KEMET C0805C153J5GACTU

Product Bulletin
Surface Mount Ceramic Chip Capacitors –
Ultra-High Capacitance, C0G Dielectric
Outline Drawing
L
W
T
TIN PLATE
B
NICKEL PLATE
S
ELECTRODES
CONDUCTIVE METALLIZATION
Dimensions - Millimeters (Inches)
S
SEPARATION
minimum
MOUNTING
TECHNIQUE
0.20 (.008) -.40 (.016)
0.3 (.012)
Solder Reflow
0.35 (.014) ± .15 (.006)
0.7 (.028)
EIA SIZE
CODE
METRIC
SIZE CODE
0402
1005
1.0 (.04) ± .05 (.002)
0.5 (.02) ± .05 (.002)
0603
1608
1.6 (.063) ± .15 (.006)
0.8 (.032) ± .15 (.006)
0805
2012
2.0 (.079) ± .20 (.008)
1.25 (.049) ± .20 (.008)
0.50 (.02) ± .25 (.010)
0.75 (.030)
1206
3216
3.2 (.126) ± .20 (.008)
1.6 (.063) ± .20 (.008)
0.50 (.02) ± .25 (.010)
N/A
1210
3225
3.2 (.126) ± .20 (.008)
2.5 (.098) ± .20 (.008)
0.50 (.02) ± .25 (.010)
N/A
L - LENGTH
W - WIDTH
B - BANDWIDTH
Solder Wave +
or
Solder Reflow
See Capacitance Value Chart below for thickness dimension.
+ For extended values 1210 case sizes - solder reflow only. (Refer to F3102 catalog for additional soldering information and recommendations.)
Ordering Information
C 0805
C
103
Style
C - Ceramic
Size Code
0402, 0603, 0805, 1206, 1210
Specification
C - Standard
Capacitance Code, pF
First two digits represent significant figures.
Third digit specifies number of zeros. 100 pF = 101.
(Use “9” for 1.0 through 9.9 pF)
(Use “8” for 0.1 through .99 pF)
Capacitance Tolerance
F = ±1%
K = ±10%
G = ±2%
M = ±20%
J = ±5%
K
5
G
A
C
End Metallization
C = Standard (Tin-plate
nickel barrier)
Failure Rate Level
A = Not Applicable
Temperature Characteristic
Designated by Capacitance
Change Over Temperature Range
G = C0G (NP0) (±30 PPM/°C)
8 = 10V
4 = 16V
3 = 25V
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Voltage
5 = 50V
1 = 100V
F9200 11/07
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for C0G, with following specific requirements based on room
temperature (25°C) parameters:
• Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 30 PPM/°C over that range.
• Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 1000 megohm microfarads or
100GΩ, whichever is less.
• Capacitance and Dissipation Factor (DF) measured at the following conditions.
Capacitance - 1 kHz and 1 vrms if capacitance >1000 pF
1 MHz and 1 vrms if capacitance ≤ 1000 pF
DF Limit is 0.1%.
Soldering Process
Components are suitable for wave and IR reflow soldering except extended 1210 values which are suitable
for IR reflow only. All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of
pure tin to provide excellent solderability as well as resistance to leaching. (Please refer to KEMET catalog
F3102 for additional soldering information and recommendations.)
Marking
These chips will be supplied unmarked. However, marking is available as an extra cost option.
Qualification/Certification
AEC-Q200 Rev. C - Automotive
RoHS 6/6 - 100% tin termination
In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors.
The information in this bulletin supplements that in the catalog.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Ratings & Part Number Table - 0402 Case Size
Capacitance
Value (pF)
KEMET Part Number
Voltage
1100
1200
1300
1500
1600
1800
2000
2200
1100
1200
1300
1500
1600
1800
2000
2200
1100
1200
1300
1500
1600
1800
2000
2200
360
390
430
470
510
560
620
680
750
820
910
1000
1100
1200
1300
1500
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
1000
C0402C112_8GAC
C0402C122_8GAC
C0402C132_8GAC
C0402C152_8GAC
C0402C162_8GAC
C0402C182_8GAC
C0402C202_8GAC
C0402C222_8GAC
C0402C112_4GAC
C0402C122_4GAC
C0402C132_4GAC
C0402C152_4GAC
C0402C162_4GAC
C0402C182_4GAC
C0402C202_4GAC
C0402C222_4GAC
C0402C112_3GAC
C0402C122_3GAC
C0402C132_3GAC
C0402C152_3GAC
C0402C162_3GAC
C0402C182_3GAC
C0402C202_3GAC
C0402C222_3GAC
C0402C361_5GAC
C0402C391_5GAC
C0402C431_5GAC
C0402C471_5GAC
C0402C511_5GAC
C0402C561_5GAC
C0402C621_5GAC
C0402C681_5GAC
C0402C751_5GAC
C0402C821_5GAC
C0402C911_5GAC
C0402C102_5GAC
C0402C112_5GAC
C0402C122_5GAC
C0402C132_5GAC
C0402C152_5GAC
C0402C101_1GAC
C0402C111_1GAC
C0402C121_1GAC
C0402C131_1GAC
C0402C151_1GAC
C0402C161_1GAC
C0402C181_1GAC
C0402C201_1GAC
C0402C221_1GAC
C0402C241_1GAC
C0402C271_1GAC
C0402C301_1GAC
C0402C331_1GAC
C0402C361_1GAC
C0402C391_1GAC
C0402C431_1GAC
C0402C471_1GAC
C0402C511_1GAC
C0402C561_1GAC
C0402C621_1GAC
C0402C681_1GAC
C0402C751_1GAC
C0402C821_1GAC
C0402C911_1GAC
C0402C102_1GAC
10
10
10
10
10
10
10
10
16
16
16
16
16
16
16
16
25
25
25
25
25
25
25
25
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Capacitance
Tolerance
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
F,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
G,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
J,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
K,
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
Thickness - mm
(inches)
Qty
7" Reel
Qty
13" Reel
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
(0.02)
50,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
50,000
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
±
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
0.05
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
(0.002)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Ratings & Part Number Table - 0603 Case Size
Capacitance
Value (pF)
KEMET Part Number
Voltage
Capacitance
Tolerance
Thickness - mm
(inches)
Qty
7" Reel
Qty
13" Reel
12000
C0603C123_8GAC
10
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
15000
C0603C153_8GAC
10
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
12000
C0603C123_4GAC
16
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
15000
C0603C153_4GAC
16
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
12000
C0603C123_3GAC
25
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
15000
C0603C153_3GAC
25
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2200
C0603C222_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2400
C0603C242_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2700
C0603C272_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3000
C0603C302_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3300
C0603C332_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3600
C0603C362_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3900
C0603C392_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
4300
C0603C432_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
4700
C0603C472_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
5100
C0603C512_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
5600
C0603C562_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
6200
C0603C622_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
6800
C0603C682_5GAC
50
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
360
C0603C361_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
390
C0603C391_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
430
C0603C431_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
470
C0603C471_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
510
C0603C511_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
560
C0603C561_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
620
C0603C621_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
680
C0603C681_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
750
C0603C751_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
820
C0603C821_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
910
C0603C911_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1000
C0603C102_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1100
C0603C112_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1200
C0603C122_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1300
C0603C132_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1500
C0603C152_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1600
C0603C162_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
1800
C0603C182_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2000
C0603C202_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2200
C0603C222_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2400
C0603C242_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
2700
C0603C272_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3000
C0603C302_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3300
C0603C332_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3600
C0603C362_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
3900
C0603C392_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
4300
C0603C432_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
4700
C0603C472_1GAC
100
F, G, J, K, M
0.80 (0.031) ± 0.07 (0.003)
4,000
10,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Ratings & Part Number Table - 0805 Case Size
Capacitance
Value (pF)
KEMET Part Number
Voltage
Capacitance
Tolerance
Thickness - mm (inches)
Qty
7" Reel
Qty
13" Reel
47000
C0805C473_8GAC
10
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
47000
C0805C473_4GAC
16
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
47000
C0805C473_3GAC
25
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
6800
C0805C682_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
7500
C0805C752_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
8200
C0805C822_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
9100
C0805C912_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
10000
C0805C103_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
12000
C0805C123_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
15000
C0805C153_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
18000
C0805C183_5GAC
50
F, G, J, K, M
0.90 (0.035) ± 0.10 (0.004)
4,000
10,000
22000
C0805C223_5GAC
50
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
2200
C0805C222_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
2400
C0805C242_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
2700
C0805C272_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
3000
C0805C302_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
3300
C0805C332_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
3600
C0805C362_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
3900
C0805C392_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
4300
C0805C432_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
4700
C0805C472_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
5100
C0805C512_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
5600
C0805C562_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
6200
C0805C622_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
6800
C0805C682_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
7500
C0805C752_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
8200
C0805C822_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
9100
C0805C912_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
10000
C0805C103_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
12000
C0805C123_1GAC
100
F, G, J, K, M
1.00 (0.039) ± 0.10 (0.004)
2,500
10,000
15000
C0805C153_1GAC
100
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Ratings & Part Number Table - 1206 Case Size
Capacitance
Value (pF)
KEMET Part Number
Voltage
Capacitance
Tolerance
Thickness - mm
(inches)
Qty
7" Reel
Qty
13" Reel
15000
C1206C153_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
18000
C1206C183_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
22000
C1206C223_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
27000
C1206C273_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
33000
C1206C333_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
47000
C1206C473_5GAC
50
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
56000
C1206C563_5GAC
50
F, G, J, K, M
1.20 (0.047) ± 0.15 (0.006)
2,500
10,000
68000
C1206C683_5GAC
50
F, G, J, K, M
1.60 (0.063) ± 0.20 (0.008)
2,000
8,000
82000
C1206C823_5GAC
50
F, G, J, K, M
1.60 (0.063) ± 0.20 (0.008)
2,000
8,000
6800
C1206C682_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
7500
C1206C752_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
8200
C1206C822_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
9100
C1206C912_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
10000
C1206C103_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
12000
C1206C123_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
15000
C1206C153_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
18000
C1206C183_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
22000
C1206C223_1GAC
100
F, G, J, K, M
0.90 (0.035) ± 0.10 (0.004)
4,000
10,000
27000
C1206C273_1GAC
100
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
33000
C1206C333_1GAC
100
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
47000
C1206C473_1GAC
100
F, G, J, K, M
1.60 (0.063) ± 0.20 (0.008)
2,000
8,000
Ratings & Part Number Table - 1210 Case Size
Capacitance
Value (pF)
KEMET Part Number
Voltage
Capacitance
Tolerance
Thickness - mm
(inches)
Qty
7" Reel
Qty
13" Reel
18000
C1210C183_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
22000
C1210C223_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
27000
C1210C273_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
33000
C1210C333_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
47000
C1210C473_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
56000
C1210C563_5GAC
50
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
68000
C1210C683_5GAC
50
F, G, J, K, M
0.90 (0.035) ± 0.10 (0.004)
4,000
10,000
82000
C1210C823_5GAC
50
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
100000
C1210C104_5GAC
50
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
120000
C1210C124_5GAC
50
F, G, J, K, M
1.55 (0.061) ± 0.15 (0.006)
2,000
8,000
150000
C1210C154_5GAC
50
F, G, J, K, M
1.70 (0.067) ± 0.20 (0.008)
2,000
8,000
12000
C1210C123_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
15000
C1210C153_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
18000
C1210C183_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
22000
C1210C223_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
27000
C1210C273_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
33000
C1210C333_1GAC
100
F, G, J, K, M
0.78 (0.031) ± 0.10 (0.004)
4,000
10,000
47000
C1210C473_1GAC
100
F, G, J, K, M
1.00 (0.039) ± 0.10 (0.004)
2,500
10,000
56000
C1210C563_1GAC
100
F, G, J, K, M
1.10 (0.043) ± 0.10 (0.004)
2,500
10,000
68000
C1210C683_1GAC
100
F, G, J, K, M
1.25 (0.049) ± 0.15 (0.006)
2,500
10,000
82000
C1210C823_1GAC
100
F, G, J, K, M
1.55 (0.061) ± 0.15 (0.006)
2,000
8,000
100000
C1210C104_1GAC
100
F, G, J, K, M
1.70 (0.067) ± 0.20 (0.008)
2,000
8,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com