Kingbright APHBM2012QBDSURKC Ideal for backlight and indicator. Datasheet

2.0x1.25mm SMD CHIP LED LAMP
Part Number: APHBM2012QBDSURKC
ATTENTION
Blue
Hyper Red
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 2.0mmx1.25mm SMD LED, 0.45mm max. thickness.
z The Blue source color devices are made with InGaN
z Bi -color, low power consumption.
Light Emitting Diode.
z The Hyper Red source color devices are made with
z Wide viewing angle.
z Ideal for backlight and indicator.
AlGaInP on GaAs substrate Light Emitting Diode.
z Electrostatic discharge and power surge could damage
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
the LEDs.
z It is recommended to use a wrist band or anti-
z RoHS compliant.
electrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 1 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
Selection Guide
Part No.
Emitting Color (Material)
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Lens Type
Min.
Typ.
40
80
*40
*80
120
250
*40
*80
2θ1/2
Blue (InGaN)
APHBM2012QBDSURKC
Water Clear
Hyper Red (AlGaInP)
120°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
* Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Blue
Hyper Red
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
460
645
nm
IF=20mA
Blue
Hyper Red
465
630
nm
IF=20mA
Spectral Line Half-width
Blue
Hyper Red
25
28
nm
IF=20mA
C
Capacitance
Blue
Hyper Red
100
35
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Blue
Hyper Red
3.3
1.95
4
2.5
V
IF=20mA
IR
Reverse Current
Blue
Hyper Red
50
10
uA
VR = 5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Blue
Hyper Red
Units
Power dissipation
120
75
mW
DC Forward Current
30
30
mA
Peak Forward Current [1]
150
185
mA
Electrostatic Discharge Threshold (HBM)
250
3000
V
Reverse Voltage
5
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
V
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 2 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
APHBM2012QBDSURKC
Blue
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 3 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
Hyper Red
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 4 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
APHBM2012QBDSURKC
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 5 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
PACKING & LABEL SPECIFICATIONS
APHBM2012QBDSURKC
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAJ8666
REV NO: V.8A
DATE: NOV/18/2016
PAGE: 6 OF 6
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203010215
Similar pages