Vishay CRCW0603562MJKEA Standard thick film chip resistor Datasheet

D/CRCW e3
Vishay
Standard Thick Film Chip Resistors
FEATURES
 Stability R/R = 1 % for 1000 h at 70 ° C
 2 mm pitch packaging option for 0603 size
 Pure tin solder contacts on Ni barrier layer
provides compatibility with lead (Pb)-free and lead
containing soldering processes
 Metal glaze on high quality ceramic
 AEC-Q200 qualified
 Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
SIZE
MODEL
D10/CRCW0402
INCH
METRIC
0402
RR 1005M
RATED
DISSIPATION
P70 °C
W
0.063
LIMITING
ELEMENT TEMPERATURE TOLERANCE RESISTANCE
RANGE
COEFFICIENT
%
VOLTAGE

ppm/K
Umax. AC/DC
50
± 100
± 200
SERIES
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 2M2
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
±1
±5
1R0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 1.5 A
D11/CRCW0603
0603
RR 1608M
0.10
75
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.0 A
D12/CRCW0805
0805
RR 2012M
0.125
150
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.5 A
D25/CRCW1206
1206
RR 3216M
0.25
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 3.5 A
CRCW1210
1210
RR 3225M
0.5
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 5.0 A
CRCW1218
1218
RR 3246M
1.0
200
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 7.0 A
CRCW2010
2010
RR 5025M
0.75
400
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 6.0 A
CRCW2512
2512
RR 6332M
1.0
500
± 100
± 200
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 7.0 A
Notes
 These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
 Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020).
 Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
www.vishay.com
Document Number: 20035
For technical questions, contact: [email protected]
Revision: 04-Jun-12
125
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
TECHNICAL SPECIFICATIONS
D10/
D11/
D12/
D25/
UNIT CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW1218 CRCW2010 CRCW2512
PARAMETER
Rated dissipation P70 (1)
W
0.063
0.1
0.125
0.25
0.5
1.0
0.75
1.0
Limiting element voltage
Umax. AC/DC
V
50
75
150
200
200
200
400
500
Insulation voltage
Uins (1 min)
V
> 75
> 100
> 200
> 300
> 300
> 300
> 300
> 300
Insulation resistance

> 109
Category temperature
range
°C
- 55 to + 155
Failure rate
h-1
< 0.1 x 10- 9
Weight
mg
29.5
25.5
40.5
0.65
2
5.5
10
16
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW0603562RFKEC
C
R
C
W
0
6
0
3
5
6
2
R
F
K
E
C
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
SPECIAL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
R = Decimal
K = Thousand
M = Million
0000 = Jumper
F = ± 1.0 %
J = ± 5.0 %
Z = Jumper
K = ± 100 ppm/K
N = ± 200 ppm/K
0 = Jumper
EA, EB,
EC, ED,
EE, EF,
EG, EH,
EI, EL,
EK
Up to 2 digits
Product Description: D11/CRCW0603 100 562R 1 % ET6 e3
D11/CRCW0603
100
562R
1%
ET6
e3
MODEL
TCR
RESISTANCE VALUE
TOLERANCE
PACKAGING
LEAD (Pb)-FREE
D10/CRCW0402
D11/CRCW0603
D12/CRCW0805
D25/CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
± 200 ppm/K
± 100 ppm/K
10R = 10 
562R = 562 
10K = 10 k
1M0 = 1 M
0R0 = Jumper
±5%
±1%
ET1, ET2,
ET3, ET4,
ET5, ET6,
ET7, ET8,
ET9, EF4,
E02, E67,
E82
e3 = Pure tin
termination finish
Document Number: 20035
www.vishay.com
For technical questions, contact: [email protected]
126
Revision: 04-Jun-12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
PACKAGING
MODEL
CODE
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
QUANTITY
ED = ET7
10 000
EE = EF4
50 000
WIDTH
PITCH
8 mm
2 mm
REEL DIAMETER
180 mm/7"
330 mm/13"
EI = ET2
5000
ED = ET3
10 000
EL = ET4
20 000
EE = ET8
50 000
EA = ET1
5000
EB = ET5
10 000
EC = ET6
20 000
EA = ET1
5000
EB = ET5
10 000
EC = ET6
20 000
EA = ET1
5000
EB = ET5
10 000
EC = ET6
20 000
330 mm/13"
EA = ET1
5000
180 mm/7"
EB = ET5
10 000
EC = ET6
20 000
CRCW1218
EK = ET9
4000
CRCW2010
EF = E02
4000
EG = E67
2000
EH = E82
4000
CRCW2512
CARRIER TAPE
180 mm/7"
8 mm
180 mm/7"
2 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
8 mm
4 mm
285 mm/11.25"
Paper tape acc.
to IEC 60068-3
Type I
330 mm/13"
180 mm/7"
8 mm
4 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
8 mm
4 mm
285 mm/11.25"
8 mm
4 mm
285 mm/11.25"
12 mm
4 mm
180 mm/7"
12 mm
4 mm
180 mm/7"
330 mm/13"
Blister tape acc.
to IEC 60068-3
Type II
8 mm
12 mm
180 mm/7"
4 mm
DIMENSIONS
SIZE
INCH METRIC
SOLDER PAD DIMENSIONS in millimeters
DIMENSIONS in millimeters
L
W
T2
a
b
l
0402
1005
1.0 ± 0.05
0.5 ± 0.05
0.35 ± 0.05 0.25 ± 0.05
0.2 ± 0.1
0.4
0.6
0.5
0603
1608
1.55
+ 0.10
- 0.05
0.85 ± 0.1
0.45 ± 0.05
0.3 ± 0.2
0.5
0.9
0805
2012
2.0
+ 0.20
- 0.10
1.25 ± 0.15
0.45 ± 0.05
+ 0.20
- 0.10
0.3 ± 0.2
0.7
1206
3216
3.2
+ 0.10
- 0.20
1.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
1210
3225
3.2 ± 0.2
3.2
H
T1
REFLOW SOLDERING
0.3 ± 0.2
0.3
WAVE SOLDERING
a
b
l
1.0
0.9
0.9
1.0
1.3
1.2
0.9
1.3
1.3
0.9
1.7
2.0
1.1
1.7
2.3
2.5 ± 0.2
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
0.9
2.5
2.0
1.1
2.5
2.2
+ 0.10
- 0.20
4.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
1.05
4.9
1.9
1.25
4.8
1.9
1218
3246
2010
5025
5.0 ± 0.15
2.5 ± 0.15
0.6 ± 0.1
0.6 ± 0.2
0.6 ± 0.2
1.0
2.5
3.9
1.2
2.5
3.9
2512
6332
6.3 ± 0.2
3.15 ± 0.15
0.6 ± 0.1
0.6 ± 0.2
0.6 ± 0.2
1.0
3.2
5.2
1.2
3.2
5.2
www.vishay.com
Document Number: 20035
For technical questions, contact: [email protected]
Revision: 04-Jun-12
127
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
Pulse Load Pmax. (W)
FUNCTIONAL PERFORMANCE
Single Pulse
1000
2512
1218
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration t i (s)
Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Ûmax.;
for permissible resistance change equivalent to 8000 h operation
Continuous Pulse Load Pmax. (W)
Continuous Pulse
1000
2512
1218
2010
1210
1206
0805
0603
0402
100
10
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration t i (s)
Pulse Voltage Û
max.
(V)
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Û ≤ Ûmax.;
for permissible resistance change equivalent to 8000 h operation
2000
1800
2512
1600
1400
2010
1200
1000
800
1206/1210/1218
600
400
0805
0603
200
0402
0 -6
10- 5
10
10- 4
10- 3
10- 2
10- 1
1
10
Pulse Duration t i (s)
Maximum pulse voltage, single and continuous pulses; applicable if
P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation
Document Number: 20035
www.vishay.com
For technical questions, contact: [email protected]
128
Revision: 04-Jun-12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
Fraction of Rated Dissipation P70
Derating
100
%
50
0
Attenuation of 3rd Harmonic A3 in dB
- 50
0
50
100
°C
150
70
Ambient Temperature ϑamb
120
100
80
1206, 2010
0805
60
0603
0402
40
20
0
10
100
1K
10K
100K
1M
10M
Current Noise A1 in µV/V
Resistance Value R in Ω
100
2
040
3
0
6
0
5
080 6
120 0
201
10
1
0.1
0.01
100
1K
10K
100K
1M
10M
Resistance Value R in Ω
www.vishay.com
Document Number: 20035
For technical questions, contact: [email protected]
Revision: 04-Jun-12
129
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN
60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
REQUIREMENTS
PERMISSIBLE CHANGE (R)
TEST
SIZE 0402 to 2512
PROCEDURE
STABILITY
CLASS 2
OR BETTER
STABILITY
CLASS 1
OR BETTER
Stability for product types:
1  to 10 M
D/CRCW e3
4.5
-
Resistance
4.7
-
Voltage proof
U = 1.4 x Uins; 60 s
Short time overload
U = 2.5 x P 70 x R
 2 x Umax.;
duration: Acc. to style
4.13
4.17.2
-
58 (Td)
Solderability
-
21 (Uu3)
Shear
(adhesion)
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
4.33
21 (Uu1)
Substrate bending
Depth 2 mm;
3 times
14 (Na)
Rapid change of
temperature
No visible damage
No visible damage, no open circuit in bent position
± (0.25 % R + 0.05 )
5 cycles
± (0.25 % R + 0.05 )
± (0.5 % R + 0.05 )
± (1 % R + 0.05 )
± (1 % R + 0.05 )
± (1 % R + 0.05 )
± (2 % R + 0.1 )
Climatic sequence:
2 (Ba)
Dry heat
125 °C; 16 h
-
4.23.3
30 (Db)
Damp heat, cyclic
4.23.4
1 (Aa)
Cold
- 55 °C; 2 h
4.23.5
13 (M)
Low air pressure
1 kPa; (25 ± 10) °C; 1 h
4.23.6
30 (Db)
Damp heat, cyclic
55 °C;  90 % RH;
24 h; 5 cycles
4.23.7
-
DC load
Endurance
at 70 °C
± 200 ppm/K
1000 cycles
-
-
± 100 ppm/K
30 min. at - 55 °C;
30 min. at 125 °C
55 °C;  90 % RH;
24 h; 1 cycle
4.25.1
±0.5 % R + 0.05)
Good tinning ( 95 % covered)
no visible damage
4.32
4.23.2
±0.25 % R + 0.05)
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) C
(3 ± 0.3) s
(20/- 55/20) C and
(20/125/20) C
4.23
No flashover or breakdown
Good tinning ( 95 % covered)
no visible damage
Temperature
coefficient
4.19
±5%
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
-
4.8.4.2
±1%
U = P 70 x R
U = P 70 x R  Umax.;
1.5 h on; 0.5 h off;
70 °C; 1000 h
± (1 % R + 0.05 )
± (2 % R + 0.1 )
70 °C; 8000 h
± (2 % R + 0.1 )
± (4 % R + 0.1 )
Document Number: 20035
www.vishay.com
For technical questions, contact: [email protected]
130
Revision: 04-Jun-12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
D/CRCW e3
Standard Thick Film Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
IEC
EN
60068-2
60115-1
TEST
CLAUSE
METHOD
REQUIREMENTS
PERMISSIBLE CHANGE (R)
TEST
SIZE 0402 to 2512
PROCEDURE
STABILITY
CLASS 2
OR BETTER
STABILITY
CLASS 1
OR BETTER
Stability for product types:
1  to 10 M
D/CRCW e3
58 (Td)
Resistance to
soldering heat
Solder bath method
(260 ± 5) C;
(10 ± 1) s
4.35
-
Flamability,
needle flame test
IEC 60695-11-5;
10 s
No burning after 30 s
4.24
78 (Cab)
Damp heat,
steady state
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
± (1 % R + 0.05 )
4.25.3
-
Endurance at
upper category
temperature
155 °C, 1000 h
4.40
-
Electrostatic
discharge
(human body model)
IEC 61340-3-1;
3 pos. + 3 neg.
discharges;
ESD voltage acc. to size
± (1 % R + 0.05 )
4.29
45 (XA)
Component solvent
resistance
Isopropyl alcohol;
50 °C; method 2
No visible damage
4.30
45 (XA)
Solvent resistance
of marking
Isopropyl alcohol;
50 °C; method 1,
toothbrush
Marking legible,
no visible damage
4.22
6 (Fc)
Vibration, endurance
by sweeping
f = 10 Hz to 2000 Hz;
x, y, z  1.5 mm;
A  200 m/s2;
10 sweeps per axis
4.37
-
Periodic electric
overload
4.27
-
Single pulse high
voltage overload,
10 µs/700 µs
4.18.2
± (0.25 % R + 0.05 )
± (1 % R + 0.05 )
± (0.25 % R + 0.05 )
± (0.5 % R + 0.05 )
± (2 % R + 0.1 )
± (0.5 % R + 0.05 )
U=
15 x P 70 x R
 2 x Umax.;
0.1 s on; 2.5 s off;
1000 cycles
Û = 10 x P 70 x R
 2 x Umax.;
10 pulses
± (1 % R + 0.05 )
± (1 % R + 0.05 )
All tests are carried out in accordance with the following specifications:
 EN 60115-1, generic specification
 EN 140400, sectional specification
 EN 140401-802, detail specification
 IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
www.vishay.com
Document Number: 20035
For technical questions, contact: [email protected]
Revision: 04-Jun-12
131
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
CRCW06036K65FKEA CRCW120616R9FKEA CRCW1206680KFKEA CRCW1206280KFKEA
CRCW06031K21FKEA CRCW120663R4FKEA CRCW1206619KFKEA CRCW06032K21FKEA
CRCW120662K0JNEA CRCW120624K0FKEA CRCW1206287KFKEA CRCW0603121KFKEA
CRCW1206487KFKEA CRCW0603221KFKEA CRCW120634R8FKEA CRCW0603240RJNEA
CRCW0603300RFKEA CRCW0603976RFKEA CRCW12067K32FKEA CRCW060315R0JNEA
CRCW060334R0FKEA CRCW120617R8FKEA CRCW1206787KFKEA CRCW060330R0JNEA
CRCW060350R0FKEA CRCW0603768KFKEA CRCW0603432RFKEA CRCW0603619RFKEA
CRCW12061K80FKEA CRCW12066K80FKEA CRCW0603953KFKEA CRCW120610R5FKEA
CRCW06037M50JNEA CRCW06031M50JNEA CRCW120668K0JNEA CRCW060375R0FKEA
CRCW0603340KFKEA CRCW0603140KFKEA CRCW06039K31FKEA CRCW0603240KFKEA
CRCW060359K0FKEA CRCW1206698KFKEA CRCW06032R49FKEA CRCW12066M81FKEA
CRCW06035R62FKEA CRCW1206309KFKEA CRCW120632R4FKEA CRCW120612R4FKEA
CRCW12065M76FKEA CRCW12069M76FKEA CRCW120695R3FKEA CRCW120610R7FKEA
CRCW060375K0FKEA CRCW06038M20JNEA CRCW12067R50JNEA CRCW0603316KFKEA
CRCW06032R70JNEA CRCW12061R80JNEA CRCW0603953RFKEA CRCW060382R0FKEA
CRCW060349R9FKEA CRCW0603576RFKEA CRCW120662K0FKEA CRCW060363K4FKEA
CRCW0603510KFKEA CRCW060360K4FKEA CRCW0603210KFKEA CRCW0603110KFKEA
CRCW06031R10JNEA CRCW060327K4FKEA CRCW1206422KFKEA CRCW0603287KFKEA
CRCW120644R2FKEA CRCW0603487KFKEA CRCW0603187KFKEA CRCW0603787KFKEA
CRCW12062R70JNEA CRCW120657R6FKEA CRCW12064M99FKEA CRCW0603360RJNEA
CRCW060332K4FKEA CRCW060337K4FKEA CRCW060312K4FKEA CRCW060317K4FKEA
CRCW060315K4FKEA CRCW060346K4FKEA CRCW0603549RFKEA CRCW060351R1FKEA
CRCW060390R9FKEA CRCW0603820KFKEA CRCW1206113KFKEA CRCW0603301KFKEA
CRCW0603270RJNEA CRCW0603243RFKEA CRCW06038K06FKEA CRCW06031K91FKEA
CRCW1206300KJNEA CRCW1206200KJNEA CRCW06032K20FKEA CRCW060323R2FKEA
Similar pages