PHILIPS 74ALS04BD

INTEGRATED CIRCUITS
74ALS04B
Hex inverter
Product specification
IC05 Data Handbook
1991 Feb 08
Philips Semiconductors
Product specification
Hex inverter
TYPE
74ALS04B
TYPICAL
PROPAGATION DELAY
TYPICAL
SUPPLY CURRENT
(TOTAL)
3.5ns
2.0mA
74ALS04B
PIN CONFIGURATION
1A
1
14
VCC
1Y
2
13
6A
2A
3
12
6Y
2Y
4
11
5A
3A
5
10
5Y
3Y
6
9
4A
GND
7
8
4Y
ORDERING INFORMATION
ORDER CODE
COMMERCIAL RANGE
VCC = 5V ±10%,
Tamb = 0°C to +70°C
DRAWING
NUMBER
14-pin plastic DIP
74ALS04BN
SOT27-1
14-pin plastic SO
74ALS04BD
SOT108-1
14-pin plastic SSOP
Type II
74ALS04BDB
SOT337-1
DESCRIPTION
SF00011
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS
DESCRIPTION
74ALS (U.L.)
HIGH/LOW
LOAD VALUE
HIGH/LOW
nA
Data input
1.0/1.0
20µA/0.1mA
nY
Data output
20/80
0.4mA/8mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
IEC/IEEE SYMBOL
1
1A
1A
VCC = Pin 14
GND = Pin 7
2
3
5
9
11 13
1
1
2
3
4
5
6
9
8
11
10
13
12
2A 3A 4A 5A 6A
2A 3A 4A 5A 6A
4
6
8
12
10
SF00013
SF00014
LOGIC DIAGRAM
1A
2A
3A
4A
5A
VCC = Pin 14
GND = Pin 7
6A
FUNCTION TABLE
1
2
3
4
5
6
9
8
11
10
13
12
INPUT
OUTPUT
nA
nY
L
H
H
L
1Y
2Y
3Y
H = High voltage level
L = Low voltage level
4Y
5Y
6Y
SF00012
1991 Feb 08
2
853–0856 01670
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
PARAMETER
SYMBOL
RATING
UNIT
V
VCC
Supply voltage
–0.5 to +7.0
VIN
Input voltage
–0.5 to +7.0
V
IIN
Input current
–30 to +5
mA
VOUT
Voltage applied to output in High output state
–0.5 to VCC
V
IOUT
Current applied to output in Low output state
16
mA
Tamb
Operating free-air temperature range
0 to +70
°C
Tstg
Storage temperature range
–65 to +150
°C
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
UNIT
MIN
NOM
MAX
5.0
5.5
VCC
Supply voltage
4.5
VIH
High-level input voltage
2.0
VIL
Low-level input voltage
0.8
V
IIk
Input clamp current
–18
mA
IOH
High-level output current
–0.4
mA
IOL
Low-level output current
8
mA
+70
°C
Tamb
Operating free-air temperature range
V
V
0
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
LIMITS
TEST CONDITIONS1
PARAMETER
MIN
VOH
High-level output voltage
VCC±10%, VIL = MAX, VIH = MIN, IOH = –0.4mA
VOL
O
Low level output voltage
Low-level
VCC = MIN,, VIL = MAX,,
VIH = MIN
VIK
Input clamp voltage
VCC = MIN, II = IIK
TYP2
UNIT
MAX
VCC – 2
V
IOL = 4mA
0.25
0.40
V
IOL = 8mA
0.35
0.50
V
-0.73
-1.5
V
II
Input current at maximum input voltage
VCC = MAX, VI = 7.0V
0.1
mA
IIH
High-level input current
VCC = MAX, VI = 2.7V
20
µA
IIL
Low-level input current
VCC = MAX, VI = 0.5V
-0.1
mA
IO
Output current3
VCC = MAX, VO = 2.25V
-112
mA
ICC
Supply current (total)
ICCH
ICCL
VCC = MAX
-30
VI = GND
0.75
1.1
mA
VI = 4.5V
3.2
4.2
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. The output conditions have been chosen to produce a current that closely approximate one half of the true short-circuit output current, IOS.
1991 Feb 08
3
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
tPLH
tPHL
Tamb = 0°C to +70°C
VCC = +5.0V ± 10%
CL = 50pF, RL = 500Ω
TEST CONDITION
Propagation delay
nA to nY
Waveform 1
MIN
MAX
2.0
2.0
11.0
8.0
UNIT
ns
AC WAVEFORMS
For all waveforms, VM = 1.3V.
nA
VM
VM
tPHL
tPLH
VM
nY
VM
SC00009
Waveform 1. Propagation Delay for Data to Output
TEST CIRCUIT AND WAVEFORMS
VCC
NEGATIVE
PULSE
VIN
CL
RL
AMP (V)
VM
10%
D.U.T.
RT
90%
VM
VOUT
PULSE
GENERATOR
tw
90%
10%
tTHL (tff)
tTLH (tr )
tTLH (tr )
tTHL (tf )
0.3V
AMP (V)
90%
Test Circuit for Totem-pole Outputs
POSITIVE
PULSE
90%
VM
VM
10%
10%
tw
0.3V
Input Pulse Definition
DEFINITIONS:
RL = Load resistor;
see AC electrical characteristics for value.
CL = Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
INPUT PULSE REQUIREMENTS
Family
Amplitude VM
74ALS
3.5V
1.3V
Rep.Rate
tw
tTLH
tTHL
1MHz
500ns
2.0ns
2.0ns
SC00005
1991 Feb 08
4
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
DIP14: plastic dual in-line package; 14 leads (300 mil)
1991 Feb 08
5
SOT27-1
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
SO14: plastic small outline package; 14 leads; body width 3.9 mm
1991 Feb 08
6
SOT108-1
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm
1991 Feb 08
7
SOT337-1
Philips Semiconductors
Product specification
Hex inverter
74ALS04B
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Formative or in Design
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
Preliminary Specification
Preproduction Product
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Product Specification
Full Production
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
 Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
1991 Feb 08
8
Date of release: 05-96