APTM20DHM16T3G Asymmetrical - Bridge MOSFET Power Module 13 VDSS = 200V RDSon = 16m typ @ Tj = 25°C ID = 104A @ Tc = 25°C 14 Application Welding converters Switched Mode Power Supplies Switched Reluctance Motor Drives Q1 CR3 18 22 7 23 8 19 Features Power MOS 7® MOSFETs - Low RDSon - Low input and Miller capacitance - Low gate charge - Avalanche energy rated - Very rugged Kelvin source for easy drive Very low stray inductance - Symmetrical design Internal thermistor for temperature monitoring High level of integration Q4 CR2 4 3 29 30 32 31 15 16 R1 28 27 26 25 23 22 20 19 18 29 16 30 15 31 14 Benefits Outstanding performance at high frequency operation Direct mounting to heatsink (isolated package) Low junction to case thermal resistance Solderable terminals both for power and signal for easy PCB mounting Low profile RoHS Compliant 13 32 2 3 4 7 8 10 11 12 All multiple inputs and outputs must be shorted together Example: 13/14 ; 29/30 ; 22/23 … Absolute maximum ratings ID IDM VGS RDSon PD IAR EAR EAS Parameter Drain - Source Breakdown Voltage Tc = 25°C Tc = 80°C Continuous Drain Current Pulsed Drain current Gate - Source Voltage Drain - Source ON Resistance Maximum Power Dissipation Avalanche current (repetitive and non repetitive) Repetitive Avalanche Energy Single Pulse Avalanche Energy Tc = 25°C Max ratings 200 104 77 416 ±30 19 390 104 50 3000 Unit V A V m W A mJ These Devices are sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. See application note APT0502 on www.microsemi.com www.microsemi.com 1–8 APTM20DHM16T3G – Rev 1 October, 2012 Symbol VDSS APTM20DHM16T3G All ratings @ Tj = 25°C unless otherwise specified Electrical Characteristics Symbol Characteristic IDSS RDS(on) VGS(th) IGSS Zero Gate Voltage Drain Current Drain – Source on Resistance Gate Threshold Voltage Gate – Source Leakage Current Test Conditions VGS = 0V,VDS = 200V VGS = 0V,VDS = 160V Min Typ Tj = 25°C Tj = 125°C VGS = 10V, ID = 52A VGS = VDS, ID = 2.5mA VGS = ±30 V, VDS = 0V 16 3 Max 250 1000 19 5 ±100 Unit Max Unit µA m V nA Dynamic Characteristics Symbol Ciss Coss Crss Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Test Conditions VGS = 0V VDS = 25V f = 1MHz Qg Total gate Charge 140 Qgs Gate – Source Charge Qgd Gate – Drain Charge VGS = 10V VBus = 100V ID =104A Td(on) Turn-on Delay Time Inductive switching @ 125°C VGS = 15V VBus = 133V ID = 104A RG = 5Ω 32 Tr Td(off) Rise Time Turn-off Delay Time Tf Fall Time Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Min Typ 7220 2330 146 pF nC 53 67 64 ns 88 116 Inductive switching @ 25°C VGS = 15V, VBus = 133V ID = 104A, RG = 5Ω 849 Inductive switching @ 125°C VGS = 15V, VBus = 133V ID = 104A, RG = 5Ω 936 µJ 929 µJ 986 Diode ratings and characteristics VRRM IRM Test Conditions Min IF DC Forward Current VF Diode Forward Voltage trr Reverse Recovery Time Qrr Reverse Recovery Charge Max 200 Maximum Peak Repetitive Reverse Voltage Maximum Reverse Leakage Current Typ VR=200V IF = 100A IF = 200A IF = 100A IF = 100A VR = 133V di/dt =200A/µs V Tj = 25°C Tj = 125°C Tc = 80°C 250 500 Tj = 125°C 100 1 1.4 0.9 Tj = 25°C 60 Tj = 125°C Tj = 25°C 110 200 Tj = 125°C 840 www.microsemi.com Unit µA A V ns nC 2–8 APTM20DHM16T3G – Rev 1 October, 2012 Symbol Characteristic APTM20DHM16T3G Thermal and package characteristics Symbol Characteristic RthJC VISOL TJ TSTG TC Torque Wt Min Junction to Case Thermal Resistance RMS Isolation Voltage, any terminal to case t =1 min, 50/60Hz Operating junction temperature range Storage Temperature Range Operating Case Temperature Mounting torque Package Weight Typ MOSFET diode To heatsink M4 4000 -40 -40 -40 2 Max 0.32 0.55 Unit °C/W V 150 125 100 3 110 °C N.m g Temperature sensor NTC (see application note APT0406 on www.microsemi.com for more information). Symbol R25 ∆R25/R25 B25/85 ∆B/B Characteristic Resistance @ 25°C Min T25 = 298.15 K TC=100°C RT R25 Typ 50 5 3952 4 Max Unit k % K % T: Thermistor temperature 1 1 RT: Thermistor value at T exp B25 / 85 T25 T See application note 1901 - Mounting Instructions for SP3 Power Modules on www.microsemi.com www.microsemi.com 3–8 APTM20DHM16T3G – Rev 1 October, 2012 SP3 Package outline (dimensions in mm) APTM20DHM16T3G Typical MOSFET Performance Curve Maximum Effective Transient Thermal Impedance, Junction to Case vs Pulse Duration Thermal Impedance (°C/W) 0.35 0.9 0.3 0.25 0.7 0.2 0.5 0.15 0.3 0.1 Single Pulse 0.1 0.05 0.05 0 0.00001 0.0001 0.001 0.01 0.1 1 10 rectangular Pulse Duration (Seconds) Low Voltage Output Characteristics 600 10V 500 9V 400 8.5V 300 8V 7.5V 200 7V 100 VDS > ID(on)xRDS(on)MAX 250µs pulse test @ < 0.5 duty cycle 250 200 150 100 TJ=25°C 50 TJ=125°C 6.5V 0 0 4 8 12 16 20 24 28 0 VDS, Drain to Source Voltage (V) Normalized to VGS=10V @ 52A 1.1 1 2 3 4 5 6 7 8 9 10 VGS, Gate to Source Voltage (V) DC Drain Current vs Case Temperature 120 RDS(on) vs Drain Current 1.2 ID, DC Drain Current (A) RDS(on) Drain to Source ON Resistance TJ=-55°C 0 VGS=10V 1 VGS=20V 0.9 100 80 60 40 20 0.8 0 0 25 50 75 100 125 150 ID, Drain Current (A) 25 50 75 100 125 150 TC, Case Temperature (°C) www.microsemi.com 4–8 APTM20DHM16T3G – Rev 1 October, 2012 ID, Drain Current (A) Transfert Characteristics 300 VGS=15V ID, Drain Current (A) 700 APTM20DHM16T3G 1.10 1.05 1.00 0.95 0.90 -50 -25 0 25 50 75 100 125 150 TJ, Junction Temperature (°C) Threshold Voltage vs Temperature 1.2 2.5 VGS=10V ID= 52A 2.0 1.5 1.0 0.5 0.0 -50 -25 1.1 1.0 0.9 0.8 0.7 0.6 25 50 75 100 125 150 Maximum Safe Operating Area limited by RDSon 100 100µs 1ms 10 Single pulse TJ=150°C TC=25°C 10ms 100ms 1 0 25 50 75 100 125 150 1 TC, Case Temperature (°C) VGS, Gate to Source Voltage (V) Capacitance vs Drain to Source Voltage 100000 Ciss 10000 Coss 1000 Crss 100 0 10 100 1000 VDS, Drain to Source Voltage (V) Gate Charge vs Gate to Source Voltage 14 ID=104A VDS=40V 12 TJ=25°C VDS=100V 10 10 20 30 40 50 VDS, Drain to Source Voltage (V) www.microsemi.com 8 VDS=160V 6 4 2 0 0 20 40 60 80 100 120 140 160 Gate Charge (nC) 5–8 APTM20DHM16T3G – Rev 1 October, 2012 -50 -25 C, Capacitance (pF) 0 TJ, Junction Temperature (°C) 1000 ID, Drain Current (A) VGS(TH), Threshold Voltage (Normalized) ON resistance vs Temperature RDS(on), Drain to Source ON resistance (Normalized) BVDSS, Drain to Source Breakdown Voltage (Normalized) Breakdown Voltage vs Temperature 1.15 APTM20DHM16T3G Delay Times vs Current Rise and Fall times vs Current 160 120 VDS=133V RG=5Ω TJ=125°C L=100µH 60 40 120 tr and tf (ns) td(on) 100 80 tr 60 40 20 0 0 0 25 0 50 75 100 125 150 175 ID, Drain Current (A) 3 VDS=133V RG=5Ω TJ=125°C L=100µH Eoff Switching Energy (mJ) 1.5 25 50 75 100 125 150 175 ID, Drain Current (A) Switching Energy vs Gate Resistance Switching Energy vs Current 2 Eon 1 0.5 Eoff 0 VDS=133V ID=104A TJ=125°C L=100µH 2.5 Eoff 2 1.5 Eon 1 0.5 0 25 50 75 100 125 150 175 0 ID, Drain Current (A) Operating Frequency vs Drain Current ZCS 150 VDS=133V D=50% RG=5Ω TJ=125°C TC=75°C 100 50 ZVS Hard switching 0 25 38 50 63 75 88 Source to Drain Diode Forward Voltage IDR, Reverse Drain Current (A) 250 200 5 10 15 20 25 30 35 40 45 50 Gate Resistance (Ohms) 300 Frequency (kHz) tf 1000 100 TJ=150°C TJ=25°C 10 100 ID, Drain Current (A) 1 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VSD, Source to Drain Voltage (V) www.microsemi.com 6–8 APTM20DHM16T3G – Rev 1 October, 2012 td(on) and td(off) (ns) td(off) 80 20 Eon and Eoff (mJ) VDS=133V RG=5Ω TJ=125°C L=100µH 140 100 APTM20DHM16T3G Typical Diode Performance Curve Maximum Effective Transient Thermal Impedance, Junction to Case vs Pulse Duration Thermal Impedance (°C/W) 0.6 0.9 0.5 0.7 0.4 0.5 0.3 0.2 0.3 0.1 0.1 0.05 Single Pulse 0 0.00001 0.0001 0.001 0.01 0.1 1 10 Rectangular Pulse Duration (Seconds) Forward Current vs Forward Voltage trr, Reverse Recovery Time (ns) 150 100 TJ=125°C TJ=25°C 50 0 0.0 0.5 1.0 TJ=125°C VR=133V 100 A 100 130 A 80 50 A 60 40 1.5 0 200 QRR vs. Current Rate Charge 2.00 100 A TJ=125°C VR=133V 1.75 130 A 50 A 1.50 1.25 1.00 0.75 0.50 0 200 400 600 800 1000 1200 IRRM, Reverse Recovery Current (A) QRR, Reverse Recovery Charge (µC) VF, Anode to Cathode Voltage (V) 1000 1200 IRRM vs. Current Rate of Charge 50 TJ=125°C VR=133V 40 100 A 130 A 50 A 30 20 10 0 0 200 400 -diF/dt (A/µs) 600 800 1000 1200 -diF/dt (A/µs) Capacitance vs. Reverse Voltage Max. Average Forward Current vs. Case Temp. 150 3200 2800 Duty Cycle = 0.5 TJ=150°C 125 2400 IF(AV) (A) C, Capacitance (pF) 400 600 800 -diF/dt (A/µs) 2000 1600 1200 100 75 50 800 25 400 0 0 1 10 100 1000 25 VR, Reverse Voltage (V) 50 75 100 125 150 Case Temperature (°C) www.microsemi.com 7–8 APTM20DHM16T3G – Rev 1 October, 2012 IF, Forward Current (A) Trr vs. Current Rate of Charge 120 200 APTM20DHM16T3G DISCLAIMER The information contained in the document (unless it is publicly available on the Web without access restrictions) is PROPRIETARY AND CONFIDENTIAL information of Microsemi and cannot be copied, published, uploaded, posted, transmitted, distributed or disclosed or used without the express duly signed written consent of Microsemi. If the recipient of this document has entered into a disclosure agreement with Microsemi, then the terms of such Agreement will also apply. This document and the information contained herein may not be modified, by any person other than authorized personnel of Microsemi. No license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducement, estoppels or otherwise. Any license under such intellectual property rights must be approved by Microsemi in writing signed by an officer of Microsemi. Microsemi reserves the right to change the configuration, functionality and performance of its products at anytime without any notice. This product has been subject to limited testing and should not be used in conjunction with lifesupport or other mission-critical equipment or applications. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express or implied warranty, relating to sale and/or use of Microsemi products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Any performance specifications believed to be reliable but are not verified and customer or user must conduct and complete all performance and other testing of this product as well as any user or customers final application. User or customer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the customer’s and user’s responsibility to independently determine suitability of any Microsemi product and to test and verify the same. The information contained herein is provided “AS IS, WHERE IS” and with all faults, and the entire risk associated with such information is entirely with the User. Microsemi specifically disclaims any liability of any kind including for consequential, incidental and punitive damages as well as lost profit. The product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp Life Support Application Seller's Products are not designed, intended, or authorized for use as components in systems intended for space, aviation, surgical implant into the body, in other applications intended to support or sustain life, or for any other application in which the failure of the Seller's Product could create a situation where personal injury, death or property damage or loss may occur (collectively "Life Support Applications"). Buyer agrees not to use Products in any Life Support Applications and to the extent it does it shall conduct extensive testing of the Product in such applications and further agrees to indemnify and hold Seller, and its officers, employees, subsidiaries, affiliates, agents, sales representatives and distributors harmless against all claims, costs, damages and expenses, and attorneys' fees and costs arising, directly or directly, out of any claims of personal injury, death, damage or otherwise associated with the use of the goods in Life Support Applications, even if such claim includes allegations that Seller was negligent regarding the design or manufacture of the goods. www.microsemi.com 8–8 APTM20DHM16T3G – Rev 1 October, 2012 Buyer must notify Seller in writing before using Seller’s Products in Life Support Applications. Seller will study with Buyer alternative solutions to meet Buyer application specification based on Sellers sales conditions applicable for the new proposed specific part.