MURATA NMJ0505SAC

NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
SELECTION GUIDE
FEATURES
RoHS compliant
UL60950 recognized
Power density 0.42W/cm3
Wide temperature performance at full
1 watt load, –40°C to 60°C
Single and dual outputs
UL 94V-0 package material
No heatsink required
Footprint 1.91cm2
Order Code
Nominal
Input
Voltage
V
NMJ0505SC
NMJ0509SC
NMJ0512SC
NMJ0515SC
NMJ1205SC
NMJ1209SC
NMJ1212SC
NMJ1215SC
NMJ0303SAC
NMJ0503SAC
NMJ0505SAC
NMJ0509SAC
NMJ0512SAC
NMJ0515SAC
NMJ1205SAC
NMJ1209SAC
NMJ1212SAC
NMJ1215SAC
5
5
5
5
12
12
12
12
3.3
5
5
5
5
5
12
12
12
12
Output
Voltage
Efficiency
Isolation
(Min.)
Capacitance
Output
Current
Ripple &
Noise4
V
mA
mV p-p
%
pF
kHrs
±5
±9
±12
±15
±5
±9
±12
±15
3.3
3.3
5
9
12
15
5
9
12
15
±100
±55
±42
±33
±100
±55
±42
±33
303
303
200
111
83
66
200
111
83
66
40
30
20
20
40
30
20
20
70
60
50
50
50
50
50
50
50
50
60
65
65
65
60
65
65
65
66
64
68
72
71
71
69
73
73
74
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
4950
3832
2770
1903
3688
3029
2324
1682
13780
13460
13360
12700
11490
9980
8447
8176
7660
6950
Contact Factory
MTTF1
When operated with additional external load capacitance the rise time of the input voltage will determine the maximum external
capacitance value for guaranteed start up. The slower the rise time of the input voltage the greater the maximum value of the
additional external capacitance for reliable start up.
SIP package style
5.2kVDC isolation
3V, 5V & 12V input
3V, 5V, 9V, 12V and 15V output
Internal SMD construction
INPUT CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Units
Voltage range
Continuous operation, 3V input types
Continuous operation, 5V input types
Continuous operation, 12V input types
2.97
4.5
10.8
3.3
5
12
3.63
5.5
13.2
V
Min.
Typ.
Max.
Units
1
W
Fully encapsulated with toroidal magnetics
Pin compatible with the NMV series SIP
DC/DC converters
MTTF up to 13 million hours
Custom solutions available
PRODUCT OVERVIEW
The NMJ series are dual and single output
DC/DC converters in a 7 pin SIP package style
offering pin and functionality compatibility with
the NMV series SIP DC/DC converters. The NMJ
series is UL60950 recognized and suitable for
applications where safety and miniaturisation
are of paramount importance. Isolation barrier
approved for supplementary/reinforced insulation
- see page 2.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com
OUTPUT CHARACTERISTICS
Parameter
Rated Power2
Voltage Set Point Accuracy
Line regulation
Load regulation
Single outputs
Load regulation
Dual outputs
Zero Load Power Consumption
Conditions
TA=-40ºC to 60ºC
See tolerance envelopes
High VIN to low VIN
10% load to rated load, xx03
10% load to rated load, 0505
10% load to rated load, 0509, 0512, 0515
10% load to rated load, 12xx
10% load to rated load, 5V output types
10% load to rated load, 9V output types
10% load to rated load, 12V output types
10% load to rated load, 15V output types
All types
1.0
10.0
7.0
6.0
5.0
10.0
6.0
6.0
6.0
250
1.2
15.0
10.0
10.0
7.0
15.0
10.0
10.0
10.0
%/%
%
%
mW
ABSOLUTE MAXIMUM RATINGS
Short-circuit protection3
Lead temperature 1.5mm from case for 10 seconds
Input voltage VIN, NMJ03 types
Input voltage VIN, NMJ05 types
Input voltage VIN, NMJ12 types
1 second
300°C
5V
7V
15V
1. Calculated using MIL-HDBK-217 FN2 calculation model with nominal input voltage at full load.
2. See derating graph.
3. Supply voltage must be discontinued at the end of the short circuit duration.
4. See ripple & noise test method.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 1 of 6
NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Conditions
Min.
Isolation test voltage
Resistance
Flash tested for 1 second
Viso= 500VDC
5200
Parameter
Conditions
Min.
Switching frequency
Single output
Dual output
Typ.
Max.
Units
VDC
GΩ
1
GENERAL CHARACTERISTICS
Typ.
Max.
Units
45
70
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Min.
Specification
Storage
Case Temperature above ambient
Cooling
All output types
-40
-55
All output types
Free air convection
TEMPERATURE DERATING GRAPH
TOLERANCE ENVELOPE
1.0
0
-40
0
40
Ambient Temperature (ºC)
oad Line
VNOM
Safe Operating Area
80
°C
100
+1%
oad Lin
e
VNOM
-4%
75
50
25
Output Load Current (%)
Typical
L
+2.5%
-7.5%
10
Units
60
130
33
+9%
Typical
L
Output Voltage
+6%
60ºC
Max.
TOLERANCE ENVELOPE, 3.3V in, 3V out type only
+10%
Output Voltage
Output Power (W)
1.5
0.5
Typ.
+1%
-7%
-7%
-15%
10
75
50
25
Output Load Current (%)
100
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test
voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMJ series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 5.2kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
The NMJ series has been recognized by Underwiters Laboratory to 300Vrms for Supplementary Insulation and 150Vrms for Reinforced Insulation.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on
materials, construction and environment. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be
reduced by 20% from specified test voltage.
SAFETY APPROVAL
The NMJ series has been recognised by Underwriters Laboratory (UL) to UL 60950 for supplementary insulation up to 300Vrms and reinforced insulation up to 150Vrms at a
maximum ambient temperature of 60ºC. File number E179522 applies.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300ºC for 10 seconds. The pin termination finish
on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering
systems.
For further information, please visit www.murata-ps.com/rohs
www.murata-ps.com
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 2 of 6
NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
OUTPUT RIPPLE REDUCTION
By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max.
Component selection
Capacitor: It is required that the ESR (Equivalent Series Resistance) should be as low as possible, ceramic types are recommended.
The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter.
Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be
such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz.
L
Power
Source
L, μH
DC
Inductor
Through Hole
SMD
Consult Factory
Consult Factory
Consult Factory
Consult Factory
Consult Factory
3.3V single output types
5V single output types
9V single output types
12V single output types
15V single output types
+VOUT
Power
Source
Load
C
DC
DC
DC
Capacitor
Size
V rating, V
C, μF
4.70
Capacitor
Size
1206
V rating, V
10
0.47
0805
25
C, μF
L
C
Load
C
Load
OV
-VOUT
L
5V dual output types
9V dual output types
12V dual output types
15V dual output types
www.murata-ps.com
L, μH
22
Inductor
Through Hole
22R223C
68
22R224C
SMD
82223C
Consult Factory
82224C
Consult Factory
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 3 of 6
NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
OUTPUT RIPPLE REDUCTION (continued)
SMD option 8200 Inductor Series Mechanical Dimensions
Through hole option 2200R Inductor Series Mechanical Dimensions
0.283±0.020
(7.2±0.50)
0.7
(0.028)
Min.
103C
0.335±0.020
(8.5±0.50)
0.413 (10.50) Max.
2.5 (0.0984)
±0.2 (0.008)
332C
3.2 (0.126)
±0.3 (0.012)
2.0 (0.080)
±0.3 (0.012)
2.5 (0.098)
±0.2 (0.008)
Recommended pad layout
3.81 (0.15)
1.772±0.130
(45.00±3.30)
3.05 (0.120)
1.614±0.130
(41.00±3.30)
1.52
(0.060)
0.024±0.002
(0.60±0.05)
Recommended footprint
Ø0.047
+0.006
+0.15
Ø1.20
-0.000
-0.00
0.118(3.00)
All dimensions in inches (mm).
All dimensions in inches (mm).
For more information please visit www.murata-ps.com
www.murata-ps.com
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 4 of 6
NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
CHARACTERISATION TEST METHODS
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test configuration.
C1
C2
C3
R1
R2
T1
RLOAD
R3
1uF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10uF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon film, +/-1% tolerance
50Ω BNC termination
3T of the coax cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
50Ω resistor, carbon film, +/-1%
Measured values are multiplied by 10 to obtain the specified values.
Differential Mode Noise Test Schematic
DC/DC Converter
OSCILLOSCOPE
C1 C2 C3
+
SUPPLY
Input
-
+
R1
T1
R2
Y INPUT
Output
-
R LOAD
www.murata-ps.com
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 5 of 6
NMJ Series
5.2kVDC Isolated 1W DC/DC Converters
PACKAGE SPECIFICATIONS
PIN CONNECTIONS
MECHANICAL DIMENSIONS
0.77 (19.50)
Dual Output
Pin
0.39
(9.80)
Single Output
Function
1
2
5
6
7
Pin
+VIN
-VIN
-VOUT
OV
+VOUT
+VIN
-VIN
-VOUT
+VOUT
RECOMMENDED FOOTPRINT DETAILS
0.49 (12.50)
x5 HOLES Ø
0.18 (4.60)
1
0.14 (3.60)
Function
1
2
5
7
5
2
6*
0.1 (2.54)
7
0.022 (0.55)
0.018 (0.45)
0.045 (1.15)
0.039 (1.00)
0.004 (0.10)
*
0.022 (0.55)
0.018 (0.45)
0.1 (2.54)
Weight: 4.3g
0.1 (2.54)
* Hole not required for single output variants.
All dimensions in inches ±0.01 (mm ±0.25mm).
0.094 (2.40)
0.074±0.03 (1.88±0.75)
0.012 (0.30)
0.008 (0.20)
TUBE OUTLINE DIMENSIONS
All dimensions in inches ±0.01 (mm ±0.25mm). All pins on a 0.1 (2.54) pitch and within
±0.01 (0.25) of true position.
* Pin not fitted on single output variants.
œ
œ
Unless otherwise stated all dimensions in inches ±0.02 (mm ±0.5mm).
Tube length : 20.669±0.079 (525mm±2mm).
USA:
Tube Quantity : 25
Mansfield (MA), Tel: (508) 339-3000, email: [email protected]
Canada: Toronto, Tel: (866) 740 1232, email: [email protected]
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: [email protected] ISO 9001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2008 Murata Power Solutions, Inc.
www.murata-ps.com
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected]
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected]
Germany: München, Tel: +49 (0)89-544334-0, email: [email protected]
Japan:
Tokyo, Tel: 3-3779-1031, email: [email protected]
Osaka, Tel: 6-6354-2025, email: [email protected]
Website: www.murata-ps.jp
China:
Shanghai, Tel: +86 215 027 3678, email: [email protected]
Guangzhou, Tel: +86 208 221 8066, email: [email protected]
Technical enquiries - email: [email protected], tel: +44 (0)1908 615232
KDC_NMJC.G02 Page 6 of 6