BB OPA2227U/2K5E4

OPA227
OPA2227
OPA4227
OPA
4
227
OPA
227
OPA
2
227
OPA
42
OPA2
27
OPA228
27
OPA2
227
OPA2228
OPA4228
SBOS110A – MAY 1998 – REVISED JANUARY 2005
High Precision, Low Noise
OPERATIONAL AMPLIFIERS
FEATURES
DESCRIPTION
● LOW NOISE: 3nV/√Hz
● WIDE BANDWIDTH:
OPA227: 8MHz, 2.3V/µs
OPA228: 33MHz, 10V/µs
The OPA227 and OPA228 series op amps combine low
noise and wide bandwidth with high precision to make them
the ideal choice for applications requiring both ac and precision dc performance.
● SETTLING TIME: 5µs
(significant improvement over OP-27)
●
●
●
●
●
●
The OPA227 is unity-gain stable and features high slew rate
(2.3V/µs) and wide bandwidth (8MHz). The OPA228 is optimized for closed-loop gains of 5 or greater, and offers higher
speed with a slew rate of 10V/µs and a bandwidth of 33MHz.
HIGH CMRR: 138dB
HIGH OPEN-LOOP GAIN: 160dB
LOW INPUT BIAS CURRENT: 10nA max
LOW OFFSET VOLTAGE: 75µV max
WIDE SUPPLY RANGE: ±2.5V to ±18V
OPA227 REPLACES OP-27, LT1007, MAX427
The OPA227 and OPA228 series op amps are ideal for
professional audio equipment. In addition, low quiescent
current and low cost make them ideal for portable applications requiring high precision.
● OPA228 REPLACES OP-37, LT1037, MAX437
The OPA227 and OPA228 series op amps are pin-for-pin
replacements for the industry standard OP-27 and OP-37
with substantial improvements across the board. The dual
and quad versions are available for space savings and perchannel cost reduction.
● SINGLE, DUAL, AND QUAD VERSIONS
APPLICATIONS
●
●
●
●
●
●
●
DATA ACQUISITION
TELECOM EQUIPMENT
GEOPHYSICAL ANALYSIS
VIBRATION ANALYSIS
SPECTRAL ANALYSIS
PROFESSIONAL AUDIO EQUIPMENT
ACTIVE FILTERS
The OPA227, OPA228, OPA2227, and OPA2228 are
available in DIP-8 and SO-8 packages. The OPA4227 and
OPA4228 are available in DIP-14 and SO-14 packages
with standard pin configurations. Operation is specified
from –40°C to +85°C.
OPA4227, OPA4228
● POWER SUPPLY CONTROL
SPICE model available for OPA227 at www.ti.com
Out A
1
OPA227, OPA228
Out A
1
Trim
1
8
Trim
–In A
2
–In
2
7
V+
+In A
3
+In
3
6
Output
V–
4
V–
4
5
NC
8
A
B
Out D
–In A
2
13
–In D
+In A
3
12
+In D
V+
4
11
V–
+In B
5
10
+In C
A
OPA2227, OPA2228
14
D
V+
7
Out B
6
–In B
5
+In B
B
C
–In B
6
9
–In C
Out B
7
8
Out C
DIP-14, SO-14
DIP-8, SO-8
DIP-8, SO-8
NC = Not Connected
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 1998-2005, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
SPECIFICATIONS: VS = ±5V to ±15V
OPA227 Series
At TA = +25°C, and RL = 10kΩ, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
OPA227PA, UA
OPA2227PA, UA
OPA4227PA, UA
OPA227P, U
OPA2227P, U
PARAMETER
CONDITION
OFFSET VOLTAGE
Input Offset Voltage
VOS
OTA = –40°C to +85°Cver Temperature
vs Temperature
dVOS/dT
vs Power Supply
PSRR
TA = –40°C to +85°C
vs Time
Channel Separation (dual, quad)
INPUT BIAS CURRENT
Input Bias Current
TA = –40°C to +85°C
Input Offset Current
TA = –40°C to +85°C
MIN
TYP
±5
±0.1
VS = ±2.5V to ±18V
±0.5
±2.5
IOS
±2.5
Input Voltage Noise Density, f = 10Hz en
f = 100Hz
f = 1kHz
Current Noise Density, f = 1kHz
in
90
15
3.5
3
3
0.4
NOISE
Input Voltage Noise, f = 0.1Hz to 10Hz
VCM
CMRR
INPUT IMPEDANCE
Differential
Common-Mode
AOL
FREQUENCY RESPONSE
Gain Bandwidth Product
GBW
Slew Rate
SR
Settling Time: 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise THD+N
OUTPUT
Voltage Output
TA = –40°C to +85°C
VO = (V–)+2V to (V+)–2V, RL = 10kΩ
132
132
132
132
10kΩ
10kΩ
600Ω
600Ω
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SO-8 Surface Mount
DIP-8
DIP-14
SO-14 Surface Mount
±5
±2.5
VS
IQ
✻
IO = 0
IO = 0
±10
✻
±10
✻
±10
±10
✻
✻
✻
✻
✻
✻
✻
160
160
θJA
150
100
80
100
±200
✻
✻
µV
µV
µV/°C
µV/V
µV/V
µV/mo
µV/V
dB
✻
✻
✻
✻
nA
nA
nA
nA
±200
±2
nVp-p
nVrms
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
✻
✻
V
dB
dB
✻
✻
Ω || pF
Ω || pF
✻
dB
dB
dB
dB
✻
✻
✻
✻
✻
✻
✻
(V+)–2
(V+)–2
(V+)–3.5
(V+)–3.5
–40
–55
–65
UNITS
✻
✻
✻
✻
✻
✻
(V+)–2
±3.7
MAX
✻
✻
✻
✻
✻
✻
✻
±45
See Typical Curve
ISC
CLOAD
POWER SUPPLY
Specified Voltage Range
Operating Voltage Range
Quiescent Current (per amplifier)
TA = –40°C to +85°C
±0.3
±2
±2
138
(V–)+2
(V–)+2
(V–)+3.5
(V–)+3.5
TYP
±10
8
2.3
5
5.6
1.3
0.00005
G = 1, 10V Step, CL = 100pF
G = 1, 10V Step, CL = 100pF
VIN • G = VS
f = 1kHz, G = 1, VO = 3.5Vrms
RL =
RL =
RL =
RL =
±75
±100
±0.6
107 || 12
109 || 3
VO = (V–)+3.5V to (V+)–3.5V, RL = 600Ω
TA = –40°C to +85°C
TA = –40°C to +85°C
Short-Circuit Current
Capacitive Load Drive
(V–)+2
120
120
VCM = (V–)+2V to (V+)–2V
VCM = (V–)+2V to (V+)–2V
OPEN-LOOP GAIN
Open-Loop Voltage Gain
TA = –40°C to +85°C
MIN
0.2
0.2
110
dc
f = 1kHz, RL = 5kΩ
IB
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection
TA = –40°C to +85°C
MAX
MHz
V/µs
µs
µs
µs
%
✻
✻
✻
✻
V
V
V
V
mA
✻
✻
✻
✻
V
V
mA
mA
✻
✻
✻
°C
°C
°C
✻
✻
±15
±18
±3.8
±4.2
✻
✻
+85
+125
+150
✻
✻
✻
✻
✻
✻
✻
✻
°C/W
°C/W
°C/W
°C/W
✻ Specifications same as OPA227P, U.
2
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
SPECIFICATIONS: VS = ±5V to ±15V
OPA228 Series
At TA = +25°C, and RL = 10kΩ, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
OPA228PA, UA
OPA2228PA, UA
OPA4228PA, UA
OPA228P, U
OPA2228P, U
PARAMETER
CONDITION
OFFSET VOLTAGE
Input Offset Voltage
VOS
OTA = –40°C to +85°Cver Temperature
vs Temperature
dVOS/dT
vs Power Supply
PSRR
TA = –40°C to +85°C
vs Time
Channel Separation (dual, quad)
INPUT BIAS CURRENT
Input Bias Current
TA = –40°C to +85°C
Input Offset Current
TA = –40°C to +85°C
MIN
TYP
±5
±0.1
VS = ±2.5V to ±18V
±0.5
±2.5
IOS
±2.5
Input Voltage Noise Density, f = 10Hz en
f = 100Hz
f = 1kHz
Current Noise Density, f = 1kHz
in
90
15
3.5
3
3
0.4
NOISE
Input Voltage Noise, f = 0.1Hz to 10Hz
VCM
CMRR
INPUT IMPEDANCE
Differential
Common-Mode
AOL
FREQUENCY RESPONSE
Minimum Closed-Loop Gain
Gain Bandwidth Product
GBW
Slew Rate
SR
Settling Time: 0.1%
0.01%
Overload Recovery Time
Total Harmonic Distortion + Noise THD+N
OUTPUT
Voltage Output
TA = –40°C to +85°C
VO = (V–)+2V to (V+)–2V, RL = 10kΩ
132
132
132
132
10kΩ
10kΩ
600Ω
600Ω
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
Thermal Resistance
SO-8 Surface Mount
DIP-8
DIP-14
SO-14 Surface Mount
±5
±2.5
VS
IQ
✻
IO = 0
IO = 0
±10
✻
±10
✻
±10
±10
✻
✻
✻
✻
✻
✻
✻
160
160
θJA
150
100
80
100
±200
✻
✻
µV
µV
µV/°C
µV/V
µV/V
µV/mo
µV/V
dB
✻
✻
✻
✻
nA
nA
nA
nA
±200
±2
nVp-p
nVrms
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
✻
✻
V
dB
dB
✻
✻
Ω || pF
Ω || pF
✻
dB
dB
dB
dB
✻
✻
✻
✻
✻
✻
✻
✻
(V+)–2
(V+)–2
(V+)–3.5
(V+)–3.5
–40
–55
–65
UNITS
✻
✻
✻
✻
✻
✻
(V+)–2
±3.7
MAX
✻
✻
✻
✻
✻
✻
✻
±45
See Typical Curve
ISC
CLOAD
POWER SUPPLY
Specified Voltage Range
Operating Voltage Range
Quiescent Current (per amplifier)
TA = –40°C to +85°C
±0.3
±2
±2
138
(V–)+2
(V–)+2
(V–)+3.5
(V–)+3.5
TYP
±10
5
33
11
1.5
2
0.6
0.00005
G = 5, 10V Step, CL = 100pF, CF =12pF
G = 5, 10V Step, CL = 100pF, CF =12pF
VIN • G = VS
f = 1kHz, G = 5, VO = 3.5Vrms
RL =
RL =
RL =
RL =
±75
±100
±0.6
107 || 12
109 || 3
VO = (V–)+3.5V to (V+)–3.5V, RL = 600Ω
TA = –40°C to +85°C
TA = –40°C to +85°C
Short-Circuit Current
Capacitive Load Drive
(V–)+2
120
120
VCM = (V–)+2V to (V+)–2V
VCM = (V–)+2V to (V+)–2V
OPEN-LOOP GAIN
Open-Loop Voltage Gain
TA = –40°C to +85°C
MIN
0.2
0.2
110
dc
f = 1kHz, RL = 5kΩ
IB
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection
TA = –40°C to +85°C
MAX
V/V
MHz
V/µs
µs
µs
µs
%
✻
✻
✻
✻
V
V
V
V
mA
✻
✻
✻
✻
V
V
mA
mA
✻
✻
✻
°C
°C
°C
✻
✻
±15
±18
±3.8
±4.2
✻
✻
+85
+125
+150
✻
✻
✻
✻
✻
✻
✻
✻
°C/W
°C/W
°C/W
°C/W
✻ Specifications same as OPA228P, U.
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
www.ti.com
3
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage .................................................................................. ±18V
Signal Input Terminals, Voltage ........................ (V–) –0.7V to (V+) +0.7V
Current ....................................................... 20mA
Output Short-Circuit(2) .............................................................. Continuous
Operating Temperature .................................................. –55°C to +125°C
Storage Temperature ..................................................... –65°C to +150°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s) ................................................. 300°C
NOTE: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability. (2) Short-circuit to ground, one amplifier per package.
PACKAGE/ORDERING INFORMATION
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
For the most current package and ordering information, see
the Package Option Addendum located at the end of this
datasheet, or refer to our web site at www.ti.com.
4
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
TYPICAL PERFORMANCE CURVES
At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted.
OPEN-LOOP GAIN/PHASE vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
G
AOL (dB)
120
100
φ
80
–20
160
–40
140
–60
120
–80
100
–100
60
–120
0
OPA228
–20
–40
G
–60
–80
φ
80
–100
60
–120
–140
40
–140
40
20
–160
20
–160
0
–180
0
–180
–20
0.01 0.10
1
10
100
1k
–20
0.01 0.10
–200
10k 100k 1M 10M 100M
1
10
100
1k
–200
10k 100k 1M 10M 100M
Frequency (Hz)
Frequency (Hz)
POWER SUPPLY AND COMMON-MODE
REJECTION RATIO vs FREQUENCY
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
140
100k
120
Voltage Noise (nV/√Hz)
Current Noise (fA/√Hz)
PSRR, CMRR (dB)
+CMRR
100
+PSRR
80
60
–PSRR
40
-20
–0
Current Noise
1k
100
10
Voltage Noise
1
0.1
1
10
100
1k
10k
100k
1M
0.1
1
10
100
1k
10k
Frequency (Hz)
Frequency (Hz)
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
0.01
0.01
OPA227
VOUT = 3.5Vrms
THD+Noise (%)
VOUT = 3.5Vrms
THD+Noise (%)
10k
0.001
0.0001
G = 1, RL = 10kΩ
0.00001
OPA228
0.001
0.0001
G = 1, RL = 10kΩ
0.00001
20
100
1k
10k
20k
20
Frequency (Hz)
1k
10k
50k
Frequency (Hz)
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
100
www.ti.com
5
Phase (°)
140
180
AOL (dB)
OPA227
160
0
Phase (°)
180
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, RL =10kΩ, and VS = ±15V, unless otherwise noted.
INPUT NOISE VOLTAGE vs TIME
CHANNEL SEPARATION vs FREQUENCY
50nV/div
Channel Separation (dB)
140
120
100
80
Dual and quad devices. G = 1, all channels.
Quad measured Channel A to D, or B to C;
other combinations yield similiar or improved
rejection.
60
40
10
1s/div
100
1k
10k
100k
1M
Frequency (Hz)
VOLTAGE NOISE DISTRIBUTION (10Hz)
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
24
17.5
Typical distribution
of packaged units.
Percent of Amplifiers (%)
Percent of Units (%)
15.0
16
8
12.5
10.0
5.5
5.0
2.5
0
0
3.16 3.25 3.34 3.43
3.51 3.60
–150
–135
–120
–105
–90
–75
–60
–45
–30
–15
0
15
30
45
60
75
90
105
120
135
150
0
3.69 3.78
Noise (nV/√Hz)
Offset Voltage (µV)
OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION
WARM-UP OFFSET VOLTAGE DRIFT
12
10
8
Offset Voltage Change (µV)
Percent of Amplifiers (%)
Typical distribution
of packaged units.
8
4
6
4
2
0
–2
–4
–6
–8
0
–10
0
0.5
1.0
0
1.5
100
150
200
250
300
Time from Power Supply Turn-On (s)
Offset Voltage Drift (µV)/°C
6
50
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted.
AOL, CMRR, PSRR vs TEMPERATURE
AOL, CMRR, PSRR vs TEMPERATURE
160
160
AOL
AOL, CMRR, PSRR (dB)
AOL, CMRR, PSRR (dB)
CMRR
140
130
PSRR
120
110
100
90
80
OPA227
70
60
–75
–50
AOL
150
150
CMRR
140
130
PSRR
120
110
100
90
80
OPA228
70
–25
0
25
50
75
100
60
–75
125
–50
–25
0
Short-Circuit Current (mA)
Input Bias Current (nA)
75
100
125
60
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–40 –20
0
20
40
60
80
50
40
30
20
10
0
–75
100 120 140
–ISC
+ISC
–50
–25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
QUIESCENT CURRENT vs TEMPERATURE
3.8
±18V
±15V
±12V
±10V
4.5
4.0
±5V
±2.5V
3.5
3.0
Quiescent Current (mA)
5.0
Quiescent Current (mA)
50
SHORT-CIRCUIT CURRENT vs TEMPERATURE
INPUT BIAS CURRENT vs TEMPERATURE
2.0
–2.0
–60
25
Temperature (°C)
Temperature (°C)
3.6
3.4
3.2
3.0
2.8
2.5
–60 –40
–20
0
20
40
60
80
0
100 120 140
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
2
4
6
8
10
12
14
16
18
20
Supply Voltage (±V)
Temperature (°C)
www.ti.com
7
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted.
SLEW RATE vs TEMPERATURE
SLEW RATE vs TEMPERATURE
3.0
12
OPA227
OPA228
10
Positive Slew Rate
Negative Slew Rate
Slew Rate (µV/V)
Slew Rate (µV/V)
2.5
2.0
1.5
1.0
8
6
4
RLOAD = 2kΩ
CLOAD = 100pF
0.5
0
0
–75
–50
–25
0
25
50
75
100
125
–75
–50
–25
0
75
CHANGE IN INPUT BIAS CURRENT
vs POWER SUPPLY VOLTAGE
CHANGE IN INPUT BIAS CURRENT
vs COMMON-MODE VOLTAGE
100
125
1.5
1.0
Curve shows normalized change in bias current
with respect to VCM = 0V. Typical IB may range
from –2nA to +2nA at VCM = 0V.
1.0
0.5
∆IB (nA)
0.5
0
–0.5
VS = ±15V
0
–0.5
VS = ±5V
–1.0
–1.0
–1.5
–1.5
–2.0
0
5
10
15
20
25
30
35
–15
40
–10
–5
0
5
10
15
Common-Mode Voltage (V)
Supply Voltage (V)
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
SETTLING TIME vs CLOSED-LOOP GAIN
15
100
VS = ±15V, 10V Step
CL = 1500pF
RL = 2kΩ
Output Voltage Swing (V)
Settling Time (µs)
50
Temperature (°C)
Curve shows normalized change in bias current
with respect to VS = ±10V. Typical IB may range
from –2nA to +2nA at VS = ±10V.
1.5
OPA227
0.01%
10
0.1%
OPA228
0.01%
0.1%
1
±1
±10
±100
V+
14
(V+) –1V
13
(V+) –2V
12
–40°C
125°C
85°C
25°C
11
10
–10
–55°C
85°C
–11
(V+) –3V
–55°C
125°C
–12
(V–) +3V
–40°C
25°C
–13
(V–) +2V
–14
(V–) +1V
–15
V–
0
10
20
30
40
50
60
Output Current (mA)
Gain (V/V)
8
25
Temperature (°C)
2.0
∆IB (nA)
RLOAD = 2kΩ
CLOAD = 100pF
2
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted.
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
30
70
VS = ±15V
OPA227
OPA227
60
Gain = +10
50
20
Overshoot (%)
Output Voltage (Vp-p)
25
15
VS = ±5V
10
40
30
20
5
0
Gain = –10
Gain = –1
Gain = +1
10
0
1k
10k
100k
1M
10M
1
10
100
1k
10k
Frequency (Hz)
Load Capacitance (pF)
LARGE-SIGNAL STEP RESPONSE
G = –1, CL = 1500pF
SMALL-SIGNAL STEP RESPONSE
G = +1, CL = 1000pF
OPA227
100k
2V/div
25mV/div
OPA227
400ns/div
5µs/div
SMALL-SIGNAL STEP RESPONSE
G = +1, CL = 5pF
25mV/div
OPA227
400ns/div
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
www.ti.com
9
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, RL = 10kΩ, and VS = ±15V, unless otherwise noted.
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
30
70
VS = ±15V
OPA228
OPA228
60
50
20
Overshoot (%)
Output Voltage (Vp-p)
25
15
VS = ±5V
10
G = –100
40
30
G = +100
20
G = ±10
5
10
0
0
1k
10k
100k
1M
1
10M
10
Frequency (Hz)
100
1k
10k
100k
Load Capacitance (pF)
SMALL-SIGNAL STEP RESPONSE
G = +10, CL = 1000pF, RL = 1.8kΩ
LARGE-SIGNAL STEP RESPONSE
G = –10, CL = 100pF
OPA228
5V/div
200mV/div
OPA228
500ns/div
2µs/div
SMALL-SIGNAL STEP RESPONSE
G = +10, CL = 5pF, RL = 1.8kΩ
200mV/div
OPA228
500ns/div
10
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
APPLICATIONS INFORMATION
Trim range exceeds
offset voltage specification
V+
The OPA227 and OPA228 series are precision op amps with
very low noise. The OPA227 series is unity-gain stable with
a slew rate of 2.3V/µs and 8MHz bandwidth. The OPA228
series is optimized for higher-speed applications with gains
of 5 or greater, featuring a slew rate of 10V/µs and 33MHz
bandwidth. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins. In most cases, 0.1µF capacitors are adequate.
0.1µF
20kΩ
7
2
1
8
OPA227
6
3
OPA227 and OPA228 single op amps only.
Use offset adjust pins only to
null offset voltage of op amp.
See text.
4
0.1µF
V–
OFFSET VOLTAGE AND DRIFT
The OPA227 and OPA228 series have very low offset
voltage and drift. To achieve highest dc precision, circuit
layout and mechanical conditions should be optimized.
Connections of dissimilar metals can generate thermal potentials at the op amp inputs which can degrade the offset
voltage and drift. These thermocouple effects can exceed
the inherent drift of the amplifier and ultimately degrade its
performance. The thermal potentials can be made to cancel
by assuring that they are equal at both input terminals. In
addition:
• Keep thermal mass of the connections made to the two
input terminals similar.
• Locate heat sources as far as possible from the critical
input circuitry.
• Shield op amp and input circuitry from air currents such
as those created by cooling fans.
FIGURE 1. OPA227 Offset Voltage Trim Circuit.
amp. This adjustment should not be used to compensate for
offsets created elsewhere in the system since this can
introduce additional temperature drift.
INPUT PROTECTION
Back-to-back diodes (see Figure 2) are used for input protection on the OPA227 and OPA228. Exceeding the turn-on
threshold of these diodes, as in a pulse condition, can cause
current to flow through the input protection diodes due to the
amplifier’s finite slew rate. Without external current-limiting
resistors, the input devices can be destroyed. Sources of high
input current can cause subtle damage to the amplifier.
Although the unit may still be functional, important parameters such as input offset voltage, drift, and noise may shift.
OPERATING VOLTAGE
OPA227 and OPA228 series op amps operate from ±2.5V to
±18V supplies with excellent performance. Unlike most op
amps which are specified at only one supply voltage, the
OPA227 series is specified for real-world applications; a
single set of specifications applies over the ±5V to ±15V
supply range. Specifications are assured for applications
between ±5V and ±15V power supplies. Some applications
do not require equal positive and negative output voltage
swing. Power supply voltages do not need to be equal. The
OPA227 and OPA228 series can operate with as little as 5V
between the supplies and with up to 36V between the
supplies. For example, the positive supply could be set to
25V with the negative supply at –5V or vice-versa. In
addition, key parameters are assured over the specified
temperature range, –40°C to +85°C. Parameters which vary
significantly with operating voltage or temperature are shown
in the Typical Performance Curves.
OFFSET VOLTAGE ADJUSTMENT
The OPA227 and OPA228 series are laser-trimmed for
very low offset and drift so most applications will not
require external adjustment. However, the OPA227 and
OPA228 (single versions) provide offset voltage trim connections on pins 1 and 8. Offset voltage can be adjusted by
connecting a potentiometer as shown in Figure 1. This
adjustment should be used only to null the offset of the op
RF
500Ω
–
OPA227
Input
+
FIGURE 2. Pulsed Operation.
When using the OPA227 as a unity-gain buffer (follower), the
input current should be limited to 20mA. This can be accomplished by inserting a feedback resistor or a resistor in series
with the source. Sufficient resistor size can be calculated:
RX = VS/20mA – RSOURCE
where RX is either in series with the source or inserted in
the feedback path. For example, for a 10V pulse (VS =
10V), total loop resistance must be 500Ω. If the source
impedance is large enough to sufficiently limit the current
on its own, no additional resistors are needed. The size of
any external resistors must be carefully chosen since they
will increase noise. See the Noise Performance section of
this data sheet for further information on noise calculation. Figure 2 shows an example implementing a currentlimiting feedback resistor.
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
Output
www.ti.com
11
INPUT BIAS CURRENT CANCELLATION
NOISE PERFORMANCE
The input bias current of the OPA227 and OPA228 series is
internally compensated with an equal and opposite cancellation current. The resulting input bias current is the difference
between with input bias current and the cancellation current.
The residual input bias current can be positive or negative.
Figure 4 shows total circuit noise for varying source impedances with the op amp in a unity-gain configuration (no
feedback resistor network, therefore no additional noise contributions). Two different op amps are shown with total circuit
noise calculated. The OPA227 has very low voltage noise,
making it ideal for low source impedances (less than 20kΩ).
A similar precision op amp, the OPA277, has somewhat higher
voltage noise but lower current noise. It provides excellent
noise performance at moderate source impedance (10kΩ to
100kΩ). Above 100kΩ, a FET-input op amp such as the
OPA132 (very low current noise) may provide improved
performance. The equation is shown for the calculation of the
total circuit noise. Note that en = voltage noise, in = current
noise, RS = source impedance, k = Boltzmann’s constant =
1.38 • 10–23 J/K and T is temperature in K. For more details on
calculating noise, see the insert titled “Basic Noise Calculations.”
When the bias current is cancelled in this manner, the input
bias current and input offset current are approximately equal.
A resistor added to cancel the effect of the input bias current
(as shown in Figure 3) may actually increase offset and noise
and is therefore not recommended.
Conventional Op Amp Configuration
R2
R1
Not recommended
for OPA227
RB = R2 || R1
Op Amp
VOLTAGE NOISE SPECTRAL DENSITY
vs SOURCE RESISTANCE
External Cancellation Resistor
Votlage Noise Spectral Density, E0
Typical at 1k (V/√Hz)
1.00+03
Recommended OPA227 Configuration
R2
R1
OPA227
EO
OPA227
RS
1.00E+02
OPA277
OPA277
Resistor Noise
OPA227
1.00E+01
Resistor Noise
EO2 = en2 + (in RS)2 + 4kTRS
1.00E+00
No cancellation resistor.
See text.
100
1k
10k
100k
10M
Source Resistance, RS (Ω)
FIGURE 4. Noise Performance of the OPA227 in UnityGain Buffer Configuration.
FIGURE 3. Input Bias Current Cancellation.
BASIC NOISE CALCULATIONS
Design of low noise op amp circuits requires careful
consideration of a variety of possible noise contributors:
noise from the signal source, noise generated in the op
amp, and noise from the feedback network resistors. The
total noise of the circuit is the root-sum-square combination of all noise components.
The resistive portion of the source impedance produces
thermal noise proportional to the square root of the
resistance. This function is shown plotted in Figure 4.
Since the source impedance is usually fixed, select the op
amp and the feedback resistors to minimize their contribution to the total noise.
Figure 4 shows total noise for varying source impedances with the op amp in a unity-gain configuration (no
feedback resistor network and therefore no additional
noise contributions). The operational amplifier itself contributes both a voltage noise component and a current
12
noise component. The voltage noise is commonly modeled as a time-varying component of the offset voltage.
The current noise is modeled as the time-varying component of the input bias current and reacts with the source
resistance to create a voltage component of noise. Consequently, the lowest noise op amp for a given application
depends on the source impedance. For low source impedance, current noise is negligible and voltage noise generally dominates. For high source impedance, current noise
may dominate.
Figure 5 shows both inverting and noninverting op amp
circuit configurations with gain. In circuit configurations
with gain, the feedback network resistors also contribute
noise. The current noise of the op amp reacts with the
feedback resistors to create additional noise components.
The feedback resistor values can generally be chosen to
make these noise sources negligible. The equations for
total noise are shown for both configurations.
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
Noise in Noninverting Gain Configuration
R2
Noise at the output:
2

R 
R 
2
2
E O 2 = 1 + 2  e n 2 + e12 + e 2 2 + (i n R 2 ) + e S 2 + (i n R S ) 1 + 2 
R1 
R1 


R1
EO
RS
VS
2

R 
Where eS = √4kTRS • 1 + 2  = thermal noise of RS
R1 

R 
e1 = √4kTR1 •  2 
 R1 
= thermal noise of R1
e2 = √4kTR2
= thermal noise of R2
Noise in Inverting Gain Configuration
R2
Noise at the output:
2
R1
RS
EO
VS

R2 
2
2
2
2
2
E O 2 = 1 +
 e n + e1 + e 2 + (i n R 2 ) + e S
R1 + R S 

 R2 
Where eS = √4kTRS • 
 = thermal noise of RS
 R1 + R S 
 R2 
e1 = √4kTR1 • 
 = thermal noise of R1
 R1 + R S 
e2 = √4kTR2
= thermal noise of R2
For the OPA227 and OPA228 series op amps at 1kHz, en = 3nV/√Hz and in = 0.4pA/√Hz.
FIGURE 5. Noise Calculation in Gain Configurations.
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
www.ti.com
13
R1
2MΩ
R2
2MΩ
R8
402kΩ
R11
178kΩ
R3
1kΩ
R4
9.09kΩ
C4
22nF
C6
10nF
R6
40.2kΩ
C2
1µF
C1
1µF
U1
C3
0.47µF
(OPA227)
Input from
Device
Under
Test
R7
97.6kΩ
R9
178kΩ
2
3
U2
R10
226kΩ
2
6
(OPA227)
C5
0.47µF
3
U3
6
VOUT
(OPA227)
R5
634kΩ
FIGURE 6. 0.1Hz to 10Hz Bandpass Filter Used to Test Wideband Noise of the OPA227 and OPA228 Series.
USING THE OPA228 IN LOW GAINS
The OPA228 family is intended for applications with signal
gains of 5 or greater, but it is possible to take advantage of
their high speed in lower gains. Without external compensation, the OPA228 has sufficient phase margin to maintain
stability in unity gain with purely resistive loads. However,
the addition of load capacitance can reduce the phase
margin and destabilize the op amp.
22pF
100kΩ
10Ω
2
3
OPA227
6
VOUT
Device
Under
Test
FIGURE 7. Noise Test Circuit.
Figure 6 shows the 0.1Hz 10Hz bandpass filter used to test
the noise of the OPA227 and OPA228. The filter circuit was
designed using Texas Instruments’ FilterPro software (available at www.ti.com). Figure 7 shows the configuration of
the OPA227 and OPA228 for noise testing.
14
A variety of compensation techniques have been evaluated
specifically for use with the OPA228. The recommended
configuration consists of an additional capacitor (CF) in
parallel with the feedback resistance, as shown in Figures
8 and 11. This feedback capacitor serves two purposes in
compensating the circuit. The op amp’s input capacitance
and the feedback resistors interact to cause phase shift that
can result in instability. CF compensates the input capacitance, minimizing peaking. Additionally, at high frequencies, the closed-loop gain of the amplifier is strongly
influenced by the ratio of the input capacitance and the
feedback capacitor. Thus, CF can be selected to yield good
stability while maintaining high speed.
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
Without external compensation, the noise specification of
the OPA228 is the same as that for the OPA227 in gains of
5 or greater. With the additional external compensation, the
output noise of the of the OPA228 will be higher. The
amount of noise increase is directly related to the increase
in high frequency closed-loop gain established by the CIN/
CF ratio.
Figures 8 and 11 show the recommended circuit for gains
of +2 and –2, respectively. The figures suggest approximate
values for CF. Because compensation is highly dependent
on circuit design, board layout, and load conditions, CF
should be optimized experimentally for best results. Figures 9 and 10 show the large- and small-signal step responses for the G = +2 configuration with 100pF load
capacitance. Figures 12 and 13 show the large- and smallsignal step responses for the G = –2 configuration with
100pF load capacitance.
15pF
22pF
1kΩ
2kΩ
2kΩ
2kΩ
OPA228
OPA228
2kΩ
2kΩ
100pF
FIGURE 11. Compensation for OPA228 for G = –2.
5mV/div
5mV/div
FIGURE 8. Compensation of the OPA228 for G =+2.
OPA228
OPA228
400ns/div
400ns/div
FIGURE 12. Large-Signal Step Response, G = –2, CLOAD =
100pF, Input Signal = 5Vp-p.
25mV/div
25mV/div
FIGURE 9. Large-Signal Step Response, G = +2, CLOAD =
100pF, Input Signal = 5Vp-p.
OPA228
OPA228
200ns/div
200ns/div
FIGURE 10. Small-Signal Step Response, G = +2, CLOAD =
100pF, Input Signal = 50mVp-p.
FIGURE 13. Small-Signal Step Response, G = –2, CLOAD =
100pF, Input Signal = 50mVp-p.
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
100pF
www.ti.com
15
1.1kΩ
1.43kΩ
2.2nF
dc Gain = 1
330pF
1.1kΩ
1.65kΩ
VIN
1.43kΩ
1.91kΩ
OPA227
33nF
2.21kΩ
OPA227
68nF
VOUT
10nF
fN = 13.86kHz
fN = 20.33kHz
Q = 1.186
Q = 4.519
f = 7.2kHz
FIGURE 14. Three-Pole, 20kHz Low Pass, 0.5dB Chebyshev Filter.
20pF
0.1µF
100Ω
TTL INPUT
GAIN
“1”
“0”
+1
–1
100kΩ
9.76kΩ
500Ω
2
3
OPA227
6
Output
10kΩ
Input
D1
Dexter 1M
Thermopile
Detector
NOTE: Use metal film resistors
and plastic film capacitor. Circuit
must be well shielded to achieve
low noise.
D2
TTL
In
FIGURE 15. Long-Wavelength Infrared Detector Amplifier.
16
2
4.99kΩ
S1
S2
3
6
OPA227
Output
8
1
4.75kΩ
Responsivity ≈ 2.5 x 104V/W
Output Noise ≈ 30µVrms, 0.1Hz to 10Hz
Balance
Trim
4.75kΩ
1kΩ
DG188
Offset
Trim
+VCC
FIGURE 16. High Performance Synchronous Demodulator.
OPA227, 2227, 4227
OPA228, 2228, 4228
www.ti.com
SBOS110A
+15V
0.1µF
1kΩ
1kΩ
Audio
In
1/2
OPA2227
200Ω
To
Headphone
200Ω
1/2
OPA2227
This application uses two op amps
in parallel for higher output current drive.
0.1µF
–15V
FIGURE 17. Headphone Amplifier.
Bass Tone Control
R1
7.5kΩ
R2
50kΩ
3
1
CW
2
R3
7.5kΩ
R10
100kΩ
Midrange Tone Control
C1
940pF
R4
2.7kΩ
VIN
R5
50kΩ
3
CW
1
2
R6
2.7kΩ
C2
0.0047µF
Treble Tone Control
R7
7.5kΩ
R8
50kΩ
3
CW
1
2
R9
7.5kΩ
C3
680pF
R11
100kΩ
2
3
OPA227
6
VOUT
FIGURE 18. Three-Band ActiveTone Control (bass, midrange and treble).
OPA227, 2227, 4227
OPA228, 2228, 4228
SBOS110A
www.ti.com
17
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jan-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA2227P
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2227PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2227PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2227PG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2227U
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227U/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227U/2K5E4
ACTIVE
SOIC
D
8
2500
CU NIPDAU
Level-3-260C-168 HR
OPA2227U/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UA
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UA/2K5
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UA/2K5E4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UAE4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UAG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UE4
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2227UG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA2228P
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2228PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2228PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2228PG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA2228U
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228U/2K5
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228U/2K5E4
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228UA
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228UA/2K5
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228UA/2K5E4
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
Addendum-Page 1
Pb-Free
(RoHS)
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jan-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA2228UAE4
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA2228UE4
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA227P
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA227PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA227PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA227PG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA227U
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA227U/2K5
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA227U/2K5E4
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA227UA
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA227UA/2K5
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA227UA/2K5G4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA227UAG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA227UE4
ACTIVE
SOIC
D
8
100
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA228P
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA228PA
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA228PAG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA228PG4
ACTIVE
PDIP
P
8
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA228U
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA228UA
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA228UA/2K5
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA228UA/2K5E4
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA228UAG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA228UG4
ACTIVE
SOIC
D
8
100
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
OPA4227PA
ACTIVE
PDIP
N
14
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA4227PAG4
ACTIVE
PDIP
N
14
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
Addendum-Page 2
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jan-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
OPA4227UA
ACTIVE
SOIC
D
14
OPA4227UA/2K5
ACTIVE
SOIC
D
OPA4227UA/2K5G4
ACTIVE
SOIC
OPA4227UAG4
ACTIVE
OPA4228PA
58
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SOIC
D
14
58
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ACTIVE
PDIP
N
14
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
OPA4228UA
ACTIVE
SOIC
D
14
58
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA4228UA/2K5
ACTIVE
SOIC
D
14
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
OPA4228UAE4
ACTIVE
SOIC
D
14
58
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All products are sold
subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent
TI deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using TI components. To minimize the risks associated with customer
products and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent
right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine,
or process in which TI products or services are used. Information published by TI regarding third-party
products or services does not constitute a license from TI to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from TI under the patents or other intellectual
property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not
responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service
and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Mailing Address:
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated