DAC1403D160 Dual 14 bits DAC, up to 160 MHz, 2 x interpolating Rev. 02 — 14 August 2008 Product data sheet 1. General description The DAC1403D160 is optimized to reduce architecture complexity and overall system cost. It leads to dynamic performance in multi-carrier support, because of its direct IF conversion capabilities. With an internal sampling rate of up to 160 MHz, DAC1403D160 is an extremely competitive solution for broadband wireless systems transmitters, as well as a wide range of applications. 2. Features n n n n n n n n n n Dual 14-bit resolution Spurious-Free Dynamic Range (SFDR) = 80 dBc at 2.5 MHz Input data rate up to 80 MHz 2 × interpolation filter Output data rate up to 160 MHz Single 3.3 V power supply Low noise capacitor-free integrated Phase-Locked Loup (PLL) Low power dissipation HTQFP80 package Ambient temperature from −40 °C to +85 °C 3. Applications n n n n n n Broadband wireless systems Digital radio links Cellular base stations Instrumentation Cable modem Cable Modem Termination System (CMTS)/Data Over Cable Service Interface Specification (DOCSIS) DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 4. Ordering information Table 1. Ordering information Type number DAC1403D160HW Package Name Description Version HTQFP80 plastic thermal enhanced thin quad flat package; 80 leads; body 12 × 12 × 1 mm; exposed die pad SOT841-1 5. Block diagram VCCA DAC1403D160 I13 to I0 11 to 16, 19 to 24, 27, 28 LATCH 14 14 FIR 14 U/I 60 73 72 DAC IVIRES IOUT IOUTN (CLK × 2) CLK CLKN Q13 to Q0 i.c. VCCD 5 CLOCK DRIVER 6 PLL (CLK × 2) INTERNAL BAND GAP (CLK × 2) 31 to 34, 37 to 42, 45 to 48 LATCH 14 14 FIR 14 57 69 68 DAC U/I 2, 8 10, 51 58 59 GAPOUT GAPD QOUT QOUTN QVIRES VCCA (1) VCCA (2) (3) (4) AGND DGND DEC 014aaa509 (1) Pins 1, 3, 61, 65, 76 and 80. (2) Pins 4, 7, 62, 64, 66, 67, 70, 71, 74, 75, 77 and 79. (3) Pins 9, 17, 25, 29, 30, 35, 44, 49, 50, 52, 53, 54, 55 and 56. (4) Pins 18, 26, 36, 43, 63 and 78. Fig 1. Block diagram DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 2 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 6. Pinning information 61 VCCA 62 AGND 63 DEC 65 VCCA 64 AGND 66 AGND 67 AGND 68 QOUTN 69 QOUT 70 AGND 71 AGND 72 IOUTN 73 IOUT 74 AGND 76 VCCA 75 AGND 77 AGND 78 DEC 80 VCCA 79 AGND 6.1 Pinning VCCA 1 60 IVIRES i.c. 2 59 QVIRES VCCA 3 58 GAPOUT AGND 4 57 GAPD CLK 5 56 DGND CLKN 6 55 DGND AGND 7 54 DGND i.c. 8 53 DGND DGND 9 52 DGND VCCD 10 51 VCCD DAC1403D160HW I13 11 50 DGND I12 12 49 DGND I11 13 48 Q0 I10 14 47 Q1 I9 15 46 Q2 DGND I8 16 45 Q3 DGND 17 44 DGND DEC 18 43 DEC Q6 40 Q7 39 Q8 38 Q9 37 DEC 36 DGND 35 Q10 34 Q11 33 Q12 32 Q13 31 DGND 30 DGND 29 I0 28 I1 27 DEC 26 DGND 25 I2 24 I3 23 41 Q5 I4 22 42 Q4 I6 20 I5 21 I7 19 014aaa510 Fig 2. Pin configuration 6.2 Pin description Table 2. Pin description Symbol Pin Type[1] Description VCCA 1 S analog supply voltage i.c. 2 I/O internally connected; leave open VCCA 3 S analog supply voltage AGND 4 G analog ground CLK 5 I clock input CLKN 6 I complementary clock input AGND 7 G analog ground i.c. 8 O internally connected; leave open DGND 9 G digital ground DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 3 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating Table 2. Pin description …continued Symbol Pin Type[1] Description VCCD 10 S digital supply voltage I13 11 I I data input bit 13 (Most Significant Bit (MSB)) I12 12 I I data input bit 12 I11 13 I I data input bit 11 I10 14 I I data input bit 10 I9 15 I I data input bit 9 I8 16 I I data input bit 8 DGND 17 G digital ground DEC 18 O decoupling node I7 19 I I data input bit 7 I6 20 I I data input bit 6 I5 21 I I data input bit 5 I4 22 I I data input bit 4 I3 23 I I data input bit 3 I2 24 I I data input bit 2 DGND 25 G digital ground DEC 26 O decoupling node I1 27 I I data input bit 1 I0 28 I I data input bit 0 (Least Significant Bit (LSB)) DGND 29 G digital ground DGND 30 G digital ground Q13 31 I Q data input bit 13 (MSB) Q12 32 I Q data input bit 12 Q11 33 I Q data input bit 11 Q10 34 I Q data input bit 10 DGND 35 G digital ground DEC 36 O decoupling node Q9 37 I Q data input bit 9 Q8 38 I Q data input bit 8 Q7 39 I Q data input bit 7 Q6 40 I Q data input bit 6 Q5 41 I Q data input bit 5 Q4 42 I Q data input bit 4 DEC 43 O decoupling node DGND 44 G digital ground Q3 45 I Q data input bit 3 Q2 46 I Q data input bit 2 Q1 47 I Q data input bit 1 Q0 48 I Q data input bit 0 (LSB) DGND 49 G digital ground DGND 50 G digital ground DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 4 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating Table 2. Pin description …continued Symbol Pin Type[1] Description VCCD 51 S digital supply voltage DGND 52 G digital ground DGND 53 G digital ground DGND 54 G digital ground DGND 55 G digital ground DGND 56 G digital ground GAPD 57 I internal band gap power disable input GAPOUT 58 I/O band gap output voltage QVIRES 59 I Q DAC biasing resistor IVIRES 60 I I DAC biasing resistor VCCA 61 S analog supply voltage AGND 62 G analog ground DEC 63 O decoupling node AGND 64 G analog ground VCCA 65 S analog supply voltage AGND 66 G analog ground AGND 67 G analog ground QOUTN 68 O complementary Q DAC output current QOUT 69 O Q DAC output current AGND 70 G analog ground AGND 71 G analog ground IOUTN 72 O complementary I DAC output current IOUT 73 O I DAC output current AGND 74 G analog ground AGND 75 G analog ground VCCA 76 S analog supply voltage AGND 77 G analog ground DEC 78 O decoupling node AGND 79 G analog ground VCCA 80 S analog supply voltage [1] Type description: S: Supply; G: Ground; I: Input; O: Output. DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 5 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 7. Functional description The Digital-to-Analog Converter (DAC) is a segmented architecture composed of a 7-bit thermometer sub-DAC and the remaining 7-bit in a binary weighted sub-DAC. The device produces two complementary current outputs on both channels, respectively pins IOUT/IOUTN and QOUT/QOUTN which need to be connected via a load resistor to the ground. Figure 3 shows the equivalent analog output circuit of one DAC, which consists of a parallel combination of PMOS current sources and associated switches for each segment. The cascade source configuration enables the increasing of the output impedance of the source and set to improve the dynamic performance of the DAC by introducing less distortion. Figure 4 shows the internal reference configuration. In this case the bias current is given by the output of the internal regulator connected to the inverting input of the internal operational amplifiers, while external resistors RI and RQ are connected respectively to pins IVIRES and QVIRES. Thus the output current of the two DACs is typically fixed to 20 mA with an appropriate choice of these resistors. This configuration is optimal for temperature drift compensation because the band gap can be matched with the voltage on the feedback resistors. The relation between full-scale output current IO(fs) and the RI (RQ) is: 2048 × V GAPOUT R I = ------------------------------------------ Ω 82 × I O ( fs ) The output current can also be adjusted by imposing an external reference voltage to the inverting input pin GAPOUT and disabling the internal band gap with pin GAPD set to HIGH. At a voltage lower than 1.2 V the current can be set at values lower than 20 mA. The input references at pins IVIRES and QVIRES may also be driven by separate reference voltages to adjust independently the two DAC currents. DAC1403D160 GAPD INTERNAL BAND GAP AGND GAPOUT DAC1403D160 IOUT/QOUT RL AGND RI IVIRES I DAC current sources array RQ QVIRES Q DAC current sources array IOUTN/QOUTN RL AGND 014aaa514 Fig 3. Equivalent analog output circuit 014aaa515 Fig 4. Internal reference configuration DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 6 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 8. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit −0.3 +3.9 V −0.3 +3.9 V VCCD digital supply voltage [1] VCCA analog supply voltage [1] ∆VCC supply voltage difference VCCA − VCCD −150 +150 mV VI input voltage pins Qn and In referenced to DGND −0.3 VCCD + 0.3 V pins IVIRES, QVIRES and GAPD referenced to AGND −0.3 VCCA + 0.3 V pins CLK and CLKN referenced to AGND −0.3 VCCA + 0.3 V pins IOUT, IOUTN, QOUT and QOUTN referenced to AGND −0.3 VCCA + 0.3 V VO output voltage Tstg storage temperature −55 +150 °C Tamb ambient temperature −40 +85 °C Tj junction temperature - 125 °C [1] All supplies are connected together. 9. Thermal characteristics Table 4. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient in free air 27.1 K/W Rth(c-a) thermal resistance from case to ambient in free air 11.8 K/W DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 7 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 10. Characteristics Table 5. Characteristics VCCD = VCCA = 3.0 V to 3.6 V; AGND and DGND connected together; Tamb = −40 °C to +85 °C; typical values measured at VCCD = VCCA = 3.3 V, IO(fs) = 20 mA and Tamb = 25 °C; dynamic parameters measured using output schematic given in Figure 10; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Supplies VCCD digital supply voltage 3.0 3.3 3.6 V VCCA analog supply voltage 3.0 3.3 3.6 V ICCD digital supply current - 55 65 mA ICCA analog supply current - 73 85 mA Ptot total power dissipation - 422 540 mW fclk = 80 MHz; fIOUT = fQOUT = 5 MHz Clock inputs (CLK and CLKN) VI(cm) common-mode input voltage - 1.65 - V Vi(dif)(p-p) peak-to-peak differential input voltage - 1.0 - V Analog outputs (IOUT, IOUTN, QOUT and QOUTN) IO(fs) Ro Co full-scale output current differential outputs 4 - 20 mA output resistance [1] - 150 - kΩ output capacitance [1] - 3 - pF - 0.3 VCCD V Digital inputs (I0 to I13, Q0 to Q13 and GAPD) VIL LOW-level input voltage DGND VIH HIGH-level input voltage 0.7 VCCD - VCCD V IIL LOW-level input current VIL = 0.3 VCCD - 5 - µA IIH HIGH-level input current VIH = 0.7 VCCD - 5 - µA - 1.31 - V Reference voltage output (GAPOUT) VGAPOUT voltage on pin GAPOUT IGAPOUT current on pin GAPOUT ∆VGAPOUT voltage variation on pin GAPOUT external voltage - 1 - µA - ±133 - ppm/°C Clock timing inputs (CLK and CLKN) fclk clock frequency - - 80 MHz tw(clk)H HIGH clock pulse width 5 - - ns tw(clk)L LOW clock pulse width 5 - - ns Input timing (I0 to I13 and Q0 to Q13); see Figure 5 th(i) input hold time 1.1 - 3.4 ns tsu(i) input set-up time −1.5 - +0.7 ns - 43 - ns Output timing (IOUT, IOUTN, QOUT, QOutN) ts settling time to = ± 0.5 LSB DAC1403D160_2 Product data sheet [1] © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 8 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating Table 5. Characteristics …continued VCCD = VCCA = 3.0 V to 3.6 V; AGND and DGND connected together; Tamb = −40 °C to +85 °C; typical values measured at VCCD = VCCA = 3.3 V, IO(fs) = 20 mA and Tamb = 25 °C; dynamic parameters measured using output schematic given in Figure 10; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit - - 80 MHz Digital filter specification (FIR); order N = 42; see Figure 6 and 7 and Table 7 fdata data rate αripple(pb) pass-band ripple fdata/fclk; 0.005 dB attenuation - 0.405 - Bp power bandwidth fdata/fclk; 3 dB attenuation - 0.479 - αstpb stop-band attenuation fdata/fclk = 0.6 to 1 - 69 - dB td(grp) group delay time - 11TCLK - ns Analog signal processing Linearity INL integral non-linearity - ±2.9 - LSB DNL differential non-linearity - ±1.5 - LSB In(o) output noise current - 120 - pA/√Hz Eoffset offset error relative to full-scale - −0.3 - % EG gain error relative to full-scale −5.4 - +5.4 % ∆GIQ IQ gain mismatch between I and Q, relative to full-scale - ±0.2 - % fo = 2.5 MHz at 0 dBFS - 80 - dBc fo = 5 MHz at 0 dBFS - 72 - dBc fo = 13 MHz at 0 dBFS - 64 - dBc fo = 5 MHz - 73 - dBc fo = 13 MHz - 65 - dBc fo = 5 MHz - 88 - dBc fo = 13 MHz - 86 - dBc Spurious free dynamic range SFDR spurious free dynamic range fclk = 80 MHz; BW = Nyquist Harmonics α2H α3H second harmonic level third harmonic level Two-tone intermodulation IMD2 second-order intermodulation distortion fclk = 80 MHZ; fo 1 = 10 MHz; fo 2 = 12 MHz; BW = Nyquist - 65 - dBc IMD3 third-order intermodulation distortion fclk = 80 MHz; fo 1 = 10 MHz; fo 2 = 12 MHz - 84 - dBc THD total harmonic distortion fclk = 80 MHz; BW = Nyquist (Tamb = 25 °C) NSD noise spectral density fo = 2.5 MHz - 75 - dBc fo = 5 MHz 68 71 - dBc fo = 2.5 MHz - −155 - dBm/Hz fo = 5 MHz - −155 - dBm/Hz fo = 19 MHz - −153 - dBm/Hz fclk = 80 MHz DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 9 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating Table 5. Characteristics …continued VCCD = VCCA = 3.0 V to 3.6 V; AGND and DGND connected together; Tamb = −40 °C to +85 °C; typical values measured at VCCD = VCCA = 3.3 V, IO(fs) = 20 mA and Tamb = 25 °C; dynamic parameters measured using output schematic given in Figure 10; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fo = 2.5 MHz - 80 - dBc fo = 5 MHz 70 80 - dBc fo = 19 MHz - 78 - dBc Signal-to-noise ratio S/N signal-to-noise ratio ACPR [1] adjacent channel power ratio fclk = 80 MHz; BW = Nyquist baseband; 5 MHz channel spacing; BW = 3.84 MHz fo = 2.5 MHz - 69 - dBc fo = 20 MHz - 71 - dBc Guaranteed by design. Table 6. Band gap Band gap disable (GAPD) Band gap input/output (GAPOUT) Internal band gap LOW output (VGAPOUT = 1.2 V) enable HIGH input disable tsu(i) I0 to I13, Q0 to Q13 CLKN 50 % CLK th(i) IOUT/IOUTN, QOUT/QOUTN 014aaa511 Fig 5. Input timing diagram DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 10 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 014aaa512 20 014aaa513 0.6 output (dB) normalized output −20 0.4 −60 0.2 −100 0 −140 −0.2 −180 0 0.2 0.4 0.6 0.8 1.0 normalized frequency (fo/fclk) 0 30 40 Fig 7. FIR filter impulse response Interpolation FIR filter coefficient Coefficient Coefficient Value H(1) H(43) 10 H(2) H(42) 0 H(3) H(41) −31 H(4) H(40) 0 H(5) H(39) 69 H(6) H(38) 0 H(7) H(37) −138 H(8) H(36) 0 H(9) H(35) 248 H(10) H(34) 0 H(11) H(33) −419 H(12) H(32) 0 H(13) H(31) 678 H(14) H(30) 0 H(15) H(29) −1083 H(16) H(28) 0 H(17) H(27) 1776 H(18) H(26) 0 H(19) H(25) −3282 H(20) H(24) 0 H(21) H(23) 10364 H(22) - 16384 DAC1403D160_2 Product data sheet 20 t (sample) Fig 6. FIR filter frequency response Table 7. 10 © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 11 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 11. Application information AGND DAC1403D160 1 kΩ CLK 100 nF DAC1403D160 Rs 1 kΩ CLK VCCA VCCA 100 nF AGND 1 kΩ 1 kΩ CLKN Vth CLKN 100 nF 1 kΩ 100 nF 1 kΩ AGND AGND 014aaa516 Fig 8. Single-ended clock schematic Fig 9. Differential clock schematic DAC1403D160_2 Product data sheet 014aaa517 © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 12 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 50 Ω 50 Ω RL RL 1:1 1:1 AGND AGND AGND AGND C AGND AGND DGND DGND C DEC I7 DEC AGND AGND VCCA AGND AGND QOUTN QOUT AGND AGND IOUTN IOUT AGND AGND AGND VCCA DEC 9 52 10 51 DAC1403D160 11 50 49 12 13 48 14 47 15 46 16 45 17 44 18 43 19 42 41 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 I5 I6 53 C DGND IVIRES 1.5 kΩ QVIRES 1.5 kΩ GAPOUT GAPD C AGND DGND DGND DGND DGND DGND DGND VCCD DGND 3.3 V C DGND DGND Q0 Q1 Q2 Q3 DGND DEC C DGND Q4 Q5 Q6 I8 8 Q7 I9 54 Q8 I10 7 Q9 I11 55 DEC I12 6 DGND I13 56 Q10 3.3 V VCCD 5 Q11 C 57 Q12 DGND 4 Q13 DGND 58 DGND i.c. 3 DGND AGND 59 I0 CLKN AGND C 2 I1 CLK C 60 DEC AGND AGND C DGND C 3.3 V 3.3 V 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 I2 3.3 V C I3 VCCA AGND VCCA C i.c. C 1 I4 VCCA AGND AGND AGND AGND 3.3 V C 3.3 V 50 Ω C AGND AGND AGND 3.3 V 50 Ω 50 Ω VCCA 50 Ω C DGND DGND 014aaa518 All resistors are 1 % precision resistors. C = 100 nF. Fig 10. Application diagram DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 13 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 11.1 Alternative parts The following alternative parts are also available: Table 8. Alternative parts Type number Description DAC1203D160 Dual 12 bits DAC, with 2 × interpolating DAC1003D160 Dual 10 bits DAC, with 2 × interpolating [1] [1] 160 MHz 160 MHz Pin to pin compatible DAC1403D160_2 Product data sheet Sampling frequency [1] © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 14 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 12. Package outline HTQFP80: plastic thermal enhanced thin quad flat package; 80 leads; body 12 x 12 x 1 mm; exposed die pad SOT841-1 c y exposed die pad X Dh A 60 41 61 ZE 40 e Eh E w (A 3) A A2 HE M θ bp A1 Lp L detail X pin 1 index 80 21 1 20 w bp e ZD M D v M A v M B B HD 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max A1 A2 A3 bp c D (1) Dh E (1) Eh e mm 1.2 0.15 0.05 1.05 0.95 0.25 0.27 0.17 0.20 0.09 12.1 11.9 6.05 5.95 12.1 11.9 6.05 5.95 0.5 HD HE 14.15 14.15 13.85 13.85 L Lp v w y 1 0.75 0.45 0.2 0.08 0.1 ZD(1) ZE(1) θ 1.45 1.05 7° 0° 1.45 1.05 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included OUTLINE VERSION SOT841-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 04-01-15 MS-026 Fig 11. Package outline SOT841-1 (HTQFP80) DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 15 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 13. Abbreviations Table 9. Abbreviations Acronym Description BW BandWidth FIR Finite Impulse Response IF Intermediate Frequency LSB Least Significant Bit MSB Most Significant Bit PLL Phase-Locked Loop PMOS Positive-Metal Oxide Semiconductor 14. Glossary 14.1 Static parameters DNL — Differential Non-Linearity. The difference between the ideal and the measured output value between successive DAC codes. INL — Integral Non-Linearity. The deviation of the transfer function from a best-fit straight line (linear regression computation). 14.2 Dynamic parameters IMD2 — Second-order intermodulation distortion. From a dual-tone digital input sine wave (these two frequencies are close together), the intermodulation distortion product IMD2 is the ratio of the RMS value of either tone and the RMS value of the worst 2nd-order intermodulation product. IMD3 — Third-order intermodulation distortion. From a dual-tone digital input sine wave (these two frequencies are close together), the intermodulation distortion product IMD3 is the ratio of the RMS value of either tone and the RMS value of the worst 3rd-order intermodulation product. S/N — Signal-to-Noise ratio. The ratio of the RMS value of the reconstructed output sine wave to the RMS value of the noise excluding the harmonics and the DC component. THD — Total Harmonic Distortion. The ratio of the RMS value of the harmonics of the output frequency to the RMS value of the output sine wave. Usually, the calculation of THD is done on the first 5 harmonics. SFDR — Spurious-Free Dynamic Range. The ratio of the RMS value of the reconstructed output sine wave and the RMS value of the largest spurious (harmonic and non-harmonic, excluding DC component) observed in the frequency domain. DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 16 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 15. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes DAC1403D160_2 20080814 Product data sheet - DAC1403D160_1 Modifications: DAC1403D160_1 • • • Corrections made to row Q0 in Table 2. Added condition & correction of value to ts in Table 5. Additional definition in Section 14. 20080616 Product data sheet DAC1403D160_2 Product data sheet - - © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 17 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] DAC1403D160_2 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 02 — 14 August 2008 18 of 19 DAC1403D160 NXP Semiconductors Dual 14 bits DAC, up to 160 MHz, 2 x interpolating 18. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 11.1 12 13 14 14.1 14.2 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 6 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal characteristics. . . . . . . . . . . . . . . . . . . 7 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Application information. . . . . . . . . . . . . . . . . . 12 Alternative parts . . . . . . . . . . . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Static parameters . . . . . . . . . . . . . . . . . . . . . . 16 Dynamic parameters. . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Contact information. . . . . . . . . . . . . . . . . . . . . 18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 14 August 2008 Document identifier: DAC1403D160_2