APTC90DAM60T1G Boost chopper Super Junction MOSFET VDSS = 900V RDSon = 60m max @ Tj = 25°C ID = 59A @ Tc = 25°C Power Module 5 6 Application AC and DC motor control Switched Mode Power Supplies Power Factor Correction 11 CR1 3 4 Q2 Features NTC 9 10 1 2 12 - Ultra low RDSon - Low Miller capacitance - Ultra low gate charge - Avalanche energy rated - Very rugged Kelvin source for easy drive Very low stray inductance Internal thermistor for temperature monitoring High level of integration Benefits Outstanding performance at high frequency operation Direct mounting to heatsink (isolated package) Low junction to case thermal resistance Solderable terminals both for power and signal for easy PCB mounting Low profile RoHS Compliant Pins 1/2 ; 3/4 ; 5/6 must be shorted together Absolute maximum ratings ID IDM VGS RDSon PD IAR EAR EAS Parameter Drain - Source Breakdown Voltage Tc = 25°C Tc = 80°C Continuous Drain Current Pulsed Drain current Gate - Source Voltage Drain - Source ON Resistance Maximum Power Dissipation Avalanche current (repetitive and non repetitive) Repetitive Avalanche Energy Single Pulse Avalanche Energy Tc = 25°C Max ratings 900 59 44 150 ±20 60 462 8.8 2.9 1940 Unit V A V m W A mJ These Devices are sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. See application note APT0502 on www.microsemi.com www.microsemi.com 1–6 APTC90DAM60T1G – Rev 1 October, 2012 Symbol VDSS APTC90DAM60T1G All ratings @ Tj = 25°C unless otherwise specified Electrical Characteristics Symbol Characteristic IDSS RDS(on) VGS(th) IGSS Zero Gate Voltage Drain Current Drain – Source on Resistance Gate Threshold Voltage Gate – Source Leakage Current Test Conditions VGS = 0V,VDS = 900V VGS = 0V,VDS = 900V Min Typ 2.5 1000 50 3 Tj = 25°C Tj = 125°C VGS = 10V, ID = 52A VGS = VDS, ID = 6mA VGS = ±20 V, VDS = 0V Max 200 Unit 60 3.5 200 m V nA Max Unit µA Dynamic Characteristics Symbol Characteristic Ciss Input Capacitance Coss Output Capacitance Qg Total gate Charge Qgs Gate – Source Charge Qgd Gate – Drain Charge Td(on) Turn-on Delay Time Tr Td(off) Rise Time Turn-off Delay Time Tf Fall Time Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Test Conditions VGS = 0V ; VDS = 100V f = 1MHz Min Typ 13.6 0.66 nF 540 VGS = 10V VBus = 400V ID = 52A nC 64 230 70 Inductive Switching (125°C) VGS = 10V VBus = 600V ID = 52A RG = 3.8 20 ns 400 25 Inductive switching @ 25°C VGS = 10V ; VBus = 600V ID = 52A ; RG = 3.8 Inductive switching @ 125°C VGS = 10V ; VBus = 600V ID = 52A ; RG = 3.8 3 mJ 1.5 4.2 mJ 1.7 Chopper diode ratings and characteristics IRM IF VF Maximum Reverse Leakage Current Test Conditions VR=1000V DC Forward Current Diode Forward Voltage trr Reverse Recovery Time Qrr Reverse Recovery Charge IF = 60A IF = 120A IF = 60A IF = 60A VR = 667V di/dt =200A/µs www.microsemi.com Min 1000 Tj = 25°C Tj = 125°C Tc = 80°C Typ Max 100 500 Tj = 125°C Tj = 25°C 60 2.2 2.8 1.8 235 Tj = 125°C 305 Tj = 25°C 460 Tj = 125°C 2600 Unit V µA A 2.8 V ns nC 2–6 APTC90DAM60T1G – Rev 1 October, 2012 Symbol Characteristic VRRM Maximum Peak Repetitive Reverse Voltage APTC90DAM60T1G Thermal and package characteristics Symbol Characteristic RthJC VISOL TJ TSTG TC Torque Wt Min Junction to Case Thermal Resistance RMS Isolation Voltage, any terminal to case t =1 min, 50/60Hz Operating junction temperature range Storage Temperature Range Operating Case Temperature Mounting torque Package Weight Typ CoolMOS diode To heatsink M4 4000 -40 -40 -40 2 Max 0.27 0.9 Unit °C/W V 150 125 100 3 80 °C N.m g Temperature sensor NTC (see application note APT0406 on www.microsemi.com for more information). Symbol R25 ∆R25/R25 B25/85 ∆B/B Characteristic Resistance @ 25°C Min T25 = 298.15 K TC=100°C RT R25 Typ 50 5 3952 4 Max Unit k % K % T: Thermistor temperature 1 1 RT: Thermistor value at T exp B25 / 85 T25 T See application note 1904 - Mounting Instructions for SP1 Power Modules on www.microsemi.com www.microsemi.com 3–6 APTC90DAM60T1G – Rev 1 October, 2012 SP1 Package outline (dimensions in mm) APTC90DAM60T1G Typical CoolMOS Performance Curve Maximum Effective Transient Thermal Impedance, Junction to Case vs Pulse Duration Thermal Impedance (°C/W) 0.3 0.9 0.25 0.7 0.2 0.15 0.5 0.1 0.3 0.1 0.05 Single Pulse 0.05 0 0.00001 0.0001 0.001 0.01 0.1 1 10 rectangular Pulse Duration (Seconds) Low Voltage Output Characteristics 6V 160 5V 80 0 0 5 10 15 VDS, Drain to Source Voltage (V) 20 Maximum Safe Operating Area 10 ms ID, DC Drain Current (A) ID, Drain Current (A) 100 µs Single pulse TJ=150°C TC=25°C 950 925 900 25 75 100 125 50 40 30 20 10 1 0 1 10 100 1000 25 VDS, Drain to Source Voltage (V) Ciss 10000 Coss 1000 100 Crss 10 1 0 50 75 100 125 TC, Case Temperature (°C) 150 Gate Charge vs Gate to Source Voltage VGS, Gate to Source Voltage (V) Capacitance vs Drain to Source Voltage 100000 C, Capacitance (pF) 50 DC Drain Current vs Case Temperature 60 limited by RDSon 10 975 TJ, Junction Temperature (°C) 1000 100 1000 10 25 50 75 100 125 150 175 200 VDS, Drain to Source Voltage (V) www.microsemi.com VDS=400V ID=52A TJ=25°C 8 6 4 2 0 0 100 200 300 400 Gate Charge (nC) 500 600 4–6 APTC90DAM60T1G – Rev 1 October, 2012 ID, Drain Current (A) VGS=20, 8V BVDSS, Drain to Source Breakdown Voltage Breakdown Voltage vs Temperature 240 APTC90DAM60T1G VDS=600V D=50% RG=3.8Ω TJ=125°C TC=75°C 300 200 Hard switching 100 ZCS 0 20 25 30 35 40 45 50 3.0 2.5 2.0 1.5 1.0 0.5 25 ID, Drain Current (A) 6 Eon 4 Eoff 2 0 10 20 30 40 50 60 ID, Drain Current (A) 100 125 150 7 Switching Energy (mJ) Eon and Eoff (mJ) VDS=600V RG=3.8Ω TJ=125°C L=100µH 75 Switching Energy vs Gate Resistance Switching Energy vs Current 8 50 TJ, Junction Temperature (°C) 70 80 6 Eon 5 Eoff 4 3 VDS=600V ID=52A TJ=125°C L=100µH 2 1 0 0 5 10 15 20 Gate Resistance (Ohms) “COOLMOS™ comprise a new family of transistors developed by Infineon Technologies AG. “COOLMOS” is a trademark of Infineon Technologies AG”. www.microsemi.com 5–6 APTC90DAM60T1G – Rev 1 October, 2012 Frequency (kHz) ZVS ON resistance vs Temperature RDS(on), Drain to Source ON resistance (Normalized) Operating Frequency vs Drain Current 400 APTC90DAM60T1G DISCLAIMER The information contained in the document (unless it is publicly available on the Web without access restrictions) is PROPRIETARY AND CONFIDENTIAL information of Microsemi and cannot be copied, published, uploaded, posted, transmitted, distributed or disclosed or used without the express duly signed written consent of Microsemi. If the recipient of this document has entered into a disclosure agreement with Microsemi, then the terms of such Agreement will also apply. This document and the information contained herein may not be modified, by any person other than authorized personnel of Microsemi. No license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducement, estoppels or otherwise. Any license under such intellectual property rights must be approved by Microsemi in writing signed by an officer of Microsemi. Microsemi reserves the right to change the configuration, functionality and performance of its products at anytime without any notice. This product has been subject to limited testing and should not be used in conjunction with lifesupport or other mission-critical equipment or applications. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express or implied warranty, relating to sale and/or use of Microsemi products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Any performance specifications believed to be reliable but are not verified and customer or user must conduct and complete all performance and other testing of this product as well as any user or customers final application. User or customer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the customer’s and user’s responsibility to independently determine suitability of any Microsemi product and to test and verify the same. The information contained herein is provided “AS IS, WHERE IS” and with all faults, and the entire risk associated with such information is entirely with the User. Microsemi specifically disclaims any liability of any kind including for consequential, incidental and punitive damages as well as lost profit. The product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp Life Support Application Seller's Products are not designed, intended, or authorized for use as components in systems intended for space, aviation, surgical implant into the body, in other applications intended to support or sustain life, or for any other application in which the failure of the Seller's Product could create a situation where personal injury, death or property damage or loss may occur (collectively "Life Support Applications"). Buyer agrees not to use Products in any Life Support Applications and to the extent it does it shall conduct extensive testing of the Product in such applications and further agrees to indemnify and hold Seller, and its officers, employees, subsidiaries, affiliates, agents, sales representatives and distributors harmless against all claims, costs, damages and expenses, and attorneys' fees and costs arising, directly or directly, out of any claims of personal injury, death, damage or otherwise associated with the use of the goods in Life Support Applications, even if such claim includes allegations that Seller was negligent regarding the design or manufacture of the goods. www.microsemi.com 6–6 APTC90DAM60T1G – Rev 1 October, 2012 Buyer must notify Seller in writing before using Seller’s Products in Life Support Applications. Seller will study with Buyer alternative solutions to meet Buyer application specification based on Sellers sales conditions applicable for the new proposed specific part.