ATMEL AT52BC6402AT-85CI

Stack Module Features
•
•
•
•
64-Mbit Flash + 16-Mbit PSRAM
Power Supply of 2.7V to 3.1V
Data I/O x16
66-ball CBGA Package: 8 x 11x 1.0 mm
64-Mbit Flash Features
• 64-megabit (4M x 16) Flash Memory
• 2.7V - 3.1V Read/Write
• High Performance
•
•
•
•
•
•
•
•
•
•
•
•
– Asynchronous Access Time – 70, 85 ns
Sector Erase Architecture
– Eight 4K Word Sectors with Individual Write Lockout
– 32K Word Main Sectors with Individual Write Lockout
Typical Sector Erase Time: 32K Word Sectors – 500 ms; 4K Word Sectors – 100 ms
64M, Four Plane Organization, Permitting Concurrent Read in Any of Three Planes not
Being Programmed/Erased
– Memory Plane A: 16M of Memory Including Eight 4K Word Sectors
– Memory Plane B: 16M of Memory Consisting of 32K Word Sectors
– Memory Plane C: 16M of Memory Consisting of 32K Word Sectors
– Memory Plane D: 16M of Memory Consisting of 32K Word Sectors
Suspend/Resume Feature for Erase and Program
– Supports Reading and Programming Data from Any Sector by Suspending Erase
of a Different Sector
– Supports Reading Any Word by Suspending Programming of Any Other Word
Low-power Operation
– 30 mA Active
– 35 µA Standby
1.8V I/O Option Reduces Overall System Power
Data Polling and Toggle Bit for End of Program Detection
VPP Pin for Write Protection and Accelerated Program/Erase Operations
RESET Input for Device Initialization
Top or Bottom Boot Block Configuration Available
128-bit Protection Register
Common Flash Interface (CFI)
64-Mbit Flash,
16-Mbit PSRAM
(x16 I/O)
AT52BC6402A
AT52BC6402AT
Preliminary
16-Mbit PSRAM Features
• 16-Mbit (1M x 16)
• 2.7V to 3.1V VCC Operation
• 70 ns Access Time
Stack Module Description
The AT52BC6402A(T) consists of a 64-Mbit Flash stacked with a 16-Mbit PSRAM in a
single CBGA package.
Stack Module Memory Contents
Device
AT52BC6402A(T)
Memory Combination
Flash/PSRAM Read Access
64M Flash + 16M PSRAM
Asynchronous, Page Mode
Rev. 3441B–STKD–11/04
1
66C4 – CBGA
Top View
1
2
3
4
5
6
7
8
9
10
11
12
NC
NC
A20
A11
A15
A14
A13
A12
GND
NC
NC
NC
A16
A8
A10
A9
I/O15 PSWE I/O14
I/O7
I/O6
I/O5
NC
NC
A
B
C
I/O13
A21
WE
I/O4
D
I/O12
PSGND RESET
PSCS PSVCC VCC
E
WP
VPP
A19
LB
UB
PSOE
A18
A17
A7
NC
A5
A4
I/O10
I/O2
I/O3
I/O9
I/O8
I/O0
I/O1
A6
A3
A2
A1
PSCE1
A0
CE1
GND
OE
NC
I/O11
F
G
H
NC
NC
Pin Configurations
2
Pin Name
Function
A0 - A21
Address
I/O0 - I/O15
Data Inputs/Outputs
CE1
Flash Chip Enable
PSCE1
PSRAM Chip Enable
PSCS
PSRAM Chip Select (Deep Power-down Control – Mode Pin)
OE/PSOE
Flash Output Enable/PSRAM Output Enable
WE/PSWE
Flash Write Enable/PSRAM Write Enable
LB
Lower Byte Control (PSRAM)
UB
Upper Byte Control (PSRAM)
RESET
Flash Reset
WP
Flash Write Protect
VPP
Flash Write Protection and Power Supply for Accelerated
Program/Erase Operation
VCC/PSVCC
Flash Power Supply/PSRAM Power Supply
NC
No Connect
GND/PSGND
Device Ground/PSRAM Ground
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
64-Mbit Flash
Description
The 64-Mbit Flash memory is divided into multiple sectors and planes for erase operations. The devices can be read or reprogrammed off a single 2.7V power supply, making
them ideally suited for in-system programming.
The 64-Mbit device is divided into four memory planes. A read operation can occur in
any of the three planes which is not being programmed or erased. This concurrent operation allows improved system performance by not requiring the system to wait for a
program or erase operation to complete before a read is performed. To further increase
the flexibility of the device, it contains an Erase Suspend and Program Suspend feature.
This feature will put the erase or program on hold for any amount of time and let the user
read data from or program data to any of the remaining sectors. There is no reason to
suspend the erase or program operation if the data to be read is in another memory
plane. The end of program or erase is detected by Data Polling or toggle bit.
The VPP pin provides data protection and faster programming and erase times. When
the VPP input is below 0.8V, the program and erase functions are inhibited. When VPP is
at 1.65V or above, normal program and erase operations can be performed. With VPP at
12.0V, the program and erase operations are accelerated.
With VPP at 12V, a six-byte command (Enter Single Pulse Program Mode) to remove the
requirement of entering the three-byte program sequence is offered to further improve
programming time. After entering the six-byte code, only single pulses on the write control lines are required for writing into the device. This mode (Single Pulse Word
Program) is exited by powering down the device, by taking the RESET pin to GND or by
a high-to-low transition on the VPP input. Erase, Erase Suspend/Resume, Program Suspend/Resume and Read Reset commands will not work while in this mode; if entered
they will result in data being programmed into the device. It is not recommended that the
six-byte code reside in the software of the final product but only exist in external programming code.
Device Operation
COMMAND SEQUENCES: The device powers on in the read mode. Command
sequences are used to place the device in other operating modes such as program and
erase. After the completion of a program or an erase cycle, the device enters the read
mode. The command sequences are written by applying a low pulse on the WE input
with CE low and OE high or by applying a low-going pulse on the CE input with WE low
and OE high. The address is latched on the falling edge of the WE or CE pulse whichever occurs first. Valid data is latched on the rising edge of the WE or the CE pulse,
whichever occurs first. The addresses used in the command sequences are not affected
by entering the command sequences.
ASYNCHRONOUS READ: The 64-Mbit Flash is accessed like an EPROM. When CE
and OE are low and WE is high, the data stored at the memory location determined by
the address pins are asserted on the outputs. The outputs are put in the high impedance
state whenever CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention.
RESET: A RESET input pin is provided to ease some system applications. When
RESET is at a logic high level, the device is in its standard operating mode. A low level
on the RESET pin halts the present device operation and puts the outputs of the device
in a high-impedance state. When a high level is reasserted on the RESET pin, the
device returns to read or standby mode, depending upon the state of the control pins.
3
3441B–STKD–11/04
ERASE: Before a word can be reprogrammed it must be erased. The erased state of
the memory bits is a logical “1”. The entire memory can be erased by using the Chip
Erase command or individual planes or sectors can be erased by using the Plane Erase
or Sector Erase commands.
CHIP ERASE: Chip Erase is a six-bus cycle operation. The automatic erase begins on
the rising edge of the last WE pulse. Chip Erase does not alter the data of the protected
sectors. After the full chip erase the device will return back to the read mode. The hardware reset during Chip Erase will stop the erase but the data will be of unknown state.
Any command during Chip Erase except Erase Suspend will be ignored.
PLANE ERASE: As a alternative to a full chip erase, the device is organized into four
planes that can be individually erased. The plane erase command is a six-bus cycle
operation. The plane whose address is valid at the sixth falling edge of WE will be
erased provided none of the sectors within the plane are protected.
SECTOR ERASE: As an alternative to a full chip erase or a plane erase, the device is
organized into multiple sectors that can be individually erased. The Sector Erase command is a six-bus cycle operation. The sector whose address is valid at the sixth falling
edge of WE will be erased provided the given sector has not been protected.
WORD PROGRAMMING: The device is programmed on a word-by-word basis. Programming is accomplished via the internal device command register and is a four-bus
cycle operation. The programming address and data are latched in the fourth cycle. The
device will automatically generate the required internal programming pulses. Please
note that a “0” cannot be programmed back to a “1”; only erase operations can convert
“0”s to “1”s.
FLEXIBLE SECTOR PROTECTION: The 64-Mbit device offers two sector protection
modes, the Softlock and the Hardlock. The Softlock mode is optimized as sector protection for sectors whose content changes frequently. The Hardlock protection mode is
recommended for sectors whose content changes infrequently. Once either of these two
modes is enabled, the contents of the selected sector is read-only and cannot be erased
or programmed. Each sector can be independently programmed for either the Softlock
or Hardlock sector protection mode. At power-up and reset, all sectors have their Softlock protection mode enabled.
SOFTLOCK AND UNLOCK: The Softlock protection mode can be disabled by issuing a
two-bus cycle Unlock command to the selected sector. Once a sector is unlocked, its
contents can be erased or programmed. To enable the Softlock protection mode, a sixbus cycle Softlock command must be issued to the selected sector.
HARDLOCK AND WRITE PROTECT (WP): The Hardlock sector protection mode operates in conjunction with the Write Protection (WP) pin. The Hardlock sector protection
mode can be enabled by issuing a six-bus cycle Hardlock software command to the
selected sector. The state of the Write Protect pin affects whether the Hardlock protection mode can be overridden.
• When the WP pin is low and the Hardlock protection mode is enabled, the sector
cannot be unlocked and the contents of the sector is read-only.
• When the WP pin is high, the Hardlock protection mode is overridden and the sector
can be unlocked via the Unlock command.
To disable the Hardlock sector protection mode, the chip must be either reset or power
cycled.
4
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Table 1. Hardlock and Softlock Protection Configurations in Conjunction with WP
WP
Hardlock
Softlock
Erase/
Prog
Allowed?
VCC/5V
0
0
0
Yes
No sector is locked
VCC/5V
0
0
1
No
Sector is Softlocked. The Unlock
command can unlock the sector.
VCC/5V
0
1
1
No
Hardlock protection mode is
enabled. The sector cannot be
unlocked.
VCC/5V
1
0
0
Yes
No sector is locked.
VCC/5V
1
0
1
No
Sector is Softlocked. The Unlock
command can unlock the sector.
VCC/5V
1
1
0
Yes
Hardlock protection mode is
overridden and the sector is not
locked.
VCC/5V
1
1
1
No
Hardlock protection mode is
overridden and the sector can be
unlocked via the Unlock command.
VIL
x
x
x
No
Erase and Program Operations
cannot be performed.
VPP
Comments
Figure 1. Sector Locking State Diagram
UNLOCKED
[000]
LOCKED
A
B
[001]
C
Power-Up/Reset
Default
C
WP = VIL = 0
Hardlocked
[011]
A
[110]
B
C
WP = VIH = 1
A
[100]
Hardlocked is disabled by
WP = VIH
[111]
C
Power-Up/Reset
Default
B
[101]
A = Unlock Command
B = Softlock Command
C = Hardlock Command
Note:
1. The notation [X, Y, Z] denotes the locking state of a sector. The current locking state
of a sector is defined by the state of WP and the two bits of the sector-lock status
D[1:0].
5
3441B–STKD–11/04
SECTOR PROTECTION DETECTION: A software method is available to determine if
the sector protection Softlock or Hardlock features are enabled. When the device is in
the software product identification mode (see Software Product Identification Entry and
Exit sections) a read from the I/O0 and I/O1 at address location 00002H within a sector
will show if the sector is unlocked, softlocked, or hardlocked.
Table 2. Sector Protection Status
I/O1
I/O0
Sector Protection Status
0
0
Sector Not Locked
0
1
Softlock Enabled
1
0
Hardlock Enabled
1
1
Both Hardlock and Softlock Enabled
PROGRAM/ERASE STATUS: The device provides several bits to determine the status
of a program or erase operation: I/O2, I/O3, I/O5, I/O6, and I/O7. All other status bits are
don’t care. Table 3 on page 11 and the following four sections describe the function of
these bits. To provide greater flexibility for system designers, the 64-Mbit device contains a programmable configuration register. The configuration register allows the user
to specify the status bit operation. The configuration register can be set to one of two different values, “00” or “01”. If the configuration register is set to “00”, the part will
automatically return to the read mode after a successful program or erase operation. If
the configuration register is set to a “01”, a Product ID Exit command must be given after
a successful program or erase operation before the part will return to the read mode. It
is important to note that whether the configuration register is set to a “00” or to a “01”,
any unsuccessful program or erase operation requires using the Product ID Exit command to return the device to read mode. The default value (after power-up) for the
configuration register is “00”. Using the four-bus cycle set configuration register command as shown in the Command Definition table on page 12, the value of the
configuration register can be changed. Voltages applied to the reset pin will not alter the
value of the configuration register. The value of the configuration register will affect the
operation of the I/O7 status bit as described below.
DATA POLLING: The 64-Mbit device features Data Polling to indicate the end of a program cycle. If the status configuration register is set to a “00”, during a program cycle an
attempted read of the last word loaded will result in the complement of the loaded data
on I/O7. Once the program cycle has been completed, true data is valid on all outputs
and the next cycle may begin. During a chip or sector erase operation, an attempt to
read the device will give a “0” on I/O7. Once the program or erase cycle has completed,
true data will be read from the device. Data Polling may begin at any time during the program cycle. Please see Table 3 on page 11 for more details.
If the status bit configuration register is set to a “01”, the I/O7 status bit will be low while
the device is actively programming or erasing data. I/O7 will go high when the device
has completed a program or erase operation. Once I/O7 has gone high, status information on the other pins can be checked.
The Data Polling status bit must be used in conjunction with the erase/program and VPP
status bit as shown in the algorithm in Figures 2 and 3.
TOGGLE BIT: In addition to Data Polling, the 64-Mbit device provides another method
for determining the end of a program or erase cycle. During a program or erase operation, successive attempts to read data from the memory will result in I/O6 toggling
between one and zero. Once the program cycle has completed, I/O6 will stop toggling
6
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. Please see Table 3 on page 11 for more details.
The toggle bit status bit should be used in conjunction with the erase/program and VPP
status bit as shown in the algorithm in Figures 4 and 5 on page 10.
ERASE/PROGRAM STATUS BIT: The device offers a status bit on I/O5 that indicates
whether the program or erase operation has exceeded a specified internal pulse count
limit. If the status bit is a “1”, the device is unable to verify that an erase or a word program operation has been successfully performed. The device may also output a “1” on
I/O5 if the system tries to program a “1” to a location that was previously programmed to
a “0”. Only an erase operation can change a “0” back to a “1”. If a program (Sector
Erase) command is issued to a protected sector, the protected sector will not be programmed (erased). The device will go to a status read mode and the I/O5 status bit will
be set high, indicating the program (erase) operation did not complete as requested.
Once the erase/program status bit has been set to a “1”, the system must write the
Product ID Exit command to return to the read mode. The erase/program status bit is a
“0” while the erase or program operation is still in progress. Please see Table 3 on page
11 for more details.
VPP STATUS BIT: The 64-Mbit device provides a status bit on I/O3 that provides information regarding the voltage level of the VPP pin. During a program or erase operation,
if the voltage on the VPP pin is not high enough to perform the desired operation successfully, the I/O3 status bit will be a “1”. Once the VPP status bit has been set to a “1”,
the system must write the Product ID Exit command to return to the read mode. On the
other hand, if the voltage level is high enough to perform a program or erase operation
successfully, the VPP status bit will output a “0”. Please see Table 3 on page 11 for more
details.
ERASE SUSPEND/ERASE RESUME: The Erase Suspend command allows the system to interrupt a sector erase operation and then program or read data from a different
sector within the same plane. Since this device has a multiple plane architecture, there
is no need to use the erase suspend feature while erasing a sector when you want to
read data from a sector in another plane. After the Erase Suspend command is given,
the device requires a maximum time of 15 µs to suspend the erase operation. After the
erase operation has been suspended, the plane that contains the suspended sector
enters the erase-suspend-read mode. The system can then read data or program data
to any other sector within the device. An address is not required during the Erase Suspend command. During a sector erase suspend, another sector cannot be erased. To
resume the sector erase operation, the system must write the Erase Resume command.
The Erase Resume command is a one-bus cycle command, which does require the
plane address. The device also supports an erase suspend during a complete chip
erase. While the chip erase is suspended, the user can read from any sector within the
memory that is protected. The command sequence for a chip erase suspend and a sector erase suspend are the same.
PROGRAM SUSPEND/PROGRAM RESUME: The Program Suspend command allows
the system to interrupt a programming operation and then read data from a different
word within the memory. After the Program Suspend command is given, the device
requires a maximum of 10 µs to suspend the programming operation. After the programming operation has been suspended, the system can then read from any other word
within the device. An address is not required during the program suspend operation. To
resume the programming operation, the system must write the Program Resume command. The program suspend and resume are one-bus cycle commands. The command
sequence for the erase suspend and program suspend are the same, and the command
sequence for the erase resume and program resume are the same.
7
3441B–STKD–11/04
128-BIT PROTECTION REGISTER: The 64-Mbit device contains a 128-bit register that
can be used for security purposes in system design. The protection register is divided
into two 64-bit blocks. The two blocks are designated as block A and block B. The data
in block A is non-changeable and is programmed at the factory with a unique number.
The data in block B is programmed by the user and can be locked out such that data in
the block cannot be reprogrammed. To program block B in the protection register, the
four-bus cycle Program Protection Register command must be used as shown in the
Command Definition table on page 12. To lock out block B, the four-bus cycle lock protection register command must be used as shown in the Command Definition table.
Data bit D1 must be zero during the fourth bus cycle. All other data bits during the fourth
bus cycle are don’t cares. To determine whether block B is locked out, the status of
Block B Protection command is given. If data bit D1 is zero, block B is locked. If data bit
D1 is one, block B can be reprogrammed. Please see the Protection Register Addressing Table on page 13 for the address locations in the protection register. To read the
protection register, the Product ID Entry command is given followed by a normal read
operation from an address within the protection register. After determining whether
block B is protected or not or reading the protection register, the Product ID Exit command must be given prior to performing any other operation.
CFI: Common Flash Interface (CFI) is a published, standardized data structure that
may be read from a Flash device. CFI allows system software to query the installed
device to determine the configurations, various electrical and timing parameters, and
functions supported by the device. CFI is used to allow the system to learn how to interface to the Flash device most optimally. The two primary benefits of using CFI are ease
of upgrading and second source availability. The command to enter the CFI Query
mode is a one-bus cycle command which requires writing data 98h to address 55h. The
CFI Query command can be written when the device is ready to read data or can also
be written when the part is in the product ID mode. Once in the CFI Query mode, the
system can read CFI data at the addresses given in Table 4 on page 24. To exit the CFI
Query mode, the product ID exit command must be given. If the CFI Query command is
given while the part is in the product ID mode, then the product ID exit command must
first be given to return the part to the product ID mode. Once in the product ID mode, it
will be necessary to give another product ID exit command to return the part to the read
mode.
HARDWARE DATA PROTECTION: Hardware features protect against inadvertent programs to the 64-Mbit device in the following ways: (a) VCC sense: if VCC is below 1.8V
(typical), the program function is inhibited. (b) V CC power-on delay: once VCC has
reached the V CC sense level, the device will automatically time-out 10 ms (typical)
before programming. (c) Program inhibit: holding any one of OE low, CE high or WE
high inhibits program cycles. (d) Noise filter: pulses of less than 15 ns (typical) on the
WE or CE inputs will not initiate a program cycle. (e) VPP is less than VILPP.
INPUT LEVELS: While operating with a 2.7V to 3.1V power supply, the address inputs
and control inputs (OE, CE and WE) may be driven from 0 to 5.5V without adversely
affecting the operation of the device. The I/O lines can be driven from 0 to VCCQ + 0.6V.
8
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Figure 2. Data Polling Algorithm
(Configuration Register = 00)
Figure 3. Data Polling Algorithm
(Configuration Register = 01)
START
START
Read I/O7 - I/O0
Addr = VA
Read I/O7 - I/O0
Addr = VA
NO
YES
I/O7 = 1?
I/O7 = Data?
YES
NO
NO
I/O3, I/O5 = 1?
I/O3, I/O5 = 1?
YES
YES
Read I/O7 - I/O0
Addr = VA
I/O7 = Data?
Notes:
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
YES
NO
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
NO
Note:
Program/Erase
Operation
Successful,
Device in
Read Mode
Program/Erase
Operation
Successful,
Write Product ID
Exit Command
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector address
within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector
address within the sector being erased. During
chip erase, a valid address is any non-protected
sector address.
2. I/O7 should be rechecked even if I/O5 = “1”
because I/O7 may change simultaneously with
I/O5.
9
3441B–STKD–11/04
Figure 5. Toggle Bit Algorithm
(Configuration Register = 01)
Figure 4. Toggle Bit Algorithm
(Configuration Register = 00)
START
START
Read I/O7 - I/O0
Read I/O7 - I/O0
Read I/O7 - I/O0
Read I/O7 - I/O0
Toggle Bit =
Toggle?
Toggle Bit =
Toggle?
NO
YES
YES
NO
NO
I/O3, I/O5 = 1?
Read I/O7 - I/O0
Twice
Read I/O7 - I/O0
Twice
Toggle Bit =
Toggle?
NO
Note:
10
NO
YES
YES
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
I/O3, I/O5 = 1?
YES
YES
Toggle Bit =
Toggle?
NO
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
Program/Erase
Operation
Successful,
Device in
Read Mode
1. The system should recheck the toggle bit even if
I/O5 = “1” because the toggle bit may stop toggling
as I/O5 changes to “1”.
Note:
Program/Erase
Operation
Successful,
Write Product ID
Exit Command
1. The system should recheck the toggle bit even if I/O5 =
“1” because the toggle bit may stop toggling as I/O5
changes to “1”.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Table 3. Status Bit Table
I/O7
Configuration
Register:
I/O6
I/O2
00/01
00/01
00/01
00/01
00/01
00/01
00/01
00/01
00/01
00/01
00/01
00/01
Plane A
Plane B
Plane C
Plane D
Plane A
Plane B
Plane C
Plane D
Plane A
Plane B
Plane C
Plane D
Programming
in Plane A
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
1
DATA
DATA
DATA
Programming
in Plane B
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
1
DATA
DATA
Programming
in Plane C
DATA
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
1
DATA
Programming
in Plane D
DATA
DATA
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
1
Erasing in
Plane A
0/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
Erasing in
Plane B
DATA
0/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
DATA
Erasing in
Plane C
DATA
DATA
0/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
Erasing in
Plane D
DATA
DATA
DATA
0/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
Erase
Suspended &
Read Erasing
Sector
1
1
1
1
1
1
1
1
TOGGLE
TOGGLE
TOGGLE
TOGGLE
Erase
Suspended &
Read Nonerasing Sector
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
Erase
Suspended &
Program Nonerasing Sector
in Plane A
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
Erase
Suspended &
Program Nonerasing Sector
in Plane B
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
DATA
Erase
Suspended &
Program Nonerasing Sector
in Plane C
DATA
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
DATA
Erase
Suspended &
Program Nonerasing Sector
in Plane D
DATA
DATA
DATA
I/O7/0
DATA
DATA
DATA
TOGGLE
DATA
DATA
DATA
TOGGLE
Read Address
In
While
11
3441B–STKD–11/04
Command Definition (Hex)(1)
1st Bus
Cycle
Bus
Cycles
Addr
Data
Read
1
Addr
DOUT
Chip Erase
6
555
AA
Command Sequence
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
5th Bus
Cycle
6th Bus
Cycle
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
AAA(2)
55
555
80
555
AA
AAA
55
555
10
(6)
20
Plane Erase
6
555
AA
AAA
55
555
80
555
AA
AAA
55
PA
Sector Erase
6
555
AA
AAA
55
555
80
555
AA
AAA
55
SA(4)
30
Word Program
4
555
AA
AAA
55
555
A0
Addr
DIN
Dual-Word Program(8)
5
555
AA
AAA
55
555
A1
Addr0
DIN0
Addr1
DIN1
Enter Single-pulse Program
Mode
6
555
AA
AAA
55
555
80
555
AA
AAA
55
555
A0
Single-pulse Word Program
Mode
1
Addr
DIN
Sector Softlock
6
555
AA
AAA
55
555
80
555
AA
AAA
55
SA(4)
40
Sector Unlock
2
555
AA
SA(4)
70
Sector Hardlock
6
555
AA
AAA
55
555
80
555
AA
AAA
55
SA(4)(5)
60
Erase/Program Suspend
1
xxx
B0
Erase/Program Resume
1
PA(6)
30
Product ID Entry(7)
3
555
AA
AAA
55
PA+00555
90
(3)
Product ID Exit
3
555
AA
AAA
55
555
F0
Product ID Exit(3)
1
xxx
FX
Program Protection
Register – Block B
4
555
AA
AAA
55
555
C0
xxxx(12)8x(11)
DIN
Lock Protection
Register – Block B
4
555
AA
AAA
55
555
C0
xxxx80(12)
X0
Status of Block B
Protection
4
555
AA
AAA
55
555
90
xxxx80(13)
DOUT(9)
Set Configuration Register
4
555
AA
AAA
55
555
E0
xxx
00/01(10)
CFI Query
1
X55
98
Notes:
12
1. The DATA FORMAT in each bus cycle is as follows: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex). The ADDRESS FORMAT in each bus cycle
is as follows: A11 - A0 (Hex), A11 - A21 (Don’t Care).
2. Since A11 is a Don’t Care, AAA can be replaced with 2AA.
3. Either one of the Product ID Exit commands can be used.
4. SA = sector address. Any word address within a sector can be used to designate the sector address (see pages 14 - 17 for details).
5. Once a sector is in the Hardlock protection mode, it cannot be disabled unless the chip is reset or power cycled.
6. PA is the plane address (A21 - A20).
7. During the fourth bus cycle, the manufacturer code is read from address PA+00000H, the device code is read from address PA+00001H,
and the data in the protection register is read from addresses 000081H - 000088H. PA (A21 - A20) must specify the same plane address as
specified in the third bus cycle.
8. The fast programming option enables the user to program two words in parallel only when VPP = 12V. The addresses, Addr0 and Addr1, of
the two words, DIN0 and DIN1, must only differ in address A0. This command should be used for manufacturing purpose only.
9. If data bit D1 is “0”, block B is locked. If data bit D1 is “1”, block B can be reprogrammed.
10. The default state (after power-up) of the configuration register is “00”.
11. Any address within the user programmable register region. Please see “Protection Register Addressing Table” on page 13.
12. For the AT49BV6416, xxxx = 0000H. For the AT49BV6416T, xxxx = 3F80H.
13. For the AT49BV6416, xxxx = 0000H. For the AT49BV6416T, xxxx = 0F80H.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Absolute Maximum Ratings*
*NOTICE:
Temperature under Bias ................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages Except VPP
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
VPP Input Voltage
with Respect to Ground ......................................... 0V to 13.0V
All Output Voltages
with Respect to Ground ...........................-0.6V to VCCQ + 0.6V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Protection Register Addressing Table
Word
Use
Block
A7
A6
A5
A4
A3
A2
A1
A0
0
Factory
A
1
0
0
0
0
0
0
1
1
Factory
A
1
0
0
0
0
0
1
0
2
Factory
A
1
0
0
0
0
0
1
1
3
Factory
A
1
0
0
0
0
1
0
0
4
User
B
1
0
0
0
0
1
0
1
5
User
B
1
0
0
0
0
1
1
0
6
User
B
1
0
0
0
0
1
1
1
7
User
B
1
0
0
0
1
0
0
0
13
3441B–STKD–11/04
Memory Organization – 64-Mbit Bottom Boot
Memory Organization – 64-Mbit Bottom Boot (Continued)
x16
x16
Plane
A
SA0
Size
(Words)
Address Range
(A21 - A0)
4K
00000 - 00FFF
A
SA1
4K
01000 - 01FFF
A
SA2
4K
02000 - 02FFF
A
SA3
4K
03000 - 03FFF
A
SA4
4K
04000 - 04FFF
A
SA5
4K
05000 - 05FFF
A
SA6
4K
06000 - 06FFF
A
SA7
4K
07000 - 07FFF
A
SA8
32K
08000 - 0FFFF
A
SA9
32K
10000 - 17FFF
A
SA10
32K
18000 - 1FFFF
A
SA11
32K
20000 - 27FFF
A
SA12
32K
28000 - 2FFFF
A
SA13
32K
30000 - 37FFF
A
SA14
32K
38000 - 3FFFF
A
SA15
32K
40000 - 47FFF
A
SA16
32K
48000 - 4FFFF
A
SA17
32K
50000 - 57FFF
A
SA18
32K
58000 - 5FFFF
A
SA19
32K
60000 - 67FFF
A
SA20
32K
68000 - 6FFFF
A
SA21
32K
70000 - 77FFF
A
SA22
32K
78000 - 7FFFF
A
SA23
32K
80000 - 87FFF
A
SA24
32K
88000 - 8FFFF
A
SA25
32K
90000 - 97FFF
A
SA26
32K
98000 - 9FFFF
A
SA27
32K
A0000 - A7FFF
A
SA28
32K
A8000 - AFFFF
A
SA29
32K
B0000 - B7FFF
A
SA30
32K
B8000 - BFFFF
A
SA31
32K
C0000 - C7FFF
A
SA32
32K
C8000 - CFFFF
A
SA33
32K
D0000 - D7FFF
A
SA34
32K
D8000 - DFFFF
A
SA35
32K
E0000 - E7FFF
A
SA36
32K
E8000 - EFFFF
A
SA37
32K
F0000 - F7FFF
A
SA38
32K
F8000 - FFFFF
B
SA39
32K
100000 - 107FFF
B
SA40
32K
108000 - 10FFFF
B
SA41
32K
110000 - 117FFF
B
SA42
32K
118000 - 11FFFF
B
SA43
32K
120000 - 127FFF
B
14
Sector
SA44
32K
128000 - 12FFFF
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
B
SA45
32K
130000 - 137FFF
B
SA46
32K
138000 - 13FFFF
B
SA47
32K
140000 - 147FFF
B
SA48
32K
148000 - 14FFFF
B
SA49
32K
150000 - 157FFF
B
SA50
32K
158000 - 15FFFF
B
SA51
32K
160000 - 167FFF
B
SA52
32K
168000 - 16FFFF
B
SA53
32K
170000 - 177FFF
B
SA54
32K
178000 - 17FFFF
B
SA55
32K
180000 - 187FFF
B
SA56
32K
188000 - 18FFFF
B
SA57
32K
190000 - 197FFF
B
SA58
32K
198000 - 19FFFF
B
SA59
32K
1A0000 - 1A7FFF
B
SA60
32K
1A8000 - 1AFFFF
B
SA61
32K
1B0000 - 1B7FFF
B
SA62
32K
1B8000 - 1BFFFF
B
SA63
32K
1C0000 - 1C7FFF
1C8000 - 1CFFFF
B
SA64
32K
B
SA65
32K
1D0000 - 1D7FFF
B
SA66
32K
1D8000 - 1DFFFF
B
SA67
32K
1E0000 - 1E7FFF
1E8000 - 1EFFFF
B
SA68
32K
B
SA69
32K
1F0000 - 1F7FFF
B
SA70
32K
1F8000 - 1FFFFF
C
SA71
32K
200000 - 207FFF
C
SA72
32K
208000 - 20FFFF
C
SA73
32K
210000 - 217FFF
218000 - 21FFFF
C
SA74
32K
C
SA75
32K
220000 - 227FFF
C
SA76
32K
228000 - 22FFFF
C
SA77
32K
230000 - 237FFF
238000 - 23FFFF
C
SA78
32K
C
SA79
32K
240000 - 247FFF
C
SA80
32K
248000 - 24FFFF
C
SA81
32K
250000 - 257FFF
C
SA82
32K
258000 - 25FFFF
C
SA83
32K
260000 - 267FFF
268000 - 26FFFF
C
SA84
32K
C
SA85
32K
270000 - 277FFF
C
SA86
32K
278000 - 27FFFF
C
SA87
32K
280000 - 287FFF
C
SA88
32K
288000 - 28FFFF
C
SA89
32K
290000 - 297FFF
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Memory Organization – 64-Mbit Bottom Boot (Continued)
Memory Organization – 64-Mbit Bottom Boot (Continued)
x16
x16
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
C
SA90
32K
298000 - 29FFFF
D
SA113
32K
350000 - 357FFF
C
SA91
32K
2A0000 - 2A7FFF
D
SA114
32K
358000 - 35FFFF
C
SA92
32K
2A8000 - 2AFFFF
D
SA115
32K
360000 - 367FFF
C
SA93
32K
2B0000 - 2B7FFF
D
SA116
32K
368000 - 36FFFF
C
SA94
32K
2B8000 - 2BFFFF
D
SA117
32K
370000 - 377FFF
C
SA95
32K
2C0000 - 2C7FFF
D
SA118
32K
378000 - 37FFFF
C
SA96
32K
2C8000 - 2CFFFF
D
SA119
32K
380000 - 387FFF
C
SA97
32K
2D0000 - 2D7FFF
D
SA120
32K
388000 - 38FFFF
C
SA98
32K
2D8000 - 2DFFFF
D
SA121
32K
390000 - 397FFF
C
SA99
32K
2E0000 - 2E7FFF
D
SA122
32K
398000 - 39FFFF
C
SA100
32K
2E8000 - 2EFFFF
D
SA123
32K
3A0000 - 3A7FFF
C
SA101
32K
2F0000 - 2F7FFF
D
SA124
32K
3A8000 - 3AFFFF
D
SA102
32K
2F8000 - 2FFFFF
D
SA125
32K
3B0000 - 3B7FFF
D
SA103
32K
300000 - 307FFF
D
SA126
32K
3B8000 - 3BFFFF
D
SA104
32K
308000 - 30FFFF
D
SA127
32K
3C0000 - 3C7FFF
D
SA105
32K
310000 - 317FFF
D
SA128
32K
3C8000 - 3CFFFF
318000 - 31FFFF
D
SA129
32K
3D0000 - 3D7FFF
3D8000 - 3DFFFF
D
SA106
32K
D
SA107
32K
320000 - 327FFF
D
SA130
32K
D
SA108
32K
328000 - 32FFFF
D
SA131
32K
3E0000 - 3E7FFF
D
SA109
32K
330000 - 337FFF
D
SA132
32K
3E8000 - 3EFFFF
D
SA110
32K
338000 - 33FFFF
D
SA133
32K
3F0000 - 3F7FFF
D
SA111
32K
340000 - 347FFF
D
SA134
32K
3F8000 - 3FFFFF
D
SA112
32K
348000 - 34FFFF
15
3441B–STKD–11/04
Memory Organization – 64-Mbit Top Boot
Memory Organization – 64-Mbit Top Boot (Continued)
x16
x16
Plane
16
Sector
Size
(Words)
Address Range
(A21 - A0)
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
168000 - 16FFFF
D
SA0
32K
00000 - 07FFF
C
SA45
32K
D
SA1
32K
08000 - 0FFFF
C
SA46
32K
170000 - 177FFF
SA47
32K
178000 - 17FFFF
D
SA2
32K
10000 - 17FFF
C
D
SA3
32K
18000 - 1FFFF
C
SA48
32K
180000 - 187FFF
D
SA4
32K
20000 - 27FFF
C
SA49
32K
188000 - 18FFFF
D
SA5
32K
28000 - 2FFFF
C
SA50
32K
190000 - 197FFF
SA51
32K
198000 - 19FFFF
D
SA6
32K
30000 - 37FFF
C
D
SA7
32K
38000 - 3FFFF
C
SA52
32K
1A0000 - 1A7FFF
D
SA8
32K
40000 - 47FFF
C
SA53
32K
1A8000 - 1AFFFF
D
SA9
32K
48000 - 4FFFF
C
SA54
32K
1B0000 - 1B7FFF
D
SA10
32K
50000 - 57FFF
C
SA55
32K
1B8000 - 1BFFFF
D
SA11
32K
58000 - 5FFFF
C
SA56
32K
1C0000 - 1C7FFF
D
SA12
32K
60000 - 67FFF
C
SA57
32K
1C8000 - 1CFFFF
68000 - 6FFFF
C
SA58
32K
1D0000 - 1D7FFF
1D8000 - 1DFFFF
D
SA13
32K
D
SA14
32K
70000 - 77FFF
C
SA59
32K
D
SA15
32K
78000 - 7FFFF
C
SA60
32K
1E0000 - 1E7FFF
SA61
32K
1E8000 - 1EFFFF
D
SA16
32K
80000 - 87FFF
C
D
SA17
32K
88000 - 8FFFF
C
SA62
32K
1F0000 - 1F7FFF
D
SA18
32K
90000 - 97FFF
C
SA63
32K
1F8000 - 1FFFFF
D
SA19
32K
98000 - 9FFFF
B
SA64
32K
200000 - 207FFF
D
SA20
32K
A0000 - A7FFF
B
SA65
32K
208000 - 20FFFF
D
SA21
32K
A8000 - AFFFF
B
SA66
32K
210000 - 217FFF
SA67
32K
218000 - 21FFFF
D
SA22
32K
B0000 - B7FFF
B
D
SA23
32K
B8000 - BFFFF
B
SA68
32K
220000 - 227FFF
D
SA24
32K
C0000 - C7FFF
B
SA69
32K
228000 - 22FFFF
D
SA25
32K
C8000 - CFFFF
B
SA70
32K
230000 - 237FFF
SA71
32K
238000 - 23FFFF
D
SA26
32K
D0000 - D7FFF
B
D
SA27
32K
D8000 - DFFFF
B
SA72
32K
240000 - 247FFF
D
SA28
32K
E0000 - E7FFF
B
SA73
32K
248000 - 24FFFF
D
SA29
32K
E8000 - EFFFF
B
SA74
32K
250000 - 257FFF
D
SA30
32K
F0000 - F7FFF
B
SA75
32K
258000 - 25FFFF
D
SA31
32K
F8000 - FFFFF
B
SA76
32K
260000 - 267FFF
SA77
32K
268000 - 26FFFF
C
SA32
32K
100000 - 107FFF
B
C
SA33
32K
108000 - 10FFFF
B
SA78
32K
270000 - 277FFF
C
SA34
32K
110000 - 117FFF
B
SA79
32K
278000 - 27FFFF
C
SA35
32K
118000 - 11FFFF
B
SA80
32K
280000 - 287FFF
SA81
32K
288000 - 28FFFF
290000 - 297FFF
C
SA36
32K
120000 - 127FFF
B
C
SA37
32K
128000 - 12FFFF
B
SA82
32K
C
SA38
32K
130000 - 137FFF
B
SA83
32K
298000 -29FFFF
SA84
32K
2A0000 - 2A7FFF
2A8000 - 2AFFFF
C
SA39
32K
138000 - 13FFFF
B
C
SA40
32K
140000 - 147FFF
B
SA85
32K
C
SA41
32K
148000 - 14FFFF
B
SA86
32K
2B0000 - 2B7FFF
SA87
32K
2B8000 - 2BFFFF
C
SA42
32K
150000 - 157FFF
B
C
SA43
32K
158000 - 15FFFF
B
SA88
32K
2C0000 - 2C7FFF
C
SA44
32K
160000 - 167FFF
B
SA89
32K
2C8000 - 2CFFFF
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Memory Organization – 64-Mbit Top Boot (Continued)
Memory Organization – 64-Mbit Top Boot (Continued)
x16
x16
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
Plane
Sector
Size
(Words)
Address Range
(A21 - A0)
388000 - 38FFFF
B
SA90
32K
2D0000 - 2D7FFF
A
SA113
32K
B
SA91
32K
2D8000 - 2DFFFF
A
SA114
32K
390000 - 397FFF
B
SA92
32K
2E0000 - 2E7FFF
A
SA115
32K
398000 - 39FFFF
B
SA93
32K
2E8000 - 2EFFFF
A
SA116
32K
3A0000 - 3A7FFF
B
SA94
32K
2F0000 - 2F7FFF
A
SA117
32K
3A8000 - 3AFFFF
B
SA95
32K
2F8000 - 2FFFFF
A
SA118
32K
3B0000 - 3B7FFF
SA119
32K
3B8000 - 3BFFFF
A
SA96
32K
300000 - 307FFF
A
A
SA97
32K
308000 - 30FFFF
A
SA120
32K
3C0000 - 3C7FFF
A
SA98
32K
310000 - 317FFF
A
SA121
32K
3C8000 - 3CFFFF
A
SA99
32K
318000 - 31FFFF
A
SA122
32K
3D0000 - 3D7FFF
A
SA100
32K
320000 - 327FFF
A
SA123
32K
3D8000 - 3DFFFF
A
SA101
32K
328000 - 32FFFF
A
SA124
32K
3E0000 - 3E7FFF
A
SA102
32K
330000 - 337FFF
A
SA125
32K
3E8000 - 3EFFFF
A
SA103
32K
338000 - 33FFFF
A
SA126
32K
3F0000 - 3F7FFF
A
SA104
32K
340000 - 347FFF
A
SA127
4K
3F8000 - 3F8FFF
A
SA105
32K
348000 - 34FFFF
A
SA128
4K
3F9000 - 3F9FFF
SA129
4K
3FA000 - 3FAFFF
A
SA106
32K
350000 - 357FFF
A
A
SA107
32K
358000 - 35FFFF
A
SA130
4K
3FB000 - 3FBFFF
A
SA108
32K
360000 - 367FFF
A
SA131
4K
3FC000 - 3FCFFF
A
SA109
32K
368000 - 36FFFF
A
SA132
4K
3FD000 - 3FDFFF
A
SA110
32K
370000 - 377FFF
A
SA133
4K
3FE000 - 3FEFFF
A
SA111
32K
378000 - 37FFFF
A
SA134
4K
3FF000 - 3FFFFF
A
SA112
32K
380000 - 387FFF
17
3441B–STKD–11/04
DC and AC Operating Range
64-Mbit Device – 70, 85 ns
Operating Temperature (Case)
Industrial
-40°C - 85°C
VCC Power Supply
2.7V - 3.6V
Operating Modes
Mode
CE
Read
VIL
VIL
Burst Read
(3)
Program/Erase
Standby/Program Inhibit
VIL
WE
RESET
VPP(4)
Ai
I/O
VIL
VIH
VIH
X
Ai
DOUT
VIL
VIH
VIH
X
Ai
DOUT
VIL
VIH
VIHPP(5)
Ai
DIN
X
High Z
OE
VIH
(1)
VIH
X
X
VIH
X
X
X
VIH
VIH
X
X
VIL
X
VIH
X
X
X
X
X
VILPP(6)
Output Disable
X
VIH
X
VIH
X
Reset
X
X
X
VIL
X
Program Inhibit
High Z
X
High Z
A0 = VIL, A1 - A21 = VIL
Manufacturer Code(3)
A0 = VIH, A1 - A21 = VIL
Device Code(3)
Product Identification
Software
Notes:
1. X can be VIL or VIH.
2.
3.
4.
5.
6.
18
VIH
Refer to AC programming waveforms.
Manufacturer Code: 001FH; Device Code: 00D6H – Bottom Boot; 00D2H – Top Boot.
The VPP pin can be tied to VCC. For faster program/erase operations, VPP can be set to 12.0V ± 0.5V.
VIHPP (min) = 1.65V.
VILPP (max) = 0.8V.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
DC Characteristics
Symbol
Parameter
Condition
ILI
Input Load Current
ILO
Max
Units
VIN = 0V to VCC
1
µA
Output Leakage Current
VI/O = 0V to VCC
1
µA
ISB1
VCC Standby Current CMOS
CE = VCCQ - 0.3V to VCC
35
µA
ICC(1)
VCC Active Current
f = 66 MHz; IOUT = 0 mA
30
mA
ICCRE
VCC Read While Erase Current
f = 66 MHz; IOUT = 0 mA
50
mA
ICCRW
VCC Read While Write Current
f = 66 MHz; IOUT = 0 mA
50
mA
VIL
Input Low Voltage
0.6
V
VIH
Input High Voltage
VOL
Output Low Voltage
VOH
Output High Voltage
Note:
Min
2.0
IOL = 2.1 mA
V
0.45
IOH = -100 µA
2.5
IOH = -400 µA
2.4
V
V
1. In the erase mode, ICC is 35 mA.
Input Test Waveforms and Measurement Level
2.0V
AC
DRIVING
LEVELS
1.5V
AC
MEASUREMENT
LEVEL
0.6V
tR, tF < 5 ns
Output Test Load
V CC
1.8K
OUTPUT
PIN
1.3K
30 pF
Pin Capacitance
f = 1 MHz, T = 25°C(1)
Typ
Max
Units
Conditions
CIN
4
6
pF
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
1. This parameter is characterized and is not 100% tested.
19
3441B–STKD–11/04
AC Asynchronous Read Timing Characteristics
64-Mbit-70
Symbol
Parameter
Min
tACC
Access, Address to Data Valid
tCE
Access, CE to Data Valid
64-Mbit-85
Max
Min
Max
Units
70
85
ns
70
85
ns
tOE
OE to Data Valid
20
20
ns
tDF
CE, OE High to Data Float
25
25
ns
tRO
RESET to Output Delay
150
150
ns
Asynchronous Read Cycle Waveform(1)(2)(3)
tRC
A0 - A21
ADDRESS VALID
CE
tCE
tOE
OE
tDF
tOH
tACC
tRO
RESET
I/O0 - I/O15
Notes:
20
HIGH Z
OUTPUT
VALID
1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change
without impact on tACC.
3. tDF is specified from OE or CE, whichever occurs first (CL = 5 pF).
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
AC Word Load Characteristics
Symbol
Parameter
Min
Max
Units
tAS
Address Setup Time to WE and CE Low
0
ns
tAH
Address Hold Time
20
ns
tDS
Data Setup Time
20
ns
tDH
Data Hold Time
0
ns
tWP
CE or WE Low Pulse Width
35
ns
tWPH
CE or WE High Pulse Width
25
ns
AC Word Load Waveforms
WE Controlled
CE
I/O0-I/O15
DATA VALID
A0 -A21
tDS
tDH
tAH
tAS
tWP
WE
CE Controlled
WE
I/O0-I/O15
DATA VALID
A0 -A21
tDS
tAS
CE
tDH
tAH
tWP
21
3441B–STKD–11/04
Program Cycle Characteristics
Symbol
Parameter
Min
Typ
Max
Units
tBP
Word Programming Time (Vpp = VCC)
22
µs
tBPVPP
Word Programming Time (VPP > 11.5V)
10
µs
tSEC1
Sector Erase Cycle Time (4K word sectors)
100
ms
tSEC2
Sector Erase Cycle Time (32K word sectors)
500
ms
tES
Erase Suspend Time
15
µs
tPS
Program Suspend Time
10
µs
Program Cycle Waveforms
OE(1)
CE
XXAA
I/O0 -I/O15
XX55
555
A0 -A21
AAA
INPUT
DATA
XXA0
555
ADDR
WE
Sector, Plane or Chip Erase Cycle Waveforms
OE(1)
CE
XXAA
I/O0 -I/O15
A0 -A21
555
XX55
AAA
555
555
Note3
XX55
XXAA
XX80
AAA
Note2
WE
Notes:
22
1. OE must be high only when WE and CE are both low.
2. For chip erase, the address should be 555. For plane or sector erase, the address depends on what plane or sector is to be
erased. (See note 4 and 6 under Command Definitions on page 12.)
3. For chip erase, the data should be XX10H, for plane erase, the data should be XX20H, and for sector erase, the data should
be XX30H
4. The waveforms shown above use the WE controlled AC Word Load Waveforms.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Data Polling Characteristics
Symbol
Parameter
Min
tDH
Data Hold Time
10
ns
tOEH
OE Hold Time
10
ns
tOE
OE to Output Delay(2)
tWR
Notes:
Typ
Max
Units
ns
Write Recovery Time
0
ns
1. These parameters are characterized and not 100% tested.
2. See tOE spec on page 20.
Data Polling Waveforms
WE
CE
OE
I/O7
A0-A21
Toggle Bit Characteristics(1)
Symbol
Parameter
tDH
Data Hold Time
10
ns
tOEH
OE Hold Time
10
ns
tOE
OE to Output Delay(2)
tOEHP
OE High Pulse
50
ns
Write Recovery Time
0
ns
tWR
Notes:
Min
Typ
Max
Units
ns
1. These parameters are characterized and not 100% tested.
2. See tOE spec on page 20.
Toggle Bit Waveforms(1)(2)(3)
Notes:
1. Toggling either OE or CE or both OE and CE will operate toggle bit.
The tOEHP specification must be met by the toggling input(s).
2. Beginning and ending state of I/O6 will vary.
3. Any address location may be used but the address should not vary.
23
3441B–STKD–11/04
Table 4. Common Flash Interface Definition for 64-Mbit Device
24
Address
64-Mbit Device
Comments
10h
0051h
“Q”
11h
0052h
“R”
12h
0059h
“Y”
13h
0002h
14h
0000h
15h
0041h
16h
0000h
17h
0000h
18h
0000h
19h
0000h
1Ah
0000h
1Bh
0027h
VCC min write/erase
1Ch
0031h
VCC max write/erase
1Dh
00B5h
VPP min voltage
1Eh
00C5h
VPP max voltage
1Fh
0004h
Typ word write – 16 µs
20h
0000h
21h
0009h
Typ block erase – 500 ms
22h
0010h
Typ chip erase, 64,300 ms
23h
0004h
Max word write/typ time
24h
0000h
n/a
25h
0003h
Max block erase/typ block erase
26h
0003h
Max chip erase/ typ chip erase
27h
0017h
Device size
28h
0001h
x16 device
29h
0000h
x16 device
2Ah
0000h
Multiple byte write not supported
2Bh
0000h
Multiple byte write not supported
2Ch
0002h
2 regions, x = 2
2Dh
007Eh
64K bytes, Y = 126
2Eh
0000h
64K bytes, Y = 126
2Fh
0000h
64K bytes, Z = 256
30h
0001h
64K bytes, Z = 256
31h
0007h
8K bytes, Y = 7
32h
0000h
8K bytes, Y = 7
33h
0020h
8K bytes, Z = 32
34h
0000h
8K bytes, Z = 32
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Table 4. Common Flash Interface Definition for 64-Mbit Device (Continued)
Address
64-Mbit Device
Comments
VENDOR SPECIFIC EXTENDED QUERY
41h
0050h
“P”
42h
0052h
“R”
43h
0049h
“I”
44h
0031h
Major version number, ASCII
45h
0030h
Minor version number, ASCII
46h
008Fh
Bit 0 – chip erase supported, 0 – no, 1 – yes
Bit 1 – erase suspend supported, 0 – no, 1 – yes
Bit 2 – program suspend supported, 0 – no, 1 – yes
Bit 3 – simultaneous operations supported, 0 – no, 1 – yes
Bit 4 – burst mode read supported, 0 – no, 1 – yes
Bit 5 – page mode read supported, 0 – no, 1 – yes
Bit 6 – queued erase supported, 0 – no, 1 – yes
Bit 7 – protection bits supported, 0 – no, 1 – yes
47h
0000h Top Boot or
0001h Bottom Boot
48h
0000h
Bit 0 – 4 word linear burst with wrap around, 0 – no, 1 – yes
Bit 1 – 8 word linear burst with wrap around, 0 – no, 1 – yes
Bit 2 – continuos burst, 0 – no, 1 – yes
Undefined bits are “0”
49h
0000h
Bit 0 – 4 word page, 0 – no, 1 – yes
Bit 1 – 8 word page, 0 – no, 1 – yes
Undefined bits are “0”
4Ah
0080h
Location of protection register lock byte, the section's first byte
4Bh
0003h
# of bytes in the factory prog section of prot register – 2*n
4Ch
0003h
# of bytes in the user prog section of prot register – 2*n
Bit 0 – top (“0”) or bottom (“1”) boot block device
Undefined bits are “0”
25
3441B–STKD–11/04
16-Mbit PSRAM
Description
The device is a 16-Mbit 1T/1C PSRAM featured by high-speed operation and super low
power consumption. The 16-Mbit device adopts one transistor memory cell and is organized as 1,048,576 words by 16 bits. It operates in the extended range of temperatures
and supports a wide operating voltage range. The device also supports the deep powerdown mode for a super low standby current.
Features
•
•
•
•
•
CMOS Process Technology
1M x 16-bit Organization
TTL Compatible and Tri-state Outputs
Deep Power-down: Memory Cell Data Hold Invalid
Data Mask Function by LB, UB
Product
16-Mbit
PSRAM
Note:
Voltage
[V]
2.7 ~ 3.1
Power Dissipation (Max)
Mode
(ISB1)
(IDPD)
(ICC2)
Speed
tRC [ns]
Temp.
[°C]
CS1 with
UB, LB:tOE(1)
85 µA
10 µA
25 mA
70
-30 ~ 85
1. tOE – UB, LB = High:Output Disable.
Block Diagram
ROW DECODER
A0
DATA I/O BUFFER
MEMORY ARRAY
1,024K X 16
WRITE DRIVER
26
SENSE AMP
BLOCK
DECODER
CS1
CS2
PSWE
PSOE
LB
UB
COLUMN
DECODER
PRE DECODER
ADD INPUT BUFFER
A19
I/O1
I/O8
I/O9
I/O16
CONTROL
LOGIC
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Absolute Maximum Ratings(1)
Symbol
Parameter
Rating
Unit
VIN, VOUT
Input/Output Voltage
-0.3 to VCC +0.3
V
VCC
Power Supply
-0.5 to 3.6
V
TA
Ambient Temperature
-30 to 85
°C
TSTG
Storage Temperature
-55 to 150
°C
PD
Power Dissipation
1.0
W
TSOLDER
Ball Soldering Temperature and Time
260•10
°C•sec
Note:
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is
stress rating only and the functional operation of the device under these or any other conditions above those indicated in the
operation of this specification is not implied. Exposure to the absolute maximum rating conditions for extended period may
affect reliability.
Truth Table
I/O Pin
CS2
PSWE
PSOE
LB(2)
UB
Mode
I/O1 ~ I/O8
I/O9 ~ I/O16
Power
(1)
H
X
X
X
X
Deselected
High-Z
High-Z
Standby
(1)
L
X
X
X
X
Deselected
High-Z
High-Z
Deep Power-down
(1)
H
X
X
H
H
Output Disabled
High-Z
High-Z
Active
L
H
H
H
X
X
Output Disabled
High-Z
High-Z
Active
L
H
H
L
L
H
Lower Byte Read
DOUT
High-Z
Active
L
H
H
L
H
L
Upper Byte Read
High-Z
DOUT
Active
L
H
H
L
L
L
Word Read
DOUT
DOUT
Active
L
H
L
X
L
H
Lower Byte Write
DIN
High-Z
Active
L
H
L
X
H
L
Upper Byte Write
High-Z
DIN
Active
L
H
L
X
L
L
Word Write
DIN
DIN
Active
CS1
H
X
L
Notes:
1. H = VIH, L = VIL, X = Don't Care (VIL or VIH).
2. UB, LB (Upper, Lower Byte Enable). These active LOW inputs allow individual bytes to be written or read. When LB is LOW,
data is written or read to the lower byte, I/O1 - I/O8. When UB is LOW, data is written or read to the upper byte, I/O9 I/O116.
Recommended DC Operating Condition
Symbol
Parameter
Min
Typ
Max
Unit
VCC
Supply Voltage
2.7
2.9
3.1
V
GND
Ground
0
V
VIH
Input High Voltage
VCC + 0.3
V
0.6
V
VIL
(1)
Note:
Input Low Voltage
0
2.2
(1)
-0.3
1. VIL = -1.5V for pulse width less than 10 ns. Undershoot is sampled, not 100% tested.
27
3441B–STKD–11/04
DC Electrical Characteristics
VCC = 2.7V - 3.1V, TA = -30°C to 85°C (I)
Symbol
Parameter
Test Condition
Min
Max
Unit
ILI
Input Leakage Current
GND < VIN < VCC
-1
1
µA
ILO
Output Leakage Current
GND < VOUT < VCC,
CS1 = VIH, CS2 = VIH,
PSOE = VIH or PSWE = VIL
-1
1
µA
ICC
Operating Power Supply Current
CS1 = VIL, CS2 = VIH,
VIN = VIH or VIL, II/O = 0 mA
3
mA
ICC1
Average Operating Current
CS1 < 0.2V, CS2 > VCC - 0.2V
VIN < 0.2V or VIN > VCC - 0.2V,
Cycle Time = 1 µs
100% Duty, II/O = 0 mA
5
mA
CS1 = VIL, CS2 = VIH,
VIN = VIH or VIL, Cycle Time = Min
100% Duty, II/O = 0 mA
25
mA
ICC2
ISB
TTL Standby Current
CS1, CS2 = VIH or
UB, LB = VIH
0.5
mA
ISB1
Standby Current (CMOS Input)
CS1, CS2 > VCC - 0.2V or
85
µA
IDPD
Deep Power-down Current
CS2 < GND +0.2V
10
µA
VOL
Output Low Voltage
IOL = 0.5 mA
0.3
V
VOH
Output High Voltage
IOH = -0.5 mA
VCC - 0.3
V
Capacitance(1)
(Temp = 25°C, f = 1.0 MHz)
Symbol
Parameter
CIN
COUT
Note:
28
Condition
Max
Unit
Input Capacitance (Add, CS1, CS2,
PSWE, PSOE, UB, LB)
VIN = 0V
8
pF
Output Capacitance (I/O)
VI/O = 0V
10
pF
1. These parameters are sampled and not 100% tested.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
AC Characteristics
VCC = 2.7V ~ 3.1V, TA = -30°C to 85°C (I), Unless Otherwise Specified
70 ns
#
Symbol
Parameter
Min
Max
Unit
Read Cycle
1
tRC
Read Cycle Time
2
tAA
Address Access Time
70
ns
3
tACS
Chip Select Access Time
70
ns
4
tOE
Output Enable to Output Valid
20
ns
5
tBA
LB, UB Access Time
20
ns
6
tCLZ
Chip Select to Output in Low Z
10
ns
7
tOLZ
Output Enable to Output in Low Z
5
ns
8
tBLZ
LB, UB Enable to Output in Low Z
10
ns
9
tCHZ
Chip Disable to Output in High Z
0
10
ns
10
tOHZ
Out Disable to Output in High Z
0
10
ns
11
tBHZ
LB, UB Disable to Output in High Z
0
10
ns
12
tOH
Output Hold from Address Change
5
ns
13
tWC
Write Cycle Time
70
ns
14
tCW
Chip Selection to End of Write
60
ns
15
tAW
Address Valid to End of Write
60
ns
16
tBW
LB, UB Valid to End of Write
60
ns
17
tAS
Address Setup Time
0
ns
18
tWP
Write Pulse Width
50
ns
19
tWR
Write Recovery Time
0
ns
20
tWHZ
Write to Output in High Z
0
21
tDW
Data to Write Time Overlap
30
ns
22
tDH
Data Hold from Write Time
0
ns
23
tOW
Output Active from End of Write
5
ns
70
ns
Write Cycle
20
ns
AC Test Conditions
TA = -30°C to 85°C (M), Unless Otherwise Specified
Parameter
Value
Input Pulse Level
0.4V to 2.2V
Input Rising and Fall Time
5 ns
Input and Output Timing Reference Level
0.5 * VCC
Output Load
(See AC Test Loads Figure on page 30)
29
3441B–STKD–11/04
AC Test Loads
RL = 50 Ohm
DOUT
VL = 0.5*VCCQ
(1)
Z0 = 50 Ohm
Note:
Power-up Sequence
CL = 50 pF
Including jig and scope capacitance.
1. Supply power.
2. Maintain stable power for longer than 200 µs.
Deep Power-down
Entry Sequence
1. Keep CS2 low state. Deep Power-down mode is maintained while CS2 is low
state.
Deep Power-down
Exit Sequence
1. Keep CS2 high state.
2. Maintain stable power for longer than 200 µs.
State Diagram
Power On
Power-up
Sequence
Wait 200 µs
CS2 = VIH
Deep Power-down
Exit Sequence
Active
CS1 = VIL, CS2 = VIH
CS2 = VIL
CS2 = VIH, CS1 = VIH
Standby
Mode
Deep Powerdown Mode
CS2 = VIL
Deep Power-down
Entry Sequence
Standby Mode Characteristics
Mode
Standby
Deep Power-down
30
Memory Cell Data
Standby Current [µA]
Wait Time [µs]
Valid
85
0
Invalid
10
200
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Timing Diagrams
Power-up Sequence Timing
Wait 200 µs
Normal Operation
VCC
CS2
CS1
Note:
Power-up time is defined when CS2 is kept high before VCC reaches specified minimum level. In case of CS2 is switched from
low level to high level, after VCC reached specified level, it is defined as the deep power-down exit.
Deep Power-down Entry/Exit Sequence Timing
Suspend
1 µs
Deep Power-down Mode
Wait 200 µs
Normal Operation
CS2
CS1
Note:
When switching CS2 from high level to low level, the device will be in the deep power-down. In this case, an internal refresh
stops and the data might be lost.
Standby Mode Characteristics Timing
tRC
Standby Mode
CS1
ISB1
Deep Power-down Mode Characteristics Timing
Suspend 1 µs
Deep Power-down Mode
CS2
IDPD
31
3441B–STKD–11/04
Read Cycle 1(1),(4)
tRC
ADDRESS
tAA
tOH
tACS
CS1
tCHZ(3)
CS2
VIH
tBA
UB, LB
tBHZ(3)
tOE
PSOE
tOHZ (3)
tOLZ(3)
tBLZ(3)
tCLZ(3)
DATA OUT
HIGH-Z
DATA VALID
Read Cycle 2, CS2 = VIH(1),(2),(4)
tRC
ADDRESS
tAA
tOH
tOH
DATA OUT
DATA VALID
PREVIOUS DATA
Read Cycle 3, CS2 = VIH(1),(2),(4)
CS1
tACS
tCLZ
DATA OUT
Notes:
32
HIGH-Z
tCHZ (3)
(3)
DATA VALID
1. Read Cycle occurs whenever a high on the PSWE and PSOE is low, while UB and/or LB and CS1 and CS2 are in
active status.
2. PSOE = VIL.
3. The tCHZ, tBHZ and tOHZ are defined as the time at which the outputs achieve the high impedance state and tOLZ, tBLZ and tCLZ
are defined as the time at which the outputs achieve the low impedance state. These are not referenced to output
voltage levels.
4. CS1 in high for the standby, low for active.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Write Cycle 1 (PSWE Controlled)(1),(4),(5),(9),(10)
tWC
ADDRESS
tWR(2)
tCW
CS1
CS2
tAW
VIH
tBW
UB,LB
tWP
PSWE
DATA IN
tAS
tDW
HIGH-Z
tDH
DATA VALID
tWHZ(3)(8)
tOW
(6)
(7)
DATA OUT
Write Cycle 2 (CS1 Controlled)(1),(4),(5),(9),(10)
tWC
ADDRESS
tAS
tWR(2)
tCW
CS1
CS2
VIH
tAW
tBW
UB, LB
tWP
PSWE
tDW
DATA IN
DATA OUT
Notes:
HIGH-Z
tDH
DATA VALID
HIGH-Z
1. A write occurs during the overlap of a low CS1, a low PSWE, and a low UB or LB.
2. tWR is measured from the earlier of CS1 or PSWE going high to the end of write cycle.
3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the output must not be
applied.
4. If the CS1, LB and UB low transition occur simultaneously with the PSWE low transition or after the PSWE transition, outputs remain in a high impedance state.
5. PSOE is continuously low (PSOE = VIL).
6. Q (data out) is the invalid data.
7. Q (data out) is the read data of the next address.
8. The tWHZ is defined as the time at which the outputs achieves the high impedance state. It is not referenced to output voltage
levels.
9. CS1 in high for the standby, low for active.
10. Do not input data to the I/O pins while they are in the output state.
33
3441B–STKD–11/04
Write Cycle 3 (LB, UB Controlled)
tWC
ADDRESS
tWR
tCW
CS1
CS2
tAS
tAW
VIH
tWR
tAS
UB, LB
tAS
PSWE
tBA
tWP
tDW
DATA IN
Notes:
34
HIGH-Z
tDH
DATA VALID
1. The tBW is specified from the time satisfied both tAS and tWR.
2. Although UB and LB are high state, it’s illegal function to change address both CS and PSWE are in low state.
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Avoid Timing
The 16-Mbit PSRAM has a timing which is not supported at read operation. If your system has multiple invalid address signal shorter than t RC during over 48 µs at read
operation which showed in abnormal timing, it needs a normal read timing at least during 48 µs which showed in Avoidable Timing(1) or toggle the CS1 to high (> tRC) one
time at least which showed in Avoidable Timing(2)
Abnormal Timing
CS1
> 48 µs
PSWE
< tRC
ADDRESS
Avoidable Timing (1)
CS1
> 48 µs
PSWE
> tRC
ADDRESS
Avoidable Timing (2)
> tRC
CS1
> 48 µs
PSWE
< tRC
ADDRESS
35
3441B–STKD–11/04
Ordering Information
tACC
(ns)
Flash Boot
Block
PSRAM
Package
Operation Range
AT52BC6402A-70CI
Bottom
1M x 16
66C6
Industrial
(-40° to 85°C)
AT52BC6402AT-70CI
Top
1M x 16
66C6
Industrial
(-40° to 85°C)
AT52BC6402A-85CI
Bottom
1M x 16
66C6
Industrial
(-40° to 85°C)
AT52BC6402AT-85CI
Top
1M x 16
66C6
Industrial
(-40° to 85°C)
Ordering Code
70
85
Package Type
66C6
36
66-ball, Plastic Chip-size Ball Grid Array Package (CBGA)
AT52BC6402A(T)
3441B–STKD–11/04
AT52BC6402A(T)
Packaging Information
66C6 – CBGA
0.12 C
D
C Seating Plane
Marked A1 Identifier
Side View
E
A1
Top View
1.10 REF
A
D1
12 11
10
9
8
7
6
A1 Ball Corner
4
5
3
2
1
A
e
B
C
D
E1
E
F
G
COMMON DIMENSIONS
(Unit of Measure = mm)
H
1.20 REF
e
Øb
Bottom View
MIN
NOM
MAX
A
–
–
1.0
A1
0.17
–
–
D
10.90
11.00
11.10
SYMBOL
D1
E
NOTE
8.80 TYP
7.90
8.00
8.10
E1
5.60 TYP
e
0.80 TYP
Øb
0.40 TYP
08/27/03
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
66C6, 66-ball (12 x 8 Array), 11 x 8 x 1.0 mm Body, 0.8 mm Ball
Pitch Chip-scale Ball Grid Array Package (CBGA)
DRAWING NO.
66C6
REV.
A
37
3441B–STKD–11/04
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© Atmel Corporation 2004. All rights reserved. Atmel ®, logo and combinations thereof, are registered trademarks, and Everywhere You Are SM
are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
3441B–STKD–11/04
xM