Panasonic ERJ8GEYJ102Y Thick film chip resistor Datasheet

Thick Film Chip Resistors
Thick Film Chip Resistors
01005, 0201, 0402, 0603, 0805,
1206, 1210, 1812, 2010, 2512
Type:
ERJ XG, 1G, 2G, 3G, 6G, 8G,
14, 12, 12Z, 1T
■ Features
● Small size and lightweight
● High reliability
Metal glaze thick film resistive element and three layers of electrodes
● Compatible with placement machines
Taping packaging available
● Suitable for both reflow and flow soldering
● Reference Standards
IEC 60115-8, JIS C 5201-8, EIAJ RC-2134B
■ Explanation of Part Numbers
● ERJXGN, 1GE, 2GE, 3GE, 6GE, 8GE, 14, 12, 12Z, 1T Series, ±5 % type
1
2
3
4
5
6
7
8
9
10
11
12
E
R
J
3
G
E
Y
J
1
0
2
V
Product Code
Thick Film
Chip Resistors
Size, Power Rating
Type : inches Power R.
XGN : 01005 0.031 W
0.05 W
1GE : 0201
0.1 W
2GE : 0402
0.1 W
3GE : 0603
0.125 W
6GE : 0805
0.25 W
8GE : 1206
0.5 W
14 : 1210
0.75 W
12 : 1812
0.75 W
12Z : 2010
1W
1T : 2512
Code
Resistance Tolerance
Marking
Marking
Code
J
0
Tolerance
±5 %
Jumper
Code
Packaging Methods
Packaging
Type
Y
Pressed Carrier Taping
2 mm pitch, 20000 pcs.
ERJXGN
C
Pressed Carrier Taping
2 mm pitch, 15000 pcs.
ERJ1GE
Resistance Value
X
Punched Carrier Taping
2 mm pitch, 10000 pcs.
ERJ2GE
The first two digits are significant figures of resistance and
the third one denotes number of zeros following.
Decimal Point is expressed by R as 4.7 = 4R7.
Jumper is expressed by R00.
V
Punched Carrier Taping
4 mm pitch
Y
✽Nil
Value Marking on
black side
No marking
U
✽ When omitted, the rest of the P/N factors shall be moved up respectively.
(Only XGN, 1GN, 2GE type)
ERJ3GE
ERJ6GE
ERJ8GE
ERJ14
Embossed CarrierTaping ERJ12
4 mm pitch
ERJ12Z
ERJ1T
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Jul. 2008
Thick Film Chip Resistors
■ Dimensions in mm (not to scale)
■ Construction
L
a
W
Protective coating
t
Electrode (Inner)
Alumina substrate
b
Dimensions (mm)
Type
(inches)
ERJXG
(01005)
ERJ1G
(0201)
ERJ2G
(0402)
ERJ3G
(0603)
ERJ6G
(0805)
ERJ8G
(1206)
ERJ14
(1210)
ERJ12
(1812)
ERJ12Z
(2010)
ERJ1T
(2512)
Electrode
(Between)
Thick film
resistive element
Electrode (Outer)
L
W
a
b
Mass (Weight)
(g/1000 pcs.)
t
0.40 ±0.02 0.20 ±0.02 0.10 ±0.03 0.10 ±0.03 0.13 ±0.02
0.04
0.60 ±0.03 0.30 ±0.03 0.10 ±0.05 0.15 ±0.05 0.23 ±0.03
0.15
1.00 ±0.05 0.50 ±0.05 0.20 ±0.10 0.25 ±0.05 0.35 ±0.05
0.8
1.60
±0.15
2.00
±0.20
3.20
+0.05
–0.20
3.20
±0.20
4.50
±0.20
5.00
±0.20
6.40
±0.20
0.80
+0.15
–0.05
1.25
±0.10
1.60
+0.05
–0.15
2.50
±0.20
3.20
±0.20
2.50
±0.20
3.20
±0.20
0.30
±0.20
0.40
±0.20
0.50
±0.20
0.50
±0.20
0.50
±0.20
0.60
±0.20
0.65
±0.20
0.30
±0.15
0.40
±0.20
0.50
±0.20
0.50
±0.20
0.50
±0.20
0.60
±0.20
0.60
±0.20
0.45
±0.10
2
0.60
±0.10
4
0.60
±0.10
10
0.60
±0.10
16
0.60
±0.10
27
0.60
±0.10
27
0.60
±0.10
45
■ Ratings
<For Resistor>
Type
(inches)
Limiting Element Maximum Overload Resistance
Power Rating
(2)
Voltage (Maximum
Voltage
Tolerance
at 70 °C (W)
(1)
RCWV) (V)
(%)
(V)
Resistance
Range
()
T.C.R.
[10 –6 /°C
(ppm/°C)]
Category Temperature
Range (Operating
Temperature Range)
(°C)
ERJXG
(01005)
0.031
15
30
±5
<10 : –100 to +600
4.7 to 1 M (E24) 10 to 100 : ±300
100 < : ±200
–55 to +125
ERJ1G
25
50
±5
1 to 10 M (E24)
–55 to +125
–55 to +155
(0201)
0.05
ERJ2G
(0402)
0.1
50
100
±5
<10 :
1 to 10 M (E24) –100 to +600
ERJ3G
(0603)
0.1
75
150
±5
1 to 10 M (E24)
–55 to +155
ERJ6G
(0805)
0.125
150
200
±5
1 to 10 M (E24)
–55 to +155
ERJ8G
(1206)
0.25
200
400
±5
ERJ14
(1210)
0.5
200
400
ERJ12
0.75
200
500
(1812)
±5
10 to 1 M:
1 to 10 M (E24) ±200
1 to 10 M (E24)
–55 to +155
±5
1 to 10 M (E24)
–55 to +155
1 to 10 M (E24) 1 M<:
–400 to +150
1 to 1 M (E24)
–55 to +155
ERJ12Z
(2010)
0.75
200
500
±5
ERJ1T
1
200
500
±5
(2512)
–55 to +155
–55 to +155
(1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=Power Rating Resistance Values, or Limiting Element Voltage
(max. RCWV) listed above, whichever less.
(2) Overload (Short-time Overload) Test Voltage (SOTV) shall be determined from SOTV=2.5Power Rating or max. Overload Voltage listed above
whichever less.
Type
Rated Current Maximum Overload Current
(inches)
(A)
(A)
ERJXG (01005)
0.5
1
ERJ1G (0201)
ERJ2G (0402)
1
2
ERJ3G (0603)
ERJ6G (0805)
ERJ8G (1206)
ERJ14 (1210)
2
4
ERJ12 (1812)
ERJ12Z (2010)
ERJ1T (2512)
Power Derating Curve
For resistors operated in ambient temperatures above
70 °C, power rating shall be derated in accordance
with the figure below.
–55 °C
100
80
Rated Load (%)
<For Jumper>
70 °C
2G, 3G, 6G, 8G,
14, 12, 12Z, 1T
60
40
XG, 1G
155 °C
20
125 °C
0
–60 –40 –20 0 20 40 60 80 100 120 140 160 180
Ambient Temperature (°C)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Jul. 2008
Thick Film Chip Resistors
■ Packaging Methods (Taping)
● Standard Quantity
Type
Kind of Taping
ERJXG
ERJ1G
ERJ2G
ERJ3G
ERJ6G
ERJ8G
ERJ14
ERJ12
ERJ12Z
ERJ1T
Pressed Carrier Taping
Pitch (P1)
Quantity
2 mm
20000 pcs./reel
15000 pcs./reel
10000 pcs./reel
Punched Carrier Taping
5000 pcs./reel
4 mm
Embossed Carrier Taping
4000 pcs./reel
● Carrier Tape
(Unit : mm)
Pressed Carrier
Punched Carrier
Embossed Carrier
P1
P2
P0
B
W
F
E
φD0
T
T
T
A
P1 (2 mm pitch)
φD1 (Only Emboss)
Type
ERJXG
ERJ1G
ERJ2G
ERJ3G
ERJ6G
ERJ8G
ERJ14
ERJ12
ERJ12Z
ERJ1T
A
0.24±0.03
0.38 ±0.05
0.67±0.05
1.10 ±0.10
1.65±0.15
2.00 ±0.15
2.80 ±0.20
3.50 ±0.20
2.80 ±0.20
3.60 ±0.20
B
W
F
E
P1
P2
P0
φD0
0.45±0.03
0.68 ±0.05
2.00 ±0.10
±0.05
1.17
8.00 ±0.20
1.90 ±0.10
3.50 ±0.05
±0.20
2.50
1.75±0.10
2.00 ±0.05 4.00 ±0.10 1.50+0.10
−0
3.60 ±0.20
3.50 ±0.20 8.00 ±0.30
4.00 ±0.10
±0.20
4.80
5.30 ±0.20 12.00 ±0.30 5.50 ±0.20
6.90 ±0.20
T
0.31±0.05
0.42±0.05
0.52±0.05
0.70 ±0.05
0.84±0.05
1.00 ±0.10
● Taping Reel
φD1
–
–
–
–
–
–
1.0+0.10
−0
1.5 min.
(Unit : mm)
T
φB
φC
φA
W
Type
ERJXG
ERJ1G
ERJ2G
ERJ3G
ERJ6G
ERJ8G
ERJ14
ERJ12
ERJ12Z
ERJ1T
φA
φB
φC
W
T
9.0 ±1.0
11.4±1.0
13.0 ±1.0
15.4±2.0
13.0 ±1.0
180.0 +0
–3.0 60 min.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Feb. 2006
Thick Film Chip Resistors
■ Recommended Land Pattern
c
In case of flow soldering, the land width must be smaller than the Chip Resistor width to control the solder amount properly.
Generally, the land width should be 0.7 to 0.8 times (W) of the width of chip resistor. In case of reflow soldering, solder
amount can be adjusted, therefore the land width should be set to 1.0 to 1.3 times chip resistor width (W).
Dimensions (mm)
Type
(inches)
a
b
c
Chip Resistor
a
b
ERJXG (01005)
ERJ1G (0201)
ERJ2G (0402)
ERJ3G (0603)
ERJ6G (0805)
ERJ8G (1206)
ERJ14(1210)
ERJ12(1812)
ERJ12Z(2010)
ERJ1T(2512)
0.15 to 0.20
0.3 to 0.4
0.5 to 0.6
0.7 to 0.9
1 to 1.4
2 to 2.4
2 to 2.4
3.3 to 3.7
3.6 to 4
5 to 5.4
0.5 to 0.7
0.8 to 0.9
1.4 to 1.6
2 to 2.2
3.2 to 3.8
4.4 to 5
4.4 to 5
5.7 to 6.5
6.2 to 7
7.6 to 8.6
0.20 to 0.25
0.25 to 0.35
0.4 to 0.6
0.8 to 1
0.9 to 1.4
1.2 to 1.8
1.8 to 2.8
2.3 to 3.5
1.8 to 2.8
2.3 to 3.5
■ Recommended Soldering Conditions
Recommendations and precautions are described below.
● Recommended soldering conditions for reflow
· Reflow soldering shall be performed a maximum of
two times.
· Please contact us for additional information when
used in conditions other than those specified.
· Please measure the temperature of the terminals
and study every kind of solder and printed circuit
board for solderability before actual use.
Temperature
Peak
Preheating
Heating
For soldering (Example : Sn/Pb)
Preheating
Main heating
Peak
Temperature
140 °C to 160 °C
Above 200 °C
235 ± 5 °C
Time
60 s to 120 s
30 s to 40 s
max. 10 s
For lead-free soldering (Example : Sn/Ag/Cu)
Temperature
Time
Preheating
150 °C to 180 °C
60 s to 120 s
Main heating
Above 230 °C
30 s to 40 s
Peak
max. 260 °C
max. 10 s
Time
● Recommended soldering conditions for flow
Preheating
Soldering
For soldering
Temperature
Time
140 °C to 180 °C
60 s to 120 s
245 ± 5 °C
20 s to 30 s
For lead-free soldering
Temperature
Time
150 °C to 180 °C
60 s to 120 s
max. 260 °C
max. 10 s
Safety Precautions
The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors
shown on page ER2 of this catalog.
1. Take measures against mechanical stress during and after mounting of Thick Film Chip Resistors (hereafter called the
resistors) so as not to damage their electrodes and protective coatings.
2. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations
of the resistors when installed in your products before use.
Never exceed the rated power. Otherwise, the performance and/or reliability of the resistors may be impaired.
3. Do not use halogen-based or other high-activity flux. Otherwise, the residue may impair the resistors' performance
and/or reliability.
4. When soldering with a soldering iron, never touch the resistors' bodies with the tip of the soldering iron. When using a
soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 °C max.).
5. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing
problems such as cracks and faulty characteristics. Avoid applying an excessive amount of solder.
6. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, the resistors'
protective coatings and bodies may be chipped, affecting their performance.
7. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Feb. 2006
Safety Precautions
(Common precautions for Fixed Resistors)
• When using our products, no matter what sort of equipment they might be used for, be sure to make a written
agreement on the specifi cations with us in advance. The design and specifi cations in this catalog are subject
to change without prior notice.
• Do not use the products beyond the specifications described in this catalog.
• This catalog explains the quality and performance of the products as individual components. Before use, check
and evaluate their operations when installed in your products.
• Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment
where a defect in these products may cause the loss of human life or other significant damage, such as damage to
vehicles (au to mo bile, train, vessel), traffi c lights, medical equipment, aerospace equipment, elec tric heating
appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.
✽ Systems equipped with a protection circuit and a protection device
✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault
(1) Precautions for use
• These products are designed and manufactured for general and stan dard use in general elec tron ic
equipment (e.g. AV equipment, home electric ap plianc es, offi ce equipment, information and com mu ni cation
equipment)
• These products are not intended for use in the following special conditions. Before using the products, carefully
check the effects on their quality and performance, and determine whether or not they can be used.
1. In liquid, such as water, oil, chemicals, or organic solvent
2. In direct sunlight, outdoors, or in dust
3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
4. Electric Static Discharge (ESD) Environment
These components are sensitive to static electricity and can be damaged under static shock (ESD).
Please take measures to avoid any of these environments.
Smaller components are more sensitive to ESD environment.
5. Electromagnetic Environment
Avoid any environment where strong electromagnetic waves exist.
6. In an environment where these products cause dew condensation
7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin
or other materials
• These products generate Joule heat when energized. Carefully position these products so that their heat will not
affect the other components.
• Carefully position these products so that their temperatures will not exceed the category temperature range due
to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or
inflammables, such as vinyl-coated wires, near these products .
• Note that non- cleaning solder, halogen-based highly active fl ux, or water-soluble fl ux may deteriorate the
performance or reliability of the products.
• Carefully select a fl ux cleaning agent for use after soldering. An unsuitable agent may deteriorate the
performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave
water residues. Otherwise, the insulation performance may be deteriorated.
(2) Precautions for storage
The performance of these products, including the solderability, is guaranteed for a year from the date of arrival at your
company, provided that they remain packed as they were when delivered and stored at a temperature of 5 °C to 35 °
C and a relative humidity of 45 % to 85 %.
Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their
electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials)
may be deformed or deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
2. In direct sunlight
<Package markings>
Package markings include the product number, quantity, and country of origin.
In principle, the country of origin should be indicated in English.
Oct. 2007
– ER3 –
Similar pages