CY621472E30 MoBL® 4-Mbit (256 K × 16) Static RAM 4-Mbit (256 K × 16) Static RAM Features reduces power consumption when addresses are not toggling. Placing the device into standby mode reduces power consumption by more than 99 percent when deselected (CE1 HIGH or CE2 LOW or both BLE and BHE are HIGH). The input and output pins (I/O0 through I/O15) are placed in a high impedance state when: Very high speed: 45 ns Temperature range ❐ Industrial: –40 °C to +85 °C ■ Wide voltage range: 2.20 V to 3.60 V ■ Ultra low standby power ❐ Typical standby current: 1 A ❐ Maximum standby current: 7 A (Industrial) ■ Ultra low active power ❐ Typical active current: 2 mA at f = 1 MHz ■ Easy memory expansion with CE1, CE2, and OE Features ■ ■ ■ Automatic power down when deselected ■ Complementary metal oxide semiconductor (CMOS) for optimum speed and power ■ Available in Pb-free 44-pin thin small outline package (TSOP) II package ■ Byte power down feature ■ Deselected (CE1 HIGH or CE2 LOW) ■ Outputs are disabled (OE HIGH) ■ Both Byte High Enable and Byte Low Enable are disabled (BHE, BLE HIGH) ■ Write operation is active (CE1 LOW and CE2 HIGH and WE LOW) To write to the device, take Chip Enable (CE1 LOW and CE2 HIGH) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O0 through I/O7) is written into the location specified on the address pins (A0 through A17). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O8 through I/O15) is written into the location specified on the address pins (A0 through A17). To read from the device, take Chip Enable (CE1 LOW and CE2 HIGH and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins appear on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from memory appears on I/O8 to I/O15. See the Truth Table on page 11 for a complete description of read and write modes. For a complete list of related documentation, click here. Functional Description The CY621472E30 is a high performance CMOS static RAM (SRAM) organized as 256K words by 16 bits. This device features advanced circuit design to provide ultra low active current. It is ideal for providing More Battery Life™ (MoBL) in portable applications such as cellular telephones. The device also has an automatic power down feature that significantly Logic Block Diagram SENSE AMPS ROW DECODER DATA IN DRIVERS A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 256K x 16 RAM Array I/O0–I/O7 I/O8–I/O15 COLUMN DECODER A17 A15 A16 A13 A14 A12 BHE BLE CIRCUIT A11 CE POWER DOWN BHE WE CE1 CE2 OE BLE Cypress Semiconductor Corporation Document Number: 001-67798 Rev. *F • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised November 18, 2014 CY621472E30 MoBL® Contents Product Portfolio .............................................................. 3 Pin Configuration ............................................................. 3 Maximum Ratings ............................................................. 4 Operating Range ............................................................... 4 Electrical Characteristics ................................................. 4 Capacitance ...................................................................... 5 Thermal Resistance .......................................................... 5 AC Test Loads and Waveforms ....................................... 5 Data Retention Characteristics ....................................... 6 Data Retention Waveform ................................................ 6 Switching Characteristics ................................................ 7 Switching Waveforms ...................................................... 8 Truth Table ...................................................................... 11 Document Number: 001-67798 Rev. *F Ordering Information ...................................................... 12 Ordering Code Definitions ......................................... 12 Package Diagram ............................................................ 13 Acronyms ........................................................................ 14 Document Conventions ................................................. 14 Units of Measure ....................................................... 14 Document History Page ................................................. 15 Sales, Solutions, and Legal Information ...................... 16 Worldwide Sales and Design Support ....................... 16 Products .................................................................... 16 PSoC® Solutions ...................................................... 16 Cypress Developer Community ................................. 16 Technical Support ..................................................... 16 Page 2 of 16 CY621472E30 MoBL® Product Portfolio Power Dissipation Product CY621472E30LL Range Industrial VCC Range (V) Min Typ [1] Max 2.2 3.0 3.6 Speed (ns) 45 Operating ICC (mA) f = 1 MHz f = fmax Standby ISB2 (A) Typ [1] Max Typ [1] Max Typ [1] Max 2 2.5 15 20 1 7 Pin Configuration Figure 1. 44-pin TSOP II pinout A4 A3 A2 A1 A0 CE1 I/O0 I/O1 I/O2 I/O3 VCC VSS I/O4 I/O5 I/O6 I/O7 WE A17 A16 A15 A14 A13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE BHE BLE I/O15 I/O14 I/O13 I/O12 VSS VCC I/O11 I/O10 I/O9 I/O8 CE2 A8 A9 A10 A11 A12 Note 1. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. Document Number: 001-67798 Rev. *F Page 3 of 16 CY621472E30 MoBL® DC input voltage [2, 3] ......... –0.3 V to 3.9 V (VCCmax + 0.3 V) Maximum Ratings Output current into outputs (LOW) ............................. 20 mA Exceeding the maximum ratings may impair the useful life of the device. User guidelines are not tested. Static discharge voltage (MIL-STD-883, Method 3015) ................................ > 2001 V Storage temperature ................................ –65 °C to +150 °C Latch up current...................................................... > 200 mA Ambient temperature with power applied .......................................... –55 °C to +125 °C Operating Range Supply voltage to ground potential ...........................–0.3 V to +3.9 V (VCCmax + 0.3 V) DC Voltage Applied to Outputs in High Z State [2, 3] ............ –0.3 V to 3.9 V (VCCmax + 0.3 V) Device Range Ambient Temperature VCC [4] CY621472E30LL Industrial –40 °C to +85 °C 2.2 V to 3.6 V Electrical Characteristics Over the Operating Range Parameter VOH VOL VIH VIL Description Output HIGH voltage Output LOW voltage Input HIGH voltage Input LOW voltage Test Conditions 45 ns Unit Min Typ [5] Max IOH = –0.1 mA 2.0 – – V IOH = –1.0 mA, VCC > 2.70 V 2.4 – – V IOL = 0.1 mA – – 0.4 V IOL = 2.1 mA, VCC = 2.70 V – – 0.4 V VCC = 2.2 V to 2.7 V 1.8 – VCC + 0.3 V VCC = 2.7 V to 3.6 V 2.2 – VCC + 0.3 V VCC = 2.2 V to 2.7 V –0.3 – 0.6 V VCC= 2.7 V to 3.6 V –0.3 – 0.8 V IIX Input leakage current GND < VI < VCC –1 – +1 A IOZ Output leakage current GND < VO < VCC, Output Disabled –1 – +1 A ICC VCC operating supply current f = fmax = 1/tRC – 15 20 mA – 2 2.5 – 1 7 A – 1 7 A f = 1 MHz ISB1 [6] Automatic CE power-down current – CMOS inputs VCC = VCC(max) IOUT = 0 mA CMOS levels CE1 > VCC – 0.2 V, CE2 0.2 V, VIN > VCC – 0.2 V, VIN < 0.2 V, f = fmax (address and data only), f = 0 (OE, BHE, BLE and WE), VCC = 3.60 V ISB2 [6] Automatic CE Power down current – CMOS inputs CE1 > VCC – 0.2 V or CE2 < 0.2 V or (BHE and BLE) > VCC – 0.2 V, VIN > VCC – 0.2 V or VIN < 0.2 V, f = 0, VCC = 3.60 V Notes 2. VIL(min) = –2.0 V for pulse durations less than 20 ns. 3. VIH(max) = VCC + 0.75 V for pulse durations less than 20 ns. 4. Full device AC operation assumes a minimum of 100 s ramp time from 0 to VCC(min) and 200 s wait time after VCC stabilization. 5. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. 6. Chip enables (CE1 and CE2) need to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating. Document Number: 001-67798 Rev. *F Page 4 of 16 CY621472E30 MoBL® Capacitance Parameter [7] Description CIN Input capacitance COUT Output capacitance Test Conditions TA = 25 °C, f = 1 MHz, VCC = VCC(typ) Max Unit 10 pF 10 pF Thermal Resistance Parameter [7] Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) 44-pin TSOP II Unit Package Test Conditions Still Air, soldered on a 3 × 4.5 inch, two-layer printed circuit board 77 C/W 13 C/W AC Test Loads and Waveforms Figure 2. AC Test Loads and Waveforms R1 VCC OUTPUT VCC 30 pF 10% GND Rise Time = 1 V/ns R2 INCLUDING JIG AND SCOPE ALL INPUT PULSES 90% 90% 10% Fall Time = 1 V/ns Equivalent to: THEVENIN EQUIVALENT OUTPUT Parameters 2.50 V R1 R2 RTH V 3.0 V Unit 16667 1103 15385 1554 RTH 8000 645 VTH 1.20 1.75 V Note 7. Tested initially and after any design or process changes that may affect these parameters. Document Number: 001-67798 Rev. *F Page 5 of 16 CY621472E30 MoBL® Data Retention Characteristics Over the Operating Range Parameter Description VDR VCC for data retention ICCDR[9] Data retention current Conditions VCC = 1.5 V, Min Typ [8] Max Unit 1.5 – – V – 0.8 7 A CE1 > VCC – 0.2 V or CE2 < 0.2 V or (BHE and BLE) > VCC – 0.2 V, VIN > VCC – 0.2 V or VIN < 0.2 V tCDR [10] Chip deselect to data retention time 0 – – ns tR [11] Operation recovery time 45 – – ns Data Retention Waveform Figure 3. Data Retention Waveform [12, 13] DATA RETENTION MODE VCC CE or VCC(min) tCDR VDR > 1.5 V VCC(min) tR BHE.BLE Notes 8. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(typ), TA = 25 °C. 9. Chip enables (CE1 and CE2) need to be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating. 10. Tested initially and after any design or process changes that may affect these parameters. 11. Full device operation requires linear VCC ramp from VDR to VCC(min) > 100 s or stable at VCC(min) > 100 s. 12. CE refers to the internal logical combination of CE1 and CE2 such that when CE1 is LOW and CE2 is HIGH, CE is LOW. For all other cases CE is HIGH. 13. BHE.BLE is the AND of both BHE and BLE. Deselect the chip by either disabling the chip enable signals or by disabling both BHE and BLE. Document Number: 001-67798 Rev. *F Page 6 of 16 CY621472E30 MoBL® Switching Characteristics Over the Operating Range Parameter [14] Description 45 ns Min Max Unit Read Cycle tRC Read cycle time 45 – ns tAA Address to data valid – 45 ns tOHA Data hold from address change 10 – ns tACE CE1 LOW/CE2 HIGH to data valid – 45 ns tDOE OE LOW to data valid – 22 ns [15] 5 – ns – 18 ns tLZOE tHZOE OE LOW to Low Z OE HIGH to High Z [15, 16] [15] tLZCE CE1 LOW/CE2 HIGH to Low Z 10 – ns tHZCE CE1 HIGH/CE2 LOW to High Z [15, 16] – 18 ns tPU CE1 LOW/CE2 HIGH to Power-up 0 – ns tPD CE1 HIGH/CE2 LOW to Power-down – 45 ns tDBE BLE/BHE LOW to data valid – 45 ns tLZBE BLE/BHE LOW to Low Z [15, 17] 5 – ns – 18 ns tHZBE Write Cycle BLE/BHE HIGH to High Z [15, 16] [18, 19] tWC Write cycle time 45 – ns tSCE CE1 LOW/CE2 HIGH to Write End 35 – ns tAW Address setup to write end 35 – ns tHA Address hold from write end 0 – ns tSA Address setup to write start 0 – ns tPWE WE pulse width 35 – ns tBW BLE/BHE LOW to write end 35 – ns tSD Data setup to write end 25 – ns tHD Data hold from write end 0 – ns tHZWE WE LOW to High Z [15, 16] – 18 ns 10 – ns tLZWE WE HIGH to Low Z [15] Notes 14. Test conditions for all parameters other than tri-state parameters assume signal transition time of 3 ns (1 V/ns) or less, timing reference levels of VCC(typ)/2, input pulse levels of 0 to VCC(typ), and output loading of the specified IOL/IOH as shown in the Figure 2 on page 5. 15. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device. 16. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high impedance state. 17. If both byte enables are together, this value is 10 ns. 18. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE, or both = VIL. All signals must be active to initiate a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must be referenced to the edge of the signal that terminates the write. 19. The minimum write cycle pulse width for WRITE Cycle 4 (WE controlled, OE LOW) should be equal to the sum of tHZWE and tSD. Document Number: 001-67798 Rev. *F Page 7 of 16 CY621472E30 MoBL® Switching Waveforms Figure 4. Read Cycle No. 1 (Address Transition Controlled) [20, 21] tRC ADDRESS tOHA DATA OUT tAA PREVIOUS DATA VALID DATA VALID Figure 5. Read Cycle No. 2 (OE Controlled) [21, 22, 23] ADDRESS tRC CE tPD tHZCE tACE OE tHZOE tDOE tLZOE BHE/BLE tHZBE tDBE tLZBE DATA OUT HIGHIMPEDANCE HIGH IMPEDANCE DATA VALID tLZCE tPU VCC SUPPLY CURRENT 50% ICC 50% ISB Notes 20. The device is continuously selected. OE, CE = VIL, BHE, BLE, or both = VIL. 21. WE is HIGH for read cycle. 22. CE refers to the internal logical combination of CE1 and CE2 such that when CE1 is LOW and CE2 is HIGH, CE is LOW. For all other cases CE is HIGH. 23. Address valid before or similar to CE and BHE, BLE transition LOW. Document Number: 001-67798 Rev. *F Page 8 of 16 CY621472E30 MoBL® Switching Waveforms (continued) Figure 6. Write Cycle No. 1 (WE Controlled) [24, 25, 26, 27] tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tBW BHE/BLE OE DATA I/O tSD NOTE 28 tHD DATAIN tHZOE Figure 7. Write Cycle No. 2 (CE Controlled) [24, 25, 26, 27] tWC ADDRESS tSCE CE tSA tAW tHA tPWE WE tBW BHE/BLE OE tSD DATA I/O tHD DATAIN NOTE 28 tHZOE Notes 24. CE refers to the internal logical combination of CE1 and CE2 such that when CE1 is LOW and CE2 is HIGH, CE is LOW. For all other cases CE is HIGH. 25. The internal write time of the memory is defined by the overlap of WE, CE = VIL, BHE, BLE, or both = VIL. All signals must be active to initiate a write and any of these signals can terminate a write by going inactive. The data input setup and hold timing must be referenced to the edge of the signal that terminates the write. 26. Data I/O is high impedance if OE = VIH. 27. If CE goes HIGH simultaneously with WE = VIH, the output remains in a high impedance state. 28. During this period, the I/Os are in output state. Do not apply input signals. Document Number: 001-67798 Rev. *F Page 9 of 16 CY621472E30 MoBL® Switching Waveforms (continued) Figure 8. Write Cycle No. 3 (WE Controlled, OE LOW) [29, 30, 31] tWC ADDRESS tSCE CE tBW BHE/BLE tAW tHA tSA WE tPWE tSD DATA I/O NOTE 32 tHD DATAIN tLZWE tHZWE Figure 9. Write Cycle No. 4 (BHE/BLE Controlled, OE LOW) [29, 30] tWC ADDRESS CE tSCE tAW tHA tBW BHE/BLE tSA tPWE WE tHZWE DATA I/O NOTE 32 tSD tHD DATAIN tLZWE Notes 29. CE refers to the internal logical combination of CE1 and CE2 such that when CE1 is LOW and CE2 is HIGH, CE is LOW. For all other cases CE is HIGH. 30. If CE goes HIGH simultaneously with WE = VIH, the output remains in a high impedance state. 31. The minimum write cycle pulse width should be equal to the sum of tHZWE and tSD. 32. During this period, the I/Os are in output state. Do not apply input signals. Document Number: 001-67798 Rev. *F Page 10 of 16 CY621472E30 MoBL® Truth Table CE1 H CE2 I/Os Mode Power WE OE BHE BLE [33] X X X X High Z Deselect/Power-down Standby (ISB) X X[33] L X X X X High Z Deselect/Power-down Standby (ISB) [33] X X H H High Z Deselect/Power-down Standby (ISB) L H H L L L Data out (I/O0–I/O15) Read Active (ICC) L H H L H L Data out (I/O0–I/O7); I/O8–I/O15 in High Z Read Active (ICC) L H H L L H Data out (I/O8–I/O15); I/O0–I/O7 in High Z Read Active (ICC) L H H H L L High Z Output disabled Active (ICC) L H H H H L High Z Output disabled Active (ICC) L H H H L H High Z Output disabled Active (ICC) L H L X L L Data in (I/O0–I/O15) Write Active (ICC) L H L X H L Data in (I/O0–I/O7); I/O8–I/O15 in High Z Write Active (ICC) L H L X L H Data in (I/O8–I/O15); I/O0–I/O7 in High Z Write Active (ICC) [33] X X Note 33. The ‘X’ (Don’t care) state for the chip enables (CE1 and CE2) in the truth table refer to the logic state (either HIGH or LOW). Intermediate voltage levels on these pins is not permitted. Document Number: 001-67798 Rev. *F Page 11 of 16 CY621472E30 MoBL® Ordering Information Speed (ns) 45 Ordering Code CY621472E30LL-45ZSXI Package Diagram Package Type 51-85087 44-pin TSOP II (Pb-free) Operating Range Industrial Ordering Code Definitions CY 621 4 7 2 E 30 LL - 45 ZS X I Temperature Range: I = Industrial Pb-free Package Type: ZS = 44-pin TSOP II Speed Grade: 45 = 45 ns Low Power Voltage Range: 30 = 3 V Typical Process Technology: E = 90 nm Dual Chip Enable Bus Width: 7 = × 16 Density: 4 = 4-Mbit Family Code: 621 = MoBL SRAM family Company ID: CY = Cypress Document Number: 001-67798 Rev. *F Page 12 of 16 CY621472E30 MoBL® Package Diagram Figure 10. 44-pin TSOP II Package Outline, 51-85087 51-85087 *E Document Number: 001-67798 Rev. *F Page 13 of 16 CY621472E30 MoBL® Acronyms Acronym Document Conventions Description Units of Measure CMOS Complementary Metal Oxide Semiconductor I/O Input/Output °C degree Celsius OE Output Enable MHz megahertz SRAM Static Random Access Memory A microampere TSOP Thin Small Outline Package s microsecond WE Write Enable mA milliampere ns nanosecond ohm % percent pF picofarad V volt W watt Document Number: 001-67798 Rev. *F Symbol Unit of Measure Page 14 of 16 CY621472E30 MoBL® Document History Page Document Title: CY621472E30 MoBL®, 4-Mbit (256 K × 16) Static RAM Document Number: 001-67798 Rev. ECN No. Orig. of Change Submission Date ** 3184883 RAME 03/01/2011 New data sheet. *A 3223503 RAME 04/15/2011 Overline bar CE2 removed from the Truth table. Updated all notes as per template. *B 3261142 RAME 05/19/2011 Updated Switching Characteristics (corrected the Min value of tLZBE parameter). Added Ordering Information and Ordering Code Definitions. Added Acronyms and Units of Measure. *C 3365953 AJU 09/08/2011 Changed datasheet status from Preliminary to Final. Updated 44-pin TSOP II package spec. *D 3414567 TAVA 10/20/2011 Replaced CY62147EV30 with CY621472E30 through out the data sheet. *E 4331825 NILE 04/03/2014 Updated Switching Characteristics: Added Note 19 and referred the same note in “Write Cycle”. Updated Switching Waveforms: Added Note 31 and referred the same note in Figure 8. Updated Package Diagram: spec 51-85087 – Changed revision from *D to *E. Updated in new template. Completing Sunset Review. *F 4573121 NILE 11/18/2014 Added related documentation hyperlink in page 1. Document Number: 001-67798 Rev. *F Description of Change Page 15 of 16 CY621472E30 MoBL® Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Automotive Clocks & Buffers Interface Lighting & Power Control cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc Memory cypress.com/go/memory PSoC Touch Sensing cypress.com/go/psoc PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Cypress Developer Community Community | Forums | Blogs | Video | Training Technical Support cypress.com/go/support cypress.com/go/touch USB Controllers Wireless/RF psoc.cypress.com/solutions cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2011-2014. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-67798 Rev. *F Revised November 18, 2014 Page 16 of 16 MoBL is a registered trademark, and More Battery Life is a trademark of Cypress Semiconductor. All product and company names mentioned in this document are the trademarks of their respective holders.