Data Delay DDU4F-5075MC 5-tap, ttl-interfaced fixed delay line (series ddu4f) Datasheet

DDU4F
data 3 
delay
devices, inc.
5-TAP, TTL-INTERFACED
FIXED DELAY LINE
(SERIES DDU4F)
FEATURES
PACKAGES
•
•
•
•
•
Five equally spaced outputs
Fits standard 14-pin DIP socket
Low profile
Auto-insertable
Input & outputs fully TTL interfaced & buffered
•
10 T L fan-out capability
2
IN
1
T2
4
T4
6
GND
7
DDU4F-xx
DDU4F-xxA2
DDU4F-xxB2
DDU4F-xxM
14
VCC
12
T1
10
T3
8
T5
IN
N/C
N/C
T2
N/C
T4
GND
DIP
Gull-Wing
J-Lead
Military DIP
FUNCTIONAL DESCRIPTION
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VDD
N/C
T1
N/C
T3
N/C
T5
Military SMD
DDU4F-xxMC2
PIN DESCRIPTIONS
The DDU4F-series device is a 5-tap digitally buffered delay line. The
IN
Signal Input
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
T1-T5
Tap Outputs
amount determined by the device dash number (See Table). For dash
VCC
+5 Volts
numbers less than 5025, the total delay of the line is measured from T1 to
GND
Ground
T5. The nominal tap-to-tap delay increment is given by one-fourth of the
total delay, and the inherent delay from IN to T1 is nominally 3.5ns. For
dash numbers greater than or equal to 5025, the total delay of the line is measured from IN to T5. The
nominal tap-to-tap delay increment is given by one-fifth of this number.
SERIES SPECIFICATIONS
•
•
•
•
•
•
DASH NUMBER SPECIFICATIONS
Minimum input pulse width: 20% of total delay
Output rise time: 2ns typical
Supply voltage: 5VDC ± 5%
Supply current: ICCL = 32ma typical
ICCH = 7ma typical
Operating temperature: 0° to 70° C
Temp. coefficient of total delay: 100 PPM/°C
3.5ns
VCC IN
25%
T1
25%
T2
25%
T3
25%
T4
T5 GND
Functional diagram for dash numbers < 5025
20%
VCC IN
20%
T1
20%
T2
20%
T3
20%
T4
T5 GND
Functional diagram for dash numbers >= 5025
 1997 Data Delay Devices
Part
Number
DDU4F-5004
DDU4F-5006
DDU4F-5008
DDU4F-5010
DDU4F-5012
DDU4F-5016
DDU4F-5020
DDU4F-5025
DDU4F-5030
DDU4F-5040
DDU4F-5050
DDU4F-5060
DDU4F-5075
DDU4F-5100
DDU4F-5125
DDU4F-5150
DDU4F-5200
DDU4F-5250
DDU4F-5300
DDU4F-5400
DDU4F-5500
Total
Delay (ns)
4 ± 1.0 *
6 ± 1.0 *
8 ± 2.0 *
10 ± 2.0 *
12 ± 2.0 *
16 ± 2.0 *
20 ± 3.0 *
25 ± 3.0
30 ± 3.0
40 ± 3.0
50 ± 3.0
60 ± 3.0
75 ± 4.0
100 ± 5.0
125 ± 6.5
150 ± 7.5
200 ± 10.0
250 ± 12.5
300 ± 15.0
400 ± 20.0
500 ± 25.0
Delay Per
Tap (ns)
1.0 ± 0.5
1.5 ± 0.5
2.0 ± 1.0
2.5 ± 1.0
3.0 ± 1.0
4.0 ± 1.5
5.0 ± 2.0
5.0 ± 2.0
6.0 ± 2.0
8.0 ± 2.0
10.0 ± 3.0
12.0 ± 3.0
15.0 ± 3.0
20.0 ± 3.0
25.0 ± 3.0
30.0 ± 3.0
40.0 ± 4.0
50.0 ± 5.0
60.0 ± 6.0
80.0 ± 8.0
100.0 ± 10.0
* Total delay is referenced to first tap output
Input to first tap = 3.5ns ± 1ns
NOTE: Any dash number between 5004 and 5500
not shown is also available.
Doc #97033
12/10/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
1
DDU4F
APPLICATION NOTES
Delay Devices if your application requires device
testing at a specific input condition.
HIGH FREQUENCY RESPONSE
The DDU4F tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 20% of the total delay and periods as
small as 40% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
POWER SUPPLY BYPASSING
The DDU4F relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VCC to GND,
located as close as possible to the VCC pin, is
recommended. A wide VCC trace and a clean
ground plane should be used.
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Supply Voltage
Input Pin Voltage
Storage Temperature
Lead Temperature
SYMBOL
VCC
VIN
TSTRG
TLEAD
MIN
-0.3
-0.3
-55
MAX
7.0
VDD+0.3
150
300
UNITS
V
V
C
C
NOTES
10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER
High Level Output Voltage
SYMBOL
VOH
Low Level Output Voltage
VOL
High Level Output Current
Low Level Output Current
High Level Input Voltage
Low Level Input Voltage
Input Clamp Voltage
Input Current at Maximum
Input Voltage
High Level Input Current
Low Level Input Current
Short-circuit Output Current
Output High Fan-out
Output Low Fan-out
IOH
IOL
VIH
VIL
VIK
IIHH
Doc #97033
12/10/97
IIH
IIL
IOS
MIN
2.5
TYP
3.4
MAX
UNITS
V
0.35
0.5
V
-1.0
20.0
0.8
-1.2
0.1
mA
mA
V
V
V
mA
20
-0.6
-150
25
12.5
µA
mA
mA
Unit
Load
2.0
-60
NOTES
VCC = MIN, IOH = MAX
VIH = MIN, VIL = MAX
VCC = MIN, IOL = MAX
VIH = MIN, VIL = MAX
VCC = MIN, II = IIK
VCC = MAX, VI = 7.0V
VCC = MAX, VI = 2.7V
VCC = MAX, VI = 0.5V
VCC = MAX
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
2
DDU4F
PACKAGE DIMENSIONS
14
12
10
8
Lead Material:
Nickel-Iron alloy 42
TIN PLATE
14
12
4
6
8
.410
TYP.
1
1
10
4
6
7
7
.280
MAX.
.780 MAX.
.820 MAX.
.290
MAX.
.020 .320
TYP. MAX.
.130
±.030
.015 TYP.
.010±.002
.018
TYP.
.070 MAX.
.350
MAX.
.600±.010
.020 TYP.
.100
TYP.
.018 TYP.
.600 TYP.
.300
TYP.
DDU4F-xxM (Military DIP)
DDU4F-xx (Commercial DIP)
.020 TYP.
.040
TYP.
14
12
10
.010 TYP.
8
14
.270
TYP.
1
4
.090
6
12
.300
MAX.
.050
TYP.
DDU4F-xxA2 (Commercial Gull-Wing)
.020 TYP.
9
4
.110
.090
3
4
5
6
.100
.600
.780±.020
7
.100
.600
.790 MAX.
.350
MAX.
.110
TYP.
.010±.002
8
.882
±.005
.710 .590
±.005 MAX.
2
6
DDU4F-xxB2 (Commercial J-Lead)
.040
TYP.
14 13 12 11 10
.320
TYP.
.270
TYP.
1
.100
.600
.790 MAX.
.050 TYP.
8
10
.430
TYP.
7
1
.040
TYP.
.020 TYP.
.007
±.005
7
.280
MAX.
.050
±.010
DDU4F-xxMC2 (Military SMD)
Doc #97033
12/10/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
3
DDU4F
DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT:
o
o
Ambient Temperature: 25 C ± 3 C
Supply Voltage (Vcc): 5.0V ± 0.1V
Input Pulse:
High = 3.0V ± 0.1V
Low = 0.0V ± 0.1V
Source Impedance:
50Ω Max.
Rise/Fall Time:
3.0 ns Max. (measured
between 0.6V and 2.4V )
Pulse Width:
PWIN = 1.5 x Total Delay
Period:
PERIN = 10 x Total Delay
OUTPUT:
Load:
Cload:
Threshold:
1 FAST-TTL Gate
5pf ± 10%
1.5V (Rising & Falling)
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
PRINTER
COMPUTER
SYSTEM
REF
PULSE
GENERATOR
OUT
IN
TRIG
DEVICE UNDER
TEST (DUT)
T1
IN
T2
TRIG
TIME INTERVAL
COUNTER
T3
T4
T5
Test Setup
PERIN
PWIN
TRISE
INPUT
SIGNAL
TFALL
VIH
2.4V
1.5V
0.6V
2.4V
1.5V
0.6V
TRISE
VIL
TFALL
VOH
OUTPUT
SIGNAL
1.5V
1.5V
VOL
Timing Diagram For Testing
Doc #97033
12/10/97
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
4
Similar pages