Source C-13-1250AC-F-SLCA-11-G5 1.25 gbps single mode sff lc transceiver Datasheet

1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Complies with IEEE 802.3 Gigabit Ethernet
• Single +3.3V Power Supply
• CML AC-coupled Differential Inputs and Outputs
• LVTTL Signal Detection Output
• Class 1 Laser International Safety Standard IEC 825 Compliant
• Solder ability to MIL-STD-883, Method 2003
• Pin coating is Sn/Pb with minimum 2% Pb content
• Flammability to UL94V0
• Humidity RH-5-85% (5-95% short term) to IEC 68-2-3
• Complies with Telcordia(Bellcore) GR-468-CORE
• Uncooled laser diode with MQW structure
• 1.25 Gbps Ethernet Links
• 1.06 Gbps Fiber Channel
• RoHS compliance available
Absolute Maximum Rating
Symbol
Min.
Max.
Unit
Power Supply Voltage
Parameter
Vcc
0
3.6
V
Total Current
Iout
0
240
mA
-
-
260
ºC
Tstg
-40
85
ºC
Soldering Temperature
Storage Temperature
Note
10 seconds on leads only
Recommended Operating Condition
Symbol
Min.
Typ.
Max.
Unit
Power Supply Voltage
Parameter
Vcc
3.1
3.3
3.5
V
Operating Temperature
Topr
-20
-
85
ºC
-
1062.5
-
1250
Mbps
Data Rate
Transmitter Specifications, Optical
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Optical
Optical Transmit Power
Po
-9
-
-3
dBm
Output center Wavelength
λ
1270
1310
1360
nm
∆λrms
-
-
3
nm
ER
9
-
-
dB
Output Spectrum Width
Extinction Ratio
Output Eye
RMS(σ)
Compliant with IEEE 802.3
Optical Rise Time
tr
-
-
0.16
ns
20% to 80% Values
Optical Fall Time
tf
-
-
0.16
ns
20% to 80% Values
RIN
-
-
-118
dB/Hz
TJ
-
-
90
ps
Relative Intensity Noise
Total Jitter
LUMINENTOIC.COM
Measured with 27-1 PRBS
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Transmitter Specifications, Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Notes
ICC
-
-
130
mA
Maximum current is specified at Vcc=
Maximum @ maximum temperature
at -20~85ºC
Differential Data Input Voltage
VIH-VIL
500
-
2200
mV
AC-coupled
Tx_DISABLE Input Voltage-Low
VIL
2.0
-
Vcc+0.3
V
Tx_DISABLE Input Voltage-High
VIH
0
-
0.8
V
Symbol
Min
Typical
Max
Unit
Notes
-
-
-25
-23
dBm
Measured with 27-1 PRBS, BER=1E-12
Pin
0
-
-
dBm
Electrical
Power Supply Current
Receiver Specifications, Optical
Parameter
Optical
Sensitivity
Maximum Input Power
Signal Detect-Asserted
Pa
-
-
-21
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-30
-
-27
dBm
Measured on transition: high to low
0.5
3
5
dB
1100
-
1600
nm
Signal Detect-Hysteresis
Wavelength of Operation
Receiver Specifications, Electrical
Parameter
Symbol
Min
Typical
Max
Unit
ICC
-
-
110
mA
Note
Electrical
Power Supply Current
Differential Data Output Voltage
VOH -VOL
600
-
1600
V
Signal Detect Output Voltage-Low
VSDL
-
-
0.5
V
Signal Detect Output Voltage-High
VSDH
2.0
-
Vcc
V
LUMINENTOIC.COM
The current excludes the output load
current at -20~85ºC
AC-coupled
LVTTL
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Connection Diagram
PIN
Symbol
Notes
1
RxGND
Directly connect this pin to the receiver ground plane
2
RxVcc
+3.3V dc power for the receiver section
3
SD
Active high on this indicates a received optical signal(LVTTL )
4
RD-
Receiver Data Out Bar (CML)
5
RD+
Receiver Data Out (CML)
6
TxVcc
7
TxGND
+3.3V dc power for the trasmitter section
Directly connect this pin to the transmitter ground plane
8
Warnings
TxDIS
9
TD+
Transmitter Data In (CML)
10
TD-
Transmitter Data In Bar (CML)
Attaching Posts
LUMINENTOIC.COM
Transmitter disable (LVTTL)
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Recommended Circuit Schematic
C-13-1250AC-F-SLCA-11-G5
TX_DIS
8
TTL logic level
TX_GND 7
Z=50�
TRANSMITTER
TX_D 9
DRIVER
TD +
Z=50�
TX_D 10
TD -
LASER
Vcc_TX
Vcc_RX
SD
BIAS
PIN
TZ
AMP
RECEIVER
POST
AMP
6
2
3
See
Fig. 3
Note 1
Serializer / De-Serializer
with LV PECL lnputs/Outputs
See
Fig. 2
Vcc= +3.3V
Z=50�
RX_D
4
RX_D
5
RX_GND
1
82Ω
82Ω
Z=50�
RD -
RD +
130Ω
130Ω
Figure 1: Recommended Transceiver and Receive Data Terminations (AC-coupled)
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Signal Detect (LVTTL output)
The C-13-1250AC-F-SLCA-11-G5 transceivers are equipped with LVTTL signal detect output. The standard LVTTL output
the need for a CML to LVTTL level shifter in most applications.
eliminates
R1
R=130k� or N.C
Figure 2: Signal Detect
Power Coupling
A suggested layout for power and ground connections is given in figure 3A below. Connections are made via separate voltage and
ground planes. The mounting posts are at case ground and should not be connected to circuit ground. The mounting posts are at case ground
and should not be connected to circuit ground. The ferrite bead should provide a real impedance of 50 to 100 ohms at 100 to 1000 MHz. Bypass capacitors should be placed as close to the 10-pin connector as possible.
L2
Vcc
L1
C1
C3
C4
C2
VALUES:
C1, C2 = 1000pF,
C3, = 0.1 uF
C4, = 10 uF,
L1, L2 = Real impednce of 50 to
100 Ohms to 1000 MHz.
Figure 3: Suggested Power Coupling-Electrical Schematic
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Package Diagram
Printed Circuit Board Layout Consideration
A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies signals
that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the receiver
circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit. To minimize
the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must be
used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of power
and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of signal
traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high speed
signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter be
used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Ordering Information
Available Option:
C-13-1250AC-F-SLCA-11-G5
Part numbering Definition:
C - 13 - 1250AC - F - S LC TxPower Temperature and Package -11
RoHS
• 13 = Wavelength 1310 nm
• 1250 Mbps
1250AC = AC-coupled signal, LVTTL SD output
• F = +3.3V SFF Transceiver, FP
• Single mode fiber
• Connector options
• Tx Power range
Blank = -10 to -3 dBm, 10km reach
• Temperature range
A = industrial temperature
• -11 = 6 ground posts
• RoHS
G5 = RoHS 5/6-compliant product (lead exemption)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS1912-Jun1808
Rev A.0
1.25 Gbps Single Mode SFF LC Transceiver
C-13-1250AC-F-SLCA-11-G5
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS1912-Jun1808
Rev A.0
Similar pages