CY14B108L, CY14B108N 8-Mbit (1024 K × 8/512 K × 16) nvSRAM Datasheet.pdf

CY14B108L
CY14B108N
8-Mbit (1024 K × 8/512 K × 16) nvSRAM
8-Mbit (1024 K × 8/512 K × 16) nvSRAM
Features
■
Packages
❐ 44-/54-pin thin small outline package (TSOP) Type II
❐ 48-ball fine-pitch ball grid array (FBGA)
Pb-free and restriction of hazardous substances (RoHS)
compliant
■
20 ns, 25 ns, and 45 ns access times
■
Internally organized as 1024 K × 8 (CY14B108L) or 512 K ×16
(CY14B108N)
■
■
Hands off automatic STORE on power-down with only a small
capacitor
Functional Description
■
STORE to QuantumTrap nonvolatile elements initiated by
software, device pin, or AutoStore on power-down
■
RECALL to SRAM initiated by software or power-up
■
Infinite Read, Write, and RECALL cycles
■
1 million STORE cycles to QuantumTrap
■
20 year data retention
■
Single 3 V +20, –10 operation
■
Industrial temperature
The Cypress CY14B108L/CY14B108N is a fast static RAM
(SRAM), with a nonvolatile element in each memory cell. The
memory is organized as 1024 Kbytes of 8 bits each or 512 K
words of 16 bits each. The embedded nonvolatile elements
incorporate QuantumTrap technology, producing the world’s
most reliable nonvolatile memory. The SRAM provides infinite
read and write cycles, while independent nonvolatile data
resides in the highly reliable QuantumTrap cell. Data transfers
from the SRAM to the nonvolatile elements (the STORE
operation) takes place automatically at power-down. On
power-up, data is restored to the SRAM (the RECALL operation)
from the nonvolatile memory. Both the STORE and RECALL
operations are also available under software control.
For a complete list of related documentation, click here.
Logic Block Diagram [1, 2, 3]
Quatrum Trap
2048 X 2048 X 2
A0
A1
A2
A3
A4
A5
A6
A7
A8
A17
A18
A19
R
O
W
STORE
VCC
VCAP
POWER
CONTROL
RECALL
D
E
C
O
D
E
R
STATIC RAM
ARRAY
2048 X 2048 X 2
STORE/RECALL
CONTROL
SOFTWARE
DETECT
HSB
A14 - A2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
I
N
P
U
T
B
U
F
F
E
R
S
COLUMN I/O
OE
COLUMN DEC
WE
DQ12
DQ13
CE
DQ14
BLE
A9 A10 A11 A12 A13 A14 A15 A16
DQ15
BHE
Errata: AutoStore Disable feature does not work in the device. For more information, see Errata on page 24. Details include errata trigger conditions, scope of impact,
available workarounds, and silicon revision applicability.
Notes
1. Address A0–A19 for × 8 configuration and Address A0–A18 for × 16 configuration.
2. Data DQ0–DQ7 for × 8 configuration and Data DQ0–DQ15 for × 16 configuration.
3. BHE and BLE are applicable for × 16 configuration only.
Cypress Semiconductor Corporation
Document Number: 001-45523 Rev. *O
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 8, 2015
CY14B108L
CY14B108N
Contents
Pinouts .............................................................................. 3
Pin Definitions .................................................................. 4
Device Operation .............................................................. 5
SRAM Read ................................................................ 5
SRAM Write ................................................................. 5
AutoStore Operation .................................................... 5
Hardware STORE Operation ....................................... 5
Hardware RECALL (Power-Up) .................................. 6
Software STORE ......................................................... 6
Software RECALL ....................................................... 6
Preventing AutoStore .................................................. 8
Data Protection ............................................................ 8
Maximum Ratings ............................................................. 9
Operating Range ............................................................... 9
DC Electrical Characteristics .......................................... 9
Data Retention and Endurance ..................................... 10
Capacitance .................................................................... 10
Thermal Resistance ........................................................ 10
AC Test Loads ................................................................ 11
AC Test Conditions ........................................................ 11
AC Switching Characteristics ....................................... 12
Switching Waveforms .................................................... 12
AutoStore/Power-Up RECALL ....................................... 15
Switching Waveforms .................................................... 15
Document Number: 001-45523 Rev. *O
Software Controlled STORE/RECALL Cycle ................ 16
Switching Waveforms .................................................... 16
Hardware STORE Cycle ................................................. 17
Switching Waveforms .................................................... 17
Truth Table For SRAM Operations ................................ 18
Ordering Information ...................................................... 19
Ordering Code Definitions ......................................... 19
Package Diagrams .......................................................... 20
Acronyms ........................................................................ 23
Document Conventions ................................................. 23
Units of Measure ....................................................... 23
Errata ............................................................................... 24
Part Numbers Affected .............................................. 24
8Mb (1024 K × 8, 512 K × 16) nvSRAM
Qualification Status ........................................................... 24
8Mb (1024 K × 8, 512 K × 16) nvSRAM
Errata Summary ............................................................... 24
Document History Page ................................................. 25
Sales, Solutions, and Legal Information ...................... 27
Worldwide Sales and Design Support ....................... 27
Products .................................................................... 27
PSoC® Solutions ...................................................... 27
Cypress Developer Community ................................. 27
Technical Support ..................................................... 27
Page 2 of 27
CY14B108L
CY14B108N
Pinouts
Figure 1. Pin Diagram – 48-ball FBGA
(× 8)
Top View
(not to scale)
(× 16)
Top View
(not to scale)
1
2
3
4
5
6
A
BLE
OE
A0
A1
A2
NC
A
NC
B
DQ8
BHE
A3
A4
CE
DQ0
B
NC
DQ4
C
DQ9 DQ10
A5
A6
DQ1
DQ2
C
A7
DQ5
VCC
D
VSS
A17
A7
DQ3
VCC
D
2
3
4
5
6
NC
OE
A0
A1
A2
NC
NC
NC
A3
A4
CE
DQ0
NC
A5
A6
VSS
DQ1
A17
1
DQ11
VCC
DQ2
VCAP
A16
DQ6
VSS
E
VCC DQ12
VCAP
A16
DQ4
VSS
E
DQ3
NC
A14
A15
NC
DQ7
F
DQ14 DQ13
A14
A15
DQ5
DQ6
F
NC
HSB
A12
A13
WE
NC
G
DQ15 HSB
A12
A13
WE
DQ7
G
A18
A8
A9
A10
A11
A19
H
A9
A10
A11
NC
H
A18
A8
Figure 2. Pin Diagram – 44/54-pin TSOP II
44-pin TSOP II
(× 8)
NC
[4]
NC
A0
A1
A2
A3
A4
CE
DQ0
DQ1
VCC
VSS
DQ2
DQ3
WE
A5
A6
A7
A8
A9
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Top View
(not to scale)
54-pin TSOP II
(× 16)
44
43
42
41
40
39
38
37
36
35
34
33
32
31
HSB
NC
A19
A18
A17
A16
A15
OE
DQ7
DQ6
VSS
VCC
DQ5
DQ4
30
29
28
27
26
25
24
23
VCAP
A14
A13
A12
A11
A10
NC
NC
NC
[4]
NC
A0
A1
A2
A3
A4
CE
DQ0
DQ1
DQ2
DQ3
VCC
VSS
DQ4
DQ5
DQ6
DQ7
WE
A5
A6
A7
A8
A9
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
Top View
(not to scale)
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
HSB
A18
A17
A16
A15
OE
BHE
BLE
DQ15
DQ14
DQ13
DQ12
VSS
VCC
DQ11
DQ10
DQ9
DQ8
VCAP
A14
A13
A12
A11
A10
NC
NC
NC
Note
4. Address expansion for 16-Mbit. NC pin not connected to die.
Document Number: 001-45523 Rev. *O
Page 3 of 27
CY14B108L
CY14B108N
Pin Definitions
Pin Name
I/O Type
A0–A19
Input
A0–A18
Description
Address inputs. Used to select one of the 1,048,576 bytes of the nvSRAM for × 8 configuration.
Address inputs. Used to select one of the 524,288 words of the nvSRAM for × 16 configuration.
DQ0–DQ7
Input/Output Bidirectional data I/O lines for × 8 configuration. Used as input or output lines depending on operation.
DQ0–DQ15
Bidirectional data I/O lines for × 16 configuration. Used as input or output lines depending on operation.
WE
Input
Write Enable input, Active LOW. When selected LOW, data on the I/O pins is written to the specific
address location.
CE
Input
Chip Enable input, Active LOW. When LOW, selects the chip. When HIGH, deselects the chip.
OE
Input
Output Enable, Active LOW. The active LOW OE input enables the data output buffers during read
cycles. I/O pins are tristated on deasserting OE HIGH.
BHE
Input
Byte High Enable, Active LOW. Controls DQ15–DQ8.
BLE
Input
Byte Low Enable, Active LOW. Controls DQ7–DQ0.
VSS
Ground
Ground for the device. Must be connected to the ground of the system.
VCC
Power supply Power supply inputs to the device.
HSB
Input/Output Hardware STORE Busy (HSB). When LOW this output indicates that a Hardware STORE is in progress.
When pulled LOW external to the chip it initiates a nonvolatile STORE operation. After each Hardware
and Software STORE operation, HSB is driven HIGH for a short time (tHHHD) with standard output high
current and then a weak internal pull-up resistor keeps this pin HIGH (external pull-up resistor
connection optional).
VCAP
Power supply AutoStore capacitor. Supplies power to the nvSRAM during power loss to store data from SRAM to
nonvolatile elements.
NC
No connect
No connect. This pin is not connected to the die.
Document Number: 001-45523 Rev. *O
Page 4 of 27
CY14B108L
CY14B108N
The CY14B108L/CY14B108N nvSRAM is made up of two
functional components paired in the same physical cell. They are
a SRAM memory cell and a nonvolatile QuantumTrap cell. The
SRAM memory cell operates as a standard fast static RAM. Data
in the SRAM is transferred to the nonvolatile cell (the STORE
operation), or from the nonvolatile cell to the SRAM (the RECALL
operation). Using this unique architecture, all cells are stored and
recalled in parallel. During the STORE and RECALL operations,
SRAM read and write operations are inhibited. The
CY14B108L/CY14B108N supports infinite reads and writes
similar to a typical SRAM. In addition, it provides infinite RECALL
operations from the nonvolatile cells and up to 1 million STORE
operations. See Truth Table For SRAM Operations on page 18
for a complete description of read and write modes.
SRAM Read
The CY14B108L/CY14B108N performs a read cycle when CE
and OE are LOW and WE and HSB are HIGH. The address
specified on pins A0–19 or A0–18 determines which of the
1,048,576 data bytes or 524,288 words of 16 bits each are
accessed. Byte enables (BHE, BLE) determine which bytes are
enabled to the output, in the case of 16-bit words. When the read
is initiated by an address transition, the outputs are valid after a
delay of tAA (read cycle 1). If the read is initiated by CE or OE,
the outputs are valid at tACE or at tDOE, whichever is later (read
cycle 2). The data output repeatedly responds to address
changes within the tAA access time without the need for
transitions on any control input pins. This remains valid until
another address change or until CE or OE is brought HIGH, or
WE or HSB is brought LOW.
AutoStore on page 8. In case AutoStore is enabled without a
capacitor on VCAP pin, the device attempts an AutoStore
operation without sufficient charge to complete the Store. This
corrupts the data stored in nvSRAM.
Figure 3 shows the proper connection of the storage capacitor
(VCAP) for automatic STORE operation. Refer to DC Electrical
Characteristics on page 9 for the size of VCAP. The voltage on
the VCAP pin is driven to VCC by a regulator on the chip. A pull-up
should be placed on WE to hold it inactive during power-up. This
pull-up is effective only if the WE signal is tristate during
power-up. Many MPUs tristate their controls on power-up. This
should be verified when using the pull-up. When the nvSRAM
comes out of power-on-RECALL, the MPU must be active or the
WE held inactive until the MPU comes out of reset.
To reduce unnecessary nonvolatile STOREs, AutoStore and
Hardware STORE operations are ignored unless at least one
write operation has taken place since the most recent STORE or
RECALL cycle. Software initiated STORE cycles are performed
regardless of whether a write operation has taken place. The
HSB signal is monitored by the system to detect if an AutoStore
cycle is in progress.
Figure 3. AutoStore Mode
VCC
0.1 uF
10 kOhm
Device Operation
VCC
SRAM Write
A write cycle is performed when CE and WE are LOW and HSB
is HIGH. The address inputs must be stable before entering the
write cycle and must remain stable until CE or WE goes HIGH at
the end of the cycle. The data on the common I/O pins DQ0–15
are written into the memory if the data is valid tSD before the end
of a WE controlled write or before the end of an CE controlled
write. The Byte Enable inputs (BHE, BLE) determine which bytes
are written, in the case of 16-bit words. Keep OE HIGH during
the entire write cycle to avoid data bus contention on common
I/O lines. If OE is left LOW, internal circuitry turns off the output
buffers tHZWE after WE goes LOW.
AutoStore Operation
The CY14B108L/CY14B108N stores data to the nvSRAM using
one of the following three storage operations: Hardware STORE
activated by the HSB; Software STORE activated by an address
sequence; AutoStore on device power-down. The AutoStore
operation is a unique feature of QuantumTrap technology and is
enabled by default on the CY14B108L/CY14B108N.
During a normal operation, the device draws current from VCC to
charge a capacitor connected to the VCAP pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the VCC pin drops below VSWITCH, the part
automatically disconnects the VCAP pin from VCC. A STORE
operation is initiated with power provided by the VCAP capacitor.
Note If the capacitor is not connected to VCAP pin, AutoStore
must be disabled using the soft sequence specified in Preventing
Document Number: 001-45523 Rev. *O
WE
VCAP
VSS
VCAP
Hardware STORE Operation
The CY14B108L/CY14B108N provides the HSB pin to control
and acknowledge the STORE operations. Use the HSB pin to
request a Hardware STORE cycle. When the HSB pin is driven
LOW, the CY14B108L/CY14B108N conditionally initiates a
STORE operation after tDELAY. An actual STORE cycle only
begins if a write to the SRAM has taken place since the last
STORE or RECALL cycle. The HSB pin also acts as an open
drain driver (internal 100 k weak pull-up resistor) that is internally driven LOW to indicate a busy condition when the STORE
(initiated by any means) is in progress.
Note After each Hardware and Software STORE operation HSB
is driven HIGH for a short time (tHHHD) with standard output high
current and then remains HIGH by internal 100 k pull-up
resistor.
Page 5 of 27
CY14B108L
CY14B108N
SRAM write operations that are in progress when HSB is driven
LOW by any means are given time (tDELAY) to complete before
the STORE operation is initiated. However, any SRAM write
cycles requested after HSB goes LOW are inhibited until HSB
returns HIGH. In case the write latch is not set, HSB is not driven
LOW by the CY14B108L/CY14B108N. But any SRAM read and
write cycles are inhibited until HSB is returned HIGH by MPU or
other external source.
During any STORE operation, regardless of how it is initiated,
the CY14B108L/CY14B108N continues to drive the HSB pin
LOW, releasing it only when the STORE is complete. Upon
completion of the STORE operation, the nvSRAM memory
access is inhibited for tLZHSB time after HSB pin returns HIGH.
Leave the HSB unconnected if it is not used.
Hardware RECALL (Power-Up)
During power-up or after any low power condition
(VCC< VSWITCH), an internal RECALL request is latched. When
VCC again exceeds the VSWITCH on power-up, a RECALL cycle
is automatically initiated and takes tHRECALL to complete. During
this time, the HSB pin is driven LOW by the HSB driver and all
reads and writes to nvSRAM are inhibited.
Software STORE
Data is transferred from the SRAM to the nonvolatile memory by
a software address sequence. The CY14B108L/CY14B108N
Software STORE cycle is initiated by executing sequential CE or
OE controlled read cycles from six specific address locations in
exact order. During the STORE cycle an erase of the previous
nonvolatile data is first performed, followed by a program of the
nonvolatile elements. After a STORE cycle is initiated, further
input and output are disabled until the cycle is completed.
Because a sequence of READs from specific addresses is used
for STORE initiation, it is important that no other read or write
accesses intervene in the sequence, or the sequence is aborted
and no STORE or RECALL takes place.
Document Number: 001-45523 Rev. *O
To initiate the Software STORE cycle, the following read
sequence must be performed.
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x8FC0 Initiate STORE cycle
The software sequence may be clocked with CE controlled reads
or OE controlled reads, with WE kept HIGH for all the six READ
sequences. After the sixth address in the sequence is entered,
the STORE cycle commences and the chip is disabled. HSB is
driven LOW. After the tSTORE cycle time is fulfilled, the SRAM is
activated again for the read and write operation.
Software RECALL
Data is transferred from the nonvolatile memory to the SRAM by
a software address sequence. A software RECALL cycle is
initiated with a sequence of read operations in a manner similar
to the software STORE initiation. To initiate the RECALL cycle,
the following sequence of CE or OE controlled read operations
must be performed.
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x4C63 Initiate RECALL cycle
Internally, RECALL is a two-step procedure. First, the SRAM
data is cleared; then, the nonvolatile information is transferred
into the SRAM cells. After the tRECALL cycle time, the SRAM is
again ready for read and write operations. The RECALL
operation does not alter the data in the nonvolatile elements.
Page 6 of 27
CY14B108L
CY14B108N
Table 1. Mode Selection
CE
WE
OE
BHE, BLE[5]
A15–A0[6]
Mode
I/O
Power
H
X
X
X
X
Not Selected
Output High Z
Standby
L
H
L
L
X
Read SRAM
Output data
Active
L
L
X
L
X
Write SRAM
Input data
Active
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8B45
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
AutoStore
Disable
Output data
Output data
Output data
Output data
Output data
Output data
Active[7]
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4B46
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
AutoStore
Enable
Output data
Output data
Output data
Output data
Output data
Output data
Active[7]
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8FC0
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Nonvolatile
STORE
Output data
Output data
Output data
Output data
Output data
Output High Z
Active ICC2[7]
L
H
L
X
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4C63
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Nonvolatile
RECALL
Output data
Output data
Output data
Output data
Output data
Output High Z
Active[7]
Errata: AutoStore Disable feature does not work in the device. For more information, see Errata on page 24.
Notes
5. BHE and BLE are applicable for × 16 configuration only.
6. While there are 20 address lines on the CY14B108L (19 address lines on the CY14B108N), only the 13 address lines (A14–A2) are used to control software modes.
Rest of the address lines are don’t care.
7. The six consecutive address locations must be in the order listed. WE must be HIGH during all six cycles to enable a nonvolatile cycle.
Document Number: 001-45523 Rev. *O
Page 7 of 27
CY14B108L
CY14B108N
Preventing AutoStore
The AutoStore function is disabled by initiating an AutoStore
disable sequence. A sequence of read operations is performed
in a manner similar to the Software STORE initiation. To initiate
the AutoStore disable sequence, the following sequence of CE
or OE controlled read operations must be performed:
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x8B45 AutoStore Disable
Note Errata: AutoStore Disable feature does not work in the
device. For more information, see Errata on page 24.
The AutoStore is re-enabled by initiating an AutoStore enable
sequence. A sequence of read operations is performed in a
manner similar to the Software RECALL initiation. To initiate the
Document Number: 001-45523 Rev. *O
AutoStore enable sequence, the following sequence of CE or OE
controlled read operations must be performed:
1. Read address 0x4E38 Valid READ
2. Read address 0xB1C7 Valid READ
3. Read address 0x83E0 Valid READ
4. Read address 0x7C1F Valid READ
5. Read address 0x703F Valid READ
6. Read address 0x4B46 AutoStore Enable
If the AutoStore function is disabled or re-enabled, a manual
STORE operation (Hardware or Software) must be issued to
save the AutoStore state through subsequent power-down
cycles. The part comes from the factory with AutoStore enabled
and 0x00 written in all cells.
Data Protection
The CY14B108L/CY14B108N protects data from corruption
during low voltage conditions by inhibiting all externally initiated
STORE and write operations. The low voltage condition is
detected when VCC < VSWITCH. If the CY14B108L/CY14B108N
is in a write mode (both CE and WE are LOW) at power-up, after
a RECALL or STORE, the write is inhibited until the SRAM is
enabled after tLZHSB (HSB to output active). This protects against
inadvertent writes during power-up or brown out conditions.
Page 8 of 27
CY14B108L
CY14B108N
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................ –65 C to +150 C
Maximum accumulated storage time
Transient voltage (< 20 ns) on
any pin to ground potential ................. –2.0 V to VCC + 2.0 V
Package power dissipation
capability (TA = 25 °C) ................................................. 1.0 W
Surface mount Pb soldering
temperature (3 Seconds) ......................................... +260 C
At 150 C ambient temperature ...................... 1000 h
DC output current (1 output at a time, 1s duration) .... 15 mA
At 85 C ambient temperature ..................... 20 Years
Static discharge voltage
(per MIL-STD-883, Method 3015) .......................... > 2001 V
Maximum junction temperature .................................. 150 C
Supply voltage on VCC relative to VSS ...........–0.5 V to 4.1 V
Voltage applied to outputs
in High Z state .................................... –0.5 V to VCC + 0.5 V
Input voltage ........................................–0.5 V to Vcc + 0.5 V
Latch up current .................................................... > 200 mA
Operating Range
Range
Ambient Temperature
VCC
–40 C to +85 C
2.7 V to 3.6 V
Industrial
DC Electrical Characteristics
Over the Operating Range
Parameter
Description
Test Conditions
Min
Typ [8]
Max
Unit
2.7
3.0
3.6
V
VCC
Power supply
ICC1
Average VCC current
tRC = 20 ns
tRC = 25 ns
tRC = 45 ns
Values obtained without output loads
(IOUT = 0 mA)
–
–
75
75
57
mA
mA
mA
ICC2
Average VCC current during
STORE
All inputs don’t care, VCC = Max
Average current for duration tSTORE
–
–
20
mA
ICC3
Average VCC current at
tRC= 200 ns, VCC(Typ), 25 °C
All inputs cycling at CMOS levels.
Values obtained without output loads
(IOUT = 0 mA).
–
40
–
mA
ICC4
Average VCAP current during
AutoStore cycle
All inputs don’t care. Average current
for duration tSTORE
–
–
10
mA
ISB
VCC standby current
CE > (VCC – 0.2 V).
VIN < 0.2 V or > (VCC – 0.2 V).
Standby current level after
nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
–
–
10
mA
IIX[9]
Input leakage current (except
HSB)
VCC = Max, VSS < VIN < VCC
–2
–
+2
A
Input leakage current (for HSB)
VCC = Max, VSS < VIN < VCC
–200
–
+2
A
IOZ
Off-state output leakage current VCC = Max, VSS < VOUT < VCC,
CE or OE > VIH or
BHE/BLE > VIH or WE < VIL
–2
–
+2
A
VIH
Input HIGH voltage
2.0
–
VCC + 0.5
V
VIL
Input LOW voltage
Vss – 0.5
–
0.8
V
VOH
Output HIGH voltage
IOUT = –2 mA
2.4
–
–
V
VOL
Output LOW voltage
IOUT = 4 mA
–
–
0.4
V
Notes
8. Typical values are at 25 °C, VCC = VCC(Typ). Not 100% tested.
9. The HSB pin has IOUT = –2 µA for VOH of 2.4 V when both active HIGH and LOW drivers are disabled. When they are enabled standard VOH and VOL are valid. This
parameter is characterized but not tested.
Document Number: 001-45523 Rev. *O
Page 9 of 27
CY14B108L
CY14B108N
DC Electrical Characteristics (continued)
Over the Operating Range
Parameter
Description
VCAP[10]
VVCAP[11, 12]
Storage capacitor
Test Conditions
Min
Typ [8]
Between VCAP pin and VSS
122
–
Maximum voltage driven on VCAP VCC = Max
pin by the device
Max
Unit
150
360
F
–
VCC
V
Data Retention and Endurance
Over the Operating Range
Parameter
Description
DATAR
Data retention
NVC
Nonvolatile STORE operations
Min
Unit
20
Years
1,000
K
Max
Unit
Capacitance
Parameter [12]
Description
CIN
Input capacitance
COUT
Output capacitance
Test Conditions
TA = 25 C, f = 1 MHz, VCC = VCC(Typ)
14
pF
14
pF
Thermal Resistance
Parameter [12]
Description
JA
Thermal resistance
(Junction to ambient)
JC
Thermal resistance
(Junction to case)
Test Conditions
Test
conditions
follow
standard test methods and
procedures for measuring
thermal
impedance,
in
accordance
with
EIA/JESD51.
48-ball FBGA 44-pin TSOP II 54-pin TSOP II Unit
42.2
45.3
44.22
C/W
6.3
5.2
8.26
C/W
Notes
10. Min VCAP value guarantees that there is a sufficient charge available to complete a successful AutoStore operation. Max VCAP value guarantees that the capacitor on
VCAP is charged to a minimum voltage during a Power-Up RECALL cycle so that an immediate power-down cycle can complete a successful AutoStore. Therefore it
is always recommended to use a capacitor within the specified min and max limits. Refer application note AN43593 for more details on VCAP options.
11. Maximum voltage on VCAP pin (VVCAP) is provided for guidance when choosing the VCAP capacitor. The voltage rating of the VCAP capacitor across the operating
temperature range should be higher than the VVCAP voltage.
12. These parameters are guaranteed by design and are not tested.
Document Number: 001-45523 Rev. *O
Page 10 of 27
CY14B108L
CY14B108N
AC Test Loads
Figure 4. AC Test Loads
577 
3.0 V
577 
3.0 V
R1
for tristate specs
R1
OUTPUT
OUTPUT
30 pF
R2
789 
5 pF
R2
789 
AC Test Conditions
Input pulse levels .................................................. 0 V to 3 V
Input rise and fall times (10%–90%) ........................... < 3 ns
Input and output timing reference levels ...................... 1.5 V
Document Number: 001-45523 Rev. *O
Page 11 of 27
CY14B108L
CY14B108N
AC Switching Characteristics
Over the Operating Range
Parameters [13]
Cypress
Alt Parameter
Parameter
SRAM Read Cycle
tACE
tACS
tRC
tRC[14]
tAA[15]
tAA
tOE
tDOE
tOH
tOHA[15]
tLZCE[16, 17]
tLZ
tHZ
tHZCE[16, 17]
tOLZ
tLZOE[16, 17]
[16,
17]
tHZOE
tOHZ
tPA
tPU[16]
tPS
tPD[16]
tDBE
–
–
tLZBE[16]
–
tHZBE[16]
SRAM Write Cycle
tWC
tWC
tWP
tPWE
tSCE
tCW
tDW
tSD
tDH
tHD
tAW
tAW
tAS
tSA
tWR
tHA
tHZWE[16, 17, 18] tWZ
tOW
tLZWE[16, 17]
–
tBW
20 ns
Description
25 ns
45 ns
Unit
Min
Max
Min
Max
Min
Max
Chip enable access time
Read cycle time
Address access time
Output enable to data valid
Output hold after address change
Chip enable to output active
Chip disable to output inactive
Output enable to output active
Output disable to output inactive
Chip enable to power active
Chip disable to power standby
Byte enable to data valid
Byte enable to output active
Byte disable to output inactive
–
20
–
–
3
3
–
0
–
0
–
–
0
–
20
–
20
10
–
–
8
–
8
–
20
10
–
8
–
25
–
–
3
3
–
0
–
0
–
–
0
–
25
–
25
12
–
–
10
–
10
–
25
12
–
10
–
45
–
–
3
3
–
0
–
0
–
–
0
–
45
–
45
20
–
–
15
–
15
–
45
20
–
15
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Write cycle time
Write pulse width
Chip enable to end of write
Data setup to end of write
Data hold after end of write
Address setup to end of write
Address setup to start of write
Address hold after end of write
Write enable to output disable
Output active after end of write
Byte enable to end of write
20
15
15
8
0
15
0
0
–
3
15
–
–
–
–
–
–
–
–
8
–
–
25
20
20
10
0
20
0
0
–
–
–
–
–
–
–
–
10
–
–
45
30
30
15
0
30
0
0
–
3
30
–
–
–
–
–
–
–
–
15
–
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
3
20
Switching Waveforms
Figure 5. SRAM Read Cycle #1 (Address Controlled) [14, 15, 19]
tRC
Address
Address Valid
tAA
Data Output
Previous Data Valid
Output Data Valid
tOHA
Notes
13. Test conditions assume signal transition time of 3 ns or less, timing reference levels of VCC/2, input pulse levels of 0 to VCC(typ), and output loading of the specified
IOL/IOH and load capacitance shown in Figure 4 on page 11.
14. WE must be HIGH during SRAM read cycles.
15. Device is continuously selected with CE, OE and BHE / BLE LOW.
16. These parameters are guaranteed by design but not tested.
17. Measured ±200 mV from steady state output voltage.
18. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
19. HSB must remain HIGH during READ and WRITE cycles.
Document Number: 001-45523 Rev. *O
Page 12 of 27
CY14B108L
CY14B108N
Switching Waveforms (continued)
Figure 6. SRAM Read Cycle #2 (CE and OE Controlled) [20, 21, 22]
Address
Address Valid
tRC
tHZCE
tACE
CE
tAA
tLZCE
tHZOE
tDOE
OE
tHZBE
tLZOE
tDBE
BHE, BLE
tLZBE
Data Output
High Impedance
Output Data Valid
tPU
ICC
tPD
Active
Standby
Figure 7. SRAM Write Cycle #1 (WE Controlled) [20, 22, 23, 24]
tWC
Address
Address Valid
tSCE
tHA
CE
tBW
BHE, BLE
tAW
tPWE
WE
tSA
tSD
Data Input
Input Data Valid
tHZWE
Data Output
tHD
Previous Data
tLZWE
High Impedance
Notes
20. BHE and BLE are applicable for × 16 configuration only.
21. WE must be HIGH during SRAM read cycles.
22. HSB must remain HIGH during READ and WRITE cycles.
23. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
24. CE or WE must be >VIH during address transitions.
Document Number: 001-45523 Rev. *O
Page 13 of 27
CY14B108L
CY14B108N
Switching Waveforms (continued)
Figure 8. SRAM Write Cycle #2 (CE Controlled) [25, 26, 27, 28]
tWC
Address Valid
Address
tSA
tSCE
tHA
CE
tBW
BHE, BLE
tPWE
WE
tHD
tSD
Input Data Valid
Data Input
High Impedance
Data Output
Figure 9. SRAM Write Cycle #3 (BHE and BLE Controlled) [25, 26, 27, 28]
tWC
Address
Address Valid
tSCE
CE
tSA
tHA
tBW
BHE, BLE
tAW
tPWE
WE
tSD
Data Input
tHD
Input Data Valid
High Impedance
Data Output
Notes
25. BHE and BLE are applicable for × 16 configuration only.
26. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state.
27. HSB must remain HIGH during READ and WRITE cycles.
28. CE or WE must be >VIH during address transitions.
Document Number: 001-45523 Rev. *O
Page 14 of 27
CY14B108L
CY14B108N
AutoStore/Power-Up RECALL
Over the Operating Range
Parameter
20 ns
Description
25 ns
45 ns
Min
Max
Min
Max
Min
Max
Unit
tHRECALL[29]
Power-Up RECALL duration
–
20
–
20
–
20
ms
tSTORE [30]
STORE cycle duration
–
8
–
8
–
8
ms
Time allowed to complete SRAM
write cycle
–
20
–
25
–
25
ns
tDELAY
[31]
VSWITCH
Low voltage trigger level
tVCCRISE[32]
VCC rise time
–
2.65
–
2.65
–
2.65
V
150
–
150
–
150
–
s
VHDIS[32]
tLZHSB[32]
HSB output disable voltage
–
1.9
–
1.9
–
1.9
V
HSB to output active time
–
5
–
5
–
5
s
tHHHD[32]
HSB high active time
–
500
–
500
–
500
ns
Switching Waveforms
Figure 10. AutoStore or Power-Up RECALL [33]
VCC
VSWITCH
VHDIS
t VCCRISE
30
tHHHD
Note
Note30
tSTORE
tHHHD
Note 34
tSTORE
34
Note
HSB OUT
tDELAY
tLZHSB
AutoStore
tLZHSB
tDELAY
POWERUP
RECALL
tHRECALL
tHRECALL
Read & Write
Inhibited
(RWI)
POWER-UP
RECALL
Read & Write
BROWN
OUT
AutoStore
POWER-UP
RECALL
Read & Write
POWER
DOWN
AutoStore
Notes
29. tHRECALL starts from the time VCC rises above VSWITCH.
30. If an SRAM write has not taken place since the last nonvolatile cycle, no AutoStore or Hardware STORE takes place.
31. On a Hardware STORE and AutoStore initiation, SRAM write operation continues to be enabled for time tDELAY.
32. These parameters are guaranteed by design but not tested.
33. Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH.
34. During power-up and power-down, HSB glitches when HSB pin is pulled up through an external resistor.
Document Number: 001-45523 Rev. *O
Page 15 of 27
CY14B108L
CY14B108N
Software Controlled STORE/RECALL Cycle
Over the Operating Range
Parameter [35, 36]
tRC
tSA
tCW
tHA
tRECALL
Description
Min
20
0
15
0
–
STORE/RECALL initiation cycle time
Address setup time
Clock pulse width
Address hold time
RECALL duration
20 ns
Max
–
–
–
–
200
Min
25
0
20
0
–
25 ns
Max
–
–
–
–
200
Min
45
0
30
0
–
45 ns
Max
–
–
–
–
200
Unit
ns
ns
ns
ns
s
Switching Waveforms
Figure 11. CE and OE Controlled Software STORE/RECALL Cycle [36]
tRC
Address
tRC
Address #1
tSA
Address #6
tCW
tCW
CE
tHA
tSA
tHA
tHA
tHA
OE
tHHHD
HSB (STORE only)
tHZCE
tLZCE
t DELAY
37
Note
tLZHSB
High Impedance
tSTORE/tRECALL
DQ (DATA)
RWI
Figure 12. Autostore Enable/Disable Cycle [36]
Address
tRC
tRC
Address #1
Address #6
tSA
CE
tCW
tCW
tHA
tSA
tHA
tHA
tHA
OE
tLZCE
tHZCE
tSS
37
Note
t DELAY
DQ (DATA)
RWI
Notes
35. The software sequence is clocked with CE controlled or OE controlled reads.
36. The six consecutive addresses must be read in the order listed in Table 1 on page 7. WE must be HIGH during all six consecutive cycles.
37. DQ output data at the sixth read may be invalid since the output is disabled at tDELAY time.
Document Number: 001-45523 Rev. *O
Page 16 of 27
CY14B108L
CY14B108N
Hardware STORE Cycle
Over the Operating Range
Parameter
20 ns
Description
25 ns
45 ns
Min
Max
Min
Max
Min
Max
Unit
tDHSB
HSB to output active time when
write latch not set
–
20
–
25
–
25
ns
tPHSB
Hardware STORE pulse width
15
–
15
–
15
–
ns
Soft sequence processing time
–
100
–
100
–
100
s
tSS
[38, 39]
Switching Waveforms
Figure 13. Hardware STORE Cycle [40]
Write latch set
tPHSB
HSB (IN)
tSTORE
tHHHD
tDELAY
HSB (OUT)
tLZHSB
DQ (Data Out)
RWI
Write latch not set
tPHSB
HSB pin is driven high to VCC only by Internal
100 kOhm resistor,
HSB driver is disabled
SRAM is disabled as long as HSB (IN) is driven low.
HSB (IN)
HSB (OUT)
tDELAY
tDHSB
tDHSB
RWI
Figure 14. Soft Sequence Processing [38, 39]
Soft Sequence
Command
Address
Address #1
tSA
Address #6
tCW
tSS
Soft Sequence
Command
Address #1
tSS
Address #6
tCW
CE
VCC
Notes
38. This is the amount of time it takes to take action on a soft sequence command. Vcc power must remain HIGH to effectively register command.
39. Commands such as STORE and RECALL lock out I/O until operation is complete which further increases this time. See the specific command.
40. If an SRAM write has not taken place since the last nonvolatile cycle, no AutoStore or Hardware STORE takes place.
Document Number: 001-45523 Rev. *O
Page 17 of 27
CY14B108L
CY14B108N
Truth Table For SRAM Operations
HSB should remain HIGH for SRAM Operations.
Table 2. Truth Table for × 8 Configuration
CE
Inputs/Outputs[41]
WE
OE
Mode
Power
H
X
X
High Z
Deselect/Power-down
Standby
L
H
L
Data out (DQ0–DQ7);
Read
Active
L
H
H
High Z
Output disabled
Active
L
L
X
Data in (DQ0–DQ7);
Write
Active
Table 3. Truth Table for × 16 Configuration
BHE[42]
BLE[42]
Inputs/Outputs[41]
CE
WE
OE
Mode
Power
H
X
X
X
X
High Z
Deselect/Power-down
Standby
L
X
X
H
H
High Z
Output disabled
Active
L
H
L
L
L
Data out (DQ0–DQ15)
Read
Active
L
H
L
H
L
Data out (DQ0–DQ7);
DQ8–DQ15 in High Z
Read
Active
L
H
L
L
H
Data out (DQ8–DQ15);
DQ0–DQ7 in High Z
Read
Active
L
H
H
L
L
High Z
Output disabled
Active
L
H
H
H
L
High Z
Output disabled
Active
L
H
H
L
H
High Z
Output disabled
Active
L
L
X
L
L
Data in (DQ0–DQ15)
Write
Active
L
L
X
H
L
Data in (DQ0–DQ7);
DQ8–DQ15 in High Z
Write
Active
L
L
X
L
H
Data in (DQ8–DQ15);
DQ0–DQ7 in High Z
Write
Active
Notes
41. Data DQ0–DQ7 for × 8 configuration and Data DQ0–DQ15 for × 16 configuration.
42. BHE and BLE are applicable for × 16 configuration only.
Document Number: 001-45523 Rev. *O
Page 18 of 27
CY14B108L
CY14B108N
Ordering Information
Speed
(ns)
20
25
45
Ordering Code
Package Diagram
Package Type
CY14B108L-ZS20XIT
51-85087
44-pin TSOP II
CY14B108L-ZS20XI
51-85087
44-pin TSOP II
CY14B108L-ZS25XIT
51-85087
44-pin TSOP II
CY14B108L-ZS25XI
51-85087
44-pin TSOP II
CY14B108L-BA25XIT
51-85128
48-ball FBGA
CY14B108L-BA25XI
51-85128
48-ball FBGA
CY14B108N-BA25XIT
51-85128
48-ball FBGA
CY14B108N-BA25XI
51-85128
48-ball FBGA
CY14B108N-ZSP25XIT
51-85160
54-pin TSOP II
CY14B108N-ZSP25XI
51-85160
54-pin TSOP II
CY14B108L-ZS45XIT
51-85087
44-pin TSOP II
CY14B108L-ZS45XI
51-85087
44-pin TSOP II
CY14B108L-BA45XIT
51-85128
48-ball FBGA
CY14B108L-BA45XI
51-85128
48-ball FBGA
CY14B108N-BA45XIT
51-85128
48-ball FBGA
CY14B108N-BA45XI
51-85128
48-ball FBGA
CY14B108N-ZSP45XIT
51-85160
54-pin TSOP II
CY14B108N-ZSP45XI
51-85160
54-pin TSOP II
Operating Range
Industrial
All the above parts are Pb-free.
Ordering Code Definitions
CY 14 B 108 L - ZS 20 X I T
Option:
T - Tape & Reel
Blank - Std.
Pb-Free
Package:
ZS - 44-pin TSOP II
BA - 48-ball FBGA
ZSP - 54-pin TSOP II
Voltage:
B - 3.0 V
Temperature:
I - Industrial (–40 to 85 °C)
Data Bus:
L-×8
N - × 16
Speed:
20 - 20 ns
25 - 25 ns
45 - 45 ns
Density:
108 - 8 Mb
14 - NVSRAM
Cypress
Document Number: 001-45523 Rev. *O
Page 19 of 27
CY14B108L
CY14B108N
Package Diagrams
Figure 15. 44-pin TSOP II Package Outline, 51-85087
51-85087 *E
Document Number: 001-45523 Rev. *O
Page 20 of 27
CY14B108L
CY14B108N
Package Diagrams (continued)
Figure 16. 48-ball FBGA (6 × 10 × 1.2 mm) Package Outline, 51-85128
51-85128 *G
Document Number: 001-45523 Rev. *O
Page 21 of 27
CY14B108L
CY14B108N
Package Diagrams (continued)
Figure 17. 54-pin TSOP II (22.4 × 11.84 × 1.0 mm) Package Outline, 51-85160
51-85160 *E
Document Number: 001-45523 Rev. *O
Page 22 of 27
CY14B108L
CY14B108N
Acronyms
Acronym
Document Conventions
Description
Units of Measure
CMOS
complementary metal oxide semiconductor
BHE
byte high enable
°C
degree Celsius
BLE
byte low enable
k
kilohm
CE
EIA
chip enable
kHz
kilohertz
electronic industries alliance
MHz
megahertz
FBGA
fine-pitch ball grid array
A
microampere
HSB
I/O
hardware store busy
F
microfarad
input/output
s
microsecond
nvSRAM
non-volatile static random access memory
mA
milliampere
OE
RoHS
output enable
ms
millisecond
restriction of hazardous substances
ns
nanosecond
RWI
read and write inhibited

ohm
SRAM
static random access memory
%
percent
TSOP
thin small outline package
pF
picofarad
WE
write enable
s
second
V
volt
W
watt
Document Number: 001-45523 Rev. *O
Symbol
Unit of Measure
Page 23 of 27
CY14B108L
CY14B108N
Errata
This section describes the errata for the 8 Mb (2048 K × 8 and 1024 K × 16) nvSRAM product families. Details include errata trigger
conditions, scope of impact, available workarounds, and silicon revision applicability.
Contact your local Cypress Sales Representative if you have questions. You can also send your related queries directly to
[email protected]
Part Numbers Affected
Part Number
Device Characteristics
CY14B108L
1024 K × 8, Asynchronous Interface nvSRAM in 44 TSOP-II and 48 FBGA package options
CY14B108N
512 K × 16, Asynchronous Interface nvSRAM in 54 TSOP-II and 48 FBGA package options
8Mb (1024 K × 8, 512 K × 16) nvSRAM Qualification Status
Production parts.
8Mb (1024 K × 8, 512 K × 16) nvSRAM Errata Summary
The following table defines the errata applicability to available CY14B108L, CY14B108N devices.
Items
Part Number
Silicon Revision
Fix Status
1. AutoStore Disable feature does not work correctly
CY14B108L
CY14B108N
Rev 0
None.
This issue is applicable
to all 8Mb nvSRAM parts
in production
1. AutoStore Disable feature does not work correctly
■
Problem Definition
The AutoStore Disable soft sequence disables the AutoStore feature in nvSRAMs. The AutoStore Disable feature is used in
applications where data written in the SRAM is not required to be saved automatically on power loss. The 8Mb nvSRAM executes
the nonvolatile Store automatically in half the memory (4Mb) even after the AutoStore feature is disabled. The reason is as follows:
The 8Mb nvSRAM uses two dice stack of 4Mb with HSB pin of each die are tied together. Each nvSRAM die in the stacked-die
monitors the VCC power independently. When the device VCC fails, the die which detects the VCC dropping below VSWITCH first,
internally triggers the power down interrupt and drives its HSB output low. Since the HSB is a bidirectional pin, the low HSB output
driven by one die is detected as HSB input by the other die. Therefore, low on the HSB input of other die internally triggers hardware
Store and executes unintended nonvolatile Store even though AutoStore was disabled by AutoStore Disable soft sequence.
■
Parameters Affected
None.
■
Trigger Condition(S)
Device VCC power down with nvSRAM AutoStore disable.
■
Scope of Impact
It can corrupt the data in half of the memory by overwriting the existing data in its nonvolatile memory with unintended data.
■
Workaround
None. AutoStore disable feature should not be used in 8Mb nvSRAMs.
■
Fix Status
This issue is applicable to all 8Mb nvSRAM parts in production and will continue serving with errata. There is no plan to fix this
issue in the existing parts in production.
Document Number: 001-45523 Rev. *O
Page 24 of 27
CY14B108L
CY14B108N
Document History Page
Document Title: CY14B108L/CY14B108N, 8-Mbit (1024 K × 8/512 K × 16) nvSRAM
Document Number: 001-45523
Revision
ECN
Orig. of
Change
Submission
Date
**
2428826
GVCH
See ECN
New Data Sheet
*A
2520023
GVCH /
PYRS
06/23/08
Updated ICC1 for tRC=20ns, 25ns and 45ns access speed for both industrial
and Commercial temperature Grade
Updated Thermal resistance values for 48-FBGA,44-TSOP II and 54-TSOP II
packages
Changed tCW value from 16ns to 15ns
*B
2676670
GVCH /
PYRS
03/20/2009
Added maximum accumulated storage time for 150C and 85C Temperature
Added best practices
Changed ICC2 from 12mA to 20mA
Changed ICC3 from 38mA to 40mA
Changed ICC4 from 12mA to 10mA
Changed ISB from 6mA to 10mA
Changed VCAP from 164uF to 360uF
Changed Input Rise and Fall Times from 5ns to 3ns
Updated ICC1, ICC3, ISBand IOZ Test conditions
Changed tDELAY to 20ns, 25ns, 25ns for 15ns, 20ns, 45ns part respectively
Changed tSTORE from 15ms to 8ms
Added VHDIS, tHHHD and tLZHSB parameters
Software controlled STORE/RECALL cycle table: Changed tAS to tSA
Changed tGHAX to tHA
Added tDHSB parameter
Changed tHLHX to tPHSB
Updated tSS from 70us to 100us
Added Truth table for SRAM operations
Updated ordering information
*C
2712462
GVCH /
PYRS
05/29/2009
Moved data sheet status from Preliminary to Final
Updated AutoStore operation
Updated ISB test condition
Updated footnote 7
Referenced footnote 9 to VCCRISE, tHHHD and tLZHSB parameters
Updated VHDIS parameter description
*D
2746310
GVCH
07/29/2009
Page 4: Updated Hardware STORE (HSB) operation description
page 5: Updated Software STORE description
Updated tDELAY parameter description
Updated footnote 18 and added footnote 23
Referenced footnote 23 to Figure 11 and Figure 12
*E
2759948
GVCH
09/04/2009
Removed commercial temperature related specs
*F
2828257
GVCH
12/15/2009
Changed STORE cycles to QuantumTrap from 200K to 1 Million
Added Contents on page 2
*G
2894560
GVCH
03/18/2010
Removed part numbers CY14B108N-ZSP20XIT and CY14B108N-ZSP20XI
from ordering information table.
Updated Package diagrams 51-85160 and 51-85087.
Updated Sales, Solution, and Legal Information Section.
Updated copyright section.
Updated table of contents.
*H
2923475
GVCH /
AESA
04/27/2010
Table 1: Added more clarity on HSB pin operation
Hardware STORE Operation: Added more clarity on HSB pin operation
Table 1: Added more clarity on BHE/BLE pin operation
Updated HSB pin operation in Figure 10
Updated footnote 34
Document Number: 001-45523 Rev. *O
Description of Change
Page 25 of 27
CY14B108L
CY14B108N
Document History Page (continued)
Document Title: CY14B108L/CY14B108N, 8-Mbit (1024 K × 8/512 K × 16) nvSRAM
Document Number: 001-45523
Revision
ECN
Orig. of
Change
Submission
Date
*I
3143765
GVCH
01/17/2011
48-ball FBGA package: 16 Mb address expansion is not supported
Updated thermal resistance values for all packages
Added Acronyms table and Document Conventions table
*J
3311413
GVCH
07/13/2011
Updated DC Electrical Characteristics (Added Note 9 and referred the same
note in VCAP parameter).
Updated AC Switching Characteristics (Added Note 13 and referred the same
note in Parameters).
Updated Package Diagrams.
Description of Change
*K
3580269
GVCH
04/12/2012
Updated Package Diagrams.
*L
3658005
GVCH
08/10/2012
Updated Maximum Ratings (Changed “Ambient temperature with power
applied” to “Maximum junction temperature”).
Updated DC Electrical Characteristics (Added VVCAP parameter and its details,
added Note 11 and referred the same note in VVCAP parameter, also referred
Note 12 in VVCAP parameter).
Updated Package Diagrams (spec 51-85160 (Changed revision from *C to *D)).
*M
4500772
ZSK
09/12/2014
Updated Package Diagrams:
spec 51-85087 – Changed revision from *D to *E.
spec 51-85160 – Changed revision from *D to *E.
Added Errata.
Updated to new template.
*N
4563189
ZSK
11/12/2014
Added related documentation hyperlink in page 1
*O
4714292
GVCH
04/08/2015
No technical updates.
Completing Sunset Review.
Document Number: 001-45523 Rev. *O
Page 26 of 27
CY14B108L
CY14B108N
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
cypress.com/go/automotive
cypress.com/go/clocks
cypress.com/go/interface
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/psoc
psoc.cypress.com/solutions
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Community | Forums | Blogs | Video | Training
Technical Support
cypress.com/go/support
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2008-2015. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-45523 Rev. *O
Revised April 8, 2015
All products and company names mentioned in this document may be the trademarks of their respective holders.
Page 27 of 27