TI1 ADS5545 14-bit, 170 msps adc with ddr lvds/cmos output Datasheet

ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
14-BIT, 170 MSPS ADC WITH DDR LVDS/CMOS OUTPUTS
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Maximum Sample Rate: 170 MSPS
14-Bit Resolution
No Missing Codes
Total Power Dissipation 1.1 W
Internal Sample and Hold
74-dBFS SNR at 70-MHz IF
85-dBc SFDR at 70-MHz IF, 0 dB gain
11.4 ENOB Minimum at 70-MHz IF
Double Data Rate (DDR) LVDS and Parallel
CMOS Output Options
Programmable Gain up to 6 dB for SNR/SFDR
Trade-Off at High IF
Reduced Power Modes at Lower Sample
Rates
Supports input clock amplitude down to
400 mVPP
Clock Duty Cycle Stabilizer
No External Reference Decoupling Required
Internal and External Reference Support
Programmable Output Clock position to ease
data capture
3.3-V Analog and Digital Supply
48-QFN Package (7 mm × 7 mm)
Wireless Communications Infrastructure
Software Defined Radio
Power Amplifier Linearization
802.16d/e
Test and Measurement Instrumentation
High Definition Video
Medical Imaging
Radar Systems
DESCRIPTION
ADS5545 is a high performance 14-bit, 170-MSPS
A/D converter. It offers state-of-the-art functionality
and performance using advanced techniques to
minimize board space. Using an internal sample and
hold and low jitter clock buffer, the ADC supports
both high SNR and high SFDR at high input
frequencies. It features programmable gain options
that can be used to improve SFDR performance at
lower full-scale analog input ranges.
In a compact 48-pin QFN, the device offers fully
differential LVDS DDR (Double Data Rate) interface
while parallel CMOS outputs can also be selected.
Flexible output clock position programmability is
available to ease capture and trade-off setup for hold
times. At lower sampling rates, the ADC can be
operated at scaled down power with no loss in
performance. ADS5545 includes an internal
reference, while eliminating the traditional reference
pins and associated external decoupling. The device
also supports an external reference mode.
The device is specified over
temperature range (-40°C to 85°C).
the
industrial
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2007, Texas Instruments Incorporated
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
CLKP
DRGND
DRVDD
AGND
AVDD
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
CLKOUTP
CLOCKGEN
CLKM
CLKOUTM
D0_D1_P
D0_D1_M
D2_D3_P
D2_D3_M
D4_D5_P
D4_D5_M
Digital
Encoder
and
Serializer
INP
14-Bit
ADC
SHA
INM
D6_D7_P
D6_D7_M
D8_D9_P
D8_D9_M
D10_D11_P
D10_D11_M
VCM
Control
Interface
Reference
D12_D13_P
D12_D13_M
OVR
MODE
OE
DFS
RESET
SEN
SDATA
SCLK
IREF
ADS5545
LVDS MODE
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
PACKAGELEAD
ADS5545
QFN-48 (2)
(1)
(2)
2
PACKAGE
DESIGNATOR
RGZ
SPECIFIED
TEMPERATURE
RANGE
–40°C to 85°C
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA,
QUANTITY
ADS5545IRGZT
Tape and Reel,
250
ADS5545IRGZR
Tape and Reel,
2500
AZ5545
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
For thermal pad size on the package, see the mechanical drawings at the end of this data sheet. θJA = 25.41°C/W (0 LFM air flow),
θJC = 16.5°C/W when used with 2 oz. copper trace and pad soldered directly to a JEDEC standard four layer 3 in x 3 in (7.62 cm x 7.62
cm) PCB.
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VSS
VALUE
UNIT
Supply voltage range, AVDD
–0.3 V to 3.9
V
Supply voltage range, DRVDD
–0.3 V to 3.9
V
Voltage between AGND and DRGND
-0.3 to 0.3
V
Voltage between AVDD to DRVDD
-0.3 to 3.3
V
Voltage applied to VCM pin (in external reference mode)
-0.3 to 1.8
V
–0.3 V to minimum (3.6, AVDD + 0.3 V)
V
Voltage applied to analog input pins, INP and INM
Voltage applied to input clock pins, CLKP and CLKM
TA
Operating free-air temperature range
TJ
Operating junction temperature range
Tstg
Storage temperature range
(1)
-0.3 V to AVDD + 0.3 V
V
–40 to 85
°C
125
°C
–65 to 150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
TYP
MAX
UNIT
Analog supply voltage, AVDD
3
3.3
3.6
V
Digital supply voltage, DRVDD
3
3.3
3.6
V
SUPPLIES
ANALOG INPUTS
Differential input voltage range
2
VPP
1.5 ±0.1
Input common-mode voltage
Voltage applied on VCM in external reference mode
1.45
1.5
V
1.55
V
CLOCK INPUT
Input clock sample rate
(1)
DEFAULT SPEED mode
50
170
1
60
LOW SPEED mode
MSPS
Input clock amplitude differential (V(CLKP) - V(CLKM))
Sine wave, ac-coupled
0.4
1.5
VPP
LVPECL, ac-coupled
1.6
VPP
LVDS, ac-coupled
0.7
VPP
LVCMOS, single-ended, ac-coupled
3.3
V
Input clock duty cycle (See Figure 33)
35%
50%
65%
DIGITAL OUTPUTS
CL
Maximum external load capacitance from each output pin to DRGND (LVDS and CMOS modes)
CMOS mode
5
pF
LVDS mode, without internal termination
(default after reset)
5
pF
(2)
10
pF
LVDS mode, with internal termination
RL
Differential load resistance between the LVDS output pairs (LVDS mode)
Operating free-air temperature
(1)
(2)
Ω
100
–40
85
°C
See section on Low Sampling Frequency Operation for more information
See section on LVDS Buffer Internal Termination for more information
Submit Documentation Feedback
3
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
ELECTRICAL CHARACTERISTICS
Typical values are at 25°C, min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C,
AVDD = DRVDD = 3.3 V, sampling rate = 170 MSPS, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock
duty cycle, –1 dBFS differential analog input, internal reference mode, 0dB gain, DDR LVDS data output (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
RESOLUTION
TYP
MAX
UNIT
14
bits
Differential input voltage range
2
VPP
Differential input capacitance
7
pF
ANALOG INPUT
–3 dB, source impedance 50 Ω
Analog input bandwidth
Analog input common mode current
(per input pin)
500
MHz
280
µA
V
REFERENCE VOLTAGES
V(REFB)
Internal reference bottom voltage
Internal reference mode
0.5
V(REFT)
Internal reference top voltage
Internal reference mode
2.5
∆V(REF)
Internal reference error
V(REFT) - V(REFB)
VCM
Common mode output voltage
Internal reference mode
1.5
V
VCM output current capability
Internal reference mode
±4
mA
-60
± 25
V
60
mV
DC ACCURACY
No Missing Codes
DNL
Differential non-linearity
INL
Integral non-linearity
Assured
Offset error
–0.9
0.5
2.5
LSB
–5
±3
5
LSB
-10
5
10
mV
Offset temperature coefficient
0.002
Gain error due to internal reference error alone
(∆V(REF) / 2.0) %
Gain error excluding internal reference error (1)
Gain temperature coefficient
PSRR
DC Power supply rejection ratio
ppm/°C
-3
±1
3
% FS
-2
±1
2
% FS
0.01
∆%/°C
0.6
mV/V
281
mA
51
mA
mA
POWER SUPPLY
I(AVDD)
I(DRVDD)
Digital supply current
LVDS mode, IO = 3.5 mA,
RL = 100 Ω, CL = 5 pF
ICC
Total supply current
LVDS mode
332
Total power dissipation
LVDS mode
1.1
1.275
Standby power
In STANDBY mode with input clock
stopped
100
150
mW
Clock stop power
With input clock stopped
100
150
mW
(1)
4
Analog supply current
Gain error is specified from design and characterization; it is not tested in production.
Submit Documentation Feedback
W
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
ELECTRICAL CHARACTERISTICS
Typical values are at 25°C, min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C,
AVDD = DRVDD = 3.3 V, sampling rate = 170 MSPS, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock
duty cycle, –1 dBFS differential analog input, internal reference mode, 0dB gain, DDR LVDS data output (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AC CHARACTERISTICS
FIN = 10 MHz
74.3
FIN = 70 MHz
71.5
FIN = 100 MHz
SNR
Signal to noise ratio
FIN = 150 MHz
FIN = 225 MHz
FIN = 300 MHz
RMS output noise
72.8
0 dB gain, 2 VPP FS (1)
71.3
3 dB gain, 1.4 VPP FS
69.8
0 dB gain, 2 VPP FS
Spurious free dynamic range
3 dB gain, 1.4 VPP FS
69
1.1
FIN = 10 MHz
90
77
85
FIN = 150 MHz
84
FIN = 300 MHz
0 dB gain, 2 VPP FS
75
3 dB gain, 1.4 VPP FS
78
0 dB gain, 2 VPP FS
72
3 dB gain, 1.4 VPP FS
75
FIN = 10 MHz
70.5
FIN = 100 MHz
Signal to noise and distortion ratio
FIN = 300 MHz
72.2
0 dB gain, 2 VPP FS
69
3 dB gain, 1.4 VPP FS
68.9
0 dB gain, 2 VPP FS
67.8
3 dB gain, 1.4 VPP FS
67.5
FIN = 10 MHz
77
FIN = 100 MHz
Second harmonic
FIN = 300 MHz
88
0 dB gain, 2 VPP FS
76
3 dB gain, 1.4 VPP FS
79
0 dB gain, 2 VPP FS
73
3 dB gain, 1.4 VPP FS
75
FIN = 10 MHz
Third harmonic
85
85
FIN = 150 MHz
84
FIN = 300 MHz
(1)
77
FIN = 100 MHz
FIN = 225 MHz
dBc
90
FIN = 70 MHz
HD3
90
90
FIN = 150 MHz
FIN = 225 MHz
dBFS
91
FIN = 70 MHz
HD2
73
72.8
FIN = 150 MHz
FIN = 225 MHz
dBc
74.1
FIN = 70 MHz
SINAD
LSB
85
FIN = 100 MHz
FIN = 225 MHz
dBFS
70
Inputs tied to common-mode
FIN = 70 MHz
SFDR
74
73.4
0 dB gain, 2 VPP FS
75
3 dB gain, 1.4 VPP FS
78
0 dB gain, 2 VPP FS
72
3 dB gain, 1.4 VPP FS
75
dBc
FS = Full scale range
Submit Documentation Feedback
5
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
ELECTRICAL CHARACTERISTICS (continued)
Typical values are at 25°C, min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C,
AVDD = DRVDD = 3.3 V, sampling rate = 170 MSPS, sine wave input clock, 1.5 VPP differential clock amplitude, 50% clock
duty cycle, –1 dBFS differential analog input, internal reference mode, 0dB gain, DDR LVDS data output (unless otherwise
noted)
PARAMETER
Worst harmonic (other than HD2, HD3)
TEST CONDITIONS
MIN
93
FIN = 70 MHz
91
FIN = 100 MHz
90
FIN = 150 MHz
89
FIN = 225 MHz
87
FIN = 300 MHz
FIN = 70 MHz
ENOB
IMD
PSRR
6
Total harmonic distortion
Effective number of bits
Two-tone intermodulation distortion
75
dBc
82
83
FIN = 150 MHz
82
FIN = 225 MHz
72
FIN = 300 MHz
68
FIN = 10 MHz
FIN1 = 50.09 MHz, FIN2 = 46.09 MHz, -7 dBFS
each tone
UNIT
86.5
FIN = 100 MHz
FIN = 70 MHz
MAX
87
FIN = 10 MHz
THD
TYP
FIN = 10 MHz
12
11.4
11.8
dBc
bits
92
dBFS
FIN1 = 130.09 MHz, FIN2 = 125.09 MHz, -7 dBFS
each tone
90
AC power supply rejection ratio
30 MHz, 200 mVPP signal on 3.3-V supply
35
dBc
Voltage overload recovery time
Recovery to 1% (of final value) for 6-dB overload
with sine-wave input at Nyquist frequency
1
Clock
cycles
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DIGITAL CHARACTERISTICS
(1)
The DC specifications refer to the condition where the digital outputs are not switching, but are permanently at a valid logic
level 0 or 1 AVDD = DRVDD = 3.3 V, IO = 3.5 mA, RL = 100 Ω (2)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DIGITAL INPUTS
High-level input voltage
2.4
V
Low-level input voltage
0.8
V
High-level input current
33
µA
Low-level input current
–33
µA
4
pF
High-level output voltage
3.3
V
Low-level output voltage
0
V
2
pF
1375
mV
1025
mV
350
mV
1200
mV
2
pF
Input capacitance
DIGITAL OUTPUTS – CMOS MODE
Output capacitance
Output capacitance inside the device, from each output to
ground
DIGITAL OUTPUTS – LVDS MODE
High-level output voltage
Low-level output voltage
Output differential voltage, |VOD|
225
VOS Output offset voltage, single-ended
Common-mode voltage of OUTP and OUTM
Output capacitance
Output capacitance inside the device, from either output to
ground
(1)
(2)
All LVDS and CMOS specifications are characterized, but not tested at production.
IO refers to the LVDS buffer current setting, RL is the differential load resistance between the LVDS output pair.
TIMING CHARACTERISTICS – LVDS AND CMOS MODES (1)
Typical values are at 25°C, min and max values are across the full temperature range TMIN = –40°C to TMAX = 85°C, AVDD =
DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP clock amplitude, CL = 5 pF (2), IO = 3.5 mA,
RL = 100 Ω (3), no internal termination, unless otherwise noted.
For timings at lower sampling frequencies, see the Output Timing section in the APPLICATION INFORMATION of this data
sheet.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ta
Aperture delay
1.2
ns
tj
Aperture jitter
150
fs rms
Wake-up time
Time to valid data after coming out of
STANDBY mode
100
Time to valid data after stopping and restarting
the input clock
100
Latency
(1)
(2)
(3)
µs
14
clock
cycles
Timing parameters are specified by design and characterization and not tested in production.
CL is the effective external single-ended load capacitance between each output pin and ground.
IO refers to the LVDS buffer current setting; RL is the differential load resistance between the LVDS output pair.
Submit Documentation Feedback
7
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TIMING CHARACTERISTICS – LVDS AND CMOS MODES (continued)
For timings at lower sampling frequencies, see the Output Timing section in the APPLICATION INFORMATION of this data
sheet.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DDR LVDS MODE (4)
Data setup time (5)
tsu
time (5)
Data valid
(6)
1.3
1.8
ns
Zero-cross of CLKOUTP to data becoming
invalid (6)
to zero-cross of CLKOUTP
0.5
1.0
ns
3.9
4.6
5.3
45%
50%
55%
th
Data hold
tPDI
Clock propagation delay
Input clock rising edge zero-cross to output
clock rising edge zero-cross
LVDS bit clock duty cycle
Duty cycle of differential clock,
(CLKOUTP-CLKOUTM)
80 ≤ Fs ≤ 170 MSPS
tr,
tf
Data rise time,
Data fall time
Rise time measured from –50 mV to 50 mV
Fall time measured from 50 mV to –50 mV
1 ≤ Fs ≤ 170 MSPS
50
100
200
ps
tCLKFALL,
tCLKRISE
Output clock fall time,
Output clock rise time
Rise time measured from –50 mV to 50 mV
Fall time measured from 50 mV to –50 mV
1 ≤ Fs ≤ 170 MSPS
50
100
200
ps
tOE
Output enable (OE) to valid data
delay
1
µs
Time to valid data after OE becomes active
ns
PARALLEL CMOS MODE
Data valid (8) to 50% of CLKOUT rising edge
2.5
3.3
ns
50% of CLKOUT rising edge to data becoming
invalid (8)
0.8
1.2
ns
Clock propagation delay (9)
Input clock rising edge zero-cross to 50% of
CLKOUT rising edge
1.9
2.7
Output clock duty cycle
Duty cycle of output clock (CLKOUT)
80 ≤ Fs ≤ 170 MSPS
Data rise time,
Data fall time
Rise time measured from 20% to 80% of
DRVDD
Fall time measured from 80% to 20% of
DRVDD
1 ≤ Fs ≤ 170 MSPS
0.8
tCLKRISE,
tCLKFALL
Output clock rise time,
Output clock fall time
Rise time measured from 20% to 80% of
DRVDD
Fall time measured from 80% to 20% of
DRVDD
1 ≤ Fs ≤ 170 MSPS
0.4
tOE
Output enable (OE) to valid data
delay
Time to valid data after OE becomes active
tsu
Data setup time
th
Data hold time
tPDI
tr,
tf
(4)
(5)
(6)
(7)
(8)
(9)
8
(5) (7)
(5) (7)
3.5
ns
1.5
2
ns
0.8
1.2
ns
50
ns
45%
Measurements are done with a transmission line of 100 Ω characteristic impedance between the device and the load.
Setup and hold time specifications take into account the effect of jitter on the output data and clock. These specifications also assume
that the data and clock paths are perfectly matched within the receiver. Any mismatch in these paths within the receiver would appear
as reduced timing margin.
Data valid refers to logic high of 50 mV and logic low of –50 mV.
Setup and hold times are specified with default output clock and data positions. For other positions, the timing numbers have to be
adjusted appropriately.
Data valid refers to logic high of 2 V and logic low of 0.8 V
Clock propagation delay timings are specified with default output clock positions. For other positions, the timing numbers have to be
adjusted appropriately.
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
N+4
N+3
N+2
N+1
Sample
N
N+17
N+16
N+15
N+14
Input
Signal
ta
Input
Clock
CLKP
CLKM
CLKOUTM
CLKOUTP
tsu
Output Data
DXP, DXM
E
E
O
E – Even Bits D0,D2,D4,D6,D8,D10,D12
O – Odd Bits D1,D3,D5,D7,D9,D11,D13
O
N–14
E
O
N–13
E
E
O
N–12
tPDI
th
14 Clock Cycles
DDR
LVDS
E
O
N–11
E
O
N–10
O
E
O
N
N–1
E
E
O
O
N+2
N+1
tPDI
CLKOUT
tsu
Parallel
CMOS
14 Clock Cycles
Output Data
D0–D13
N–13
N–14
N–12
th
N–11
N–10
N
N–1
N+1
N+2
Figure 1. Latency
Input
Clock
CLKM
CLKP
tPDI
Output
Clock
CLKOUTP
CLKOUTM
tsu
th
tsu
Output
Data Pair
(1)
(2)
Dn
Dn_Dn+1_P,
Dn_Dn+1_M
th
Dn
(1)
Dn+1
(2)
– Bits D0, D2, D4, D6, D8, D10, D12
Dn+1 – Bits D1, D3, D5, D7, D9, D11, D13
T0106-01
Figure 2. LVDS Mode Timing
Submit Documentation Feedback
9
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
CLKM
Input
Clock
CLKP
tPDI
Output
Clock
CLKOUT
th
tsu
Output
Data
Dn
Dn
(1)
(1)
Dn – Bits D0–D13
T0107-01
Figure 3. CMOS Mode Timing
10
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DEVICE PROGRAMMING MODES
ADS5545 offers flexibility with several programmable features that are easily configured.
The device can be configured independently using either a parallel interface control or a serial interface
programming.
In addition, the device supports a third configuration mode, where both the parallel interface and the serial
control registers are used. In this mode, the priority between the parallel and serial interfaces is determined by a
priority table (Table 2). If this additional level of flexibility is not required, the user can select either the serial
interface programming or the parallel interface control.
USING PARALLEL INTERFACE CONTROL ONLY
To control the device using parallel interface, keep RESET tied to high (DRVDD). Pins DFS, MODE, SEN,
SCLK, and SDATA are used to directly control certain modes of the ADC. The device is configured by
connecting the parallel pins to the correct voltage levels (as described in Table 3 to Table 7). The voltage levels
can be derived by using a resistor string as illustrated in Figure 4. There is no need to apply reset.
In this mode, SEN, SCLK, and SDATA function as parallel interface control pins. Frequently used functions are
controlled in this mode—standby, selection between LVDS/CMOS output format, internal/external reference,
two's complement/straight binary output format, and position of the output clock edge.
Table 1 has a description of the modes controlled by the four parallel pins.
Table 1. Parallel Pin Definition
PIN
DFS
MODE
CONTROL MODES
DATA FORMAT and the LVDS/CMOS output interface
Internal or external reference
SEN
CLKOUT edge programmability
SCLK
LOW SPEED mode control for low sampling frequencies (< 50 MSPS)
SDATA
STANDBY mode – Global (ADC, internal references and output buffers are powered down)
USING SERIAL INTERFACE PROGRAMMING ONLY
To program using the serial interface, the internal registers must first be reset to their default values, and the
RESET pin must be kept low. In this mode, SEN, SDATA, and SCLK function as serial interface pins and are
used to access the internal registers of ADC. The registers are reset either by applying a pulse on the RESET
pin, or by a high setting on the <RST> bit (D1 in register 0x6C). The serial interface section describes the
register programming and register reset in more detail.
Since the parallel pins DFS and MODE are not used in this mode, they must be tied to ground.
USING BOTH THE SERIAL INTERFACE AND PARALLEL CONTROLS
For increased flexibility, a combination of serial interface registers and parallel pin controls (DFS, MODE) are
used to configure the device.
The serial registers must first be reset to their default values, and the RESET pin must be kept low. In this
mode, SEN, SDATA, and SCLK function as serial interface pins and are used to access the internal registers of
ADC. The registers are reset either by applying a pulse on RESET pin or by a high setting on the <RST> bit (D1
in register 0x6C). The serial interface section describes the register programming and register reset in more
detail.
The parallel interface control pins DFS and MODE are used, and their function is determined by the appropriate
voltage levels as described in Table 6 and Table 7. The voltage levels are derived by using a resistor string as
illustrated in Figure 4. Since some functions are controlled using both the parallel pins and serial registers, the
priority between the two is determined by a priority table (Table 2).
Submit Documentation Feedback
11
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Table 2. Priority Between Parallel Pins and Serial Registers
PIN
MODE
DFS
FUNCTIONS SUPPORTED
PRIORITY
Internal/External reference
When using the serial interface, bit <REF> (register 0x6D, bit D4) controls this mode, ONLY
if the MODE pin is tied low.
DATA FORMAT
When using the serial interface, bit <DF> (register 0x63, bit D3) controls this mode, ONLY if
the DFS pin is tied low.
LVDS/CMOS
When using the serial interface, bit <ODI> (register 0x6C, bits D3-D4) controls LVDS/CMOS
selection independent of the state of DFS pin
AVDD
(2/3) AVDD
R
(2/3) AVDD
GND
R
AVDD
(1/3) AVDD
(1/3) AVDD
R
To Parallel Pin
Figure 4. Simple Scheme to Configure Parallel Pins
12
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DESCRIPTION OF PARALLEL PINS
Table 3. SCLK Control Pin
SCLK (Pin 29)
0
DRVDD
DESCRIPTION
DEFAULT SPEED - Must be used for sampling frequencies > 50 MSPS.
LOW SPEED - Must be used for sampling frequencies ≤ 50 MSPS.
Table 4. SDATA Control Pin
SDATA (Pin 28)
0
DRVDD
DESCRIPTION
Normal operation (Default)
STANDBY. This is a global power down, where ADC, internal references and the output buffers are powered down.
Table 5. SEN Control Pin
SEN (Pin 27)
CMOS mode: CLKOUT edge later by (3/12)Ts
(1);
LVDS mode: CLKOUT edge aligned with data transition
(1/3)DRVDD
CMOS mode: CLKOUT edge later by (2/12)Ts
(1);
LVDS mode: CLKOUT edge aligned with data transition
(2/3)DRVDD
CMOS mode: CLKOUT edge later by (1/12)Ts
(1);
LVDS mode: CLKOUT edge earlier by (1/12)Ts
DRVDD
(1)
DESCRIPTION
0
(1)
Default CLKOUT position
Ts = 1/Sampling Frequency
Table 6. DFS Control Pin
DFS (Pin 6)
0
DESCRIPTION
2's complement data and DDR LVDS output (Default)
(1/3)DRVDD
2's complement data and parallel CMOS output
(2/3)DRVDD
Offset binary data and parallel CMOS output
DRVDD
Offset binary data and DDR LVDS output
Table 7. MODE Control Pin
MODE (Pin 23)
DESCRIPTION
0
Internal reference
(1/3)AVDD
External reference
(2/3)AVDD
External reference
AVDD
Internal reference
SERIAL INTERFACE
The ADC has a set of internal registers, which can be accessed through the serial interface formed by pins SEN
(Serial interface Enable), SCLK (Serial Interface Clock), SDATA (Serial Interface Data) and RESET. After device
power-up, the internal registers must be reset to their default values by applying a high-going pulse on RESET
(of width greater than 10 ns).
Serial shift of bits into the device is enabled when SEN is low. Serial data SDATA is latched at every falling edge
of SCLK when SEN is active (low). The serial data is loaded into the register at every 16th SCLK falling edge
when SEN is low. If the word length exceeds a multiple of 16 bits, the excess bits are ignored. Data is loaded in
multiples of 16-bit words within a single active SEN pulse.
The first 8 bits form the register address and the remaining 8 bits form the register data. The interface can work
with SCLK frequency from 20 MHz down to very low speeds (few Hertz) and also with non-50% SCLK duty
cycle.
Submit Documentation Feedback
13
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
REGISTER INITIALIZATION
After power-up, the internal registers must be reset to their default values. This is done in one of two ways:
1. Either through hardware reset by applying a high-going pulse on RESET pin (of width greater than 10 ns)
as shown in Figure 5.
OR
2. By applying software reset. Using the serial interface, set the <RST> bit (D1 in register 0x6C) to high.
This initializes the internal registers to their default values and then self-resets the <RST> bit to low. In
this case the RESET pin is kept low.
Register Address
SDATA
A7
A6
A5
A4
A3
A2
Register Data
A1
A0
D7
t(SCLK)
D6
D5
D4
D3
D2
D1
D0
t(DH)
t(DSU)
SCLK
t(SLOADH)
t(SLOADS)
SEN
RESET
T0109-01
Figure 5. Serial Interface Timing Diagram
14
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
SERIAL INTERFACE TIMING CHARACTERISTICS
Typical values at 25°C, min and max values across the full temperature range TMIN = –40°C to TMAX = 85°C,
AVDD = DRVDD = 3.3 V (unless otherwise noted)
MIN
TYP
> DC
MAX
UNIT
20
MHz
fSCLK
SCLK frequency
tSLOADS
SEN to SCLK setup time
25
ns
tSLOADH
SCLK to SEN hold time
25
ns
tDSU
SDATA setup time
25
ns
tDH
SDATA hold time
25
ns
RESET TIMING
Typical values at 25°C, min and max values across the full temperature range TMIN = –40°C to TMAX = 85°C,
AVDD = DRVDD = 3.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
t1
Power-on delay
Delay from power-up of AVDD and DRVDD to RESET pulse active
MIN
t2
Reset pulse width
t3
tPO
TYP
MAX
UNIT
5
ms
Pulse width of active RESET signal
10
ns
Register write delay
Delay from RESET disable to SEN active
25
Power-up time
Delay from power-up of AVDD and DRVDD to output stable
ns
6.5
ms
Power Supply
AVDD, DRVDD
t1
RESET
t2
t3
SEN
T0108-01
NOTE: A high-going pulse on RESET pin is required in serial interface mode in case of initialization through hardware reset.
For parallel interface operation, RESET has to be tied permanently HIGH.
Figure 6. Reset Timing Diagram
Submit Documentation Feedback
15
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
SERIAL REGISTER MAP
Table 8 gives a snapshot of all the functions that can be programmed through the serial interface.
Table 8. Summary of Functions Supported by Serial Interface
REGISTER
ADDRESS
IN HEX
A7 - A0
REGISTER FUNCTIONS
D7
65
D6
D5
D4
<DATA POSN>
OUTPUT DATA
POSITION
PROGRAMMABILITY
62
63
D3
<LOW SPEED>
ENABLE LOW
SAMPLING
FREQUENCY
OPERATION
<STBY>
GLOBAL
POWER
DOWN
D1
<DF>
DATA FORMAT 2's COMP or
STRAIGHT
BINARY
<GAIN> GAIN PROGRAMMING <GAIN> - 1 dB to 6 dB
<CUSTOM A> CUSTOM PATTERN (D7 TO D0)
6A
<CUSTOM B> CUSTOM PATTERN (D13 TO D8)
6B
<CLKIN GAIN> INPUT CLOCK BUFFER GAIN PROGRAMMABILITY
<ODI> OUTPUT DATA INTERFACE
- DDR LVDS or PARALLEL CMOS
6C
6D
<SCALING> POWER SCALING
7E
<DATA TERM>
INTERNAL TERMINATION – DATA
OUTPUTS
7F
D0
<TEST PATTERN> – ALL 0S, ALL 1s,
TOGGLE, RAMP, CUSTOM PATTERN
69
16
D2
<CLKOUT POSN>
OUTPUT CLOCK POSITION PROGRAMMABILITY
68
(1)
(2)
(1) (2)
<RST>
SOFTWARE
RESET
<REF>
INTERNAL or
EXTERNAL
REFERENCE
<CLKOUT TERM>
INTERNAL TERMINATION – OUTPUT CLOCK
<CURR DOUBLE>
LVDS CURRENT
DOUBLE
The unused bits in each register (shown by blank cells in above table) must be programmed as ‘0’.
Multiple functions in a register can be programmed in a single write operation.
Submit Documentation Feedback
<LVDS CURR>
LVDS CURRENT
PROGRAMMABILITY
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DESCRIPTION OF SERIAL REGISTERS
Each register function is explained in detail below.
Table 9. Serial Register A
A7 - A0 (hex)
62
D7
D6
D5
<DATA POSN>
OUTPUT DATA
POSITION
PROGRAMMABILITY
D4
D3
D2
D1
D0
<CLKOUT POSN>
OUTPUT CLOCK POSITION PROGRAMMABILITY
D4 - D0
<CLKOUT POSN> Output clock position programmability
00001
Default CLKOUT position after reset. Setup/hold timings with this clock
position are specified in the timing characteristics table.
XX011
CMOS – Rising edge later by (1/12) Ts
LVDS – Rising edge earlier by (1/12) Ts
XX101
CMOS – Rising edge later by (3/12) Ts
LVDS – Rising edge aligned with data transition
XX111
CMOS – Rising edge later by (2/12) Ts
LVDS – Rising edge aligned with data transition
01XX1
CMOS – Rising edge later by (1/12) Ts
LVDS – Rising edge earlier by (1/12) Ts
10XX1
CMOS – Rising edge later by (3/12) Ts
LVDS – Rising edge aligned with data transition
11XX1
CMOS – Rising edge later by (2/12) Ts
LVDS – Rising edge aligned with data transition
D6 – D5
<DATA POSN> Output data position programmability (Only in
CMOS mode)
00
Data Position 1 - Default output data position after reset. Setup/hold
timings with this data position are specified in the timing
characteristics table.
01
Data Position 2 - Setup time increases by (2/36) Ts
10
Data Position 3 - Setup time increases by (5/36) Ts
11
Data Position 4 - Setup time decreases by (6/36) Ts
Submit Documentation Feedback
17
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Table 10. Serial Register B
A7 - A0 (hex)
63
D7
D6
D5
<STBY>
GLOBAL
POWER
DOWN
D4
D3
<LOW SPEED>
ENABLE LOW
SAMPLING
FREQUENCY
OPERATION
<DF>
DATA
FORMAT
2's COMP or
STRAIGHT
BINARY
D2
D3
<DF> Output data format
0
2's complement
1
Straight binary
D4
<LOW SPEED> Low sampling frequency operation
0
Default SPEED mode for 50 < Fs ≤ 190 MSPS
1
Low SPEED mode 1≤ Fs ≤ 50 MSPS
D7
<STBY> Global power down
0
Normal operation
1
Global power down (includes ADC, internal references and output buffers)
D1
D0
Table 11. Serial Register C
A7 - A0 (hex)
65
D7
D6
D5
D4
D3
D2
<TEST PATTERNS>— ALL 0S, ALL 1s,
TOGGLE, RAMP, CUSTOM PATTERN
D7 - D5
<TEST PATTERN> Outputs selected test pattern on data lines
000
Normal operation
001
All 0s
010
All 1s
011
Toggle pattern – alternate 1s and 0s on each data output and across
data outputs
100
Ramp pattern – Output data ramps from 0x0000 to 0x3FFF by one
code every clock cycle
101
Custom pattern – Outputs the custom pattern in CUSTOM PATTERN
registers A and B
111
Unused
18
Submit Documentation Feedback
D1
D0
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Table 12. Serial Register D
A7 - A0 (hex)
D7
D6
D5
D4
D3
68
D2
D1
D0
<GAIN> GAIN PROGRAMMING <GAIN> - 1 dB to 6 dB
D3 - D0
<GAIN> Gain programmability
1000
0 dB gain, default after reset
1001
1 dB
1010
2 dB
1011
3 dB
1100
4 dB
1101
5 dB
1110
6 dB
Table 13. Serial Register E
A7 - A0 (hex)
D7
D6
D5
69
D4
D3
D2
D1
D0
<CUSTOM A> CUSTOM PATTERN (D7 TO D0)
6A
<CUSTOM B> CUSTOM PATTERN (D13 TO D8)
Reg 69
D7 – D0
Program bits D7 to D0 of custom pattern
Reg 6A
D5 – D0
Program bits D13 to D8 of custom pattern
Table 14. Serial Register F
A7 - A0 (hex)
D7
D6
D5
6B
D4
D3
D2
D1
D0
<CLKIN GAIN> INPUT CLOCK BUFFER GAIN PROGRAMMABILITY
D5 - D0
<CLKIN GAIN> Input clock buffer gain programming
110010
Gain 4, maximum gain
101010
Gain 3
100110
Gain 2
100000
Gain1, default after reset
100011
Gain 0 minimum gain
Submit Documentation Feedback
19
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Table 15. Serial Register G
A7 - A0 (hex)
D7
D6
D5
D4
D3
D2
<ODI> OUTPUT DATA
INTERFACE - DDR LVDS OR
PARALLEL CMOS
6C
D1
<RST> Software resets the ADC
1
Resets all registers to default values
D4 - D3
<ODI> Output data interface
00
DDR LVDS outputs, default after reset
01
DDR LVDS outputs
11
Parallel CMOS outputs
D1
D0
<RST>
SOFTWARE
RESET
Table 16. Serial Register H
A7 - A0
6D
D7
D6
D5
<SCALING> POWER SCALING
D4
D3
D2
D1
D0
D1
D0
<REF> INTERNAL or
EXTERNAL REFERENCE
D4
<REF> Reference
0
Internal reference
1
External reference mode, force voltage on Vcm to set reference.
D7 - D5
<SCALING> Program power scaling at lower sampling
frequencies
001
Use for Fs > 150 MSPS, default after reset
011
Power Mode 1, use for 105 < Fs ≤ 150 MSPS
101
Power Mode 2, use for 50 < Fs ≤ 105
111
Power Mode 3, use for Fs ≤ 50 MSPS
Table 17. Serial Register I
A7 - A0
7E
D7
D6
D5
<DATA TERM> INTERNAL TERMINATION –
DATA OUTPUTS
D4
D2
<CLKOUT TERM> INTERNAL
TERMINATION – OUTPUT CLOCK
D1 - D0
<LVDS CURR> LVDS buffer current programming
00
3.5 mA, default
01
2.5 mA
10
4.5 mA
11
1.75 mA
20
D3
Submit Documentation Feedback
<LVDS CURR> LVDS
CURRENT
PROGRAMMABILITY
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
D4 - D2
<CLKOUT TERM> Program internal termination for
output clock (CLKOUT pin) buffer
000
No internal termination
001
325
010
200
011
125
100
170
101
120
110
100
111
75
D7 - D5
<DATA TERM> Program internal termination for data
buffers
000
No internal termination
001
325
010
200
011
125
100
170
101
120
110
100
111
75
Table 18. Serial Register J
A7 - A0
7F
D7
D6
D5
D4
D3
D2
D1
D0
<CURR DOUBLE> LVDS
CURRENT DOUBLE
D7 - D6
<CURR DOUBLE> LVDS buffer current doubling
00
Value specified by <LVDS CURR>
01
2x data, 2x clockout currents
10
1x data, 2x clockout currents
11
2x data, 4x clockout currents
Submit Documentation Feedback
21
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
PIN CONFIGURATION (LVDS MODE)
37 D2_D3_M
38 D2_D3_P
39 D4_D5_M
40 D4_D5_P
41 D6_D7_M
42 D6_D7_P
43 D8_D9_M
44 D8_D9_P
45 D10_D11_M
46 D10_D11_P
47 D12_D13_M
48 D12_D13_P
RGZ PACKAGE
(TOP VIEW)
DRGND 1
36 DRGND
DRVDD 2
35 DRVDD
Thermal Pad
OVR 3
34 D0_D1_P
CLKOUTM 4
33 D0_D1_M
CLKOUTP 5
32 NC
DFS 6
31 NC
OE 7
30 RESET
AVDD 8
29 SCLK
AGND 9
28 SDATA
AVDD 24
MODE 23
AVDD 22
IREF 21
AVDD 20
AGND 19
AVDD 18
25 AGND
AGND 17
AGND 12
INM 16
26 AVDD
INP 15
CLKM 11
AGND 14
27 SEN
VCM 13
CLKP 10
Figure 7. LVDS Mode Pinout
PIN ASSIGNMENTS – LVDS Mode
PIN NAME
DESCRIPTION
PIN
TYPE
PIN
NUMBER
NUMBER
OF PINS
AVDD
Analog power supply
I
8, 18, 20,
22, 24, 26
6
AGND
Analog ground
I
9, 12, 14,
17, 19, 25
6
CLKP, CLKM
Differential clock input
I
10, 11
2
INP, INM
Differential analog input
I
15, 16
2
VCM
Internal reference mode – Common-mode voltage output.
External reference mode – Reference input. The voltage forced on this pin sets
the internal references.
I/O
13
1
IREF
Current-set resistor, 56.2-kΩ resistor to ground.
I
21
1
RESET
Serial interface RESET input.
When using the serial interface mode, the user MUST initialize internal registers
through hardware RESET by applying a high-going pulse on this pin, or by using
the software reset option. See the SERIAL INTERFACE section.
In parallel interface mode, the user has to tie the RESET pin permanently HIGH.
(SDATA and SEN are used as parallel pin controls in this mode)
The pin has an internal 100-kΩ pull-down resistor.
I
30
1
22
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
PIN CONFIGURATION (LVDS MODE) (continued)
PIN ASSIGNMENTS – LVDS Mode (continued)
PIN
TYPE
PIN
NUMBER
NUMBER
OF PINS
I
29
1
I
28
1
SEN
This pin functions as serial interface enable input when RESET is low. It functions
as CLKOUT edge programmability when RESET is tied high. See Table 5 for
detailed information.
The pin has an internal 100-kΩ pull-up resistor to DRVDD.
I
27
1
OE
Output buffer enable input, active high. The pin has an internal 100-kΩ pull-up
resistor to DRVDD.
I
7
1
DFS
Data Format Select input. This pin sets the DATA FORMAT (Twos complement or
Offset binary) and the LVDS/CMOS output mode type. See Table 6 for detailed
information.
I
6
1
MODE
Mode select input. This pin selects the Internal or External reference mode. See
Table 7 for detailed information.
I
23
1
CLKOUTP
Differential output clock, true
O
5
1
CLKOUTM
Differential output clock, complement
O
4
1
D0_D1_P
Differential output data D0 and D1 multiplexed, true
O
34
1
D0_D1_M
Differential output data D0 and D1 multiplexed, complement.
O
33
1
D2_D3_P
Differential output data D2 and D3 multiplexed, true
O
38
1
D2_D3_M
Differential output data D2 and D3 multiplexed, complement
O
37
1
D4_D5_P
Differential output data D4 and D5 multiplexed, true
O
40
1
D4_D5_M
Differential output data D4 and D5 multiplexed, complement
O
39
1
D6_D7_P
Differential output data D6 and D7 multiplexed, true
O
42
1
D6_D7_M
Differential output data D6 and D7 multiplexed, complement
O
41
1
D8_D9_P
Differential output data D8 and D9 multiplexed, true
O
44
1
D8_D9_M
Differential output data D8 and D9 multiplexed, complement
O
43
1
D10_D11_P
Differential output data D10 and D11 multiplexed, true
O
46
1
D10_D11_M
Differential output data D10 and D11 multiplexed, complement
O
45
1
D12_D13_P
Differential output data D12 and D13 multiplexed, true
O
48
1
D12_D13_M
Differential output data D12 and D13 multiplexed, complement
O
47
1
OVR
Out-of-range indicator, CMOS level signal
O
3
1
DRVDD
Digital and output buffer supply
I
2, 35
2
DRGND
Digital and output buffer ground
I
1, 36
2
NC
Do not connect
31, 32
2
PAD
For best thermal performance, solder the pad to the ground plane on the board
using multiple vias. See Board Design Considerations for details.
0
1
PIN NAME
SCLK
DESCRIPTION
This pin functions as serial interface clock input when RESET is low.
It functions as LOW SPEED control pin when RESET is tied high. Tie SCLK to
LOW for Fs > 50 MSPS and SCLK to HIGH for Fs ≤ 50 MSPS. See Table 3.
The pin has an internal 100-kΩ pull-down resistor.
This pin functions as serial interface data input when RESET is low. It functions
as STANDBY control pin when RESET is tied high.
SDATA
See Table 4 for detailed information.
The pin has an internal 100 kΩ pull-down resistor.
Submit Documentation Feedback
23
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
PIN CONFIGURATION (CMOS MODE)
37 D2
38 D3
39 D4
40 D5
41 D6
42 D7
43 D8
44 D9
45 D10
46 D11
47 D12
48 D13
RGZ PACKAGE
(TOP VIEW)
DRGND 1
36 DRGND
DRVDD 2
35 DRVDD
Thermal Pad
OVR 3
34 D1
UNUSED 4
33 D0
CLKOUT 5
32 NC
DFS 6
31 NC
OE 7
30 RESET
AVDD 8
29 SCLK
AGND 9
28 SDATA
AVDD 24
MODE 23
AVDD 22
IREF 21
AVDD 20
AGND 19
AVDD 18
25 AGND
AGND 17
AGND 12
INM 16
26 AVDD
INP 15
CLKM 11
AGND 14
27 SEN
VCM 13
CLKP 10
Figure 8. CMOS Mode Pinout
PIN ASSIGNMENTS – CMOS Mode
PIN NAME
DESCRIPTION
PIN
TYPE
PIN
NUMBER
NUMBER
OF PINS
AVDD
Analog power supply
I
8, 18, 20,
22, 24, 26
6
AGND
Analog ground
I
9, 12, 14, 17,
19, 25
6
CLKP, CLKM Differential clock input
I
10, 11
2
INP, INM
Differential analog input
I
15, 16
2
VCM
Internal reference mode – Common-mode voltage output.
External reference mode – Reference input. The voltage forced on this pin sets
the internal references.
I/O
13
1
IREF
Current-set resistor, 56.2-kΩ resistor to ground.
I
21
1
I
30
1
I
29
1
Serial interface RESET input.
RESET
When using the serial interface mode, the user MUST initialize internal registers
through hardware RESET by applying a high-going pulse on this pin, or by using
the software reset option. See the SERIAL INTERFACE section.
In parallel interface mode, the user has to tie RESET pin permanently HIGH.
(SDATA and SEN are used as parallel pin controls in this mode).
The pin has an internal 100-kΩ pull-down resistor.
SCLK
24
This pin functions as serial interface clock input when RESET is low.
It functions as LOW SPEED control pin when RESET is tied high. Tie SCLK to
LOW for Fs > 50 MSPS and SCLK to HIGH for Fs ≤ 50 MSPS. See Table 3.
The pin has an internal 100-kΩ pull-down resistor.
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
PIN CONFIGURATION (CMOS MODE) (continued)
PIN ASSIGNMENTS – CMOS Mode (continued)
PIN NAME
DESCRIPTION
PIN
TYPE
PIN
NUMBER
NUMBER
OF PINS
I
28
1
I
27
1
This pin functions as serial interface data input when RESET is low. It functions as
STANDBY control pin when RESET is tied high.
SDATA
See Table 4 for detailed information.
The pin has an internal 100 kΩ pull-down resistor.
SEN
This pin functions as serial interface enable input when RESET is low. It functions
as CLKOUT edge programmability when RESET is tied high. See Table 5 for
detailed information.
The pin has an internal 100-kΩ pull-up resistor to DRVDD.
OE
Output buffer enable input, active high. The pin has an internal 100-kΩ pull-up
resistor to DRVDD.
I
7
1
DFS
Data Format Select input. This pin sets the DATA FORMAT (Twos complement or
Offset binary) and the LVDS/CMOS output mode type. See Table 6 for detailed
information.
I
6
1
MODE
Mode select input. This pin selects the internal or external reference mode. See
Table 7 for detailed information.
I
23
1
CLKOUT
CMOS output clock
O
5
1
D0
CMOS output data D0
O
33
1
D0
CMOS output data D1
O
34
1
D2
CMOS output data D2
O
37
1
D2
CMOS output data D3
O
38
1
D4
CMOS output data D4
O
39
1
D4
CMOS output data D5
O
40
1
D6
CMOS output data D6
O
41
1
D7
CMOS output data D7
O
42
1
D8
CMOS output data D8
O
43
1
D9
CMOS output data D9
O
44
1
D10
CMOS output data D10
O
45
1
D11
CMOS output data D11
O
46
1
D12
CMOS output data D12
O
47
1
D13
CMOS output data D13
O
48
1
OVR
Out-of-range indicator, CMOS level signal
O
3
1
DRVDD
Digital and output buffer supply
I
2, 35
2
DRGND
Digital and output buffer ground
I
1, 36
2
UNUSED
Unused pin in CMOS mode
4
1
NC
Do not connect
31, 32
2
PAD
For best thermal performance, solder the pad to the ground plane on the board
using multiple vias. See Board Design Considerations for details.
0
1
Submit Documentation Feedback
25
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
FFT for 10 MHz INPUT SIGNAL
FFT for 40 MHz INPUT SIGNAL
0
0
SFDR = 90.34 dBc,
SNR = 74.35 dBFS,
SINAD = 74.06 dBFS
-40
SFDR = 88.05 dBc,
SNR = 74.23 dBFS,
SINAD = 73.80 dBFS
-20
Amplitude - dB
Amplitude - dB
-20
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
10
20
f - Frequency - MHz
30
FFT for 70 MHz INPUT SIGNAL
70
80
70
80
FFT for 100 MHz INPUT SIGNAL
0
SFDR = 84.57 dBc,
SNR = 73.87 dBFS,
SINAD = 73.20 dBFS
-20
SFDR = 88.97 dBc,
SNR = 73.52 dBFS,
SINAD = 73.19 dBFS
-20
-40
Amplitude - dB
Amplitude - dB
60
Figure 10.
0
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
10
20
f - Frequency - MHz
30
40
50
60
f - Frequency - MHz
Figure 11.
Figure 12.
FFT for 130 MHz INPUT SIGNAL
FFT for 150 MHz INPUT SIGNAL
0
0
SFDR = 87.85 dBc,
SNR = 73.00 dBFS,
SINAD = 72.68 dBFS
-20
-40
SFDR = 88.60 dBc,
SNR = 72.37 dBFS,
SINAD = 72.09 dBFS
-20
Amplitude - dB
Amplitude - dB
50
f - Frequency - MHz
Figure 9.
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
f - Frequency - MHz
10
20
30
40
50
60
f - Frequency - MHz
Figure 13.
26
40
Figure 14.
Submit Documentation Feedback
70
80
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
FFT for 200 MHz INPUT SIGNAL
FFT for 230 MHz INPUT SIGNAL
0
0
SFDR = 77.26 dBc,
SNR = 71.73 dBFS,
SINAD = 69.73 dBFS
-40
SFDR = 74.64 dBc,
SNR = 71.22 dBFS,
SINAD = 68.06 dBFS
-20
Amplitude - dB
Amplitude - dB
-20
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
10
20
f - Frequency - MHz
50
60
Figure 15.
Figure 16.
FFT for 300 MHz INPUT SIGNAL
FFT for 375 MHz INPUT SIGNAL
0
SFDR = 69.70 dBc,
SNR = 70.12 dBFS,
SINAD = 64.89 dBFS
-20
70
80
SFDR = 63.10 dBc,
SNR = 68.38 dBFS,
SINAD = 60.18 dBFS
-20
-40
Amplitude - dB
Amplitude - dB
40
f - Frequency - MHz
0
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
10
20
f - Frequency - MHz
30
40
50
60
70
80
f - Frequency - MHz
Figure 17.
Figure 18.
FFT for 500 MHz INPUT SIGNAL
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
0
0
SFDR = 59.23 dBc,
SNR = 66.29 dBFS,
SINAD = 56.60 dBFS
-20
FIN1 = 50.09 MHz, -7 dBFS,
FIN2 = 46.09 MHz, -7 dBFS,
2-Tone IMD, 92 dBFS
-20
-40
Amplitude - dB
Amplitude - dB
30
-60
-80
-100
-120
-40
-60
-80
-100
-120
-140
-140
0
10
20
30
40
50
60
70
80
0
f - Frequency - MHz
10
20
30
40
50
60
70
80
f - Frequency - MHz
Figure 19.
Figure 20.
Submit Documentation Feedback
27
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
INTERMODULATION DISTORTION (IMD) vs FREQUENCY
SFDR vs INPUT FREQUENCY
94
0
FIN1 = 130.09 MHz, -7 dBFS,
FIN2 = 125.09 MHz, -7 dBFS,
2-Tone IMD, 90 dBFS
90
86
-40
SFDR - dBc
Amplitude - dB
-20
-60
-80
-100
82
78
74
70
66
-120
62
-140
58
0
10
20
30
40
50
60
70
0
80
50
100 150 200 250 300 350 400 450 500
fIN - Input Frequency - MHz
f - Frequency - MHz
Figure 21.
Figure 22.
SNR vs INPUT FREQUENCY
SNR vs INPUT FREQUENCY
75
LVDS Mode
73
72
SNR − dBFS
SNR - dBFS
74
71
70
69
68
67
66
65
0
50
100 150 200 250 300 350 400 450 500
75
74
73
72
71
70
69
68
67
66
65
64
63
10
DDR LVDS
CMOS Data
Position 1
CMOS Data
Position 2
CMOS Data
Position 3
CMOS Data
Position 4
20
30
40
Figure 23.
SFDR vs GAIN
100 130 170 300
SNR vs GAIN
75
4 dB
94
5 dB
0 dB
6 dB
SNR − dBFS
92
SFDR − dBc
70
Figure 24.
96
90
88
86
84
0 dB
82
2 dB
3 dB
74
1 dB
73
2 dB
72
3 dB
71
4 dB
70
5 dB
69
6 dB
1 dB
80
68
Input Adjusted to -1 dBFS
for Each Gain Setting
78
76
10
30
50
70
67
10
30
90 110 130 150 170 190 210 230
fIN − Input Frequency − MHz
Figure 25.
28
50
fIN − Input Frequency − MHz
fIN - Input Frequency - MHz
50
70
90 110 130 150 170 190 210 230
fIN − Input Frequency − MHz
Figure 26.
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
PERFORMANCE vs AVDD
PERFORMANCE vs DRVDD
SFDR
84
87
73.8
86
73.6
73.4
83
SNR
82
81
3
3.1
3.2
3.3
3.4
3.5
SNR
73.2
72.8
84
SFDR
83
73
82
fIN = 70 MHz
AVDD = 3.3 V
3.1
3.2
3.3
3.4
3.5
3.6
DRVDD − Supply Voltage − V
Figure 27.
Figure 28.
PERFORMANCE vs TEMPERATURE
SNR vs SAMPLING FREQUENCY
ACROSS POWER SCALING MODES
87
75.5
75
75
74
fIN = 70 MHz
SFDR
85
74.5
84
74
83
SNR − dBFS
86
SNR − dBFS
fIN = 70 MHz
SFDR − dBc
72.4
72.0
3.0
AVDD - Supply Voltage - V
−15
10
35
50
Default
73
Power Mode 3
Power Mode 1
72
73.5
Power Mode 2
SNR
82
−40
73.6
85
73.2
3.6
74.0
SNR − dBFS
SFDR - dBc
85
74
SFDR − dBc
fIN = 70 MHz
DRVDD = 3.3 V
SNR - dBFS
86
71
73
85
70
40
TA − Free-Air Temperature − oC
60
80
100
120
140
160
180
FS − Sampling Frequency − MSPS
Figure 29.
Figure 30.
PERFORMANCE vs CLOCK AMPLITUDE
86
95
74.8
84
74.5
82
SFDR (dBFS)
85
75
74.3
SNR
74.0
65
73.8
55
SFDR (dBc)
45
35
25
−60
fIN = 10 MHz
−50
−40
−30
−20
−10
0
74
73.5
SFDR
73
80
72.5
SNR
78
72
76
71.5
73.5
74
73.3
72
73.0
70
0.34
SNR − dBFS
75.0
SFDR − dBc
105
SNR − dBFS
SFDR − dBc, dBFS
PERFORMANCE vs
INPUT AMPLITUDE
71
fIN = 150 MHz
Sine Wave Input Clock
0.64
0.94
1.24
1.54
1.84
2.14
2.44
70.5
70
2.74
Input Clock Amplitude − VPP
Input Amplitude − dBFS
Figure 31.
Figure 32.
Submit Documentation Feedback
29
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
OUTPUT NOISE HISTOGRAM WITH
INPUTS SHORTED TO COMMON-MODE
PERFORMANCE vs INPUT CLOCK DUTY CYCLE
35
75.5
fIN = 10 MHz
15
10
SNR
73.5
55
60
65
Input Clock Duty Cycle − %
8200
50
8198
45
8199
40
8197
0
73.0
35
8196
82
30
5
8195
84
8194
74.0
8193
86
20
8192
74.5
25
8191
88
Occurence − %
SFDR
SNR − dBFS
SFDR − dBc
30
75.0
90
8190
92
Output Code
Figure 33.
Figure 34.
PERFORMANCE IN EXTERNAL REFERENCE MODE
88
COMMON-MODE REJECTION RATIO vs FREQUENCY
78
-35
77
-40
fIN = 70 MHz
86
76
82
75
80
74
SNR
CMRR − dBc
84
SNR − dBFS
SFDR − dBc
SFDR
-45
-50
-55
-60
78
73
76
1.4
72
-65
1.45
1.5
1.55
-70
0
1.6
1.21
1.16
1.11
1.06
1.01
0.96
0.91
0.86
0.81
0.76
0.71
0.66
0.61
20
60
80
Figure 35.
Figure 36.
POWER DISSIPATION vs
SAMPLING FREQUENCY (DDR LVDS)
DRVDD CURRENT vs
SAMPLING FREQUENCY (PARALLEL CMOS)
100
90
LVDS Mode
CMOS
10-pF Load Cap
80
Default
Power Mode 1
Power Mode 2
70
60
DDR LVDS
50
40
30
CMOS
0-pF Load Cap
20
CMOS
5-pF Load Cap
10
Power Mode 3
0
20
40
60
80
100
120
140
160 180
0
10
FS − Sampling Frequency − MSPS
Figure 37.
30
40
f - Frequency of AC Common-Mode Voltage - MHz
DRVDD Current − mA
PD − Power Dissipation − W
Voltage Forced on the CM Pin − V
30
50
70
90
110
Figure 38.
Submit Documentation Feedback
130
f − Frequency − MSPS
150
170
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All plots are at 25°C, AVDD = DRVDD = 3.3 V, sampling frequency = 170 MSPS, sine wave input clock, 1.5 VPP differential
clock amplitude, 50% clock duty cycle, –1 dBFS differential analog input, internal reference mode, 0 dB gain, DDR LVDS
data output (unless otherwise noted)
66
68
150
73
72
73
72
130
60
70
120
62
64
140
66
74
110
68
100
62
64
fS - Sampling Frequency - MSPS
70
74
160
72
73
170
90
70
80
66
74
70
64
68
50
100
150
200
250
300
350
400
450
70
72
500
fIN - Input Frequency - MHz
56
58
60
62
64
66
68
74
SNR - dBFS
Figure 39. SNR Contour in dBFS
80
85
85
85
85
75
65
70
60
50
70
70
90
110
85
90
80
120
90
90
130
75
85
85
140
55
90
100
60
65
80
85
80
70
75
90
90
fS - Sampling Frequency - MSPS
55
60
85
90
150
75
160
65
70
170
90
70
50
100
150
200
250
300
350
400
450
500
85
90
95
fIN - Input Frequency - MHz
45
50
55
60
65
70
75
80
SFDR - dBc
Figure 40. SFDR Contour in dBc
Submit Documentation Feedback
31
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION
THEORY OF OPERATION
ADS5545 is a low power 14-bit 170 MSPS pipeline ADC in a CMOS process. ADS5545 is based on switched
capacitor technology and runs off a single 3.3-V supply. The conversion process is initiated by a rising edge of
the external input clock. Once the signal is captured by the input sample and hold, the input sample is
sequentially converted by a series of lower resolution stages, with the outputs combined in a digital correction
logic block. At every clock edge, the sample propagates through the pipeline resulting in a data latency of 14
clock cycles. The output is available as 14-bit data, in DDR LVDS or CMOS and coded in either straight offset
binary or binary 2’s complement format.
ANALOG INPUT
The analog input consists of a switched-capacitor based differential sample and hold architecture, shown in
Figure 41.
This differential topology results in good ac-performance even for high input frequencies at high sampling rates.
The INP and INM pins have to be externally biased around a common-mode voltage of 1.5 V, available on VCM
pin 13. For a full-scale differential input, each input pin (INP, INM) has to swing symmetrically between VCM +
0.5 V and VCM – 0.5 V, resulting in a 2-VPP differential input swing. The maximum swing is determined by the
internal reference voltages REFP (2.5 V nominal) and REFM (0.5 V, nominal).
Sampling
Switch
Lpkg
6 nH
Sampling
Capacitor
R-C-R Filter
INP
Cbond
2 pF
25 W
50 W
Resr
200 W
4 pF
Lpkg
6 nH
Cpar2
1 pF
Ron
15 W
Ron
10 W
Cpar1
0.8 pF
50 W
Ron
15 W
25 W
Csamp
3.2 pF
Csamp
3.2 pF
INM
Cbond
2 pF
Resr
200 W
Sampling
Capacitor
Cpar2
1 pF
Sampling
Switch
Figure 41. Input Stage
The input sampling circuit has a 3-dB bandwidth that extends up to 500 MHz, see Figure 42, (measured from
the input pins to the voltage across the sampling capacitors).
32
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
ADC Input Impedance, ZI
2
500
0
450
400
350
-2
Magnitude − W
Magnitude − dB
Transfer Function - ADC Only
-4
-6
-8
-10
-12
-14
-16
0
100 200 300 400 500 600 700 800 900 1000
300
250
200
150
100
50
0
0
100 200 300 400 500 600 700 800 900 1000
f − Frequency − MHz
f − Frequency − MHz
Figure 42. Analog Input Bandwidth
(Data From Actual Silicon)
Figure 43. Impedance Looking Into INP, INM
(Data From Simulation)
Driving Circuit
A 5-Ω resistor in series with each input pin is recommended to damp out ringing caused by the package
parasitics. It is also necessary to present a low impedance (< 50 Ω) for the common-mode switching currents.
For example, this is achieved by using two resistors from each input terminated to the common-mode voltage
(VCM).
In addition to the above ADC requirements, the drive circuit may have to be designed to provide a low insertion
loss over the desired frequency range and matched impedance to the source. For this, the ADC input
impedance has to be considered, see Figure 43.
Example Drive Circuits
A configuration suitable for low input frequency ranges (< 100 MHz) is shown in Figure 44. Note the 5-Ω series
resistors and the low common-mode impedance (using 25-Ω resistors terminated to VCM). In addition, the circuit
has low insertion loss, and good impedance match at low input frequencies, see Figure 45.
ADS5545
0.1 mF
ADT1-1WT
5W
INP
0.1 mF
25 W
25 W
INM
5W
1:1
S11, ZI
VCM
Figure 44. Drive Circuit at Low Input Frequencies
Submit Documentation Feedback
33
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
S11
0
-10
S11 − dB
-20
-30
-40
S(1, 1)
-50
-60
-70
0
50
100
150
200
250
f − Frequency − MHz
Transfer Function − Source To ADC Output
(Including the Transformer)
Frequency (100 kHz to 500 MHz)
3
Frequency = 100 MHz
S(1, 1) = 0.11/-1.19E2
Impedance = 44.07 - j8.63
Magnitude − dB
1
-1
-3
-5
-7
-9
0
50
100
150
200
250
f − Frequency − MHz
Figure 45. S11, Input Impedance and Transfer Function for the Configuration in Figure 44
For high input frequencies, the previous configuration has been modified to improve the insertion loss and
impedance matching (see Figure 46). The S11 curve shows that the matching is good from 100 MHz to
300 MHz.
34
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
ADS5545
TC4-1W
0.1 mF
12 nH
(Note A)
TC4-1W
5W
INP
0.1 mF
50 W
50 W
INM
1:2
12 nH
(Note A)
2:1
5W
S11, ZI
A.
VCM
Includes transformer leakage inductances.
Figure 46. Configuration for High Input Frequencies
S11
0
-5
S11 − dB
-10
S(1, 1)
-15
-20
-25
0
100 200 300 400 500 600 700 800 900 1000
f − Frequency − MHz
Transfer Function − Source to ADC Output
(Including the Transformer)
Frequency (100 kHz to 500 MHz)
2
Frequency = 200 MHz
S(1, 1) = 0.09/50.92
Impedance = 55.57 + j8.03
Magnitude − dB
0
-2
-4
-6
-8
-10
0
50
100 150 200 250 300 350 400 450 500
f − Frequency − MHz
Figure 47. S11, Input Impedance and Transfer Function for the Configuration in Figure 46
Submit Documentation Feedback
35
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
Using RF Transformer-Based Drive Circuits
For optimum performance, the analog inputs must be driven differentially. This improves the common-mode
noise immunity and even order harmonic rejection. Some examples of input configurations using RF
transformers suitable for low and high input frequencies are shown in Figure 46 and Figure 47.
The single-ended signal is fed to the primary winding of the RF transformer. The transformer is terminated on
the secondary side. Putting the termination on the secondary side helps to shield the kickbacks caused by the
sampling circuit from the RF transformer’s leakage inductances. The termination is accomplished by two
resistors connected in series, with the center point connected to the 1.5 V common-mode (VCM pin 13). The
value of the termination resistors (connected to common-mode) has to be low (< 100 Ω) to provide a
low-impedance path for the ADC common-mode switching current.
At high input frequencies, the mismatch in the transformer parasitic capacitance (between the windings) results
in degraded even-order harmonic performance. Connecting two identical RF transformers back-to-back helps
minimize this mismatch, and good performance is obtained for high frequency input signals. An additional
termination resistor pair (enclosed within the shaded box in Figure 46) may be required between the two
transformers to improve the balance between the P and M sides. The center point of this termination must be
connected to ground. (Note that the drive circuit has to be tuned to account for this additional termination, to get
the desired S11 and impedance match).
Using Differential Amplifier Drive Circuits
Figure 48 shows a drive circuit using a differential amplifier (THS4509) to convert a single-ended input to
differential output that can be interface to the ADC analog input pins. In addition to the single-ended to
differential conversion, the amplifier also provides gain (10 dB in Figure 48). RFIL helps to isolate the amplifier
outputs from the switching input of the ADC. Together with CFIL it also forms a low-pass filter that band-limits the
noise (and signal) at the ADC input. As the amplifier output is ac-coupled, the common-mode voltage of the ADC
input pins is set using two 200 Ω resistors connected to VCM.
The amplifier output can also be dc-coupled. Using the output common-mode control of the THS4509, the ADC
input pins can be biased to 1.5 V. In this case, use +4 V and -1 V supplies for the THS4509 so that the output
common-mode voltage (1.5V) is at the supply mid-point.
RF
+VS
500 W
0.1 mF
RS
0.1 mF 10 mF
RFIL
0.1 mF
5W
INP
RG
0.1 mF
RT
CFIL
200 W
CFIL
200 W
CM THS4509
RG
RFIL
INM
RS || RT
0.1 mF
5W
0.1 mF
500 W
VCM
–VS
0.1 mF 10 mF
0.1 mF
RF
Figure 48. Drive Circuit Using the THS4509
See the EVM User Guide (SLWU028) for more information.
36
Submit Documentation Feedback
ADS5545
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
Input Common-Mode
To ensure a low-noise common-mode reference, the VCM pin is filtered with a 0.1-µF low-inductance capacitor
connected to ground. The VCM pin is designed to directly drive the ADC inputs. The input stage of the ADC
sinks a common-mode current in the order of 280 µA (at 170 MSPS). Equation 1 describes the dependency of
the common-mode current and the sampling frequency.
(280 mA) x Fs
170 MSPS
(1)
This equation helps to design the output capability and impedance of the CM driving circuit accordingly.
Reference
ADS5545 has built-in internal references REFP and REFM, requiring no external components. Design schemes
are used to linearize the converter load seen by the references; this and the integration of the requisite
reference capacitors on-chip eliminates the need for external decoupling. The full-scale input range of the
converter can be controlled in the external reference mode as explained below. The internal or external
reference modes can be selected by controlling the MODE pin 23 (see Table 7 for details) or by programming
the serial interface register bit <REF> (Table 16).
INTREF
Internal
Reference
VCM
INTREF
EXTREF
REFM
REFP
ADS5545
Figure 49. Reference Section
Internal Reference
When the device is in internal reference mode, the REFP and REFM voltages are generated internally.
Common-mode voltage (1.5 V nominal) is output on VCM pin, which can be used to externally bias the analog
input pins.
Submit Documentation Feedback
37
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
External Reference
When the device is in external reference mode, the VCM acts as a reference input pin. The voltage forced on
the VCM pin is buffered and gained by 1.33 internally, generating the REFP and REFM voltages. The differential
input voltage corresponding to full-scale is given by Equation 2.
Full−scale differential input pp + (Voltage forced on VCM) 1.33
(2)
In this mode, the 1.5 V common-mode voltage to bias the input pins has to be generated externally. There is no
change in performance compared to internal reference mode.
Low Sampling Frequency Operation
For best performance at high sampling frequencies, ADS5545 uses a clock generator circuit to derive internal
timing for the ADC. The clock generator operates from 170 MSPS down to 50 MSPS in the DEFAULT SPEED
mode. The ADC enters this mode after applying reset (with serial interface configuration) or by tying SCLK pin to
low (with parallel configuration).
For low sampling frequencies (below 50 MSPS), the ADC must be put in the LOW SPEED mode. This mode
can be entered by:
• setting the register bit <LOW SPEED> (Table 10) through the serial interface, OR
• tying the SCLK pin to high (Table 3) using the parallel configuration.
Clock Input
ADS5545 clock inputs can be driven differentially (SINE, LVPECL or LVDS) or single-ended (LVCMOS), with
little or no difference in performance between configurations. The common-mode voltage of the clock inputs is
set to VCM using internal 5-kΩ resistors as shown in Figure 50. This allows the use of transformer-coupled drive
circuits for sine wave clock, or ac-coupling for LVPECL, LVDS clock sources (Figure 51 and Figure 52)
VCM
VCM
5 kW
5 kW
CLKP
CLKM
ADS5545
Figure 50. Internal Clock Buffer
38
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
For best performance, it is recommended to drive the clock inputs differentially, reducing susceptibility to
common-mode noise. In this case, it is best to connect both clock inputs to the differential input clock signal with
0.1-µF capacitors, as in Figure 51.
0.1 mF
CLKP
Differential Sine-Wave
or PECL or LVDS
Clock Input
0.1 mF
CLKM
ADS5545
Figure 51. Differential Clock Driving Circuit
A single-ended CMOS clock can be ac-coupled to the CLKP input, with CLKM (pin 11) connected to ground with
a 0.1-µF capacitor, as in Figure 52.
0.1 mF
CMOS Clock Input
CLKP
0.1 mF
CLKM
ADS5545
Figure 52. Single-Ended Clock Driving Circuit
For best performance, the clock inputs have to be driven differentially, reducing susceptibility to common-mode
noise. For high input frequency sampling, the use a clock source with very low jitter is recommended. Bandpass
filtering of the clock source can help reduce the effect of jitter. There is no change in performance with a
non-50% duty cycle clock input. Figure 33 shows the performance variation of the ADC versus clock duty cycle
Input Clock Buffer Gain
When using a sinusoidal clock input, the noise contributed by clock jitter improves as the clock amplitude is
increased. Therefore, using a large amplitude clock is recommended. In addition, the clock buffer has a
programmable gain option to amplify the input clock. There are 5 gain settings, with Gain 4 being the maximum
gain and Gain 0 the minimum gain setting. The default gain is Gain 1. The clock buffer gain can be set by
programming the register bits <CLKIN GAIN> (Table 14).
Submit Documentation Feedback
39
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
APPLICATION INFORMATION (continued)
Programmable Gain
ADS5545 has programmable gain from 0 dB to 6 dB in steps of 1 dB. The corresponding full-scale input range
varies from 2 VPP down to 1 VPP, with 0 dB being the default gain. At high IF, this is especially useful as the
SFDR improvement is significant with marginal degradation in SNR.
The gain can be programmed using the register bits <GAIN> (Table 12).
Table 19. Full-scale Range Across Gains
Gain
Corresponding full-scale range, Vpp
0 dB
2.00
1 dB
1.78
2 dB
1.59
3 dB
1.42
4 dB
1.26
5 dB
1.12
6 dB
1.00
Power Down
ADS5545 has three power-down modes – global STANDBY, output buffer disabled, and input clock stopped.
Global STANDBY
This mode can be initiated by controlling SDATA (pin 28) or by setting the register bit <STBY> (Table 10)
through the serial interface. In this mode, the A/D converter, reference block and the output buffers are powered
down and the total power dissipation reduces to about 100 mW. The output buffers are in high impedance state.
The wake-up time from the global power down to data becoming valid normal mode is maximum 100 µs.
Output Buffer Disable
The output buffers can be disabled using OE pin 7 in both the LVDS and CMOS modes, reducing the total
power by about 100 mW. With the buffers disabled, the outputs are in high impedance state. The wake-up time
from this mode to data becoming valid in normal mode is maximum 1 µs in LVDS mode and 50 ns in CMOS
mode.
Input Clock Stop
The converter enters this mode when the input clock frequency falls below 1 MSPS. The power dissipation is
about 100 mW and the wake-up time from this mode to data becoming valid in normal mode is maximum
100 µs.
40
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Power Scaling Modes
ADS5545 has a power scaling mode in which the device can be operated at reduced power levels at lower
sampling frequencies with no difference in performance. (Figure 30) (1) There are four power scaling modes for
different sampling frequency ranges which can be programmed using the serial interface register bits
<SCALING> (see Table 16 ). Only the AVDD power is scaled, leaving the DRVDD power unchanged.
Table 20. Power Scaling vs Sampling Speed
Sampling Frequency
MSPS
(1)
Power Scaling Mode
Analog Power
(Typical)
Analog Power in Default Mode
> 150
Default
928 mW at 170 MSPS
928 mW at 170 MSPS
105 to 150
Power Mode 1
841 mW at 150 MSPS
917 mW at 150 MSPS
50 to 105
Power Mode 2
670 mW at 105 MSPS
830 mW at 105 MSPS
< 50
Power Mode 3
525 mW at 50 MSPS
760 mW at 50 MSPS
The performance in the power scaling modes is from characterization and not tested in production.
Power Supply Sequence
During power-up, the AVDD and DRVDD supplies can come up in any sequence. The two supplies are
separated inside the device. Externally, they can be driven from separate supplies or from a single supply.
Digital Output Information
ADS5545 provides 14-bit data, an output clock synchronized with the data and an out-of-range indicator that
goes high when the output reaches the full-scale limits. In addition, output enable control (OE pin 7) is provided
to power down the output buffers and put the outputs in high-impedance state.
Output Interface
Two output interface options are available – Double Data Rate (DDR) LVDS and parallel CMOS. They can be
selected using the DFS (Table 6) or the serial interface register bit <ODI> (Table 15).
DDR LVDS Outputs
In this mode, the 14 data bits and the output clock are available as LVDS (Low Voltage Differential Signal)
levels. Two successive data bits are multiplexed and output on each LVDS differential pair as shown in
Figure 53. So, there are 7 LVDS output pairs for the 14 data bits and 1 LVDS output pair for the output clock.
Submit Documentation Feedback
41
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Pins
CLKOUTP
Output Clock
CLKOUTM
D0_D1_P
Data Bits D0. D1
D0_D1_M
D2_D3_P
Data Bits D2, D3
D2_D3_M
D4_D5_P
Data Bits D4, D5
D4_D5_M
D6_D7_P
Data Bits D6, D7
D6_D7_M
D8_D9_P
Data Bits D8, D9
D8_D9_M
D10_D11_P
Data Bits D10, D11
D10_D11_M
D12_D13_P
Data Bits D12, D13
D12_D13_M
OVR
Out-of-Range Indicator
ADS5545
Figure 53. DDR LVDS Outputs
Even data bits D0, D2, D4, D6, D8, D10, and D12 are output at the falling edge of CLKOUTP and the odd data
bits D1, D3, D5, D7, D9, D11, and D13 are output at the rising edge of CLKOUTP. Both the rising and falling
edges of CLKOUTP have to be used to capture all the 14 data bits (Figure 54).
42
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
CLKOUTP
CLKOUTM
D0_D1_P,
D0_D1_M
D0
D1
D0
D1
D2_D3_P,
D2_D3_M
D2
D3
D2
D3
D4_D5_P,
D4_D5_M
D4
D5
D4
D5
D6_D7_P,
D6_D7_M
D6
D7
D6
D7
D8_D9_P,
D8_D9_M
D8
D9
D8
D9
D10_D11_P,
D10_D11_M
D10
D11
D10
D11
D12_D13_P,
D12_D13_M
D12
D13
D12
D13
Sample N
Sample N+1
T0110-01
Figure 54. DDR LVDS Interface
LVDS Buffer Current Programmability
The default LVDS buffer output current is 3.5 mA. When terminated by 100 Ω, this results in a 350-mV
single-ended voltage swing (700-mVPP differential swing). The LVDS buffer currents can also be programmed to
2.5 mA, 4.5 mA, and 1.75 mA using the register bits <LVDS CURR> (Table 17). In addition, there exists a
current double mode, where this current is doubled for the data and output clock buffers (register bits <CURR
DOUBLE>) (Table 18).
LVDS Buffer Internal Termination
An internal termination option is available (using the serial interface), by which the LVDS buffers are differentially
terminated inside the device. The termination resistances available are – 325, 200, and 170 Ω (nominal with
±20% variation). Any combination of these three terminations can be programmed; the effective termination is
the parallel combination of the selected resistances. This results in eight effective terminations from open (no
termination) to 75 Ω.
The internal termination helps to absorb any reflections coming from the receiver end, improving the signal
integrity. With 100-Ω internal and 100-Ω external termination, the voltage swing at the receiver end is halved
(compared to no internal termination). The voltage swing can be restored by using the LVDS current double
mode. Figure 55 shows the eye diagram of one of the LVDS data outputs with a 10-pF load capacitance (from
each pin to ground) and 100-Ω internal termination enabled. The terminations can be programmed using register
bits <DATA TERM> and <CLKOUT TERM> (Table 17).
Submit Documentation Feedback
43
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Figure 55. Eye Diagram of LVDS Data Output With Internal Termination and 10-pF capacitance load
Parallel CMOS
In this mode, the 14 data outputs and the output clock are available as 3.3-V CMOS voltage levels. Each data
bit and the output clock is available on a separate pin in parallel. By default, the data outputs are valid during the
rising edge of the output clock. The output clock is CLKOUT (pin 5).
CMOS Mode Power Dissipation
With CMOS outputs, the DRVDD current scales with the sampling frequency and the load capacitance on every
output pin (see Figure 38). The maximum DRVDD current occurs when each output bit toggles between 0 and 1
every clock cycle. In actual applications, this condition is unlikely to occur. The actual DRVDD current is
determined by the average number of output bits switching, which is a function of the sampling frequency and
the nature of the analog input signal.
Digital current due to CMOS output switching = CL x VDRVDD x (N x FAVG)
where CL = load capacitance, N x FAVG = average number of output bits switching
Figure 38 shows the current with various load capacitances across sampling frequencies at 2 MHz analog input
frequency.
Output Switching Noise and Data Position Programmability (in CMOS mode ONLY)
Switching noise (caused by CMOS output data transitions) can couple into the analog inputs during the instant
of sampling and degrade the SNR. To minimize this, the device includes programmable options to move the
output data transitions with respect to the output clock. This can be used to position the data transitions at the
optimum place away from the sampling instant and improve the SNR. Figure 24 shows the variation of SNR for
different CMOS output data positions at 190 MSPS.
Note that the optimum output data position varies with the sampling frequency. The data position can be
programmed using the register bits <DATA POSN> (Table 9).
It is recommended to put series resistors (50 to 100 Ω) on each output line placed very close to the converter
pins. This helps to isolate the outputs from seeing large load capacitances and in turn reduces the amount of
switching noise. For example, the data in Figure 24 was taken with 50 Ω series resistors on each output line.
44
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Output Clock Position Programmability
In both the LVDS and CMOS modes, the output clock can be moved around its default position. This can be
done using SEN pin 27 (as described in Table 5) or using the register bits <CLKOUT POSN> (Table 9). Using
this allows to trade-off the setup and hold times leading to reliable data capture. There also exists an option to
align the output clock edge with the data transition.
Note that programming the output clock position also affects the clock propagation delay times.
Output Data Format
Two output data formats are supported – 2's complement and offset binary. They can be selected using the DFS
(pin 6) or the serial interface register bit <DF> (Table 10).
Out-of-range Indicator (OVR)
When the input voltage exceeds the full-scale range of the ADC, OVR (pin 3) goes high, and the output code is
clamped to the appropriate full-scale level for the duration of the overload. For a positive overdrive, the output
code is 0x3FFF in offset binary output format, and 0x1FFF in 2's complement output format. For a negative input
overdrive, the output code is 0x0000 in offset binary output format and 0x2000 in 2's complement output format.
Figure 56 shows the behavior of OVR during the overload. Note that OVR and the output code react to the
overload after a latency of 14 clock cycles.
Figure 56. OVR During Input Overvoltage
Output Timing
For the best performance at high sampling frequencies, ADS5545 uses a clock generator circuit to derive
internal timing for ADC. This results in optimal setup and hold times of the output data and 50% output clock
duty cycle for sampling frequencies from 80 MSPS to 170 MSPS. See Table 21 for timing information above 80
MSPS.
Submit Documentation Feedback
45
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Table 21. Timing Characteristics (80 MSPS to 170 MSPS)
Fs, MSPS
tsu DATA SETUP TIME, ns (2)
MIN
TYP
150
1.6
130
2.0
80
th DATA HOLD TIME, ns (2)
MAX
MIN
TYP
2.1
0.6
1.1
2.5
0.8
1.3
3.6
4.1
1.6
150
2.8
3.6
130
3.3
4.1
80
6
7
(1)
tPDI CLOCK PROPAGATION DELAY, ns (3)
MAX
MIN
TYP
MAX
4.3
5
5.7
4.5
5.2
5.9
2.1
4.7
5.7
6.7
1.2
1.6
1.7
2.5
3.3
1.7
2.1
1.1
1.9
2.7
3.7
4.1
10.8
12
13.2
DDR LVDS
PARALLEL CMOS
(1)
(2)
(3)
Timing parameters are specified by design and characterization and not tested in production.
Setup and hold times are specified with default output clock and data positions. For other positions, the timing numbers have to be
adjusted appropriately.
Clock propagation delay timings are specified with default output clock positions. For other positions, the timing numbers have to be
adjusted appropriately.
Below 80 MSPS, the setup and hold times do not scale with the sampling frequency. The output clock duty cycle
also progressively moves away from 50% as the sampling frequency is reduced from 80 MSPS.
See Table 22 for detailed timings at sampling frequencies below 80 MSPS. Figure 57 shows the clock duty cycle
across sampling frequencies in the DDR LVDS and CMOS modes.
Table 22. Timing Characteristics (1 MSPS to 80 MSPS)
Fs, MSPS
tsu DATA SETUP TIME, ns (2)
MIN
TYP
th DATA HOLD TIME, ns (2)
MAX
MIN
TYP
(1)
tPDI CLOCK PROPAGATION DELAY, ns (3)
MAX
MIN
TYP
MAX
DDR LVDS
1 to 80
3.6
1.6
5.7
6
3.7
12
PARALLEL CMOS
1 to 80
(1)
(2)
Output Clock Duty Cycle − %
(3)
Timing parameters are specified by design and characterization and not tested in production.
Setup and hold times are specified with default output clock and data positions. For other positions, the timing numbers have to be
adjusted appropriately.
Clock propagation delay timings are specified with default output clock positions. For other positions, the timing numbers have to be
adjusted appropriately.
100
90
80
70
60
DDR LVDS
50
40
CMOS
30
20
10
0
0
20
40
60
80
100 120
140 160
180
Sampling Frequency − MHz
Figure 57. Output Clock Duty Cycle (typical) vs Sampling Frequency
The latency of ADS5545 is 14 clock cycles from the sampling instant (input clock rising edge). In the LVDS
mode, the latency remains constant across sampling frequencies. In the CMOS mode, the latency is 14 clock
cycles above 80 MSPS and 13 clock cycles below 80 MSPS.
46
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
Board Design Considerations
Grounding
A single ground plane is sufficient to give good performance, provided the analog, digital and clock sections of
the board are cleanly partitioned. See the EVM User Guide (SLWU028) for details on layout and grounding.
Supply Decoupling
As the ADS5546 already includes internal decoupling, minimal external decoupling can be used without loss in
performance. Note that decoupling capacitors can help to filter external power supply noise, so the optimum
number of capacitors would depend on the actual application. The decoupling capacitors should be placed very
close to the converter supply pins.
It is recommended to use separate supplies for the analog and digital supply pins to isolate digital switching
noise from sensitive analog circuitry. In case only a single 3.3-V supply is available, it should be routed first to
AVDD. It can then be tapped and isolated with a ferrite bead (or inductor) with decoupling capacitor, before
being routed to DRVDD.
Series Resistors on Data Outputs
It is recommended to put series resistors (50 to 100 Ω) on each output line placed very close to the converter
pins. This helps to isolate the outputs from seeing large load capacitances and in turn reduces the amount of
switching noise.
Exposed Thermal Pad
For best thermal performance, it is necessary to solder the exposed pad at the bottom of the package to a
ground plane using multiple vias. For detailed information, see application notes QFN Layout Guidelines
(SLOA122) and QFN/SON PCB Attachment (SLUA271).
Submit Documentation Feedback
47
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DEFINITION OF SPECIFICATIONS
Analog Bandwidth
The analog input frequency at which the power of the fundamental is reduced by 3 dB with respect to the low
frequency value.
Aperture Delay
The delay in time between the rising edge of the input sampling clock and the actual time at which the sampling
occurs.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Clock Pulse Width/Duty Cycle
The duty cycle of a clock signal is the ratio of the time the clock signal remains at a logic high (clock pulse width)
to the period of the clock signal. Duty cycle is typically expressed as a percentage. A perfect differential
sine-wave clock results in a 50% duty cycle.
Maximum Conversion Rate
The maximum sampling rate at which certified operation is given. All parametric testing is performed at this
sampling rate unless otherwise noted.
Minimum Conversion Rate
The minimum sampling rate at which the ADC functions.
Differential Nonlinearity (DNL)
An ideal ADC exhibits code transitions at analog input values spaced exactly 1 LSB apart. The DNL is the
deviation of any single step from this ideal value, measured in units of LSBs
Integral Nonlinearity (INL)
The INL is the deviation of the ADC’s transfer function from a best fit line determined by a least squares curve fit
of that transfer function, measured in units of LSBs.
Gain Error
The gain error is the deviation of the ADC’s actual input full-scale range from its ideal value. The gain error is
given as a percentage of the ideal input full-scale range.
Offset Error
The offset error is the difference, given in number of LSBs, between the ADC’s actual average idle channel
output code and the ideal average idle channel output code. This quantity is often mapped into mV.
Temperature Drift
The temperature drift coefficient (with respect to gain error and offset error) specifies the change per degree
Celsius of the parameter from TMIN to TMAX. It is calculated by dividing the maximum deviation of the parameter
across the TMIN to TMAX range by the difference TMAX–TMIN.
48
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DEFINITION OF SPECIFICATIONS (continued)
Signal-to-Noise Ratio
SNR is the ratio of the power of the fundamental (PS) to the noise floor power (PN), excluding the power at dc
and the first nine harmonics.
P
SNR + 10Log 10 s
PN
(4)
SNR is either given in units of dBc (dB to carrier) when the absolute power of the fundamental is used as the
reference, or dBFS (dB to full scale) when the power of the fundamental is extrapolated to the converter’s
full-scale range.
Signal-to-Noise and Distortion (SINAD)
SINAD is the ratio of the power of the fundamental (PS) to the power of all the other spectral components
including noise (PN) and distortion (PD), but excluding dc.
Ps
SINAD + 10Log 10
PN ) PD
(5)
SINAD is either given in units of dBc (dB to carrier) when the absolute power of the fundamental is used as the
reference, or dBFS (dB to full scale) when the power of the fundamental is extrapolated to the converter’s
full-scale range.
Effective Number of Bits (ENOB)
The ENOB is a measure of a converter’s performance as compared to the theoretical limit based on quantization
noise.
ENOB + SINAD * 1.76
6.02
(6)
Total Harmonic Distortion (THD)
THD is the ratio of the power of the fundamental (PS) to the power of the first nine harmonics (PD).
P
THD + 10Log 10 s
PN
(7)
THD is typically given in units of dBc (dB to carrier).
Spurious-Free Dynamic Range (SFDR)
The ratio of the power of the fundamental to the highest other spectral component (either spur or harmonic).
SFDR is typically given in units of dBc (dB to carrier).
Two-Tone Intermodulation Distortion
IMD3 is the ratio of the power of the fundamental (at frequencies f1 and f2) to the power of the worst spectral
component at either frequency 2f1–f2 or 2f2–f1. IMD3 is either given in units of dBc (dB to carrier) when the
absolute power of the fundamental is used as the reference, or dBFS (dB to full scale) when the power of the
fundamental is extrapolated to the converter’s full-scale range.
DC Power Supply Rejection Ratio (DC PSRR)
The DC PSSR is the ratio of the change in offset error to a change in analog supply voltage. The DC PSRR is
typically given in units of mV/V.
Submit Documentation Feedback
49
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
DEFINITION OF SPECIFICATIONS (continued)
AC Power Supply Rejection Ratio (AC PSRR)
AC PSRR is the measure of rejection of variations in the supply voltage of the ADC. If ∆VSUP is the change in
the supply voltage and ∆VOUT is the resultant change in the ADC output code (referred to the input), then
DVOUT
PSRR = 20Log 10
(Expressed in dBc)
DVSUP
(8)
Common Mode Rejection Ratio (CMRR)
CMRR is the measure of rejection of variations in the input common-mode voltage of the ADC. If ∆Vcm is the
change in the input common-mode voltage and ∆VOUT is the resultant change in the ADC output code (referred
to the input), then
DVOUT
CMRR = 20Log10
(Expressed in dBc)
DVCM
(9)
Voltage Overload Recovery
The number of clock cycles taken to recover to less than 1% error for a 6-dB overload on the analog inputs. A
6-dBFS sine wave at Nyquist frequency is used as the test stimulus.
50
Submit Documentation Feedback
ADS5545
www.ti.com
SLWS180C – NOVEMBER 2005 – REVISED MAY 2007
ADS5545 Revision history
Revision
Date
Description
A
03/06
Added new graphs to the Typical Characteristics. Added the Application Information section.
B
09/06
New Timing Characteristics table. Revised the Application Information section.
New text for the Device Mode Configuration.
Parallel Pin Control section changed to Parallel Configuration Only section.
Added Serial Interface Configuration Only section.
Added Configuration using Both the Serial Interface and Parallel Controls.
New text for the Serial Interface section
Added Register Reset section.
Additions to <RST> and <GAIN>.
Revised Typical Characteristics graphs.
Added Programmable gain section in the Application Information
C
04/07
Added thermal pad to Figure 7 and Figure 8.
Added Graph DRVDD Current (Figure 38).
Changed the Application Information section and figures.
Changed Drive Circuit and Example Drive Circuit information and figures.
Added Using RF Transformer-Based Drive Circuits information
Added Using Differential Amplifier Drive Circuits information.
Added CMOS Mode Power Dissipation
Added Overvoltage Signal information and Figure 56.
Added Output Data Position Programmability section
Added min/max specifications for offset error and gain error.
Changed the Serial Register tables. Changed Figure 24
Submit Documentation Feedback
51
PACKAGE OPTION ADDENDUM
www.ti.com
31-Oct-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADS5545IRGZT
ACTIVE
VQFN
RGZ
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
AZ5545
ADS5545IRGZTG4
ACTIVE
VQFN
RGZ
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
AZ5545
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
31-Oct-2013
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADS5545IRGZT
Package Package Pins
Type Drawing
VQFN
RGZ
48
SPQ
250
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
180.0
16.4
Pack Materials-Page 1
7.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
7.3
1.5
12.0
16.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADS5545IRGZT
VQFN
RGZ
48
250
213.0
191.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated