ETC1 FDC60-48S15 60 watts output power Datasheet

• 60 WATTS OUTPUT POWER
• 2:1 WIDE INPUT VOLTAGE RANGE
• DESIGN MEET SAFETY STANDARD
• SIX-SIDED CONTINUOUS SHIELD
• HIGH EFFICIENCY UP TO 90%
• 3.94” X 2.76” X 0.75” PACKAGE
• FIXED SWITCHING FREQUENCY
The FDC60 series offer 60 watts of output power from a 3.94 x 2.76 x 0.75 inch package.
The FDC60 series have 2:1 wide input voltage of 9-18, 18-36 and 36-75VDC. The FDC60
features 1600VDC of isolation, short-circuit and over-voltage protection, as well as six
sided shielding. Designed meets the safety of EN60950 and UL1950. All models are
particularly suited to telecommunications, industrial, mobile telecom and test equipment
applications.
T E C H N I C A L S P E C I F I C AT I O N
All specifications are typical at nominal input, full load and 25ºC otherwise noted
GENERAL SPECIFICATIONS
OUTPUT SPECIFICATIONS
Output power
60 Watts max
Voltage accuracy
Full load and nominal Vin
± 2%
Voltage adjustability
± 10%
Minimum load (Note 1)
FDC60-XXD3305 3.3V output
Others
Line regulation
LL to HL at Full Load
Load regulation
10% to 100% FL
20MHz bandwidth
1600VDC, min
Isolation resistance
10 ohms, min
9
Isolation capacitance
1000pF, max
± 0.5%
Switching frequency
200KHz, typ
± 0.5%
Design meet safety standard
UL1950, EN60950
Nickel-coated copper
1%/p-p of Vout max
Base material
Non-conductive black plastic
I0.02% / ºC, max
Transient response recovery time 25% load step change
3.3V output
Over voltage protection 5V output
Zener diode clamp
12V output
15V output
500uS
3.9V
6.2V
15V
18V
Hiccup, automatics recovery
Potting material
Epoxy (UL94-V0)
3.94 X 2.76 X 0.75 Inches
(100.2 X 70.0 X 19.0 mm)
Dimensions
Weight
280g (9.86oz)
1.533 x 106 hrs
MTBF (Note 4)
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
INPUT SPECIFICATIONS
Input voltage range
Isolation voltage
Case material
Temperature coefficient
Short circuit protection
See table
± 5%
Cross regulation (Note 2)
Ripple and noise
800mA, min
10% of FL
Efficiency
12V nominal input
24V nominal input
48V nominal input
Input filter
9 – 18VDC
18 – 36VDC
36 – 75VDC
Pi type
Maximum case temperature
+95ºC
Storage temperature range
-25ºC ~ +100ºC
Thermal impedance
5.2ºC/watt
36VDC
50VDC
100VDC
Thermal shock
Input reflected ripple (Note 3) Nominal Vin and full load
40mAp-p
Relative humidity
Start up time
25mS typ
EMC CHARACTERISTICS
Input surge voltage
100mS max
12V input
24V input
48V input
Nominal Vin and constant resistor load
Remote ON/OFF
Remote off input current
DC-DC ON
DC-DC OFF
Nominal input
Open or 3.5V < Vr < 12V
Short or 0V < Vr < 1.2V
30mA
-25ºC ~ +71ºC (with derating)
MIL-STD-810D
Vibration
Conducted emissions
10~55Hz, 2G, 30minutes along X,Y and Z
5% to 95% RH
EN55022
Level A
Radiated emissions
EN55022
Conducted immunity
EN61000-4-6
Perf. Criteria2
Level A
Radiated immunity
EN61000-4-3
Perf. Criteria2
Surge
EN61000-4-5
Perf. Criteria2
Fast transient
EN61000-4-4
Perf. Criteria2
ESD
EN61000-4-2
Perf. Criteria2
(6)
(7)
Model
Number
Input
Range
Output
Voltage
Output
Current
Input
(5)
Current
Eff
(%)
Capacitor
Load max
FDC60-12S33
FDC60-12S05
FDC60-12S12
FDC60-12S15
FDC60-12D05
FDC60-12D12
FDC60-12D15
FDC60-12D3305
FDC60-24S33
FDC60-24S05
FDC60-24S12
FDC60-24S15
FDC60-24D05
FDC60-24D12
FDC60-24D15
FDC60-24D3305
FDC60-48S33
FDC60-48S05
FDC60-48S12
FDC60-48S15
FDC60-48D05
FDC60-48D12
FDC60-48D15
FDC60-48D3305
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
3.3 / 5VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
3.3 / 5VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
± 5 VDC
± 12 VDC
± 15 VDC
3.3 / 5VDC
15A
12A
5A
4A
+10 / -2A
± 2.5A
± 2A
6 / 6A
15A
12A
5A
4A
+10 / -2A
± 2.5A
± 2A
6 / 6A
15A
12A
5A
4A
+10 / -2A
± 2.5A
± 2A
6 / 6A
5430mA
6330mA
6250mA
6250mA
6500mA
6250mA
6250mA
5770mA
2750mA
3090mA
2980mA
2940mA
3130mA
3050mA
3010mA
2700mA
1310mA
1520mA
1470mA
1450mA
1540mA
1450mA
1450mA
1310mA
80
83
84
84
81
84
84
76
79
85
88
89
84
86
87
81
83
86
89
90
85
90
90
83
38700uF
20400uF
3550uF
2300uF
17000 / 3400uF
± 900uF
± 600uF
16000 / 10200uF
38700uF
20400uF
3550uF
2300uF
17000 / 3400uF
± 900uF
± 600uF
16000 / 10200uF
38700uF
20400uF
3550uF
2300uF
17000 / 3400uF
± 900uF
± 600uF
16000 / 10200uF
Note
1.
2.
3.
4.
5.
6.
7.
EXTERNAL OUTPUT TRIMMING
The FDC60 series required a minimum 10% loading on the output to maintain specified
regulation. Operation under no-load condition will not damage these devices, however
they may not meet all listed specification.
Cross regulation:
Dual output—Asymmetrical load 25% to 100% full load
Simulated source impedance of 12uH. 12uH inductor in series with +Vin.
BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed
and controlled environment)
Maximum value at nominal input voltage and full load
Typical value at nominal input voltage and full load.
Test by minimum Vin and constant resistor load.
6
0.98
(25.0)
7
Bottom
View
1.00
(25.4)
2
8
9
3
Mounting inserts: #4-40
0.39
(10.0)
4(4) [4]
10
0.30
(7.6)
3.25 (82.6)
RD
6(6) [6]
2.76(70.0)
0.39 0.39 0.39
(10.0) (10.0) (10.0)
1.00
(25.4)
1
5
TRIM DOWN
4(4) [4]
RU
0.39 0.39 0.39 0.39 0.39 0.39
(10.0) (10.0) (10.0) (10.0) (10.0) (10.0)
4
1.00
(25.4)
TRIM UP
7(9) [7]
0.05 (1.3)
3.94 (100.2)
1.00
(25.4)
Output can be externally trimmed by
using the method shown below.
( ) for dual output trim
[ ] XXD3305 only trim 3.3V
0.32
(8.0)
1. All dimensions in Inches (mm)
2. Pin Pitch tolerance ±0.014(0.35)
0.75
(19.0)
PIN CONNECTION
PIN
1
2
3
4
5
SINGLE
DUAL
+ INPUT + INPUT
- INPUT
- INPUT
CTRL
CTRL
TRIM
TRIM
+OUTPUT +OUTPUT
D3305
PIN
+ INPUT
- INPUT
6
7
8
9
10
CTRL
TRIM
+3.3V
SINGLE
DUAL
+OUTPUT +OUTPUT
- OUTPUT
COM
- OUTPUT
COM
NO PIN - OUTPUT
NO PIN - OUTPUT
D3305
+3.3V
COM
COM
+ 5V
+ 5V
Similar pages