Anachip AP1115AV33A 0.6a low dropout positive adjustable or fixed-mode regulator Datasheet

AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Features
•
•
•
•
•
•
•
„ General Description
AP1115 is a low dropout positive adjustable or
fixed-mode regulator with minimum of 0.6A output
current capability. The product is specifically
designed to provide well-regulated supply for low
voltage IC applications such as high-speed bus
termination and low current 3.3V logic supply.
AP1115 is also well suited for other applications
such as VGA cards. AP1115 is guaranteed to have
<1.3V dropout at full load current making it ideal to
provide well regulated outputs of 1.25V to 5V with
up to 18V input supply.
1.3V maximum dropout at full load current
Fast transient response
Output current limiting
Built-in thermal shutdown
Packages: SOT89, TO92
Good noise rejection
3-Terminal Adjustable or Fixed 1.5V / 1.8V / 2.5V
/ 2.8V / 3.0V / 3.3V / 3.5V / 5.0V
„ Applications
•
•
PC peripheral
Communication
„ Connection Diagram (Top View)
AP1115A-3 PIN SOT89
AP1115A-3 PIN TO92
3
Vin
2
Adj (GND)
2 GND
1
Vout
1 Vin
3 Vout
Tab is Pin2
AP1115B-3 PIN SOT89
AP1115B-3 PIN TO92
3
Vout
2
Vin
2 Vin
1
Adj (GND)
1 GND
3 Vout
Tab is Pin2
„ Pin Descriptions
NAME
Adj
(GND)
I/O
Vout
O
Vin
I
I
FUNCTION
A resistor divider from this pin to the Vout pin and ground sets the output voltage.
(Ground only for Fixed-Mode)
The output of the regulator. A minimum of 10uF capacitor (0.15Ω ≤ ESR ≤ 20Ω)
must be connected from this pin to ground to insure stability.
The input pin of regulator. Typically a large storage capacitor (0.15Ω ≤ ESR ≤
20Ω) is connected from this pin to ground to insure that the input voltage does not
sag below the minimum dropout voltage during the load transient response. This
pin must always be 1.3V higher than Vout in order for the device to regulate
properly.
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev.1.1 Aug.27, 2004
1/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Ordering Information
AP 1115 X X XX X X
Low Dropout Regulator
Pin Version
Package
A: Pin1:Vout
Y : SOT89-3L
2:Adj(GND) V : TO92-3L
3:Vin
B: Pin1:Adj(GND)
2:Vin
3:Vout
„ Typical Circuit
Vout
Lead Free
5V
5V
C1
100uF
C1
100uF
Vin
Vin
GND
Adj
Vout
Vout
3.3V/0.5A
C2
100uF
R2
121O
VO
2.5V/0.5A
AP1115A (5V/2.5V Adj output)
5V
C1
100uF
5V
C1
100uF
Vin
R1
121O
C2
100uF
AP1115A (5V/3.3V fixed output)
Vout
Packing
Blank : Tube
Blank : ADJ Blank : Normal
15 : 1.5V
L : Lead Free Package A : Taping
18 : 1.8V
25 : 2.5V
28 : 2.8V
30 : 3.0V
33 : 3.3V
35 : 3.5V
50 : 5.0V
VO
2.5V/0.5A
Vout
3.3V/0.5A
C2
100uF
Vin
Adj
GND
C2
R1
121O 100uF
R2
121O
AP1115B (5V/2.5V Adj output)
AP1115B (5V/3.3V fixed output)
Note: Vo = VREF ∗ (1+
R2
)
R1
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev.1.1 Aug.27, 2004
2/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Absolute Maximum Ratings
Symbol
VIN
PD
TST
TOP
Parameter
DC Supply Voltage
Power Dissipation
Storage Temperature
Operating Junction Temperature Range
Rating
-0.3 to 18 V
Internally Limited
-65 to +150
0 to +150
Unit
V
o
o
C
C
„ Electrical Characteristics (Under Operating Conditions)
PARAMETER
Reference Voltage
AP1115-ADJ
AP1115-1.5
AP1115-1.8
AP1115-2.5
AP1115-2.8
Output Voltage
AP1115-3.0
AP1115-3.3
AP1115-3.5
AP1115-5.0
Line Regulation
AP1115-XXX
AP1115-ADJ
AP1115-1.5
AP1115-1.8
AP1115-2.5
Load Regulation
AP1115-2.8
AP1115-3.0
AP1115-3.3
AP1115-3.5
AP1115-5.0
Dropout Voltage
(VIN-VOUT)
Current Limit
Minimum Load Current
Thermal Regulation
CONDITIONS
o
TJ=25 C,(VIN-OUT)=1.5V
IO=10mA
o
IOUT = 10mA, TJ = 25 C,
3V≦VIN≦12V
IOUT = 10mA, TJ = 25oC,
3.3V≦VIN≦12V
o
IOUT = 10mA, TJ = 25 C,
4V≦VIN≦12V
IOUT = 10mA, TJ = 25oC,
4.3V≦VIN≦12V
o
IOUT = 10mA, TJ = 25 C,
4.5V≦VIN≦12V
o
IOUT = 10mA, TJ = 25 C,
4.8V≦VIN≦12V
o
IOUT = 10mA, TJ = 25 C,
5V≦VIN≦12V
IOUT = 10mA, TJ = 25oC,
6.5V≦VIN≦12V
IO=10mA,VOUT+1.5V<VIN<15V,
o
TJ=25 C
VIN=3.3V,Vadj=0,0mA<Io<0.6A,
o
TJ=25 C (Note 1,2)
VIN=3V, 0mA<Io<0.6A,
o
TJ=25 C (Note 1,2)
VIN=3.3V, 0mA<Io<0.6A,
o
TJ=25 C (Note 1,2)
VIN=4V, 0mA<Io<0.6A,
o
TJ=25 C (Note 1,2)
VIN=4.3V, 0mA<Io<0.6A,
TJ=25oC (Note 1,2)
VIN =5V, 0≦IOUT≦0.6A,
o
TJ=25 C (Note 1,2)
VIN =5V, 0≦IOUT≦0.6A,
TJ=25oC (Note 1,2)
VIN =5V, 0≦IOUT≦0.6A,
o
TJ=25 C (Note 1,2)
VIN =8V, 0≦IOUT≦0.6A,
o
TJ=25 C (Note 1,2)
AP1115-ADJ/1.5/1.8
2.5/2.8/3.0/3.3/3.5/5.0
AP1115-ADJ/1.5/1.8
2.5/2.8/3.0/3.3/3.5/5.0
AP1115-XXX
o
TA=25 C, 30ms pulse
IOUT = 0.6A, ∆VOUT=0.1%VOUT
(VIN-VOUT) = 5V
o
o
0 C≦Tj≦125 C
Anachip Corp.
www.anachip.com.tw
MIN
TYP
MAX
UNIT
1.225
1.250
1.275
V
1.470
1.500
1.530
V
1.764
1.800
1.836
V
2.450
2.500
2.550
V
2.744
2.800
2.856
V
2.940
3.000
3.060
V
3.235
3.300
3.365
V
3.430
3.500
3.570
V
4.900
5.000
5.100
V
-
-
0.2
%
-
-
1
%
-
12
15
mV
-
15
18
mV
-
20
25
mV
-
22
28
mV
-
23
30
mV
-
26
33
mV
-
28
35
mV
-
40
50
mV
-
1.1
1.3
V
0.7
-
-
A
-
5
0.008
10
0.04
mA
%/W
Rev.1.1 Aug.27, 2004
3/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Electrical Characteristics (Continued) (Under Operating Conditions)
F=120Hz,COUT=25uF Tantalum, IOUT=0.6A
AP1115-XXX
VIN=VOUT+3V
IO=10mA
Thermal Resistance Junction-to-Ambient (No
heat sink; No air flow)
SOT89: Control Circuitry/Power Transistor
Thermal Resistance Junction-to-Case
Ripple Rejection
Temperature Stability
θ JA
θ JC
-
SOT89
TO92
-
60
0.6
300
160
100
70
-
dB
%
o
C/W
o
C/W
Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are
measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead =
1/18” from the package.
Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 5W. Power dissipation is determined by the
input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full
input/output range.
Note3: Quiescent current is defined as the minimum output current required to maintain regulation. At 12V input/output differential the
device is guaranteed to regulate if the output current is greater than 10mA.
„ Marking Information
Identification Code
Date Code
Month: A~L
Year: 0~9
XX
XX X
1
2
3
Output
version
ADJ
1.5V
1.8V
2.5V
2.8V
3.0V
3.3V
3.5V
5.0V
Identification Code
( See the table )
Blank: normal
L: Lead Free Package
SOT89-3
Part Number
AP1115A
AP1115B
JO
JP
JQ
JR
JC
JM
JS
JK
JT
JU
JV
JW
JX
JD
JN
JY
JL
JZ
(Top View)
Part Number: AP1115
1115
A: A version
B: B version
X XX
Output voltage
Blank: ADJ
15:1.5V
18:1.8V
25:2.5V
28:2.8V
30:3.0V
33:3.3V
35:3.5V
50:5.0V
Y WW X X
1
2
3
Blank: normal
L: Lead Free Package
Internal code: Blank or A~Z
Xth Week: 01~52
Year: "1"=2001
"2"=2002
TO92
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Aug.27, 2004
4/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Typical Performance Characteristics
2. 0
0.20
Output Voltage Deviation (%)
1. 8
1. 6
Dropout Voltage (V)
1. 4
1. 2
0
I load=600mA
-0.20
Tj = 25 oC
1. 0
-0.40
0. 8
Tj = 125 oC
0. 6
-0.80
0. 4
0. 2
0
0
200
100
300
400
Output Current (mA)
500
-1
600
-25
Dropout Voltage vs Output Current
0
25
50
Temperature ( oC)
75
100
125
Load Regulation vs Temperature
2
1
0.8
1
Output Voltage Deviation (%)
Output Voltage Change (%)
1.5
0. 5
0
-0.5
-1
-1.5
-2
-50
-25
0
25
50
Temperature ( oC)
75
100
125
150
0.6
0.4
0.2
0
2
4
7.5
Load Current (A) Output Voltage Deviation (mV)
Output Voltage Deviation (mV) Input Voltage (V)
Percent Change in Output Voltage vs Temperature
Cin=1uF
Cout=10uF Tantalum
6.5
5.5
40
20
0
-20
-40
0
20
40
60
80
100 120 140 160 180 200
TIME (us)
Line Transient Response
6
8
10
Input Voltage (V)
12
Line Regulation
30
C in = 1uF
C out = 10 uF Tantalum
Preload = 100mA
20
10
0
-10
-20
2
1
0
-1
0
10
20
30
40
50
TIME (us)
60
70
80
90
100
Load Transient Response
Anachip Corp.
www.anachip.com.tw
Rev.1.1 Aug.27, 2004
5/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
„ Package Information
(1) Package Type: SOT89-3L
1.7
HE
E
2.7
D1
1.3
L
1.9
0.4
1.5
0.9
Land Pattern Recommendation (Unit: mm)
e1
e
50(2x)
0
8 (2x)
A
D
c
b
b
b1
Symbol
A
b
b1
C
D
D1
e
e1
E
HE
L
Dimensions In Millimeters
Min.
1.40
0.36
0.41
0.35
4.40
1.40
2.90
1.45
2.35
3.94
0.80
Nom.
1.50
0.42
0.47
0.39
4.50
1.60
3.00
1.50
2.48
-
Max.
1.60
0.48
0.53
0.43
4.60
1.75
3.10
1.55
2.60
4.25
1.20
Anachip Corp.
www.anachip.com.tw
Dimensions In Inches
Min.
0.055
0.014
0.016
0.014
0.173
0.055
0.114
0.057
0.093
0.155
0.031
Nom.
0.059
0.016
0.043
0.015
0.177
0.062
0.118
0.059
0.098
-
Max.
0.063
0.018
0.051
0.017
0.181
0.069
0.122
0.061
0.102
0.167
0.047
Rev.1.1 Aug.18, 2004
6/7
AP1115
0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator
(2) Package Type: TO92-3L
A1
A
b
b1
b
D
e
E
Symbol
A
A1
b
b1
D
E
L
e
L
Dimensions In Millimeters
Min.
Nom.
Max.
3.302
3.556
3.810
1.016
0.330
0.381
0.432
0.406
0.457
0.506
4.445
4.572
4.699
4.445
4.572
4.699
13.00
15.50
1.150
1.270
1.390
Anachip Corp.
www.anachip.com.tw
Dimensions In Inches
Min.
Nom.
Max.
0.130
0.140
0.150
0.040
0.013
0.015
0.017
0.016
0.018
0.020
0.175
0.180
0.185
0.175
0.180
0.185
0.512
0.610
0.045
0.050
0.055
Rev.1.1 Aug.27, 2004
7/7
Similar pages