Panasonic New Product Introduction New PAN1026 Series Place and Play Bluetooth® Module RoHS COMPLIANT Dual Mode, Place and Play Bluetooth Module Introducing Panasonic’s Bluetooth dual mode, place and play RF module, the PAN1026 featuring an embedded ARM processor, Bluetooth 4.0, serial port profile (SPP), command set API and integrated antenna. This cost-engineered solution is based on a single chip solution that integrates an ARM processor with a Bluetooth controller. Bluetooth 4.0 combines the data rate of Bluetooth Classic (3Mb/s) and ultra-fast connection time of Bluetooth Low Energy (3mS). Bluetooth Low Energy is designed to create low data rate networks using a minimum amount of power. The embedded serial port profile (SPP) frees application resources while the command set API creates a simple but flexible firmware interface. An onboard antenna does away with 2.4GHz RF circuit complexity. Created with the design engineer in mind, product design cycles are greatly reduced using Panasonic’s free of charge reference design and design review services1. PCB layouts are simplified using available Gerber files and minimized with Panasonic’s tiny footprint technology. The module is just 15.6mm x 8.7mm x 1.9mm and fully shielded to improve immunity. All Panasonic Bluetooth RF modules carry FCC, IC, CE and Bluetooth certifications. The PAN1026 recognizes Apple’s authentication coprocessor and supports Bluetooth communication2 with Apple’s iPhone and iPad®. Connectivity also includes Android, smart phones and all Bluetooth enabled devices3. Prototyping and testing are accelerated by utilizing the EVAL_PAN1026 development kit and EasyDualMode software development environment. The EVAL_PAN1026 contains two PAN1026ETU development modules on Panasonic’s ETU platform – ETU for Easy to Use. EasyDualMode allows both BLE and Bluetooth Classic application development in a single environment. EasyDualMode software is available free of charge on Panasonic’s RF module website. PAN1026ETU Development Module 1. Services are reserved for qualified customers. Contact one of Panasonic manufacturer’s sales representatives for more information. 2. Apple authentication coprocessor and MFI certification are required for communicating with Apple Idevices. 3. Connectivity requires that devices support Bluetooth Serial Port Profile *Apple iPad and iPhone are trademarks of Apple Inc Features • Bluetooth Version 4.0 • Industrial Temperature Range, -40 to +85°C • High Sensitivity: -87dbm • Output Power: 4dbm • Single VCC Supply: 1.7 to 3.6 V • WiFi Coexistence • High-Speed Interfaces: USB 2.0 UART up to 4.3 Mbps • Integrated ARM 32-Bit Processor Website: www.panasonic.com/industrial [email protected] 1-800-344-2112 Applications • iOS and Android Devices • Wireless Sensors • Cable Replacement • Instrumentation • Medical • Automotive Copyright © 2013 Panasonic Corporation of North America. All Rights Reserved. Specifications are subject to change without notice. PAN1026 Series NPI, FY13-078-XXX Block Diagram (PAN1026) EEPROM VSUPPLY Audio PCM/I2S/USB Toshiba TC35661 1-Chip LSI UART Filter Slow Clock 32.768 kHz Crystal 26 MHz Technical Characteristics Parameter Value Condition Receiver Sensitivity -87 dBm typ. Ideal Signal Output Power +4 dBm typ. @ 50 Ohm Antenna Pin Power Supply 1.7 to 3.6 V Single Voltage Operation Transmit 46 mA ACL, DH1 Receive 46 mA ACL, DH1 Operating Temperature -40 to +85°C Ordering Information Part Number Description ENW-89837A3KF PAN1026 Bluetooth Module, SPP, Integrated Antenna EVAL_PAN1026 PAN1026 Evaluation Kit Additional Information For detailed specification information on the PAN1026 Place and Play Bluetooth Module, visit our website at: http://www.panasonic.com/rfmodules/ Website: www.panasonic.com/industrial [email protected] 1-800-344-2112 Copyright © 2013 Panasonic Corporation of North America. All Rights Reserved. Specifications are subject to change without notice. PAN1026 Series NPI, FY13-078-XXX