TPSMA6.8 thru TPSMA43A Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Available in uni-directional polarity only • 400 W peak pulse power capability with a 10/1000 µs waveform, repetitive rate (duty cycle): 0.01 % DO-214AC (SMA) • Excellent clamping capability • Very fast response time • Low incremental surge resistance PRIMARY CHARACTERISTICS • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C VBR 6.8 V to 43 V PPPM 400 W • AEC-Q101 qualified • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC PD 1.0 W IFSM 40 A TJ max. 185 °C TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. MECHANICAL DATA Case: DO-214AC (SMA) Molding compound meets UL 94 V-0 flammability rating Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 HE3 suffix meets JESD 201 class 2 whisker test Polarity: Color band denotes cathode end MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER Peak power dissipation with a 10/1000 µs waveform (1)(2) (fig. 3) Peak power pulse current with a 10/1000 µs waveform (1) (fig. 1) Power dissipation at TA = 25 °C (4) Peak forward surge current 8.3 ms single half sine-wave (3) SYMBOL VALUE UNIT PPPM 400 W IPPM See next table A PD 1.0 W IFSM 40 A Maximum instantaneous forward voltage at 25 A (3) VF 3.5 V Operating junction and storage temperature range TJ, TSTG - 65 to + 185 °C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2 Mounted on P.C.B. with 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads attached to each terminal (3) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum (4) Mounted on minimum recommended pad layout (2) Document Number: 88405 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] www.vishay.com 1 TPSMA6.8 thru TPSMA43A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) DEVICE DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR (1) AT IT (V) MIN. TEST CURRENT IT (mA) STANDOFF VOLTAGE VWM (V) MAX. TJ = 150 °C MAXIMUM MAXIMUM REVERSE REVERSE LEAKAGE LEAKAGE AT AT VWM VWM IR (µA) ID (µA) MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) TPSMA6.8 ADP 6.12 7.48 10 5.50 300 1000 37.0 10.8 TPSMA6.8A AEP 6.45 7.14 10 5.80 300 1000 38.1 10.5 TPSMA7.5 AFP 6.75 8.25 10 6.05 150 500 34.2 11.7 TPSMA7.5A AGP 7.13 7.88 10 6.40 150 500 35.4 11.3 TPSMA8.2 AHP 7.38 9.02 10 6.63 50 200 32.0 12.5 TPSMA8.2A AKP 7.79 8.61 10 7.02 50 200 33.1 12.1 TPSMA9.1 ALP 8.19 10.00 1.0 7.37 10 50 29.0 13.8 TPSMA9.1A AMP 8.65 9.55 1.0 7.78 10 50 29.9 13.0 TPSMA10 ANP 9.00 11.00 1.0 8.10 5.0 20 26.7 15.0 TPSMA10A APP 9.50 10.50 1.0 8.65 5.0 20 27.6 14.5 TPSMA11 AQP 9.90 12.10 1.0 8.92 1.0 5.0 24.7 16.2 TPSMA11A ARP 10.50 11.60 1.0 9.40 1.0 5.0 25.6 15.6 TPSMA12 ASP 10.80 13.20 1.0 9.72 1.0 5.0 23.1 17.3 TPSMA12A ATP 11.40 12.60 1.0 10.20 1.0 5.0 24.0 16.7 TPSMA13 AUP 11.70 14.30 1.0 10.50 1.0 5.0 21.1 19.0 TPSMA13A AVP 12.40 13.70 1.0 11.10 1.0 5.0 22.0 18.2 TPSMA15 AWP 13.50 16.30 1.0 12.10 1.0 5.0 18.2 22.0 TPSMA15A AXP 14.30 15.80 1.0 12.80 1.0 5.0 18.9 21.2 TPSMA16 AYP 14.40 17.60 1.0 12.90 1.0 5.0 17.0 23.5 TPSMA16A AZP 15.20 16.80 1.0 13.60 1.0 5.0 17.8 22.0 TPSMA18 BDP 16.20 19.80 1.0 14.50 1.0 5.0 15.1 26.5 TPSMA18A BEP 17.10 18.90 1.0 15.30 1.0 5.0 15.9 25.5 TPSMA20 BFP 18.00 22.00 1.0 16.20 1.0 5.0 13.7 29.1 TPSMA20A BGP 19.00 21.00 1.0 17.10 1.0 5.0 14.4 27.7 TPSMA22 BHP 19.80 24.20 1.0 17.80 1.0 5.0 12.5 31.9 TPSMA22A BKP 20.90 23.10 1.0 18.80 1.0 5.0 13.1 30.6 34.7 TPSMA24 BLP 21.60 26.40 1.0 19.40 1.0 5.0 11.5 TPSMA24A BMP 22.80 25.20 1.0 20.50 1.0 5.0 12.0 33.2 TPSMA27 BNP 24.30 29.70 1.0 21.80 1.0 5.0 10.2 39.1 TPSMA27A BPP 25.70 28.40 1.0 23.10 1.0 5.0 10.7 37.5 TPSMA30 BQP 27.00 33.00 1.0 24.30 1.0 5.0 9.2 43.5 TPSMA30A BRP 28.50 31.50 1.0 25.60 1.0 5.0 9.7 41.4 TPSMA33 BSP 29.70 36.30 1.0 26.80 1.0 5.0 8.4 47.0 TPSMA33A BTP 31.40 34.70 1.0 28.20 1.0 5.0 8.8 45.7 TPSMA36 BUP 32.40 39.60 1.0 29.10 1.0 5.0 7.7 52.0 TPSMA36A BVP 34.20 37.80 1.0 30.80 1.0 5.0 8.0 49.9 TPSMA39 BWP 35.10 42.90 1.0 31.60 1.0 5.0 7.1 56.4 TPSMA39A BXP 37.10 41.00 1.0 33.30 1.0 5.0 7.4 53.9 TPSMA43 BYP 38.70 47.30 1.0 34.80 1.0 5.0 6.5 61.9 TPSMA43A BZP 40.90 45.20 1.0 36.80 1.0 5.0 6.7 59.3 Notes (1) VBR measured after IT applied for 300 µs, IT = square wave pulse or equivalent Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 (2) www.vishay.com 2 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] Document Number: 88405 Revision: 09-Feb-11 TPSMA6.8 thru TPSMA43A Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE TPSMA6.8AHE3/61T (1) 0.064 61T 1800 7" diameter plastic tape and reel TPSMA6.8AHE3/5AT (1) 0.064 5AT 7500 13" diameter plastic tape and reel Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 150 Non-Repetitive Pulse Waveform shown in Fig. 3 TA = 25 °C IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) 100 10 1.0 0.2 x 0.2" (5.0 x 5.0 mm) Copper Pad Areas 0.1 0.1 µs 10 µs 100 µs 1.0 ms Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td td 1.0 µs 0 10 ms 0 1.0 td - Pulse Width (s) 2.0 3.0 4.0 t - Time (ms) Figure 1. Peak Pulse Power Rating Curve Figure 3. Pulse Waveform 10 000 100 Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs 75 50 25 VR measured at Zero Bias 1000 VR measured at Stand-Off, VWM 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 0 0 50 100 150 200 1 10 100 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Figure 2. Pulse Power or Current vs. Initial Junction Temperature Figure 4. Typical Junction Capacitance Document Number: 88405 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] www.vishay.com 3 TPSMA6.8 thru TPSMA43A Vishay General Semiconductor Peak Forward Surge Current (A) 200 TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 1 5 10 50 100 Number of Cycles at 60 Hz Figure 5. Maximum Non-Repetitive Peak Forward Surge Current PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AC (SMA) Cathode Band Mounting Pad Layout 0.110 (2.79) 0.100 (2.54) 0.065 (1.65) 0.049 (1.25) 0.177 (4.50) 0.157 (3.99) 0.012 (0.305) 0.006 (0.152) 0.060 (1.52) MIN. 0.208 (5.28) REF. 0.090 (2.29) 0.078 (1.98) 0.060 (1.52) 0.030 (0.76) 0.074 (1.88) MAX. 0.066 (1.68) MIN. 0.008 (0.203) 0 (0) 0.208 (5.28) 0.194 (4.93) www.vishay.com 4 For technical questions within your region, please contact one of the following: [email protected], [email protected], [email protected] Document Number: 88405 Revision: 09-Feb-11 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1