ARINC 600 Backshells 527-025 Strain Relief Backshell for Size 2 ARINC 600 Series Connectors 527-025 NF P1 A08 C12 D12 T S S = Safety Wire Holes on Hex Locknuts, Omit For None Basic Part No. Finish (Table II) Termination Style (Note 2) D = 2 Ring, T = 3 Ring Connector Designator (Table III) Entry Location (A, B, C, D, E, F, G, H, J, K, L) and Dash No. (Table I), 3 Entry Combinations Max 2.54 (64.5) Max 1.79 (45.5) 1.082 (27.5) 1.067 (27.1) 2.09 (53.1) “L” Entry “A” Entry “K” Entry “D” Entry 5.355 (136.0) 5.345 (135.8) A “B” Entry 3.770 (95.8) 3.760 (95.5) “E” Entry “J” Entry 3 Ring Term. Shown (Note 2) “C” Entry 2.004 (50.9) 1.994 (50.6) 1.258 (32.0) 1.248 (31.7) “F” Entry “H” Entry 5.61 (142.5) Cable Range Typ. B Typ. .125 (3.2) Dia 10 Places .168 (4.3) .158 (4.0) Typ. “G” Entry 2 Ring Term. Shown (Note 2) 1.415 (35.9) 1.405 (35.7) Metric dimensions (mm) are indicated in parentheses. © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-6 ARINC 600 Backshells 527-025 Strain Relief Backshell for Size 2 ARINC 600 Series Connectors TABLE I: CABLE ENTRY Dash No. 03 04 06 08 10 12 16 A Max .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) .760 (19.3) 1.073 (27.3) TABLE II: FINISH OPTIONS Cable Range Min Max .157 (4.0) .250 (6.4) .187 (4.7) .312 (7.9) .281 (7.1) .437 (11.1) .344 (8.7) .562 (14.3) .375 (9.5) .625 (15.9) .438 (11.1) .750 (19.1) .562 (14.3) .938 (23.8) B Max .844 (21.4) .906 (23.0) 1.093 (27.8) 1.187 (30.1) 1.281 (32.5) 1.500 (38.1) 1.719 (43.7) Symbol B C* G* J LF M N Finish Symbol Finish Cadmium Plate/Olive Drab NC Zinc Cobalt/Dark Olive Drab Black Anodize NF Cadmium Plate/Olive Drab over Anodic Hard Coat Electroless Nickel Gold Iridite over Cadmium Plate T Cadmium Plate/Bright over over Electroless Nickel Electroless Nickel Cadmium Plate/Bright over U** Cadmium Plate/Black Electroless Nickel ZN Zinc-Nickel Alloy/Olive Drab *Anodize finish is not suitable for EMI shielding or grounding Electroless Nickel Cadmium Plate/Olive Drab over applications. **Applicable to corrosion resisting steel backshells and Electroless Nickel accessories. Consult factory for other available finishes. TABLE III: CONNECTOR DESIGNATOR ARINC 600 series connector backshells are designed to replace the insert retainer plates. Due to non-standard modifications by the connector manufacturer, the backshell may require special design alterations to mate properly. The following should be used to determine if a backshell modification is required. Prior to ordering, consult factory with connector part numbers not shown to ensure a proper fit. Connector Designator Connector Description P All Manufacturer’s Plug and Receptacle Shells, Except for Those Listed Below (Prior to ordering, consult factory with connector part numbers not listed below to ensure a proper fit.) P1 P2 Cannon BKAD****322 Series Plug P3 Cannon/Boeing BACC 66 Plug P5 Radiall/Boeing BACC66 Plug P6 Cannon BKAC & BKAE XXX322 Series Environmental Plug Cannon/Radiall Environmental Plug 1. Metric dimensions (mm) are indicated in parentheses. 2. Designate Symbol “T” (3 ring termination) for termination of individual and overall braid. Designate symbol “D” (2 ring termination) for termination of individual or overall braid. 3. Material/Finish: Backshell, Nuts, Clamps, Ferrule = Al Alloy/See Table II Hardware = SST/Passivate © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-7