http://www.ti.com/lit/ds/symlink/vca810.pdf

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
VCA810 High Gain Adjust Range, Wideband and Variable Gain Amplifier
1 Features
•
•
•
•
•
•
•
•
•
1
Operating from ±5-V supplies, the device gain control
voltage adjusts the gain from –40 dB at a 0-V input to
40 dB at a –2-V input. Increasing the control voltage
above ground attenuates the signal path to greater
than 80 dB. Signal bandwidth and slew rate remain
constant over the entire gain adjust range. This 40dB/V gain control is accurate within ±1.5 dB (±0.9 dB
for high grade), allowing the gain control voltage in an
AGC application to be used as a received signal
strength indicator (RSSI) with ±1.5-dB accuracy.
High Gain Adjust Range: ±40 dB
Differential In, Single-Ended Out
Low Input Noise Voltage: 2.4 nV/√Hz
Constant Bandwidth vs Gain: 35 MHz
High dB/V Gain Linearity: ±0.3 dB
Gain Control Bandwidth: 25 MHz
Low Output DC Error: < ±40 mV
High Output Current: ±60 mA
Low Supply Current: 24.8 mA
(Maximum for –40°C to 85°C Temperature Range)
Excellent common-mode rejection and commonmode input range at the two high-impedance inputs
allow the device to provide a differential receiver
operation with gain adjust. The output signal is
referenced to ground. Zero differential input voltage
gives a 0-V output with a small DC offset error. Low
input noise voltage ensures good output SNR at the
highest gain settings.
2 Applications
•
•
•
•
•
•
•
Optical Receiver Time Gain Control
Sonar Systems
Voltage-Tunable Active Filters
Log Amplifiers
Pulse Amplitude Compensation
AGC receivers With RSSI
Improved Replacement for VCA610
In applications where pulse edge information is
critical, and the device is being used to equalize
varying channel loss, minimal change in group delay
over gain setting retains excellent pulse edge
information.
An improved output stage provides adequate output
current to drive the most demanding loads. Although
principally intended to drive analog-to-digital
converters (ADCs) or second-stage amplifiers, the
±60-mA output current easily drives doublyterminated 50-Ω lines or a passive post-filter stage
over the ±1.7-V output voltage range.
3 Description
The VCA810 is a DC-coupled, wideband,
continuously
variable,
voltage-controlled
gain
amplifier. The device provides a differential input to
single-ended output conversion with a highimpedance gain control input used to vary the gain
over a –40-dB to 40-dB range linear in dB/V.
Device Information
PART NUMBER
VCA810
PACKAGE
SOIC (8)
BODY SIZE (NOM)
4.90 mm × 3.91 mm
Functional Block Diagram
+5V
6
V+
V-
VCA810
1
8
Gain
Adjust
+
X1
5
VOUT
2
VC
3
0 ® -2V
-40dB ® +40dB Gain
7
-5V
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
Absolute Maximum Ratings ..................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 4
Electrical Characteristics........................................... 5
High Grade DC Characteristics: VS = ±5 V
(VCA810AID) ............................................................. 9
7.7 Typical Characteristics ............................................ 11
8
Detailed Description ............................................ 16
8.1 Overview ................................................................. 16
8.2 Functional Block Diagram ....................................... 16
8.3 Feature Description................................................. 16
8.4 Device Functional Modes........................................ 20
9
Applications and Implementation ...................... 21
9.1 Application Information............................................ 21
9.2 Typical Application .................................................. 30
10 Power Supply Recommendations ..................... 31
11 Layout................................................................... 31
11.1 Layout Guidelines ................................................. 31
11.2 Layout Example .................................................... 32
12 Device and Documentation Support ................. 33
12.1
12.2
12.3
12.4
12.5
12.6
Device Support......................................................
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
33
33
33
33
33
33
13 Mechanical, Packaging, and Orderable
Information ........................................................... 33
4 Revision History
Changes from Revision F (December 2010) to Revision G
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................. 1
•
Changed DC Performance, Input offset current parameter unit from mA to nA in High Grade DC Characteristics table ..... 9
Changes from Revision E (August 2008) to Revision F
Page
•
Deleted lead temperature specification from Absolute Maximum Ratings table ................................................................... 4
•
Corrected typo in Figure 34 .................................................................................................................................................. 21
Changes from Revision D (February, 2006) to Revision E
•
2
Page
Changed storage temperature minimum value in Absolute Maximum Ratings table from –40°C to –65°C .......................... 4
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
5 Device Comparison Table
SINGLES
DUALS
GAIN ADJUST RANGE (dB)
INPUT NOISE (nV/√Hz)
SIGNAL BANDWIDTH (MHz)
VCA811
—
80
2.4
80
—
VCA2612
45
1.25
80
—
VCA2613
45
1
80
—
VCA2614
45
3.6
40
—
VCA2616
45
3.3
40
—
VCA2618
45
5.5
30
6 Pin Configuration and Functions
D Package
8-Pin SOIC
Top View
A
-In
-VS
8
7
+VS VOUT
6
5
(1)
VCA810
1
+In
(1)
High grade version indicator.
(2)
NC = Not connected.
2
3
4
GND Gain NC
Control,
VC
(2)
Pin Functions
PIN
NO.
1
NAME
I/O
DESCRIPTION
+In
I
Noninverting input
2
GND
P
Ground, serves as reference for gain control pin
3
Gain Control,
VC
I
Gain control
4
NC
—
No connect
5
VOUT
O
Output
6
+VS
P
Positive supply
7
–VS
P
Negative supply
8
–In
I
Inverting input
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
3
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
Over operating free-air temperature range, unless otherwise noted. (1)
MIN
Power supply
Internal power dissipation
MAX
UNIT
±6.5
V
See Thermal Information
Differential input voltage
±VS
V
Input common-mode voltage
±VS
V
150
°C
125
°C
Junction temperature, TJ
Storage temperature, Tstg
(1)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±1500
Machine Model (MM)
±200
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Temperature
Supply voltage
MIN
NOM
MAX
–40
25
85
UNIT
°C
±4
±5
±5.5
V
7.4 Thermal Information
VCA810
THERMAL METRIC
(1)
D (SOIC)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
80
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
51
°C/W
RθJB
Junction-to-board thermal resistance
45
°C/W
ψJT
Junction-to-top characterization parameter
14
°C/W
ψJB
Junction-to-board characterization parameter
45
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
7.5 Electrical Characteristics
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AC PERFORMANCE
TJ = 25°C
Small-signal bandwidth (see
Functional Block Diagram)
35
TJ = 25°C (2)
−2 V ≤ VC ≤ 0 V
30
MHz
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
B
(3)
29
29
TJ = 25°C
Large-signal bandwidth
35
TJ = 25°C (2)
VO = 2 VPP, −2 ≤ VC ≤ −1
30
B
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
MHz
29
(3)
29
TJ = 25°C
Frequency response peaking
VO < 500 mVPP, −2 V ≤ VC ≤ 0 V
0.1
TJ = 25°C (2)
0.5
B
TJ = 0°C to 70°C (3)
dB
0.5
TJ = –40°C to 85°C (3)
0.5
TJ = 25°C
Slew rate
VO = 3.5-V step, −2 ≤ VC ≤ −1,
10% to 90%
350
TJ = 25°C (2)
300
B
TJ = 0°C to 70°C (3)
V/μs
300
TJ = –40°C to 85°C (3)
295
TJ = 25°C
Settling time to 0.01%
VO = 1-V step, −2 ≤ VC ≤ −1
30
TJ = 25°C (2)
40
B
TJ = 0°C to 70°C (3)
ns
41
TJ = –40°C to 85°C (3)
41
TJ = 25°C
Rise-and-fall time
VO = 1-V step, −2 ≤ VC ≤ −1
10
TJ = 25°C (2)
12
B
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
ns
12.1
(3)
12.1
Group delay
G = 0 dB, VC= −1 V, f = 5 MHz,
VO = 500 mVPP
TJ = 25°C
C
6.2
ns
Group delay variation
VO < 500 mVPP, −2 V ≤ VC ≤ 0 V,
f = 5 MHz
TJ = 25°C
C
3.5
ns
Second harmonic distortion
VO = 1 VPP, f = 1 MHz,
VC = −1 V, G = 0 dB
TJ = 25°C
HD2
–71
TJ = 25°C (2)
–51
B
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
dBc
–50
(3)
–49
−35
TJ = 25°C
HD3
Third harmonic distortion
TJ = 25°C (2)
VO = 1 VPP, f = 1 MHz,
VC = −1 V, G = 0 dB
TJ = 0°C to 70°C (3)
–34
B
dBc
–32
TJ = –40°C to 85°C (3)
–29
TJ = 25°C
Input voltage noise
TJ = 25°C (2)
VC = −2 V
TJ = 0°C to 70°C (3)
2.4
2.8
B
nV/√Hz
3.4
TJ = –40°C to 85°C (3)
3.5
TJ = 25°C
Input current noise
TJ = 25°C (2)
−2 V ≤ VC ≤ 0 V
TJ = 0°C to 70°C (3)
1.4
1.8
B
pA/√Hz
2
TJ = –40°C to 85°C (3)
(1)
(2)
(3)
TJ = 25°C
Fully attenuated feedthrough
f ≤ 1 MHz, VC > 200 mV
Overdrive recovery
VIN = 2 V to 0 V, VC = −2 V,
G = 40 dB
TJ = 25°C (2)
TJ = 25°C
TJ = 25°C (2)
2.1
−80
B
−70
dB
100
B
ns
150
Test levels: (A) 100% tested at 25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value; only for information.
Junction temperature = ambient for 25°C tested specifications.
Junction temperature = ambient at low temperature limit; junction temperature = ambient 30°C at high temperature limit for over
temperature specifications.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
5
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Electrical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC PERFORMANCE (Single-Ended or Differential Input)
TJ = 25°C
Output offset voltage (both
inputs grounded) (4)
−2 V ≤ VC ≤ 0 V
±22
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
Output offset voltage drift
±4
TJ = 25°C (2)
mV
±30
(3)
TJ = 0°C to 70°C (3)
±32
±125
B
TJ = –40°C to 85°C (3)
V/°C
±125
TJ = 25°C
Input offset voltage (4)
±0.1
TJ = 25°C (2)
Both inputs grounded
±0.25
A
TJ = 0°C to 70°C (3)
mV
±0.3
TJ = –40°C to 85°C (3)
input offset voltage drift
TJ = 0°C to 70°C (3)
±0.35
±1
B
TJ = –40°C to 85°C (3)
−6
TJ = 25°C
Input bias current
TJ = 25°C (2)
−2 V ≤ VC ≤ 0 V
–10
A
TJ = 0°C to 70°C (3)
−12
TJ = –40°C to 85°C (3)
Input bias current drift
TJ = 0°C to 70°C (3)
±25
B
TJ = –40°C to 85°C (3)
nA/°C
±30
±100
TJ = 25°C (2)
−2 V ≤ VC ≤ 0 V
±600
A
TJ = 0°C to 70°C (3)
nA
±700
TJ = –40°C to 85°C (3)
Input offset current drift
μA
−14
TJ = 25°C
Input offset current
μV/°C
±1.2
TJ = 0°C to 70°C (3)
±800
±1.4
B
TJ = –40°C to 85°C (3)
nA/°C
±2.2
INPUT
TJ = 25°C
Common-mode input range
±2.4
TJ = 25°C (2)
±2.3
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
V
±2.3
(3)
±2.2
TJ = 25°C
Common-mode rejection ratio
VCM = 0.5 V, VC = −2 V, inputreferred
Differential input range (5)
85
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
Input impedance
95
TJ = 25°C (2)
dB
83
(3)
80
VCM = 0 V, single-ended
TJ = 25°C
C
1 || 1
MΩ || pF
VCM = 0 V, differential
TJ = 25°C
C
> 10 || < 2
MΩ || pF
VC = 0 V, VCM = 0 V
TJ = 25°C
C
3
VPP
OUTPUT
TJ = 25°C
VC = −2 V, RL = 100 Ω
±1.8
TJ = 25°C (2)
±1.7
A
TJ = 0°C to 70°C (3)
V
±1.4
TJ = –40°C to 85°C (3)
Voltage output swing
±1.3
TJ = 25°C
VC = −2 V, RL = 100 Ω
±1.7
TJ = 25°C (2)
±1.6
A
TJ = 0°C to 70°C (3)
V
±1.3
TJ = –40°C to 85°C (3)
±1.2
TJ = 25°C
Output current
VO = 0 V
6
±40
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
(4)
(5)
±60
TJ = 25°C (2)
mA
±35
(3)
±32
Output short-circuit current
VO = 0 V
TJ = 25°C
C
±120
Output impedance
VO = 0 V, f < 100 kHz
TJ = 25°C
C
0.2
mA
Ω
Total output offset is: (Output Offset Voltage ± Input Offset Voltage x Gain).
Maximum input at minimum gain for < 1-dB gain compression.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Electrical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GAIN CONTROL (VC, Pin 3, Single-Ended or Differential Input)
Specified gain range
ΔVC / ΔdB = 25 mV/dB
TJ = 25°C
C
±40
dB
Maximum control voltage
G = −40 dB
TJ = 25°C
C
0
V
Minimum control voltage
G = 40 dB
TJ = 25°C
C
–2
V
TJ = 25°C
±0.4
TJ = 25°C (2)
−1.8 V ≤ VC ≤ −0.2 V
±1.5
A
TJ = 0°C to 70°C (3)
dB
±2.5
TJ = –40°C to 85°C (3)
Gain accuracy
±3.5
TJ = 25°C
±0.5
TJ = 25°C (2)
VC < −1.8 V, VC > −0.2 V
±2.2
A
TJ = 0°C to 70°C (3)
dB
±3.7
TJ = –40°C to 85°C (3)
TJ = 0°C to 70°C (3)
−1.8 V ≤ VC ≤ −0.2 V
TJ = –40°C to 85°C (3)
Gain drift
TJ = 0°C to 70°C
VC < −1.8 V, VC > −0.2 V
Gain control slope
±4.7
±0.02
B
dB/°C
±0.03
(3)
±0.03
TJ = –40°C to 85°C (3)
25°C
B
dB/°C
±0.04
C
–40
TJ = 25°C
TJ = 25°C (2)
−1.8 V ≤ VC ≤ 0 V
±1
A
TJ = 0°C to 70°C (3)
dB
±1.1
TJ = –40°C to 85°C (3)
Gain control linearity (6)
±1.2
TJ = 25°C
±0.7
TJ = 25°C (2)
VC < −1.8 V
±1.6
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
dB
±2.5
(3)
±3.2
TJ = 25°C
Gain control bandwidth
25
TJ = 25°C (2)
20
B
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
dB/V
±0.3
MHz
19
(3)
19
Gain control slew rate
80-dB gain step
TJ = 25°C
C
900
dB/ns
Gain settling time
1%, 80-dB step
TJ = 25°C
C
0.8
μs
TJ = 25°C
Input bias current
–1.5
TJ = 25°C (2)
VC = −1 V
–3.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
–8
TJ = 25°C
Gain + power-supply rejection
ratio
VC = −2 V, G = 40 dB, +VS = 5 V
± 0.5 V
0.5
TJ = 25°C (2)
1.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
dB/V
1.8
(3)
2
TJ = 25°C
Gain – power-supply rejection
ratio
VC = −2 V, G = 40 dB,
–VS = –5 V ± 0.5 V
μA
–4.5
(3)
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
0.7
1.5
A
dB/V
1.8
TJ = –40°C to 85°C (3)
2
POWER SUPPLY
Specified operating voltage
TJ = 25°C (2)
C
TJ = 25°C (2)
Minimum operating voltage
TJ = 0°C to 70°C (3)
A
TJ = –40°C to 85°C (3)
±4
V
±6
TJ = 0°C to 70°C (3)
A
TJ = –40°C to 85°C (3)
(6)
V
±4
TJ =25°C (2)
Maximum operating voltage
±5
±4
±6
V
±6
Maximum deviation from best line fit.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
7
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Electrical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TJ = 25°C
+VS = 5 V, G = −40 dB
mA
12.6
(3)
12.7
18
TJ = 25°C (2)
20.5
A
TJ = 0°C to 70°C (3)
mA
22
TJ = –40°C to 85°C (3)
22.3
TJ = 25°C
+VS = 5 V, G = –40 dB
10
TJ = 25°C (2)
7.5
A
TJ = 0°C to 70°C (3)
mA
7.2
TJ = –40°C to 85°C (3)
Positive minimum supply
quiescent current
7.1
TJ = 25°C
+VS = 5 V, G = 40 dB
18
TJ = 25°C (2)
15.5
A
TJ = 0°C to 70°C (3)
mA
14.5
TJ = –40°C to 85°C (3)
13.5
TJ = 25°C
−VS = −5 V, G = −40 dB
12
TJ = 25°C (2)
14.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
Negative maximum supply
quiescent current (7)
mA
14.6
(3)
14.7
TJ = 25°C
−VS = −5 V, G = 40 dB
20
TJ = 25°C (2)
22.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
mA
24.5
(3)
24.8
TJ = 25°C
−VS = −5 V, G = −40 dB
12
TJ = 25°C (2)
9.5
A
TJ = 0°C to 70°C (3)
mA
9.4
TJ = –40°C to 85°C (3)
Negative minimum supply
quiescent current (7)
9.3
TJ = 25°C
−VS = −5 V, G = 40 dB
20
TJ = 25°C (2)
17.5
A
TJ = 0°C to 70°C (3)
mA
16.5
TJ = –40°C to 85°C (3)
16
TJ = 25°C
+PSRR
Positive power-supply rejection
ratio
Input-referred, VC = −2 V
90
TJ = 25°C (2)
75
A
TJ = 0°C to 70°C (3)
dB
75
TJ = –40°C to 85°C (3)
73
TJ = 25°C
–PSRR
Negative power-supply
rejection ratio
Input-referred, VC = −2 V
85
TJ = 25°C (2)
70
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
UNIT
12.5
A
TJ = 0°C to 70°C (3)
TJ = 25°C
+VS = 5 V, G = 40 dB
MAX
10
TJ = 25°C (2)
TJ = –40°C to 85°C
Positive maximum supply
quiescent current
TYP
dB
70
(3)
68
THERMAL CHARACTERISTICS
Specified operating range, ID
package
(7)
8
C
–40
85
°C
Magnitude.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
7.6 High Grade DC Characteristics: VS = ±5 V (VCA810AID)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC PERFORMANCE (Single-Ended or Differential Input)
TJ = 25°C
Output offset voltage
±4
TJ = 25°C (2)
−2 V < VC < 0 V
±14
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
mV
±24
(3)
±26
TJ = 25°C
Input offset voltage
±0.1
TJ = 25°C (2)
±0.2
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
mV
±0.25
(3)
±0.3
TJ = 25°C
Input offset current
±100
TJ = 25°C (2)
±500
A
TJ = 0°C to 70°C (3)
nA
±600
TJ = –40°C to 85°C (3)
±700
GAIN CONTROL (VC, Pin 3, Single-Ended or Differential Input)
TJ = 25°C
−1.8 V ≤ VC ≤ −0.2 V
±0.4
TJ = 25°C (2)
±0.9
A
TJ = 0°C to 70°C (3)
dB
±1.9
TJ = –40°C to 85°C (3)
Gain accuracy
±2.9
TJ = 25°C
VC < −1.8 V, VC > −0.2 V
±0.5
TJ = 25°C (2)
±1.5
A
TJ = 0°C to 70°C (3)
dB
±3.0
TJ = –40°C to 85°C (3)
±4.0
TJ = 25°C
−1.8 V ≤ VC ≤ 0 V
±0.3
TJ = 25°C (2)
±0.6
A
TJ = 0°C to 70°C (3)
dB
±0.7
TJ = –40°C to 85°C (3)
Gain control linearity (4)
±0.8
TJ = 25°C
VC < −1.8 V
±0.7
TJ = 25°C (2)
±1.1
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
dB/V
±1.9
(3)
±2.7
POWER SUPPLY
TJ = 25°C
+VS = 5 V, G = −40 dB
11.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
Positive maximum supply
quiescent current
10
TJ = 25°C (2)
11.7
TJ = 25°C
+VS = 5 V, G = 40 dB
18
TJ = 25°C (2)
19.5
A
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C
+VS = 5 V, G = −40 dB
21.3
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
8.5
A
mA
8.2
8.1
TJ = 25°C
+VS = 5 V, G = 40 dB
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C (3)
(4)
10
TJ = –40°C to 85°C (3)
Positive minimum supply
quiescent current
(2)
(3)
mA
21
(3)
TJ = 25°C
(1)
mA
11.6
(3)
18
16.5
A
mA
15.5
14.5
Test levels: (A) 100% tested at 25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value; only for information.
Junction temperature = ambient for 25°C tested specifications.
Junction temperature = ambient at low temperature limit; junction temperature = ambient 30°C at high temperature limit for over
temperature specifications.
Maximum deviation from best line fit.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
9
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
High Grade DC Characteristics: VS = ±5 V (VCA810AID) (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, unless otherwise noted.
PARAMETER
TEST LEVEL (1)
TEST CONDITIONS
MIN
TJ = 25°C
−VS = −5 V, G = −40 dB
(3)
14.2
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
20
22
A
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
24.3
12
10
A
mA
9.9
TJ = –40°C to 85°C (3)
Negative minimum supply
quiescent current (5)
9.8
TJ = 25°C
−VS = −5 V, G = 40 dB
TJ = 25°C (2)
TJ = 0°C to 70°C (3)
TJ = –40°C to 85°C (3)
10
mA
24
TJ = 25°C
(5)
mA
14.1
TJ = –40°C to 85°C (3)
−VS = −5 V, G = −40 dB
UNIT
14
A
TJ = 0°C to 70°C (3)
TJ = 25°C
−VS = −5 V, G = 40 dB
MAX
12
TJ = 25°C (2)
TJ = –40°C to 85°C
Negative maximum supply
quiescent current (5)
TYP
20
18
A
mA
17
16.5
Magnitude.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
7.7 Typical Characteristics
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
60
3
Gain (dB)
20
RL = 500W
0
VIN = 100mVPP, VOUT = 1VPP
-3
Gain (dB)
40
VIN = 10mVPP, VOUT = 1VPP
VIN = 1VPP, VOUT = 1VPP
0
VOUT = 2VPP, VIN = 200mVPP
-6
-9
-20
-12
VOUT = 2VPP, VIN = 20mVPP
-40
-15
-60
VC = -1VDC + 10mVPP
-18
1
10
100
1000
1
10
Frequency (MHz)
Figure 1. Small-Signal Frequency Response
Figure 2. Gain Control Frequency Response
0.6
150
G = +40dB
VIN = 2VPP
G = -20dB
VIN = 10mVPP
0.4
Output Voltage (V)
Output Voltage (mV)
100
50
G = -40dB
0
-50
0.2
G = +20dB
0
-0.2
-0.4
-100
-0.6
-150
Time (20ns/div)
Time (20ns/div)
Figure 3. Attenuated Pulse Response
1.2
Figure 4. High Gain Pulse Response
60
G = 0dB to -40dB, VIN = 1VDC
Specified Operating Range
40
1.0
20
0.8
Gain (dB)
Output Voltage (V)
100
Frequency (MHz)
0.6
0.4
0
-20
-40
Output Disabled for
+0.15V £ VC £ +2V
-60
0.2
-80
0
G = 0dB to +40dB, VIN = 10mVDC
-100
-0.2
0.5
Time (20ns/div)
0
-0.5
-1.0
-1.5
-2.0
-2.5
Control Voltage, VC (V)
Figure 5. Gain Control Pulse Response
Figure 6. Gain vs Control Voltage
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
11
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
VO = 1VPP
RL = 500W
Harmonic Distortion (dBc)
-35
-20
G = 0dB, Third Harmonic
G = 0dB, Third Harmonic
Harmonic Distortion (dBc)
-30
-40
-45
-50
G = +40dB, Third Harmonic
-55
G = +40dB, Second Harmonic
-60
-65
-70
-30
-40
G = +40dB, Third Harmonic
-50
-60
G = +40dB, Second Harmonic
f = 1MHz
VO = 1VPP
RL = 500W
-70
G = 0dB, Second Harmonic
-75
G = 0dB, Second Harmonic
-80
0.1
1
10
100
1000
Frequency (MHz)
Load (W)
Figure 7. Harmonic Distortion vs Frequency
f = 1MHz
RL = 500W
Harmonic Distortion (dBc)
-30
Figure 8. Harmonic Distortion vs RLOAD
-20
G = 0dB, Third Harmonic
Harmonic Distortion (dBc)
-20
-40
G = +40dB, Second Harmonic
-50
-60
-70
-80
G = +40dB, Third Harmonic
-90
-30
Third Harmonic
-40
-50
-60
Second Harmonic
-70
G = 0dB, Second Harmonic
-100
-80
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0
1
5
10
15
Figure 9. Harmonic Distortion vs Output Voltage
Input
Limited
Max Useful
Output Voltage
Range
0.1
Resulting
Output Voltage
30
35
40
-20
Output
Limited
Max Useful
Input Voltage Range
25
Figure 10. Harmonic Distortion vs Gain
Harmonic Distortion (dBc)
Input/Output Voltage (VPP)
10
20
Gain (dB)
Output Voltage (VPP)
1
f = 1MHz
VO = 1VPP
RL = 500W
Resulting
Input Voltage
f = 1MHz
VIN = 1VPP
RL = 500W
-30
Third Harmonic
-40
-50
-60
Second Harmonic
-70
Input and Output Measured at 1dB Compression
-80
0.01
-40
-30
-20
-10
0
10
20
30
40
-40
Figure 11. Input, Output Range vs Gain
12
-35
-30
-25
-20
-15
-10
-5
0
Attenuation (dB)
Gain (dB)
Figure 12. Harmonic Distortion vs Attenuation
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Typical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
10000
Input-Referred Voltage Noise Density
10
RS = 20W
on Each Input
en (nV/?Hz)
in (pA/?Hz)
en (nV/?Hz)
eO (nV/?Hz)
1000
100
Differential Input
Voltage Noise (2.4nV/ÖHz)
Output-Referred Voltage Noise Density
10
Current Noise (1.8pA/ÖHz)
Each Input
1
1
0
100
-0.2 -0.4 -0.6 -0.8 -1.0 -1.2 -1.4 -1.6 -1.8 -2.0
1k
10k
100k
1M
10M
Frequency (Hz)
Control Voltage (V)
Figure 14. Input Voltage and Current Noise
Figure 13. Noise Density vs Control Voltage
0
50
40
VC = +0.1V
Isolation (dB)
30
Output Offset Error (mV)
-20
-40
-60
VC = +0.2V
-80
Maximum Error Band
20
10
Typical Devices
0
-10
-20
-30
-100
-40
-120
-50
1M
10M
100M
-40
-30
-20
-10
Frequency (Hz)
Figure 15. Fully Attenuated Isolation vs Frequency
250
Deviation from -40dB/V Gain Slope
20
30
40
Total Tested = 1462
G = +40dB
200
0.2
0.1
Count
Gain Error (dB)
10
Figure 16. Output Offset Voltage Total Error Band vs Gain
0.4
0.3
0
Gain (dB)
0
-0.1
150
100
-0.2
50
-0.3
-0.4
0
-0.5
-1
-1.5
-2
<-50
<-45
<-40
<-35
<-30
<-25
<-20
<-15
<-10
<-5
<0
<5
<10
<15
<20
<25
<30
<35
<40
<45
<50
>50
0
-0.5
Control Voltage (V)
Output Offset Voltage (mV)
Figure 17. Typical Gain Error Plot
Figure 18. Output Offset Voltage Distribution
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
13
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
10
10
9
8
8
Group Delay (ns)
Group Delay (ns)
VO = 1VPP
RL = 500W
VO = 1VPP
RL = 500W
1MHz
7
6
5MHz
5
G = 0dB
6
G = +40dB
4
2
10MHz
4
0
-40
-30
-20
0
-10
10
20
30
1
40
10
Figure 19. Group Delay vs Gain
Figure 20. Group Delay vs Frequency
15
2.5
VOUT
1.5
1.0
10x VIN
0.5
VOUT
10
Input/Output Voltage (mV)
Input/Output Voltage (V)
2.0
0
-0.5
-1.0
-1.5
5
VIN
0
200
-5
-10
-15
-20
-2.0
-25
-2.5
Time (100ns/div)
Time (100ns/div)
Figure 21. Overdrive Recovery at Maximum Gain
110
100
110
100
80
CMRR (dB)
PSRR (dB)
70
60
50
PSRR
40
CMRR,
G = ±40dB
90
CMRR
80
CMRR (dB)
PSRR (dB)
Figure 22. Overdrive Recovery at Maximum Attenuation
Input-Referred
90
70
60
50
CMRR,
G = 0dB
40
30
30
20
20
10
10
0
PSRR, G = 0dB
PSRR,
G = +40dB
0
-40
-30
-20
-10
0
10
20
30
40
0.1
Gain (dB)
1
10
100
Frequency (MHz)
Figure 23. Common-Mode Rejection Ratio and
Power-Supply Rejection Ratio vs Gain
14
100
Frequency (MHz)
Gain (dB)
Figure 24. Common-Mode Rejection Ratio and
Power-Supply Rejection Ratio vs Frequency
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Typical Characteristics (continued)
6
6
5
5
4
4
Gain (dB)
Gain (dB)
At RL = 500 Ω and VIN = single-ended input on V+ with V− at ground, VS = ±5 V, unless otherwise noted.
3
3
2
2
1
1
0
0
1k
10k
100k
1M
10M
100M
1k
10k
Frequency (Hz)
20
20
19
Input Bias Current (IB)
10
8
5
6
0
4
10x Input Offset Current (IOS)
-5
17
16
14
13
-10
0
-15
11
-20
10
-2
-25
0
25
50
75
100
125
Quiescent Current
for -VS
15
2
-50
100M
18
Supply Current (mA)
15
12
10
10M
Figure 26. Gain Control −PSRR at Max Gain
25
Output Offset Voltage (mA)
Input Bias and Offset Current (mA)
Output Offset Voltage (VOS)
14
1M
Frequency (Hz)
Figure 25. Gain Control +PSRR at Max Gain
16
100k
12
Quiescent Current
for +VS
0
-0.5
-1.0
-1.5
-2.0
Control Voltage (V)
Temperature (°C)
Figure 27. Typical DC Drift vs Temperature
Figure 28. Typical Supply Current vs Control Voltage
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
15
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
8 Detailed Description
8.1 Overview
The VCA810 is a high gain adjust range, wideband, voltage amplifier with a voltage-controlled gain, as shown in
Functional Block Diagram. The circuit’s basic voltage amplifier responds to the control of an internal gain-control
amplifier. At its input, the voltage amplifier presents the high impedance of a differential stage, permitting flexible
input impedance matching. To preserve termination options, no internal circuitry connects to the input bases of
this differential stage. For this reason, the user must provide DC paths for the input base currents from a signal
source, either through a grounded termination resistor or by a direct connection to ground. The differential input
stage also permits rejection of common-mode signals. At its output, the voltage amplifier presents a low
impedance, simplifying impedance matching. An open-loop design produces wide bandwidth at all gain settings.
A ground-referenced differential to single-ended conversion at the output retains the low output offset voltage.
A gain control voltage, VC, controls the amplifier gain magnitude through a high-speed control circuit. Gain
polarity can be either inverting or noninverting, depending upon the amplifier input driven by the input signal. The
gain control circuit presents the high-input impedance of a noninverting operational amplifier connection. The
control voltage pin is referred to ground as shown in Functional Block Diagram. The control voltage VC varies the
amplifier gain according to the exponential relationship:
G(V/V) = 10
-2 (VC + 1)
(1)
This translates to the log gain relationship:
G(dB) = –40 × (VC + 1)dB
(2)
Thus, G(dB) varies linearly over the specified −40 dB to 40 dB range as VC varies from 0 V to −2 V. Optionally,
making VC slightly positive (≥ 0.15 V) effectively disables the amplifier, giving greater than 80 dB of signal path
attenuation at low frequencies.
Internally, the gain-control circuit varies the amplifier gain by varying the transconductance, gm, of a bipolar
transistor using the transistor bias current. Varying the bias currents of differential stages varies gm to control the
voltage gain of the VCA810. A gm-based gain adjust normally suffers poor thermal stability. The VCA810
includes circuitry to minimize this effect.
8.2 Functional Block Diagram
+5V
6
V+
V-
VCA810
1
8
Gain
Adjust
+
X1
5
VOUT
2
VC
3
0 ® -2V
-40dB ® +40dB Gain
7
-5V
8.3 Feature Description
8.3.1 Input and Output Range
The VCA810’s 80 dB gain range allows the user to handle an exceptionally wide range of input signal levels. If
the input and output voltage range specifications are exceeded, however, signal distortion and amplifier overdrive
will occur. Figure 11 shows the maximum input and output voltage range. This chart plots input and output
voltages versus gain in dB.
16
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Feature Description (continued)
The maximum input voltage range is the largest at full attenuation (−40 dB) and decreases as the gain increases.
Similarly, the maximum useful output voltage range increases as the input decreases. We can distinguish three
overloading issues as a result of the operating mode: high attenuation, mid-range gain-attenuation, and high
gain.
From –40 dB to –10 dB, gain overdriving the input stage is the only method to overdrive the VCA810. Preventing
this type of overdrive is achieved by limiting the input voltage range.
From –10 dB to 40 dB, overdriving can be prevented by limiting the output voltage range. There are two limiting
mechanisms operating in this situation. From –10 dB to 10 dB, an internal stage is the limiting factor; from 10 dB
to 40 dB, the output stage is the limiting factor.
Output overdriving occurs when either the maximum output voltage swing or output current is exceeded. The
VCA810 high output current of ±60 mA ensures that virtually all output overdrives will be limited by voltage swing
rather than by current limiting. Table 1 summarizes these overdrive conditions.
Table 1. Output Signal Compression
GAIN RANGE
LIMITING MECHANISM
TO PREVENT, OPERATE DEVICE WITHIN:
−40 dB < G < −10 dB
Input Stage Overdrive
Input Voltage Range
−10 dB < G < 10 dB
Internal Stage Overdrive
Output Voltage Range
5 dB < G < 40 dB
Output Stage Overdrive
Output Voltage Range
8.3.2 Overdrive Recovery
As shown in Figure 11, the onset of overdrive occurs whenever the actual output begins to deviate from the ideal
expected output. If possible, the user should operate the VCA810 within the linear regions shown in order to
minimize signal distortion and overdrive delay time. However, instances of amplifier overdrive are quite common
in automatic gain control (AGC) circuits, which involve the application of variable gain to input signals of varying
levels. The VCA810 design incorporates circuitry that allows it to recover from most overdrive conditions in 200
ns or less. Overdrive recovery time is defined as the time required for the output to return from overdrive to linear
operation, following the removal of either an input or gain-control overdrive signal. See Typical Characteristics for
the overdrive plots for maximum gain and maximum attenuation.
8.3.3 Output Offset Error
Several elements contribute to the output offset voltage error; among them are the input offset voltage, the
output offset voltage, the input bias current and the input offset current. To simplify the following analysis, the
output offset voltage error is dependent only on the output-offset voltage of the VCA810 and the input offset
voltage. The output offset error can then be expressed as Equation 3:
G
(
(
+ 10 20 · V
dB
VOS = VOSO
IOS
where
•
•
•
•
VOS = Output offset error
VOSO = Output offset voltage
GdB = VCA810 gain in dB
VIOS = Input offset voltage
(3)
This is shown in Figure 29.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
17
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
50
Output Offset Error (mV)
40
30
Maximum Error Band
20
10
Typical Devices
0
-10
-20
-30
-40
-50
-40
-30
-20
0
-10
10
20
30
40
Gain (dB)
Figure 29. Output Offset Error versus Gain
Figure 18 shows the distribution for the output offset voltage at maximum gain.
8.3.4 Offset Adjustment
Where desired, the offset of the VCA810 can be removed as shown in Figure 30. This circuit simply presents a
DC voltage to one of the amplifier inputs to counteract the offset error voltage. For best offset performance, the
trim adjustment should be made with the amplifier set at the maximum gain of the intended application. The
offset voltage of the VCA810 varies with gain as shown in Figure 29, limiting the complete offset cancellation to
one selected gain. Selecting the maximum gain optimizes offset performance for higher gains where high
amplification of the offset effects produces the greatest output offset. Two features minimize the offset control
circuit noise contribution to the amplifier input circuit. First, making the resistance of R2 a low value minimizes the
noise directly introduced by the control circuit. This approach reduces both the thermal noise of the resistor and
the noise produced by the resistor with the amplifier input noise current. A second noise reduction results from
capacitive bypass of the potentiometer output. This reduction filters out power-supply noise that would otherwise
couple to the amplifier input.
V+
R1 VIN
10kW
RV
100kW
V-
1 mF
VCA810
R2
10W
VO
VC
Figure 30. Optional Offset Adjustment
This filtering action diminishes as the wiper position approaches either end of the potentiometer, but practical
conditions prevent such settings. Over its full adjustment range, the offset control circuit produces a ±5-mV input
offset correction for the values shown. However, the VCA810 only requires one-tenth of this range for offset
correction, assuring that the potentiometer wiper will always be near the potentiometer center. With this setting,
the resistance seen at the wiper remains high, which stabilizes the filtering function.
18
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
8.3.5 Gain Control
The VCA810 gain is controlled by means of a unipolar negative voltage applied between ground and the gain
control input, pin 3. If use of the output disable feature is required, a ground-referenced bipolar voltage is
needed. Output disable occurs for 0.15 V ≤ VC ≤ 2 V, and produces greater than 80 dB of attenuation. The
control voltage should be limited to 2 V in disable mode, and –2.5 V in gain mode to prevent saturation of internal
circuitry. The VCA810 gain-control input has a –3-dB bandwidth of 25 MHz and varies with frequency, as shown
in Typical Characteristics. This wide bandwidth, although useful for many applications, can allow high-frequency
noise to modulate the gain control input. In practice, this can be easily avoided by filtering the control input, as
shown in Figure 31. RP should be no greater than 100 Ω so as not to introduce gain errors by interacting with the
gain control input bias current of 6 μA.
VO
VCA610
CP
f-3dB =
1
2pRPCP
RP
VC
Figure 31. Control Line Filtering
8.3.6 Gain Control and Teeple Point
When the VCA810 control voltage reaches −1.5 V, also referred to as the Teeple point, the signal path
undergoes major changes. From 0 V to the Teeple point, the gain is controlled by one bank of amplifiers: a lowgain VCA. As the Teeple point is passed, the signal path is switched to a higher gain VCA. This gain-stage
switching can be seen most clearly in Figure 13. The output-referred voltage noise density increases
proportionally to the control voltage and reaches a maximum value at the Teeple point. As the gain increases
and the internal stages switch, the output-referred voltage noise density drops suddenly and restarts its
proportional increase with the gain.
8.3.7 Noise Performance
The VCA810 offers 2.4-nV/√Hz input-referred voltage noise and 1.8-pA/√Hz input-referred current noise at a gain
of 40 dB. The input-referred voltage noise, and the input-referred current noise terms, combine to give low output
noise under a wide variety of operating conditions. Figure 32 shows the operational amplifier noise analysis
model with all the noise terms included. In this model, all noise terms are taken to be noise voltage or current
density terms in either nV/√Hz or pA/√Hz.
+5V
IBN
*
RS
ERS
*
4kTRS
IBI
-
ENI
VCA810
EO
VC
RT
*
-5V
4kTRT
Figure 32. VCA810 Noise Analysis Model
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
19
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
The total output spot noise voltage can be computed as the square root of the sum of all squared output noise
voltage contributors. Equation 4 shows the general form for the output noise voltage using the terms shown in
Figure 32.
EO = G(V/V)·
2
2
2
ENI + (IBIRT) + (IBNRS) + 4kT(RS + RT)
(4)
Dividing this expression by the gain will give the equivalent input-referred spot-noise voltage at the noninverting
input as shown by Equation 5.
EN =
2
ENI2 + (IBIRT)2 + (IBNRS) + 4kT(RS + RT)
(5)
Evaluating these two equations for the VCA810 circuit and component values shown in Figure 34 (maximizing
gain) will give a total output spot-noise voltage of 272.3 nV√Hz and a total equivalent input-referred spot-noise
voltage of 2.72 nV√Hz. This total input-referred spot-noise voltage is higher than the 2.4-nV√Hz specification for
the VCA810 alone. This reflects the noise added to the output by the input current noise times the input
resistance RS and RT. Keeping input impedance low is required to maintain low total equivalent input-referred
spot-noise voltage.
8.3.8 Input and ESD Protection
The VCA810 is built using a very high-speed complementary bipolar process. The internal junction breakdown
voltages are relatively low for these very small geometry devices. These breakdowns are reflected in Absolute
Maximum Ratings
All pins on the VCA810 are internally protected from ESD by means of a pair of back-to-back, reverse-biased
diodes to either power supply, as shown in Figure 33. These diodes begin to conduct when the pin voltage
exceeds either power supply by about 0.7 V. This situation can occur with loss of the amplifier power supplies
while a signal source is still present. The diodes can typically withstand a continuous current of 30 mA without
destruction. To ensure long-term reliability, however, diode current should be externally limited to 10 mA
whenever possible.
+VS
ESD Protection diodes internally
connected to all pins.
External
Pin
Internal
Circuitry
-VS
Figure 33. Internal ESD Protection
8.4 Device Functional Modes
The VCA824 functions as a differential input, single-ended output variable gain amplifier. This functional mode is
enabled by applying power to the amplifier supply pins and is disabled by turning the power off.
The gain is continuously variable through the analog gain control input. The gain is set by an external, analog,
control voltage as shown in the functional block diagram. The signal gain is equal to G = (V/V) 10–2(V + 1) as
detailed in Overview. The gain changes in a linear in dB fashion with over 80 dB of gain range from –2-V to –0-V
control voltage. As with most other differential input amplifiers, inputs can be applied to either one or both of the
amplifier inputs. The amplifier gain is controlled through the gain control pin.
In addition to gain control, the gain control pin can also be used to disable the amplifier. This is accomplished by
applying a slightly positive voltage to this pin. This is detailed Feature Description.
20
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
9 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
9.1.1 VCA810 Operation
Figure 34 shows the circuit configuration used as the basis of the Electrical Characteristics and Typical
Characteristics. Voltage swings reported in the specifications are taken directly at the input and output pins. For
test purposes, the input impedance is set to 50 Ω with a resistance to ground. A 25-Ω resistance (RT) is included
on the V− input to get bias current cancellation. Proper supply bypassing is shown in Figure 34, and consists of
two capacitors on each supply pin: one large electrolytic capacitor (2.2 μF to 6.8 μF), effective at lower
frequencies, and one small ceramic capacitor (0.1 μF) for high-frequency decoupling.
+5V -5V
0.1mF
0.1mF
6.8mF
+
6.8mF
+
6
1
VI
50W
Source
RS
50W
7
2
VCA810
5
3
8
RT
25W
VO
RL
500W
RC
VC
Figure 34. Variable Gain, Specification and Test Circuit
Notice that both inverting and noninverting inputs are connected to ground with a resistor (RS and RT). Matching
the DC source impedance looking out of each input will minimize input offset voltage error.
9.1.2 Range-Finding TGC Amplifier
The block diagram in Figure 35 illustrates the fundamental configuration common to pulse-echo range finding
systems. A photodiode preamp provides an initial gain stage to the photodiode.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
21
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Application Information (continued)
20W
OPA657
ADC
and DSP
VCA810
20kW
20W
VC
CF
VC
-VB
t
0
-2V
Time-Gain Compensated Control Voltage
Figure 35. Typical Range-Finding Application
The control voltage VC varies the amplifier gain for a basic signal-processing requirement: compensation for
distance attenuation effects, sometimes called time-gain compensation (TGC). Time-gain compensation
increases the amplifier gain as the signal moves through the air to compensate for signal attenuation. For this
purpose, a ramp signal applied to the VCA810 gain control input linearly increases the dB gain of the VCA810
with time.
9.1.3 Wide-Range AGC Amplifier
The voltage-controlled gain feature of the VCA810 makes this amplifier ideal for precision AGC applications with
control ranges as large as 60 dB. The AGC circuit of Figure 36 adds an operational amplifier and diode for
amplitude detection, a hold capacitor to store the control voltage and resistors R1 through R3 that determine
attack and release times. Resistor R4 and capacitor CC phase-compensate the AGC feedback loop. The
operational amplifier compares the positive peaks of output VO with a DC reference voltage, VR. Whenever a VO
peak exceeds VR, the OPA820 output swings positive, forward-biasing the diode and charging the holding
capacitor. This charge drives the capacitor voltage in a positive direction, reducing the amplifier gain. R3 and the
CH largely determine the attack time of this AGC correction. Between gain corrections, resistor R1 charges the
capacitor in a negative direction, increasing the amplifier gain. R1, R2, and CH determine the release time of this
action. Resistor R2 forms a voltage divider with R1, limiting the maximum negative voltage developed on CH. This
limit prevents input overload of the VCA810 gain control circuit.
Figure 37 shows the AGC response for the values shown in Figure 36.
VIN
RSSI
Port
2mV to 2V
100kHz
VO
VCA810
VC
VOUT PEAK = VR
R3
1kW HP5082
OPA820
R1
50kW
R2
50kW
CH
0.1mF
R4
100W
VR
CC
47pF
0.1 VDC
V-
Figure 36. 60-dB Input Range AGC
22
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Application Information (continued)
Output Voltage (50mV/div)
0.15
0.10
0.05
VIN = 100mVPP
VIN = 1VPP
0
-0.05
-0.10
VIN = 10mVPP
-0.15
-0.20
Time (5ms/div)
Figure 37. AGC Output Voltage for 100-kHz Sinewave at 10 mVPP, 100 mVPP, and 1 VPP
9.1.4 Stabilized Wein-Bridge Oscillator
Adding Wein-bridge feedback to the above AGC amplifier produces an amplitude-stabilized oscillator. As
Figure 38 shows, this alternative requires the addition of just two resistors (RW1, RW2) and two capacitors
(CW1, CW2).
Connecting the feedback network to the amplifier noninverting input introduces positive feedback to induce
oscillation. The feedback factor displays a frequency dependence due to the changing impedances of the CW
capacitors. As frequency increases, the decreasing impedance of the CW2 capacitor increases the feedback
factor. Simultaneously, the decreasing impedance of the CW1 capacitor decreases this factor. Analysis shows
1
fW =
2pRWCW Hz, making this the frequency most conducive to oscillation. At
that the maximum factor occurs at
this frequency, the impedance magnitude of CW equals RW, and inspection of the circuit shows that this condition
produces a feedback factor of 1/3. Thus, self-sustaining oscillation requires a gain of three through the amplifier.
The AGC circuitry establishes this gain level. Following initial circuit turn-on, R1 begins charging CH negative,
increasing the amplifier gain from its minimum. When this gain reaches three, oscillation begins at fW; the
continued charging effect of R1 makes the oscillation amplitude grow. This growth continues until that amplitude
reaches a peak value equal to VR. Then, the AGC circuit counteracts the R1 effect, controlling the peak amplitude
at VR by holding the amplifier gain at a level of three. Making VR an AC signal, rather than a DC reference,
produces amplitude modulation of the oscillator output.
RW2
300W
CW1
4700pF
CW2
4700pF
f = 1/2pRW1CW1
RW1 = RW2
CW1 = CW2
RW1
300W
VO
VCA810
VC
VOPEAK = VR
R3
1kW
HP5082
OPA820
R1
50kW
R2
50kW
CH
1mF
R4
100W
VR
0.1 VDC
CC
10pF
V-
Figure 38. Amplitude-Stabilized Oscillator
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
23
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Application Information (continued)
9.1.5 Low-Drift Wideband Log Amplifier
The VCA810 can be used to provide a 2.5-MHz (–3 dB) log amp with low offset voltage and low gain drift. The
exponential gain-control characteristic of the VCA810 permits simple generation of a temperature-compensated
logarithmic response. Enclosing the exponential function in an op-amp feedback path inverts this function,
producing the log response. Figure 39 shows the practical implementation of this technique. A DC reference
voltage, VR, sets the VCA810 inverting input voltage. This configuration makes the amplifier output voltage
VOA = −GVR, where G = 10
-2 (VC + 1)
.
VR
-10mV
VOA = -GVR
VCA810
VC
(
VOL = - 1 +
R1
470W
R2
330W
VOL
OPA820
R1
R2
) 1 + 0.5 Log(-V
IN/VR)
R3
100W
VIN
CC
50pF
Figure 39. Temperature-Compensated Log Response
A second input voltage also influences VOA through control of gain G. The feedback operational amplifier forces
VOA to equal the input voltage VIN connected at the operational amplifier inverting input. Any difference between
these two signals drops across R3, producing a feedback current that charges CC. The resulting change in VOL
adjusts the gain of the VCA810 to change VOA.
At equilibrium:
VOA = VIN = -VR · 10
-2 (VC + 1)
(6)
The operational amplifier forces this equality by supplying the gain control voltage,
VC =
R1 · VOL
R 1 + R2 .
Combining the last two expressions and solving for VOL yields the circuit’s logarithmic response:
(
VOL = - 1 +
R2
R1
( · 1 + 0.5·log ( - VV (
IN
R
(7)
An examination of this result illustrates several circuit characteristics. First, the argument of the log term, −VIN/VR,
reveals an option and a constraint. In Figure 39, VR represents a DC reference voltage. Optionally, making this
voltage a second signal produces log-ratio operation. Either way, the log term’s argument constrains the
polarities of VR and VIN. These two voltages must be of opposite polarities to ensure a positive argument. This
polarity combination results when VR connects to the inverting input of the VCA810. Alternately, switching VR to
the amplifier noninverting input removes the minus sign of the log term argument. Then, both voltages must be of
the same polarity in order to produce a positive argument. In either case, the positive polarity requirement of the
argument restricts VIN to a unipolar range. Figure 40 illustrates these constraints.
24
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Application Information (continued)
5
4
Output Voltage (V)
3
2
1
0
-1
II
I
-2
III
-3
-4
-5
0.001
0.01
0.1
1
10
100
VIN/VR Voltage Ratio
Figure 40. Test Result for LOG Amp for VR = −100 mV
The above VOL expression reflects a circuit gain introduced by the presence of R1 and R2. This feature adds a
convenient scaling control to the circuit. However, a practical matter sets a minimum level for this gain. The
voltage divider formed by R1 and R2 attenuates the voltage supplied to the VC terminal by the operational
amplifier. This attenuation must be great enough to prevent any possibility of an overload voltage at the VC
terminal. Such an overload saturates the VCA810 gain-control circuitry, reducing the amplifier’s gain. For the
feedback connection of Figure 39, this overload condition permits a circuit latch. To prevent this, choose R1 and
R2 to ensure that the operational amplifier cannot possibly deliver a more negative input than −2.5 V to the VC
terminal.
Figure 40 exhibits three zones of operation described below:
Zone I: VC > 0 V. The VCA810 is operating in full attenuation (−80 dB). The noninverting input of the OPA820
will see ∼0 V. VOL is going to be the integration of the input signal.
Zone II: −2 V < VC < 0 V. The VCA810 is in its normal operating mode, creating the log relationship in
Equation 7.
Zone III: VC < −2 V. The VCA810 control pin is out of range, and some measure should be taken so that it does
not exceed –2.5 V. A limiting action could be achieved by using a voltage limiting amplifier.
9.1.6 Voltage-Controlled Low-Pass Filter
In the circuit of Figure 41, the VCA810 serves as the variable-gain element of a voltage-controlled low-pass filter.
This section discusses how this implementation expands the circuit voltage swing capability over that normally
achieved with the equivalent multiplier implementation. The circuit response pole responds to control voltage VC,
according to the relationship in Equation 8:
G
fP =
2pR2C
where
•
G = 10
-2 (VC + 1)
(8)
With the components shown, the circuit provides a linear variation of the low-pass cutoff from 300 Hz to 1 MHz.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
25
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Application Information (continued)
R2
330W
C
0.047mF
R1
330W
VI
OPA820
VOA
VO
VCA810
VC
VO = - R 2
·
R1
VI
fP =
1
1+s
R 2C 2
G
G
2pR2C
-2 (VC + 1)
G = 10
Figure 41. Tunable Low-Pass Filter
The response control results from amplification of the feedback voltage applied to R2. First, consider the case
where the VCA810 produces G = 1. Then, the circuit performs as if this amplifier were replaced by a short circuit.
Visually doing so leaves a simple voltage amplifier with a feedback resistor bypassed by a capacitor. This basic
G
fP =
2
p
R2C .
circuit produces a response pole at
For G > 1, the circuit applies a greater voltage to R2, increasing the feedback current this resistor supplies to the
summing junction of the OPA820. The increased feedback current produces the same result as if R2 had been
decreased in value in the basic circuit described above. Decreasing the effective R2 resistance moves the circuit
G
fP =
2
p
R2C response control.
pole to a higher frequency, producing the
Finite loop gain and a signal-swing limitation set performance boundaries for the circuit. Both limitations occur
when the VCA810 attenuates, rather than amplifies, the feedback signal. These two limitations reduce the
circuit’s utility at the lower extreme of the VCA810 gain range. For −1 ≤ VC ≤ 0, this amplifier produces
attenuating gains in the range from 0 dB to −40 dB. This range directly reduces the net gain in the circuit’s
feedback loop, increasing gain error effects. Additionally, this attenuation transfers an output swing limitation from
the OPA820 output to the overall circuit’s output. Note that OPA820 output voltage, VOA, relates to VO through
the expression, VO = G × VOA. Thus, a G < 1 limits the maximum VO swing to a value less than the maximum
VOA swing.
Figure 42 shows the low-pass frequency for different control voltages.
26
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Application Information (continued)
3
0
VC = -2V
Gain (dB)
-3
VC = -1.4V
-6
VC = -1.6V
VC = -1.8V
-9
-12
-15
10k
100k
1M
10M
Frequency (Hz)
Figure 42. Voltage-Controlled Low-Pass Filter Frequency Response
9.1.7 Tunable Equalizer
A circuit analogous to the above low-pass filter produces a voltage-controlled equalizer response. The gain
control provided by the VCA810 of Figure 43 varies this circuit response zero from 1 Hz to 10 kHz, according to
the relationship of Equation 9:
G
fZ ≈
2pGR1C
(9)
To visualize the circuit’s operation, consider a circuit condition and an approximation that permit replacing the
VCA810 and R3 with short circuits. First, consider the case where the VCA810 produces G = 1. Replacing this
amplifier with a short circuit leaves the operation unchanged. In this shorted state, the circuit is simply a voltage
amplifier with an R-C bypass around R1. The resistance of this bypass, R3, serves only to phase-compensate the
circuit, and practical factors make R3 << R1. Neglecting R3 for the moment, the circuit becomes just a voltage
1
fZ ≈
2
p
R
1C .
amplifier with a capacitive bypass of R . This circuit produces a response zero at
1
Adding the VCA810 as shown in Figure 43 permits amplification of the signal applied to capacitor C, and
produces voltage control of the frequency fZ. Amplified signal voltage on C increases the signal current
conducted by the capacitor to the operational amplifier feedback network. The result is the same as if C had
been increased in value to GC. Replacing C with this effective capacitance value produces the circuit control
1
fZ ≈
2
p
R
1GC .
expression
R1
750W
R2
750W
OPA820
VI
50W
VCA810
VOA
C
2 mF
R3
3W
OPA846
50W
fZ ≈
1
2p(GR1 + R3C)
VO
VC
with G = 10
-2 (VC + 1)
Figure 43. Tunable Equalizer
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
27
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
Application Information (continued)
Another factor limits the high-frequency performance of the resulting high-pass filter: the finite bandwidth of the
operational amplifier. This limits the frequency duration of the equalizer response. Limitations such as bandwidth
and stability are clearly shown in Figure 44.
100
AOL
90
G = +40dB
80
Gain (dB)
70
G = +15dB
60
50
40
G = -15dB
30
20
G = -40dB
10
0
1
10
100
1k
10k
100k
1M
10M
100M
Frequency (Hz)
Figure 44. Amplifier Noise Gain and AOL for Different Gain
Other limitations of this circuit are stability versus VCA810 gain and input signal level for the circuit. Figure 44
also illustrates these two factors. As the VCA810 gain increases, the crossover slope between the AOL curve of
the OPA846 and noise gain will be greater than 20 dB/decade, rendering the circuit unstable. The signal level for
high gain of the VCA810 will meet two limitations: the output voltage swings of both the VCA810 and the
OPA846. The expression VOA = GVI relates these two voltages. Thus, an output voltage limit VOAL constrains the
input voltage to VI ≤ VOAL/G.
With the components shown, BW = 50 kHz. This bandwidth provides an integrator response duration of four
decades of frequency for fZ = 1 Hz, dropping to one decade for fZ = 10 kHz.
9.1.8 Voltage-Controlled Band-Pass filter
The variable gain of the VCA810 also provides voltage control over the center frequency of a band-pass filter. As
shown in Figure 45, this filter follows from the state-variable configuration with the VCA810 replacing the inverter
common to that configuration. Variation of the VCA810 gain moves the filter’s center frequency through a 100:1
range following the relationship of Equation 10:
10-(V + 1)
2pRC
C
fO =
(10)
As before, variable gain controls a circuit time constant to vary the filter response. The gain of the VCA810
amplifies or attenuates the signal driving the lower integrator of the circuit. This amplification alters the effective
resistance of the integrator time constant, producing the response of Equation 11:
- s
VO
nRC
=
VI
G
s
s2 + nRC + 2 2
RC
(11)
Evaluation of this response equation reveals a passband gain of AO = –1, a bandwidth of BW = 1/(2πRC), and a
- (VC + 1)
selectivity of Q = n · 10
. Note that variation of control voltage VC alters Q but not bandwidth.
The gain provided by the VCA810 restricts the output swing of the filter. Output signal VO must be constrained to
a level that does not drive the VCA810 output, VOA, into its saturation limit. Note that these two outputs have
voltage swings related by VOA = GVO. Thus, a swing limit VOAL imposes a circuit output limit of VOL ≤ VOAL/G.
See Figure 46 for the frequency response for two different gain conditions of the schematic shown in Figure 45.
In particular, notice the center frequency shift and the selectivity of Q changing as the gain is increased.
28
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
Application Information (continued)
C
0.047mF
nR
5kW
nR
5kW
VO
=
VI
VI
R
330W
s
nRC
G
s
s2 + nRC + 2 2
RC
-
10-(V + 1)
2pRC
C
1/2
OPA2822
fO =
VO
C
0.047mF
BW =
50W
R
330W
1/2
OPA2822
VOA
1
2pRC
Q = n·10
-(VC + 1)
VCA810
AO = -1
50W
VC
Figure 45. Tunable Band-Pass Filter
0
-5
-10
Gain (dB)
-15
-20
-25
-30
-35
-40
-45
-50
100
1k
10k
100k
Frequency (Hz)
Figure 46. Tunable Band-Pass Filter Response
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
29
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
9.2 Typical Application
A common use of the log amplifier above involves signal compounding. The inverse function, signal expanding,
requires an exponential transfer function. The VCA810 produces this latter response directly, as shown in
Figure 47. DC reference VR again sets the amplifier input voltage, and the input signal VIN now drives the gain
control point. Resistors R1 and R2 attenuate this drive to prevent overloading the gain control input. Setting these
resistors at the same values as in the preceding log amp produces an exponential amplifier with the inverse
function of the log amplifier.
Testing the circuit given in Figure 47 gives the exponential response shown in Figure 48.
VR
-10mV
VCA810
VOL = -VR x 10
+0.5V
-2
(
(
R1VIN
+1
R1 + R2
VC
VI
R2
330W
OPA698
R1
470W
VL
-3.4V
500W
500W
VIN
Figure 47. Exponential Amplifier
9.2.1 Design Requirements
To build a wide dynamic range wide exponential amplifier we need an amplifier with continuous voltage gain
control, gain range over 40 dB, low noise, and high maximum gain. The VCA810 has ±40 dB of gain range, so it
meets this criteria. It also has continuous voltage gain control and can support up to 100 V/V of voltage gain.
9.2.2 Detailed Design Procedure
An exponential amplifier will have a linear response on a logarithmic scale. The linear in dB gain control of the
VCA810 is ideal for this application. Note that the input to this circuit is the gain control pin. Using the gain
control pin as the input is what gives an exponential gain response. The design involves the use of an OPA698
to provide the proper DC bias voltage to the gain control pin on the VCA810. The OPA698 supply voltage was
chosen based on the input voltage requirement of the VCA810. The reference voltage (VR) is used to set the DC
output voltage. The reference voltage cannot be 0 V, but it must be small so that at maximum gain the amplifier
outputs are not saturated. In Figure 47 design the reference voltage is set to –10 mV.
9.2.3 Application Curve
Output Voltage (V)
1
0.1
0.01
0.001
+3.0
+2.5
+2.0
+1.5
+1.0
+0.5
0
Input Voltage (V)
Figure 48. Exponential Amplifier Response
30
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
10 Power Supply Recommendations
The VCA810 is designed for split supply operation with a nominal supply condition of 6 V. A power supply in the
range of 8 V to 12 V is acceptable, and balanced supplies (negative and positive voltages equal) are
recommended.
The power supply should be regulated to 10% or better accuracy and capable of sourcing 100 mA of current.
The device quiescent current is approximately 20 mA and the load current can be up to 60 mA.
Single supply applications are possible, however, the control voltage is referenced to the ground pin, so a single
supply application will require a mid supply reference voltage that can be applied to the ground pin. This
reference voltage should be set to 5% accuracy or better for accurate gain control.
11 Layout
11.1 Layout Guidelines
Achieving optimum performance with a high-frequency amplifier such as the VCA810 requires careful attention to
board layout parasitic and external component types. Recommendations that will optimize performance include:
• Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. This includes the ground pin
(pin 2). Parasitic capacitance on the output can cause instability: on both the inverting input and the
noninverting input, it can react with the source impedance to cause unintentional band limiting. To reduce
unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power
planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board.
Place a small series resistance (> 25 Ω) with the input pin connected to ground to help decouple package
parasitic.
• Minimize the distance (less than 0.25” or 6.35 mm) from the power-supply pins to high-frequency 0.1-μF
decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity
to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and
the decoupling capacitors. The power-supply connections should always be decoupled with these capacitors.
Larger (2.2 μF to 6.8 μF) decoupling capacitors, effective at lower frequencies, should also be used on the
main supply pins. These capacitors may be placed somewhat farther from the device and may be shared
among several devices in the same area of the PCB.
• Careful selection and placement of external components will preserve the high-frequency performance of the
VCA810. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a
tighter overall layout. Metal-film and carbon composition, axially-leaded resistors can also provide good highfrequency performance. Again, keep the leads and PCB trace length as short as possible. Never use wirewound type resistors in a high-frequency application. Since the output pin is the most sensitive to parasitic
capacitance, always position the series output resistor, if any, as close as possible to the output pin. Other
network components, such as inverting or noninverting input termination resistors, should also be placed
close to the package.
• Careful selection and placement of external components will preserve the high-frequency performance of the
VCA810. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a
tighter overall layout. Metal-film and carbon composition, axially-leaded resistors can also provide good highfrequency performance. Again, keep the leads and PCB trace length as short as possible. Never use wirewound type resistors in a high-frequency application. Since the output pin is the most sensitive to parasitic
capacitance, always position the series output resistor, if any, as close as possible to the output pin. Other
network components, such as inverting or noninverting input termination resistors, should also be placed
close to the package.
• Socketing a high-speed part like the VCA810 is not recommended. The additional lead length and pin-to-pin
capacitance introduced by the socket can create an extremely troublesome parasitic network, which can
make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by
soldering the VCA810 onto the board.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
31
VCA810
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
www.ti.com
11.2 Layout Example
Figure 49. Layout Example
11.2.1 Thermal Analysis
The VCA810 will not require heatsinking or airflow in most applications. Maximum desired junction temperature
would set the maximum allowed internal power dissipation as described in this section. In no case should the
maximum junction temperature be allowed to exceed 150°C.
Operating junction temperature (TJ) is given by Equation 12:
TJ = TA + PD ´ qJA
(12)
The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipated in
the output stage (PDL) to deliver load power. Quiescent power is simply the specified no-load supply current
times the total supply voltage across the part. PDL depends on the required output signal and load; for a
grounded resistive load, however, it is at a maximum when the output is fixed at a voltage equal to one-half of
either supply voltage (for equal bipolar supplies). Under this worst-case condition, PDL = VS.2/(4 ● RL), where RL
is the resistive load.
Note that it is the power in the output stage and not in the load that determines internal power dissipation. As a
worst-case example, compute the maximum TJ using an VCA810ID (SO-8 package) in the circuit of Figure 34
operating at maximum gain and at the maximum specified ambient temperature of 85°C.
PD = 10 V(24.8 mA) + 52/(4 × 500 Ω) = 260.5 mW
Maximum TJ = 85°C + (0.260 W ×125°C/W) = 117.6°C
(13)
(14)
This maximum operating junction temperature is well below most system level targets. Most applications will be
lower since an absolute worst-case output stage power was assumed in this calculation of VS/2 which is beyond
the output voltage range for the VCA810.
32
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
VCA810
www.ti.com
SBOS275G – JUNE 2003 – REVISED DECEMBER 2015
12 Device and Documentation Support
12.1 Device Support
12.1.1 Development Support
12.1.1.1 Demonstration Boards
A printed circuit board (PCB) is available to assist in the initial evaluation of circuit performance using the
VCA810. This evaluation board (EVM) is available free, as an unpopulated PCB delivered with descriptive
documentation. The summary information for this board is shown in the DEM-VCA-SO-1A user's guide.
12.1.1.2 Macromodels and Applications Support
Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of
analog circuits and systems. This is particularly true for video and RF amplifier circuits where parasitic
capacitance and inductance can play a major role in circuit performance. A SPICE model for the VCA810 is
available through the TI web page. The applications group is also available for design assistance. The models
available from TI predict typical small-signal AC performance, transient steps, DC performance, and noise under
a wide variety of operating conditions. The models include the noise terms found in the electrical specifications of
the relevant product data sheet.
12.2 Documentation Support
12.2.1 Related Documentation
Unity-Gain Stable, Low-Noise, Voltage-Feedback Operational Amplifier, SBOS303
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2003–2015, Texas Instruments Incorporated
Product Folder Links: VCA810
33
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
VCA810AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
A
VCA810AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
A
VCA810AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
A
VCA810ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
VCA810IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
VCA810IDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
VCA810IDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
VCA
810
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
10-Jun-2014
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Mar-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
VCA810AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
VCA810IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Mar-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
VCA810AIDR
SOIC
D
8
2500
367.0
367.0
35.0
VCA810IDR
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated