TI AM26LS33AC Quadruple differential line receiver Datasheet

AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
D
D
D
D
D
D
D
D
D
AM26LS32AC . . . D, N, OR NS PACKAGE
AM26LS32AI, AM26LS33AC . . . D OR N PACKAGE
AM26LS32AM, AM26LS33AM . . . J PACKAGE
(TOP VIEW)
AM26LS32A Devices Meet or Exceed the
Requirements of ANSI TIA/EIA-422-B,
TIA/EIA-423-B, and ITU Recommendations
V.10 and V.11
AM26LS32A Devices Have ±7-V
Common-Mode Range With ±200-mV
Sensitivity
AM26LS33A Devices Have ±15-V
Common-Mode Range With ±500-mV
Sensitivity
Input Hysteresis . . . 50 mV Typical
Operate From a Single 5-V Supply
Low-Power Schottky Circuitry
3-State Outputs
Complementary Output-Enable Inputs
Input Impedance . . . 12 kΩ Min
Designed to Be Interchangeable With
Advanced Micro Devices AM26LS32 and
AM26LS33
1B
1A
1Y
G
2Y
2A
2B
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
4B
4A
4Y
G
3Y
3A
3B
AM26LS32AM, AM26LS33AM . . . FK PACKAGE
(TOP VIEW)
1A
1B
NC
VCC
4B
D
1Y
G
NC
2Y
2A
description
3
2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
4A
4Y
NC
G
3Y
2B
GND
NC
3B
3A
The AM26LS32A and AM26LS33A devices are
quadruple differential line receivers for balanced
and unbalanced digital data transmission. The
enable function is common to all four receivers
and offers a choice of active-high or active-low
input. The 3-state outputs permit connection
directly to a bus-organized system. Fail-safe
design ensures that, if the inputs are open, the
outputs always are high.
4
NC – No internal connection
Compared to the AM26LS32 and the AM26LS33, the AM26LS32A and AM26LS33A incorporate an additional
stage of amplification to improve sensitivity. The input impedance has been increased, resulting in less loading
of the bus line. The additional stage has increased propagation delay; however, this does not affect
interchangeability in most applications.
The AM26LS32AC and AM26LS33AC are characterized for operation from 0°C to 70°C. The AM26LS32AI is
characterized for operation from –40°C to 85°C. The AM26LS32AM and AM26LS33AM are characterized for
operation over the full military temperature range of –55°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
AM26LS32 and AM26LS33 are trademarks of Advanced Micro Devices, Inc.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
FUNCTION TABLE
(each receiver)
DIFFERENTIAL
A–B
VID ≥ VIT
IT+
VIT
IT
IT– ≤ VID ≤ VIT+
VID ≤ VIT
IT–
X
Open
ENABLES
OUTPUT
Y
G
G
H
X
H
X
L
H
H
X
?
X
L
?
H
X
L
X
L
L
L
H
Z
H
X
H
X
L
H
H = high level, L = low level, ? = indeterminate,
X = irrelevant, Z = high impedance (off)
logic diagram (positive logic)
G
G
1A
1B
2A
2B
3A
3B
4A
4B
2
4
12
2
1
6
7
10
9
14
15
POST OFFICE BOX 655303
3
5
11
13
1Y
2Y
3Y
4Y
• DALLAS, TEXAS 75265
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
schematics of inputs and outputs
EQUIVALENT OF EACH
DIFFERENTIAL INPUT
EQUIVALENT OF EACH ENABLE INPUT
VCC
TYPICAL OF ALL OUTPUTS
VCC
85 Ω
NOM
VCC
8.3 kΩ
NOM
100 kΩ
A Input Only
960 Ω
NOM
20 kΩ
NOM
Enable
Output
Input
960 Ω
NOM
100 kΩ
B Input Only
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI: Any differential input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 V
Other inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Package thermal impedance, θJA (see Note 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
Case temperature for 60 seconds, TC: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or N package . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the network ground terminal.
2. Differential voltage values are at the noninverting (A) input terminals with respect to the inverting (B) input terminals.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 125°C
POWER RATING
FK
1375 mW
11.0 mW/°C
880 mW
275 mW
J
1375 mW
11.0 mW/°C
880 mW
275 mW
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
recommended operating conditions
VCC
Supply voltage
VIH
VIL
High-level input voltage
AM26LS32AC, AM26LS32AI, AM26LS33AC
AM26LS32AM, AM26LS33AM
MIN
NOM
MAX
4.75
5
5.25
4.5
5
5.5
2
UNIT
V
V
Low-level input voltage
0.8
AM26LS32A
±7
AM26LS33A
±15
V
VIC
Common mode input voltage
Common-mode
IOH
IOL
High-level output current
–440
µA
Low-level output current
8
mA
AM26LS32AC, AM26LS33AC
TA
Operating free-air temperature
0
V
70
AM26LS32AI
–40
85
AM26LS32AM, AM26LS33AM
–55
125
°C
electrical characteristics over recommended ranges of VCC, VIC, and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT
IT+
Positive-going
g g
input threshhold voltage
VO = VOHmin
min, IOH = –440
440 µA
VIT
IT–
Negative-going
g
g g
input threshhold voltage
VO = 0
0.45
45 V
V, IOL = 8 mA
VIK
Hysteresis voltage
(VIT+ – VIT–)
Enable-input clamp voltage
VOH
High
level output voltage
High-level
Vhys
TYP†
MAX
AM26LS32A
0.2
AM26LS33A
0.5
AM26LS32A
AM26LS33A
–0.2‡
–0.5‡
VCC = MIN,
VCC =MIN,, VID = 1 V,,
VI(G) = 0.8 V, IOH = –440 µA
Low level output voltage
Low-level
VCC = MIN,, VID = –1 V,,
VI(G) = 0.8 V
IOZ
Off-state
(high impedance state)
(high-impedance
output current
VCC = MAX
II
Line input current
VI = 15 V,
VI = –15 V,
II(EN)
IIH
Enable input current
IIL
rI
Low-level enable current
Input resistance
VI = 0.4 V
VIC = –15 V to 15 V,
IOS
Short-circuit output current§
VCC = MAX
II = –18 mA
AM26LS32AC
AM26LS33AC
AM26LS32AM, AM26LS32AI,
AM26LS33AM
V
mV
–1.5
V
2.7
V
2.5
IOL = 4 mA
IOL = 8 mA
0.45
VO = 2.4 V
20
VO = 0.4 V
–20
0.4
Other input at –10 V to 15 V
1.2
Other input at –15 V to 10 V
–1.7
VI = 5.5 V
VI = 2.7 V
100
One input to ac ground
UNIT
V
50
VOL
High-level enable current
MIN
12
–15
V
µA
mA
µA
20
µA
–0.36
mA
15
kΩ
–85
mA
ICC
Supply current
VCC = MAX,
All outputs disabled
52
70
mA
† All typical values are at VCC = 5 V, TA = 25°C, and VIC = 0.
‡ The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for threshold levels
only.
§ Not more than one output should be shorted to ground at a time, and duration of the short circuit should not exceed one second.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
switching characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
tPLH
tPHL
Propagation delay time, low-to-high-level output
tPZH
tPZL
Output enable time to high level
tPHZ
tPLZ
Output disable time from high level
Propagation delay time, high-to-low-level output
Output enable time to low level
Output disable time from low level
MIN
pF
CL = 15 pF,
See Figure 1
CL = 15 pF,
pF
See Figure 1
CL = 5 pF,
pF
See Figure 1
TYP
MAX
20
35
22
35
17
22
20
25
21
30
30
40
UNIT
ns
ns
ns
PARAMETER MEASUREMENT INFORMATION
VCC
Test
Point
RL = 2 kΩ
2.5 V
S1
From Output
Under Test
CL
(see Note A)
Input
0
0
–2.5 V
5 kΩ
tPLH
See Note B
tPHL
VOH
Output
S2
1.3 V
1.3 V
VOL
S1 and S2 Closed
TEST CIRCUIT
VOLTAGE WAVEFORMS FOR tPLH, tPHL
≤5 ns
90%
Enable G
1.3 V
≤5 ns
3V
90%
10%
See Note C
90%
90%
10%
Output
S1 Open
S2 Closed
0
See Note C
3V
90%
90%
10%
S1 Closed
S2 Closed
tPZL
VOH
≈1.4 V
S1 Closed
S2 Closed
1.3 V
Output
VOLTAGE WAVEFORMS FOR tPHZ, tPZH
S1 Closed
S2 Open
3V
1.3 V
1.3 V
10%
1.3 V
tPHZ
1.3 V
10%
0
0.5 V
3V
90%
1.3 V
Enable G
10%
tPZH
≤5 ns
10%
0
1.3 V
1.3 V
90%
Enable G
1.3 V
10%
Enable G
≤5 ns
tPLZ
0
≈1.4 V
VOL
0.5 V
VOLTAGE WAVEFORMS FOR tPLZ, tPZL
NOTES: A. CL includes probe and jig capacitance.
B. All diodes are 1N3064 or equivalent.
C. Enable G is tested with G high; G is tested with G low.
Figure 1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT†
HIGH-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5
5
4
3
VOH – High-Level Output Voltage – V
VOH – High-Level Output Voltage – V
VID = 0.2 V
TA = 25°C
VCC = 5.25 V
VCC = 5 V
2
VCC = 5.5 V
VCC = 4.75 V
1
VCC = 4.5 V
VCC = 5 V
VID = 0.2 mV
IOH = –440 µA
4
3
2
1
0
0
–10
–20
–30
–40
–50
0
IOH – High-Level Output Current – mA
0
10
† VCC = 5.5 V and VCC = 4.5 V applies to M-suffix devices only.
20
30
40
50
60
TA – Free-Air Temperature – °C
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.5
0.6
VCC = 5 V
TA = 25°C
VID = –0.2 mV
0.5
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
80
Figure 3
Figure 2
0.4
0.3
0.2
0.1
0
VCC = 5 V
VID = –0.2 V
IOL = 8 mA
0.4
0.3
0.2
0.1
0
0
15
20
25
10
IOL – Low-Level Output Current – mA
5
30
0
10
Figure 4
6
70
20
30
40
50
60
TA – Free-Air Temperature – °C
Figure 5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
70
80
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE
vs
ENABLE G VOLTAGE
OUTPUT VOLTAGE
vs
ENABLE G VOLTAGE
5
5
VID = 0.2 V
TA = 25°C
Load = 8 kΩ to GND
4.5
VCC = 5.5 V
4
4
VCC = 5 V
3.5
VO – Output Voltage – V
VO – Output Voltage – V
VCC = 5 V
VID = 0.2 V
Load = 8 kΩ to GND
4.5
VCC = 4.5 V
3
2.5
2
1.5
TA = 70°C
TA = 25°C
TA = 0°C
3.5
3
2.5
2
1.5
1
1
0.5
0.5
0
0
0
0.5
1
1.5
2
2.5
0
3
0.5
1
1.5
2
2.5
3
Enable G Voltage – V
Enable G Voltage – V
Figure 6
Figure 7
OUTPUT VOLTAGE
vs
ENABLE G VOLTAGE
OUTPUT VOLTAGE
vs
ENABLE G VOLTAGE
6
6
VCC = 5.5 V
VCC = 5 V
5
5
VO – Output Voltage – V
VO – Output Voltage – V
VCC = 4.5 V
4
3
2
1
0
0.5
1
TA = 70°C
3
2
1
VID = –0.2 V
Load = 1 kΩ to VCC
TA = 25°C
0
TA = 0°C
TA = 25°C
4
1.5
2
2.5
3
VCC = 5 V
VID = –0.2 V
Load = 1 kΩ to VCC
0
0
0.5
Enable G Voltage – V
1
1.5
2
2.5
3
Enable G Voltage – V
Figure 9
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
TYPICAL CHARACTERISTICS
AM26LS32A
AM26LS33A
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
OUTPUT VOLTAGE
vs
DIFFERENTIAL INPUT VOLTAGE
5
5
VO – Output Voltage – V
4
VCC = 5 V, IO = 0, TA = 25°C
4.5
4
VIC =
–7 V
3.5
VIC =
0
VO – Output Voltage – V
4.5
VCC = 5 V
IO = 0
TA = 25°C
VIC =
7V
3
2.5
2
VIT–
VIT+
1.5
VIT–
VIT+
VIT–
VIT+
2
0.5
100
VIT–
VIT–
VIT+
1.5
0.5
50
VID – Differential Input Voltage – mV
VIT–
VIT+
0
–200 –150 –100 –50
150 200
VIC =
15 V
2.5
1
0
VIC =
0
3
1
0
–200 –150 –100 –50
VIC =
–15 V
3.5
0
VIT+
50
100
150 200
VID – Differential Input Voltage – mV
Figure 11
Figure 10
INPUT CURRENT
vs
INPUT VOLTAGE
4
3
I I – Input Current – mA
2
1
0
VCC = 0
–1
–2
VCC = 5 V
The Unshaded Area
Shows Requirements of
Paragraph 4.2.1 of ANSI
Standards EIA/TIA-422-B and
EIA/TIA-423-B.
–3
–4
–25 –20 –15 –10 –5
0
5
10
15
VI – Input Voltage – V
Figure 12
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
20
25
AM26LS32AC, AM26LS32AI, AM26LS33AC,
AM26LS32AM, AM26LS33AM
QUADRUPLE DIFFERENTIAL LINE RECEIVERS
SLLS115D – OCTOBER 1980 – REVISED MARCH 2002
APPLICATION INFORMATION
1/4 AM26LS31AC
1/4 AM26LS32AC
Data
In
RT†
1/4 AM26LS32AC
Data
Out
1/4 AM26LS33AC
Data
Out
Data
Out
† RT equals the characteristic impedance of the line.
Figure 13. Circuit With Multiple Receivers
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated
Similar pages