example, the range is set to ±10 V by using a resistor ratio of four, VREFOUT of 2.5 V, and DAC8562
internal gain of 2. The resistor sizes must be selected keeping in mind the current sink or source capability of the
DAC8562 internal reference. Using larger resistor values, for example, R = 10 kΩ or larger, is recommended.
The op amp is selectable depending on the requirements of the system.
The DAC8562EVM and DAC7562EVM boards have the option to evaluate the bipolar output application by
installing the components on the pre-placed footprints. For more information see either the DAC8562EVM or
DAC7562EVM product folder.
44
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
9.3 System Examples
9.3.1 MSP430 Microprocessor Interfacing
Figure 100 shows a serial interface between the DAC756x, DAC816x, or DAC856x device and a typical MSP430
USI port such as the one found on the MSP430F2013. The port is configured in SPI master mode by setting bits
3, 5, 6, and 7 in USICTL0. The USI counter interrupt is set in USICTL1 to provide an efficient means of SPI
communication with minimal software overhead. The serial clock polarity, source, and speed are controlled by
settings in the USI clock control register (USICKCTL). The SYNC signal is derived from a bit-programmable pin
on port 1; in this case, port line P1.4 is used. When data are to be transmitted to the DAC756x, DAC816x, or
DAC856x device, P1.4 is taken low. The USI transmits data in 8-bit bytes; thus, only eight falling clock edges
occur in the transmit cycle. To load data to the DAC, P1.4 is left low after the first eight bits are transmitted; then,
a second write cycle is initiated to transmit the second byte of data. P1.4 is taken high following the completion of
the third write cycle.
MSP430F2013
DAC
P1.4/GPIO
SYNC
P1.5/SCLK
SCLK
P1.6/SDO
DIN
NOTE: Additional pins omitted for clarity.
Figure 100. DAC756x, DAC816x, or DAC856x Device to MSP430 Interface
9.3.2 TMS320 McBSP Microprocessor Interfacing
Figure 101 shows an interface between the DAC756x, DAC816x, or DAC856x device and any TMS320 series
DSP from Texas Instruments with a multi-channel buffered serial port (McBSP). Serial data are shifted out on the
rising edge of the serial clock and are clocked into the DAC756x, DAC816x, or DAC856x device on the falling
edge of the SCLK signal.
TMS320F28062
DAC
MFSxA
SYNC
MCLKxA
SCLK
MDxA
DIN
NOTE: Additional pins omitted for clarity.
Figure 101. DAC756x, DAC816x, or DAC856x Device to TMS320 McBSP Interface
9.3.3 OMAP-L1x Processor Interfacing
Figure 102 shows a serial interface between the DAC756x, DAC816x, or DAC856x device and the OMAP-L138
processor. The transmit clock CLKx0 of the L138 drives SCLK of the DAC756x, DAC816x, or DAC856x device,
and the data transmit (Dx0) output drives the serial data line of the DAC. The SYNC signal is derived from the
frame sync transmit (FSx0) line, similar to the TMS320 interface.
DAC
OMAP-L138
FSx0
SYNC
CLKx0
SCLK
Dx0
DIN
NOTE: Additional pins omitted for clarity.
Figure 102. DAC756x, DAC816x, or DAC856x Device to OMAP-L1x Processor
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
45
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
10 Power Supply Recommendations
These devices can operate within the specified supply voltage range of 2.7 V to 5.5 V. The power applied to
AVDD should be well-regulated and low-noise. In order to further minimize noise from the power supplies, a
strong recommendation is to include a pair of 100-pF and 1-nF capacitors and a 0.1-μF to 1-μF bypass
capacitor. The current consumption of the AVDD pin, the short-circuit current limit, and the load current for these
devices are listed in the Electrical Characteristics table. Choose the power supplies for these devices to meet the
aforementioned current requirements.
11 Layout
11.1 Layout Guidelines
A precision analog component requires careful layout, adequate bypassing, and clean, well-regulated power
supplies. The DAC756x, DAC816x, and DAC856x devices offer single-supply operation, and are often used in
close proximity with digital logic, microcontrollers, microprocessors, and digital signal processors. The more
digital logic present in the design and the higher the switching speed, the more difficult it is to keep digital noise
from appearing at the output. As a result of the single ground pin of the DAC756x, DAC816x, and DAC856x
devices, all return currents (including digital and analog return currents for the DAC) must flow through a single
point. Ideally, GND would be connected directly to an analog ground plane. This plane would be separate from
the ground connection for the digital components until they were connected at the power-entry point of the
system. The power applied to AVDD should be well-regulated and low noise. Switching power supplies and dc-dc
converters often have high-frequency glitches or spikes riding on the output voltage. In addition, digital
components can create similar high-frequency spikes as their internal logic switches states. This noise can easily
couple into the DAC output voltage through various paths between the power connections and analog output. As
with the GND connection, AVDD should be connected to a power-supply plane or trace that is separate from the
connection for digital logic until they are connected at the power-entry point. In addition, a pair of 100-pF to 1-nF
capacitors and a 0.1-µF to 1-µF bypass capacitor are strongly recommended. In some situations, additional
bypassing may be required, such as a 100-µF electrolytic capacitor or even a pi filter made up of inductors and
capacitors – all designed essentially to provide low-pass filtering for the supply and remove the high-frequency
noise.
46
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
www.ti.com
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
11.2 Layout Example
0.1 µF
Bypass Capacitors
100 pF
AVDD
DIN
Digital Lines
VREFIN/VREFOUT
SCLK
SYNC
GND
VOUTA
VOUTB
Digital Lines
Analog Lines
LDAC
CLK
Figure 103. DACxx6x Layout Example
Copyright © 2010–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
47
DAC7562, DAC7563, DAC8162
DAC8163, DAC8562, DAC8563
SLAS719E – AUGUST 2010 – REVISED JUNE 2015
www.ti.com
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 18. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
DAC7562
Click here
Click here
Click here
Click here
Click here
DAC7563
Click here
Click here
Click here
Click here
Click here
DAC8162
Click here
Click here
Click here
Click here
Click here
DAC8163
Click here
Click here
Click here
Click here
Click here
DAC8562
Click here
Click here
Click here
Click here
Click here
DAC8563
Click here
Click here
Click here
Click here
Click here
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
E2E is a trademark of Texas Instruments.
SPI, QSPI are trademarks of Motorola, Inc.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the mostcurrent data available for the designated devices. This data is subject to change without notice and without
revision of this document. For browser-based versions of this data sheet, see the left-hand navigation pane.
48
Submit Documentation Feedback
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DAC7562 DAC7563 DAC8162 DAC8163 DAC8562 DAC8563
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jan-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DAC7562SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7562
DAC7562SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7562
DAC7562SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7562
DAC7562SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
7562
DAC7563SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
7563
DAC7563SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
7563
DAC7563SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
7563
DAC7563SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
7563
DAC8162SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8162
DAC8162SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8162
DAC8162SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8162
DAC8162SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8162
DAC8163SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8163
DAC8163SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8163
DAC8163SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8163
DAC8163SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8163
DAC8562SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8562
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
23-Jan-2015
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DAC8562SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8562
DAC8562SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8562
DAC8562SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8562
DAC8563SDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8563
DAC8563SDGST
ACTIVE
VSSOP
DGS
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8563
DAC8563SDSCR
ACTIVE
WSON
DSC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8563
DAC8563SDSCT
ACTIVE
WSON
DSC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
8563
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jan-2015
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF DAC8562 :
• Automotive: DAC8562-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jan-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
DAC7562SDGSR
VSSOP
DGS
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC7562SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC7562SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC7562SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC7563SDGSR
VSSOP
DGS
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC7563SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC7563SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC7563SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8162SDGSR
VSSOP
DGS
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8162SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8162SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8162SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8163SDGSR
VSSOP
DGS
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8163SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8163SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8163SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8562SDGSR
VSSOP
DGS
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8562SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jan-2015
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC8562SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8562SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8563SDGSR
VSSOP
DGS
10
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8563SDGST
VSSOP
DGS
10
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
DAC8563SDSCR
WSON
DSC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
DAC8563SDSCT
WSON
DSC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7562SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC7562SDGST
VSSOP
DGS
10
250
195.0
200.0
45.0
DAC7562SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
DAC7562SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
DAC7563SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC7563SDGST
VSSOP
DGS
10
250
220.0
205.0
50.0
DAC7563SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
DAC7563SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
DAC8162SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC8162SDGST
VSSOP
DGS
10
250
220.0
205.0
50.0
DAC8162SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jan-2015
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC8162SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
DAC8163SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC8163SDGST
VSSOP
DGS
10
250
220.0
205.0
50.0
DAC8163SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
DAC8163SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
DAC8562SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC8562SDGST
VSSOP
DGS
10
250
220.0
205.0
50.0
DAC8562SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
DAC8562SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
DAC8563SDGSR
VSSOP
DGS
10
2500
370.0
355.0
55.0
DAC8563SDGST
VSSOP
DGS
10
250
220.0
205.0
50.0
DAC8563SDSCR
WSON
DSC
10
3000
367.0
367.0
35.0
DAC8563SDSCT
WSON
DSC
10
250
210.0
185.0
35.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated