TI TPS62142RGTR

TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
3-V to 17-V 2-A Step-Down Converter in 3x3 QFN Package
Check for Samples: TPS62140, TPS62140A, TPS62141, TPS62142, TPS62143
FEATURES
DESCRIPTION
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The TPS6214X family is an easy-to-use synchronous
step-down dc-dc converter optimized for applications
with high power density. A high switching frequency
of typically 2.5MHz allows the use of small inductors
and provides fast transient response by use of the
DCS-Control™ topology.
TM
DCS-Control Topology
Input Voltage Range: 3 V to 17 V
Up to 2-A Output Current
Adjustable Output Voltage from 0.9 V to 6 V
Pin-Selectable Output Voltage (Nominal, +5%)
Programmable Soft Start and Tracking
Seamless Power-Save Mode Transition
Quiescent Current of 17 µA (typ.)
Selectable Operating Frequency
Power-Good Output
100% Duty-Cycle Mode
Short-Circuit Protection
Over Temperature Protection
Available in a 3-mm × 3-mm, QFN-16 Package
With its wide operating input voltage range of 3V to
17V, the devices are ideally suited for systems
powered from either a Li-Ion or other batteries, as
well as from 12-V intermediate power rails. It
supports up to 2A of continuous output current at
output voltages between 0.9V and 6V (with 100%
duty-cycle mode).
The output voltage start-up ramp is controlled by the
soft-start pin, which allows operation as either a
standalone power supply or in tracking configurations.
Power sequencing is also possible by configuring the
Enable (EN) and open-drain Power Good (PG) pins.
APPLICATIONS
•
•
•
•
•
•
In power-save mode, the devices show quiescent
current of about 17μA from VIN. Power Save Mode,
entered automatically and seamlessly if load is small,
maintains high efficiency over the entire load range.
In Shutdown Mode, the device is turned off and
shutdown current consumption is less than 2μA.
Standard 12-V Rail Supplies
POL Supply From Single or Multiple Li-Ion
Battery
Solid-State Disk Drives
Embedded Systems
LDO Replacement
Mobile PCs, Tablet, Modems, Cameras
The device, available in adjustable and fixed output
voltage versions, is packaged in a 16-pin QFN
package measuring 3 × 3 mm (RGT).
spacing
(3 .. 17)V
1.8V / 2A
2.2 µH
10uF
PVIN
SW
AVIN
VOS
PG
EN
100k
22uF
TPS62141
SS/TR
3.3nF
FB
DEF
AGND
FSW
PGND
Figure 1. Typical Application and Efficiency
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2013, Texas Instruments Incorporated
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1)
TA
OUTPUT VOLTAGE
PART NUMBER (2)
adjustable
TPS62140
TPS62140RGT
QTZ
adjustable
TPS62140A (3)
TPS62140ARGT
PA7I
1.8 V
TPS62141
TPS62141RGT
QWA
3.3 V
TPS62142
TPS62142RGT
QWB
5V
TPS62143
TPS62143RGT
QWC
–40°C to 85°C
(1)
(2)
(3)
PACKAGE
16-Pin QFN
ORDERING
PACKAGE MARKING
For detailed ordering information, see the PACKAGE OPTION ADDENDUM section at the end of this data sheet.
Contact the factory to check availability of other fixed output voltage versions.
While TPS6214X has PG=High Z, TPS62140A features PG=Low, when device is in shutdown through EN, UVLO or Thermal Shutdown.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
Pin voltage range
(2)
Power-good sink current
Temperature range
ESD rating (3)
(1)
(2)
(3)
MAX
AVIN, PVIN
–0.3
20
EN, SS/TR
–0.3
VIN+0.3
SW
–0.3
VIN+0.3
DEF, FSW, FB, PG, VOS
–0.3
PG
V
7
V
mA
–40
125
Storage temperature range, Tstg
–65
150
CDM Charged-device model
V
10
Operating junction temperature range, TJ
HBM Human-body model
UNIT
°C
2
kV
0.5
kV
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to network ground terminal.
ESD testing is performed according to the respective JESD22 JEDEC standard.
THERMAL INFORMATION
THERMAL METRIC (1)
TPS6214X
θJA
Junction-to-ambient thermal resistance
θJC(TOP)
Junction-to-case(top) thermal resistance
θJB
Junction-to-board thermal resistance
11
ψJT
Junction-to-top characterization parameter
0.5
ψJB
Junction-to-board characterization parameter
10
θJC(BOTTOM)
Junction-to-case(bottom) thermal resistance
3.5
(1)
UNITS
RGT 16 PINS
29.1
15
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
Supply voltage, VIN (at AVIN and P VIN)
TYP
MAX
UNIT
3
17
V
Operating free-air temperature, TA
–40
85
°C
Operating junction temperature, TJ
–40
125
°C
2
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
ELECTRICAL CHARACTERISTICS
over free-air temperature range (TA=-40°C to +85°C), typical values at VIN=AVIN=PVIN=12V and TA=25°C (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
Input voltage range (1)
VIN
3
IQ
Operating quiescent current
EN = High, IOUT = 0 mA, device not
switching
ISD
Shutdown current (2)
EN = Low
VUVLO
TSD
Undervoltage lockout threshold
Falling input voltage
2.6
Hysteresis
17
V
17
25
µA
1.5
4
µA
2.7
2.8
200
Thermal shutdown temperature
160
Thermal shutdown hysteresis
V
mV
°C
20
CONTROL (EN, DEF, FSW, SS/TR, PG)
VH
High-level input threshold voltage (EN, DEF,
FSW)
VL
Low-level input threshold voltage (EN, DEF,
FSW)
ILKG
Input leakage current (EN, DEF, FSW)
VTH_PG
Power-good threshold voltage
VOL_PG
Power-good output low
IPG= –2 mA
ILKG_PG
Input leakage current (PG)
VPG = 1.8 V
ISS/TR
SS/TR pin source current
0.9
EN, DEF, FSW = VIN or GND
V
0.3
V
0.01
1
µA
Rising (%VOUT)
92
95
98
Falling (%VOUT)
87
90
93
0.07
0.3
%
V
1
400
nA
2.5
2.7
µA
VIN ≥ 6 V
90
170
VIN = 3 V
120
VIN ≥ 6 V
40
VIN = 3 V
50
2.3
POWER SWITCH
High-side MOSFET ON-resistance
rDS(on)
Low-side MOSFET ON-resistance
ILIMF
High-side MOSFET forward current limit (3)
VIN = 12 V, TA = 25°C
2.45
3
70
3.5
mΩ
mΩ
A
OUTPUT
VREF
Internal reference voltage (4)
ILKG_FB
Input leakage current (FB)
TPS62140, VFB = 0.8 V
Output voltage range (TPS62140)
VIN ≥ VOUT
DEF (output voltage programming)
DEF = 0 (GND)
VOUT
DEF = 1 (VOUT)
VOUT + 5%
VOUT
(1)
(2)
(3)
(4)
(5)
(6)
Initial output voltage accuracy
0.8
(5)
1
0.9
V
100
nA
6.0
V
PWM mode operation, VIN ≥ VOUT + 1 V
–1.8
1.8
PWM mode operation, VIN ≥ VOUT +1 V,
TA = –10°C to 85°C
-1.5
1.6
Power-save mode operation, COUT=22µF
–2.3
%
2.8
Load regulation (6)
VIN = 12 V, VOUT = 3.3 V, PWM mode
operation
0.05
%/A
Line regulation (6)
3 V ≤ VIN ≤ 17 V, VOUT = 3.3 V, IOUT = 1 A,
PWM mode operation
0.02
%/V
The device is still functional down to undervoltage lockout (see parameter VUVLO).
Current into AVIN + PVIN pins
This is the static current limit. It can be temporarily higher in applications due to internal propagation delay (see Current Limit and Short
Circuit Protection section).
This is the voltage regulated at the FB pin.
This is the accuracy provided by the device itself (line and load regulation effects are not included). For the fixed-voltage versions the
(internal) resistive divider is included.
Line and load regulation depend on external component selection and layout (see Figure 17 and Figure 18).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
3
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
DEVICE INFORMATION
SW
3
PG
4
PGND
VOS
EN
13
Exposed
Thermal Pad
5
6
7
8
DEF
2
14
FSW
SW
15
AGND
1
16
FB
SW
PGND
RGT PACKAGE
(TOP VIEW)
12
PVIN
11
PVIN
10
AVIN
9
SS/TR
Terminal Functions
PIN (1)
NAME
NO.
I/O
DESCRIPTION
SW
1, 2 ,3
O
Switch node, which is connected to the internal MOSFET switches. Connect inductor between SW and
output capacitor.
PG
4
O
Output power-good (High = VOUT ready, Low = VOUT below nominal regulation); open-drain (requires
pullup resistor; goes high-impedance when device is switched off)
FB
5
I
Voltage feedback of adjustable version. Connect resistive voltage divider to this pin. Its recommended to
connect FB to AGND on fixed output-voltage versions for improved thermal performance.
AGND
6
–
Analog ground. Must be connected directly to the Exposed Thermal Pad and common ground plane.
FSW
7
I
Switching frequency select (Low ≈ 2.5 MHz, High ≈ 1.25 MHz (2) for typical operation) (3)
DEF
8
I
Output voltage scaling (Low = nominal, High = nominal + 5%) (3)
SS/TR
9
I
Soft-start / tracking pin. An external capacitor connected to this pin sets the internal voltage-reference rise
time. It can be used for tracking and sequencing.
AVIN
10
I
Supply voltage for control circuitry. Connect to same source as PVIN.
PVIN
11, 12
I
Supply voltage for power stage. Connect to same source as AVIN.
13
I
Enable input (High = enabled, Low = disabled) (3)
14
I
Output-voltage sense pin and connection for the control loop circuitry.
15, 16
–
Power ground. Must be connected directly to the Exposed Thermal Pad and common ground plane.
–
Must be connected to AGND (pin 6), PGND (pin 15,16) and common ground plane (4). Must be soldered
to achieve appropriate power dissipation and mechanical reliability.
EN
VOS
PGND
Exposed
thermal pad
(1)
(2)
(3)
(4)
4
For more information about connecting pins, see the DETAILED DESCRIPTION and APPLICATION INFORMATION sections.
Connect FSW to VOUT or PG in this case.
An internal pulldown resistor keeps the logic level low, if pin is floating.
See Figure 41.
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
FUNCTIONAL BLOCK DIAGRAM
PG
Soft
start
Thermal
Shtdwn
UVLO
AVIN
PVIN PVIN
PG control
HS lim
comp
EN*
SW
SS/TR
power
control
control logic
gate
drive
SW
DEF*
SW
FSW*
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND PGND
Figure 2. TPS62140 (Adjustable Output Voltage)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
5
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
PG
Soft
start
Thermal
Shtdwn
UVLO
AVIN
PVIN PVIN
PG control
HS lim
comp
EN*
SW
SS/TR
power
control
control logic
DEF
gate
drive
SW
*
SW
FSW*
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB*
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND PGND
Figure 3. TPS62141/2/3 (Fixed Output Voltage)
6
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
PARAMETER MEASUREMENT INFORMATION
List of Components
REFERENCE
DESCRIPTION
IC
17-V, 2-A step-down converter, QFN
MANUFACTURER
L1
2.2-µH, 3.1-A, 0.165 in × 0.165 in
Cin
10-µF, 25-V, ceramic
Standard
Cout
22-µF, 6.3-V, ceramic
Standard
Cs
3300-pF, 25-V, ceramic
R1
Dependent on Vout
R2
Dependent on Vout
R3
100-kΩ, chip, 0603, 1/16W, 1%
TPS62140RGT, Texas Instruments
XFL4020-222MEB, Coilcraft
Standard
L1
VIN
CIN
VOUT
SW
VIN
AVIN
VOS
EN
PG
FB
R3
COUT
R1
TPS62140
SS/TR
CSS
FB
PG
DEF
AGND
FSW
PGND
R2
Figure 4. Measurement Setup
TYPICAL CHARACTERISTICS
Table of Graphs
DESCRIPTION
FIGURE
Efficiency
vs Output Current, vs Input Voltage
5–16
Output voltage
vs Output current (Load regulation), vs Input Voltage
(Line regulation)
17, 18
vs Input Voltage
19
vs Output Current
20
Quiescent Current
vs Input Voltage
21
Shutdown Current
vs Input Voltage
Power FET RDS(on)
vs Input Voltage (High-Side, Low-Side)
Output Voltage Ripple
vs output Current
Maximum Output Current
vs Input Voltage
Power Supply Rejection Ratio (PSSR)
vs Frequency
Switching Frequency
22
25
26
27, 28
PWM-PSM-PWM Mode Transition
Waveforms
Maximum Ambient Temperature
Copyright © 2011–2013, Texas Instruments Incorporated
23, 24
29
Load Transient Response
30–32
Start-Up
33, 34
Typical PWM Mode Operation
35
Typical Power Save Mode Operation
36
vs Load Current
37
vs Power Dissipation
38
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
7
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
EFFICIENCY
vs
OUTPUT CURRENT
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
70.0
VIN=12V
VIN=17V
Efficiency (%)
Efficiency (%)
80.0
60.0
50.0
40.0
30.0
0.0
0.0001
IOUT=1mA
IOUT=1A
IOUT=100mA
40.0
0.001
0.01
0.1
Output Current (A)
1
VOUT=5.0V
L=2.2uH (XFL4020)
Cout=22uF
10.0
0.0
10
7
8
9
10
G001
11
12
13
Input Voltage (V)
14
15
16
Figure 6. Efficiency With 1.25 MHz, Vout = 5 V
EFFICIENCY
vs
OUTPUT CURRENT
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
80.0
70.0
70.0
60.0
VIN=17V
50.0
VIN=12V
40.0
30.0
60.0
IOUT=10mA
50.0
IOUT=1mA
17
G001
Figure 5. Efficiency With 1.25 MHz, Vout = 5 V
Efficiency (%)
Efficiency (%)
IOUT=10mA
50.0
20.0
VOUT=5.0V
L=2.2uH (XFL4020)
Cout=22uF
10.0
IOUT=1A
IOUT=100mA
40.0
30.0
20.0
0.0
0.0001
0.001
0.01
0.1
Output Current (A)
1
VOUT=5.0V
L=2.2uH (XFL4020)
Cout=22uF
20.0
VOUT=5.0V
L=2.2uH (XFL4020)
Cout=22uF
10.0
10.0
0.0
10
7
8
9
10
G001
11
12
13
Input Voltage (V)
14
15
16
Figure 8. Efficiency With 2.5 MHz, Vout = 5 V
EFFICIENCY
vs
OUTPUT CURRENT
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
80.0
70.0
VIN=12V
60.0
VIN=17V
VIN=5V
50.0
40.0
30.0
17
G001
Figure 7. Efficiency With 2.5 MHz, Vout = 5 V
Efficiency (%)
Efficiency (%)
60.0
30.0
20.0
70.0
60.0
IOUT=1A IOUT=100mA
IOUT=10mA
IOUT=1mA
50.0
40.0
30.0
20.0
0.0
0.0001
0.001
0.01
0.1
Output Current (A)
1
Figure 9. Efficiency With 1.25 MHz, Vout = 3.3 V
Submit Documentation Feedback
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
20.0
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
10.0
8
70.0
10.0
10
G001
0.0
4
5
6
7
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 10. Efficiency With 1.25 MHz, Vout = 3.3 V
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
80.0
70.0
70.0
60.0
VIN=12V
50.0
Efficiency (%)
Efficiency (%)
EFFICIENCY
vs
OUTPUT CURRENT
VIN=17V
VIN=5V
40.0
30.0
IOUT=1mA
IOUT=10mA
IOUT=1A
40.0
0.0
0.0001
0.001
0.01
0.1
Output Current (A)
1
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
20.0
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
10.0
10.0
0.0
10
4
5
6
7
8
G001
9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 11. Efficiency With 2.5 MHz, Vout = 3.3 V
Figure 12. Efficiency With 2.5 MHz, Vout = 3.3 V
EFFICIENCY
vs
OUTPUT CURRENT
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
80.0
70.0
VIN=12V
60.0
50.0
Efficiency (%)
Efficiency (%)
IOUT=100mA
50.0
30.0
20.0
VIN=17V
VIN=5V
40.0
30.0
IOUT=1A
60.0
IOUT=100mA
50.0
IOUT=10mA
IOUT=1mA
40.0
0.001
0.01
0.1
Output Current (A)
1
VOUT=1.8V
L=2.2uH (XFL4020)
Cout=22uF
20.0
VOUT=1.8V
L=2.2uH (XFL4020)
Cout=22uF
10.0
0.0
0.0001
70.0
30.0
20.0
10.0
0.0
10
3
4
5
6
7
G001
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 13. Efficiency With 1.25 MHz, Vout = 1.8 V
Figure 14. Efficiency With 1.25 MHz, Vout = 1.8 V
EFFICIENCY
vs
OUTPUT CURRENT
EFFICIENCY
vs
INPUT VOLTAGE
100.0
100.0
90.0
90.0
80.0
80.0
70.0
60.0
VIN=12V
Efficiency (%)
Efficiency (%)
60.0
VIN=17V
50.0
VIN=5V
40.0
30.0
60.0
IOUT=1A
50.0
IOUT=100mA
40.0
IOUT=10mA
IOUT=1mA
30.0
20.0
0.001
0.01
0.1
Output Current (A)
1
Figure 15. Efficiency With 1.25 MHz, Vout = 0.9 V
Copyright © 2011–2013, Texas Instruments Incorporated
VOUT=0.9V
L=2.2uH (XFL4020)
Cout=22uF
20.0
VOUT=0.9V
L=2.2uH (XFL4020)
Cout=22uF
10.0
0.0
0.0001
70.0
10.0
10
G001
0.0
3
4
5
6
7
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 16. Efficiency With 1.25 MHz, Vout = 0.9 V
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
9
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
3.40
3.40
Output Voltage (V)
Output Voltage (V)
VIN=17V
3.35
VIN=12V
3.30
VIN=5V
3.25
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
3.20
0.0001
0.001
0.01
0.1
Output Current (A)
1
3.25
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
4
7
10
13
Input Voltage (V)
16
G001
Figure 18. Output Voltage Accuracy (Line Regulation)
SWITCHING FREQUENCY
vs
INPUT VOLTAGE
SWITCHING FREQUENCY
vs
OUTPUT CURRENT
4
3.5
Switching Frequency (MHz)
IOUT=2A
3
2.5
2
IOUT=0.5A
IOUT=1A
1.5
1
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
0.5
0
4
6
8
10
12
Input Voltage (V)
14
16
3
2.5
2
1.5
1
0
18
0
0.5
1
Output Current (A)
G000
1.5
Figure 20. Switching Frequency
INPUT CURRENT
vs
INPUT VOLTAGE
INPUT CURRENT
vs
INPUT VOLTAGE
5.0
45.0
4.5
40.0
4.0
35.0
30.0
25°C
25.0
85°C
20.0
15.0
10.0
3.5
85°C
3.0
2.5
2.0
1.5
1.0
−40°C
5.0
3.0
6.0
9.0
12.0
Input Voltage (V)
−40°C
25°C
0.5
15.0
Figure 21. Quiescent Current
Submit Documentation Feedback
2
G000
Figure 19. Switching Frequency
50.0
0.0
0.0
VIN=12V, VOUT=3.3V
L=2.2uH (XFL4020)
FSW=Low
0.5
Input Current (µA)
Switching Frequency (MHz)
IOUT=100mA
Figure 17. Output Voltage Accuracy (Load Regulation)
3.5
Input Current (µA)
IOUT=1A
G001
4
10
IOUT=10mA
3.30
3.20
10
IOUT=1mA
3.35
18.0 20.0
G001
0.0
0.0
3.0
6.0
9.0
12.0
Input Voltage (V)
15.0
18.0 20.0
G001
Figure 22. Shutdown Current
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
STATIC DRAIN-SOURCE-RESISTANCE (RDSon)
vs
INPUT VOLTAGE
STATIC DRAIN-SOURCE-RESISTANCE (RDSon)
vs
INPUT VOLTAGE
100.0
200.0
160.0
125°C
RDSon Low−Side (mΩ)
RDSon High−Side (mΩ)
180.0
140.0
120.0
85°C
100.0
25°C
80.0
−10°C
60.0
−40°C
40.0
80.0
125°C
60.0
85°C
25°C
40.0
−10°C
20.0
−40°C
20.0
0.0
0.0
3.0
6.0
9.0
12.0
Input Voltage (V)
15.0
0.0
0.0
18.0 20.0
6.0
9.0
12.0
Input Voltage (V)
OUTPUT CURRENT
vs
INPUT VOLTAGE
4
Output Current (A)
VIN=17V
−40°C
3.5
VOUT=3.3V,
L=2.2uH (XFL4020)
Cout=22uF
VIN=5V
0.02
2.5
2
85°C
1.5
1
0.01
VOUT=3.3V
L=2.2uH (XFL4020)
Cout=22uF
VIN=12V
0
0.2
0.4
0.6
0.8
1
1.2 1.4
Output Current (A)
1.6
1.8
0
2
25°C
3
0.5
4
5
6
7
G000
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
G000
Figure 25. Output Voltage Ripple
Figure 26. Maximum Output Current
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
100
100
90
VIN=12V
90
VIN=5V
80
VIN=5V
80
VIN=12V
70
70
VIN=17V
PSRR (dB)
PSRR (dB)
G001
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
0.03
60
50
40
30
VIN=17V
60
50
40
30
20
20
VOUT=3.3V, IOUT=1A
L=2.2uH (XFL4020)
Cin=10uF, Cout=22uF
10
0
18.0 20.0
Figure 24. Low-Side Switch Resistance
0.04
0
15.0
Figure 23. High-Side Switch Resistance
0.05
Output Voltage Ripple (V)
3.0
G001
10
100
1k
10k
Frequency (Hz)
100k
1M
G000
Figure 27. Power-Supply Rejection Ratio, fSW = 2.5 MHz
Copyright © 2011–2013, Texas Instruments Incorporated
VOUT=3.3V, IOUT=0.1A
L=2.2uH (XFL4020)
Cin=10uF, Cout=22uF
10
0
10
100
1k
10k
Frequency (Hz)
100k
1M
G000
Figure 28. Power-Supply Rejection Ratio, fSW = 2.5 MHz
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
11
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
12
www.ti.com
OUTPUT VOLTAGE
vs
TIME
OUTPUT VOLTAGE
vs
TIME
Figure 29. PWM-PSM-Transition (VIN=12 V, VOUT = 3.3 V With
50 mV/div)
Figure 30. Load Transient Response (IOUT= 0.5 to 2 to 0.5 A,
VIN = 12 V, VOUT = 3.3 V)
OUTPUT VOLTAGE
vs
TIME
OUTPUT VOLTAGE
vs
TIME
Figure 31. Line Transient Response of Figure 30, Rising
Edge
Figure 32. Line Transient Response of Figure 30, Falling
Edge
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
OUTPUT VOLTAGE
vs
TIME
OUTPUT VOLTAGE
vs
TIME
Figure 33. Start-Up Into 100 mA (VIN = 12 V, VOUT = 3.3 V)
Figure 34. Start-Up into 2 A (VIN = 12 V, VOUT = 3.3 V)
PWM SIGNALS
vs
TIME
POWER SAVE MODE SIGNALS
vs
TIME
Figure 35. Typical Operation in PWM Mode (IOUT = 1 A)
Figure 36. Typical Operation in Power-Save Mode (IOUT = 10
mA)
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
13
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
AMBIENT TEMPERATURE
vs
OUTPUT CURRENT
AMBIENT TEMPERATURE
vs
OUTPUT POWER
125
Free−Air Temperature (°C)
Free−Air Temperature (°C)
125
115
105
95
TPS62140 EVM
L=2.2uH (XFL4020)
VIN=12V, VOUT=3.3V
85
75
0
0.5
1
1.5
Output Current (A)
Submit Documentation Feedback
105
95
85
75
TPS62140 EVM
L=2.2uH (XFL4020)
VIN=12V, VOUT=3.3V
65
2
2.5
G000
Figure 37. Maximum Ambient Temperature (fSW = 2.5 MHz)
14
115
55
0
2
4
6
8
Output Power (W)
10
12
G000
Figure 38. Maximum Ambient Temperature (fSW = 2.5 MHz)
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
DETAILED DESCRIPTION
Device Operation
The TPS6214X synchronous switched-mode power converters are based on DCS-Control™ (Direct Control with
Seamless Transition into Power-Save Mode), an advanced regulation topology, that combines the advantages of
hysteretic, voltage-mode and current-mode control including an ac loop directly associated with the output
voltage. This control loop takes information about output voltage changes and feeds it directly to a fast
comparator stage. It sets the switching frequency, which is constant for steady-state operating conditions, and
provides immediate response to dynamic load changes. To get accurate dc load regulation, a voltage feedback
loop is used. The internally compensated regulation network achieves fast and stable operation with small
external components and low-ESR capacitors.
The DCS-Control topology supports pulse-width modulation (PWM) mode for medium and heavy load conditions
and a power-save mode at light loads. During PWM, it operates at its nominal switching frequency in continuousconduction mode. This frequency is typically about 2.5 MHz with a controlled frequency variation depending on
the input voltage. If the load current decreases, the converter enters power-save mode to sustain high efficiency
down to very light loads. In power-save mode, the switching frequency decreases linearly with the load current.
Because DCS-Control supports both operation modes within one single building block, the transition from PWM
to power-save mode is seamless without effects on the output voltage.
Fixed output-voltage versions provide the smallest solution size and lowest current consumption, requiring only 3
external components. An internal current limit supports nominal output currents of up to 2A.
The TPS6214X family offers both excellent dc voltage and superior load transient regulation, combined with very
low output voltage ripple, minimizing interference with RF circuits.
Pulse-Width Modulation (PWM) Operation
The TPS6214X operates with pulse-width modulation in continuous-conduction mode (CCM) with a nominal
switching frequency of 2.5 MHz or 1.25 MHz, selectable with the FSW pin. The frequency variation in PWM is
controlled and depends on VIN, VOUT and the inductance. The device operates in PWM mode as long the output
current is higher than half the inductor ripple current. To maintain high efficiency at light loads, the device enters
power-save mode at the boundary to discontinuous conduction mode (DCM). This happens if the output current
becomes smaller than half the inductor ripple current.
Power-Save Mode Operation
The TPS6214X enters its built-in power-save mode seamlessly if the load current decreases. This secures a high
efficiency in light-load operation. The device remains in power-save mode as long as the inductor current is
discontinuous.
In power-save mode, the switching frequency decreases linearly with the load current, maintaining high
efficiency. The transition into and out of power-save mode happens within the entire regulation scheme and is
seamless in both directions.
TPS6214X includes a fixed-on-time circuit. The on-time, in steady-state operation, can be estimated as:
t ON =
VOUT
× 400ns
V IN
(1)
For very small output voltages, an absolute minimum on-time of about 80 ns is kept to limit switching losses. The
operating frequency is thereby reduced from its nominal value, which keeps efficiency high. Using tON, the typical
peak inductor current in power-save mode can be approximated by:
I LPSM ( peak ) =
(V IN - VOUT )
× t ON
L
(2)
When VIN decreases to typically 15% above VOUT, the TPS6214X does not enter power-save mode, regardless
of the load current. The device maintains output regulation in PWM mode.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
15
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
100% Duty-Cycle Operation
The duty cycle of the buck converter is given by D = Vout/Vin and increases as the input voltage comes close to
the output voltage. In this case, the device starts 100% duty-cycle operation, turning on the high-side switch
100% of the time. The high-side switch stays turned on as long as the output voltage is below the internal
setpoint. This allows the conversion of small input-to-output voltage differences, e.g., for longest operation time
of battery-powered applications. In 100% duty-cycle mode, the low-side FET is switched off.
The minimum input voltage to maintain output voltage regulation, depending on the load current and the output
voltage level, can be calculated as:
VIN (min) = VOUT (min) + I OUT (RDS ( on ) + RL )
(3)
where
IOUT is the output current.
RDS(on) is the RDS(on) of the high-side FET.
RL is the dc resistance of the inductor used.
Enable / Shutdown (EN)
When the enable pin (EN) is set High, the device starts operation.
Shutdown is forced if EN is pulled Low with a shutdown current of typically 1.5 µA. During shutdown, the internal
power MOSFETs as well as the entire control circuitry are turned off. The internal resistive divider pulls down the
output voltage smoothly. An internal pulldown resistor of about 400 kΩ is connected and keeps EN logic Low if
the pin is floating. It is disconnected if the pin is High.
Connecting the EN pin to an appropriate output signal of another power rail provides sequencing of multiple
power rails.
Soft-Start / Tracking (SS/TR)
The internal soft-start circuitry controls the output voltage slope during start-up. This avoids excessive inrush
current and ensures a controlled output-voltage rise time. It also prevents unwanted voltage drops from highimpedance power sources or batteries. When EN is set to start device operation, the device starts switching after
a delay of about 50 µs, and VOUT rises with a slope controlled by an external capacitor connected to the SS/TR
pin. See Figure 33 and Figure 34 for typical start-up operation.
The slope can be controlled by an external capacitor connected to the SS/TR pin. Connecting SS/TR directly to
AVIN provides fastest start-up behavior. The TPS6214X can start into a pre-biased output. During monotonic
pre-biased startup, both the power MOSFETs are not allowed to turn on until the device internal ramp sets an
output voltage above the pre-bias voltage. As long as the output is below about 0.5 V, a reduced current limit of
typically 1.6 A is set internally. If the device is set to shutdown (EN = GND), undervoltage lockout, or thermal
shutdown, an internal resistor pulls the SS/TR pin down to ensure a proper low level. Returning from those states
causes a new start-up sequence as set by the SS/TR connection.
A voltage supplied to SS/TR can be used for tracking a master voltage. The output voltage follows this voltage in
both directions, up and down (see APPLICATION INFORMATION).
Current Limit and Short Circuit Protection
The TPS6214X devices are protected against heavy load and short-circuit events. If a short circuit is detected
(VOUT drops below 0.5 V), the current limit is reduced to 1.6 A, typically. If the output voltage rises above 0.5 V,
the device runs in normal operation again. At heavy loads, the current limit determines the maximum output
current. If the current limit is reached, the high-side FET is turned off. Avoiding shoot-through current, the lowside FET is switched on to sink the inductor current. The high-side FET turns on again only if the current in the
low-side FET has decreased below the low-side current-limit threshold.
The output current of the device is limited by the current limit (see ELECTRICAL CHARACTERISTICS). Due to
internal propagation delay, the actual current can exceed the static current limit during that time. The dynamic
current limit can be calculated as follows:
I peak ( typ ) = I LIMF +
16
VL
× t PD
L
Submit Documentation Feedback
(4)
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
where
ILIMF is the static current limit, specified in the ELECTRICAL CHARACTERISTICS
L is the inductor value
VL is the voltage across the inductor (VIN – VOUT)
tPD is the internal propagation delay
The current limit can exceed static values, especially if the input voltage is high and very small inductances are
used. The dynamic high-side switch peak current can be calculated as follows:
(V - VOUT )× 30ns
I peak (typ ) = I LIMF + IN
L
(5)
Power Good (PG)
The TPS6214X has a built-in power-good (PG) function to indicate whether the output voltage has reached its
appropriate level or not. The PG signal can be used for start-up sequencing of multiple rails. The PG pin is an
open-drain output that requires a pullup resistor (to any voltage below 7 V). It can sink 2 mA of current and
maintain its specified logic-low level. It is high-impedance when the device is turned off due to EN, UVLO, or
thermal shutdown. TPS62140A features PG=Low in this case and can be used to actively discharge Vout (see
Figure 51). VIN must remain present for the PG pin to stay Low.
Pin-Selectable Output Voltage (DEF)
The output voltage of the TPS6214X devices can be increased by 5% above the nominal voltage by setting the
DEF pin to High (1). When DEF is Low, the device regulates to the nominal output voltage. Increasing the nominal
voltage allows adapting the power supply voltage to the variations of the application hardware. More detailed
information on voltage margining using TPS6214X can be found in SLVA489. A pull down resistor of about
400kOhm is internally connected to the pin, to ensure a proper logic level if the pin is high impedance or floating
after initially set to Low. The resistor is disconnected if the pin is set High.
Frequency Selection (FSW)
To get high power density with very small solution size, a high switching frequency allows the use of small
external components for the output filter. However switching losses increase with the switching frequency. If
efficiency is the key parameter, more than solution size, the switching frequency can be set to half (1.25 MHz
typ.) by pulling FSW to High. It is mandatory to start with FSW=Low to limit inrush current, which can be done by
connecting to VOUT or PG. Running with lower frequency a higher efficiency, but also a higher output voltage
ripple, is achieved. Pull FSW to Low for high frequency operation (2.5 MHz typ.). To get low ripple and full output
current at the lower switching frequency, it's recommended to use an inductor of at least 2.2uH. The switching
frequency can be changed during operation, if needed. A pull down resistor of about 400kOhm is internally
connected to the pin, acting the same way as at the DEF Pin (see above).
Undervoltage Lockout (UVLO)
If the input voltage drops, the undervoltage lockout prevents incorrect operation of the device by switching off
both the power FETs. The undervoltage lockout threshold is set typically to 2.7 V. The device is fully operational
for voltages above the UVLO threshold and turns off if the input voltage trips the threshold. The converter starts
operation again once the input voltage exceeds the threshold by a hysteresis of typically 200 mV.
Thermal Shutdown
The junction temperature (TJ) of the device is monitored by an internal temperature sensor. If TJ exceeds 160°C
(typ), the device goes into thermal shutdown. Both the high-side and low-side power FETs are turned off and PG
goes high-impedance. When TJ decreases below the hysteresis amount, the converter resumes normal
operation, beginning with soft start. To avoid unstable conditions, a hysteresis of typically 20°C is implemented
on the thermal shutdown temperature.
(1)
Maximum allowed voltage is 7 V. Therefore it is recommended to connect it to VOUT or PG, not VIN.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
17
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
APPLICATION INFORMATION
The following information is intended to be a guideline through the individual power-supply design process.
Programming the Output Voltage
While the output voltage of the TPS62140 is adjustable, the TPS62141/2/3 are programmed to fixed output
voltages. For fixed output versions, the FB pin is pulled down internally and may be left floating. It is
recommended to connect to AGND to improve thermal resistance. The adjustable version can be programmed
for output voltages from 0.9 V to 6 V by using a resistive divider from VOUT to AGND. The voltage at the FB pin
is regulated to 800 mV. The value of the output voltage is set by the selection of the resistive divider from
Equation 6 (see Figure 4). It is recommended to choose resistor values which allow a current of at least 2 µA,
meaning the value of R2 should not exceed 400 kΩ. Lower resistor values are recommended for highest
accuracy and most-robust design. For applications requiring lowest current consumption, the use of fixed outputvoltage versions is recommended.
æV
ö
R1 = R 2 çç OUT - 1÷÷
V
è REF
ø
(6)
In case the FB pin is opened, the device clamps the output voltage at the VOS pin internally to about 7.4 V.
External Component Selection
The external components have to fulfill the needs of the application, but also the stability criteria of the devices
control loop. The TPS6214X is optimized to work within a range of external components. The LC output filters
inductance and capacitance have to be considered in conjunction, creating a double pole, responsible for the
corner frequency of the converter (see Output Filter and Loop Stabilitysection). Table 1 can be used to simplify
the output filter component selection.
Table 1. Recommended LC Output Filter Combinations (1)
4.7 µF
10 µF
22 µF
47 µF
100 µF
200 µF
√
√
√
√
(2)
√
√
√
√
√
√
400 µF
0.47 µH
1 µH
2.2 µH
√
3.3 µH
√
√
4.7 µH
(1)
(2)
The values in the table are nominal values.
This LC combination is the standard value and recommended for most applications.
spacing
TPS6214X can be run with an inductor as low as 1 µH or 2.2 µH. FSW should be set Low in this case. However,
for applications running with the low-frequency setting (FSW = High) or with low input voltages, 3.3 µH is
recommended. More detailed information on further LC combinations can be found in SLVA463.
Inductor Selection
The inductor selection is affected by several effects like inductor ripple current, output ripple voltage, PWM-toPSM transition point, and efficiency. In addition, the inductor selected must be rated for appropriate saturation
current and dc resistance (DCR). Equation 7 and Equation 8 calculate the maximum inductor current under static
load conditions.
spacing
I L(max) = I OUT (max) +
18
DI L(max)
2
Submit Documentation Feedback
(7)
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
DI L(max) = VOUT
V
æ
ç 1 - OUT
V
ç
IN (max)
×ç
L(min) × f SW
ç
ç
è
ö
÷
÷
÷
÷
÷
ø
(8)
where
IL(max) is the maximum inductor current
ΔIL is the peak-to-peak inductor ripple current
L(min) is the minimum effective inductor value
fSW is the actual PWM switching frequency
spacing
Calculating the maximum inductor current using the actual operating conditions gives the minimum required
inductor saturation current. It is recommended to add a margin of about 20%. A larger inductor value is also
useful to get lower ripple current, but increases the transient response time and size as well. The following
inductors have been used with the TPS6214X and are recommended for use:
Table 2. List of Inductors
(1)
Type
Inductance [µH]
Current [A] (1)
Dimensions [L x B x H]
mm
MANUFACTURER
XFL4020-222ME_
2.2 µH, ±20%
3.5
4 x 4 x 2.1
Coilcraft
XFL4020-332ME_
3.3 µH, ±20%
2.9
4 x 4 x 2.1
Coilcraft
IHLP1212BZ-11
2.2 µH, ±20%
3.0
3 x 3.6 x 2
Vishay
IHLP1616AB-11
2.2 µH, ±20%
2.75
4.05 x 4.45 x 1.2
Vishay
DEM4518C 1235AS-H-3R3M
3.3 µH, ±20%
2.5
4.5 x 4.7 x 1.9
Toko
Lower of IRMS at 40°C rise or ISAT at 30% drop.
spacing
The inductor value also determines the load current at which the power-save mode is entered:
I load ( PSM ) =
1
DI L
2
(9)
Using Equation 8, this current level can be adjusted by changing the inductor value.
Capacitor Selection
Output Capacitor
The recommended value for the output capacitor is 22 µF. The architecture of the TPS6214X allows the use of
tiny ceramic output capacitors with low equivalent series resistance (ESR). These capacitors provide low outputvoltage ripple and are recommended. To keep its low resistance up to high frequencies and to get narrow
capacitance variation with temperature, it is recommended to use X7R or X5R dielectric. Using a higher value
can have some advantages, like smaller voltage ripple and a tighter dc output accuracy in power-save mode (see
SLVA463).
Note: In power-save mode, the output voltage ripple depends on the output capacitance, its ESR and the peak
inductor current. Using ceramic capacitors provides small ESR and low ripple.
Input Capacitor
For most applications, 10 µF is sufficient and is recommended, though a larger value reduces input-current ripple
further. The input capacitor buffers the input voltage for transient events and also decouples the converter from
the supply. A low-ESR multilayer ceramic capacitor is recommended for best filtering and should be placed
between PVIN and PGND as close as possible to those pins. Even though AVIN and PVIN must be supplied
from the same input source, it is recommended to place a capacitance of 0.1 uF from AVIN to AGND, to avoid
potential noise coupling.
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
19
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
Soft-Start Capacitor
A capacitance connected between the SS/TR pin and AGND allows a user-programmable start-up slope of the
output voltage. A constant-current source provides 2.5 µA to charge the external capacitance. The capacitor
required for a given soft-start ramp time for the output voltage is given by:
C SS = t SS ×
2.5mA
1.25V
[F ]
(10)
where
CSS is the capacitance (F) required at the SS/TR pin and
tSS is the desired soft-start ramp time (s).
spacing
NOTE
DC bias effect: High-capacitance ceramic capacitors have a dc bias effect, which has a
strong influence on the final effective capacitance. Therefore, the right capacitor value
must be chosen carefully. Package size and voltage rating in combination with dielectric
material are responsible for differences between the rated capacitor value and the
effective capacitance.
spacing
Tracking Function
If a tracking function is desired, the SS/TR pin can be used for this purpose by connecting it to an external
tracking voltage. The output voltage tracks that voltage. If the tracking voltage is between 50 mV and 1.2 V, the
FB pin tracks the SS/TR pin voltage as described in Equation 11 and shown in Figure 39.
spacing
VFB » 0.64 × VSS / TR
(11)
VSS/TR
[V]
1.2
0.8
0.4
0.2
0.4
0.6
0.8
VFB [V]
Figure 39. Voltage Tracking Relationship
Once the SS/TR pin voltage reaches about 1.2V, the internal voltage is clamped to the internal feedback voltage
and device goes to normal regulation. This works for rising and falling tracking voltages with the same behavior,
as long as the input voltage is inside the recommended operating conditions. For decreasing SS/TR pin voltage,
the device doesn't sink current from the output. So, the resulting decrease of the output voltage may be slower
than the SS/TR pin voltage if the load is light. When driving the SS/TR pin with an external voltage, do not
exceed the voltage rating of the SS/TR pin which is VIN+0.3V.
If the input voltage drops into undervoltage lockout or even down to zero, the output voltage goes to zero,
independent of the tracking voltage. Figure 40 shows how to connect devices to get ratiometric and simultaneous
sequencing by using the tracking function.
spacing
20
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
VOUT1
PVIN
SW
AVIN
VOS
EN
PG
TPS62140
SS/TR
FB
DEF
AGND
FSW
PGND
PVIN
SW
AVIN
VOS
VOUT2
R1
EN
PG
TPS62140
SS/TR
R2
FB
DEF
AGND
FSW
PGND
Figure 40. Sequence for Ratiometric and Simultaneous Startup
The resistive divider of R1 and R2 can be used to change the ramp rate of VOUT2 faster, slower, or the same as
VOUT1.
A sequential start-up is achieved by connecting the PG pin of VOUT1 to the EN pin of VOUT2. A ratiometric
start-up sequence happens if both supplies are sharing the same soft-start capacitor. Equation 10 calculates the
soft-start time, though the SS/TR current must be doubled. Details about these and other tracking and
sequencing circuits are found in SLVA470.
Note: If the voltage at the FB pin is below its typical value of 0.8 V, the output voltage accuracy may have a
wider tolerance than specified.
Output Filter and Loop Stability
The devices of the TPS6214X family are internally compensated to be stable with L-C filter combinations
corresponding to a corner frequency to be calculated with Equation 12:
f LC =
1
2p L × C
(12)
Proven nominal values for inductance and ceramic capacitance are given in Table 1 and are recommended for
use. Different values may work, but care must be taken on the loop stability, which is affected. More information
including a detailed L-C stability matrix can be found in SLVA463.
The TPS6214X devices, both fixed and adjustable versions, include an internal 25 pF feed-forward capacitor,
connected between the VOS and FB pins. This capacitor impacts the frequency behavior and sets a pole and
zero in the control loop with the resistors of the feedback divider, per equations Equation 13 and Equation 14:
spacing
f zero =
1
2p × R1 × 25 pF
Copyright © 2011–2013, Texas Instruments Incorporated
(13)
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
21
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
spacing
f pole =
1
2p × 25 pF
æ 1
1 ö
÷÷
× çç
+
è R1 R 2 ø
(14)
spacing
Though the TPS6214X devices are stable without the pole and zero being in a particular location, adjusting their
location to the specific needs of the application can provide better performance in power-save mode and/or
improved transient response. An external feed-forward capacitor can also be added. A more detailed discussion
on the optimization for stability vs transient response can be found in SLVA289 and SLVA466.
Layout Considerations
A proper layout is critical for the operation of a switched-mode power supply, even more at high switching
frequencies. Therefore, the PCB layout of the TPS6214X demands careful attention to ensure operation and to
get the performance specified. A poor layout can lead to issues like poor regulation (both line and load), stability
and accuracy weaknesses, increased EMI radiation, and noise sensitivity.
See Figure 41 for the recommended layout of the TPS6214X, which is designed for common external ground
connections. Therefore both AGND and PGND pins are directly connected to the Exposed Thermal Pad. On the
PCB, the direct common ground connection of AGND and PGND to the Exposed Thermal Pad and the system
ground (ground plane) is mandatory. Also connect the VOS pin in the shortest way to VOUT at the output
capacitor.
Provide low inductive and resistive paths for loops with high di/dt. Therefore, paths conducting the switched load
current should be as short and wide as possible. Provide low capacitive paths (with respect to all other nodes) for
wires with high dv/dt. Therefore, the input and output capacitance should be placed as close as possible to the
IC pins and parallel wiring over long distances as well as narrow traces should be avoided. Loops which conduct
an alternating current should outline an area as small as possible, as this area is proportional to the energy
radiated.
Sensitive nodes like FB and VOS need to be connected with short wires and not nearby high dv/dt signals (that
is, SW). As they carry information about the output voltage, they should be connected as close as possible to the
actual output voltage (at the output capacitor). The capacitor on the SS/TR pin and on AVIN as well as the FB
resistors, R1 and R2, should be kept close to the IC and connect directly to those pins and the system ground
plane.
The Exposed Thermal Pad must be soldered to the circuit board for mechanical reliability and to achieve
appropriate power dissipation.
The recommended layout is implemented on the EVM and shown in its Users Guide, SLVU437. Additionally, the
EVM Gerber data are available for download here, SLVC394.
22
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
GND
R2
8
C
PVIN
AVIN
7
R1
6
5
9
4
10
3
11
2
12
1
13
CIN
14
15
PG
16
EN
L1
to GND
plane
VOUT
COUT
to
AGND
GND
Figure 41. Layout Example
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the powerdissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
• Improving the power dissipation capability of the PCB design
• Improving the thermal coupling of the component to the PCB by soldering the exposed thermal pad
• Introducing airflow in the system
For more details on how to use the thermal parameters, see the application notes: Thermal Characteristics
Application Note (SZZA017), and (SPRA953).
The TPS6214X is designed for a maximum operating junction temperature (TJ) of 125°C. Therefore, the
maximum output power is limited by the power losses that can be dissipated over the actual thermal resistance,
given by the package and the surrounding PCB structures. If the thermal resistance of the package is given, the
size of the surrounding copper area and a proper thermal connection of the IC can reduce the thermal
resistance. To get improved thermal behavior, it is recommended to use top layer metal to connect the device
with wide and thick metal lines. Internal ground layers can connect to vias directly under the IC for improved
thermal performance.
If short-circuit or overload conditions are present, the device is protected by limiting internal power dissipation.
Experimental data, taken from the TPS62140 EVM, shows the maximum ambient temperature (without additional
cooling like airflow or heat sink), that can be allowed to limit the junction temperature to at most 125°C (see
Figure 37).
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
23
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
Application Example As Power LED Supply
The TPS62140 can be used as a power supply for power LEDs. The FB pin can be easily set down to lower
values than nominal by using the SS/TR pin. With that, the voltage drop on the sense resistor is low to avoid
excessive power loss. Because this pin provides 2.5 µA, the feedback pin voltage can be adjusted by an external
resistor per Equation 15. This drop, proportional to the LED current, is used to regulate the output voltage (anode
voltage) to a proper level to drive the LED. Both analog and PWM dimming are supported with the TPS62140.
Figure 42 shows an application circuit, tested with analog dimming:
spacing
(4 .. 17) V
2.2 µH
PVIN
SW
AVIN
VOS
PG
EN
10uF
ADIM
22uF
TPS62140
FB
SS/TR
187k
DEF
AGND
FSW
PGND
0.15R
Figure 42. Single Power LED Supply
spacing
The resistor at SS/TR sets the FB voltage to a level of about 300 mV and is calculated from Equation 15.
spacing
V FB = 0.64 × 2.5mA × R SS / TR
(15)
spacing
The device now supplies a constant current, set by the resistor at the FB pin, by regulating the output voltage
accordingly. The minimum input voltage must be rated according to the forward voltage needed by the LED
used. More information is available in the application note SLVA451.
spacing
Typical Applications
spacing
spacing
(5 .. 17)V
5V / 2A
2.2 µH
10uF
PVIN
SW
AVIN
VOS
100k
PG
EN
22uF
TPS62143
SS/TR
3.3nF
FB
DEF
AGND
FSW
PGND
Figure 43. 5-V/2-A Power Supply
spacing
spacing
spacing
spacing
24
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
spacing
spacing
spacing
(3.3 .. 17)V
3.3V / 2A
2.2 µH
10uF
PVIN
SW
AVIN
VOS
100k
PG
EN
22uF
TPS62142
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
Figure 44. 3.3-V/2-A Power Supply
spacing
spacing
spacing
(3 .. 17)V
2.5V / 2A
2.2 µH
PVIN
SW
AVIN
VOS
100k
PG
EN
10uF
390k
22uF
TPS62140
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
180k
Figure 45. 2.5-V/2-A Power Supply
spacing
spacing
spacing
(3 .. 17)V
1.8V / 2A
2.2 µH
10uF
PVIN
SW
AVIN
VOS
PG
EN
100k
22uF
TPS62141
SS/TR
3.3nF
FB
DEF
AGND
FSW
PGND
Figure 46. 1.8-V/2-A Power Supply
spacing
spacing
spacing
spacing
spacing
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
25
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
spacing
spacing
spacing
(3 .. 17)V
1.5V / 2A
2.2 µH
PVIN
SW
AVIN
VOS
100k
PG
EN
10uF
130k
22uF
TPS62140
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
150k
Figure 47. 1.5-V/2-A Power Supply
spacing
spacing
spacing
(3 .. 17)V
1.2V / 2A
2.2 µH
PVIN
SW
AVIN
VOS
100k
PG
EN
10uF
75k
22uF
TPS62140
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
150k
Figure 48. 1.2-V/2-A Power Supply
spacing
spacing
spacing
1V / 2A
2.2 µH
PVIN
SW
AVIN
VOS
100k
PG
EN
10uF
51k
22uF
TPS62140
SS/TR
3.3nF
FB
DEF
AGND
FSW
PGND
200k
Figure 49. 1-V/2-A Power Supply
26
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
www.ti.com
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
Application Example As Inverting Power Supply
spacing
The TPS62140 can be used as inverting power supply by rearranging external circuitry as shown in Figure 50.
As the former GND node now represents a voltage level below system ground, the voltage difference between
VIN and VOUT has to be limited for operation to the maximum supply voltage of 17V (see Equation 16).
spacing
V IN + VOUT £ V IN max
(16)
spacing
10uF
2.2µH
(3 .. 13.7)V
PVIN
SW
AVIN
VOS
10uF
PG
EN
1.21M
TPS62140
SS/TR
22uF
FB
3.3nF
DEF
AGND
FSW
PGND
383k
-3.3V
Figure 50. –3.3V Inverting Power Supply
spacing
The transfer function of the inverting power supply configuration differs from the buck mode transfer function,
incorporating a Right Half Plane Zero additionally. The loop stability has to be adapted and an output
capacitance of at least 22µF is recommended. A detailed design example is given in SLVA469.
spacing
Active Output Discharge
spacing
The TPS62140A pulls the PG pin Low, when the device is shut down by EN, UVLO or thermal shutdown.
Connecting PG to Vout through a resistor can be used to discharge Vout in those cases (see Figure 51). The
discharge rate can be adjusted by R3, which is also used to pull up the PG pin in normal operation. For reliability,
keep the maximum current into the PG pin less than 10mA.
spacing
(3 .. 17)V
1 / 2.2 µH
PVIN
Vout / 2A
SW
TPS62140A
AVIN
10uF
3.3nF
VOS
EN
PG
SS/TR
FB
DEF
AGND
FSW
PGND
R3
R1
22uF
R2
Figure 51. Discharge Vout through PG pin
Copyright © 2011–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
27
TPS62140, TPS62140A
TPS62141, TPS62142, TPS62143
SLVSAJ0B – NOVEMBER 2011 – REVISED JUNE 2013
www.ti.com
REVISION HISTORY
Changes from Original (November 2011) to Revision A
Page
•
Added values to the Initial output voltage accuracy for TA = –10°C to 85°C ........................................................................ 3
•
Changed the description of the AGND pin, and added Note 3. ........................................................................................... 4
•
Added text to the Power-Save Mode Operation section following Equation 1 ................................................................... 15
•
Changed the Layout Considerations section ...................................................................................................................... 22
•
Changed Figure 41 ............................................................................................................................................................. 23
Changes from Revision A (October 2012) to Revision B
Page
•
Added new device version TPS62140A to the data sheet ................................................................................................... 1
•
Added device TPS62140A to Ordering Info table ................................................................................................................. 2
•
Added text to Power Good section regarding the TPS62140A function ............................................................................. 17
•
Added pin option to the footnote for Pin-Selectable Output (DEF) section. ....................................................................... 17
•
Added text to Frequency Selection (FSW) section regarding pin control. .......................................................................... 17
•
Added text to Tracking Function section for clarification. ................................................................................................... 20
•
Added application example with regard to new version TPS62140A. ................................................................................ 27
28
Submit Documentation Feedback
Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: TPS62140 TPS62140A TPS62141 TPS62142 TPS62143
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jul-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
TPS62140ARGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
PA7I
TPS62140ARGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
PA7I
TPS62140RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QTZ
TPS62140RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QTZ
TPS62141RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWA
TPS62141RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWA
TPS62142RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWB
TPS62142RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWB
TPS62143RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWC
TPS62143RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QWC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jul-2013
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS62140ARGTR
QFN
RGT
16
TPS62140ARGTT
QFN
RGT
TPS62140RGTR
QFN
RGT
TPS62140RGTT
QFN
TPS62141RGTR
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62141RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62142RGTR
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62142RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62143RGTR
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62143RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jul-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS62140ARGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62140ARGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62140RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62140RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62141RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62141RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62142RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62142RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62143RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62143RGTT
QFN
RGT
16
250
552.0
185.0
36.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated