CY3250-FLEXCABLE Mechanical Layout Drawing.pdf

rev**
23533
15.9mm [0.625"]
24.8mm [0.975"]
Top View
27.6mm [1.085"]
Bottom View
20.3mm [0.799"]
CY3250-23533
Description:
POD
56 pin QFN OCD with Hirose cable connector (P/N: DF12-5.0-20DP-0.5V-81) with
retension mechanism included.
Compatible with:
SF-QFN32A-L-02, QFN foot, 32 pin, 0.5mm pitch, 5mm body
XT-PSoC-15-20H-10-01
CY8C23033-24PVXI
threaded inserts for mounting hardware
Side View
UGA Male pin shroud
1
Page:____of
2
EA-8C23533-Q32-01 Drawing
© 2007 IRONWOOD ELECTRONICS, INC.
Tele: (800) 404-0204
www.ironwoodelectronics.com
Status: Released
3:1
Scale:___
Rev: A
Drawing: J. Glab
Date: 11/27/07
File: EA-8C23533-Q32-01 Dwg
Modified:
Tolerances: diameters ±0.03mm [±0.001”],
PCB perimeters ±0.13mm [±0.005”],
PCB thicknesses ±0.18mm [±0.007"],
pitches (from true position) ±0.08mm [±0.003"],
all other tolerances ±0.13mm [±0.005”]
unless stated otherwise. Materials and
specifications are subject to change without notice.
[+] Feedback
Strain Relief Hardware mounting directions
(627",
0.488")
If the target board can be designed to accomodate the strain relief
hardware, layout the PCB with the pattern shown on the right. The
layout shows the location of non-plated holes through the board relative
to the QFN land pattern. If holes can not be added to the target board,
the screws can be used as standoffs and sit on the top surface of the
target PCB.
(0.369",
0.398")
(-0.283",
0.398")
QFN outline
(0.00",
0.00")
19.37mm [0.763"]
0.5mm
McMaster/Carr
91185A558
24.77mm [0.975"]
Pin 1
Flex Cable
8.49mm sq. [0.334"]
To ICE Pod
5.55mm [0.218"]
Shroud ouline
(keep away area)
Pad size: 0.3mmX0.78mm
[0.012" X 0.031"]
E-pad
3.2X3.2mm
13.25mm [0.521"]
(-0.283",
-0.398")
7.91mm [0.311"]
(0.369",
-0.399")
Ø 1.78mm [Ø 0.070"]
±0.005"
(-0.627",
-0.488")
Pod outline
5.31mm
[0.209"]
27.57mm [1.085"]
4.91mm
[0.193"]
0.48mm
[0.019"]
All component
heights ±0.020"
Top View: Target Board component layout
notes:
1) Do not place components within the shroud outline unless they have a
0.035" height or less off the target board and are outside the QFN package
outline
2) All components under the POD outline must have a 0.190" height or or less
from the top of target board to avoid components on the bottom of the POD
board.
Side view: CY3250-23533QFN Pod on QFN32 foot
EA-8C23533-Q32-01 Drawing
© 2007 IRONWOOD ELECTRONICS, INC.
Tele: (800) 404-0204
www.ironwoodelectronics.com
2
Page:____of
2
Status: Released
4:1
Scale:___
Rev: A
Drawing: J. Glab
Date: 11/27/07
File: EA-8C23533-Q32-01 Dwg
Modified:
Tolerances: diameters ±0.03mm [±0.001”],
PCB perimeters ±0.13mm [±0.005”],
PCB thicknesses ±0.18mm [±0.007"],
pitches (from true position) ±0.08mm [±0.003"],
all other tolerances ±0.13mm [±0.005”]
unless stated otherwise. Materials and
specifications are subject to change without notice.
[+] Feedback