AD AD8012ARM-REEL Dual 350 mhz low power amplifier Datasheet

Dual 350 MHz
Low Power Amplifier
AD8012*
FEATURES
Low Power
1.7 mA/Amplifier Supply Current
Fully Specified for 5 V and +5 V Supplies
High Output Current, 125 mA
High Speed
350 MHz, –3 dB Bandwidth (G = +1)
150 MHz, –3 dB Bandwidth (G = +2)
2,250 V/s Slew Rate
20 ns Settling Time to 0.1%
Low Distortion
–72 dBc Worst Harmonic @ 500 kHz, RL = 100 –66 dBc Worst Harmonic @ 5 MHz, RL = 1 k
Good Video Specifications (RL = 1 k, G = +2)
0.02% Differential Gain Error
0.06 Differential Phase Error
Gain Flatness 0.1 dB to 40 MHz
60 ns Overdrive Recovery
Low Offset Voltage, 1.5 mV
Low Voltage Noise, 2.5 nV/√Hz
Available in 8-Lead SOIC and 8-Lead MSOP
FUNCTIONAL BLOCK DIAGRAM
OUT1
1
8 +VS
–IN1
2
7 OUT2
+IN1
3
6 –IN2
–VS
4
5 +IN2
AD8012
–40
G = +2
VOUT = 2V p-p
RF = 750
–50
DISTORTION – dBc
APPLICATIONS
XDSL, HDSL Line Drivers
ADC Buffers
Professional Cameras
CCD Imaging Systems
Ultrasound Equipment
Digital Cameras
–60
THIRD
–70
–80
SECOND
PRODUCT DESCRIPTION
The AD8012 is a dual, low power, current feedback amplifier
capable of providing 350 MHz bandwidth while using only
1.7 mA per amplifier. It is intended for use in high frequency,
wide dynamic range systems where low distortion and high
speed are essential and low power is critical.
With only 1.7 mA of supply current, the AD8012 also offers
exceptional ac specifications such as 20 ns settling time and
2,250 V/µs slew rate. The video specifications are 0.02% differential gain and 0.06 degree differential phase, excellent for such
a low power amplifier. In addition, the AD8012 has a low offset
of 1.5 mV.
–90
10
100
RL – Figure 1. Distortion vs. Load Resistance, VS = ± 5 V,
Frequency = 500 kHz
+VS
+
R1
+
AMP 1
RL = 100
OR
135
VREF
VIN
The AD8012 is well suited for any application that requires high
performance with minimal power.
The product is available in standard 8-lead SOIC or MSOP
packages and operates over the industrial temperature range
–40°C to +85°C.
1k
R2
VOUT
LINE
POWER
IN dB
–
Np:Ns
TRANSFORMER
–
–VS
Figure 2. Differential Drive Circuit for XDSL Applications
*Protected under U.S. Patent Number 5,537,079.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
AD8012–SPECIFICATIONS
DUAL SUPPLY (@ T = 25C, V = 5 V, G = +2, R = 100 , R = R
A
S
Parameter
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth
0.1 dB Bandwidth
Large Signal Bandwidth
Slew Rate
Rise and Fall Time
Settling Time
Overdrive Recovery
NOISE/HARMONIC PERFORMANCE
Distortion
Second Harmonic
Third Harmonic
Output IP3
IMD
Crosstalk
Input Voltage Noise
Input Current Noise
Differential Gain
Differential Phase
L
F
G
= 750 , unless otherwise noted.)
Conditions
Min
Typ
G = +1, VOUT < 0.4 V p-p, RL = 1 kΩ
G = +2, VOUT < 0.4 V p-p, RL = 1 kΩ
G = +2, VOUT < 0.4 V p-p, RL = 100 Ω
VOUT < 0.4 V p-p, RL = 1 kΩ/100 Ω
VOUT = 4 V p-p
VOUT = 4 V p-p
VOUT = 2 V p-p
0.1%, VOUT = 2 V p-p
0.02%, VOUT = 2 V p-p
2⫻ Overdrive
270
95
350
150
90
40/23
75
2,250
3
20
35
60
MHz
MHz
MHz
MHz
MHz
V/µs
ns
ns
ns
ns
–89/–73
–78/–62
–84/–72
–66/–52
30/40
–79/–77
–70
2.5
15
0.02/0.02
0.3/0.06
dBc
dBc
dBc
dBc
dBm
dBc
dB
nV/√Hz
pA/√Hz
%
Degrees
VOUT = 2 V p-p, G = +2
500 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 1 kΩ/100 Ω
500 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 1 kΩ/100 Ω
500 kHz, ∆f = 10 kHz, RL = 1 kΩ/100 Ω
500 kHz, ∆f = 10 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 100 Ω
f = 10 kHz
f = 10 kHz, +Input, –Input
f = 3.58 MHz, RL = 150 Ω/1 kΩ, G = +2
f = 3.58 MHz, RL = 150 Ω/1 kΩ, G = +2
DC PERFORMANCE
Input Offset Voltage
Open-Loop Transimpedance
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Bias Current
Common-Mode Rejection Ratio
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Resistance
Output Voltage Swing
Output Current
Short-Circuit Current
± 1.5
TMIN–TMAX
VOUT = ± 2 V, RL = 100 Ω
TMIN–TMAX
+Input
+Input
+Input, –Input
+Input, –Input, TMIN–TMAX
VCM = ± 2.5 V
240
200
Operating Range
Power Supply Rejection Ratio
Unit
mV
mV
kΩ
kΩ
–56
± 3.8
–60
± 4.1
kΩ
pF
µA
µA
dB
V
± 3.85
70
0.1
±4
125
500
Ω
V
mA
mA
POWER SUPPLY
Supply Current/Amp
1.7
TMIN–TMAX
Dual Supply
±4
±5
500
450
2.3
±3
G = +2
TMIN–TMAX
Max
± 1.5
–58
–60
± 12
± 15
1.8
1.9
± 6.0
mA
mA
V
dB
Specifications subject to change without notice.
–2–
REV. B
AD8012
SINGLE SUPPLY (@ T = 25C, V = +5 V, G = +2, R = 100 , R = R
A
S
Parameter
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth
0.1 dB Bandwidth
Large Signal Bandwidth
Slew Rate
Rise and Fall Time
Settling Time
Overdrive Recovery
NOISE/HARMONIC PERFORMANCE
Distortion
Second Harmonic
Third Harmonic
Output IP3
IMD
Crosstalk
Input Voltage Noise
Input Current Noise
Differential Gain
Differential Phase
L
F
G
= 750 , unless otherwise noted.)
Conditions
Min
Typ
G = +1, VOUT < 0.4 V p-p, RL = 1 kΩ
G = +2, VOUT < 0.4 V p-p, RL = 1 kΩ
G = +2, VOUT < 0.4 V p-p, RL = 100 Ω
VOUT < 0.4 V p-p, RL = 1 kΩ/100 Ω
VOUT = 2 V p-p
VOUT = 3 V p-p
VOUT = 2 V p-p
0.1%, VOUT = 2 V p-p
0.02%, VOUT = 2 V p-p
2⫻ Overdrive
220
90
300
140
85
43/24
60
1,200
2
25
40
60
MHz
MHz
MHz
MHz
MHz
V/µs
ns
ns
ns
ns
–87/–71
–77/–61
–89/–72
–78/–52
30/40
–77/–80
–70
2.5
15
dBc
dBc
dBc
dBc
dBm
dBc
dB
nV/√Hz
pA/√Hz
0.03/0.03
0.4/0.08
%
Degrees
VOUT = 2 V p-p, G = +2
500 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 1 kΩ/100 Ω
500 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 1 kΩ/100 Ω
500 kHz, RL = 1 kΩ/100 Ω
500 kHz, RL = 1 kΩ/100 Ω
5 MHz, RL = 100 Ω
f = 10 kHz
f = 10 kHz, +Input, –Input
Black Level Clamped to +2 V, f = 3.58 MHz
RL = 150 Ω/1 kΩ
RL = 150 Ω/1 kΩ
DC PERFORMANCE
Input Offset Voltage
Open-Loop Transimpedance
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Bias Current
Common-Mode Rejection Ratio
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Resistance
Output Voltage Swing
Output Current
Short-Circuit Current
±1
TMIN–TMAX
VOUT = 2 V p-p, RL = 100 Ω
TMIN–TMAX
+Input
+Input
+Input, –Input
+Input, –Input, TMIN–TMAX
VCM = 1.5 V to 3.5 V
200
150
Operating Range
Power Supply Rejection Ratio
REV. B
–60
1.2 to 3.8
1 to 4
50
0.1
0.9 to 4.2
100
500
Ω
V
mA
mA
3
–58
–3–
mV
mV
kΩ
kΩ
–56
1.5 to 3.5
1.55
Specifications subject to change without notice.
Unit
kΩ
pF
µA
µA
dB
V
POWER SUPPLY
Supply Current/Amp
TMIN–TMAX
Single Supply
±3
±4
400
450
2.3
±3
G = +2
TMIN–TMAX
Max
–60
± 12
± 15
1.75
1.85
12
mA
mA
V
dB
AD8012
2.0
MAXIMUM POWER DISSIPATION
MAXIMUM POWER DISSIPATION – W
The maximum power that can be safely dissipated by the AD8012
is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices
is determined by the glass transition temperature of the plastic,
approximately +150°C. Temporarily exceeding this limit may
cause a shift in parametric performance due to a change in the
stresses exerted on the die by the package. Exceeding a junction
temperature of +175°C for an extended period can result in
device failure.
The output stage of the AD8012 is designed for maximum load
current capability. As a result, shorting the output to common
can cause the AD8012 to source or sink 500 mA. To ensure
proper operation, it is necessary to observe the maximum power
derating curves. Direct connection of the output to either power
supply rail can destroy the device.
TJ = 150C
1.5
8-LEAD SOIC
PACKAGE
1.0
0.5
8-LEAD
MSOP
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70
AMBIENT TEMPERATURE – C
80 90
Figure 3. Plot of Maximum Power Dissipation vs.
Temperature for AD8012
Test Circuits
750
750
750
VOUT
RL
VIN
49.9
0.1F
0.1F
+
+
750
VIN
VOUT
RL
53.6
+VS
0.1F
10F
10F
0.1F
+
+
+VS
10F
10F
–VS
–VS
Test Circuit 1. Gain = +2
Test Circuit 2. Gain = –1
–4–
REV. B
AD8012
ABSOLUTE MAXIMUM RATINGS 1
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for device in free air at +25°C.
8-Lead SOIC Package: ␪JA = 155°C/W
8-Lead MSOP Package: ␪JA = 200°C/W
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V
Internal Power Dissipation2
SOIC Package (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 W
MSOP Package (RM) . . . . . . . . . . . . . . . . . . . . . . . . 0.6 W
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 2.5 V
Output Short-Circuit Duration
. . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range RM, R . . . . . . –65°C to +125°C
Operating Temperature Range (A Grade) . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300°C
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD8012 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Options
Branding
AD8012AR
AD8012AR-REEL
AD8012AR-REEL7
AD8012ARM
AD8012ARM-REEL
AD8012ARM-REEL7
AD8012ARMZ*
AD8012ARMZ-REEL*
AD8012ARMZ-REEL7*
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
8-Lead SOIC
13” Tape and Reel
7” Tape and Reel
8-Lead MSOP
13” Tape and Reel
7” Tape and Reel
8-Lead MSOP
13” Tape and Reel
7” Tape and Reel
R-8
R-8
R-8
RM-08
RM-08
RM-08
RM-08
RM-08
RM-08
H6A
H6A
H6A
H6A
H6A
H6A
*Z = Pb-free product.
REV. B
–5–
AD8012–Typical Performance Characteristics
20mV
1V
5ns
TPC 1. 100 mV Step Response; G = +2, VS = ±2.5 V or
±5 V, RL = 1 kΩ*
1V
TPC 4. 4 V Step Response; G = –1, VS = ± 5 V, RL = 1 kΩ
20mV
10ns
TPC 2. 4 V Step Response; G = +2, VS = ± 5 V, RL = 1 kΩ
20mV
10ns
5ns
TPC 5. 100 mV Step Response; G = +2, VS = ±2.5 V or
±5 V, RL = 100 Ω*
500mV
5ns
TPC 3. 100 mV Step Response; G = –1, VS = ± 2.5 V
or ±5 V, RL = 1 kΩ*
10ns
TPC 6. 2 V Step Response; G = +2, VS = ± 2.5 V, RL = 100 Ω
*VS = ± 2.5 V operation is identical to VS = +5 V single-supply operation.
–6–
REV. B
AD8012
1V
1V
10ns
TPC 7. 4 V Step Response; G = +2, VS = ± 5 V, RL = 100 Ω
10ns
TPC 10. 4 V Step Response; G = –1, VS = ± 5 V, RL = 100 Ω
–40
G = +2
VOUT = 2V p-p
RF = 750
DISTORTION – dBc
–50
–60
THIRD
–70
–80
SECOND
20mV
5ns
–90
TPC 8. 100 mV Step Response; G = –1, VS = ±2.5 V
or ±5 V, RL = 100 Ω*
10
100
RL – 1k
TPC 11. Distortion vs. Load Resistance; VS = ± 5 V,
Frequency = 500 kHz
–40
DISTORTION dBc
THIRD
RL = 100
SECOND
RL = 100
–60
THIRD
RL = 1k
–80
SECOND
RL = 1k
500mV
10ns
–100
1
FREQUENCY MHz
TPC 9. 2 V Step Response; G = –1, VS = ± 2.5 V, RL = 100 Ω
REV. B
G = +2
VOUT = 2V p-p
RF = 750
10
20
TPC 12. Distortion vs. Frequency; VS = ± 5 V
–7–
AD8012
0.5
0.5
G = +2
VO = 0.3V p-p
RF = 750
RL = 100
VS = 5V
NORMALIZED GAIN dB
0.3
0.2
G = +2
VO = 0.3V p-p
RF = 750
RL = 100
VS = +5V
0.4
0.3
NORMALIZED GAIN dB
0.4
0.1
0
–0.1
–0.2
0.2
0.1
0
–0.1
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
–0.5
0.1
1
10
FREQUENCY MHz
100
0.1
TPC 13. Gain Flatness; VS = ± 5 V
100
TPC 16. Gain Flatness; VS = +5 V
–40
5
G = +2
VOUT = 2V p-p
RF = 750
VO = 0.3V p-p
RF = 750
RL = 100
VS = 5V
4
3
NORMALIZED GAIN dB
–50
SECOND
DISTORTION – dBc
1
10
FREQUENCY MHz
–60
–70
THIRD
–80
2
1
0
–1
G = +10
–2
G = +1
G = +2
–3
–4
–90
10
100
RL – –5
1k
1
10
FREQUENCY MHz
500
TPC 17. Frequency Response; VS = ± 5 V
TPC 14. Distortion vs. Load Resistance; VS = +5 V,
Frequency = 500 kHz
9
–40
THIRD
RL = 100
G = +2
RF = 750
RL = 100
VS = 5V
6
OUTPUT VOLTAGE dBV
3
DISTORTION – dBc
100
–60
SECOND
RL = 1k
SECOND
RL = 100
–80
THIRD
RL = 1k
G = +2
VOUT = 2V p-p
RF = 750
1V RMS
0
–3
–6
–9
–12
–15
–18
–21
–100
1
10
1
20
FREQUENCY – MHz
10
FREQUENCY MHz
100
500
TPC 18. Output Voltage vs. Frequency; VS = ± 5 V,
G = +2, RL = 100 Ω
TPC 15. Distortion vs. Frequency; VS = +5 V
–8–
REV. B
AD8012
0
0
VIN = 0.2V p-p
VS = 5V, +5V
–10
–20
–20
–30
–30
–40
–40
–50
–60
–PSRR
–50
–60
–70
–70
–80
–80
–90
–90
–100
0.03
0.1
–100
10
1
FREQUENCY – MHz
100
500
100k
TPC 19. CMRR vs. Frequency; VS = ± 5 V, +5 V
1M
10M
FREQUENCY – Hz
100M
500M
TPC 22. PSRR vs. Frequency; VS = ± 5 V, +5 V
5
1k
VO = 0.3V p-p
RF = 750
RL = 100
VS = +5V
3
2
1
0
–1
G = +1
G = +10
–2
G = +2
–3
G = +2
RF = 750
100
OUTPUT RESISTANCE 4
NORMALIZED GAIN dB
VS = +5V OR 5V
G = +2
RF = 750
+PSRR
PSRR – dB
CMRR dB
–10
10
VS = +5V
VS = 5V
1
0.1
–4
–5
10
FREQUENCY – MHz
100
0.01
0.03
500
TPC 20. Frequency Response; VS = +5 V
G = +2
RF = 750
RL = 100
VS = +5V
0
100
500
135
0
115
–40
95
–6
–9
TZ dB OUTPUT VOLTAGE dBV
–3
10
1
FREQUENCY – MHz
TPC 23. Output Resistance vs. Frequency
3
1VRMS
0.1
–12
–15
–18
PHASE
–80
–120
75
55
–160
TZ(s)
35
–200
15
–240
–21
–24
–27
1
10
FREQUENCY MHz
100
–5
500
1k
TPC 21. Output Voltage vs. Frequency; VS = +5 V,
G = +2, RL = 100 Ω
REV. B
10k
100k
1M
10M
FREQUENCY Hz
100M
–280
1G
TPC 24. Open-Loop Transimpedance and
Phase vs. Frequency
–9–
PHASE – Degrees
1
AD8012
9
7
SWING – V p-p
G = +2
RF = 750
RL = 100
2V STEP
OUTPUT VOLTAGE ERROR – 0.1%/DIV
5V
8
6
5
+5V
4
3
2
1
0.1%
0
10
100
LOAD – 1k
10k
t=0
TPC 28. Settling Time, VS = ± 5 V
30
5
3.8
28
4
3.6
26
3.4
24
22
3.0
20
2.8
18
CURRENT NOISE
+IN/–IN
16
14
2.4
2.2
VOLTAGE NOISE
2.0
100
1k
10k
FREQUENCY – Hz
2
1
0
G = +1
–1
G = +10
–2
G = +2
–3
12
–4
10
100k
–5
1
10
FREQUENCY – MHz
100
500
TPC 29. Frequency Response; VS = ± 5 V
TPC 26. Noise vs. Frequency
9
0.5
RL = 1k
f = 5MHz
G = 2
R F = 750
0.3
NORMALIZED GAIN – dB
7
VO = 0.3V p-p
G = +2
RF = 750
RL = 1k
0.4
8
6
RL = 100
5
4
3
2
0.2
0.1
0
–0.1
–0.2
–0.3
1
0
VO = 0.3V p-p
RF = 750
RL = 1k
3
NORMALIZED GAIN dB
3.2
INPUT CURRENT NOISE – pA/ Hz
4.0
PEAK-TO-PEAK OUTPUT AT 5MHz (ⱕ1% THD) V
INPUT VOLTAGE NOISE – nV/ Hz
TPC 25. Output Swing vs. Load
2.6
5ns
–0.4
3
4
5
6
7
8
9
TOTAL SUPPLY VOLTAGE V
10
–0.5
11
0.1
1
10
FREQUENCY – MHz
100
TPC 30. Gain Flatness; VS = ± 5 V
TPC 27. Output Swing vs. Supply
–10–
REV. B
AD8012
0.5
–20
DRIVER
VO = 2V p-p
RL = 100
–40
0.3
–50
–60
SIDE 1
–70
–80
SIDE 2
–90
0.2
0.1
0
–0.1
–0.2
–100
–0.3
–110
–0.4
–120
0.03
VO = 0.3V p-p
RF = 750
RL = 1k
0.4
NORMALIZED GAIN – dB
INPUT REFERRED ERROR – dB
–30
–0.5
0.1
10
1
FREQUENCY – MHz
100
0.1
500
1
10
FREQUENCY – MHz
100
TPC 33. Gain Flatness; VS = +5 V
TPC 31. Crosstalk vs. Frequency
5
VO = 0.3V p-p
RF = 750
RL = 1k
4
NORMALIZED GAIN dB
3
+3V
VOUT
0V
2
VIN
1
0V
0
0V
G = +1
VIN
–1
0V
G = +10
–2
VOUT
G = +2
–3
–3V
–4
VOUT, 2V/DIV
20ns
–5
1
10
FREQUENCY – MHz
100
500
TPC 34. Overdrive Recovery; VS = ± 5 V, G = +2,
RF = 750 Ω, RL = 100 Ω, VIN = 3 V p-p (T = 1 µ s)
TPC 32. Frequency Response; VS = +5 V
REV. B
–11–
AD8012
THEORY OF OPERATION
The AD8012 is a dual, high speed CF amplifier that attains new
levels of bandwidth (BW), power, distortion, and signal swing
capability. Its wide dynamic performance (including noise) is
the result of both a new complementary high speed bipolar
process and a new and unique architectural design. The AD8012
uses a two-gain stage complementary design approach versus
the traditional single-stage complementary mirror structure
sometimes referred to as the Nelson amplifier. Though twin
stages have been tried before, they typically consumed high
power since they were of a folded cascade design, similar to that
of the AD9617. This design allows for the standing or quiescent
current to add to the high signal or slew current-induced stages.
In the time domain, the large signal output rise/fall time and
slew rate is typically controlled by the small signal BW of the
amplifier and the input signal step amplitude, respectively, and
not the dc quiescent current of the gain stages (with the exception of input level shift diodes Q1/Q2). Using two stages versus
one also allows for a higher overall gain bandwidth product
(GBWP) for the same power, resulting in lower signal distortion
and the ability to drive heavier external loads. In addition, the
second-gain stage also isolates (divides down) A3’s input
reflected load drive and the nonlinearities created, resulting in
relatively lower distortion and higher open-loop gain.
Overall, when high external load drive and low ac distortion is a
requirement, a twin-gain stage integrating amplifier like the
AD8012 will provide excellent results for lower power over the
A1
IPN
IPP
traditional single stage complementary devices. In addition,
because the AD8012 is a CF amplifier, closed-loop BW variations
versus external gain variations (varying RN) will be much lower
compared to a VF op amp, where the BW varies inversely with
gain. Another key attribute of this amplifier is its ability to run on
a single 5 V supply partially because of its wide common-mode
input and output voltage range capability. For 5 V supply
operation, the device consumes half the quiescent power (vs.
10 V supply) with little degradation in its ac and dc performance characteristics. See data sheet comparisons.
DC GAIN CHARACTERISTICS
Gain stages A1/A1B and A2/A2B combined provide negative
feedforward transresistance gain as shown in Figure 4. Stage A3
is a unity-gain buffer that provides external load isolation to A2.
Each stage uses a symmetrical complementary design (A3 is also
complementary though not explicitly shown). This is done to
reduce both second-order signal distortion and overall quiescent
power as previously described. In the quasi dc to low frequency
region, the closed-loop gain relationship can be approximated as:
noninverting operation
G = –RF /RN
inverting operation
These basic relationships are common to all traditional operational amplifiers.
CD
Z1 = R1 || C1
Z1
–VI
IQ1
G = 1+ RF /RN
A2
C P1
C P2
Q3
ICQ + IO
IR + IFC
Q1
VN
Ð
VP
+
VOI
ZI
A3
Z2
Q2
RF
IE
IR – IFC
Q4
VO
RL
CL
RN
ICQ – IO
Z1
IQ1
–VI
INP
IPN
A2
C P1
AD8012
A1
CD
Figure 4. Simplified Block Diagram
–12–
REV. B
AD8012
APPLICATIONS
Line Driving for HDSL
TO
RECEIVER
CIRCUITRY
High bitrate digital subscriber line (HDSL) is becoming
popular as a means of providing full duplex data communication at
rates up to 1.544 MBPS or 2.048 MBPS over moderate distances
via conventional telephone twisted pair wires. Traditional T1
(E1 in Europe) requires repeaters every 3,000 feet to 6,000 feet
to boost the signal strength and allow transmission over distances
of up to 12,000 feet. In order to achieve repeaterless transmission
over this distance, an HDSL modem requires a transmitted
power level of 13.5 dBm (assuming a line impedance of 135 Ω).
+3
0.88V
–1
–0.88V
–3
–2.64V
+1
11
–3
00
–3
00
+1
11
+3
10
–3
00
–1
01
–1
01
+1
11
–1
01
RG
1.5k
66.5
RF 12V p-p
750
6V p-p
135
66.5
0.1F
1:1
1:1
–5V
GAIN = +2
The immediate effect of back-termination is that the signal from
the amplifier is halved before being applied to the line. This
doubles the power the amplifier must deliver. However, the
back-termination resistors also play an important second role.
Full-duplex data transmission systems like HDSL simultaneously transmit data in both directions. As a result, the signal
on the line and across the back termination resistors is the
composite of the transmitted and received signal. The termination resistors are used to tap off this signal and feed it to the
receive circuitry. Because the receive circuitry “knows” what is
being transmitted, the transmitted data can be subtracted from
the digitized composite signal to reveal the received data.
Driving a line with a differential signal offers a number of
advantages compared to a single-ended drive. Because the two
outputs are always 180 degrees out of phase relative to one
another, the differential signal output is double the output
amplitude of either of the op amps. As a result, the differential
amplifier can have a peak-to-peak swing of 16 V (each op amp
can swing to ± 4 V), even though the power supply is ± 5 V.
–3
00
Figure 5. Time Domain Representation of an HDSL Signal
Many of the elements of a classic differential line driver are
shown in the HDSL line driver in Figure 6. A 6 V peak-to-peak
differential signal is applied to the input. The differential gain of
the amplifier (1+2 RF/RG) is set to +2, so the resulting differential output signal is 12 V p-p.
As is normal in telephony applications, a transformer galvanically isolates the differential amplifier from the line. In this case,
a 1:1 turns ratio is used. In order to correctly terminate the line,
it is necessary to set the output impedance of the amplifier to be
equal to the impedance of the line being driven (135 Ω in this
case). Because the transformer has a turns ratio of 1:1, the
impedance reflected from the line is equal to the line impedance
of 135 Ω (RREFL = RLINE/Turns Ratio2). As a result, two 66.5 Ω
resistors correctly terminate the line.
REV. B
6V p-p
UP TO
12,000 FEET
Figure 6. Differential for HDSL Applications
DAC
OUTPUT
+3
10
RF
750
TO
RECEIVER
CIRCUITRY
FILTERED
OUTPUT
TO LINE
DRIVER
–1
01
0.1F
1/2
AD8012
2.64V
+1
+
–
HDSL uses the two binary/one quaternary line code (2B1Q).
A sample 2B1Q waveform is shown in Figure 5. The digital bit
stream is broken up into groups of two bits. Four analog voltages (called quaternary symbols) are used to represent the four
possible combinations of two bits. These symbols are assigned
the arbitrary names +3, +1, –1, and –3. The corresponding
voltage levels are produced by a DAC that is usually part of an
analog front end circuit (AFEC). Before being applied to the
line, the DAC output is low-pass filtered and acquires the sinusoidal form shown in Figure 5. Finally, the filtered signal is
applied to the line driver. The line voltages that correspond to
the quaternary symbols +3, +1, –1, and –3 are 2.64 V, 0.88 V,
–0.88 V, and –2.64 V. This gives a peak-to-peak line voltage of
5.28 V.
SYMBOL
NAME VOLTAGE
+5V
1/2
AD8012
In addition, even-order harmonics (second, fourth, sixth, and
so on.) of the two single-ended outputs tend to cancel out one
another, so the total harmonic distortion (quadratic sum of all
harmonics) decreases compared to the single-ended case, even
as the signal amplitude is doubled. This is particularly advantageous in the case of the second harmonic. Because it is very
close to the fundamental, filtering becomes difficult. In this
application, the THD is dominated by the third harmonic,
which is 65 dB below the carrier (i.e., spurious-free dynamic
range = –65 dBc).
Differential line driving also helps to preserve the integrity of the
transmitted signal in the presence of electromagnetic interference (EMI). EMI tends to induce itself equally onto both the
positive and negative signal lines. As a result, a receiver with
good common-mode rejection will amplify the original signal
while rejecting induced (common-mode) EMI.
–13–
AD8012
Choosing the Appropriate Turns Ratio for the Transformer
Increasing the peak-to-peak output signal of the amplifier in the
previous example and adding a variation in the turns ratio of the
transformer can yield further enhancements to the circuit. The
output signal swing of the AD8012 can be increased to about
± 3.9 V before clipping occurs. This increases the peak-to-peak
output of the differential amplifier to 15.6 V. Because the signal
applied to the primary winding is now bigger, the transformer
turns ratio of 1:1 can be replaced with a (step-down) turns ratio
of about 1.3:1 (from amplifier to line). This steps the 7.8 V
peak-to-peak primary voltage down to 6 V. This is the same
secondary voltage of the earlier examples, so the resulting power
delivered to the line is the same.
The received signal, which is small relative to the transmitted
signal, will, however, be stepped up by a factor of 1.3. Amplifying
the received signal in this manner enhances its signal-to-noise
ratio and is useful when the received signal is small compared to
the to-be-transmitted signal.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance ground path. The ground plane should be removed
from the area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply bypassing (see Figure 7).
One end should be connected to the ground plane and the other
within 1/8 inch of each power pin. An additional (4.7 µF to 10 µF)
tantalum electrolytic capacitor should be connected in parallel.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to
a minimum. Capacitance greater than 1.5 pF at the inverting
input will significantly affect high speed performance when
operating at low noninverting gains.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). They should be designed with the
proper system characteristic impedance and be properly terminated at each end.
The impedance reflected from the 135 Ω line now becomes
228 Ω (1.32 ⫻ 135 Ω). With a correctly terminated line, the
amplifier must now drive a total load of 456 Ω (114 Ω + 114 Ω
+ 228 Ω), considerably more than the original 270 Ω load. This
reduces the drive current from the op amps by about 40%.
INVERTING CONFIGURATION
RF
RG
RO*
VIN
VOUT
+VS
RT
10F
+
0.1F
More significant, however, is the reduction in dynamic power
consumption—that is, the power the amplifier must consume in
order to deliver the load power. Increasing the output signal so
that it is as close as possible to the power rails minimizes the
power consumed in the amplifier.
There is, however, a price to pay in terms of increased signal
distortion. Increasing the output signal of each op amp from the
original ± 3 V to ± 3.9 V reduces the spurious-free dynamic
range (SFDR) from –65 dB to –50 dB (measured at 500 kHz),
even though the overall load impedance has increased from
270 Ω to 456 Ω.
*RO CHOSEN FOR CHARACTERISTIC IMPEDANCE.
RG
NONINVERTING CONFIGURATION
RF
RO*
VOUT
LAYOUT CONSIDERATIONS
VIN
The specified high speed performance of the AD8012 requires
careful attention to board layout and component selection.
Table I shows recommended component values for the AD8012
and Figures 8–13 show recommended layouts for the 8-lead
SOIC and MSOP packages for a positive gain. Proper RF
design techniques and low parasitic component selections
are mandatory.
0.1F
RT
10F
+
–VS
*RO CHOSEN FOR CHARACTERISTIC IMPEDANCE.
Figure 7. Inverting and Noninverting Configurations
Table I. Typical Bandwidth vs. Gain Setting Resistors
Gain
RF
RG
RT
Small Signal –3 dB BW (MHz),
VS = 5 V, RL = 1 k
–1
+1
+2
+10
750 Ω
750 Ω
750 Ω
750 Ω
750 Ω
53.6 Ω
49.9 Ω
49.9 Ω
49.9 Ω
110
350
150
40
750 Ω
82.5 Ω
RT chosen for 50 Ω characteristic input impedance.
–14–
REV. B
AD8012
Figure 8. Universal SOIC Noninverter Top Silkscreen
Figure 11. Universal MSOP Noninverter Top
Silkscreen
Figure 9. Universal SOIC Noninverter Top
Figure 12. Universal MSOP Noninverter Top
Figure 10. Universal SOIC Noninverter Bottom
Figure 13. Universal MSOP Noninverter Bottom
REV. B
–15–
AD8012
OUTLINE DIMENSIONS
8-Lead Standard Small Outline Package [SOIC]
Narrow Body
(R-8)
C01049–0–12/03(B)
Dimensions shown in millimeters and (inches)
5.00 (0.1968)
4.80 (0.1890)
4.00 (0.1574)
3.80 (0.1497)
8
5
1
4
6.20 (0.2440)
5.80 (0.2284)
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
SEATING
0.10
PLANE
0.50 (0.0196)
45
0.25 (0.0099)
1.75 (0.0688)
1.35 (0.0532)
8
0.25 (0.0098) 0 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
3.00
BSC
8
5
4.90
BSC
3.00
BSC
1
4
PIN 1
0.65 BSC
1.10 MAX
0.15
0.00
0.38
0.22
COPLANARITY
0.10
0.23
0.08
8
0
0.80
0.60
0.40
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187AA
Revision History
Location
Page
12/03—Data Sheet changed from REV. A to REV. B.
Renumbered figures and TPCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal
Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
–16–
REV. B
Similar pages