VISHAY SI786LG-T1

Si786
Vishay Siliconix
Dual-Output Power-Supply Controller
FEATURES
D
D
D
D
Fixed 5-V and 3.3-V Step-down Converters
Less than 500-mA Quiescent Current per Converter
25-mA Shutdown Current
5.5-V to 30-V Operating Range
DESCRIPTION
The Si786 Dual Controller for Portable Computer Power
Conversion is pin and functionally compatible with the
MAX786 dual-output power supply controller for notebook
computers. The device is designed as a drop-in replacement
for that circuit.
The circuit is a system level integration of two step-down
controllers, micropower 5-V and 3.3-V linear regulators, and
two comparators. The controllers perform high efficiency
conversion of the battery pack energy (typically 12 V) or the
output of an ac to dc wall converter (typically 18-V to 24-V dc)
to 5-V and 3.3-V system supply voltages. The micropower
linear regulator can be used to keep power management and
back-up circuitry alive during the shutdown of the step-down
converters. The comparators can be biased at any voltage
between 2.7 V and the input voltage, simplifying battery
monitoring or providing sufficient voltage to enhance the gate
of a low on-resistance n-channel FET used in switching power
to different zones in the system.
A complete power conversion and management system can
be implemented with the Si786 Dual Controller for Portable
Computer Power Conversion, an inexpensive linear regulator,
the Si9140 SMP Controller for High Performance Processor
Power Supplies, five Si4410 n-channel TrenchFETR Power
MOSFETs, one Si4435 p-channel TrenchFET Power
MOSFET, and two Si9712 PC Card (PCMCIA) Interface
Switches.
The Si9130 Pin-Programmable Dual Controller for Portable
PCs is another integrated system level devices for portable PC
power systems.
The Si786 is available in both standard and lead (Pb)-free
28-pin SSOP packages and specified to operate over the (0_C
to 70_C), (−10_C to 90_C) and (−40_C to 85_C) temperature
ranges. See Ordering Information for corresponding part
numbers.
FUNCTIONAL BLOCK DIAGRAM
3.3 V
5.5. V
to
30 V
SHUTDOWN
5-V ON/OFF
3.3-V ON/OFF
SYNC
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Power
Section
5V
mP
Memory
Peripherals
Si786
Low-Battery Warning
Power-Good
www.vishay.com
1
Si786
Vishay Siliconix
ABSOLUTE MAXIMUM RATINGS
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 36 V
REF, VL Short to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Momentary
PGND to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "2 V
REF Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7 V
VL Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
BST3, BST5 to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 36 V
Continuous Power Dissipation (TA = 70_C)a
28-Pin SSOPb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 762 mW
LX3 to BST3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7 V to 0.3 V
LX5 to BST5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7 V to 0.3 V
Operating Temperature Range: (TMIN to TMAX)
Si786CG/CRG/CSG (C-Grade) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 70_C
Si786LG/LRG/LSG (L-Grade) . . . . . . . . . . . . . . . . . . . . . . . . . . . −10_ to 90_C
Si786DG/DRG/DSG (D-Grade) . . . . . . . . . . . . . . . . . . . . . . . . . −40_ to 85_C
Inputs/Outputs to GND
(D1, D2, SHDN, ON5, REF, SS5, CS5. FB5, SYNC, CS3, FB3,
SS3, ON3)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V, (VL + 0.3 V)
VH to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 20 V
Lead Temperature (soldering, 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . 300_C
Q1, Q2 to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V, (VH + 0.3 V)
DL3, DL5 to PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V, (VL + 0.3 V)
Notes
a. Device mounted with all leads soldered or welded to PC board.
b. Derate 9.52 mW/_C above 70_C.
DH3 to LX3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V (BST3 + 0.3 )
DH5 to LX5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V (BST5 + 0.3 )
Exposure to Absolute Maximum rating conditions for extended periods may affect device reliability. Stresses above Absolute Maximum rating may cause permanent
damage. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one
time
SPECIFICATIONS
Limitse
Specific Test Conditions
V+ = 15 V, IVL = IREF = 0 mA, SHDN = ON3 = ON5 = 5 V
Other Digital Input Levels 0 V or 5 V, TA = TMIN to TMAX
Parameter
Mina
Typb
Maxa
Unit
3.3-V and 5-V Step-Down Controllers
Input Supply Range
5.5
0 mV < (CS5-FB5) < 70 mV, 6 V < V + < 30 V
(includes load and line regulation)
FB5 Output Voltage
FB3 Output
p Voltage
g
0 mV < (CS3-FB3) < 70 mV
6 V < V + < 30 V
(includes load and line regulation)
30
4.80
5.08
5.20
Si786CG/LG/DG
3.17
3.35
3.46
Si786CRG/LRG/DRG
3.32
3.50
3.60
Si786CSG/LSG/DSG
3.46
3.65
3.75
V
Load Regulation
Either Controller (CS_ to FB_ = 0 to 70 mV)
2.5
%
Line Regulation
Either Controller (V+ = 6 V to 30 V)
0.03
%/V
Current Limit Voltage
Current-Limit
CS3-FB
FB3 or CS5-FB
FB5
Si786DG/DRG/DSG
SS3/SS5 Source Current
Si786DG/DRG/DSG
SS3/SS5 Fault Sink Current
80
100
120
77
100
120
2.5
4.0
6.5
2.3
4.0
6.5
2
mV
mA
mA
Internal Regulator and Reference
VL Output Voltage
VL Fault Lockout Voltage
VL/FB5 Switchover Voltage
REF Output Voltage
REF Fault Lockout Voltage
ON5 = ON3 = 0 V, 5.5 V < V+ < 30 V
0 mA < IL < 25 mA
4.5
5.5
Falling Edge, Hysteresis = 1%
3.6
4.2
Rising Edge of FB5, Hysteresis = 1%
4.2
4.7
3.24
3.36
No External
Loadc
Falling Edge
2.4
3.2
REF Load Regulation
0 mA < IL < 5 mAd
30
75
V+ Shutdown Current
SHDN = D1 = D2 = ON3 = ON5 = 0 V
V+ = 30 V
25
40
70
110
V+ Standby Current
Quiescent Power Consumption
(both PWM controllers on)
V+ Off Current
www.vishay.com
2
D1 = D2 = ON3 = ON5 = 0 V, V+ =
30 V
D1 = D2 = 0 V, FB5 = CS5 =
5 25 V
5.25
FB3 = CS3 = 3.5 V
Si786DG/DRG/DSG
Si786DG/DRG/DSG
FB5 = CS5 = 5.25 V, VL Switched Over to FB5
V
70
115
5.5
8.6
5.5
9.0
30
60
mV
mA
A
mW
mA
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
SPECIFICATIONS
Limitse
Specific Test Conditions
Parameter
V+ = 15 V, IVL = IREF = 0 mA, SHDN = ON3 = ON5 = 5 V
Other Digital Input Levels 0 V or 5 V, TA = TMIN to TMAX
Mina
Typb
Maxa
Unit
Comparators
D1, D2 Trip Voltage
D1, D2 Input Current
Q1, Q2 Source Current
Q1, Q2 Sink Current
Falling Edge,
Edge Hysteresis = 1%
Si786DG/DRG/DSG
1.69
1.60
1.69
D1 = D2 = 0 V, 5 V
VH = 15 V,
V VOUT = 2.5
25V
Q1, Q2 Output High Voltage
ISOURCE = 5 mA, VH = 3 V
Q1, Q2 Output Low Voltage
ISINK = 20 mA, VH = 3 V
Quiescent VH Current
1.61
"100
12
20
30
200
500
1000
VH - 0.5
0.4
VH = 18 V, D1 = D2 = 5 V, No External Load
4
10
270
300
330
260
300
330
170
200
230
165
200
230
V
nA
mA
V
mA
Oscillator and Inputs/Outputs
SYNC = 3.3
33V
Si786DG/DRG/DSG
Oscillator Frequency
SYNC = 0 V,
V 5V
Si786DG/DRG/DSG
SYNC High Pulse Width
200
SYNC Low Pulse Width
SYNC Rise/Fall Time
200
Input Low Voltage
Input High Voltage
Input Current
ns
Not Tested
Oscillator SYNC Range
Maximum Duty Cycle
kHz
200
240
350
SYNC = 3.3 V
89
92
SYNC = 0 V, 5 V
92
95
SHDN, ON3, ON5 SYNC
kHz
%
0.8
SHDN, ON3, ON5
2.4
SYNC
VL - 0.5
V
SHDN, ON3, ON5 VIN = 0 V, 5 V
"1
DL3/DL5 Sink/Source Current
VOUT = 2 V
1
DH3/DH5 Sink/Source Current
BST3 - LX3 = BST5 - LX5 = 4.5 V, VOUT = 2 V
1
mA
A
DL3/DL5 On-Resistance
High or Low
7
DH3/DH5 On-Resistance
High or Low
BST3 - LX3 = BST5 - LX5 = 4.5 V
7
W
Notes
a. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum.
b. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
c. The main switching outputs track the reference voltage. Loading the reference reduces the main outputs slightly according to the closed-loop gain (AVCL) and
the reference voltage load-regulation error. AVCL for the 3.3-V supply is unity gain. AVCL for the 5-V supply is 1.54.
d. Since the reference uses VL as its supply, its V+ line regulation error is insignificant.
e. Limits are for all temperature grades unless otherwise noted.
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
www.vishay.com
3
Si786
Vishay Siliconix
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
Efficiency vs. 5-V Output Current, 200 kHz
100
Efficiency vs. 5-V Output Current, 300 kHz
100
V+ = 6 V
V+ = 6 V
90
Efficiency (%)
Efficiency (%)
90
V+ = 15 V
80
V+ = 30 V
70
V+ = 15 V
80
V+ = 30 V
70
SYNC = 0 V, 3.3 V Off
3.3 V Off
60
60
50
50
0.001
0.01
0.1
1
10
0.001
0.01
5-V Output Current (A)
0.1
1
10
5-V Output Current (A)
Efficiency vs. 3.3-V Output Current, 200 kHz
Efficiency vs. 3.3-V Output Current, 300 kHz
100
100
90
90
V+ = 6 V
80
Efficiency (%)
Efficiency (%)
V+ = 6 V
V+ = 15 V
V+ = 30 V
70
80
V+ = 15 V
V+ = 30 V
70
SYNC = 0 V, 5 V On
5 V On
60
60
50
50
0.001
0.01
0.1
1
10
0.001
0.01
3.3-V Output Current (A)
Quiescent Supply Current vs. Supply Voltage
Quiescent Supply Current (mA)
30
25
1
10
Standby Supply Current vs. Supply Voltage
0.5
0.4
20
0.3
ON3 = ON5 = High
ON3 = ON5 = 0 V
15
0.2
10
0.1
5
0
0.0
0
6
12
18
Supply Voltage (V)
www.vishay.com
4
0.1
3.3-V Output Current (A)
24
30
0
6
12
18
24
30
Supply Voltage (V)
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
1.0
5-V Output
Still Regulating
Mimimum V IN to VOUT Differential (V)
100
Shutdown Supply Current ( m A)
Minimum VIN to VOUT Differential
vs. 5-V Output Current
Shutdown Supply Current vs. Supply Voltage
SHDN = 0 V
75
50
25
0.8
0.6
300 kHz
0.4
200 kHz
0.2
0
0.0
0
6
12
18
24
30
0.001
0.01
Supply Voltage (V)
0.1
1
10
5-V Output Current (A)
Switching Frequency vs. Load Current
1000.0
Switching Frequency (kHz)
SYNC = REF (300 kHz)
ON3 = ON5 = 5 V
100.0
10.0
5 V, V+ = 30 V
5 V, V+ = 7.5 V
1.0
3.3 V, V+ = 7.5 V
0.1
0.1
1
10
100
1000
Load Current (mA)
Pulse-Skipping Waveforms
Pulse-Width Modulation Mode Waveforms
5-V Output
50 mV/div
LX 10 V/div
2 V/div
5-V Output
50 mV/div
200 mS/div
ILoad = 100 mA
VIN = 10 V
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
500 ns/div
5-V Output Current = 1 A
VIN = 16 V
www.vishay.com
5
Si786
Vishay Siliconix
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
5-V Load-Transient Response
3.3-V Load-Transient Response
3A
LOAD CURRENT
3A
LOAD CURRENT
0A
0A
5-V Output
50 mV/div
200 mS/div
VIN = 15 V
200 mS/div
VIN = 15 V
5-V Line-Transient Response, Rising
5-V Line-Transient Response, Falling
5-V Output
50 mV/div
5-V Output
50 mV/div
VIN, 10 to 16 V
2 V/div
VIN, 16 to 10 V
2 V/div
20 mS/div
ILOAD = 2 A
20 mS/div
ILOAD = 2 A
3.3-V Line-Transient Response, Rising
3.3-V Line-Transient Response, Falling
20 mS/div
ILOAD = 2 A
www.vishay.com
6
3.3-V Output
50 mV/div
3.3-V Output
50 mV/div
3.3-V Output
50 mV/div
VIN, 10 to 16 V
2 V/div
VIN, 16 to 10 V
2 V/div
20 mS/div
ILOAD = 2 A
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
PIN DESCRIPTION AND ORDERING INFORMATION
CS3
1
28
FB3
SS3
2
27
DH3
ON3
3
26
LX3
D1
4
25
BST3
D2
5
24
DL3
VH
6
23
V+
Q2
7
22
VL
Q1
8
GND
SSOP-28
21
FB5
9
20
PGND
REF
10
19
DL5
SYNC
11
18
BST5
SHDN
12
17
LX5
ON5
13
16
DH5
SS5
14
15
CS5
Top View
PIN DESCRIPTION
Pin
Symbol
1
CS3
Current-sense input for 3.3-V Buck controller—this pins over current threshold is 100 mV with respect to FB3.
2
SS3
Soft-start input for 3.3 V. Connect capacitor from SS3 to GND.
3
ON3
ON/OFF logic input disables the 3.3-V Buck controller. Connect directly to VL for automatic turn-on.
4
D1
Comparator #1 noninverting input, threshold = 1.650 V. Comparator #1 output = Q1. Connect to GND if unused.
5
D2
Comparator #2 noninverting input (see D1).
6
VH
External bias supply-voltage input for comparators #1 and #2.
7
Q2
Comparator #2 output. Sources 20 mA from VH when D2 is high. Sinks 500 mA to GND when D2 is low regardless of VH input
voltage.
8
Q1
Comparator #1 output (see Q2).
9
GND
Analog ground.
10
REF
3.3-V reference output. Supplies external loads up to 5 mA.
11
SYNC
Oscillator control/synchronization input. Connect capacitor to GND, 1-mF/mA output or 0.22 mF minimum. For external clock
synchronization, a rising edge starts a new cycle to start. To use internal 200-kHz oscillator, connect to VL or GND. For
300-kHz oscillator, connect to REF.
12
SHDN
Shutdown logic input, active low. Connect to VL for automatic turn-on. The 5-V VL supply will not be disabled in shutdown allowing connection to SHDN.
13
ON5
ON/OFF logic input disables the 5-V Buck Controller. Connect to VL for automatic turn-on.
14
SS5
Soft-start control input for 5 V Buck controller. Connect capacitor from SS5 to GND.
15
CS5
Current-sense input for 5 V Buck controller—this pins over current threshold is 100 mV referenced to FB3.
16
DH5
Gate-drive output for the 5-V supply high-side n-channel MOSFET.
17
LX5
Inductor connection for the 5-V supply.
18
BST5
19
DL5
20
PGND
21
FB5
22
VL
5-V logic supply voltage for internal circuitry—able to source 5-mA external loads. VL remains on with valid voltage at V+.
23
V+
Supply voltage input.
24
DL3
Gate-drive output for the 3.3-V supply rectifying n-channel MOSFET.
25
BST3
26
LX3
Inductor connection for the 3.3-V supply.
27
DH3
Gate-drive output for the 3.3-V supply high-side n-channel MOSFET.
28
FB3
Feedback input for the 3.3-V Buck controller.
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Description
Boost capacitor connection for the 5-V supply.
Gate-drive output for the 5-V supply rectifying n-channel MOSFET.
Power Ground.
Feedback input for the 5-V Buck controller.
Boost capacitor connection for the 3.3-V supply.
www.vishay.com
7
Si786
Vishay Siliconix
ORDERING INFORMATION
Part Number
Lead (Pb)-Free
Part Number
Temp Range
Si786CG
Si786CG-T1
33V
3.3
Si786CG-T1—E3
Si786CRG
Si786CRG-T1
Si786CRG-T1—E3
C-Grade
0 to 70_C
Si786CSG
Si786CSG-T1
Si786LG
33V
3.3
Si786LG-T1—E3
Si786LRG
Si786LRG-T1
Si786LRG-T1—E3
L-Grade
−10_ to 90_C
Si786LSG
Si786LSG-T1
Si786DG
33V
3.3
Si786DG-T1—E3
Si786DRG
Si786DRG-T1
Si786DRG-T1—E3
D-Grade
−40_ to 85_C
Si786DSG
Si786DSG-T1
3 45 V
3.45
36V
3.6
Si786LSG-T1—E3
Si786DG-T1
3 45 V
3.45
36V
3.6
Si786CSG-T1—E3
Si786LG-T1
VOUT
3 45 V
3.45
36V
3.6
Si786DSG-T1—E3
Demo Board
Temp Range
Board Type
Si786DB
0 to 70_C
Surface Mount
DESCRIPTION OF OPERATION
The Si786 is a dual step-down converter, which takes a 5.5-V
to 30-V input and supplies power via two PWM controllers (see
Figure 1). These 5-V and 3.3-V supplies run on an optional
300-kHz or 200-kHz internal oscillator, or an external sync
signal. Amount of output current is limited by external
components, but can deliver greater than 6 A on either supply.
As well as these two main Buck controllers, additional loads
can be driven from two micropower linear regulators, one 5 V
(VL) and the other 3.3 V (REF)—see Figure 2. These supplies
are each rated to deliver 5 mA. If the linear regulator circuits fall
out of regulation, both Buck controllers are shut down.
Two voltage comparators with adjustable output voltages are
included in the Si786. They can be used for gate drive in load
switching applications, where n-channel MOSFETs are used.
Logic level voltages can be generated as well, for instance to
serve as mP interfacing (e.g. a Power-good signal).
3.3-V Switching Supply
The 3.3-V supply is regulated by a current-mode PWM
controller in conjunction with several externals: two n-channel
MOSFETs, a rectifier, an inductor and output capacitors (see
Figure 1). The gate drive supplied by DH3 needs to be greater
than VL , so it is provided by the bootstrap circuit consisting of
a 100-nF capacitor and diode connected to BST3 .
www.vishay.com
8
A low-side switching MOSFET connected to DL3 increases
efficiency by reducing the voltage across the rectifier diode. A
low value sense resistor in series with the inductor sets the
maximum current limit, to disallow current overloads at
power-on or in short-circuit situations.
The soft-start feature on the Si786 is capacitor programmable;
pin SS3 functions as a constant current source to the external
capacitor connected to GND. Excess currents at power-on are
avoided, and power-supplies can be sequenced with different
turn-on delay times by selecting the correct capacitor value.
5-V Switching Supply
The 5-V supply is regulated by a current-mode PWM controller
which is nearly the same as the 3.3-V output. The dropout
voltage across the 5-V supply, as shown in the schematic in
Figure 1, is 400 mV (typ) at 2 A. If the voltage at V+ falls, nearing
5 V, the 5-V supply will lower as well, until the VL linear regulator
output falls below the 4-V undervoltage lockout threshold.
Below this threshold, the 5-V controller is shut off.
The frequency of both PWM controllers is set at 300 kHz when
the SYNC pin is tied to REF. Connecting SYNC to either GND
or VL sets the frequency at 200 kHz.
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
3.3-V and 5-V Switching Controllers
Each PWM controller on the Si786 is identical with the
exception of the preset output voltages. The controllers only
share three functional blocks (see Figure 2): the oscillator, the
voltage reference (REF) and the 5-V logic supply (VL). The
3.3-V and 5-V controllers are independently enabled with pins
ON3 and ON5 , respectively. The PWMs are a direct-summing
type, without the typical integrating error amplifier along with
the phase shift which is a side effect of this type of topology.
Feedback compensation is not needed, as long as the output
capacitance and its ESR requirements are met, according to
the Design Considerations section of this data sheet.
The main PWM comparator is an open loop device which is
comprised of three comparators summing four signals: the
feedback voltage error signal, current sense signal,
slope-compensation ramp and voltage reference as shown in
Figure 3. This method of control comes closer to the ideal of
maintaining the output voltage on a cycle-by-cycle basis.
When the load demands high current levels, the controller is in
full PWM mode. Every cycle from the oscillator asserts the
output latch and drives the gate of the high-side MOSFET for
a period determined by the duty cycle (approximately
VOUT/VIN 100%) and the frequency. The high-side switch
turns off, setting the synchronous rectifier latch and 60ns later,
the rectifier MOSFET turns on. The low-side switch stays on
until the start of the next clock cycle in continuous mode, or
until the inductor current becomes positive again in
discontinuous mode. In over-current situations, where the
inductor current is greater than the 100-mV current-limit
threshold, the high-side latch is reset and the high-side gate
drive is shut off.
During low-current load requirements, the inductor current will
not deliver the 25-mV minimum current threshold. The
Minimum Current comparator signals the PWM to enter
pulse-skipping mode when the threshold has not been
reached. Pulse-skipping mode skips pulses to reduce
switching losses, the losses which decrease efficiency the
most at light load. Entering this mode causes the minimum
current comparator to reset the high-side latch at the beginning
of each oscillator cycle.
Soft-Start
To slowly bring up the 3.3-V and 5-V supplies, connect
capacitors from SS3 and SS5 to GND. Asserting ON3 or ON5
starts a 4-mA constant current source to charge these
capacitors to 4 V. As the voltage on these pins ramps up, so
does the current limit comparator threshold, to increase the
duty cycle of the MOSFETs to their maximum level. If ON3 or
ON5 are left low, the respective capacitor is discharged to
GND. Leaving the SS3 or SS5 pins open will cause either
controller to reach the terminal over-current level within 10 ms.
Soft start helps prevent current spikes at turn-on and allows
separate supplies to be delayed using external
programmability.
efficiency. The low-side rectifier is shut off when the inductor
current drops to zero.
Shoot-through current is the result when both the high-side
and rectifying MOSFETs are turned on at the same time.
Break-before-make timing internal to the Si786 manages this
potential problem. During the time when neither MOSFET is
on, the Schottky is conducting, so that the body diode in the
low-side MOSFET is not forced to conduct.
Synchronous rectification is always active when the Si786 is
powered-up, regardless of the operational mode.
Gate-Driver Boost
Synchronous Rectifiers
Synchronous rectification replaces the Schottky rectifier with
a MOSFET, which can be controlled to increase the efficiency
of the circuit.
When the high-side MOSFET is switched off, the inductor will
try to maintain its current flow, inverting the inductor’s polarity.
The path of current then becomes the circuit made of the
Schottky diode, inductor and load, which will charge the output
capacitor. The diode has a 0.5-V forward voltage drop, which
contributes a significant amount of power loss, decreasing
efficiency. A low-side switch is placed in parallel with the
Schottky diode and is turned on just after the diode begins to
conduct. Because the rDS(ON) of the MOSFET is low, the I*R
voltage drop will not be as large as the diode, which increases
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
The high-side n-channel drive is supplied by a flying-capacitor
boost circuit (see Figure 4). The capacitor takes a charge from
VL and then is connected from gate to source of the high-side
MOSFET to provide gate enhancement. At power-up, the
low-side MOSFET pulls LX_ down to GND and charges the
BST_ capacitor connected to 5 V. During the second half of the
oscillator cycle, the controller drives the gate of the high-side
MOSFET by internally connecting node BST_ to DH_. This
supplies a voltage 5 V higher than the battery voltage to the
gate of the high-side MOSFET.
Oscillations on the gates of the high-side MOSFET in
discontinuous mode are a natural occurrence caused by the
LC network formed by the inductor and stray capacitance at
the LX_ pins. The negative side of the BST_ capacitor is
connected to the LX_ node, so ringing at the inductor is
translated through to the gate drive.
www.vishay.com
9
Si786
Vishay Siliconix
SCHEMATIC DRAWINGS
INPUT
5.5 V to 30 V
100 W
C1
22 mF
D2A
1N4148
C10
22 mF
0.1 mF
D2B
1N4148
5 V at 5 mA
Si786
C5
0.1 mF
N1
R1
25 mW
3.3 V
at 3 A
25
27
L1
10 mH
26
D1
D1FS4
C7
150 mF
23
N3
24
1
C12
150 mF
28
(Note 1)
2
C9
0.01 mF
3
3.3 V ON/OFF
13
5 V ON/OFF
12
SHUTDOWN
11
OSC SYNC
9
10
Note 1: Use short, Kelvin-connected
PC board traces placed very
close to one another.
VL
V+
BST3
BST5
DH3
DH5
LX3
LX5
DL3
DL5
CS3
CS5
FB3
FB5
SS3
SS5
ON3
VH
ON5
D1
SHDN
Q1
SYNC
D2
GND
Q2
REF
PGND
22
18
10 mF
C4
0.1 mF
16
N2
L2
10 mH
17
19
R2
25 mW
5 V at
3A
D1
D1FS4
N3
C6
330 mF
15
21
14
6
(Note 1)
C8
0.01 mF
COMPARATOR SUPPLY INPUT
4
IN
8
COMPARATOR 1
OUT
5
IN
7
COMPARATOR 2
OUT
20
3.3 V at 5 mA
C3
1 mF
FIGURE 1. Si786 Application Circuit
V+
5-V LDO
Linear
Regulator
3.3-V
PWM
Controller
(See Figure 3)
VL
REF
3.3-V
Reference
ON
ON
4.5 V
SHDN
FB3
CS3
BST3
DH3
LX3
DL3
SS3
PGND
4V
ON3
FB5
CS5
2.8 V
SYNC
300 kHz/200 kHz
ON
Oscillator
STANDBY
5-V
PWM
Controller
(See Figure 3)
ON
BST5
DH5
LX5
DL5
SS5
ON5
VH
D1
Q1
1.65 V
D2
Q2
1.65 V
FIGURE 2. Si786 Block Diagram
www.vishay.com
10
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
CS
_
1X
60 kHz
LPF
REF, 3.3 V
(or Internal 5-V
Reference)
FB_
Summing
Comparator
R
S
BST_
Q
Level
Shift
DH
_
LX_
OSC
Slope
Comp
25 mV
Minimum Current
(Pulse-Skipping)
VL
Current
Limit
4 mA
0 mV to
100 mV
SS_
ON_
ShootThrough
Control
30R
3.3 V
1R
Synchronous
Rectifier Control
R
S
VL
Q
Level
Shift
DL_
PGND
FIGURE 3. Si786 Controller Block Diagram
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
www.vishay.com
11
Si786
Vishay Siliconix
BATTERY
INPUT
VL
VL
BST_
DH_
Level
Translator
PWM
LX_
VL
DL_
FIGURE 4. Boost Supply for Gate Drivers
OPERATIONAL MODES
PWM Mode
The 3.3-V and 5-V Buck controllers operate in
continuous-current PWM mode when the load demands more
than approximately 25% of the maximum current (see typical
curves). The duty cycle can be approximated as Duty_Cycle
= VOUT/VIN .
In this mode, the inductor current is continuous; in the first half
of the cycle, the current slopes up when the high-side
MOSFET conducts and then, in the second half, slopes back
down when the inductor is providing energy to the output
capacitor and load. As current enters the inductor in the first
half-cycle, it is also continuing through to the load; hence, the
load is receiving continuous current from the inductor. By using
this method, output ripple is minimized and smaller form-factor
inductors can be used. The output capacitor’s ESR has the
largest effect on output ripple. It is typically under 50 mV; the
worst case condition is under light load with higher input
battery voltage.
www.vishay.com
12
Pulse-Skipping Mode
When the load requires less than 25% of its maximum, the
Si786 enters a mode which drives the gate for one clock cycle
and skips the majority of the remaining cycles. Pulse-skipping
mode cuts down on the switching losses, the dominant power
consumer at low current levels.
In the region between pulse-skipping mode and PWM mode,
the controller may transition between the two modes,
delivering spurts of pulses. This may cause the current
waveform to look irregular, but will not overly affect the ripple
voltage. Even in this transitional mode efficiency will stay high.
Current Limit
The current through an external resistor, is constantly
monitored to protect against over-current. A low value resistor
is placed in series with the inductor. The voltage across it is
measured by connecting it between CS_ and FB_. If this
voltage is larger than 100 mV, the high-side MOSFET drive is
shut down. Eliminating over-currents protects the MOSFET,
the load and the power source. Typical values for the sense
resistors with a 3-A load will be 25 mW.
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
Si786
Vishay Siliconix
Oscillator and SYNC
DESIGN CONSIDERATIONS
There are two ways to set the Si786 oscillator frequency: by
using an external SYNC signal, or using the internal oscillator.
The SYNC pin can be driven with an external CMOS level
signal with frequency from 240 kHz and 350 kHz to
synchronize to the internal oscillator. Tying SYNC to either VL
or GND sets the frequency to 200 kHz and to REF sets the
frequency to 300 kHz.
Inductor Design
Three specifications are required for inductor design:
inductance (L), peak inductor current (ILPEAK), and coil
resistance (RL). The equation for computing inductance is:
L+
Operation at 300 kHz is typically used to minimize output
passive component sizes. Slower switching speeds of
200 kHz may be needed for lower input voltages.
ǒV OUTǓǒVIN(MAX)–VOUTǓ
ǒVIN(MAX)Ǔ(f)ǒIOUTǓ(LIR)
Where:
Internal VL and REF
A 5-V linear regulator supplies power to the internal logic
circuitry. The regulator is available for external use from pin VL ,
able to source 5 mA. A 10-mF capacitor should be connected
between VL and GND. To increase efficiency, when the 5 V
switching supply has voltage greater than 4.5 V, VL is internally
switched over to the output of the 5-V switching supply and the
linear regulator is turned off.
The 5-V linear regulator provides power to the internal 3.3-V
bandgap reference (REF). The 3.3-V reference can supply 5
mA to an external load, connected to pin REF. Between REF
and GND connect a capacitor, 0.22 mF plus 1 mF per mA of load
current. The switching outputs will vary with the reference;
therefore, placing a load on the REF pin will cause the main
outputs to decrease slightly, within the specified regulation
tolerance.
VOUT = Output voltage (3.3 V or 5 V);
VIN(MAX) = Maximum input voltage (V);
f = Switching frequency, normally
300 kHz;
IOUT = Maximum dc load current (A);
LIR = Ratio of inductor peak-to-peak ac current to
average dc load current, typically 0.3.
When LIR is higher, smaller inductance values are acceptable,
at the expense of increased ripple and higher losses.
The peak inductor current (ILPEAK) is equal to the steady-state
load current (IOUT) plus one half of the peak-to-peak ac current
(ILPP). Typically, a designer will select the ac inductor current
to be 30% of the steady-state current, which gives ILPEAK equal
to 1.15 times IOUT .
The equation for computing peak inductor current is:
ILPEAK + IOUT )
ǒVOUTǓǒVIN(MAX)–V OUTǓ
(2)(f)(L)ǒVIN(MAX)Ǔ
Output Capacitors
VL and REF supplies stay on as long as V+ is greater than 4.5
V, even if the switching supplies are not enabled. This feature
is necessary when using the micropower regulators to keep
memory alive during shutdown.
The output capacitors determine loop stability and ripple
voltage at the output. In order to maintain stability, minimum
capacitance and maximum ESR requirements must be met
according to the following equations:
Both linear regulators can be connected to their respective
switching supply outputs. For example, REF would be tied to
the output of the 3.3 V and VL to 5 V. This will keep the main
supplies up in standby mode, provided that each load current
in shutdown is not larger than 5 mA.
CF u
VREF
ǒVOUTǓǒRCSǓ(2)(p)(GBWP)
and,
ESRCF t
ǒVOUTǓǒRCSǓ
VREF
Fault Protection
Where:
The 3.3 V and 5 V switching controllers as well as the
comparators are shut down when one of the linear
regulators drops below 85% of its nominal value; that is, shut
down will occur when VL < 4.0 V or REF < 2.8 V.
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
CF = Output filter capacitance (F)
VREF = Reference voltage, 3.3 V;
VOUT = Output voltage, 3.3 V or 5 V;
RCS = Sense resistor (W);
GBWP = Gain-bandwidth product, 60 kHz;
ESRCF = Output filter capacitor ESR (W).
www.vishay.com
13
Si786
Vishay Siliconix
Both minimum capacitance and maximum ESR requirements
must be met. In order to get the low ESR, a capacitance value
of two to three times greater than the required minimum may
be necessary.
The equation for output ripple in continuous current mode is:
VOUT(RPL) + ILPP(MAX)
ǒ
ESRCF )
ǒ2
1
Pxf
Ǔ
C FǓ
Lower Voltage Input
The application circuit shown here can be easily modified to
work with 5.5-V to 12-V input voltages. Oscillation frequency
should be set at 200 kHz and increase the output capacitance
to 660 mF on the 5-V output to maintain stable performance up
to 2 A of load current. Operation on the 3.3-V supply will not be
affected by this reduced input voltage.
The equations for capacitive and resistive components of the
ripple in pulse-skipping mode are:
VOUT(RPL)(C) +
VOUT(RPL)(R) +
(4)ǒ10–4Ǔ(L)
ǒRCS 2ǓǒC FǓ
ǒ
Ǔ
1 )
1
VOUT VIN–V OUT
(0.02)ǒESRCFǓ
R CS
The total ripple, VOUT(RPL) , can be approximated
as follows:
if VOUT(RPL)(R) < 0.5 VOUT(RPL)(C),
then VOUT(RPL) = VOUT(RPL)(C),
otherwise, VOUT(RPL) = 0.5 VOUT(RPL)(C) +
VOUT(RPL)(R).
www.vishay.com
14
Document Number: 70189
S-40807—Rev. J, 26-Apr-04