ON CAT5171 256â position i2c compatible digital potentiometer (pot) Datasheet

CAT5171
256‐position I2C Compatible
Digital Potentiometer (POT)
The CA5171 is a 256-position digital linear taper potentiometer
ideally suited for replacing mechanical potentiometers and variable
resistors.
The wiper settings are controlled through an I2C-compatible digital
interface. Upon power-up, the wiper assumes a midscale position and
may be repositioned anytime after the power is stable. The device can
be programmed to reset the wiper position to midscale or to go to a
shutdown state during operation. An address input pin, AD0, allows
the connection of two devices onto the same I2C bus.
The CAT5171 operates from 2.7 V to 5.5 V, while consuming less
than 2 mA. This low operating current, combined with a small package
footprint, makes the CAT5171 ideal for battery-powered portable
applications.
The CAT5171, designed as a pin for pin replacement for the
AD5245, is offered in the 8-lead SOT23 package and operates over the
−40C to +85C industrial temperature range.
http://onsemi.com
SOT23−8
TP, TB SUFFIX
CASE 527AK
MARKING DIAGRAM
Features










256-position
End-to-End Resistance: 50 kW, 100 kW
I2C Compatible Interface
Power-on Preset to Midscale
Single Supply 2.7 V to 5.5 V
Low Temperature Coefficient 100 ppm/C
Low Power, IDD 2 mA max
Wide Operating Temperature −40C to +85C
SOT−23 8-lead (2.9 mm  3 mm) Package
These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
Typical Applications
 Potentiometer Replacement
 Transducer Adjustment of Pressure, Temperature, Position,


Chemical, and Optical Sensors
RF Amplifier Biasing
Gain Control and Offset Adjustment
AFYM
AGYM
1
1
AF = 50 kW
AG = 100 kW
Y = Production Year
Y = (Last Digit)
M = Production Month
M = (1 − 9, A, B, C)
PIN CONNECTIONS
W
A
1
B
VDD
GND
AD0
SCL
SDA
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
 Semiconductor Components Industries, LLC, 2013
July, 2013 − Rev. 2
1
Publication Order Number:
CAT5171/D
CAT5171
VDD
A
SCL
I2C Interface
and
Control
SDA
AD0
Power On
Midscale
W
B
GND
Figure 1. Functional Block Diagram
Table 1. ORDERING INFORMATION
Part Number
Resistance
CAT5171TBI−50GT3
50 kW
CAT5171TBI−00GT3
100 kW
Temperature Range
Package
Shipping†
−40C to 85C
SOT−23−8
(Pb-Free)
3000/Tape & Reel
3000/Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
1. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com.
Table 2. PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1
W
2
VDD
Positive Power Supply
3
GND
Digital Ground
4
SCL
Serial Clock Input
5
SDA
Serial Data Input
6
AD0
I2C Address bit 0 input
7
B
Bottom Terminal of resistive element
8
A
Top Terminal of resistive element
Resistor’s Wiper Terminal
Table 3. ABSOLUTE MAXIMUM RATINGS (Note 2)
Rating
VDD to GND
Value
Unit
−0.3 to 6.5
V
VA, VB, VW to GND
VDD
IMAX
20
mA
0 to 6.5
V
−40 to +85
C
150
C
−65 to +150
C
300
C
Digital Inputs and Output Voltage to GND
Operating Temperature Range
Maximum Junction Temperature (TJMAX)
Storage Temperature
Lead Temperature (Soldering, 10 sec)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
2. Maximum terminal current is bounded by the maximum current handling of the switches, maximum power dissipation of the package, and
maximum applied voltage across any two of the A, B, and W terminals at a given resistance.
http://onsemi.com
2
CAT5171
Table 4. ELECTRICAL CHARACTERISTICS: 50 kW and 100 kW Versions
VDD = 2.7 V to 5.5 V; VA = VDD; VB = 0 V; –40C < TA < +85C; unless otherwise noted.
Test Conditions
Symbol
Min
Typ
(Note 3)
Max
Unit
Resistor Differential Nonlinearity (Note 4)
RWB, VA = no connection
R−DNL
−1
0.1
+1
LSB
Resistor Integral Nonlinearity (Note 4)
0.4
+2
LSB
Parameter
DC CHARACTERISTICS — RHEOSTAT MODE
RWB, VA = no connection
R−INL
−2
Nominal Resistor Tolerance (Note 5)
TA = 25C
nRAB
−20
Resistance Temperature Coefficient
VAB = VDD, Wiper = no connection
nRAB/nT
VDD = 5 V, IW = 3 mA
RW
Wiper Resistance
+20
100
VDD = 3 V, IW = 3 mA
%
ppm/C
50
120
100
250
W
DC CHARACTERISTICS — POTENTIOMETER DIVIDER MODE
N
Resolution
8
Bits
LSB
Differential Nonlinearity (Note 6)
DNL
−1
0.1
+1
Integral Nonlinearity (Note 6)
INL
−1
0.4
+1
100
LSB
Voltage Divider Temperature Coefficient
Code = 0x80
nVW/nT
ppm/C
Full-Scale Error
Code = 0xFF
VWFSE
−3
−1
0
LSB
Zero-Scale Error
Code = 0x00
VWZSE
0
1
3
LSB
VA,B,W
GND
VDD
V
RESISTOR TERMINALS
Voltage Range (Note 7)
Capacitance (Note 8) A, B
f = 1 MHz, measured to GND,
Code = 0 x 80
CA,B
45
pF
Capacitance (Note 8) W
f = 1 MHz, measured to GND,
Code = 0 x 80
CW
60
pF
VA = VB = VDD/2
ICM
1
nA
Input Logic High
VDD = 5 V
VIH
Input Logic Low
VDD = 5 V
VIL
Input Logic High
VDD = 3 V
VIH
VDD = 3 V
VIL
0.3VDD
V
VIN = 0 V or 5 V
IIL
1
mA
5.5
V
Common-Mode Leakage (Note 8)
DIGITAL INPUTS
Input Logic Low
Input Current
0.7 x VDD
V
0.3VDD
0.7 x VDD
V
V
POWER SUPPLIES
VDD RANGE
Power Supply Range
Supply Current
Power Dissipation (Note 8)
Power Supply Sensitivity
2.7
VIH = 5 V or VIL = 0 V
IDD
2
mA
VIH = 5 V or VIL = 0 V, VDD = 5 V
PDISS
0.3
0.2
mW
nVDD = +5 V 10%, Code = Midscale
PSS
0.05
%/%
DYNAMIC CHARACTERISTICS (Notes 8 and 10)
Bandwidth –3 dB
Total Harmonic Distortion
VW Settling Time (50 kW/100 kW)
RAB = 50 kW / 100 kW, Code = 0x80
BW
100/40
kHz
VA =1 V rms, VB = 0 V,
f = 1 kHz, RAB = 10 kW
THDW
0.05
%
VA = 5 V, VB = 0 V, 1 LSB error band
tS
2
ms
3. Typical specifications represent average readings at +25C and VDD = 5 V.
4. Resistor position nonlinearity error R−INL is the deviation from an ideal value measured between the maximum resistance and the
minimum resistance wiper positions. R−DNL measures the relative step change from ideal between successive tap positions. Parts are
guaranteed monotonic.
5. VAB = VDD, Wiper (VW) = no connect.
6. INL and DNL are measured at VW with the digital potentiometer configured as a potentiometer divider similar to a voltage output D/A
converter. VA = VDD and VB = 0 V. DNL specification limits of 1 LSB maximum are guaranteed monotonic operating conditions.
7. Resistor terminals A, B, W have no limitations on polarity with respect to each other.
8. Guaranteed by design and not subject to production test.
9. Maximum terminal current is bounded by the maximum current handling of the switches, maximum power dissipation of the package, and
maximum applied voltage across any two of the A, B, and W terminals at a given resistance.
10. All dynamic characteristics use VDD = 5 V.
http://onsemi.com
3
CAT5171
Table 5. CAPACITANCE
TA = 25C, f = 1.0 MHz, VDD = 5 V
Test
Symbol
CI/O
(Note 11)
Input/Output Capacitance (SDA, SCL)
Conditions
Max
Units
VI/O = 0V
8
pF
Max
Units
Table 6. POWER UP TIMING (Notes 11 and 12)
Parameter
Symbol
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
Max
Units
Wiper Response Time After Power Supply Stable
50
ms
Wiper Response Time: SCL falling edge after last bit of wiper position data byte to
wiper change
20
ms
Max
Units
400
kHz
11. This parameter is tested initially and after a design or process change that affects the parameter.
12. tPUR and t PUW are delays required from the time VCC is stable until the specified operation can be initiated.
Table 7. DIGITAL POTENTIOMETER TIMING
Symbol
tWRPO
tWR
Parameter
Min
Table 8. A.C. CHARACTERISTICS
VDD = +2.7 V to +5.5 V, −40C to +85C unless otherwise specified.
Parameter
Symbol
Min
Typ
fSCL
Clock Frequency
tHIGH
Clock High Period
600
ns
tLOW
Clock Low Period
1300
ns
tSU:STA
Start Condition Setup Time (for a Repeated Start Condition)
600
ns
tHD:STA
Start Condition Hold Time
600
ns
tSU:DAT
Data in Setup Time
100
ns
tHD:DAT
Data in Hold Time
0
ns
tSU:STO
Stop Condition Setup Time
600
ns
Time the bus must be free before a new transmission can start
1300
ns
tBUF
tR
SDA and SCL Rise Time
300
ns
tF
SDA and SCL Fall Time
300
ns
tDH
Data Out Hold Time
100
ns
TI
Noise Suppression Time Constant at SCL, SDA Inputs
50
ns
tAA
SCL Low to SDA Data Out and ACK Out
1
ms
http://onsemi.com
4
CAT5171
TYPICAL CHARACTERISTICS
0.03
0.1
0.02
0
DNL
ERROR (LSB)
ERROR (LSB)
0.01
0
−0.01
−0.02
−0.1
INL
−0.2
−0.3
−0.03
−0.4
−0.04
−0.05
0
32
64
96
128
160
192
224
−0.5
256
0
32
64
96
128
160
192
TAP
TAP
Figure 2. Differential Non−Linearity,
VDD = 5.6 V
Figure 3. Integral Non−Linearity,
VDD = 5.6 V
120
6
100
5
224 256
5.6 V
VDD = 2.6 V
4.0 V
Vw (V)
60
3.3 V
3
40
3.3 V
2
20
0
5.0 V
4
5.6 V
4.0 V
0
50
100
VDD = 2.6 V
1
150
200
0
250
0
52
104
156
TAP
TAP
Figure 4. Wiper Resistance at Room
Temperature
Figure 5. Wiper Voltage
400
350
T = 90C
300
ISB (nA)
Rw (W)
80
T = −45C
250
T = 25C
200
150
100
2
3
4
5
VDD (V)
Figure 6. Standby Current
http://onsemi.com
5
6
208
260
CAT5171
TYPICAL CHARACTERISTICS
102.15
0.4
102.10
102.05
0.2
D (%)
R (kW)
102.00
101.95
101.90
0
101.85
101.80
−0.2
−50
−20
10
40
70
101.75
−50
100
−20
10
40
70
TEMPERATURE (C)
TEMPERATURE (C)
Figure 7. Change in End−to−End Resistance
Figure 8. End−to−End Resistance vs.
Temperature
0
100
30
−6
25
VDD = 5 V
PSRR (dB)
A (dB)
−12
VDD = 3 V
−18
−24
−30
−36
20
VDD = 5 V
15
VDD = 3 V
10
5
1
10
100
1000
0
1
10
100
f (KHz)
f (KHz)
Figure 9. Gain vs. Bandwidth (Tap 0x80)
Figure 10. PSRR
http://onsemi.com
6
1000
CAT5171
BASIC OPERATION
stable, the wiper may be repositioned via the I2C compatible
interface.
The CAT5171 is a 256-position digitally controlled
potentiometer. When power is first applied, the wiper
assumes a mid-scale position. Once the power supply is
PROGRAMMING: VARIABLE RESISTOR
Rheostat Mode
and RW is the wiper resistance contributed by the on
resistance of the internal switch.
In summary, if RAB = 100 kW and the A terminal is open
circuited, the following output resistance RWB will be set for
the indicated Wiper register codes:
The resistance between terminals A and B, RAB, has a
nominal value of 50 kW or 100 kW and has 256 contact
points accessed by the wiper terminal, plus the B terminal
contact. Data in the 8-bit Wiper register is decoded to select
one of these 256 possible settings.
The wiper’s first connection is at the B terminal,
corresponding to control position 0x00. Ideally this would
present a 0 W between the Wiper and B, but just as with a
mechanical rheostat there is a small amount of contact
resistance to be considered, there is a wiper resistance
comprised of the RON of the FET switch connecting the
wiper output with its respective contact point. In CAT5171
this ‘contact’ resistance is typically 50 W. Thus a connection
setting of 0x00 yields a minimum resistance of 50 W
between terminals W and B.
For a 100 kW device, the second connection, or the first tap
point, corresponds to 441 W (RWB = RAB/256 + RW = 390.6
+ 50 W) for data 0x01. The third connection is the next tap
point, is 831 W (2 x 390.6 + 50 W) for data 0x02, and so on.
Figure 11 shows a simplified equivalent circuit where the
last resistor string will not be accessed; therefore, there is
1 LSB less of the nominal resistance at full scale in addition
to the wiper resistance.
Table 9. CODES AND CORRESPONDING RWB
RESISTANCE FOR RAB = 100 kW, VDD = 5 V
RWB (W)
Output State
255
99,559
Full Scale (RAB – 1 LSB + RW)
128
50,050
Midscale
1
441
1 LSB
0
50
Zero Scale
(Wiper Contact Resistance)
Be aware that in the zero-scale position, the wiper
resistance of 50 W is still present. Current flow between W
and B in this condition should be limited to a maximum
pulsed current of no more than 20 mA. Failure to heed this
restriction can cause degradation or possible destruction of
the internal switch contact.
Similar to the mechanical potentiometer, the resistance of
the digital POT between the wiper W and terminal A also
produces a digitally controlled complementary resistance
RWA. When these terminals are used, the B terminal can be
opened. Setting the resistance value for RWA starts at a
maximum value of resistance and decreases as the data
loaded in the latch increases in value. The general equation
for this operation is
A
RS
RS
Wiper
Register
and
Decoder
D (Dec.)
R WA(D) + 256 * D R AB ) R W
256
(eq. 2)
For RAB = 100 kW and the B terminal open circuited, the
following output resistance RWA will be set for the indicated
Wiper register codes.
RS
W
Table 10. CODES AND CORRESPONDING RWA
RESISTANCE FOR RAB = 100 kW, VDD = 5 V
RS
B
Figure 11. CAT5171 Equivalent Digital POT Circuit
The equation for determining the digitally programmed
output resistance between W and B is
R WB + D R AB ) R W
256
(eq. 1)
D (Dec.)
RWA (W)
Output State
255
441
Full Scale
128
50,050
Midscale
1
99,659
1 LSB
0
100,050
Zero Scale
Typical device to device resistance matching is lot
dependent and may vary by up to 20%.
where D is the decimal equivalent of the binary code loaded
in the 8-bit Wiper register, RAB is the end-to-end resistance,
http://onsemi.com
7
CAT5171
ESD Protection
Power-up Sequence
Digital
Input
Because ESD protection diodes limit the voltage
compliance at terminals A, B, and W (see Figure 12), it is
recommended that VDD/GND be powered before applying
any voltage to terminals A, B, and W. The ideal power−up
sequence is: GND, VDD, digital inputs, and then VA/B/W. The
order of powering VA, VB, VW, and the digital inputs is not
important as long as they are powered after VDD/GND.
LOGIC
GND
Power Supply Bypassing
Good design practice employs compact, minimum lead
length layout design. Leads should be as direct as possible.
It is also recommended to bypass the power supplies with
quality low ESR Ceramic chip capacitors of 0.01 mF to
0.1 mF. Low ESR 1 mF to 10 mF tantalum or electrolytic
capacitors can also be applied at the supplies to suppress
transient disturbances and low frequency ripple. As a further
precaution digital ground should be joined remotely to the
analog ground at one point to minimize the ground bounce.
W, A, B
Potentiometer
GND
VDD
Figure 12. ESD Protection Networks
VDD
C3
10 mF
Terminal Voltage Operating Range
The CAT5171 VDD and GND power supply define the
limits for proper 3-terminal digital potentiometer operation.
Signals or potentials applied to terminals A, B or the wiper
must remain inside the span of VDD and GND. Signals
which attempt to go outside these boundaries will be
clamped by the internal forward biased diodes.
+
C1
0.1 mF
CAT5171
GND
Figure 14. Power Supply Bypassing
VDD
W, A, B
CAT5171
LOGIC
GND
Figure 13.
http://onsemi.com
8
CAT5171
I2C BUS PROTOCOL
The following defines the features of the I2C bus protocol:
1. Data transfer may be initiated only when the bus is
not busy.
2. During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock is high
will be interpreted as a START or STOP condition.
is hard-wired to the AD0 pin to establish the device’s
address.
After the Master sends a START condition and the slave
address byte, the CAT5171 monitors the bus and responds
with an acknowledge (on the SDA line) when its address
matches the transmitted slave address.
Acknowledge
The device controlling the transfer is a master, typically a
processor or controller, and the device being controlled is the
slave. The master will always initiate data transfers and
provide the clock for both transmit and receive operations.
Therefore, the CAT5171 will be considered a slave device
in all applications.
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledging
device pulls down the SDA line during the ninth clock cycle,
signaling that it received the 8 bits of data.
The CAT5171 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8-bit
byte.
When the CAT5171 is in a READ mode it transmits 8 bits
of data, releases the SDA line, and monitors the line for an
acknowledge. Once it receives this acknowledge, the
CAT5171 will continue to transmit data. If no acknowledge
is sent by the Master, the device terminates data transmission
and waits for a STOP condition.
START Condition
The START condition precedes all commands to the
device, and is defined as a high to low transition of SDA
when SCL is high. The CAT5171 monitors the SDA and
SCL lines and will not respond until this condition is met.
STOP Condition
A low to high transition of SDA when SCL is high
determines the STOP condition. All operations must end
with a STOP condition.
Write Operation
In the Write mode, the Master device sends the START
condition and the slave address information to the Slave
device. After the Slave generates an acknowledge, the
Master sends the instruction byte. After receiving another
acknowledge from the Slave, the Master device transmits
the data to be written into the wiper register. The CAT5171
acknowledges once more and the Master generates the
STOP condition.
Device Addressing
The bus Master begins a transmission by sending a
START condition. The Master then sends the address of the
particular slave device it is requesting. The six most
significant bits of the 8-bit slave address are fixed as 010110
for the CAT5171. The next bit (AD0) is the device least
significant address bit and defines which device the Master
is accessing. Up to two devices may be individually
addressed by the system. Typically, +5 V (VDD) or ground
tF
tHIGH
tLOW
tR
tLOW
SCL
tSU:STA
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
SDA IN
tAA
tDH
SDA OUT
Figure 15. Bus Timing Diagram
http://onsemi.com
9
tBUF
CAT5171
SDA
SCL
START CONDITION
STOP CONDITION
Figure 16. Start/Stop Condition
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
ACKNOWLEDGE
Figure 17. Acknowledge Condition
http://onsemi.com
10
CAT5171
INSTRUCTION AND REGISTER DESCRIPTION
Slave Address Byte
power-up, the wiper is set to midscale and may be
repositioned anytime after the power has become stable.
The first byte sent to the CAT5171 from the
master/processor is called the Slave Address Byte. The most
significant six bits of the slave address are a device type
identifier. For the CAT5171, these bits are fixed at 010110.
The next bit, AD0, is the first bit of the internal slave
address and must match the physical device address which
is defined by the state of the AD0 input pin for the CAT5171
to successfully continue the command sequence. Only the
device which slave address matches the incoming device
address sent by the master executes the instruction. The AD0
input can be actively driven by CMOS input signals or tied
to the supply voltage or ground.
The next bit, R/W, indicates whether this command
corresponds to a Write or Read instruction. To write into the
Wiper control register, R/W bit is set to a logic low; while a
read from the wiper register is done with the bit high.
Instructions
Write and Read instructions are respectively three and two
bytes in length. The basic sequence of the two instructions
is illustrated in Table 11 and 12.
In write mode, the second byte is the instruction byte. The
first bit (MSB) of the instruction byte is a don’t care. The
second MSB, RS, is the midscale reset. A logic high on this
bit moves the wiper to the center tap. The third MSB, SD, is
a shutdown bit. A logic high causes an open circuit at
terminal A, and short the wiper terminal W to terminal B.
The “shutdown” operation does not change the contents of
the wiper register. When the shutdown bit, SD, goes back to
a logic low, the previous wiper position is restored. Also
during shutdown, new settings can be programmed. As soon
as the device is returned from shutdown, the wiper position
is set according to the wiper register value.
Wiper Control
The CAT5171 contains one 8-bit Wiper Control Register
(WCR). The Wiper Control Register output is decoded to
select one of 256 switches along its resistor array. The
contents of the WCR may be written by the host via Write
instruction.
The Wiper Control Register is a volatile register that loses
its contents when the CAT5171 is powered-down. Upon
Two CAT5171 on a Single Bus
When needed, it is possible to connect two CAT5171
potentiometers on the same I2C bus and be able to address
each one independently. Each device can be set to a unique
address by using the AD0 input pin. One device AD0 pin is
connected to ground, and the other device AD0 pin is tied to
the supply voltage.
Table 11. Write
S
0
1
0
1
1
0
AD0
W
A
X
RS
Slave Address Byte
SD
X
X
X
X
X
A
D7
D6
D5
Instruction Byte
D4
D3
D2
D1
D0
D2
D1
D0
A
P
Data Byte
SDA
0 1
S
T
A
R
T
0
1 1
0
AD0
X
R/W
RS
SD
D6
D7
X X X X X
A
C
K
D5
D4
D3
A S
C T
K O
P
A
C
K
Instruction Byte
Slave Address Byte
Data Byte
Table 12. READ
S
0
1
0
1
1
0
AD0
R
A
D7
D6
D5
Slave Address Byte
SDA
S
T
A
R
T
0
1 0
1 1
0
D4
D3
D2
D1
D0
D2
D1
D0
A
P
N
A
C
K
S
T
O
P
Data Byte
D7
AD0 R/W
D6
D5
D4
D3
A
C
K
Data Byte
Slave Address Byte
Legend
W = Write (bit is 0 for Write instruction)
RS = When the bit is 1, the wiper position is moved
to mid-scale 0x80
SD = Shut Down:
0: normal operation
1: wiper is parked at B terminal and terminal A
is open circuit.
X = Don’t Care
S = Start
P = Stop
A = Acknowledge
AD0 = Address bit 0, needed when using two
potentiometers on the same I2C bus.
D = Data bit
R = Read (bit is 1 for Read instruction)
http://onsemi.com
11
CAT5171
PACKAGE DIMENSIONS
SOT−23, 8 Lead
CASE 527AK
ISSUE A
E1
e
SYMBOL
MIN
A
0.90
A1
0.00
A2
0.90
A3
0.60
0.80
b
0.28
0.38
c
0.08
0.22
E
b
1.45
0.15
1.10
1.30
2.90 BSC
E
2.80 BSC
E1
1.60 BSC
0.65 BSC
L
TOP VIEW
MAX
D
e
PIN #1 IDENTIFICATION
NOM
0.45
0.30
L1
0.60
0.60 REF
L2
0.25 REF
θ
0°
8°
D
A2
A
q
A3
c
L1
A1
SIDE VIEW
L
L2
END VIEW
Notes:
(1) All dimensions in millimeters. Angles in degrees.
(2) Complies with JEDEC standard MO-178.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT5171/D
Similar pages