TI1 CDCV855 2.5-v phase-lock loop clock driver Datasheet

CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
D Phase-Lock Loop Clock Driver for Double
D
D
D
D
D
D
D
D
D
PW PACKAGE
(TOP VIEW)
Data-Rate Synchronous DRAM
Applications
Spread Spectrum Clock Compatible
Operating Frequency: 60 MHz to 180 MHz
Low Jitter (cyc–cyc): ±50 ps
Distributes One Differential Clock Input to
Four Differential Clock Outputs
Enters Low Power Mode and Three-State
Outputs When Input CLK Signal Is Less
Than 20 MHz or PWRDWN Is Low
Operates From Dual 2.5-V Supplies
28-Pin TSSOP Package
Consumes < 200-µA Quiescent Current
External Feedback PIN (FBIN, FBIN) Are
Used to Synchronize the Outputs to the
Input Clocks
GND
Y0
Y0
VDDQ
GND
CLK
CLK
VDDQ
AVDD
AGND
VDDQ
Y1
Y1
GND
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
10
19
11
18
12
17
13
16
14
15
GND
Y3
Y3
VDDQ
PWRDWN
FBIN
FBIN
VDDQ
FBOUT
FBOUT
VDDQ
Y2
Y2
GND
description
The CDCV855 is a high-performance, low-skew, low-jitter zero delay buffer that distributes a differential clock
input pair (CLK, CLK) to four differential pairs of clock outputs (Y[0:3], Y[0:3]) and one differential pair of
feedback clock outputs (FBOUT, FBOUT). When PWRDWN is high, the outputs switch in phase and frequency
with CLK. When PWRDWN is low, all outputs are disabled to a high-impedance state (3-state), and the PLL is
shut down (low-power mode). The device also enters this low-power mode when the input frequency falls below
a suggested detection frequency that is below 20 MHz (typical 10 MHz). An input frequency detection circuit
detects the low-frequency condition and after applying a >20-MHz input signal this detection circuit turns on the
PLL again and enables the outputs.
When AVDD is tied to GND, the PLL is turned off and bypassed for test purposes. The CDCV855 is also able
to track spread spectrum clocking for reduced EMI.
Since the CDCV855 is based on PLL circuitry, it requires a stabilization time to achieve phase-lock of the PLL.
This stabilization time is required following power up. The CDCV855 is characterized for both commercial and
industrial temperature ranges.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
TSSOP (PW)
0°C to 70°C
CDCV855PW
– 40°C to 85°C
CDCV855IPW
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
FUNCTION TABLE
(Select Functions)
INPUTS
OUTPUTS
PLL
AVDD
GND
PWRDWN
CLK
CLK
Y[0:3]
Y[0:3]
FBOUT
FBOUT
H
L
H
L
H
L
H
Bypassed/Off
GND
H
H
L
H
L
H
L
Bypassed/Off
X
L
L
H
Z
Z
Z
Z
Off
X
L
H
L
Z
Z
Z
Z
Off
2.5 V (nom)
H
L
H
L
H
L
H
On
2.5 V (nom)
H
H
L
H
L
H
L
On
2.5 V (nom)
X
<20 MHz{
<20 MHz{
Z
Z
Z
Z
Off
† Typically 10 MHz
functional block diagram
3
2
PWRDWN
12
24
Powerdown
and Test
Logic
9
AVDD
13
17
16
26
27
FBIN
PLL
23
22
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
AGND
10
Ground for 2.5-V analog supply
AVDD
CLK, CLK
9
2.5-V analog supply
FBIN, FBIN
FBOUT, FBOUT
GND
PWRDWN
6, 7
I
Differential clock input
23, 22
I
Feedback differential clock input
19, 20
O
Feedback differential clock output
1, 5, 14, 15, 28
24
Ground
I
Control input to turn device in the power-down mode
VDDQ
Y[0:3]
4, 8, 11, 18, 21, 25
3, 12, 17, 26
O
Buffered output copies of input clock, CLK
Y[0:3]
2, 13, 16, 27
O
Buffered output copies of input clock, CLK
2
Y1
Y1
Y2
Y2
Y3
Y3
FBOUT
20 FBOUT
7
CLK
FBIN
19
6
CLK
Y0
Y0
2.5-V supply
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage range, VDDQ, AVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V
Input voltage range, VI (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VDDQ + 0.5 V
Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VDDQ + 0.5 V
Input clamp current, IIK (VI < 0 or VI > VDDQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Output clamp current, IOK (VO < 0 or VO > VDDQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous output current, IO (VO = 0 to VDDQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current to GND or VDDQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 3): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105.8°C/W
Storage temperature range Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. This value is limited to 3.6 V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions (see Note 4)
MIN
Supply voltage, VDDQ, AVDD
TYP
PWRDWN
CLK, CLK, FBIN, FBIN
High level input voltage,
High-level
voltage VIH
PWRDWN
DC input signal voltage (see Note 5)
2.7
V
–0.3
VDDQ/2 – 0.18
0.7
V
VDDQ/2 + 0.18
1.7
CLK, FBIN
Output differential cross-voltage, VO(X) (see Note 7)
0.36
VDDQ/2 – 0.2
VDDQ/2 – 0.2
Input differential pair cross-voltage, VI(X) (see Note 7)
Commercial
Industrial
V
V
V
mA
12
mA
1
4
V/ns
0
85
–40
85
Low-level output current, IOL
Input slew rate, SR (see Figure 7)
VDDQ/2
VDDQ + 0.6
VDDQ/2 + 0.2
V
VDDQ/2 + 0.2
–12
High-level output current, IOH
Operating free
free-air
air temperature
temperature, TA
VDDQ + 0.3
VDDQ
–0.3
Differential input signal voltage, VID (see Note 6)
UNIT
2.3
CLK, CLK, FBIN, FBIN
Low level input voltage,
Low-level
voltage VIL
MAX
V
°C
NOTES: 4. Unused inputs must be held high or low to prevent them from floating.
5. DC input signal voltage specifies the allowable dc execution of differential input.
6. Differential input signal voltage specifies the differential voltage |VTR – VCP| required for switching, where VTR is the true input level
and VCP is the complementary input level.
7. Differential cross-point voltage is expected to track variations of VDDQ and is the voltage at which the differential signals must be
crossing.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MAX
UNIT
–1.2
V
Input voltage
VOH
High level output voltage
High-level
VOL
Low level output voltage
Low-level
IOH
IOL
VOD
Output voltage swing
VOX
Output differential
cross-voltage}
II
Input current
VDDQ = 2.7 V,
VI = 0 V to 2.7 V
±10
µA
IOZ
High-impedance-state output
current
VDDQ = 2.7 V,
VO = VDDQ or GND
±10
µA
IDD(PD)
Power-down current on
VDDQ + AVDD
CLK and CLK = 0 MHz; PWRDWN = Low;
Σ of IDD and AIDD
100
200
µA
Differential outputs
are terminated with
120 Ω / CL = 14 pF
150
180
AIDD
CI
VDDQ = 2.3 V,
II = –18 mA
VDDQ = min to max, IOH = –1 mA
TYP†
VIK
IDD
All inputs
MIN
High-level output current
VDDQ = 2.3 V,
VDDQ = 2.3 V,
IOL = 12 mA
VO = 1 V
Low-level output current
VDDQ = 2.3 V,
VO = 1.2 V
Dynamic current on VDDQ
Supply current on AVDD
VDDQ – 0.1
1.7
VDDQ = 2.3 V,
IOH = –12 mA
VDDQ = min to max, IOL = 1 mA
V
0.1
–18
–32
mA
26
35
mA
1.1
Differential outputs are terminated with
120 Ω
Differential outputs
are terminated with
120 Ω / CL = 0 pF
V
0.6
VDDQ/2 – 0.2
VDDQ – 0.4
VDDQ/2
V
VDDQ/2 + 0.2
fO = 167 MHz
fO = 167 MHz
VDDQ = 2.5 V
mA
130
160
8
10
mA
Input capacitance
VI = VDDQ or GND
2
2.5
3
pF
CO
Output capacitance
VDDQ = 2.5 V
VO = VDDQ or GND
2.5
3
3.5
pF
† All typical values are at respective nominal VDDQ.
‡ Differential cross-point voltage is expected to track variation of VDDQ and is the voltage at which the differential signals must be crossing.
timing requirements over recommended ranges of supply voltage and operating free-air
temperature
PARAMETER
fCLK
Operating clock frequency
Input clock duty cycle
MIN
MAX
UNIT
60
180
MHz
40%
60%
Stabilization time (PLL mode)W
10
µs
Stabilization time (Bypass mode)w
30
ns
§ Recovery time required when the device goes from power-down mode into bypass mode (test mode with AVDD at GND).
¶ Time required for the integrated PLL circuit to obtain phase lock of its feedback signal to its reference signal. For phase lock to be obtained, a
fixed-frequency, fixed-phase reference signal must be present at CLK. Until phase lock is obtained, the specifications for propagation delay, skew,
and jitter parameters given in the switching characteristics table are not applicable. This parameter does not apply for input modulation under
SSC application.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
switching characteristics
PARAMETER
tPLH}
tPHL}
tjit(per)
( )§
Test mode/CLK to any output
High-to-low level propagation delay time
Test mode/CLK to any output
Jitter (period),
(period) See Figure 5
tjit(cc)
( )§
Jitter (cycle-to-cycle),
(cycle to cycle) See Figure 2
tjit(hper)
jit(h er)§
Half-period
Half
eriod jitter, See Figure 6
tslr(o)
TEST CONDITIONS
Low-to-high level propagation delay time
Output clock slew rate,
rate See Figure 7
tsk(o)¶
Output skew, See Figure 4
ns
4.5
ns
ps
ps
100/133/167/180 MHz
–35
35
66 MHz
–60
60
100/133/167/180 MHz
–50
50
66 MHz
–130
130
100 MHz
–90
90
133/167/180 MHz
–75
75
Load = 120Ω / 14 pF
1
2
V/ns
Load = 120Ω / 4 pF
1
3
V/ns
66 MHz
–180
180
100/133 MHz
–130
130
167/180 MHz
–90
90
66 MHz
–230
230
100/133 MHz
–170
170
167/180 MHz
–100
100
66 MHz
–150
150
100/133/167/180 MHz
–100
100
tr, tf
Output rise and fall times (20% – 80%)
Load: 120 Ω/14 pF
† All typical values are at a respective nominal VDDQ.
‡ Refers to transition of noninverting output
§ This parameter is assured by design but can not be 100% production tested.
¶ All differential output pins are terminated with 120 Ω/14 pF.
POST OFFICE BOX 655303
UNIT
55
SSC on
Static phase offset,
offset See Figure 3(a)
MAX
4.5
–55
Dynamic phase
hase offset (this includes jitter),
See Figure 3(b)
t(Ø)
TYP†
66 MHz
SSC off
td(Ø)w
MIN
• DALLAS, TEXAS 75265
650
ps
ps
s
ps
ps
50
ps
900
ps
5
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
PARAMETER MEASUREMENT INFORMATION
VDD/2
CDCV855
SCOPE
C = 14 pF
–VDD/2
Z = 50 Ω
R = 10 Ω
Z = 60 Ω
R = 50 Ω
V(TT)
Z = 60 Ω
R = 10 Ω
Z = 50 Ω
C = 14 pF
R = 50 Ω
–VDD/2
V(TT)
–VDD/2
NOTE: V(TT) = GND
Figure 1. Output Load Test Circuit
Yx, FBOUT
Yx, FBOUT
tc(n)
tc(n+1)
tjit(cc) = tc(n) – tc(n+1)
Figure 2. Cycle-to-Cycle Jitter
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
PARAMETER MEASUREMENT INFORMATION
CLK
CLK
FBIN
FBIN
t(φ) n
∑1
t(φ) n+1
n=N
t(φ) n
t(φ) =
N
(N is a Large Number of Samples)
(a) Static Phase Offset
CLK
CLK
FBIN
FBIN
t(φ)
td(φ)
t(φ)
td(φ)
td(φ)
td(φ)
(b) Dynamic Phase Offset
Figure 3. Phase Offset
Yx
Yx
Yx, FBOUT
Yx, FBOUT
tsk(o)
Figure 4. Output Skew
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
CDCV855, CDCV855I
2.5-V PHASE-LOCK LOOP CLOCK DRIVER
SCAS660A – SEPTEMBER 2001 – REVISED DECEMBER 2002
PARAMETER MEASUREMENT INFORMATION
Yx, FBOUT
Yx, FBOUT
tc(n)
Yx, FBOUT
Yx, FBOUT
1
fo
tjit(per) = tc(n) –
1
fo
Figure 5. Period Jitter
Yx, FBOUT
Yx, FBOUT
t(hper_n+1)
t(hper_n)
1
fo
1
tjit(hper) = t(hper_n) –
2xfo
Figure 6. Half-Period Jitter
80%
80%
VID, VOD
Clock Inputs
and Outputs
20%
20%
tslrr(i), tslrr(o)
tslrf(i), tslrf(o)
Figure 7. Input and Output Slew Rates
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
CDCV855IPW
NRND
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
CDCV855-I
CDCV855IPWG4
NRND
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
CDCV855-I
CDCV855IPWR
NRND
TSSOP
PW
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
CDCV855-I
CDCV855IPWRG4
NRND
TSSOP
PW
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
CDCV855-I
CDCV855PW
NRND
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
CDCV855
CDCV855PWG4
NRND
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
CDCV855
CDCV855PWR
NRND
TSSOP
PW
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
CDCV855
CDCV855PWRG4
NRND
TSSOP
PW
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
CDCV855
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Feb-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
CDCV855IPWR
TSSOP
PW
28
2000
330.0
16.4
6.9
10.2
1.8
12.0
16.0
Q1
CDCV855PWR
TSSOP
PW
28
2000
330.0
16.4
6.9
10.2
1.8
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Feb-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CDCV855IPWR
TSSOP
PW
28
2000
367.0
367.0
38.0
CDCV855PWR
TSSOP
PW
28
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Similar pages