ATMEL AT34C02BU3-10UU-1.7

Features
• Permanent and Reversible Software Write Protection for the First-half of the Array
– Software Procedure to Verify Write Protect Status
• Hardware Write Protection for the Entire Array
• Low-voltage and Standard-voltage Operation
– 1.7 (VCC = 1.7V to 3.6V)
Internally Organized 256 x 8
Two-wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
100 kHz (1.7V) and 400 kHz (2.7V and 3.6V) Compatibility
16-byte Page Write Modes
Partial Page Writes Are Allowed
Self-timed Write Cycle (5 ms max)
High-reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
• 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini-MAP (MLP 2x3), 8-lead TSSOP, and 8-ball
dBGA2 Packages
•
•
•
•
•
•
•
•
•
Description
The AT34C02B provides 2048 bits of serial electrically-erasable and programmable
read only memory (EEPROM) organized as 256 words of 8 bits each. The first-half of
the device incorporates a permanent and a reversible software write protection feature
while hardware write protection for the entire array is available via an external pin.
Once the permanent software write protection is enabled, by sending a special command to the device, it cannot be reversed. However, the reversible software write
protection is enabled and can be reversed by sending a special command. The hardware write protection is controlled with the WP pin and can be used to protect the
entire array, whether or not the software write protection has been enabled. This
allows the user to protect none, first-half, or all of the array depending on the application. The device is optimized for use in many industrial and commercial applications
where low-power and low-voltage operations are essential. The AT34C02B is available in space saving 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini-MAP (MLP 2x3), 8-lead
TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface.
It is available in 1.7V (1.7V to 3.6V).
8-ball dBGA2
Table 1. Pin Configurations
Pin Name
Function
VCC
WP
SCL
SDA
A0 - A2
Address Inputs
SDA
Serial Data
SCL
Serial Clock Input
WP
8
1
7
2
6
3
5
4
A0
A1
A2
GND
1
2
3
4
8
7
6
5
AT34C02B
Note:
Not recommended for new
design; please refer to
AT34C02C datasheet.
VCC
WP
SCL
SDA
8
7
6
5
1
2
3
4
A0
A1
A2
GND
(MLP 2x3)
Bottom View
8-lead SOIC
8-lead TSSOP
A0
A1
A2
GND
2K (256 x 8)
8-lead Ultra Thin Mini-MAP
Bottom View
Write Protect
Two-wire Serial
EEPROM
with Permanent
and Reversible
Software Write
Protect
VCC
WP
SCL
SDA
A0
A1
A2
GND
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
Rev. 3417E–SEEPR–1/07
1
Absolute Maximum Ratings*
Operating Temperature..................................–55°C to +125 °C
*NOTICE:
Storage Temperature .....................................–65°C to +150°C
Voltage on Any Pin
with Respect to Ground .................................... –1.0V to +7.0V
Maximum Operating Voltage .......................................... 6.25V
DC Output Current........................................................ 5.0 mA
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Figure 1. Block Diagram
VCC
GND
WP
START
STOP
LOGIC
SCL
SDA
SERIAL
CONTROL
LOGIC
WRITE PROTECT
CIRCUITRY
EN
H.V. PUMP/TIMING
LOAD
A2
A1
A0
R/W
COMP
LOAD
DATA WORD
ADDR/COUNTER
DATA RECOVERY
SOFTWARE WRITE
PROTECTED AREA
(00H - 7FH)
INC
X DEC
DEVICE
ADDRESS
COMPARATOR
EEPROM
Y DEC
DIN
SERIAL MUX
DOUT/ACK
LOGIC
DOUT
2
AT34C02B
3417E–SEEPR–1/07
AT34C02B
Pin Description
SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each
EEPROM device and negative edge clock data out of each device.
SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is
open-drain driven and may be wire-ORed with any number of other open-drain or open
collector devices.
DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device
address inputs that are hardwired (directly to GND or to Vcc) for compatibility with other
AT24Cxx devices. When the pins are hardwired, as many as eight 2K devices may be
addressed on a single bus system. (Device addressing is discussed in detail under
“Device Addressing,” page 9.) A device is selected when a corresponding hardware and
software match is true. If these pins are left floating, the A2, A1, and A0 pins will be
internally pulled down to GND. However, due to capacitive coupling that may appear
during customer applications, Atmel recommends always connecting the address pins
to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less.
WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to Vcc, all write operations to the
memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down
to GND. However, due to capacitive coupling that may appear during customer applications, Atmel recommends always connecting the WP pins to a known state. When using
a pull-up resistor, Atmel recommends using 10kΩ or less.
Table 2. AT34C02B Write Protection Modes
WP Pin Status
Permanent Write Protect
Register
Reversible Write Protect
Register
Part of the Array Write
Protected
VCC
–
–
Full Array (2K)
GND or Floating
Not Programmed
Not Programmed
Normal Read/Write
GND or Floating
Programmed
–
First-Half of Array
(1K: 00H - 7FH)
GND or Floating
–
Programmed
First-Half of Array
(1K: 00H - 7FH)
Table 3. Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 100 kHz, VCC = +1.7V
Symbol
Test Condition
CI/O
CIN
Note:
Max
Units
Conditions
Input/Output Capacitance (SDA)
8
pF
VI/O = 0V
Input Capacitance (A0, A1, A2, SCL)
6
pF
VIN = 0V
1. This parameter is characterized and is not 100% tested.
3
3417E–SEEPR–1/07
Table 4. DC Characteristics
Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +1.7V to +3.6V, (unless otherwise noted)
Symbol
Parameter
Test Condition
VCC1
Supply Voltage
ICC
Supply Current VCC = 3.6V
READ at 100 kHz
ICC
Supply Current VCC = 3.6V
ISB1
Min
Typ
Max
Units
3.6
V
0.4
1.0
mA
WRITE at 100 kHz
2.0
3.0
mA
Standby Current VCC = 1.7V
VIN = VCC or VSS
0.6
3.0
µA
ISB2
Standby Current VCC = 3.6V
VIN = VCC or VSS
1.6
4.0
µA
ILI
Input Leakage Current
VIN = VCC or VSS
0.10
3.0
µA
ILO
Output Leakage Current
VOUT = VCC or VSS
0.05
3.0
µA
VIL
Input Low Level(1)
–0.6
VCC x 0.3
V
VCC x 0.7
VCC + 0.5
V
1.7
(1)
VIH
Input High Level
VOL2
Output Low Level VCC = 3.0V
IOL = 2.1 mA
0.4
V
Output Low Level VCC = 1.7V
IOL = 0.15 mA
0.2
V
VOL1
Note:
4
1. VIL min and VIH max are reference only and are not tested.
AT34C02B
3417E–SEEPR–1/07
AT34C02B
Table 5. AC Characteristics
Applicable over recommended operating range from TAI = –40°C to +85°C, VCC = +1.7V to +3.6V, CL = 1 TTL Gate and
100 pF (unless otherwise noted)
1.7V
Symbol
Parameter
Min
fSCL
Clock Frequency, SCL
tLOW
Clock Pulse Width Low
tHIGH
Clock Pulse Width High
2.7V, 3.6V
Max
Min
100
Max
Units
400
kHz
4.7
1.2
µs
4.0
0.6
µs
(1)
tI
Noise Suppression Time
tAA
Clock Low to Data Out Valid
0.1
tBUF
Time the bus must be free before a new
transmission can start(1)
4.7
1.2
µs
tHD.STA
Start Hold Time
4.0
0.6
µs
tSU.STA
Start Set-up Time
4.7
0.6
µs
tHD.DAT
Data In Hold Time
0
0
µs
tSU.DAT
Data In Set-up Time
200
100
ns
100
(1)
Inputs Rise Time
tR
(1)
4.5
0.1
50
ns
0.9
µs
1.0
0.3
µs
300
300
ns
tF
Inputs Fall Time
tSU.STO
Stop Set-up Time
4.7
0.6
µs
tDH
Data Out Hold Time
100
50
ns
tWR
Write Cycle Time
Endurance(1)
25°C, Page Mode
Note:
5
1M
5
1M
ms
Write
Cycles
1. This parameter is characterized and is not 100% tested.
5
3417E–SEEPR–1/07
Memory Organization
AT34C02B, 2K Serial EEPROM: The 2K is internally organized with 16 pages of 16
bytes each. Random word addressing requires a 8-bit data word address.
Device Operation
CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see
Figure 4 on page 7). Data changes during SCL high periods will indicate a start or stop
condition as defined below.
START CONDITION: A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command (see Figure 5 on page 8).
STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition.
After a read sequence, the stop command will place the EEPROM in a standby power
mode (see Figure 5 on page 8).
ACKNOWLEDGE: All addresses and data words are serially transmitted to and from
the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has
received each word. This happens during the ninth clock cycle.
STANDBY MODE: The AT34C02B features a low-power standby mode which is
enabled: (a) upon power-up or (b) after the receipt of the STOP bit and the completion of
any internal operations.
MEMORY RESET: After an interruption in protocol, power loss or system reset, any
Two-wire part can be reset by following these steps:
(a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then
(c) create a start condition.
6
AT34C02B
3417E–SEEPR–1/07
AT34C02B
Figure 2. Bus Timing SCL: Serial Clock SDA: Serial Data I/O
Figure 3. Write Cycle Timing SCL: Serial Clock SDA: Serial Data I/O
SCL
SDA
8th BIT
ACK
WORDn
(1)
twr
STOP
CONDITION
Note:
START
CONDITION
1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle.
Figure 4. Data Validity
7
3417E–SEEPR–1/07
Figure 5. Start and Stop Condition
Figure 6. Output Acknowledge
8
AT34C02B
3417E–SEEPR–1/07
AT34C02B
Device Addressing
The 2K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (see Figure 10 on page 13).
The device address word consists of a mandatory one-zero sequence for the first four
most-significant bits (1010) for normal read and write operations and 0110 for writing to
the write protect register.
The next 3 bits are the A2, A1 and A0 device address bits for the AT34C02B EEPROM.
These 3 bits must compare to their corresponding hard-wired input pins.
The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is
not made, the chip will return to a standby state. The device will not acknowledge if the
write protect register has been programmed and the control code is 0110.
Write Operations
BYTE WRITE: A write operation requires an 8-bit data word address following the
device address word and acknowledgment. Upon receipt of this address, the EEPROM
will again respond with a zero and then clock in the first 8-bit data word. Following
receipt of the 8-bit data word, the EEPROM will output a zero and the addressing
device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR , to the
nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will
not respond until the write is complete (see Figure 11 on page 13).
The device will acknowledge a write command, but not write the data, if the software or
hardware write protection has been enabled. The write cycle time must be observed
even when the write protection is enabled.
PAGE WRITE: The 2K device is capable of 16-byte page write.
A page write is initiated the same as a byte write, but the microcontroller does not send
a stop condition after the first data word is clocked in. Instead, after the EEPROM
acknowledges receipt of the first data word, the microcontroller can transmit up to fifteen
more data words. The EEPROM will respond with a zero after each data word received.
The microcontroller must terminate the page write sequence with a stop condition (see
Figure 12 on page 14).
The data word address lower four bits are internally incremented following the receipt of
each data word. The higher data word address bits are not incremented, retaining the
memory page row location. When the word address, internally generated, reaches the
page boundary, the following byte is placed at the beginning of the same page. If more
than sixteen data words are transmitted to the EEPROM, the data word address will “roll
over” and previous data will be overwritten. The address “roll over” during write is from
the last byte of the current page to the first byte of the same page.
The device will acknowledge a write command, but not write the data, if the software or
hardware write protection has been enabled. The write cycle time must be observed
even when the write protection is enabled.
ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the
EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is
representative of the operation desired. Only if the internal write cycle has completed
will the EEPROM respond with a zero allowing the read or write sequence to continue.
9
3417E–SEEPR–1/07
Write Protection
The software write protection, once enabled, write protects only the first-half of the array
(00H - 7FH) while the hardware write protection, via the WP pin, is used to protect the
entire array.
PERMANENT SOFTWARE WRITE PROTECTION: The software write protection is
enabled by sending a command, similar to a normal write command, to the device which
programs the permanent write protect register. This must be done with the WP pin low.
The write protect register is programmed by sending a write command with the device
address of 0110 instead of 1010 with the address and data bit being don’t cares (see
Figure 7 on page 10). Once the software write protection has been enabled, the device
will no longer acknowledge the 0110 control byte. The software write protection cannot
be reversed even if the device is powered down. The write cycle time must be observed.
REVERSIBLE SOFTWARE WRITE PROTECTION: The reversible software write protection is enabled by sending a command, similar to a normal write command, to the
device which programs the reversible write protect register. This must be done with the
WP pin low. The write protect register is programmed by sending a write command
01100010 with pins A2 and A1 tied to ground or don't connect and pin A0 connected to
VHV (see Figure 8). The reversible write protection can be reversed by sending a command 01100110 with pin A2 tied to ground or no connect, pin A1 tied to VCC and pin A0
tied to VHV (see Figure 9).
HARDWARE WRITE PROTECTION: The WP pin can be connected to VCC, GND, or
left floating. Connecting the WP pin to VCC will write protect the entire array, regardless
of whether or not the software write protection has been enabled. The software write
protection register cannot be programmed when the WP pin is connected to VCC. If the
WP pin is connected to GND or left floating, the write protection mode is determined by
the status of the software write protect register.
Figure 7. Setting Permanent Write Protect Register (PSWP)
S
T
A
R
T
SDA LINE
CONTROL
BYTE
WORD
ADDRESS
S
T
O
P
DATA
0 1 1 0 A2 A1 A0 0
A
C
K
A
C
K
A
C
K
= Don't Care
Figure 8. Setting Reversible Write Protect Register (RSWP)
S
T
A
R
T
SDA LINE
CONTROL
BYTE
WORD
ADDRESS
S
T
O
P
DATA
0 1 1 0 0 0 1 0
A
C
K
A
C
K
A
C
K
= Don't Care
Figure 9. Clearing Reversible Write Protect Register (RSWP)
S
T
A
R
T
SDA LINE
CONTROL
BYTE
WORD
ADDRESS
S
T
O
P
DATA
0 1 1 0 0 1 1 0
A
C
K
A
C
K
A
C
K
= Don't Care
10
AT34C02B
3417E–SEEPR–1/07
AT34C02B
Table 6. Write Protection
Pin
Preamble
RW
Command
A2
A1
A0
B7
B6
B5
B4
B3
B2
B1
B0
Set PSWP
A2
A1
A0
0
1
1
0
A2
A1
A0
0
Set RSWP
0
0
VHV
0
1
1
0
0
0
1
0
Clear RSWP
0
1
VHV
0
1
1
0
0
1
1
0
Table 7. VHV
VHV
Note:
Min
Max
Units
7
10
V
VHV - VCC > 4.8V
Table 8. WP Connected to GND or Floating
WP Connected to GND or Floating
Reversible Write
Protect Register
RSWP
Acknowledgment
from Device
Command
R/W Bit
Permanent Write
Protect Register
PSWP
1010
R
X
X
ACK
1010
W
Programmed
X
ACK
Can write to second Half (80H - FFH) only
1010
W
X
Programmed
ACK
Can write to second Half (80H - FFH) only
1010
W
Not Programmed
Not Programmed
ACK
Can write to full array
Read PSWP
R
Programmed
X
No ACK
STOP - Indicates permanent write protect register is
programmed
Read PSWP
R
Not Programmed
X
ACK
Read out data don't care. Indicates PSWP register
is not programmed
Set PSWP
W
Programmed
X
No ACK
STOP - Indicates permanent write protect register is
programmed
Set PSWP
W
Not Programmed
X
ACK
Read RSWP
R
X
Programmed
No ACK
STOP - Indicates reversible write protect register is
programmed
Read RSWP
R
X
Not Programmed
ACK
Read out data don't care. Indicates RSWP register
is not programmed
Set RSWP
W
X
Programmed
No ACK
STOP - Indicates reversible write protect register is
programmed
Set RSWP
W
X
Not Programmed
ACK
Program reversible write protect register (reversible)
Clear RSWP
W
Programmed
X
No ACK
STOP - Indicates permanent write protect register is
programmed
Clear RSWP
W
Not Programmed
X
ACK
Action from Device
Program permanent write protect register
(irreversible)
Clear (unprogram) reversible write protect register
(reversible)
11
3417E–SEEPR–1/07
Table 9. WP Connected to Vcc
WP Connected to Vcc
Reversible Write
Protect Register
RSWP
Acknowledgment
from Device
Command
R/W Bit
Permanent Write
Protect Register
PSWP
1010
R
X
X
ACK
Read array
1010
W
X
X
ACK
Device Write Protect
Read
PSWP
R
Programmed
X
No ACK
STOP - Indicates permanent write protect register is
programmed
Read
PSWP
R
Not Programmed
X
ACK
Read out data don't care. Indicates PSWP register is
not programmed
Set PSWP
W
Programmed
X
No ACK
STOP - Indicates permanent write protect register is
programmed
Set PSWP
W
Not Programmed
X
ACK
Read
RSWP
R
X
Programmed
No ACK
Read
RSWP
R
X
Not Programmed
ACK
Set RSWP
W
X
Programmed
No ACK
Set RSWP
W
X
Not Programmed
ACK
Clear
RSWP
W
Programmed
X
No ACK
Clear
RSWP
W
Not Programmed
X
ACK
Read Operations
Action from Device
Cannot program write protect registers
STOP - Indicates reversible write protect register is
programmed
Read out data don't care. Indicates RSWP register is
not programmed
STOP - Indicates reversible write protect register is
programmed
Cannot program write protect registers
STOP - Indicates permanent write protect register is
programmed
Cannot write to write protect registers
Read operations are initiated the same way as write operations with the exception that
the read/write select bit in the device address word is set to one. There are three read
operations: current address read, random address read and sequential read.
CURRENT ADDRESS READ: The internal data word address counter maintains the
last address accessed during the last read or write operation, incremented by one. This
address stays valid between operations as long as the chip power is maintained. The
address “roll over” during read is from the last byte of the last memory page to the first
byte of the first page.
Once the device address with the read/write select bit set to one is clocked in and
acknowledged by the EEPROM, the current address data word is serially clocked out.
To end the command, the microcontroller does not respond with an input zero but does
generate a following stop condition (see Figure 13 on page 14).
RANDOM READ: A random read requires a “dummy” byte write sequence to load in the
data word address. Once the device address word and data word address are clocked
in and acknowledged by the EEPROM, the microcontroller must generate another start
condition. The microcontroller now initiates a current address read by sending a device
address with the read/write select bit high. The EEPROM acknowledges the device
address and serially clocks out the data word. To end the command, the microcontroller
12
AT34C02B
3417E–SEEPR–1/07
AT34C02B
does not respond with a zero but does generate a following stop condition (see Figure
14 on page 14).
SEQUENTIAL READ: Sequential reads are initiated by either a current address read or
a random address read. After the microcontroller receives a data word, it responds with
an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to
increment the data word address and serially clock out sequential data words. When the
memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the
microcontroller does not respond with a zero but does generate a following stop condition (see Figure 15 on page 14).
PERMANENT WRITE PROTECT REGISTER (PSWP) STATUS: To find out if the register has been programmed, the same procedure is used as to program the register
except that the R/W bit is set to 1. If the device sends an acknowledge, then the permanent write protect register has not been programmed. Otherwise, it has been
programmed and the device is permanently write protected at the first half of the array.
Table 10. PSWP Status
Pin
Preamble
RW
Command
A2
A1
A0
B7
B6
B5
B4
B3
B2
B1
B0
Read PSWP
A2
A1
A0
0
1
1
0
A2
A1
A0
1
REVERSIBLE WRITE PROTECT REGISTER(RSWP) STATUS: To find out if the register has been programmed, the same procedure is used as to program the register
except that the R/W bit is set to 1. If the sends an device acknowledge, then the reversible write protect register has not been programmed. Otherwise, it has been
programmed and the device is write protected (reversible) at the first half of the array.
Figure 10. Device Address
Figure 11. Byte Write
13
3417E–SEEPR–1/07
Figure 12. Page Write
Figure 13. Current Address Read
Figure 14. Random Read
Figure 15. Sequential Read
14
AT34C02B
3417E–SEEPR–1/07
AT34C02B
AT34C02B Ordering Information(1)
Ordering Code
AT34C02BN-10SU-1.7(2)
AT34C02B-10TU-1.7(2)
AT34C02BY6-10YH-1.7(3)
AT34C02BU3-10UU-1.7(2)
Notes:
Package
Operation Range
8S1
8A2
8Y6
8U3-1
Lead-free/Halogen-free/
Industrial Temperature
(–40°C to 85°C)
1. Not Recommended for new design; Please refer to AT34C02C datasheet.
2. “U” designates Green package + RoHS compliant.
3. “H” designates Green package + RoHS compliant, with NiPdAu Lead Finish.
Package Type
8S1
8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)
8A2
8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP)
8Y6
8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (DFN), (MLP 2x3 mm)
8U3-1
8-ball, die Ball Grid Array Package (dBGA2)
Options
–1.7
Low Voltage (1.7V to 3.6V)
15
3417E–SEEPR–1/07
Packaging Information
8S1 – JEDEC SOIC
C
1
E
E1
L
N
∅
Top View
End View
e
B
COMMON DIMENSIONS
(Unit of Measure = mm)
A
A1
D
Side View
SYMBOL
MIN
NOM
MAX
A
1.35
–
1.75
A1
0.10
–
0.25
b
0.31
–
0.51
C
0.17
–
0.25
D
4.80
–
5.00
E1
3.81
–
3.99
E
5.79
–
6.20
e
NOTE
1.27 BSC
L
0.40
–
1.27
∅
0˚
–
8˚
Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.
10/7/03
R
16
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TITLE
8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
DRAWING NO.
8S1
REV.
B
AT34C02B
3417E–SEEPR–1/07
AT34C02B
8A2 – TSSOP
3
2 1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
A
b
D
MIN
NOM
MAX
NOTE
2.90
3.00
3.10
2, 5
3, 5
E
e
D
A2
6.40 BSC
E1
4.30
4.40
4.50
A
–
–
1.20
A2
0.80
1.00
1.05
b
0.19
–
0.30
e
Side View
L
0.65 BSC
0.45
L1
Notes:
4
0.60
0.75
1.00 REF
1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances,
datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15 mm (0.006 in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm
(0.010 in) per side.
4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the
b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between
protrusion and adjacent lead is 0.07 mm.
5. Dimension D and E1 to be determined at Datum Plane H.
5/30/02
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
8A2, 8-lead, 4.4 mm Body, Plastic
Thin Shrink Small Outline Package (TSSOP)
DRAWING NO.
8A2
REV.
B
17
3417E–SEEPR–1/07
8Y6 – Mini-MAP
D2
A
b
(8X)
E
E2
Pin 1
Index
Area
Pin 1 ID
L (8X)
D
A2
e (6X)
A1
1.50 REF.
A3
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
2.00 BSC
E
3.00 BSC
MAX
D2
1.40
1.50
1.60
E2
-
-
1.40
A
-
-
0.60
A1
0.0
0.02
0.05
A2
-
-
0.55
A3
L
b
NOTE
0.20 REF
0.20
e
Notes:
NOM
D
0.30
0.40
0.50 BSC
0.20
0.25
0.30
2
1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions,
tolerances, datums, etc.
2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the
terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area.
8/26/05
R
18
2325 Orchard Parkway
San Jose, CA 95131
DRAWING NO.
TITLE
8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map,
8Y6
Dual No Lead Package (DFN) ,(MLP 2x3)
REV.
C
AT34C02B
3417E–SEEPR–1/07
AT34C02B
8U3-1 – dBGA2
E
D
1.
b
A1
PIN 1 BALL PAD CORNER
A2
Top View
A
Side View
PIN 1 BALL PAD CORNER
1
2
3
4
8
7
6
5
(d1)
d
e
COMMON DIMENSIONS
(Unit of Measure = mm)
(e1)
Bottom View
8 SOLDER BALLS
1. This drawing is for general information only.
2. Dimension ‘b’ is measured at maximum solder ball diameter
SYMBOL
MIN
NOM
MAX
A
0.71
0.81
0.91
A1
0.10
0.15
0.20
A2
0.40
0.45
0.50
b
0.20
0.25
0.30
D
1.50 BSC
E
2.00 BSC
e
0.50 BSC
e1
0.25 REF
d
1.00 BSC
d1
0.25 REF
NOTE
2
6/24/03
R
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TITLE
8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch,
Small Die Ball Grid Array Package (dBGA2)
DRAWING NO.
REV.
PO8U3-1
A
19
3417E–SEEPR–1/07
Revision History
20
Doc. Rev.
Date
Comments
3417E
1/2007
Revision History Implemented.
Pg 1: Added note: Not Recommended for new design; Please
refer to AT34C02C datasheet.
AT34C02B
3417E–SEEPR–1/07
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life
©2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered
trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
3417E–SEEPR–1/07