Inductors (Coils) for Power Lines Data Sheet 1 LQM2MPN_GH Series 2016/0806 (mm/inch) General Multilayer Thickness 1.0 mm Low Rdc Bias max. Reflow RoHS OK c Packaging 0.5±0.2 0.9±0.1 c Dimensions Code Packaging Minimum Quantity L ø180mm Embossed taping 3000 1.6±0.2 2.0±0.3 (in mm) c Rated Value (p: packaging code) Part Number Inductance Inductance Rated current test frequency (Based on Inductance change) Rated current (Based on Temperature rise) DC resistance Self resonance frequency (min.) LQM2MPNR16MGHp 0.16µH ±20% 1MHz 4.8A 4.0A 0.014Ω±25% 150MHz LQM2MPNR24MGHp 0.24µH ±20% 1MHz 4.0A 3.4A 0.020Ω±25% 130MHz LQM2MPNR33MGHp 0.33µH ±20% 1MHz 3.2A 3.1A 0.024Ω±25% 90MHz LQM2MPNR47MGHp 0.47µH ±20% 1MHz 3.2A 2.5A 0.037Ω±25% 80MHz LQM2MPNR68MGHp 0.68µH ±20% 1MHz 2.1A 1.9A 0.060Ω±25% 60MHz LQM2MPN1R0MGHp 1.0µH ±20% 1MHz 1.6A 1.9A 0.064Ω±25% 60MHz LQM2MPN1R5MGHp 1.5µH ±20% 1MHz 1.5A 1.5A 0.104Ω±25% 50MHz LQM2MPN2R2MGHp 2.2µH ±20% 1MHz 1.0A 1.0A 0.210Ω±25% 40MHz Class of magnetic shield: Magnetic shield of ferrite Operating temperature range: -40∼85℃ Only for reflow soldering. c Notice (Rating) When applied Rated current to the Products, Inductance will be within ±30% of initial Inductance value. When applied Rated current to the Products, self temperature rise shall be limited to 40°C max. Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.7.8 http://www.murata.com/ Inductors (Coils) for Power Lines Data Sheet 2 Continued from the preceding page. c Inductance-Frequency characteristics (Typ.) c Inductance-Current characteristics (Typ.) 10 10 2.2μH Inductance (μH) 2.2μH L (μH) 1.5μH 1.0μH 1 0.68μH 0.47μH 0.1 0.1 1.5μH 1.0μH 1 0.68μH 0.47μH 0.33μH 0.33μH 0.24μH 0.24μH 0.16μH 0.16μH 0.1 1 10 Frequency (MHz) 100 1000 1 10 100 Current (mA) 1000 10000 c Temperature rise characteristics (Typ.) 50 45 40 0.24μH Temperature (°C) 35 1.0μH 1.5μH 30 25 0.16μH 0.33μH 0.68μH 0.47μH 20 2.2μH 15 10 5 0 0 500 1000 1500 2000 2500 Current (mA) 3000 3500 4000 4500 c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.7.8 http://www.murata.com/