AOSMD AOZ8014 4-line emi filter with integrated esd protection Datasheet

AOZ8014
4-Line EMI Filter with Integrated ESD Protection
General Description
Features
The AOZ8014 is an 4-line device integrating EMI filtering
with ESD protection for each line. It is designed to
suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic
equipment. This state-of-the-art device utilizes AOS
leading edge Trench Vertical Structure [TVS]2 ™
technology for superior clamping performance and filter
attenuation over the full operating display range. The
AOZ8014 has been optimized for protection of color LCD
displays and CCD camera lines in cellular phones and
other portable consumer electronic devices.
●
●
●
●
●
The AOZ8014 consists of four identical circuits
comprised of TVS diodes for ESD protection, and a
resistor–capacitor network for EMI/RFI filtering.
A series resistor value of 100Ω and a capacitance
value of 17pF are used to achieve -25dB minimum
attenuation from 800MHz to 3.0GHz. The TVS diodes
provide effective suppression of ESD voltages in excess
of ±17kV (air discharge) and ±17kV (contact discharge).
This exceeds IEC 61000-4-2, level 4 ESD immunity test.
4 lines for EMI filtering and ESD protection:
– Exceeds IEC 61000-4-2, level 4 (ESD) immunity test
– ±17kV (air discharge) and ±17kV (contact discharge)
Trench Vertical Structure [TVS]2 ™ based technology
used to achieve excellent ESD clamping & filter
performance over the full operating display range
Filter performance: -25db attenuation from 800MHz to
3.0GHz
Low operating voltage: 5.0V
Capacitance stability over wide range of voltages and
temperatures
●
DFN package, 2.0 x 2.0 mm
●
Pb-Free device
Applications
●
●
●
The AOZ8014 comes in an RoHS compliant, 2.0mm x
2.0mm DFN package and is rated over a -40°C to +85°C
ambient temperature range.
EMI filtering and ESD protection for data lines
LCD displays, camera interface, I/O interface
Portable handheld devices, cell phones,
PDA phones
RoHS
Compliant
Electrical Schematic (each channel)
100Ω
CHn
(n = 1–4)
17pF
17pF
GND
Figure 1.
Rev. 1.3 November 2008
www.aosmd.com
Page 1 of 6
AOZ8014
Ordering Information
Part Number
Ambient Temperature Range
Package
Environmental
AOZ8014DI
-40°C to +85°C
DFN-8
RoHS Compliant
All AOS products are offered in packages with Pb-free plating and compliant to RoHS standards.
Parts marked as Green Products (with “L” suffix) use reduced levels of Halogens, and are also RoHS compliant.
RoHS Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information.
Compliant
Pin Configuration
1
8
2
7
3
3
6
4
4
5
1
Exposed Pad (GND)
8
7
6
5
2
DFN-8
Top View
(Bottom View)
Pin Description
Pin Number
Pin Name
1, 8
CH 1
Channel 1 Connections
2, 7
CH 2
Channel 2 Connections
3, 6
CH 3
Channel 3 Connections
4, 5
CH 4
Channel 4 Connections
Exposed Pad
GND
Common Ground Connection
Rev. 1.3 November 2008
Pin Function
www.aosmd.com
Page 2 of 6
AOZ8014
Absolute Maximum Ratings
Exceeding the Absolute Maximum ratings may damage the device.
Parameter
Rating
Storage Temperature (TS)
-65°C to +150°C
ESD Rating per IEC61000-4-2,
contact(1)
±17kV
ESD Rating per IEC61000-4-2,
air(1)
±17kV
ESD Rating per Human Body Model(2)
±30kV
Notes:
1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω.
2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ.
Electrical Characteristics
TA = 25°C unless otherwise specified.
Symbol
VRWM
VBR
IR
Parameter
Reverse Working Voltage
Conditions
1mA(4)
Reverse Breakdown Voltage
IT =
Reverse Leakage Current
VRWM = 3.3V
Units
5.0
V
8
V
0.1
µA
7.5
-6.5
8.5
-7.5
V
85
100
115
Ω
15
17
19
pF
clamp(5)(8)
Signal Clamp Voltage
ILOAD = 12A, positive
ILOAD = 12A, negative clamp(5)(8)
RCH
Total Series Resistance
IR = 20mA
fC
Max.
6
VCL
CCH
Min.
Typ.
(3)(8)
Ground(6)(7)(8)
7
Channel Capacitance
Input to
Cut-off Frequency
Measured with 50Ω source and 50Ω load
termination
125
MHz
Attenuation from 800MHz
to 3.0GHz
Measured with 50Ω source and 50Ω load
termination
-25
dB
Notes:
3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level.
4. VBR is measured at the pulse test current IT.
5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system.
6. Total capacitance is equal to 2 x CCH.
7. Measured at 25°C, VR = 2.5V, f = 1.0MHz.
8. Guaranteed by design.
Rev. 1.3 November 2008
www.aosmd.com
Page 3 of 6
AOZ8014
Typical Performance Characteristics
Typical Line Capacitance vs.
Reverse Bias Voltage
Insertion Loss Characteristics
0
1.50
@ 0V Bias
@ 5V Bias
-5
1.25
-10
Capacitance (pF)
S21 (db)
-15
-20
-25
-30
-35
-40
1.00
0.75
0.50
0.25
-45
0.00
-50
1
10
100
1000
1
10000
2
3
4
5
Reverse Biased Voltage (V)
Frequency (MHz)
Analog Crosstalk
Clamping Voltage
0
12.50
-20
Current (A)
S21 (db)
10.00
-40
-60
7.50
-80
5.00
-100
1
10
100
1000
10000
Frequency (MHz)
Rev. 1.3 November 2008
5
6
7
8
9
10
11
12
13
14
15
Forward Voltage (V)
www.aosmd.com
Page 4 of 6
AOZ8014
Package Dimensions, DFN 2.0 x 2.0 8L
b
D
E
R
E1
E
L
D1
TOP VIEW
A
c
BOTTOM VIEW
A1
Seating
Plane
SIDE VIEW
Dimensions in millimeters
RECOMMENDED LAND PATTERN
0.50
0.25
0.90
0.30
1.50
UNIT: mm
1.70
Symbols
A
A1
b
c
D
D1
E
E1
e
L
R
aaa
bbb
ccc
ddd
Min.
0.70
0.00
0.18
0.15
Nom.
0.75
0.02
0.25
0.20
2.00 BSC
1.35
1.50
2.00 BSC
0.75
0.90
0.50 BSC
0.20
0.30
0.20
0.15
0.10
0.10
0.08
Max.
0.80
0.05
0.30
0.25
1.60
1.00
0.40
Dimensions in inches
Symbols
A
A1
b
c
D
D1
E
E1
e
L
R
aaa
bbb
ccc
ddd
Min.
0.028
0.000
0.007
0.006
Nom. Max.
0.030 0.031
0.001 0.002
0.010 0.012
0.008 0.010
0.079 BSC
0.053 0.059 0.063
0.079 BSC
0.030 0.035 0.039
0.020 BSC
0.008 0.012 0.016
0.008
0.006
0.004
0.004
0.003
Notes:
1. Dimensions and tolerances conform to ASME Y14.5M-1994.
2. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact.
3. Dimension b applied to metallized terminal and is measured between 0.10mm and 0.30mm from the terminal tip. If the terminal
has the optional radius on the other end of the terminal, dimension b should not be measured in that radius area.
4. Coplanarity ddd applies to the terminals and all other bottom surface metallization.
Rev. 1.3 November 2008
www.aosmd.com
Page 5 of 6
AOZ8014
Part Marking
AOZ8014DI
(DFN-8)
AE2A
8F13
Part Code
Underscore Denotes Green Product
Year Code
Assembly Lot Location
Option Code
Assembly Lot Code
Week Code
This datasheet contains preliminary data; supplementary data may be published at a later date.
Alpha & Omega Semiconductor reserves the right to make changes at any time without notice.
LIFE SUPPORT POLICY
ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS.
As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant into
the body or (b) support or sustain life, and (c) whose
failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be
reasonably expected to result in a significant injury of
the user.
Rev. 1.3 November 2008
2. A critical component in any component of a life
support, device, or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
www.aosmd.com
Page 6 of 6
Similar pages