Download DataSheet_CY8C24x93.pdf

CY8C24X93
PSoC® Programmable System-on-Chip
PSoC® Programmable System-on-Chip
Features
■
Powerful Harvard-architecture processor
❐ M8C CPU with a max speed of 24 MHz
■
Operating Range: 1.71 V to 5.5 V
❐ Standby Mode 1.1 μA (Typ)
❐ Deep Sleep 0.1 μA (Typ)
■
Operating Temperature range: –40 °C to +85 °C
■
Flexible on-chip memory
❐ 8 KB flash, 1 KB SRAM
❐ 16 KB flash, 2 KB SRAM
❐ 32 KB flash, 2 KB SRAM
❐ Read while Write with EEPROM emulation
❐ 50,000 flash erase/write cycles
❐ In-system programming simplifies manufacturing process
■
Four Clock Sources
❐ Internal main oscillator (IMO): 6/12/24 MHz
❐ Internal low-speed oscillator (ILO) at 32 kHz for watchdog
and sleep timers
❐ External 32 KHz Crystal Oscillator
❐ External Clock Input
■
Programmable pin configurations
❐ Up to 36 general purpose dual mode GPIO (Analog inputs
and Digital I/O supported)
❐ High sink current of 25 mA per GPIO
• Max sink current 120 mA for all GPIOs
❐ Source Current
• 5 mA on ports 0 and 1
• 1 mA on ports 2,3 and 4
❐ Configurable internal pull-up, high-Z and open drain modes
❐ Selectable, regulated digital I/O on port 1
❐ Configurable input threshold on port 1
Cypress Semiconductor Corporation
Document Number: 001-86894 Rev. *A
•
■
Versatile Analog functions
❐ Internal Low-Dropout voltage regulator for high power supply
rejection ratio (PSRR)
■
Full-Speed USB
❐ 12 Mbps USB 2.0 compliant
❐ Eight unidirectional endpoints
❐ One bidirectional endpoint
❐ Dedicated 512 byte SRAM
❐ No external crystal required
■
Additional system resources
❐ I2C Slave:
• Selectable to 50 kHz, 100 kHz, or 400 kHz
❐ Configurable up to 12 MHz SPI master and slave
❐ Three 16-bit timers
❐ Watchdog and sleep timers
❐ Integrated supervisory circuit
❐ 10-bit incremental analog-to-digital converter (ADC) with
internal voltage reference
❐ Two general-purpose Comparators
• 3 Voltage References (0.8 V, 1 V, 1.2 V)
• Any pin to either comparator inputs
• Low-power operation at 10 µA
❐ One 8-bit IDAC with full scale range of 512 µA
❐ One 8-bit Software PWM
■
Development Platform
❐ PSoC Designer™ IDE
■
GPIOs and Package options
❐ 13 GPIOs - QFN 16
❐ 28 GPIOs - QFN 32
❐ 34 GPIOs - QFN 48
❐ 36 GPIOs - QFN 48
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 30, 2013
CY8C24X93
Logic Block Diagram
Port 4
Port 3
Port 2
Port 1
Port 0
1.8/2.5/3V
LDO
PWRSYS [1]
(Regulator)
PSoC CORE
SYSTEM BUS
Global Analog Interconnect
1K/2K
SRAM
Supervisory ROM (SROM)
Interrupt
Controller
8K/16K/32K Flash
Nonvolatile Memory
Sleep and
Watchdog
CPU Core (M8C)
6/12/24 MHz Internal Main Oscillator
(IMO)
Internal Low Speed Oscillator (ILO)
Multiple Clock Sources
ANALOG
SYSTEM
Analog
Reference
ADC
Two
Comparators
Analog Mux
IDAC
SYSTEM BUS
USB
I2C
Slave
Internal
Voltage
References
System
Resets
POR
and
LVD
SPI
Master/
Slave
Three 16-Bit
Programmable
Timers
Digital
Clocks
SYSTEM RESOURCES
Note
1. Internal voltage regulator for internal circuitry.
Document Number: 001-86894 Rev. *A
Page 2 of 54
CY8C24X93
Contents
PSoC® Functional Overview ................................................. 4
PSoC Core ....................................................................... 4
Analog system ................................................................. 4
Additional System Resources .......................................... 5
Getting Started ....................................................................... 6
Silicon Errata .................................................................... 6
Development Kits ............................................................. 6
Training ............................................................................ 6
CYPros Consultants ......................................................... 6
Solutions Library .............................................................. 6
Technical Support ............................................................ 6
Development Tools ............................................................... 7
PSoC Designer Software Subsystems ............................ 7
Designing with PSoC Designer ............................................ 8
Select User Modules ........................................................ 8
Configure User Modules .................................................. 8
Organize and Connect ..................................................... 8
Generate, Verify, and Debug ........................................... 8
Pinouts ................................................................................... 9
16-pin QFN (13 GPIOs) [2] .............................................. 9
32-pin QFN (28 GPIOs) [6] ............................................ 10
32-pin QFN (28 GPIOs) [10] .......................................... 11
48-pin QFN (34 GPIOs) [14] .......................................... 12
48-pin QFN (36 GPIOs (With USB)) [19] ....................... 13
48-pin QFN (OCD) (36 GPIOs) [23] ............................... 14
Electrical Specifications (CY8C24193/493) ....................... 15
Absolute Maximum Ratings (CY8C24193/493) ............. 15
Operating Temperature (CY8C24193/493) .................... 15
DC Chip-Level Specifications (CY8C24193/493) .......... 16
DC GPIO Specifications (CY8C24193/493) ................... 17
DC Analog Mux Bus Specifications
(CY8C24193/493) .................................................................. 20
DC Low Power Comparator Specifications
(CY8C24193/493) .................................................................. 20
Comparator User Module Electrical Specifications
(CY8C24193/493) .................................................................. 20
ADC Electrical Specifications (CY8C24193/493) ........... 21
DC POR and LVD Specifications
(CY8C24193/493) .................................................................. 22
DC Programming Specifications (CY8C24193/493) ...... 22
DC I2C Specifications (CY8C24193/493) ...................... 23
Shield Driver DC Specifications (CY8C24193/493) ....... 23
DC IDAC Specifications (CY8C24193/493) ................... 23
AC Chip-Level Specifications (CY8C24193/493) ........... 24
AC General Purpose I/O Specifications
(CY8C24193/493) .................................................................. 25
AC Comparator Specifications (CY8C24193/493) ......... 25
AC External Clock Specifications (CY8C24193/493) ..... 25
AC Programming Specifications (CY8C24193/493) ...... 26
AC I2C Specifications (CY8C24193/493) ...................... 27
Electrical Specifications (CY8C24093/293/393/693) ......... 30
Absolute Maximum Ratings
(CY8C24093/293/393/693) .................................................... 30
Operating Temperature
Document Number: 001-86894 Rev. *A
(CY8C24093/293/393/693) ....................................................30
DC Chip-Level Specifications
(CY8C24093/293/393/693) ....................................................31
DC GPIO Specifications (CY8C24093/293/393/693) .....32
DC Analog Mux Bus Specifications
(CY8C24093/293/393/693) ....................................................34
DC Low Power Comparator Specifications
(CY8C24093/293/393/693) ....................................................34
Comparator User Module Electrical Specifications
(CY8C24093/293/393/693) ....................................................35
ADC Electrical Specifications
(CY8C24093/293/393/693) ....................................................35
DC POR and LVD Specifications
(CY8C24093/293/393/693) ....................................................36
DC Programming Specifications
(CY8C24093/293/393/693) ....................................................36
DC I2C Specifications (CY8C24093/293/393/693) .........37
DC Reference Buffer Specifications
(CY8C24093/293/393/693) ....................................................37
DC IDAC Specifications (CY8C24093/293/393/693) ......37
AC Chip-Level Specifications
(CY8C24093/293/393/693) ....................................................38
AC GPIO Specifications
(CY8C24093/293/393/693) ....................................................39
AC Comparator Specifications
(CY8C24093/293/393/693) ....................................................40
AC External Clock Specifications
(CY8C24093/293/393/693) ....................................................40
AC Programming Specifications
(CY8C24093/293/393/693) ....................................................41
AC I2C Specifications (CY8C24093/293/393/693) .........42
Packaging Information .........................................................45
Thermal Impedances ......................................................48
Capacitance on Crystal Pins ..........................................48
Solder Reflow Specifications ..........................................48
Development Tool Selection ...............................................49
Software .........................................................................49
Development Kits ...........................................................49
Evaluation Tools .............................................................49
Device Programmers ......................................................49
Ordering Information ...........................................................50
Ordering Code Definitions ..............................................50
Acronyms ..............................................................................51
Reference Documents .........................................................51
Document Conventions .......................................................51
Units of Measure ............................................................51
Numeric Naming .............................................................52
Glossary ................................................................................52
Document History Page .......................................................53
Sales, Solutions, and Legal Information ............................54
Worldwide Sales and Design Support ............................54
Products .........................................................................54
PSoC Solutions ..............................................................54
Page 3 of 54
CY8C24X93
PSoC® Functional Overview
The PSoC family consists of on-chip controller devices, which
are designed to replace multiple traditional microcontroller unit
(MCU)-based components with one, low cost single-chip
programmable component. A PSoC device includes
configurable analog and digital blocks, and programmable
interconnect. This architecture allows the user to create
customized peripheral configurations, to match the requirements
of each individual application. Additionally, a fast CPU, Flash
program memory, SRAM data memory, and configurable I/O are
included in a range of convenient pinouts.
The architecture for this device family, as shown in the Logic
Block Diagram on page 2, consists of three main areas:
■
The Core
■
Analog System
■
System Resources (including a full-speed USB port).
reference. All the pins can be configured to connect to the analog
system.
ADC
The ADC in the CY8C24x93 device is an incremental
analog-to-digital converter with a range of 8 to 10 bits supporting
signed and unsigned data formats. The input to the ADC can be
from any pin.
IDAC
The IDAC can provide current source up to 512 µA to any GPIO
pin. In the CY8C24x93 family of devices 4 ranges of current
source can be implemented that can vary in 255 steps, and are
connected to analog mux bus.
Table 1. IDAC Ranges
A common, versatile bus allows connection between I/O and the
analog system.
Depending on the PSoC package, up to 36 GPIO are included in
the CY8C24x93 PSoC device. The GPIO provides access to the
MCU and analog mux.
PSoC Core
The PSoC Core is a powerful engine that supports a rich
instruction set. It encompasses SRAM for data storage, an
interrupt controller, sleep and watchdog timers, and IMO and
ILO. The CPU core, called the M8C, is a powerful processor with
speeds up to 24 MHz. The M8C is a 4-MIPS, 8-bit
Harvard-architecture microprocessor.
Analog system
The analog system is composed of an ADC, two comparators
and an IDAC. It has an internal 0.8 V, 1 V or 1.2 V analog
Document Number: 001-86894 Rev. *A
Range
Full Scale Range in µA
1x
64
2x
128
4x
256
8x
512
Comparator
The CY8C24x93 family has two high-speed, low-power
comparators. The comparators have three voltage references,
0.8 V, 1.0 V and 1.2 V. Comparator inputs can be connected from
any pin through the analog mux bus. The comparator output can
be read in firmware for processing or routed out via specific pins
(P1_0 or P1_4).
The output of the two comparators can be combined with 2-input
logic functions. The combinatorial output can be optionally
combined with a latched value and routed to a pin output or to
the interrupt controller. The input multiplexers and the
comparator are controller through the CMP User Module.
Page 4 of 54
CY8C24X93
Analog Multiplexer System
■
The Analog Mux Bus can connect to every GPIO pin and can be
internally connected to the ADC, Comprators or the IDAC.
Other multiplexer applications include:
■
Chip-wide mux that allows analog input from any I/O pin.
■
Crosspoint connection between any I/O pin combinations.
Additional System Resources
System resources provide additional capability, such as
configurable USB and I2C slave, SPI master/slave
communication interface, three 16-bit programmable timers,
software 8-bit PWM, low voltage detect, power on reset, and
various system resets supported by the M8C.
The merits of each system resource are listed here:
Document Number: 001-86894 Rev. *A
The I2C slave/SPI master-slave module provides
50/100/400 kHz communication over two wires. SPI
communication over three or four wires runs at speeds of
46.9 kHz to 3 MHz (lower for a slower system clock).
■
Low-voltage detection (LVD) interrupts can signal the
application of falling voltage levels, while the advanced
power-on-reset (POR) circuit eliminates the need for a system
supervisor.
■
A register-controlled bypass mode allows the user to disable
the LDO regulator.
■
An 8-bit Software PWM is provided for applications like buzzer
control or lighting control. A 16-bit Timer acts as the input clock
to the PWM. The ISR increments a software counter (8-bit),
checks for PWM compare condition and toggles a GPIO
accordingly. PWM Output is available on all GPIOs.
Page 5 of 54
CY8C24X93
Getting Started
The quickest way to understand PSoC silicon is to read this
datasheet and then use the PSoC Designer Integrated
Development Environment (IDE). This datasheet is an overview
of the PSoC integrated circuit and presents specific pin, register,
and electrical specifications.
For in depth information, along with detailed programming
details, see the Technical Reference Manual for the PSoC
devices.
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Training
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
CYPros Consultants
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web
at www.cypress.com/psoc.
Certified PSoC consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC consultant go to the CYPros Consultants web site.
Silicon Errata
Solutions Library
Errata documents known issues with silicon including errata
trigger conditions, scope of impact, available workarounds and
silicon revision applicability. The Silicon Errata for the PSoC®
CY8C24x93 family is available here.
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Development Kits
Technical Support
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Document Number: 001-86894 Rev. *A
Page 6 of 54
CY8C24X93
Development Tools
PSoC Designer™ is the revolutionary integrated design
environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
Code Generation Tools
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
■
Integrated source-code editor (C and assembly)
Debugger
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also lets you to create a trace buffer of registers and memory
locations of interest.
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up
to
four
full-duplex
universal
asynchronous
receiver/transmitters (UARTs), SPI master and slave, and
wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
■
PSoC Designer Software Subsystems
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer.
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are analog-to-digital converters (ADCs),
digital-to-analog converters (DACs), amplifiers, and filters.
Configure the user modules for your chosen application and
connect them to each other and to the proper pins. Then
generate your project. This prepopulates your project with APIs
and libraries that you can use to program your application.
The tool also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic
reconfiguration makes it possible to change configurations at run
time. In essence, this lets you to use more than 100 percent of
PSoC’s resources for an application.
Document Number: 001-86894 Rev. *A
In-Circuit Emulator
A low-cost, high-functionality in-circuit emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Page 7 of 54
CY8C24X93
Designing with PSoC Designer
The development process for the PSoC device differs from that
of a traditional fixed-function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and lowering inventory costs. These
configurable resources, called PSoC blocks, have the ability to
implement a wide variety of user-selectable functions. The PSoC
development process is:
1. Select user modules.
2. Configure user modules.
3. Organize and connect.
4. Generate, verify, and debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules”. User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a PWM
User Module configures one or more digital PSoC blocks, one
for each eight bits of resolution. Using these parameters, you can
establish the pulse width and duty cycle. Configure the
parameters and properties to correspond to your chosen
application. Enter values directly or by selecting values from
drop-down menus. All of the user modules are documented in
datasheets that may be viewed directly in PSoC Designer or on
the Cypress website. These user module datasheets explain the
Document Number: 001-86894 Rev. *A
internal operation of the user module and provide performance
specifications. Each datasheet describes the use of each user
module parameter, and other information that you may need to
successfully implement your design.
Organize and Connect
Build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. Perform the selection,
configuration, and routing so that you have complete control over
all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides APIs with high-level functions to control
and respond to hardware events at run time, and interrupt
service routines that you can adapt as needed.
A complete code development environment lets you to develop
and customize your applications in C, assembly language, or
both.
The last step in the development process takes place inside
PSoC Designer’s Debugger (accessed by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full-speed. PSoC Designer debugging
capabilities rival those of systems costing many times more. In
addition to traditional single-step, run-to-breakpoint, and
watch-variable features, the debug interface provides a large
trace buffer. It lets you to define complex breakpoint events that
include monitoring address and data bus values, memory
locations, and external signals.
Page 8 of 54
CY8C24X93
Pinouts
16-pin QFN (13 GPIOs) [2]
Table 2. Pin Definitions – CY8C24093 [3]
I/O
I
P2[5] Crystal output (XOut)
2
I/O
I
P2[3] Crystal input (XIn)
3
IOHR
I
P1[7] I2C SCL, SPI SS
2
4
IOHR
I
P1[5] I C SDA, SPI MISO
5
IOHR
I
P1[3] SPI CLK
6
IOHR
I
P1[1] ISSP CLK[4], I2C SCL, SPI
MOSI
7
Power
VSS
IOHR
I
P1[0] ISSP DATA[4], I2C SDA, SPI
CLK[5]
9
IOHR
I
P1[2]
10
IOHR
I
P1[4] Optional external clock
(EXTCLK)
12
13
Input
IOH
P0[1], AI
P0[3], AI
P0[7], AI
VDD
AI , XOut, P2[5]
AI , XIn, P2[3]
AI , I2 C SCL, SPI SS, P1[7]
AI , I2 C SDA, SPI MISO, P1[5]
Ground connection
8
11
Figure 1. CY8C24093 Device
Description
XRES Active high external reset with
internal pull-down
I
P0[4]
Power
VDD
14
IOH
I
P0[7]
15
IOH
I
P0[3]
16
IOH
I
P0[1]
1
2
14
13
1
Name
16
15
Analog
12
11
(Top View)
10
3
9
4
QFN
5
6
7
8
Digital
P0[4] , AI
XRES
P1[4] , EXTCLK, AI
P1[2] , AI
AI, SPI CLK , P1[3]
AI, ISSP CLK, SPI MOSI, P1[1]
VSS
AI, ISSP DATA , I2C SDA, SPI CLK , P1[0]
Type
Pin
No.
Supply voltage
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
2. No center pad.
3. 13 GPIOs.
4. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
5. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 9 of 54
CY8C24X93
32-pin QFN (28 GPIOs) [6]
Table 3. Pin Definitions – CY8C24193 [7]
I
P0[1]
I/O
I
P2[7]
3
I/O
I
P2[5]
Crystal output (XOut)
4
I/O
I
P2[3]
Crystal input (XIn)
5
I/O
I
P2[1]
6
I/O
I
P3[3]
7
I/O
I
P3[1]
8
IOHR
I
P1[7]
I2C SCL, SPI SS
9
IOHR
I
P1[5]
I2C SDA, SPI MISO
10
IOHR
I
P1[3]
SPI CLK.
11
IOHR
I
P1[1]
ISSP CLK[8], I2C SCL, SPI MOSI.
P1[0]
14
IOHR
I
P1[2]
15
IOHR
I
P1[4]
16
IOHR
17
I
Input
ISSP DATA[8], I2C SDA,
SPI CLK[9]
Optional external clock input
(EXTCLK)
P1[6]
XRES
I/O
I
P3[0]
19
I/O
I
P3[2]
20
I/O
I
P2[0]
21
I/O
I
P2[2]
22
I/O
I
P2[4]
23
I/O
I
P2[6]
24
IOH
I
P0[0]
25
IOH
I
P0[2]
26
IOH
I
P0[4]
27
IOH
I
P0[6]
9
30
29
10
11
12
P0[0] , AI
P2[6] , AI
P2[4] , AI
P2[2] , AI
P2[0] , AI
P3[2] , AI
P3[0] , AI
XRES
[8]
18
Active high external reset with
internal pull-down
32
31
Vss
P0 [3], AI
P0 [5], AI
Ground connection.
15
16
I
AI, E XTCLK, P 1[4]
AI, P 1[6]
VSS
IOHR
QFN
(Top View)
24
23
22
21
20
19
18
17
13
14
Power
13
1
2
3
4
5
6
7
8
A I,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
[8]
AI , ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P 1[2]
12
AI , P0[1]
AI , P2[7]
AI, XOut, P2[5]
AI , XIn, P2[3]
AI , P2[1]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
P0 [4], AI
P0 [2], AI
IOH
2
Figure 2. CY8C24193
Description
26
25
1
Name
P0 [7], AI
Vd d
P0 [6], AI
Analog
28
27
Digital
AI, I2C SDA, SPI MISO, P 1[5]
AI, SPI CLK, P 1[3]
Type
Pin
No.
28
Power
VDD
29
IOH
I
P0[7]
30
IOH
I
P0[5]
31
IOH
I
P0[3]
Supply voltage
32
Power
VSS
Ground connection
CP
Power
VSS
Center pad must be connected to
ground
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
6. 28 GPIOs.
7. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
8. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
9. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 10 of 54
CY8C24X93
32-pin QFN (28 GPIOs) [10]
Table 4. Pin Definitions – CY8C24293 [11]
P2[5]
Crystal output (XOut)
3
I/O
I
P2[3]
Crystal input (XIn)
4
I/O
I
P2[1]
5
I/O
I
P4[3]
6
I/O
I
P3[3]
7
I/O
I
P3[1]
8
IOHR
I
P1[7]
I2C SCL, SPI SS
9
IOHR
I
P1[5]
I2C SDA, SPI MISO
10
IOHR
I
P1[3]
SPI CLK.
11
IOHR
I
P1[1]
ISSP CLK [12], I2C SCL, SPI MOSI.
12
Power
VSS
Ground connection
13
IOHR
I
P1[0]
ISSP DATA[12], I2C SDA, SPI CLK[13]
14
IOHR
I
P1[2]
15
IOHR
I
P1[4]
16
IOHR
I
P1[6]
17
Input
18
I/O
I
P3[0]
19
I/O
I
P3[2]
20
I/O
I
P4[0]
21
I/O
I
P4[2]
22
I/O
I
P2[0]
23
I/O
I
P2[2]
24
I/O
I
P2[4]
25
IOH
I
P0[0]
26
IOH
I
P0[2]
27
IOH
I
P0[4]
28
IOH
I
P0[6]
29
Power
30
IOH
I
P0[7]
31
IOH
I
P0[3]
32
Power
VSS
Ground connection
CP
Power
VSS
Center pad must be connected to
ground
AI , XOut ,P0[1]
AI , XIn ,P2[5]
AI ,P2[3]
AI ,P2[ 1]
AI ,P4[3]
AI ,P3[3]
AI ,P3[1]
AI ,I2 C SCL, SPI SS,P1[7]
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P0 [4 ], AI
P0 [2 ], AI
P0 [0 ], AI
P0[1]
I
1
2
3
4
5
6
7
8
QFN
(Top View)
24
23
22
21
20
19
18
17
P2[4] ,AI
P2[2] ,AI
P2[0] ,AI
P4[2] ,AI
P4[0] ,AI
P3[2] ,AI
P3[0] ,AI
XRES
AI, EXTCLK, P 1[ 4]
AI, P 1[ 6]
I
I/O
Vss
P0 [3 ], AI
P0 [7 ], AI
VDD
P0[6], AI
IOH
2
32
31
30
29
28
27
26
25
1
XRES
Figure 3. CY8C24293 Device
Description
9
Name
10
11
12
13
14
15
16
Analog
AI, I2C SDA , SPI MI SO, P 1[ 5]
A I, SP I CLK, P 1[ 3]
AI ,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
[12]
AI ,ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P 1[ 2]
Digital
[12]
Pin
No.
VDD
LEGEND A = Analog, I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Notes
10. 28 GPIOs.
11. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
12. On power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to high impedance state. On reset, after XRES de-asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use
alternate pins if you encounter issues.
13. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 11 of 54
CY8C24X93
48-pin QFN (34 GPIOs) [14]
Table 5. Pin Definitions – CY8C24393, CY8C24693 [15, 16]
Power
22
IOHR
I
P1[0]
23
24
IOHR
IOHR
I
I
P1[2]
P1[4]
25
26
IOHR
Input
I
P1[6]
XRES
27
28
29
30
31
32
33
34
35
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
AI , XIn ,P2[3]
AI ,P2[1]
AI ,P4[3]
AI ,P4[1]
AI ,P3[7]
AI ,P3[5]
AI ,P3[3]
AI P3[1]
AI ,I2 C SCL, SPI SS,P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
No connection
No connection
SPI CLK
ISSP CLK[17], I2C SCL, SPI MOSI
Ground connection
No connection
No connection
Supply voltage
ISSP DATA[17], I2C SDA, SPI CLK[18]
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P3[0]
P3[2]
P3[4]
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
1
2
Pin
No.
36
Digital
Analog
5
6
Name
IOH
IOH
I
I
P0[0]
P0[2]
39
40
IOH
IOH
I
I
P0[4]
P0[6]
41
42
43
44
45
46
47
48
CP
Power
IOH
Power
IOH
Power
I
I
P0[2], AI
P0[0], AI
Vd d
P0[6], AI
P0[4], AI
(Top View)
37
38
I
NC ,
P0[7], AI
NC
NC
QFN
7
8
9
10
11
12
36
35
34
33
32
31
3
4
NC
IOH
38
37
NC
AI ,P2[7]
AI , XOut,P2[5]
42
41
40
39
Crystal output (XOut)
Crystal input (XIn)
46
45
44
43
I
I
No connection
15
16
17
18
19
20
21
22
23
24
IOHR
IOHR
Power
NC
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
NC
NC
P1[3]
P1[1]
VSS
NC
NC
VDD
P0[1], AI
Vss
P0[3], AI
I
I
I
I
I
I
I
I
I
I
I
I
Figure 4. CY8C24393, CY8C24693 Device
Description
48
47
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
13
14
Analog
30
29
28
27
26
25
NC
P2[ 4], AI
P2[ 2], AI
P2[ 0], AI
P4[ 2], AI
P4[ 0], AI
P3[ 6], AI
P3[ 4], AI
P3[ 2], AI
P3[0], AI
XRES
P1[ 6], AI
NC
NC
SPI C LK, A I, P1[3]
AI, ISSP C LK, I2C SCL, SPI MOSI, P1[1]
Vss
NC
NC
Vdd
1
AI, ISSP DATA , I2C SDA, SPI CLK, P1[0]
AI, P1 [2 ]
AI, EXTCL K, P1[4]
Digital
I2 C SD A, SPI MIS O, A I, P1[5]
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
VDD
NC
NC
P0[7]
NC
P0[3]
VSS
P0[1]
VSS
Description
No connection
Supply voltage
No connection
No connection
No connection
Ground connection
Center pad must be connected to
ground
LEGENDA = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
14. 38 GPIOs.
15. This part is available in limited quantities for In-Circuit Debugging during prototype development. It is not available in production volumes.
16. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
17. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
18. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 12 of 54
CY8C24X93
48-pin QFN (36 GPIOs (With USB)) [19]
Table 6. Pin Definitions – CY8C24493 [20, 21]
IOHR
I
IOHR
I
Power
I/O
I/O
Power
IOHR
I
NC
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
NC
NC
P1[3]
P1[1]
VSS
D+
DVDD
P1[0]
23
24
IOHR
IOHR
P1[2]
P1[4]
25
26
IOHR
I
Input
I
I
P1[6]
XRES
27
28
29
I/O
I/O
I/O
I
I
I
P3[0]
P3[2]
P3[4]
30
31
32
33
34
35
36
37
38
39
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOH
IOH
IOH
I
I
I
I
I
I
I
I
I
I
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
P2[6]
P0[0]
P0[2]
P0[4]
No connection
Crystal output (XOut)
Crystal input (XIn)
NC
AI , P2[7]
AI , XOut, P2[5]
AI , XIn , P2[3]
AI , P2[1]
AI , P4[3]
AI , P4[1]
AI , P3[7]
AI , P3[5]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
No connection
No connection
SPI CLK
ISSP CLK[20], I2C SCL, SPI MOSI
Ground connection
USB D+
USB DSupply voltage
ISSP DATA[20], I2C SDA, SPI
CLK[22]
Vss
P0[3], AI
P0[5 ], AI
P0[7], AI
NC
NC
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
I
I
I
I
I
I
I
I
I
I
I
I
Figure 5. CY8C24493
Description
P0[1], AI
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
48
47
46
45
44
43
42
41
40
39
38
37
Analog
1
2
3
4
5
6
7
8
9
10
11
12
QFN
(Top View)
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Digital
36
35
34
33
32
31
30
29
28
27
26
25
P2[6] , AI
P2[4] ,AI
P2[2] ,AI
P2[0] ,AI
P4[2] ,AI
P4[0] ,AI
P3[6] ,AI
P3[4] , AI
P3[2] ,AI
P3[0] , AI
XRES
P1[6] , AI
I2C SDA, SPI MISO, A I, P1[5]
NC
NC
SPI CLK, A I, P1[3]
[20]
AI,ISSP CLK , I2C SCL, SPI MOSI, P1[1]
Vss
D+
DVdd
[20, 22]
AI,ISSP DATA, I2C SDA, SPI CLK, P1[0]
AI, P1[2]
AI, EXTCLK, P1[4]
Pin
No.
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
Pin
No.
40
41
42
43
44
45
46
47
48
CP
Digital
IOH
IOH
IOH
IOH
Analog
I
Power
I
I
I
Power
IOH
I
Power
Name
P0[6]
VDD
NC
NC
P0[7]
P0[5]
P0[3]
VSS
P0[1]
VSS
Description
Supply voltage
No connection
No connection
Ground connection
Center pad must be connected to ground
LEGEND A = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
19. 36 GPIOs.
20. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
21. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
22. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 13 of 54
CY8C24X93
48-pin QFN (OCD) (36 GPIOs) [23]
The 48-pin QFN part is for the CY8C240093 On-Chip Debug (OCD). Note that this part is only used for in-circuit debugging.
Table 7. Pin Definitions – CY8C240093 [24, 25]
I
I
18
19
20
21
22
Power
IOHR
I
VSS
D+
DVDD
P1[0]
23
IOHR
I
P1[2]
24
IOHR
I
P1[4]
25
26
IOHR
I
Input
27
28
29
30
31
32
33
34
35
36
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
I
I
I
I
I
I
I
P1[6]
XRES
OCD mode direction pin
Crystal output (XOut)
Crystal input (XIn)
OCDO
A E
, P2[7]
I
AI , XOut, P2[5]
AI , XIn , P2[3]
AI , P2[1]
AI , P4[3]
AI , P4[1]
AI , P3[7]
AI , P3[5]
AI , P3[3]
AI , P3[1]
AI , I2 C SCL, SPI SS, P1[7]
I2C SCL, SPI SS
I2C SDA, SPI MISO
OCD CPU clock output
OCD high speed clock output
SPI CLK.
ISSP CLK[27], I2C SCL, SPI
MOSI
Ground connection
USB D+
USB DSupply voltage
ISSP DATA[27], I2C SDA, SPI
CLK[28]
Optional external clock input
(EXTCLK)
Active high external reset with
internal pull-down
P3[0]
P3[2]
P3[4]
P3[6]
P4[0]
P4[2]
P2[0]
P2[2]
P2[4]
P2[6]
OCDO
Vdd
P0[6], AI
P0[4], AI
P0[2], AI
P0[0], AI
IOHR
IOHR
OCDOE
P2[7]
P2[5]
P2[3]
P2[1]
P4[3]
P4[1]
P3[7]
P3[5]
P3[3]
P3[1]
P1[7]
P1[5]
CCLK
HCLK
P1[3]
P1[1]
Vss
P0[3], AI
P0[5 ], AI
P0[7], AI
OCDE
I
I
I
I
I
I
I
I
I
I
I
I
Figure 6. CY8C240093
Description
P0[1], AI
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
IOHR
IOHR
Name
48
47
46
45
44
43
42
41
40
39
38
37
Analog
1
2
3
4
5
6
7
8
9
10
11
12
QFN
(Top View)
13
14
15
16
17
18
19
20
21
22
23
24
1[26]
2
3
4
5
6
7
8
9
10
11
12
13
14[26]
15[26]
16
17
Digital
36
35
34
33
32
31
30
29
28
27
26
25
P2[6] , AI
P2[4] , AI
P2[2] , AI
P2[0] , AI
P4[2] , AI
P4[0] , AI
P3[6] , AI
P3[4] , AI
P3[2] , AI
P3[0] , AI
XRES
P1[6] , AI
I2C SDA, SPI MISO, AI, P1[5]
CCLK
HCLK
SPI CLK, A I, P1[3]
[27]
AI,ISSP CLK6, I2C SCL, SPI MOSI, P1[1]
Vss
D+
DVdd
[27, 28]
AI,ISSP DATA1 , I2C SDA, SPI CLK, P1[0]
AI, P1[2]
AI, EXTCLK, P1[4]
Pin
No.
Pin
No.
37
Digital
Analog
IOH
I
P0[0]
38
39
IOH
IOH
I
I
P0[2]
P0[4]
40
41
42[26]
43[26]
44
45
46
47
48
CP
IOH
I
P0[6]
VDD
OCDO
OCDE
P0[7]
P0[5]
P0[3]
VSS
P0[1]
VSS
Power
IOH
IOH
IOH
I
I
I
Power
IOH
I
Power
Name
Description
Supply voltage
OCD even data I/O
OCD odd data output
Ground connection
Center pad must be connected to
ground
LEGEND A = Analog, I = Input, O = Output, NC = No Connection H = 5 mA High Output Drive, R = Regulated Output.
Notes
23. 36 GPIOs.
24. This part is available in limited quantities for In-Circuit Debugging during prototype development. It is not available in production volumes.
25. The center pad (CP) on the QFN package must be connected to ground (VSS) for best mechanical, thermal, and electrical performance. If not connected to ground,
it must be electrically floated and not connected to any other signal.
26. This pin (associated with OCD part only) is required for connecting the device to ICE-Cube In-Circuit Emulator for firmware debugging purpose. To know more about
the usage of ICE-Cube, refer to CY3215-DK PSoC® IN-CIRCUIT EMULATOR KIT GUIDE.
27. On Power-up, the SDA(P1[0]) drives a strong high for 256 sleep clock cycles and drives resistive low for the next 256 sleep clock cycles. The SCL(P1[1]) line drives
resistive low for 512 sleep clock cycles and both the pins transition to High impedance state. On reset, after XRES de- asserts, the SDA and the SCL lines drive
resistive low for 8 sleep clock cycles and transition to high impedance state. In both cases, a pull-up resistance on these lines combines with the pull-down resistance
(5.6K ohm) and form a potential divider. Hence, during power-up or reset event, P1[1] and P1[0] may disturb the I2C bus. Use alternate pins if you encounter issues.
28. Alternate SPI clock.
Document Number: 001-86894 Rev. *A
Page 14 of 54
CY8C24X93
Electrical Specifications (CY8C24193/493)
This section presents the DC and AC electrical specifications of the CY8C24193/493 PSoC devices. For the latest electrical
specifications, confirm that you have the most recent datasheet by visiting the web at http://www.cypress.com/psoc.
Figure 7. Voltage versus CPU Frequency
5.5 V
VDD Voltage
li d ng
Va rati n
e io
Op Reg
1.71 V
750 kHz
3 MHz
CPU
24 MHz
Frequency
Absolute Maximum Ratings (CY8C24193/493)
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 8. Absolute Maximum Ratings
Symbol
Description
Conditions
Min
Typ
Max
Units
TSTG
Storage temperature
Higher storage temperatures reduce data
retention time. Recommended Storage
Temperature is +25 °C ± 25 °C. Extended
duration storage temperatures above 85 °C
degrades reliability.
–55
+25
+125
°C
VDD
Supply voltage relative to VSS
–
–0.5
–
+6.0
V
VIO
DC input voltage
–
VSS – 0.5
–
VDD + 0.5
V
VIOZ
DC voltage applied to tristate
–
VSS – 0.5
–
VDD + 0.5
V
IMIO
Maximum current into any port pin
–
–25
–
+50
mA
ESD
Electro static discharge voltage
Human body model ESD
2000
–
–
V
LU
Latch up current
In accordance with JESD78 standard
–
–
200
mA
Min
Typ
Max
Units
–
+85
°C
70
°C
+100
°C
Operating Temperature (CY8C24193/493)
Table 9. Operating Temperature
Symbol
Description
Conditions
TA
Ambient temperature
–
–40
TC
Commercial temperature range
–
0
TJ
Operational die temperature
The temperature rise from ambient to junction
is package specific. See the Thermal
Impedances on page 48. The user must limit
the power consumption to comply with this
requirement.
Document Number: 001-86894 Rev. *A
–40
–
Page 15 of 54
CY8C24X93
DC Chip-Level Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 10. DC Chip-Level Specifications
Symbol
VDD
[29, 43]
Description
Supply voltage
Conditions
See table DC POR and LVD Specifications
(CY8C24093/293/393/693) on page 36
Min
Typ
Max
Units
1.71
–
5.50
V
IDD24
Supply current, IMO = 24 MHz Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 24 MHz.
–
2.88
4.00
mA
IDD12
Supply current, IMO = 12 MHz Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 12 MHz.
–
1.71
2.60
mA
IDD6
Supply current, IMO = 6 MHz
Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 6 MHz.
–
1.16
1.80
mA
ISB0
Deep sleep current
VDD  3.0 V, TA = 25 °C, I/O regulator turned off
–
0.10
1.1
A
ISB1
Standby current with POR, LVD VDD  3.0 V, TA = 25 °C, I/O regulator turned off
and sleep timer
–
1.07
1.50
A
ISBI2C
Standby current with I2C
enabled
–
1.64
–
A
Conditions are VDD = 3.3 V, TA = 25 °C and
CPU = 24 MHz
Notes
29. When VDD remains in the range from 1.71 V to 1.9 V for more than 50 µs, the slew rate when moving from the 1.71 V to 1.9 V range to greater than 2 V must be
slower than 1 V/500 µs to avoid triggering POR. The only other restriction on slew rates for any other voltage range or transition is the SRPOWER_UP parameter.
30. If powering down in standby sleep mode, to properly detect and recover from a VDD brown out condition any of the following actions must be taken:
a. Bring the device out of sleep before powering down.
b. Assure that VDD falls below 100 mV before powering back up.
c. Set the No Buzz bit in the OSC_CR0 register to keep the voltage monitoring circuit powered during sleep.
d. Increase the buzz rate to assure that the falling edge of VDD is captured. The rate is configured through the PSSDC bits in the SLP_CFG register. For the referenced
registers, refer to the Technical Reference Manual. In deep sleep/standby sleep mode, additional low power voltage monitoring circuitry allows VDD brown out
conditions to be detected and resets the device when VDD goes lower than 1.1 V at edge rates slower than 1 V/ms.
Document Number: 001-86894 Rev. *A
Page 16 of 54
CY8C24X93
DC GPIO Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 11. 3.0 V to 5.5 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ Max Units
RPU
Pull-up resistor
–
4
5.60
8
k
VOH1
High output voltage
Port 2 or 3 pins
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH2
High output voltage
Port 2 or 3 Pins
IOH = 1 mA, maximum of 20 mA source
current in all I/Os
VDD – 0.90
–
–
V
VOH3
High output voltage
IOH < 10 A, maximum of 10 mA source
Port 0 or 1 pins with LDO regulator Disabled current in all I/Os
for port 1
VDD – 0.20
–
–
V
VOH4
High output voltage
IOH = 5 mA, maximum of 20 mA source
Port 0 or 1 pins with LDO regulator Disabled current in all I/Os
for port 1
VDD – 0.90
–
–
V
VOH5
IOH < 10 A, VDD > 3.1 V, maximum of
High output voltage
Port 1 Pins with LDO Regulator Enabled for 4 I/Os all sourcing 5 mA
3 V out
2.85
VOH6
High output voltage
IOH = 5 mA, VDD > 3.1 V, maximum of 20 mA
Port 1 pins with LDO regulator enabled for source current in all I/Os
3 V out
2.20
VOH7
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
2.35
VOH8
High output voltage
IOH = 2 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
1.90
VOH9
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.60
VOH10
High output voltage
IOH = 1 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
IOL = 25 mA, VDD > 3.3 V, maximum of 60 mA
sink current on even port pins (for example,
P0[2] and P1[4]) and 60 mA sink current on
odd port pins (for example, P0[3] and P1[5])
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.80
V
3.00 3.30
–
–
2.50 2.75
–
–
1.80 2.10
V
V
V
V
V
VIH
Input high voltage
–
2.00
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (Absolute Value)
–
–
0.00
1
1
A
CPIN
Pin capacitance
Package and pin dependent
Temp = 25 °C
0.50
1.70
7
pF
VILLVT3.3 Input Low Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
0.8
V
–
–
VIHLVT3.3 Input High Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
1.4
–
–
V
VILLVT5.5 Input Low Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
0.8
V
–
–
VIHLVT5.5 Input High Voltage with low threshold enable Bit3 of IO_CFG1 set to enable low threshold
set, Enable for Port1
voltage of Port1 input
1.7
–
–
V
Document Number: 001-86894 Rev. *A
Page 17 of 54
CY8C24X93
Table 12. 2.4 V to 3.0 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH < 10 A, maximum of 10 mA source VDD - 0.20
current in all I/Os
–
–
V
High output voltage
Port 2 or 3 Pins
IOH = 0.2 mA, maximum of 10 mA
source current in all I/Os
VDD - 0.40
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH < 10 A, maximum of 10 mA source VDD - 0.20
current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD - 0.50
current in all I/Os
–
–
V
VOH5A
IOH < 10 A, VDD > 2.4 V, maximum of
High output voltage
Port 1 pins with LDO enabled for 1.8 V 20 mA source current in all I/Os
out
1.50
1.80
2.10
V
VOH6A
High output voltage
IOH = 1 mA, VDD > 2.4 V, maximum of
Port 1 pins with LDO enabled for 1.8 V 20 mA source current in all I/Os
out
1.20
–
–
V
VOL
Low output voltage
IOL = 10 mA, maximum of 30 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.72
V
VIH
Input high voltage
–
1.40
–
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
Temp = 25 C
0.50
1.70
7
pF
VILLVT2.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low
threshold voltage of Port1 input
0.7
V
–
VIHLVT2.5 Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low
threshold voltage of Port1 input
1.2
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 pins
VOH2
Document Number: 001-86894 Rev. *A
V
–
V
Page 18 of 54
CY8C24X93
Table 13. 1.71 V to 2.4 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH = 10 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
High output voltage
Port 2 or 3 pins
IOH = 0.5 mA, maximum of 10 mA VDD – 0.50
source current in all I/Os
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 100 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD – 0.50
current in all I/Os
–
–
V
VOL
Low output voltage
IOL = 5 mA, maximum of 20 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
–
0.40
V
VIL
Input low voltage
–
–
–
0.30 × VDD
V
VIH
Input high voltage
–
0.65 × VDD
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
temp = 25 C
0.50
1.70
7
pF
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 pins
VOH2
Table 14. GPIO Current Sink and Source Specifications
Supply
Voltage
Mode
Port 1 per I/O (max)
Port 2/3/4 per
I/O (max)
Total Current Even
Pins (max)
Total Current Odd
Pins (max)
Units
1.71 – 2.4
Sink
5
5
20
30
mA
2.4 – 3.0
3.0 – 5.0
Source
2
0.5
Sink
10
10
Source
2
0.2
Sink
25
25
Source
5
1
10[31]
30
mA
30
mA
60
mA
10[31]
60
20[31]
mA
mA
Note
31. Total current (odd + even ports)
Document Number: 001-86894 Rev. *A
Page 19 of 54
CY8C24X93
DC Analog Mux Bus Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 15. DC Analog Mux Bus Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
RSW
Switch resistance to common analog
bus
–
–
–
800

RGND
Resistance of initialization switch to
VSS
–
–
–
800

The maximum pin voltage for measuring RSW and RGND is 1.8 V
DC Low Power Comparator Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 16. DC Comparator Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0.2
–
1.8
V
VLPC
Low power comparator (LPC) common Maximum voltage limited to VDD
mode
ILPC
LPC supply current
–
–
10
80
A
VOSLPC
LPC voltage offset
–
–
2.5
30
mV
Comparator User Module Electrical Specifications (CY8C24193/493)
The following table lists the guaranteed maximum and minimum specifications. Unless stated otherwise, the specifications are for the
entire device voltage and temperature operating range: –40 °C  TA  85 °C, 1.71 V  VDD  5.5 V.
Table 17. Comparator User Module Electrical Specifications
Symbol
Min
Typ
Max
Units
50 mV overdrive
–
70
100
ns
Offset
Valid from 0.2 V to 1.5 V
–
2.5
30
mV
Current
Average DC current, 50 mV
overdrive
–
20
80
µA
Supply voltage > 2 V
Power supply rejection ratio
–
80
–
dB
Supply voltage < 2 V
Power supply rejection ratio
–
40
–
dB
1.5
V
TCOMP
PSRR
Description
Comparator response time
Input range
Document Number: 001-86894 Rev. *A
Conditions
–
0.2
Page 20 of 54
CY8C24X93
ADC Electrical Specifications (CY8C24193/493)
Table 18. ADC User Module Electrical Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0
–
VREFADC
V
Input
VIN
Input voltage range
CIIN
Input capacitance
–
RIN
Input resistance
Equivalent switched cap input
resistance for 8-, 9-, or 10-bit
resolution
ADC reference voltage
FCLK
–
–
–
5
pF
1/(500fF ×
data clock)
1/(400fF ×
data clock)
1/(300fF ×
data clock)

–
1.14
–
1.26
V
Data clock
Source is chip’s internal main
oscillator. See AC Chip-Level
Specifications on page 24 for
accuracy
2.25
–
6
MHz
S8
8-bit sample rate
Data clock set to 6 MHz.
sample rate = 0.001/
(2^Resolution/Data Clock)
–
23.43
–
ksps
S10
10-bit sample rate
Data clock set to 6 MHz.
sample rate = 0.001/
(2^resolution/data clock)
–
5.85
–
ksps
Reference
VREFADC
Conversion Rate
DC Accuracy
RES
Resolution
Can be set to 8, 9, or 10 bit
8
–
10
bits
DNL
Differential nonlinearity
–
–1
–
+2
LSB
INL
Integral nonlinearity
–
–2
–
+2
LSB
EOFFSET
Offset error
8-bit resolution
0
3.20
19.20
LSB
10-bit resolution
0
12.80
76.80
LSB
EGAIN
Gain error
For any resolution
–5
–
+5
%FSR
IADC
Operating current
–
–
2.10
2.60
mA
PSRR
Power supply rejection ratio
Power
Document Number: 001-86894 Rev. *A
PSRR (VDD > 3.0 V)
–
24
–
dB
PSRR (VDD < 3.0 V)
–
30
–
dB
Page 21 of 54
CY8C24X93
DC POR and LVD Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 19. DC POR and LVD Specifications
Symbol
VPOR0
Description
Conditions
Min
Typ
Max
Units
1.61
–
1.66
1.71
V
2.36
2.41
–
2.60
2.66
–
2.82
2.95
VPOR2
1.66 V selected in PSoC Designer VDD must be greater than or equal to 1.71 V
2.36 V selected in PSoC Designer during startup, reset from the XRES pin, or
reset from watchdog.
2.60 V selected in PSoC Designer
VPOR3
2.82 V selected in PSoC Designer
VLVD0
2.45 V selected in PSoC Designer –
2.40
2.45
2.51
VLVD1
2.71 V selected in PSoC Designer
2.64[46]
2.71
2.78
VLVD2
2.92 V selected in PSoC Designer
2.85[47]
2.92
2.99
VLVD3
3.02 V selected in PSoC Designer
2.95[48]
3.02
3.09
VLVD4
3.13 V selected in PSoC Designer
3.06
3.13
3.20
VLVD5
1.90 V selected in PSoC Designer
1.84
1.90
2.32
VLVD6
1.80 V selected in PSoC Designer
1.75[49]
1.80
1.84
VLVD7
4.73 V selected in PSoC Designer
4.62
4.73
4.83
VPOR1
V
DC Programming Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 20. DC Programming Specifications
Symbol
Description
VDDIWRITE Supply voltage for flash write
operations
IDDP
Supply current during
programming or verify
VILP
Input low voltage during
programming or verify
VIHP
Input high voltage during
programming or verify
IILP
Input current when Applying VILP
to P1[0] or P1[1] during
programming or verify
IIHP
Input current when applying VIHP
to P1[0] or P1[1] during
programming or verify
VOLP
Output low voltage during
programming or verify
VOHP
Output high voltage during
programming or verify
FlashENPB Flash write endurance
FlashDR
Flash data retention
–
Conditions
Min
1.71
Typ
–
Max
5.25
Units
V
–
–
5
25
mA
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 32
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 32
Driving internal pull-down resistor
–
–
VIL
V
VIH
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
VSS + 0.75
V
VOH
–
VDD
V
50,000
20
–
–
–
–
–
Years
Driving internal pull-down resistor
See appropriate DC GPIO Specifications
(CY8C24093/293/393/693) on page 32.
For VDD > 3V use VOH4 in Table 36 on
page 32.
Erase/write cycles per block
Following maximum Flash write cycles;
ambient temperature of 55 °C
Notes
32. Always greater than 50 mV above VPPOR1 voltage for falling supply.
33. Always greater than 50 mV above VPPOR2 voltage for falling supply.
34. Always greater than 50 mV above VPPOR3 voltage for falling supply.
35. Always greater than 50 mV above VPPOR0 voltage for falling supply.
Document Number: 001-86894 Rev. *A
Page 22 of 54
CY8C24X93
DC I2C Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 21. DC I2C Specifications[36]
Symbol
VILI2C
VIHI2C
Description
Input low level
Input high level
Conditions
3.1 V ≤ VDD ≤ 5.5 V
Min
–
Typ
–
Max
Units
0.25 × VDD
V
2.5 V ≤ VDD ≤ 3.0 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 2.4 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 5.5 V
0.65 × VDD
–
VDD +
0.7 V[37]
V
Shield Driver DC Specifications (CY8C24193/493)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 22. Shield Driver DC Specifications
Symbol
VRef
Description
Reference buffer output
Conditions
1.7 V ≤ VDD ≤ 5.5 V
Min
0.942
Typ
–
Max
1.106
Units
V
VRefHi
Reference buffer output
1.7 V ≤ VDD ≤ 5.5 V
1.104
–
1.296
V
DC IDAC Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 23. DC IDAC Specifications (8-bit IDAC)
Symbol
Description
Min
Typ
Max
Units
Notes
IDAC_DNL
Differential nonlinearity
–1
–
1
LSB
IDAC_DNL
Integral nonlinearity
–2
–
2
LSB
IDAC_Current
Range = 4x
138
–
169
µA
DAC setting = 127 dec
Range = 8x
138
–
169
µA
DAC setting = 64 dec
Table 24. DC IDAC Specifications (7-bit IDAC)
Symbol
Description
Min
Typ
Max
Units
Notes
IDAC_DNL
Differential nonlinearity
–1
–
1
LSB
IDAC_DNL
Integral nonlinearity
–2
–
2
LSB
IDAC_Current
Range = 4x
137
–
168
µA
DAC setting = 127 dec
Range = 8x
138
–
169
µA
DAC setting = 64 dec
Notes
36. Pull-up resistors on I2C interface cannot be connected to a supply voltage that is more than 0.7 V higher than the CY8C24x93 power supply. See the CY8C24x93
Silicon Errata document for more details.
37. Please refer to Item # 6 of the CY8C24x93 Family.
Document Number: 001-86894 Rev. *A
Page 23 of 54
CY8C24X93
AC Chip-Level Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 25. AC Chip-Level Specifications
Min
Typ
Max
Units
FIMO24
Symbol
IMO frequency at 24 MHz Setting
Description
–
Conditions
22.8
24
25.2
MHz
FIMO12
IMO frequency at 12 MHz setting
–
11.4
12
12.6
MHz
FIMO6
IMO frequency at 6 MHz setting
–
5.7
6.0
6.3
MHz
FCPU
CPU frequency
–
0.75
–
25.20
MHz
F32K1
ILO frequency
–
15
32
50
kHz
F32K_U
ILO untrimmed frequency
–
13
32
82
kHz
DCIMO
Duty cycle of IMO
–
40
50
60
%
DCILO
ILO duty cycle
–
40
50
60
%
VDD slew rate during power-up
–
–
250
V/ms
After supply voltage is valid
1
–
–
ms
Applies after part has booted
10
–
–
s
SRPOWER_UP Power supply slew rate
tXRST
External reset pulse width at power-up
tXRST2
tJIT_IMO
External reset pulse width after
[39]
power-up[50]
6 MHz IMO cycle-to-cycle jitter (RMS)
–
–
0.7
6.7
ns
6 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
4.3
29.3
ns
6 MHz IMO period jitter (RMS)
–
–
0.7
3.3
ns
12 MHz IMO cycle-to-cycle jitter (RMS)
–
–
0.5
5.2
ns
12 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
2.3
5.6
ns
12 MHz IMO period jitter (RMS)
–
–
0.4
2.6
ns
24 MHz IMO cycle-to-cycle jitter (RMS)
–
–
1.0
8.7
ns
24 MHz IMO long term N cycle-to-cycle jitter
(RMS); N = 32
–
–
1.4
6.0
ns
24 MHz IMO period jitter (RMS)
–
–
0.6
4.0
ns
Note
38. The minimum required XRES pulse length is longer when programming the device (see Table 55 on page 41).
39. See the Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 001-86894 Rev. *A
Page 24 of 54
CY8C24X93
AC General Purpose I/O Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 26. AC GPIO Specifications
Symbol
FGPIO
Description
GPIO operating frequency
Conditions
Normal strong mode Port 0, 1
Min
0
0
tRISE23
tRISE23L
tRISE01
tRISE01L
tFALL
tFALLL
Rise time, strong mode, Cload = 50 pF
Ports 2 or 3
Rise time, strong mode low supply,
Cload = 50 pF, Ports 2 or 3
Rise time, strong mode, Cload = 50 pF
Ports 0 or 1
Rise time, strong mode low supply,
Cload = 50 pF, Ports 0 or 1
Fall time, strong mode, Cload = 50 pF
all ports
Fall time, strong mode low supply,
Cload = 50 pF, all ports
Typ
Max
Units
– 6 MHz for
MHz
1.71 V <VDD < 2.40 V
– 12 MHz for
MHz
2.40 V < VDD< 5.50 V
–
80
ns
VDD = 3.0 to 3.6 V, 10% to 90%
15
VDD = 1.71 to 3.0 V, 10% to 90%
15
–
80
ns
VDD = 3.0 to 3.6 V, 10% to 90%
LDO enabled or disabled
VDD = 1.71 to 3.0 V, 10% to 90%
LDO enabled or disabled
VDD = 3.0 to 3.6 V, 10% to 90%
10
–
50
ns
10
–
80
ns
10
–
50
ns
VDD = 1.71 to 3.0 V, 10% to 90%
10
–
70
ns
Figure 8. GPIO Timing Diagram
90%
GPIO Pin
Output
Voltage
10%
TRise23
TRise01
TRise23L
TRise01L
TFall
TFallL
AC Comparator Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 27. AC Low Power Comparator Specifications
Symbol
tLPC
Description
Comparator response time,
50 mV overdrive
Conditions
50 mV overdrive does not include
offset voltage.
Min
Typ
Max
Units
–
–
100
ns
AC External Clock Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 28. AC External Clock Specifications
Symbol
FOSCEXT
Description
Frequency (external oscillator
frequency)
Conditions
–
Min
Typ
Max
Units
0.75
–
25.20
MHz
High period
–
20.60
–
5300
ns
Low period
–
20.60
–
–
ns
Power-up IMO to switch
–
150
–
–
s
Document Number: 001-86894 Rev. *A
Page 25 of 54
CY8C24X93
AC Programming Specifications (CY8C24193/493)
Figure 9. AC Waveform
SCLK (P1[1])
T RSCLK
T FSCLK
SDATA (P1[0])
TSSCLK
T HSCLK
TDSCLK
The following table lists the guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 29. AC Programming Specifications
Symbol
tRSCLK
tFSCLK
tSSCLK
tHSCLK
FSCLK
tERASEB
tWRITE
tDSCLK
tDSCLK3
tDSCLK2
tXRST3
Description
Rise time of SCLK
Fall time of SCLK
Data setup time to falling edge of SCLK
Data hold time from falling edge of SCLK
Frequency of SCLK
Flash erase time (block)
Flash block write time
Data out delay from falling edge of SCLK
Data out delay from falling edge of SCLK
Data out delay from falling edge of SCLK
External reset pulse width after power-up
tXRES
tVDDWAIT
tVDDXRES
tPOLL
tACQ
XRES pulse length
VDD stable to wait-and-poll hold off
VDD stable to XRES assertion delay
SDAT high pulse time
“Key window” time after a VDD ramp
acquire event, based on 256 ILO clocks.
“Key window” time after an XRES event,
based on 8 ILO clocks
tXRESINI
Document Number: 001-86894 Rev. *A
Conditions
–
–
–
–
–
–
–
3.6  VDD
3.0  VDD  3.6
1.71  VDD  3.0
Required to enter programming
mode when coming out of sleep
–
–
–
–
–
–
Min
1
1
40
40
0
–
–
–
–
–
300
Typ
–
–
–
–
–
–
–
–
–
–
–
Max
20
20
–
–
8
18
25
60
85
130
–
Units
ns
ns
ns
ns
MHz
ms
ms
ns
ns
ns
s
300
0.1
14.27
0.01
3.20
–
–
–
–
–
–
1
–
200
19.60
s
ms
ms
ms
ms
98
–
615
s
Page 26 of 54
CY8C24X93
AC I2C Specifications (CY8C24193/493)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 30. AC Characteristics of the I2C SDA and SCL Pins
Symbol
Description
SCL clock frequency
Hold time (repeated) START condition. After this period, the first clock pulse is
generated
tLOW
LOW period of the SCL clock
HIGH Period of the SCL clock
tHIGH
Setup time for a repeated START condition
tSU;STA
tHD;DAT[40] Data hold time
tSU;DAT
Data setup time
Setup time for STOP condition
tSU;STO
Bus free time between a STOP and START condition
tBUF
tSP
Pulse width of spikes are suppressed by the input filter
fSCL
tHD;STA
Standard
Mode
Min
Max
0
100
4.0
–
4.7
4.0
4.7
20
250
4.0
4.7
–
–
–
–
3.45
–
–
–
–
Fast Mode
Min
0
0.6
Max
400
–
1.3
–
0.6
–
0.6
–
20
0.90
100[53]
–
0.6
–
1.3
–
0
50
Units
kHz
µs
µs
µs
µs
µs
ns
µs
µs
ns
Figure 10. Definition for Timing for Fast/Standard Mode on the I2C Bus
Notes
40. To wake up from sleep using I2C hardware address match event, I2C interface needs 20 ns hold time on SDA line with respect to falling edge of SCL. See the
CY8C24x93 Silicon Errata document for more details.
41. A Fast-Mode I2C-bus device can be used in a standard mode I2C-bus system, but the requirement tSU;DAT  250 ns must then be met. This automatically be the
case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 001-86894 Rev. *A
Page 27 of 54
CY8C24X93
Table 31. SPI Master AC Specifications
Min
Typ
Max
Units
FSCLK
Symbol
SCLK clock frequency
Description
VDD 2.4 V
VDD < 2.4 V
Conditions
–
–
–
–
6
3
MHz
MHz
DC
SCLK duty cycle
–
–
50
–
%
tSETUP
MISO to SCLK setup time
VDD  2.4 V
VDD < 2.4 V
60
100
–
–
–
–
ns
ns
tHOLD
SCLK to MISO hold time
–
40
–
–
ns
tOUT_VAL
SCLK to MOSI valid time
–
–
–
40
ns
tOUT_H
MOSI high time
–
40
–
–
ns
Figure 11. SPI Master Mode 0 and 2
SPI Master, modes 0 and 2
1/FSCLK
THIGH
TLOW
SCLK
(mode 0)
SCLK
(mode 2)
TSETUP
MISO
(input)
THOLD
LSB
MSB
TOUT_SU
TOUT_H
MOSI
(output)
Figure 12. SPI Master Mode 1 and 3
SPI Master, modes 1 and 3
1/FSCLK
THIGH
TLOW
SCLK
(mode 1)
SCLK
(mode 3)
TSETUP
MISO
(input)
THOLD
TOUT_SU
MOSI
(output)
Document Number: 001-86894 Rev. *A
LSB
MSB
TOUT_H
MSB
LSB
Page 28 of 54
CY8C24X93
Table 32. SPI Slave AC Specifications
Symbol
FSCLK
tLOW
tHIGH
tSETUP
tHOLD
tSS_MISO
tSCLK_MISO
tSS_HIGH
tSS_CLK
tCLK_SS
Description
SCLK clock frequency
SCLK low time
SCLK high time
MOSI to SCLK setup time
SCLK to MOSI hold time
SS high to MISO valid
SCLK to MISO valid
SS high time
Time from SS low to first SCLK
Time from last SCLK to SS high
Conditions
Min
–
42
42
30
50
–
–
50
2/SCLK
2/SCLK
–
–
–
–
–
–
–
–
–
–
Typ
–
–
–
–
–
–
–
–
–
–
Max
4
–
–
–
–
153
125
–
–
–
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
Figure 13. SPI Slave Mode 0 and 2
SPI Slave, modes 0 and 2
TSS_HIGH
TCLK_SS
TSS_CLK
/SS
1/FSCLK
THIGH
TLOW
SCLK
(mode 0)
SCLK
(mode 2)
TOUT_H
TSS_MISO
MISO
(output)
TSETUP
MOSI
(input)
THOLD
LSB
MSB
Figure 14. SPI Slave Mode 1 and 3
SPI Slave, modes 1 and 3
TSS_CLK
TCLK_SS
/SS
1/FSCLK
THIGH
TLOW
SCLK
(mode 1)
SCLK
(mode 3)
TOUT_H
TSCLK_MISO
TSS_MISO
MISO
(output)
MSB
TSETUP
MOSI
(input)
Document Number: 001-86894 Rev. *A
LSB
THOLD
MSB
LSB
Page 29 of 54
CY8C24X93
Electrical Specifications (CY8C24093/293/393/693)
This section presents the DC and AC electrical specifications of the CY8C24093/293/393/693 PSoC devices. For the latest electrical
specifications, confirm that you have the most recent datasheet by visiting the web at http://www.cypress.com/psoc.
Figure 15. Voltage versus CPU Frequency
5.5V
Vdd Voltage
li d ng
Va rati n
e io
Op Reg
1.71V
750 kHz
3 MHz
CPU
24 MHz
Frequency
Absolute Maximum Ratings (CY8C24093/293/393/693)
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 33. Absolute Maximum Ratings
Conditions
Min
Typ
Max
Units
TSTG
Symbol
Storage temperature
Description
Higher storage temperatures reduce data
retention time. Recommended Storage
Temperature is +25 °C ± 25 °C. Extended
duration storage temperatures above 85 °C
degrades reliability.
–55
+25
+125
°C
VDD
Supply voltage relative to VSS
–
–0.5
–
+6.0
V
VIO
DC input voltage
–
VSS – 0.5
–
VDD + 0.5
V
VIOZ[42]
DC voltage applied to tristate
–
VSS – 0.5
–
VDD + 0.5
V
IMIO
Maximum current into any port pin –
–25
–
+50
mA
ESD
Electrostatic discharge voltage
Human body model ESD
2000
–
–
V
LU
Latch-up current
In accordance with JESD78 standard
–
–
200
mA
Operating Temperature (CY8C24093/293/393/693)
Table 34. Operating Temperature
Min
Typ
Max
Units
TA
Symbol
Ambient temperature
Description
–
Conditions
–40
–
+85
°C
TC
Commercial temperature range
–
0
70
°C
TJ
Operational die temperature
The temperature rise from ambient to
junction is package specific. Refer the
Thermal Impedances on page 48. The user
must limit the power consumption to comply
with this requirement.
+100
°C
–40
–
Note
42. Port1 pins are hot-swap capable with I/O configured in High-Z mode, and pin input voltage above VDD.
Document Number: 001-86894 Rev. *A
Page 30 of 54
CY8C24X93
DC Chip-Level Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 35. DC Chip-Level Specifications
Symbol
VDD
[43, 44, 45]
VDDUSB[43, 44, 45]
Description
Conditions
Min
Typ
Max
Units
Supply voltage
No USB activity. Refer the table DC POR
and LVD Specifications
(CY8C24093/293/393/693) on page 36
1.71
–
5.50
V
Operating voltage
USB activity, USB regulator enabled
4.35
–
5.25
V
USB activity, USB regulator bypassed
3.15
3.3
3.60
V
IDD24
Supply current, IMO = 24 MHz
Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 24 MHz. No I/O sourcing current
–
–
4.00
mA
IDD12
Supply current, IMO = 12 MHz
Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 12 MHz. No I/O sourcing current
–
–
2.60
mA
IDD6
Supply current, IMO = 6 MHz
Conditions are VDD  3.0 V, TA = 25 °C,
CPU = 6 MHz. No I/O sourcing current
–
–
1.80
mA
ISB0
Deep sleep current
VDD  3.0 V, TA = 25 °C, I/O regulator
turned off
–
0.10
1.05
A
ISB1
Standby current with POR, LVD VDD  3.0 V, TA = 25 °C, I/O regulator
and sleep timer
turned off
–
1.07
1.50
A
ISBI2C
Standby current with I2C
enabled
–
1.64
–
A
Conditions are VDD = 3.3 V, TA = 25 °C
and CPU = 24 MHz
Notes
43. When VDD remains in the range from 1.71 V to 1.9 V for more than 50 µs, the slew rate when moving from the 1.71 V to 1.9 V range to greater than 2 V must be
slower than 1 V/500 µs to avoid triggering POR. The only other restriction on slew rates for any other voltage range or transition is the SRPOWER_UP parameter.
44. If powering down in standby sleep mode, to properly detect and recover from a VDD brown out condition any of the following actions must be taken:
a.Bring the device out of sleep before powering down.
b.Assure that VDD falls below 100 mV before powering back up.
c.Set the No Buzz bit in the OSC_CR0 register to keep the voltage monitoring circuit powered during sleep.
d.Increase the buzz rate to assure that the falling edge of VDD is captured. The rate is configured through the PSSDC bits in the SLP_CFG register.
For the referenced registers, refer to the CY8C24x93 Technical Reference Manual. In deep sleep mode, additional low power voltage monitoring circuitry allows
VDD brown out conditions to be detected for edge rates slower than 1V/ms.
45. For USB mode, the VDD supply for bus-powered application should be limited to 4.35 V–5.35 V. For self-powered application, VDD should be 3.15 V–3.45 V.
Document Number: 001-86894 Rev. *A
Page 31 of 54
CY8C24X93
DC GPIO Specifications (CY8C24093/293/393/693)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 C and are for design guidance only.
Table 36. 3.0 V to 5.5 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
RPU
Pull-up resistor
–
4
5.60
8
k
VOH1
High output voltage
Port 2 or 3 or 4 pins
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH2
High output voltage
Port 2 or 3 or 4 pins
IOH = 1 mA, maximum of 20 mA source
current in all I/Os
VDD – 0.90
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH4
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH = 5 mA, maximum of 20 mA source
current in all I/Os
VDD – 0.90
–
–
V
VOH5
High output voltage
IOH < 10 A, VDD > 3.1 V, maximum of 4 I/Os
Port 1 Pins with LDO Regulator Enabled all sourcing 5 mA
for 3 V out
2.85
3.00
3.30
V
VOH6
High output voltage
IOH = 5 mA, VDD > 3.1 V, maximum of 20 mA
Port 1 pins with LDO regulator enabled for source current in all I/Os
3 V out
2.20
–
–
V
VOH7
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
2.35
2.50
2.75
V
VOH8
High output voltage
IOH = 2 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 2.5 V out source current in all I/Os
1.90
–
–
V
VOH9
High output voltage
IOH < 10 A, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.60
1.80
2.10
V
VOH10
High output voltage
IOH = 1 mA, VDD > 2.7 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
IOL = 25 mA, VDD > 3.3 V, maximum of
60 mA sink current on even port pins (for
example, P0[2] and P1[4]) and 60 mA sink
current on odd port pins (for example, P0[3]
and P1[5])
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.80
V
VIH
Input high voltage
–
2.00
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (Absolute Value)
–
–
0.001
1
A
CPIN
Pin capacitance
Package and pin dependent
Temp = 25 °C
0.50
1.70
7
pF
VILLVT3.3
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.8
V
–
–
VIHLVT3.3
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.4
–
–
V
VILLVT5.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.8
V
–
–
VIHLVT5.5
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.7
–
–
V
Document Number: 001-86894 Rev. *A
Page 32 of 54
CY8C24X93
Table 37. 2.4 V to 3.0 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
5.60
8
k
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
High output voltage
Port 2 or 3 or 4 pins
IOH = 0.2 mA, maximum of 10 mA source
current in all I/Os
VDD – 0.40
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for port 1
IOH < 10 A, maximum of 10 mA source
current in all I/Os
VDD – 0.20
–
–
V
VOH4
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source
current in all I/Os
VDD – 0.50
–
–
V
VOH5A
High output voltage
IOH < 10 A, VDD > 2.4 V, maximum of
Port 1 pins with LDO enabled for 1.8 V out 20 mA source current in all I/Os
1.50
1.80
2.10
V
VOH6A
High output voltage
IOH = 1 mA, VDD > 2.4 V, maximum of 20 mA
Port 1 pins with LDO enabled for 1.8 V out source current in all I/Os
1.20
–
–
V
VOL
Low output voltage
–
–
0.75
V
VIL
Input low voltage
–
–
–
0.72
VIH
Input high voltage
–
1.40
–
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
Temp = 25 C
0.50
1.70
7
pF
VILLVT2.5
Input Low Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
0.7
V
–
VIHLVT2.5
Input High Voltage with low threshold
enable set, Enable for Port1
Bit3 of IO_CFG1 set to enable low threshold
voltage of Port1 input
1.2
RPU
Pull-up resistor
–
VOH1
High output voltage
Port 2 or 3 or 4 pins
VOH2
IOL = 10 mA, maximum of 30 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink current on
odd port pins (for example, P0[3] and P1[5])
V
V
–
V
Table 38. 1.71 V to 2.4 V DC GPIO Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
4
RPU
Pull-up resistor
–
5.60
8
k
VOH1
High output voltage
Port 2 or 3 or 4 pins
IOH = 10 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH2
High output voltage
Port 2 or 3 or 4 pins
IOH = 0.5 mA, maximum of 10 mA VDD – 0.50
source current in all I/Os
–
–
V
VOH3
High output voltage
Port 0 or 1 pins with LDO regulator
Disabled for Port 1
IOH = 100 A, maximum of 10 mA VDD – 0.20
source current in all I/Os
–
–
V
VOH4
High output voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA source VDD – 0.50
current in all I/Os
–
–
V
VOL
Low output voltage
IOL = 5 mA, maximum of 20 mA sink
current on even port pins (for example,
P0[2] and P1[4]) and 30 mA sink
current on odd port pins (for example,
P0[3] and P1[5])
–
0.40
V
Document Number: 001-86894 Rev. *A
–
Page 33 of 54
CY8C24X93
Table 38. 1.71 V to 2.4 V DC GPIO Specifications (continued)
Symbol
Description
Conditions
Min
Typ
Max
Units
VIL
Input low voltage
–
–
–
0.30 × VDD
V
VIH
Input high voltage
–
0.65 × VDD
–
–
V
VH
Input hysteresis voltage
–
–
80
–
mV
IIL
Input leakage (absolute value)
–
–
1
1000
nA
CPIN
Capacitive load on pins
Package and pin dependent
temp = 25 °C
0.50
1.70
7
pF
Min
Typ
Max
Units
Table 39. DC Characteristics – USB Interface
Symbol
Description
Conditions
RUSBI
USB D+ pull-up resistance
With idle bus
900
–
1575

RUSBA
USB D+ pull-up resistance
While receiving traffic
1425
–
3090

VOHUSB
Static output high
–
2.8
–
3.6
V
VOLUSB
Static output low
–
–
–
0.3
V
VDI
Differential input sensitivity
–
0.2
–
VCM
Differential input common mode range
–
0.8
–
2.5
V
VSE
Single ended receiver threshold
–
0.8
–
2.0
V
CIN
Transceiver capacitance
–
–
–
50
pF
V
IIO
High Z state data line leakage
On D+ or D- line
–10
–
+10
A
RPS2
PS/2 pull-up resistance
–
3000
5000
7000

REXT
External USB series resistor
In series with each USB pin
21.78
22.0
22.22

DC Analog Mux Bus Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 40. DC Analog Mux Bus Specifications
Symbol
RSW
Description
Conditions
Switch resistance to common analog bus –
RGND
Resistance of initialization switch to VSS
The maximum pin voltage for measuring RSW and RGND is 1.8 V
–
Min
Typ
Max
Units
–
–
800

–
–
800

DC Low Power Comparator Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 41. DC Comparator Specifications
Conditions
Min
Typ
Max
Units
VLPC
Symbol
Low power comparator (LPC) common
mode
Description
Maximum voltage limited to VDD
0.0
–
1.8
V
ILPC
LPC supply current
–
–
10
40
A
VOSLPC
LPC voltage offset
–
–
3
30
mV
Document Number: 001-86894 Rev. *A
Page 34 of 54
CY8C24X93
Comparator User Module Electrical Specifications (CY8C24093/293/393/693)
The following table lists the guaranteed maximum and minimum specifications. Unless stated otherwise, the specifications are for the
entire device voltage and temperature operating range: –40 °C  TA  85 °C, 1.71 V  VDD  5.5 V.
Table 42. Comparator User Module Electrical Specifications
Symbol
Min
Typ
Max
Units
50 mV overdrive
–
70
100
ns
Offset
Valid from 0.2 V to VDD – 0.2 V
–
2.5
30
mV
Current
Average DC current, 50 mV
overdrive
–
20
80
µA
Supply voltage > 2 V
Power supply rejection ratio
–
80
–
dB
Supply voltage < 2 V
Power supply rejection ratio
–
40
–
dB
–
0
1.5
V
tCOMP
PSRR
Description
Comparator response time
Input range
Conditions
ADC Electrical Specifications (CY8C24093/293/393/693)
Table 43. ADC User Module Electrical Specifications
Symbol
Description
Conditions
Min
Typ
Max
Units
0
–
VREFADC
V
–
–
5
pF
Input
VIN
Input voltage range
CIIN
Input capacitance
–
RIN
Input resistance
Equivalent switched cap input
resistance for 8-, 9-, or 10-bit
resolution
ADC reference voltage
–
1.14
–
1.26
V
2.25
–
6
MHz
–
1/(500fF × 1/(400fF × 1/(300fF ×
data clock) data clock) data clock)

Reference
VREFADC
Conversion Rate
FCLK
Data clock
Source is chip’s internal main
oscillator. See AC Chip-Level
Specifications for accuracy
S8
8-bit sample rate
Data clock set to 6 MHz. sample
rate = 0.001/ (2^Resolution/Data
Clock)
–
23.43
–
ksps
S10
10-bit sample rate
Data clock set to 6 MHz. sample
rate = 0.001/ (2^resolution/data
clock)
–
5.85
–
ksps
RES
Resolution
Can be set to 8-, 9-, or 10-bit
8
–
10
bits
DC Accuracy
DNL
Differential nonlinearity
–
–1
–
+2
LSB
INL
Integral nonlinearity
–
–2
–
+2
LSB
EOFFSET
Offset error
8-bit resolution
0
3.20
19.20
LSB
10-bit resolution
0
12.80
76.80
LSB
Gain error
For any resolution
–5
–
+5
%FSR
IADC
Operating current
–
–
2.10
2.60
mA
PSRR
Power supply rejection ratio
PSRR (VDD > 3.0 V)
–
24
–
dB
PSRR (VDD < 3.0 V)
–
30
–
dB
EGAIN
Power
Document Number: 001-86894 Rev. *A
Page 35 of 54
CY8C24X93
DC POR and LVD Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 44. DC POR and LVD Specifications
Symbol
Description
Conditions
Min
VPOR0
1.66 V selected in PSoC Designer
2.36 V selected in PSoC Designer
–
VPOR2
2.60 V selected in PSoC Designer
VDD must be greater than or equal
to 1.71 V during startup, reset
from the XRES pin, or reset from
watchdog.
1.61
VPOR1
–
2.60
2.66
VPOR3
2.82 V selected in PSoC Designer
–
2.82
2.95
VLVD0
2.45 V selected in PSoC Designer
2.40
2.45
2.51
VLVD1
2.71 V selected in PSoC Designer
2.64[46]
2.71
2.78
VLVD2
2.92 V selected in PSoC Designer
2.85[47]
2.92
2.99
VLVD3
3.02 V selected in PSoC Designer
2.95[48]
3.02
3.09
VLVD4
3.13 V selected in PSoC Designer
3.06
3.13
3.20
VLVD5
1.90 V selected in PSoC Designer
1.84
1.90
2.32
VLVD6
1.80 V selected in PSoC Designer
1.75[49]
1.80
1.84
VLVD7
4.73 V selected in PSoC Designer
4.62
4.73
4.83
–
Typ
Max
Units
1.66
1.71
V
2.36
2.41
V
DC Programming Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 45. DC Programming Specifications
Symbol
VDDIWRITE
IDDP
VILP
VIHP
IILP
IIHP
VOLP
VOHP
FlashENPB
FlashDR
Description
Supply voltage for flash write
operations
Supply current during
programming or verify
Input low voltage during
programming or verify
–
Conditions
Min
1.71
Typ
–
Max
5.25
Units
V
–
–
5
25
mA
–
–
VIL
V
VIH
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
VSS + 0.75
V
VOH
–
VDD
V
50,000
20
–
–
–
–
–
Years
See
the
appropriate
DC
GPIO
Specifications (CY8C24093/293/393/693)
on page 32
Input high voltage during
See
the
appropriate
DC
GPIO
programming or verify
Specifications (CY8C24093/293/393/693)
on page 32
Input current when Applying VILP Driving internal pull-down resistor
to P1[0] or P1[1] during
programming or verify
Input current when applying VIHP Driving internal pull-down resistor
to P1[0] or P1[1] during
programming or verify
Output low voltage during
programming or verify
Output high voltage during
See appropriate DC GPIO Specifications
programming or verify
(CY8C24093/293/393/693) on page 32. For
VDD > 3 V use VOH4 in Table 34 on page 30.
Flash write endurance
Erase/write cycles per block
Flash data retention
Following maximum Flash write cycles;
ambient temperature of 55 °C
Notes
46. Always greater than 50 mV above VPPOR1 voltage for falling supply.
47. Always greater than 50 mV above VPPOR2 voltage for falling supply.
48. Always greater than 50 mV above VPPOR3 voltage for falling supply.
49. Always greater than 50 mV above VPPOR0 voltage for falling supply.
Document Number: 001-86894 Rev. *A
Page 36 of 54
CY8C24X93
DC I2C Specifications (CY8C24093/293/393/693)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 46. DC I2C Specifications
Symbol
VILI2C
VIHI2C
Description
Input low level
Input high level
Conditions
3.1 V ≤ VDD ≤ 5.5 V
Min
–
Typ
–
Max
Units
0.25 × VDD
V
2.5 V ≤ VDD ≤ 3.0 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 2.4 V
–
–
0.3 × VDD
V
1.71 V ≤ VDD ≤ 5.5 V
0.65 × VDD
–
–
V
DC Reference Buffer Specifications (CY8C24093/293/393/693)
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 3.0 V to 5.5 V and
–40 °C  TA  85 °C, 2.4 V to 3.0 V and –40 °C  TA  85 °C, or 1.71 V to 2.4 V and –40 °C  TA  85 °C, respectively. Typical
parameters apply to 5 V and 3.3 V at 25 °C and are for design guidance only.
Table 47. DC Reference Buffer Specifications
Symbol
VRef
Description
Reference buffer output
Conditions
1.7 V ≤ VDD ≤ 5.5 V
Min
1
Typ
–
Max
1.05
Units
V
VRefHi
Reference buffer output
1.7 V ≤ VDD ≤ 5.5 V
1.2
–
1.25
V
DC IDAC Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 48. DC IDAC Specifications
Symbol
IDAC_DNL
IDAC_INL
IDAC_Gain
(Source)
Description
Differential nonlinearity
Integral nonlinearity
Range = 0.5x
Range = 1x
Range = 2x
Range = 4x
Range = 8x
Document Number: 001-86894 Rev. *A
Min
–4.5
–5
6.64
14.5
42.7
91.1
184.5
Typ
–
–
–
–
–
–
–
Max
+4.5
+5
22.46
47.8
92.3
170
426.9
Units
Notes
LSB
LSB
µA DAC setting = 128 dec
µA
µA
µA DAC setting = 128 dec
µA DAC setting = 128 dec
Page 37 of 54
CY8C24X93
AC Chip-Level Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 49. AC Chip-Level Specifications
Min
Typ
Max
Units
FIMO24
Symbol
IMO frequency at 24 MHz Setting
–
22.8
24
25.2
MHz
FIMO12
IMO frequency at 12 MHz setting
–
11.4
12
12.6
MHz
FIMO6
IMO frequency at 6 MHz setting
–
5.7
6.0
6.3
MHz
FCPU
CPU frequency
–
0.75
–
25.20
MHz
F32K1
ILO frequency
–
15
32
50
kHz
F32K_U
ILO untrimmed frequency
–
13
32
82
kHz
DCIMO
Duty cycle of IMO
–
40
50
60
%
DCILO
ILO duty cycle
–
40
50
60
%
SRPOWER_UP
Power supply slew rate
VDD slew rate during power-up
–
–
250
V/ms
tXRST
External reset pulse width at power-up After supply voltage is valid
1
–
–
ms
tXRST2
External reset pulse width after
power-up[50]
Applies after part has booted
10
–
–
s
Startup time of ECO
–
–
1
–
s
N=32
6 MHz IMO cycle-to-cycle jitter (RMS)
–
0.7
6.7
ns
6 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
4.3
29.3
ns
6 MHz IMO period jitter (RMS)
–
0.7
3.3
ns
12 MHz IMO cycle-to-cycle jitter (RMS)
–
0.5
5.2
ns
12 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
2.3
5.6
ns
tOS
tJIT_IMO
[51]
Description
Conditions
12 MHz IMO period jitter (RMS)
–
0.4
2.6
ns
24 MHz IMO cycle-to-cycle jitter (RMS)
–
1.0
8.7
ns
24 MHz IMO long term N (N = 32)
cycle-to-cycle jitter (RMS)
–
1.4
6.0
ns
24 MHz IMO period jitter (RMS)
–
0.6
4.0
ns
Notes
50. The minimum required XRES pulse length is longer when programming the device (see Table 55 on page 41).
51. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 001-86894 Rev. *A
Page 38 of 54
CY8C24X93
AC GPIO Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 50. AC GPIO Specifications
Symbol
FGPIO
tRISE23
tRISE23L
tRISE01
tRISE01L
tFALL
tFALLL
Description
GPIO operating frequency
Conditions
Normal strong mode Port 0, 1
Rise time, strong mode, Cload = 50 pF
Port 2 or 3 or 4 pins
Rise time, strong mode low supply,
Cload = 50 pF, Port 2 or 3 or 4 pins
Rise time, strong mode, Cload = 50 pF
Ports 0 or 1
Rise time, strong mode low supply,
Cload = 50 pF, Ports 0 or 1
Fall time, strong mode, Cload = 50 pF
all ports
Fall time, strong mode low supply,
Cload = 50 pF, all ports
Min
0
Typ
–
Max
Units
6 MHz for
MHz
1.71 V <VDD < 2.40 V
MHz
12 MHz for
2.40 V < VDD< 5.50 V
80
ns
0
–
VDD = 3.0 to 3.6 V, 10% to 90%
15
–
VDD = 1.71 to 3.0 V, 10% to 90%
15
–
80
ns
VDD = 3.0 to 3.6 V, 10% to 90%
LDO enabled or disabled
VDD = 1.71 to 3.0 V, 10% to 90%
LDO enabled or disabled
VDD = 3.0 to 3.6 V, 10% to 90%
10
–
50
ns
10
–
80
ns
10
–
50
ns
VDD = 1.71 to 3.0 V, 10% to 90%
10
–
70
ns
Figure 16. GPIO Timing Diagram
90%
GPIO Pin
Output
Voltage
10%
tRISE23
tRISE01
tRISE23L
tRISE01L
Document Number: 001-86894 Rev. *A
tFALL
tFALLL
Page 39 of 54
CY8C24X93
Table 51. AC Characteristics – USB Data Timings
Min
Typ
tDRATE
Symbol
Full speed data rate
Description
Average bit rate
Conditions
12 – 0.25%
12
Max
Units
tJR1
Receiver jitter tolerance
To next transition
–18.5
–
18.5
ns
tJR2
Receiver jitter tolerance
To pair transition
–9.0
–
9
ns
tDJ1
FS Driver jitter
To next transition
–3.5
–
3.5
ns
tDJ2
FS Driver jitter
To pair transition
–4.0
–
4.0
ns
tFDEOP
Source jitter for differential
transition
To SE0 transition
–2.0
–
5
ns
12 + 0.25% MHz
tFEOPT
Source SE0 interval of EOP
–
160.0
–
175
ns
tFEOPR
Receiver SE0 interval of EOP
–
82.0
–
–
ns
tFST
Width of SE0 interval during
differential transition
–
–
–
14
ns
Min
Typ
Max
Units
Table 52. AC Characteristics – USB Driver
Symbol
Description
Conditions
tFR
Transition rise time
50 pF
4
–
20
ns
tFF
Transition fall time
50 pF
4
–
20
ns
tFRFM[52]
Rise/fall time matching
–
90
–
111
%
VCRS
Output signal crossover voltage
–
1.30
–
2.00
V
AC Comparator Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 53. AC Low Power Comparator Specifications
Symbol
tLPC
Description
Comparator response time,
50 mV overdrive
Conditions
50 mV overdrive does not include
offset voltage.
Min
Typ
Max
Units
–
–
100
ns
AC External Clock Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 54. AC External Clock Specifications
Symbol
FOSCEXT
Description
Frequency (external oscillator
frequency)
Conditions
–
Min
Typ
Max
Units
0.75
–
25.20
MHz
High period
–
20.60
–
5300
ns
Low period
–
20.60
–
–
ns
Power-up IMO to switch
–
150
–
–
s
Note
52. TFRFM is not met under all conditions. There is a corner case at lower supply voltages, such as those under 3.3 V. This condition does not affect USB communications.
Signal integrity tests show an excellent eye diagram at 3.15 V.
Document Number: 001-86894 Rev. *A
Page 40 of 54
CY8C24X93
AC Programming Specifications (CY8C24093/293/393/693)
Figure 17. AC Waveform
SCLK (P1[1])
T FSCLK
T RSCLK
SDATA (P1[0])
TSSCLK
T HSCLK
TDSCLK
The following table lists the guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 55. AC Programming Specifications
Symbol
tRSCLK
tFSCLK
tSSCLK
tHSCLK
FSCLK
tERASEB
tWRITE
tDSCLK
tDSCLK3
tDSCLK2
tXRST3
Description
Rise time of SCLK
Fall time of SCLK
Data setup time to falling edge of SCLK
Data hold time from falling edge of SCLK
Frequency of SCLK
Flash erase time (block)
Flash block write time
Data out delay from falling edge of SCLK
Data out delay from falling edge of SCLK
Data out delay from falling edge of SCLK
External reset pulse width after power-up
Conditions
–
–
–
–
–
–
–
3.6  VDD
3.0  VDD  3.6
1.71  VDD  3.0
Required to enter programming
mode when coming out of sleep
tXRES
tVDDWAIT
tVDDXRES
tPOLL
tACQ
XRES pulse length
VDD stable to wait-and-poll hold off
VDD stable to XRES assertion delay
SDATA high pulse time
“Key window” time after a VDD ramp
acquire event, based on 256 ILO clocks.
tXRESINI
“Key window” time after an XRES event,
based on 8 ILO clocks
Document Number: 001-86894 Rev. *A
Min
1
1
40
40
0
–
–
–
–
–
300
Typ
–
–
–
–
–
–
–
–
–
–
–
Max
20
20
–
–
8
18
25
60
85
130
–
Units
ns
ns
ns
ns
MHz
ms
ms
ns
ns
ns
s
–
–
–
–
–
300
0.1
14.27
0.01
3.20
–
–
–
–
–
–
1
–
200
19.60
s
ms
ms
ms
ms
–
98
–
615
s
Page 41 of 54
CY8C24X93
AC I2C Specifications (CY8C24093/293/393/693)
The following table lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 56. AC Characteristics of the I2C SDA and SCL Pins
Symbol
fSCL
tHD;STA
tLOW
tHIGH
tSU;STA
tHD;DAT
tSU;DAT
tSU;STO
tBUF
tSP
Description
SCL clock frequency
Hold time (repeated) START condition. After this period, the first
clock pulse is generated
LOW period of the SCL clock
HIGH Period of the SCL clock
Setup time for a repeated START condition
Data hold time
Data setup time
Setup time for STOP condition
Bus free time between a STOP and START condition
Pulse width of spikes are suppressed by the input filter
Standard Mode
Min
Max
0
100
4.0
–
4.7
4.0
4.7
0
250
4.0
4.7
–
–
–
–
3.45
–
–
–
–
Fast Mode
Min
Max
0
400
0.6
–
1.3
0.6
0.6
0
100[53]
0.6
1.3
0
–
–
–
0.90
–
–
–
50
Units
kHz
µs
µs
µs
µs
µs
ns
µs
µs
ns
Figure 18. Definition for Timing for Fast/Standard Mode on the I2C Bus
Note
53. A Fast-Mode I2C-bus device can be used in a standard mode I2C-bus system, but the requirement tSU;DAT  250 ns must then be met. This automatically be the
case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit
to the SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 001-86894 Rev. *A
Page 42 of 54
CY8C24X93
Table 57. SPI Master AC Specifications
Min
Typ
Max
Units
FSCLK
Symbol
SCLK clock frequency
Description
VDD 2.4 V
VDD < 2.4 V
Conditions
–
–
–
–
6
3
MHz
MHz
DC
SCLK duty cycle
–
–
50
–
%
tSETUP
MISO to SCLK setup time
VDD  2.4 V
VDD < 2.4 V
60
100
–
–
–
–
ns
ns
tHOLD
SCLK to MISO hold time
–
40
–
–
ns
tOUT_VAL
SCLK to MOSI valid time
–
–
–
40
ns
tOUT_H
MOSI high time
–
40
–
–
ns
Figure 19. SPI Master Mode 0 and 2
SPI Master, modes 0 and 2
1/FSCLK
THIGH
TLOW
SCLK
(mode 0)
SCLK
(mode 2)
TSETUP
MISO
(input)
THOLD
LSB
MSB
TOUT_SU
TOUT_H
MOSI
(output)
Figure 20. SPI Master Mode 1 and 3
SPI Master, modes 1 and 3
1/FSCLK
THIGH
TLOW
SCLK
(mode 1)
SCLK
(mode 3)
TSETUP
MISO
(input)
THOLD
TOUT_SU
MOSI
(output)
Document Number: 001-86894 Rev. *A
LSB
MSB
TOUT_H
MSB
LSB
Page 43 of 54
CY8C24X93
Table 58. SPI Slave AC Specifications
Symbol
FSCLK
tLOW
tHIGH
tSETUP
tHOLD
tSS_MISO
tSCLK_MISO
tSS_HIGH
tSS_CLK
tCLK_SS
Description
SCLK clock frequency
SCLK low time
SCLK high time
MOSI to SCLK setup time
SCLK to MOSI hold time
SS high to MISO valid
SCLK to MISO valid
SS high time
Time from SS low to first SCLK
Time from last SCLK to SS high
Conditions
Min
–
42
42
30
50
–
–
50
2/SCLK
2/SCLK
–
–
–
–
–
–
–
–
–
–
Typ
–
–
–
–
–
–
–
–
–
–
Max
4
–
–
–
–
153
125
–
–
–
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
Figure 21. SPI Slave Mode 0 and 2
SPI Slave, modes 0 and 2
TCLK_SS
TSS_CLK
TSS_HIGH
/SS
1/FSCLK
THIGH
TLOW
SCLK
(mode 0)
SCLK
(mode 2)
TOUT_H
TSS_MISO
MISO
(output)
TSETUP
MOSI
(input)
THOLD
LSB
MSB
Figure 22. SPI Slave Mode 1 and 3
SPI Slave, modes 1 and 3
TSS_CLK
TCLK_SS
/SS
1/FSCLK
THIGH
TLOW
SCLK
(mode 1)
SCLK
(mode 3)
TOUT_H
TSCLK_MISO
TSS_MISO
MISO
(output)
MSB
TSETUP
MOSI
(input)
Document Number: 001-86894 Rev. *A
LSB
THOLD
MSB
LSB
Page 44 of 54
CY8C24X93
Packaging Information
This section illustrates the packaging specifications for the CY8C24X93 PSoC device, along with the thermal impedances for each
package.
Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of
the emulation tools’ dimensions, refer to the document titled PSoC Emulator Pod Dimensions at
http://www.cypress.com/design/MR10161.
Figure 23. 32-pin QFN (5 × 5 × 0.55 mm) LQ32 3.5 × 3.5 E-Pad (Sawn) Package Outline, 001-42168
001-42168 *E
Document Number: 001-86894 Rev. *A
Page 45 of 54
CY8C24X93
Figure 24. 16-pin Chip On Lead (3 × 3 × 0.6 mm) LG16A/LD16A (Sawn) Package Outline, 001-09116
001-09116 *H
Figure 25. 48-pin QFN (6 × 6 × 0.6 mm) LQ48A 4.6 × 4.6 E-Pad (Sawn) Package Outline, 001-57280
001-57280 *E
Document Number: 001-86894 Rev. *A
Page 46 of 54
CY8C24X93
Figure 26. 48-pin QFN (7 × 7 × 1.0 mm) LT48A 5.1 × 5.1 E-Pad (SAWN) Package Outline, 001-13191
001-13191 *G
Important Notes
For information on the preferred dimensions for mounting QFN packages, see the following Application Note at
http://www.amkor.com/products/notes_papers/MLFAppNote.pdf.
■ Pinned vias for thermal conduction are not required for the low power PSoC device.
■
Document Number: 001-86894 Rev. *A
Page 47 of 54
CY8C24X93
Thermal Impedances
Table 59. Thermal Impedances per Package
Typical JA [54]
Typical JC
16-pin QFN (No Center Pad)
33 C/W
–
32-pin QFN [55]
20 C/W
–
25.20 C/W
3.04 C/W
18 C/W
–
Package
48-pin QFN (6 × 6 × 0.6 mm)
[55]
48-pin QFN (7 × 7 × 1.0 mm) [55]
Capacitance on Crystal Pins
Table 60. Typical Package Capacitance on Crystal Pins
Package
Package Capacitance
32-pin QFN
3.2 pF
48-pin QFN
3.3 pF
Solder Reflow Specifications
Table 61 shows the solder reflow temperature limits that must not be exceeded.
Table 61. Solder Reflow Specifications
Maximum Peak Temperature (TC)
Maximum Time above TC – 5 °C
16-pin QFN
Package
260 C
30 seconds
32-pin QFN
260 C
30 seconds
48-pin QFN (6 × 6 × 0.6 mm)
260 C
30 seconds
48-pin QFN (7 × 7 × 1.0 mm)
260 C
30 seconds
Notes
54. TJ = TA + Power × JA.
55. To achieve the thermal impedance specified for the QFN package, the center thermal pad must be soldered to the PCB ground plane.
Document Number: 001-86894 Rev. *A
Page 48 of 54
CY8C24X93
Development Tool Selection
Software
PSoC Designer™
At the core of the PSoC development software suite is PSoC
Designer. Utilized by thousands of PSoC developers, this robust
software has been facilitating PSoC designs for over half a
decade. PSoC Designer is available free of charge at
http://www.cypress.com.
■
Cat-5 Adapter
■
Mini-Eval Programming Board
■
110 ~ 240 V Power Supply, Euro-Plug Adapter
■
iMAGEcraft C Compiler (Registration Required)
■
ISSP Cable
■
USB 2.0 Cable and Blue Cat-5 Cable
■
2 CY8C29466A-24PXI 28-PDIP Chip Samples
PSoC Programmer
Evaluation Tools
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can operate
directly from PSoC Designer. PSoC Programmer software is
compatible with both PSoC ICE-Cube In-Circuit Emulator and
PSoC MiniProg. PSoC Programmer is available free of charge
at http://www.cypress.com.
All evaluation tools are sold at the Cypress Online Store.
Development Kits
CY3210-PSoCEval1
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, and plenty of
breadboarding space to meet all of your evaluation needs. The
kit includes:
All development kits are sold at the Cypress Online Store.
■
Evaluation Board with LCD Module
CY3215-DK Basic Development Kit
■
MiniProg Programming Unit
■
28-Pin CY8C29466A-24PXI PDIP PSoC Device Sample (2)
■
PSoC Designer Software CD
■
Getting Started Guide
■
USB 2.0 Cable
The CY3215-DK is for prototyping and development with PSoC
Designer. This kit supports in-circuit emulation and the software
interface enables users to run, halt, and single step the
processor and view the content of specific memory locations.
PSoC Designer supports the advance emulation features also.
The kit includes:
■
PSoC Designer Software CD
Device Programmers
■
ICE-Cube In-Circuit Emulator
■
ICE Flex-Pod for CY8C29X66A Family
All device programmers are purchased from the Cypress Online
Store.
Document Number: 001-86894 Rev. *A
Page 49 of 54
CY8C24X93
Ordering Information
The following table lists the CY8C24X93 PSoC devices' key package features and ordering codes.
Table 62. PSoC Device Key Features and Ordering Information
Package
Flash
(Bytes)
Ordering Code
SRAM Digital
Analog XRES USB
(Bytes) I/O Pins Inputs [56] Pin
ADC Supported
by OCD
16-pin QFN
(3 × 3 × 0.6 mm)
CY8C24093-24LKXI
8K
1K
13
13
Yes
No
Yes
No
32-pin QFN
(5 × 5 × 0.6 mm)
CY8C24193-24LQXI
8K
1K
28
28
Yes
No
Yes
Yes
32-pin QFN
(5 × 5 × 0.6 mm)
CY8C24293-24LQXI
16 K
2K
28
28
Yes
No
Yes
No
48-pin QFN
(6 × 6 × 0.6 mm)
CY8C24393-24LQXI
16 K
2K
34
34
Yes
No
Yes
No
48-pin QFN
(7 × 7 × 1.0 mm)
CY8C24493-24LTXI
32 K
2K
36
36
Yes
Yes
Yes
Yes
48-pin QFN
(6 × 6 × 0.6 mm)
CY8C24693-24LQXI
32 K
2K
34
34
Yes
No
Yes
No
32 K
2K
36
36
Yes
Yes
Yes
–
48-pin QFN (OCD) CY8C240093-24LTXI
(7 × 7 × 1.0 mm)
Ordering Code Definitions
CY
8
C
24
X93
- 24
XX
X
I
X
X = blank or T
blank = Tube; T = Tape and Reel
Temperature range:
I = Industrial
Pb-free
Package Type:
LK = 16-pin QFN; LQ = 32-pin QFN or 48-pin QFN
Speed Grade: 24 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = PSoC
Company ID: CY = Cypress
Note
56. Dual-function Digital I/O Pins also connect to the common analog mux.
Document Number: 001-86894 Rev. *A
Page 50 of 54
CY8C24X93
Acronyms
Reference Documents
Table 63. Acronyms Used in this Document
Acronym
Description
AC
alternating current
ADC
analog-to-digital converter
API
application programming interface
CMOS
complementary metal oxide semiconductor
CPU
central processing unit
DAC
digital-to-analog converter
DC
direct current
EOP
end of packet
FSR
full scale range
GPIO
general purpose input/output
GUI
graphical user interface
I 2C
inter-integrated circuit
ICE
in-circuit emulator
IDAC
digital analog converter current
ILO
internal low speed oscillator
IMO
internal main oscillator
I/O
input/output
ISSP
in-system serial programming
LCD
liquid crystal display
LDO
low dropout (regulator)
LSB
least-significant bit
LVD
low voltage detect
MCU
micro-controller unit
MIPS
mega instructions per second
MISO
master in slave out
MOSI
master out slave in
MSB
most-significant bit
OCD
on-chip debugger
POR
power on reset
PPOR
precision power on reset
PSRR
power supply rejection ratio
PWRSYS power system
PSoC®
Programmable System-on-Chip
SLIMO
slow internal main oscillator
SRAM
static random access memory
SNR
signal to noise ratio
QFN
quad flat no-lead
SCL
serial I2C clock
SDA
serial I2C data
SDATA
serial ISSP data
SPI
serial peripheral interface
SS
slave select
SSOP
shrink small outline package
TC
test controller
USB
universal serial bus
USB D+
USB Data+
USB D–
USB Data–
WLCSP
wafer level chip scale package
XTAL
crystal
■
Technical reference manual for CY8C24x93 devices
■
In-system Serial Programming (ISSP) protocol for CY8C24x93
(AN2026C)
■
Host Sourced Serial Programming for CY8C24x93 devices
(AN59389)
Document Number: 001-86894 Rev. *A
Document Conventions
Units of Measure
Table 64. Units of Measure
Symbol
°C
dB
fF
g
Hz
KB
Kbit
KHz
Ksps
k
MHz
M
A
F
H
s
W
mA
ms
mV
nA
nF
ns
nV
W
pA
pF
pp
ppm
ps
sps
s
V
W
Unit of Measure
degree Celsius
decibels
femtofarad
gram
hertz
1024 bytes
1024 bits
kilohertz
kilo samples per second
kilohm
megahertz
megaohm
microampere
microfarad
microhenry
microsecond
microwatt
milliampere
millisecond
millivolt
nanoampere
nanofarad
nanosecond
nanovolt
ohm
picoampere
picofarad
peak-to-peak
parts per million
picosecond
samples per second
sigma: one standard deviation
volt
watt
Page 51 of 54
CY8C24X93
Numeric Naming
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’, ‘b’, or 0x are decimal.
Glossary
Crosspoint connection
Connection between any GPIO combination via analog multiplexer bus.
Differential non-linearity
Ideally, any two adjacent digital codes correspond to output analog voltages that are exactly
one LSB apart. Differential non-linearity is a measure of the worst case deviation from the
ideal 1 LSB step.
Hold time
Hold time is the time following a clock event during which the data input to a latch or flip-flop
must remain stable in order to guarantee that the latched data is correct.
I2C
It is a serial multi-master bus used to connect low speed peripherals to MCU.
Integral nonlinearity
It is a term describing the maximum deviation between the ideal output of a DAC/ADC and
the actual output level.
Latch-up current
Current at which the latch-up test is conducted according to JESD78 standard (at 125
degree Celsius)
Power supply rejection ratio (PSRR)
The PSRR is defined as the ratio of the change in supply voltage to the corresponding
change in output voltage of the device.
Setup time
Period required to prepare a device, machine, process, or system for it to be ready to
function.
SPI
Serial peripheral interface is a synchronous serial data link standard.
Document Number: 001-86894 Rev. *A
Page 52 of 54
CY8C24X93
Document History Page
Document Title: CY8C24X93, PSoC® Programmable System-on-Chip
Document Number: 001-86894
Orig. of
Submission
Revision
ECN
Description of Change
Change
Date
3947416
AMKA
04/02/2013 New data sheet.
**
3971208
AMKA
04/30/2013 Changed status from Preliminary to Final.
*A
Updated Features.
Updated PSoC® Functional Overview (Updated Analog system (Updated
IDAC), updated Additional System Resources).
Updated Ordering Information (Updated part numbers).
Document Number: 001-86894 Rev. *A
Page 53 of 54
CY8C24X93
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
cypress.com/go/automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
cypress.com/go/memory
Optical & Image Sensing
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
cypress.com/go/USB
Wireless/RF
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-86894 Rev. *A
®
Revised April 30, 2013
®
Page 54 of 54
PSoC Designer™ is a trademark and PSoC and CapSense are registered trademarks of Cypress Semiconductor Corporation.
Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
that the system conforms to the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors.
All products and company names mentioned in this document may be the trademarks of their respective holders.